On TrimSlice, Tegra's USB1 port may be routed to either an external micro
USB port, or an internal USB->SATA bridge for SSD or HDD. This muxing is
controlled by a GPIO. Whilst not strictly a VBUS GPIO, the TrimSlice
board files caused this GPIO to be set appropriately to enable the SATA
bridge by passing it as the VBUS GPIO to the USB driver. Echo this same
configuration in device tree to enable the SATA bridge.
An alternative might be to implement a full USB bus mux driver. However,
that seems over-complex right now.
Commit 9fa2df6b90786301b175e264f5fa9846aba81a65
(ARM: OMAP2+: OPP: allow OPP enumeration to continue if device is not present)
makes the logic:
for (i = 0; i < opp_def_size; i++) {
<snip>
if (!oh || !oh->od) {
<snip>
continue;
}
<snip>
opp_def++;
}
In short, the moment we hit a "Bad OPP", we end up looping the list
comparing against the bad opp definition pointer for the rest of the
iteration count. Instead, increment opp_def in the for loop itself
and allow continue to be used in code without much thought so that
we check the next set of OPP definition pointers :)
Cc: Steve Sakoman <steve@sakoman.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Albert Pool<albertpool@solcon.nl> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we call scsi_unprep_request() the command associated with the request
gets destroyed and therefore drops its reference on the device. If this was
the only reference, the device may get released and we end up with a NULL
pointer deref when we call blk_requeue_request.
Reported-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Tejun Heo <tj@kernel.org>
[jejb: enhance commend and add commit log for stable] Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use blk_queue_dead() to test whether the queue is dead instead
of !sdev. Since scsi_prep_fn() may be invoked concurrently with
__scsi_remove_device(), keep the queuedata (sdev) pointer in
__scsi_remove_device(). This patch fixes a kernel oops that
can be triggered by USB device removal. See also
http://www.spinics.net/lists/linux-scsi/msg56254.html.
Other changes included in this patch:
- Swap the blk_cleanup_queue() and kfree() calls in
scsi_host_dev_release() to make that code easier to grasp.
- Remove the queue dead check from scsi_run_queue() since the
queue state can change anyway at any point in that function
where the queue lock is not held.
- Remove the queue dead check from the start of scsi_request_fn()
since it is redundant with the scsi_device_online() check.
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Tejun Heo <tj@kernel.org> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...teach scsi_sysfs_add_devices() to check for deleted devices() before
trying to add them, and teach scsi_remove_target() how to remove targets
that have not been added via device_add().
Reported-by: Dariusz Majchrzak <dariusz.majchrzak@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rapid ata hotplug on a libsas controller results in cases where libsas
is waiting indefinitely on eh to perform an ata probe.
A race exists between scsi_schedule_eh() and scsi_restart_operations()
in the case when scsi_restart_operations() issues i/o to other devices
in the sas domain. When this happens the host state transitions from
SHOST_RECOVERY (set by scsi_schedule_eh) back to SHOST_RUNNING and
->host_busy is non-zero so we put the eh thread to sleep even though
->host_eh_scheduled is active.
Before putting the error handler to sleep we need to check if the
host_state needs to return to SHOST_RECOVERY for another trip through
eh. Since i/o that is released by scsi_restart_operations has been
blocked for at least one eh cycle, this implementation allows those
i/o's to run before another eh cycle starts to discourage hung task
timeouts.
Reported-by: Tom Jackson <thomas.p.jackson@intel.com> Tested-by: Tom Jackson <thomas.p.jackson@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 198439e4 [SCSI] libsas: do not set res = 0 in sas_ex_discover_dev()
commit 19252de6 [SCSI] libsas: fix wide port hotplug issues
The above commits seem to have confused the return value of
sas_ex_discover_dev which is non-zero on failure and
sas_ex_join_wide_port which just indicates short circuiting discovery on
already established ports. The result is random discovery failures
depending on configuration.
Calls to sas_ex_join_wide_port are the source of the trouble as its
return value is errantly assigned to 'res'. Convert it to bool and stop
returning its result up the stack.
Tested-by: Dan Melnic <dan.melnic@amd.com> Reported-by: Dan Melnic <dan.melnic@amd.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Jack Wang <jack_wang@usish.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Continue running revalidation until no more broadcast devices are
discovered. Fixes cases where re-discovery completes too early in a
domain with multiple expanders with pending re-discovery events.
Servicing BCNs can get backed up behind error recovery.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to enable the DIU video controller on the P1022DS, the FPGA needs
to be switched to "indirect mode", where the localbus is disabled and
the FPGA is accessed via writes to localbus chip select signals CS0 and CS1.
To obtain the address of CS0 and CS1, the platform driver uses an "indirect
pixis mode" device tree node. This node assumes that the localbus 'ranges'
property is sorted in chip-select order. That is, reg value 0 maps to
CS0, reg value 1 maps to CS1, etc. This is how the 'ranges' property is
supposed to be arranged.
Unfortunately, the 'ranges' property is often mis-arranged, and not just on
the P1022DS. Linux normally does not care, since it does not program the
localbus. But the indirect-mode code on the P1022DS does care.
The "proper" fix is to have U-Boot fix the 'ranges' property, but this would
be too cumbersome. The names and 'reg' properties of all the localbus
devices would also need to be updated, and determining which localbus device
maps to which chip select is board-specific.
Instead, we determine the CS0/CS1 base addresses the same way that U-boot
does -- by reading the BRx registers directly and mapping them to physical
addresses. This code is simpler and more reliable, and it does not require
a U-boot or device tree change.
Since the indirect pixis device tree node is no longer needed, the node is
deleted from the DTS.
Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are seeing an oops in be_get_fw_log_level on ppc64 where we walk
off the end of memory.
commit 941a77d582c8 (be2net: Fix to allow get/set of debug levels in
the firmware.) requires byteswapping of num_modes and num_modules.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Sathya Perla <sperla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function eeh_event_handler() dereferences the pointer returned by
handle_eeh_events() without checking, causing a crash if NULL was
returned, which is expected in some situations.
This patch fixes this bug by checking for the value returned by
handle_eeh_events() before dereferencing it.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For SD hosts using retuning mode 1, when retuning timer expired, it will
need to do retuning in sdhci_request before processing the actual
request. But the retuning command is fixed: cmd19 for SD card and cmd21
for eMMC card, so we can't use the original request's command to do the
tuning.
And since the tuning command depends on the card type attached to the
host, we will need to know the card type to use the correct tuning
command.
Signed-off-by: Aaron Lu <aaron.lu@amd.com> Reviewed-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At http://dev.laptop.org/ticket/11980 we have determined that the
Marvell CaFe SDHCI controller reports bad card presence during
resume. It reports that no card is present even when it is.
This is a regression -- resume worked back around 2.6.37.
Around 400ms after resuming, a "card inserted" interrupt is
generated, at which point it starts reporting presence.
Work around this hardware oddity by setting the
SDHCI_QUIRK_BROKEN_CARD_DETECTION flag.
Thanks to Chris Ball for helping with diagnosis.
Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BTW, speaking of struct file treatment related to sockets -
there's this piece of code in iscsi:
/*
* The SCTP stack needs struct socket->file.
*/
if ((np->np_network_transport == ISCSI_SCTP_TCP) ||
(np->np_network_transport == ISCSI_SCTP_UDP)) {
if (!new_sock->file) {
new_sock->file = kzalloc(
sizeof(struct file), GFP_KERNEL);
For one thing, as far as I can see it'not true - sctp does *not* depend on
socket->file being non-NULL; it does, in one place, check socket->file->f_flags
for O_NONBLOCK, but there it treats NULL socket->file as "flag not set".
Which is the case here anyway - the fake struct file created in
__iscsi_target_login_thread() (and in iscsi_target_setup_login_socket(), with
the same excuse) do *not* get that flag set.
Moreover, it's a bloody serious violation of a bunch of asserts in VFS;
all struct file instances should come from filp_cachep, via get_empty_filp()
(or alloc_file(), which is a wrapper for it). FWIW, I'm very tempted to
do this and be done with the entire mess:
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Andy Grover <agrover@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many SCSI commands are defined to return a CHECK CONDITION / ILLEGAL
REQUEST with ASC set to LOGICAL BLOCK ADDRESS OUT OF RANGE if the
initiator sends a command that accesses a too-big LBA. Add an enum
value and case entries so that target code can return this status.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge emailed kgdb dmesg fixups patches from Anton Vorontsov:
"The dmesg command appears to be broken after the printk rework. The
old logic in the kdb code makes no sense in terms of current
printk/logging storage format, and KDB simply hangs forever upon
entering 'dmesg' command.
The first patch revives the command by switching to kmsg_dumper
iterator. As a side-effect, the code is now much more simpler.
A few changes were needed in the printk.c: we needed unlocked variant
of the kmsg_dumper iterator, but these can surely wait for 3.6.
It's probably too late even for the first patch to go to 3.5, but I'll
try to convince otherwise. :-) Here we go:
- The current code is broken for sure, and has no hope to work at
all. It is a regression
- The new code works for me, and probably works for everyone else;
- If it compiles (and I urge everyone to compile-test it on your
setup), it hardly can make things worse."
* Merge emailed patches from Anton Vorontsov: (4 commits)
kdb: Switch to nolock variants of kmsg_dump functions
printk: Implement some unlocked kmsg_dump functions
printk: Remove kdb_syslog_data
kdb: Revive dmesg command
Anton Vorontsov [Sat, 21 Jul 2012 00:27:37 +0000 (17:27 -0700)]
kdb: Revive dmesg command
The kgdb dmesg command is broken after the printk rework. The old logic
in kdb code makes no sense in terms of current printk/logging storage
format, and KDB simply hangs forever.
This patch revives the command by switching to kmsg_dumper iterator.
The code is now much more simpler and shorter.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull late MIPS fixes from Ralf Baechle:
"This fixes a number of lose ends in the MIPS code and various bug
fixes.
Aside of dropping some patch that should not be in this pull request
everything has sat in -next for quite a while and there are no known
issues.
The biggest patch in this patch set moves the allocation of an array
that is aliased to a function (for runtime generated code) to
assembler code. This avoids an issue with certain toolchains when
building for microMIPS."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (35 commits)
MIPS: PCI: Move fixups from __init to __devinit.
MIPS: Fix bug.h MIPS build regression
MIPS: sync-r4k: remove redundant irq operation
MIPS: smp: Warn on too early irq enable
MIPS: call set_cpu_online() on cpu being brought up with irq disabled
MIPS: call ->smp_finish() a little late
MIPS: Yosemite: delay irq enable to ->smp_finish()
MIPS: SMTC: delay irq enable to ->smp_finish()
MIPS: BMIPS: delay irq enable to ->smp_finish()
MIPS: Octeon: delay enable irq to ->smp_finish()
MIPS: Oprofile: Fix build as a module.
MIPS: BCM63XX: Fix BCM6368 IPSec clock bit
MIPS: perf: Fix build error caused by unused counters_per_cpu_to_total()
MIPS: Fix Magic SysRq L kernel crash.
MIPS: BMIPS: Fix duplicate header inclusion.
mips: mark const init data with __initconst instead of __initdata
MIPS: cmpxchg.h: Add missing include
MIPS: Malta may also be equipped with MIPS64 R2 processors.
MIPS: Fix typo multipy -> multiply
MIPS: Cavium: Fix duplicate ARCH_SPARSEMEM_ENABLE in kconfig.
...
Merge tag 'dm-3.5-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper discard fixes from Alasdair G Kergon:
- avoid a crash in dm-raid1 when discards coincide with mirror
recovery;
- avoid discarding shared data that's still needed in dm-thin;
- don't guarantee that discarded blocks will be wiped in dm-raid1.
* tag 'dm-3.5-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm raid1: set discard_zeroes_data_unsupported
dm thin: do not send discards to shared blocks
dm raid1: fix crash with mirror recovery and discard
Merge branch 'for-linus' of git://git.open-osd.org/linux-open-osd
Pull pnfs/ore fixes from Boaz Harrosh:
"These are catastrophic fixes to the pnfs objects-layout that were just
discovered. They are also destined for @stable.
I have found these and worked on them at around RC1 time but
unfortunately went to the hospital for kidney stones and had a very
slow recovery. I refrained from sending them as is, before proper
testing, and surly I have found a bug just yesterday.
So now they are all well tested, and have my sign-off. Other then
fixing the problem at hand, and assuming there are no bugs at the new
code, there is low risk to any surrounding code. And in anyway they
affect only these paths that are now broken. That is RAID5 in pnfs
objects-layout code. It does also affect exofs (which was not broken)
but I have tested exofs and it is lower priority then objects-layout
because no one is using exofs, but objects-layout has lots of users."
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
pnfs-obj: Fix __r4w_get_page when offset is beyond i_size
pnfs-obj: don't leak objio_state if ore_write/read fails
ore: Unlock r4w pages in exact reverse order of locking
ore: Remove support of partial IO request (NFS crash)
ore: Fix NFS crash by supporting any unaligned RAID IO
and we finally have the fix. I am quite confident the fix is correct
because I could reproduce the problem with nandsim and verify the fix.
It was also verified by Iwo (the reporter).
I am also confident that this is OK to merge the fix so late because
this patch affects only the fixup functionality, which is not used by
most users."
* tag 'upstream-3.5-rc8' of git://git.infradead.org/linux-ubifs:
UBIFS: fix a bug in empty space fix-up
We can't guarantee that REQ_DISCARD on dm-mirror zeroes the data even if
the underlying disks support zero on discard. So this patch sets
ti->discard_zeroes_data_unsupported.
For example, if the mirror is in the process of resynchronizing, it may
happen that kcopyd reads a piece of data, then discard is sent on the
same area and then kcopyd writes the piece of data to another leg.
Consequently, the data is not zeroed.
When process_discard receives a partial discard that doesn't cover a
full block, it sends this discard down to that block. Unfortunately, the
block can be shared and the discard would corrupt the other snapshots
sharing this block.
This patch detects block sharing and ends the discard with success when
sending it to the shared block.
The above change means that if the device supports discard it can't be
guaranteed that a discard request zeroes data. Therefore, we set
ti->discard_zeroes_data_unsupported.
dm raid1: fix crash with mirror recovery and discard
This patch fixes a crash when a discard request is sent during mirror
recovery.
Firstly, some background. Generally, the following sequence happens during
mirror synchronization:
- function do_recovery is called
- do_recovery calls dm_rh_recovery_prepare
- dm_rh_recovery_prepare uses a semaphore to limit the number
simultaneously recovered regions (by default the semaphore value is 1,
so only one region at a time is recovered)
- dm_rh_recovery_prepare calls __rh_recovery_prepare,
__rh_recovery_prepare asks the log driver for the next region to
recover. Then, it sets the region state to DM_RH_RECOVERING. If there
are no pending I/Os on this region, the region is added to
quiesced_regions list. If there are pending I/Os, the region is not
added to any list. It is added to the quiesced_regions list later (by
dm_rh_dec function) when all I/Os finish.
- when the region is on quiesced_regions list, there are no I/Os in
flight on this region. The region is popped from the list in
dm_rh_recovery_start function. Then, a kcopyd job is started in the
recover function.
- when the kcopyd job finishes, recovery_complete is called. It calls
dm_rh_recovery_end. dm_rh_recovery_end adds the region to
recovered_regions or failed_recovered_regions list (depending on
whether the copy operation was successful or not).
The above mechanism assumes that if the region is in DM_RH_RECOVERING
state, no new I/Os are started on this region. When I/O is started,
dm_rh_inc_pending is called, which increases reg->pending count. When
I/O is finished, dm_rh_dec is called. It decreases reg->pending count.
If the count is zero and the region was in DM_RH_RECOVERING state,
dm_rh_dec adds it to the quiesced_regions list.
Consequently, if we call dm_rh_inc_pending/dm_rh_dec while the region is
in DM_RH_RECOVERING state, it could be added to quiesced_regions list
multiple times or it could be added to this list when kcopyd is copying
data (it is assumed that the region is not on any list while kcopyd does
its jobs). This results in memory corruption and crash.
There already exist bypasses for REQ_FLUSH requests: REQ_FLUSH requests
do not belong to any region, so they are always added to the sync list
in do_writes. dm_rh_inc_pending does not increase count for REQ_FLUSH
requests. In mirror_end_io, dm_rh_dec is never called for REQ_FLUSH
requests. These bypasses avoid the crash possibility described above.
These bypasses were improperly implemented for REQ_DISCARD when
the mirror target gained discard support in commit 5fc2ffeabb9ee0fc0e71ff16b49f34f0ed3d05b4 (dm raid1: support discard).
In do_writes, REQ_DISCARD requests is always added to the sync queue and
immediately dispatched (even if the region is in DM_RH_RECOVERING). However,
dm_rh_inc and dm_rh_dec is called for REQ_DISCARD resusts. So it violates the
rule that no I/Os are started on DM_RH_RECOVERING regions, and causes the list
corruption described above.
This patch changes it so that REQ_DISCARD requests follow the same path
as REQ_FLUSH. This avoids the crash.
Boaz Harrosh [Thu, 7 Jun 2012 23:02:30 +0000 (02:02 +0300)]
pnfs-obj: Fix __r4w_get_page when offset is beyond i_size
It is very common for the end of the file to be unaligned on
stripe size. But since we know it's beyond file's end then
the XOR should be preformed with all zeros.
Old code used to just read zeros out of the OSD devices, which is a great
waist. But what scares me more about this situation is that, we now have
pages attached to the file's mapping that are beyond i_size. I don't
like the kind of bugs this calls for.
Fix both birds, by returning a global zero_page, if offset is beyond
i_size.
TODO:
Change the API to ->__r4w_get_page() so a NULL can be
returned without being considered as error, since XOR API
treats NULL entries as zero_pages.
[Bug since 3.2. Should apply the same way to all Kernels since] CC: Stable Tree <stable@kernel.org> Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
ore: Unlock r4w pages in exact reverse order of locking
The read-4-write pages are locked in address ascending order.
But where unlocked in a way easiest for coding. Fix that,
locks should be released in opposite order of locking, .i.e
descending address order.
I have not hit this dead-lock. It was found by inspecting the
dbug print-outs. I suspect there is an higher lock at caller that
protects us, but fix it regardless.
Boaz Harrosh [Fri, 8 Jun 2012 01:30:40 +0000 (04:30 +0300)]
ore: Remove support of partial IO request (NFS crash)
Do to OOM situations the ore might fail to allocate all resources
needed for IO of the full request. If some progress was possible
it would proceed with a partial/short request, for the sake of
forward progress.
Since this crashes NFS-core and exofs is just fine without it just
remove this contraption, and fail.
TODO:
Support real forward progress with some reserved allocations
of resources, such as mem pools and/or bio_sets
[Bug since 3.2 Kernel] CC: Stable Tree <stable@kernel.org> CC: Benny Halevy <bhalevy@tonian.com> Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Boaz Harrosh [Thu, 7 Jun 2012 22:19:07 +0000 (01:19 +0300)]
ore: Fix NFS crash by supporting any unaligned RAID IO
In RAID_5/6 We used to not permit an IO that it's end
byte is not stripe_size aligned and spans more than one stripe.
.i.e the caller must check if after submission the actual
transferred bytes is shorter, and would need to resubmit
a new IO with the remainder.
Exofs supports this, and NFS was supposed to support this
as well with it's short write mechanism. But late testing has
exposed a CRASH when this is used with none-RPC layout-drivers.
The change at NFS is deep and risky, in it's place the fix
at ORE to lift the limitation is actually clean and simple.
So here it is below.
The principal here is that in the case of unaligned IO on
both ends, beginning and end, we will send two read requests
one like old code, before the calculation of the first stripe,
and also a new site, before the calculation of the last stripe.
If any "boundary" is aligned or the complete IO is within a single
stripe. we do a single read like before.
The code is clean and simple by splitting the old _read_4_write
into 3 even parts:
1._read_4_write_first_stripe
2. _read_4_write_last_stripe
3. _read_4_write_execute
And calling 1+3 at the same place as before. 2+3 before last
stripe, and in the case of all in a single stripe then 1+2+3
is preformed additively.
Why did I not think of it before. Well I had a strike of
genius because I have stared at this code for 2 years, and did
not find this simple solution, til today. Not that I did not try.
This solution is much better for NFS than the previous supposedly
solution because the short write was dealt with out-of-band after
IO_done, which would cause for a seeky IO pattern where as in here
we execute in order. At both solutions we do 2 separate reads, only
here we do it within a single IO request. (And actually combine two
writes into a single submission)
NFS/exofs code need not change since the ORE API communicates the new
shorter length on return, what will happen is that this case would not
occur anymore.
hurray!!
[Stable this is an NFS bug since 3.2 Kernel should apply cleanly] CC: Stable Tree <stable@kernel.org> Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
UBIFS has a feature called "empty space fix-up" which is a quirk to work-around
limitations of dumb flasher programs. Namely, of those flashers that are unable
to skip NAND pages full of 0xFFs while flashing, resulting in empty space at
the end of half-filled eraseblocks to be unusable for UBIFS. This feature is
relatively new (introduced in v3.0).
The fix-up routine (fixup_free_space()) is executed only once at the very first
mount if the superblock has the 'space_fixup' flag set (can be done with -F
option of mkfs.ubifs). It basically reads all the UBIFS data and metadata and
writes it back to the same LEB. The routine assumes the image is pristine and
does not have anything in the journal.
There was a bug in 'fixup_free_space()' where it fixed up the log incorrectly.
All but one LEB of the log of a pristine file-system are empty. And one
contains just a commit start node. And 'fixup_free_space()' just unmapped this
LEB, which resulted in wiping the commit start node. As a result, some users
were unable to mount the file-system next time with the following symptom:
UBIFS error (pid 1): replay_log_leb: first log node at LEB 3:0 is not CS node
UBIFS error (pid 1): replay_log_leb: log error detected while replaying the log at LEB 3:0
The root-cause of this bug was that 'fixup_free_space()' wrongly assumed
that the beginning of empty space in the log head (c->lhead_offs) was known
on mount. However, it is not the case - it was always 0. UBIFS does not store
in it the master node and finds out by scanning the log on every mount.
The fix is simple - just pass commit start node size instead of 0 to
'fixup_leb()'.
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull last minute Ceph fixes from Sage Weil:
"The important one fixes a bug in the socket failure handling behavior
that was turned up in some recent failure injection testing. The
other two are minor bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: endian bug in rbd_req_cb()
rbd: Fix ceph_snap_context size calculation
libceph: fix messenger retry
Merge tag 'md-3.5-fixes' of git://neil.brown.name/md
Pull three md bugfixes from NeilBrown:
"One of the bugs was introduced in 3.5-rc1. Others have been there for
longer."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md/raid1: close some possible races on write errors during resync
md: avoid crash when stopping md array races with closing other open fds.
md: fix bug in handling of new_data_offset
Pull networking changes from David Miller:
"Ok, we should be good to go now"
1) We have to statically initialize the init_net device list head rather
than do so in an initcall, otherwise netprio_cgroup crashes if it's
built statically rather than modular (Mark D. Rustad)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Statically initialize init_net.dev_base_head
MAINTAINERS: Changes in qlcnic and qlge maintainers list
cipso: don't follow a NULL pointer when setsockopt() is called
Merge branch 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID update from Jiri Kosina:
"A final round of changes for HID for 3.5: just device ID additions."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-multitouch: add support for Zytronic panels
HID: add Sennheiser BTD500USB device support
HID: add battery quirk for Apple Wireless ANSI
The strcpy was being used to set the name of the board. Since the
destination char* was read-only and the name is set statically at
compile time; this was both wrong and redundant.
The type of char* is changed to const char* to prevent future errors.
Reported-by: Radek Masin <radek@masin.eu> Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
[ Taking directly due to vacations - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixups are executed once the pci-device is found which is during boot
process so __init seems fine as long as the platform does not support
hotplug.
However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.
[ralf@linux-mips.org: Made piixirqmap[] in malta_piix_func0_fixup()
__initdata.]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> Cc: linux-mips@linux-mips.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/kernel/machine_kexec.o
In file included from include/linux/kernel.h:20:0,
from include/asm-generic/bug.h:35,
from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bug.h:41,
from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:20,
from include/linux/bitops.h:22,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/linux/log2.h: In function '__ilog2_u32':
include/linux/log2.h:34:2: error: implicit declaration of function 'fls' [-Werror=implicit-function-declaration]
include/linux/log2.h: In function '__ilog2_u64':
include/linux/log2.h:42:2: error: implicit declaration of function 'fls64' [-Werror=implicit-function-declaration]
include/linux/log2.h: In function '__roundup_pow_of_two':
include/linux/log2.h:63:2: error: implicit declaration of function 'fls_long' [-Werror=implicit-function-declaration]
In file included from include/linux/bitops.h:22:0,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
/home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h: At top level:
/home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:615:19: error: static declaration of 'fls' follows non-static declaration
include/linux/log2.h:34:9: note: previous implicit declaration of 'fls' was here
In file included from /home/yuasa/src/linux/kernel/git/linux-2.6/arch/mips/include/asm/bitops.h:651:0,
from include/linux/bitops.h:22,
from include/linux/signal.h:38,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/asm-generic/bitops/fls64.h:18:28: error: static declaration of 'fls64' follows non-static declaration
include/linux/log2.h:42:9: note: previous implicit declaration of 'fls64' was here
In file included from include/linux/signal.h:38:0,
from include/linux/elfcore.h:5,
from include/linux/kexec.h:60,
from arch/mips/kernel/machine_kexec.c:9:
include/linux/bitops.h:160:24: error: conflicting types for 'fls_long'
include/linux/log2.h:63:16: note: previous implicit declaration of 'fls_long' was here
cc1: all warnings being treated as errors
MIPS: call set_cpu_online() on cpu being brought up with irq disabled
To prevent a problem as commit 5fbd036b [sched: Cleanup cpu_active madness]
and commit 2baab4e9 [sched: Fix select_fallback_rq() vs cpu_active/cpu_online]
try to resolve, move set_cpu_online() to the brought up CPU and with irq
disabled.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com> Cc: Sergei Shtylyov <sshtylyov@mvista.com> Cc: David Daney <david.daney@cavium.com> Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3851/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have move irq enable to ->smp_finish. Place ->smp_finish() a little
late to prepare for move set_cpu_online() into start_secondary.
And it's not necessary to call cpu_set(cpu, cpu_callin_map) and
synchronise_count_slave() with irq enabled.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com> Cc: Sergei Shtylyov <sshtylyov@mvista.com> Cc: David Daney <david.daney@cavium.com> Acked-by: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3850/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When building oprofile as a module for R10000 or R7000 class processors,
E9000 or MIPSxx class cores since 3572a2c37f667ee49333f8863722b8f43eac506b
[MIPS: make oprofile use cp0_perfcount_irq if it is set] an
MIPS: perf: Fix build error caused by unused counters_per_cpu_to_total()
cc1: warnings being treated as errors
arch/mips/kernel/perf_event_mipsxx.c:166: error: 'counters_per_cpu_to_total' defined but not used
make[2]: *** [arch/mips/kernel/perf_event_mipsxx.o] Error 1
make[2]: *** Waiting for unfinished jobs....
Vincent Wen [Thu, 19 Jul 2012 07:11:16 +0000 (09:11 +0200)]
MIPS: Fix Magic SysRq L kernel crash.
show_backtrace() was passed a NULL pointer which caused paging
request fail. Set to current task as other architectures (ARM,
etc) do when passed a NULL task pointer.
mips: mark const init data with __initconst instead of __initdata
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Aaro Koskinen [Thu, 19 Jul 2012 07:11:15 +0000 (09:11 +0200)]
MIPS: cmpxchg.h: Add missing include
Fix the following build breakage in v3.4-rc1:
CC kernel/irq_work.o
In file included from include/linux/irq_work.h:4:0,
from kernel/irq_work.c:10:
include/linux/llist.h: In function 'llist_del_all':
include/linux/llist.h:178:2: error: implicit declaration of function 'BUILD_BUG_ON' [-Werror=implicit-function-declaration]
Leonid Yegoshin [Thu, 19 Jul 2012 07:11:15 +0000 (09:11 +0200)]
MIPS: Malta may also be equipped with MIPS64 R2 processors.
Signed-off-by: Leonid Yegoshin <yegoshin@mips.com> Signed-off-by: Steven J. Hill <sjhill@mips.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3792/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Steven J. Hill [Thu, 19 Jul 2012 07:11:14 +0000 (09:11 +0200)]
MIPS: Malta: Change start address to avoid conflicts.
There are ACPI and SMB devices in the 0x1000..0x1fff address range.
Signed-off-by: Steven J. Hill <sjhill@mips.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3581/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Leonid Yegoshin [Thu, 19 Jul 2012 07:11:14 +0000 (09:11 +0200)]
MIPS: Fix race condition with FPU thread task flag during context switch.
[ralf@linux-mips.org: Cosmetic changes; also fixed up r2300_switch.S and
octeon_switch.S which needed similar modifications.]
Signed-off-by: Leonid Yegoshin <yegoshin@mips.com> Signed-off-by: Steven J. Hill <sjhill@mips.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3784/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Douglas Leung [Thu, 19 Jul 2012 07:11:13 +0000 (09:11 +0200)]
MIPS: Fix decoding of c0_config1 for MIPSxx caches with 32 ways per set.
This affects certain 4Kc cores.
Signed-off-by: Douglas Leung <douglas@mips.com> Signed-off-by: Steven J. Hill <sjhill@mips.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3855/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Steven J. Hill [Fri, 6 Jul 2012 19:56:01 +0000 (21:56 +0200)]
MIPS: Refactor 'clear_page' and 'copy_page' functions.
Remove usage of the '__attribute__((alias("...")))' hack that aliased
to integer arrays containing micro-assembled instructions. This hack
breaks when building a microMIPS kernel. It also makes the code much
easier to understand.
[ralf@linux-mips.org: Added back export of the clear_page and copy_page
symbols so certain modules will work again. Also fixed build with
CONFIG_SIBYTE_DMA_PAGEOPS enabled.]
Signed-off-by: Steven J. Hill <sjhill@mips.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3866/ Acked-by: David Daney <david.daney@cavium.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Leonid Yegoshin [Fri, 6 Jul 2012 19:56:01 +0000 (21:56 +0200)]
MIPS: Don't panic on 5KEc.
It's a bloody bog standard MIPS64R2 core with just a new PrId ID. Iow
that essentially means Linux just panics because it doesn't know how to
name the core.
[ralf@linux-mips.org: Split original patch into several smaller patches.]
Signed-off-by: Leonid Yegoshin <yegoshin@mips.com> Signed-off-by: Steven J. Hill <sjhill@mips.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3792/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Added a 'reschedule_retry' call possibility at the end of
end_sync_write, but didn't add matching code at the end of
sync_request_write. So if the writes complete very quickly, or
scheduling makes it seem that way, then we can miss rescheduling
the request and the resync could hang.
md: avoid crash when stopping md array races with closing other open fds.
md will refuse to stop an array if any other fd (or mounted fs) is
using it.
When any fs is unmounted of when the last open fd is closed all
pending IO will be flushed (e.g. sync_blockdev call in __blkdev_put)
so there will be no pending IO to worry about when the array is
stopped.
However in order to send the STOP_ARRAY ioctl to stop the array one
must first get and open fd on the block device.
If some fd is being used to write to the block device and it is closed
after mdadm open the block device, but before mdadm issues the
STOP_ARRAY ioctl, then there will be no last-close on the md device so
__blkdev_put will not call sync_blockdev.
If this happens, then IO can still be in-flight while md tears down
the array and bad things can happen (use-after-free and subsequent
havoc).
So in the case where do_md_stop is being called from an open file
descriptor, call sync_block after taking the mutex to ensure there
will be no new openers.
This is needed when setting a read-write device to read-only too.
introduced a 'new_data_offset' attribute which should normally
be the same as 'data_offset', but can be explicitly set to a different
value to allow a reshape operation to move the data.
Unfortunately when the 'data_offset' is explicitly set through
sysfs, the new_data_offset is not also set, so the two would become
out-of-sync incorrectly.
One result of this is that trying to set the 'size' after the
'data_offset' would fail because it is not permitted to set the size
when the 'data_offset' and 'new_data_offset' are different - as that
can be confusing.
Consequently when mdadm tried to do this while assembling an IMSM
array it would fail.
This bug was introduced in 3.5-rc1.
Reported-by: Brian Downing <bdowning@lavos.net> Bisected-by: Brian Downing <bdowning@lavos.net> Tested-by: Brian Downing <bdowning@lavos.net> Signed-off-by: NeilBrown <neilb@suse.de>
Pull target fixes from Nicholas Bellinger:
"This includes a bugfix from MDR to address a NULL pointer OOPs with
FCoE aborts, along with a WRITE_SAME emulation bugfix for NOLB=0
cases, and persistent reservation return cleanups from Roland.
All three patches are CC'ed to stable."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix range calculation in WRITE SAME emulation when num blocks == 0
target: Clean up returning errors in PR handling code
tcm_fc: Fix crash seen with aborts and large reads
Commit 377780887 ("bug.h: need linux/kernel.h for TAINT_WARN.") broke
all MIPS builds:
CC arch/mips/kernel/machine_kexec.o
include/linux/log2.h: In function '__ilog2_u32':
include/linux/log2.h:34:2: error: implicit declaration of function 'fls' [-Werror=implicit-function-declaration]
include/linux/log2.h: In function '__ilog2_u64':
include/linux/log2.h:42:2: error: implicit declaration of function 'fls64' [-Werror=implicit-function-declaration]
...
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org> Tested-by: John Crispin <blogic@openwrt.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: David Daney <ddaney@caviumnetworks.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make wait_for_device_probe() also do scsi_complete_async_scans()
Commit a7a20d103994 ("sd: limit the scope of the async probe domain")
make the SCSI device probing run device discovery in it's own async
domain.
However, as a result, the partition detection was no longer synchronized
by async_synchronize_full() (which, despite the name, only synchronizes
the global async space, not all of them). Which in turn meant that
"wait_for_device_probe()" would not wait for the SCSI partitions to be
parsed.
And "wait_for_device_probe()" was what the boot time init code relied on
for mounting the root filesystem.
Now, most people never noticed this, because not only is it
timing-dependent, but modern distributions all use initrd. So the root
filesystem isn't actually on a disk at all. And then before they
actually mount the final disk filesystem, they will have loaded the
scsi-wait-scan module, which not only does the expected
wait_for_device_probe(), but also does scsi_complete_async_scans().
[ Side note: scsi_complete_async_scans() had also been partially broken,
but that was fixed in commit 43a8d39d0137 ("fix async probe
regression"), so that same commit a7a20d103994 had actually broken
setups even if you used scsi-wait-scan explicitly ]
Solve this problem by just moving the scsi_complete_async_scans() call
into wait_for_device_probe(). Everybody who wants to wait for device
probing to finish really wants the SCSI probing to complete, so there's
no reason not to do this.
So now "wait_for_device_probe()" really does what the name implies, and
properly waits for device probing to finish. This also removes the now
unnecessary extra calls to scsi_complete_async_scans().
Reported-and-tested-by: Artem S. Tashkinov <t.artem@mailcity.com> Cc: Dan Williams <dan.j.williams@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: James Bottomley <jbottomley@parallels.com> Cc: Borislav Petkov <bp@amd64.org> Cc: linux-scsi <linux-scsi@vger.kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull SELinux regression fixes from James Morris.
Andrew Morton has a box that hit that open perms problem.
I also renamed the "epollwakeup" selinux name for the new capability to
be "block_suspend", to match the rename done by commit d9914cf66181
("PM: Rename CAP_EPOLLWAKEUP to CAP_BLOCK_SUSPEND").
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
SELinux: do not check open perms if they are not known to policy
SELinux: include definition of new capabilities
Hans Verkuil [Wed, 11 Jul 2012 12:12:45 +0000 (14:12 +0200)]
v4l2-dev: forgot to add VIDIOC_DV_TIMINGS_CAP.
The VIDIOC_DV_TIMINGS_CAP ioctl check wasn't added to determine_valid_ioctls().
This caused this ioctl to always return -ENOTTY.
The cause for this was that for 3.5 two patch series were merged, one
changing V4L2 core ioctl handling and one adding new functionality, and
some of the new functionality wasn't handled by the new V4L2 core code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[ Taking it directly due to vacations - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes for SPEAr from Olof Johansson:
"These are arriving very late in the release cycle, but there has been
a change of maintainers on the SPEAr platform and they have needed a
while to get going.
The patch count is higher than I would like at this point, but they're
all relevant fixes and well-contained in their own platform code. I
still think it's suitable 3.5 material and I don't think it should
increase the need for a -rc8 since they are so contained."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SPEAr600: Fix timer interrupt definition in spear600.dtsi
ARM: dts: SPEAr320: Boot the board in EXTENDED_MODE
ARM: dts: SPEAr320: Fix compatible string
Clk: SPEAr1340: Update sys clock parent array
clk: SPEAr1340: Fix clk enable register for uart1 and i2c1.
ARM: SPEAr13xx: Fix Interrupt bindings
Clk:spear6xx:Fix: Rename clk ids within predefined limit
Clk:spear3xx:Fix: Rename clk ids within predefined limit
clk:spear1310:Fix: Rename clk ids within predefined limit
clk:spear1340:Fix: Rename clk ids within predefined limit
* git://git.samba.org/sfrench/cifs-2.6:
cifs: always update the inode cache with the results from a FIND_*
cifs: when CONFIG_HIGHMEM is set, serialize the read/write kmaps
cifs: on CONFIG_HIGHMEM machines, limit the rsize/wsize to the kmap space
Initialise mid_q_entry before putting it on the pending queue
Paul Moore [Tue, 17 Jul 2012 11:07:47 +0000 (11:07 +0000)]
cipso: don't follow a NULL pointer when setsockopt() is called
As reported by Alan Cox, and verified by Lin Ming, when a user
attempts to add a CIPSO option to a socket using the CIPSO_V4_TAG_LOCAL
tag the kernel dies a terrible death when it attempts to follow a NULL
pointer (the skb argument to cipso_v4_validate() is NULL when called via
the setsockopt() syscall).
This patch fixes this by first checking to ensure that the skb is
non-NULL before using it to find the incoming network interface. In
the unlikely case where the skb is NULL and the user attempts to add
a CIPSO option with the _TAG_LOCAL tag we return an error as this is
not something we want to allow.
A simple reproducer, kindly supplied by Lin Ming, although you must
have the CIPSO DOI #3 configure on the system first or you will be
caught early in cipso_v4_validate():
CC: Lin Ming <mlin@ss.pku.edu.cn> Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log