Uwe Kleine-König [Wed, 16 Dec 2009 16:10:09 +0000 (17:10 +0100)]
ASoC: sh: FSI:: don't check platform_get_irq's return value against zero
platform_get_irq returns -ENXIO on failure, so !irq was probably
always true. Better use (int)irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
Krzysztof Helt [Sat, 19 Dec 2009 17:31:04 +0000 (18:31 +0100)]
ALSA: fix incorrect rounding direction in snd_interval_ratnum()
The direction of rounding is incorrect in the snd_interval_ratnum()
It was detected with following parameters (sb8 driver playing
8kHz stereo file):
- num is always 1000000
- requested frequency rate is from 7999 to 7999 (single frequency)
The first loop calculates div_down(num, freq->min) which is 125.
Thus, a frequency range's minimum value is 1000000 / 125 = 8000 Hz.
The second loop calculates div_up(num, freq->max) which is 126
The frequency range's maximum value is 1000000 / 126 = 7936 Hz.
The range maximum is lower than the range minimum so the function
fails due to empty result range.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hector Martin [Sun, 20 Dec 2009 21:51:31 +0000 (22:51 +0100)]
ALSA: HDA: add powersaving hook for Realtek
The current Realtek code makes no specific provision for turning stuff
off. The codec chip is placed into low-power mode generically, but this
doesn't turn off any external hardware connected to it, in particular
external amplifiers.
This patch creates a hook function that is called by the codec
suspend/resume functions. It ought to disable any external hardware in a
device-specific way. I've implemented a generic ALC889 function that
sets the EAPD pin properly, and used it for the Acer Aspire 8930G which
can benefit from this feature.
On my laptop, this results in ~0.5W extra savings.
Signed-off-by: Hector Martin <hector@marcansoft.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hector Martin [Sun, 20 Dec 2009 21:51:18 +0000 (22:51 +0100)]
ALSA: HDA: simplify Aspire 8930G verb array
This patch just simplifies the 8930G verb array a bit. Just use the
common ALC889 EAPD verb array to make things more consistent. The file
is already huge enough already.
Signed-off-by: Hector Martin <hector@marcansoft.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Russell King [Fri, 18 Dec 2009 17:48:35 +0000 (17:48 +0000)]
ALSA: AACI: simplify codec rate information
There's no need for a specific rule; ALSA's generic AC'97 support
calculates the necessary rate constraint information itself, and
we can use this directly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Takashi Iwai <tiwai@suse.de>
When allocating the PCM buffer, use vmalloc_user() instead of vmalloc().
Otherwise, it would be possible for applications to play the previous
contents of the kernel memory to the speakers, or to read it directly if
the buffer is exported to userspace.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Fri, 18 Dec 2009 01:00:20 +0000 (17:00 -0800)]
Merge branch 'cpumask-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus
* 'cpumask-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
cpumask: rename tsk_cpumask to tsk_cpus_allowed
cpumask: don't recommend set_cpus_allowed hack in Documentation/cpu-hotplug.txt
cpumask: avoid dereferencing struct cpumask
cpumask: convert drivers/idle/i7300_idle.c to cpumask_var_t
cpumask: use modern cpumask style in drivers/scsi/fcoe/fcoe.c
cpumask: avoid deprecated function in mm/slab.c
cpumask: use cpu_online in kernel/perf_event.c
Linus Torvalds [Fri, 18 Dec 2009 00:58:26 +0000 (16:58 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
Keys: KEYCTL_SESSION_TO_PARENT needs TIF_NOTIFY_RESUME architecture support
NOMMU: Optimise away the {dac_,}mmap_min_addr tests
security/min_addr.c: make init_mmap_min_addr() static
keys: PTR_ERR return of wrong pointer in keyctl_get_security()
Linus Torvalds [Fri, 18 Dec 2009 00:57:49 +0000 (16:57 -0800)]
Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
OMAP3: serial - fix bug introduced in
mfd: twl: fix twl4030 rename for remaining driver, board files
USB ehci: replace mach header with plat
omap3: Allow EHCI to be built on OMAP3
Linus Torvalds [Fri, 18 Dec 2009 00:48:08 +0000 (16:48 -0800)]
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (w83627hf) Fix for "No such device"
hwmon: (sht15) Off-by-one error in array index + incorrect constants
hwmon: Add driver for VIA CPU core temperature
hwmon: (smsc47m1) Enable device if needed
hwmon: (smsc47m1) Fail module loading on error
hwmon: (smsc47m1) Only request I/O ports we really use
hwmon: New driver for AMD Family 10h/11h CPUs
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (40 commits)
[SCSI] 3w-9xxx fix bug in sgl loading
[SCSI] fcoe, libfc: adds enable/disable for fcoe interface
[SCSI] libfc: reduce hold time on SCSI host lock
[SCSI] libfc: remote port gets stuck in restart state without really restarting
[SCSI] pm8001: misc code cleanup
[SCSI] pm8001: enable read HBA SAS address from VPD
[SCSI] pm8001: do not reset local sata as it will not be found if reset
[SCSI] pm8001: bit set pm8001_ha->flags
[SCSI] pm8001:fix potential NULL pointer dereference
[SCSI] pm8001: set SSC down-spreading only to get less errors on some 6G device.
[SCSI] pm8001: fix endian issues with SAS address
[SCSI] pm8001: enhance error handle for IO patch
[SCSI] pm8001: Fix for sata io circular lock dependency.
[SCSI] hpsa: add driver for HP Smart Array controllers.
[SCSI] cxgb3i: always use negative errno in case of error
[SCSI] bnx2i: minor code cleanup and update driver version
[SCSI] bnx2i: Task management ABORT TASK fixes
[SCSI] bnx2i: update CQ arming algorith for 5771x chipsets
[SCSI] bnx2i: Adjust sq_size module parametr to power of 2 only if a non-zero value is specified
[SCSI] bnx2i: Add 5771E device support to bnx2i driver
...
Linus Torvalds [Fri, 18 Dec 2009 00:38:06 +0000 (16:38 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (71 commits)
MIPS: Lasat: Fix botched changes to sysctl code.
RTC: rtc-cmos.c: Fix warning on MIPS
MIPS: Cleanup random differences beween lmo and Linus' kernel.
MIPS: No longer hardwire CONFIG_EMBEDDED to y
MIPS: Fix and enhance built-in kernel command line
MIPS: eXcite: Remove platform.
MIPS: Loongson: Cleanups of serial port support
MIPS: Lemote 2F: Suspend CS5536 MFGPT Timer
MIPS: Excite: move iodev_remove to .devexit.text
MIPS: Lasat: Convert to proc_fops / seq_file
MIPS: Cleanup signal code initialization
MIPS: Modularize COP2 handling
MIPS: Move EARLY_PRINTK to Kconfig.debug
MIPS: Yeeloong 2F: Cleanup reset logic using the new ec_write function
MIPS: Yeeloong 2F: Add LID open event as the wakeup event
MIPS: Yeeloong 2F: Add basic EC operations
MIPS: Move several variables from .bss to .init.data
MIPS: Tracing: Make function graph tracer work with -mmcount-ra-address
MIPS: Tracing: Reserve $12(t0) for mcount-ra-address of gcc 4.5
MIPS: Tracing: Make ftrace for MIPS work without -fno-omit-frame-pointer
...
Linus Torvalds [Fri, 18 Dec 2009 00:01:03 +0000 (16:01 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: make sure fallocate properly starts a transaction
Btrfs: make metadata chunks smaller
Btrfs: Show discard option in /proc/mounts
Btrfs: deny sys_link across subvolumes.
Btrfs: fail mount on bad mount options
Btrfs: don't add extent 0 to the free space cache v2
Btrfs: Fix per root used space accounting
Btrfs: Fix btrfs_drop_extent_cache for skip pinned case
Btrfs: Add delayed iput
Btrfs: Pass transaction handle to security and ACL initialization functions
Btrfs: Make truncate(2) more ENOSPC friendly
Btrfs: Make fallocate(2) more ENOSPC friendly
Btrfs: Avoid orphan inodes cleanup during committing transaction
Btrfs: Avoid orphan inodes cleanup while replaying log
Btrfs: Fix disk_i_size update corner case
Btrfs: Rewrite btrfs_drop_extents
Btrfs: Add btrfs_duplicate_item
Btrfs: Avoid superfluous tree-log writeout
Linus Torvalds [Fri, 18 Dec 2009 00:00:19 +0000 (16:00 -0800)]
Merge branch 'kmemleak' of git://linux-arm.org/linux-2.6
* 'kmemleak' of git://linux-arm.org/linux-2.6:
kmemleak: fix kconfig for crc32 build error
kmemleak: Reduce the false positives by checking for modified objects
kmemleak: Show the age of an unreferenced object
kmemleak: Release the object lock before calling put_object()
kmemleak: Scan the _ftrace_events section in modules
kmemleak: Simplify the kmemleak_scan_area() function prototype
kmemleak: Do not use off-slab management with SLAB_NOLEAKTRACE
Linus Torvalds [Thu, 17 Dec 2009 23:59:05 +0000 (15:59 -0800)]
Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
spi: spi_txx9.c: use resource_size()
spi: spi_sh_sci.c: use resource_size()
spi: spi_mpc8xxx.c: use resource_size()
spi: spi_bfin5xx.c: use resource_size()
spi: atmel_spi.c: use resource_size()
spi: Add s3c64xx SPI Controller driver
atmel_spi: fix dma addr calculation for len > BUFFER_SIZE
spi_s3c24xx: add FIQ pseudo-DMA support
spi: controller driver for Designware SPI core
spidev: add proper section markers
spidev: use DECLARE_BITMAP instead of declaring the array
Linus Torvalds [Thu, 17 Dec 2009 23:58:07 +0000 (15:58 -0800)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: mbp_nvidia_bl - add two more MacBookPro variants
backlight: Pass device through notify callback in the pwm driver
backlight: PTR_ERR return of wrong pointer in cr_backlight_probe()
backlight: Constify struct backlight_ops
backlight/thinkpad-acpi: issue backlight class events
Fix up trivial conflicts in thinkpad-acpi support (backlight support
already merged earlier).
Linus Torvalds [Thu, 17 Dec 2009 23:55:08 +0000 (15:55 -0800)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: leds-pwm: Set led_classdev max_brightness
leds: leds-lp3944.h - remove unneeded includes
leds: use default-on trigger for Cobalt Qube
leds: drivers/leds/leds-ss4200.c: fix return statement
leds: leds-pca9532.h- indent with tabs, not spaces
leds: Add LED class driver for regulator driven LEDs.
leds: leds-cobalt-qube.c: use resource_size()
leds: leds-cobalt-raq.c - use resource_size()
leds: Add driver for ADP5520/ADP5501 MFD PMICs
leds: Add driver for LT3593 controlled LEDs
leds-ss4200: Check pci_enable_device return
leds: leds-alix2c - take port address from MSR
leds: LED driver for Intel NAS SS4200 series (v5)
Linus Torvalds [Thu, 17 Dec 2009 23:53:41 +0000 (15:53 -0800)]
Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
PCMCIA: fix pxa2xx_lubbock modular build error
[ARM] Update mach-types
[ARM] pxa: fix no reference of cpu_is_pxa25x() in devices.c
[ARM] pxa/cm-x300: add PWM backlight support
revert "[ARM] pxa/cm-x300: add PWM backlight support"
ARM: use flush_kernel_dcache_area() for dmabounce
ARM: add size argument to __cpuc_flush_dcache_page
ARM: 5848/1: kill flush_ioremap_region()
ARM: cache-l2x0: make better use of background cache handling
ARM: cache-l2x0: avoid taking spinlock for every iteration
[ARM] Kirkwood: Add LaCie Network Space v2 support
ARM: dove: fix the mm mmu flags of the pj4 procinfo
Randy Dunlap [Thu, 17 Dec 2009 23:27:27 +0000 (15:27 -0800)]
printk: fix new kernel-doc warnings
Fix kernel-doc warnings in printk.c:
Warning(kernel/printk.c:1422): No description found for parameter 'dumper'
Warning(kernel/printk.c:1422): Excess function parameter 'dump' description in 'kmsg_dump_register'
Warning(kernel/printk.c:1451): No description found for parameter 'dumper'
Warning(kernel/printk.c:1451): Excess function parameter 'dump' description in 'kmsg_dump_unregister'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hisashi Hifumi [Thu, 17 Dec 2009 23:27:26 +0000 (15:27 -0800)]
readahead: add blk_run_backing_dev
I added blk_run_backing_dev on page_cache_async_readahead so readahead I/O
is unpluged to improve throughput on especially RAID environment.
The normal case is, if page N become uptodate at time T(N), then T(N) <=
T(N+1) holds. With RAID (and NFS to some degree), there is no strict
ordering, the data arrival time depends on runtime status of individual
disks, which breaks that formula. So in do_generic_file_read(), just
after submitting the async readahead IO request, the current page may well
be uptodate, so the page won't be locked, and the block device won't be
implicitly unplugged:
if (PageReadahead(page))
page_cache_async_readahead()
if (!PageUptodate(page))
goto page_not_up_to_date;
//...
page_not_up_to_date:
lock_page_killable(page);
Therefore explicit unplugging can help.
Following is the test result with dd.
#dd if=testdir/testfile of=/dev/null bs=16384
-2.6.30-rc6 1048576+0 records in 1048576+0 records out 17179869184 bytes (17 GB) copied, 224.182 seconds, 76.6 MB/s
-2.6.30-rc6-patched 1048576+0 records in 1048576+0 records out 17179869184 bytes (17 GB) copied, 206.465 seconds, 83.2 MB/s
(7Disks RAID-0 Array)
-2.6.30-rc6 1054976+0 records in 1054976+0 records out 17284726784 bytes (17 GB) copied, 212.233 seconds, 81.4 MB/s
-2.6.30-rc6-patched 1054976+0 records out 17284726784 bytes (17 GB) copied, 198.878 seconds, 86.9 MB/s
(7Disks RAID-5 Array)
The patch was found to improve performance with the SCST scsi target
driver. See
http://sourceforge.net/mailarchive/forum.php?thread_name=a0272b440906030714g67eabc5k8f847fb1e538cc62%40mail.gmail.com&forum_name=scst-devel
Anton Vorontsov [Thu, 17 Dec 2009 23:27:23 +0000 (15:27 -0800)]
rtc: set wakeup capability for I2C and SPI RTC drivers
RTC core won't allow wakeup alarms to be set if RTC devices' parent (i.e.
i2c_client or spi_device) isn't wakeup capable.
For I2C devices there is I2C_CLIENT_WAKE flag exists that we can pass via
board info, and if set, I2C core will initialize wakeup capability. For
SPI devices there is no such flag at all.
I believe that it's not platform code responsibility to allow or disallow
wakeups, instead, drivers themselves should set the capability if a device
can trigger wakeups.
That's what drivers/base/power/sysfs.c says:
* It is the responsibility of device drivers to enable (or disable)
* wakeup signaling as part of changing device power states, respecting
* the policy choices provided through the driver model.
I2C and SPI RTC devices send wakeup events via interrupt lines, so we
should set the wakeup capability if IRQ is routed.
Ideally we should also check irq for wakeup capability before setting
device's capability, i.e.
if (can_irq_wake(irq))
device_set_wakeup_capable(&client->dev, 1);
But there is no can_irq_wake() call exist, and it is not that trivial to
implement it for all interrupts controllers and complex/cascaded setups.
drivers/base/power/sysfs.c also covers these cases:
* Devices may not be able to generate wakeup events from all power
* states. Also, the events may be ignored in some configurations;
* for example, they might need help from other devices that aren't
* active
So there is no guarantee that wakeup will actually work, and so I think
there is no point in being pedantic wrt checking IRQ wakeup capability.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Albert Herranz [Thu, 17 Dec 2009 23:27:20 +0000 (15:27 -0800)]
sdhci-of: reorganize driver to support additional hardware
This patch breaks down sdhci-of into a core portion and a eSDHC portion,
clearing the path to easily support additional hardware using the same OF
driver.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to accurately track how many SDIO functions have been initialised
(and keep card->sdio_funcs in sync) so that we don't try to remove more
functions than we initialised if we hit the error path in
mmc_attach_sdio().
Without this patch if we hit the error path in mmc_attach_sdio() we run
the risk of deferencing invalid memory in sdio_remove_func(), leading to a
crash.
Signed-off-by: Matt Fleming <matt@console-pimps.org> Cc: Daniel Drake <dsd@laptop.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Drake [Thu, 17 Dec 2009 23:27:17 +0000 (15:27 -0800)]
sdio: fix reference counting in sdio_remove_func()
sdio_remove_func() needs to be more careful about reference counting. It
can be called in error paths where sdio_add_func() has never been called
e.g. mmc_attach_sdio error path --> mmc_sdio_remove --> sdio_remove_func
Signed-off-by: Daniel Drake <dsd@laptop.org> Reviewed-by: Matt Fleming <matt@console-pimps.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Oleg Nesterov [Thu, 17 Dec 2009 23:27:15 +0000 (15:27 -0800)]
do_wait() optimization: do not place sub-threads on task_struct->children list
Thanks to Roland who pointed out de_thread() issues.
Currently we add sub-threads to ->real_parent->children list. This buys
nothing but slows down do_wait().
With this patch ->children contains only main threads (group leaders).
The only complication is that forget_original_parent() should iterate over
sub-threads by hand, and de_thread() needs another list_replace() when it
changes ->group_leader.
Henceforth do_wait_thread() can never see task_detached() && !EXIT_DEAD
tasks, we can remove this check (and we can unify do_wait_thread() and
ptrace_do_wait()).
This change can confuse the optimistic search in mm_update_next_owner(),
but this is fixable and minor.
Perhaps badness() and oom_kill_process() should be updated, but they
should be fixed in any case.
Uwe Kleine-König [Thu, 17 Dec 2009 23:27:12 +0000 (15:27 -0800)]
lib/vsprintf.c: document more vsnprintf extensions
These were added in
9ac6e44 (lib/vsprintf.c: add %pU to print UUID/GUIDs) c7dabef (vsprintf: use %pR, %pr instead of %pRt, %pRf) 8a27f7c (lib/vsprintf.c: Add "%pI6c" - print pointer as compressed ipv6 address) 4aa9960 (printk: add %I4, %I6, %i4, %i6 format specifiers) dd45c9c (printk: add %pM format specifier for MAC addresses)
but only added comments to pointer() not vsnprintf() that is refered to by
printk's comments.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Harvey Harrison <harvey.harrison@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joe Perches <joe@perches.com> Cc: Jens Rosenboom <jens@mcbone.net> Cc: David S. Miller <davem@davemloft.net> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Kara [Thu, 17 Dec 2009 23:27:06 +0000 (15:27 -0800)]
reiserfs: truncate blocks not used by a write
It can happen that write does not use all the blocks allocated in
write_begin either because of some filesystem error (like ENOSPC) or
because page with data to write has been removed from memory. We truncate
these blocks so that we don't have dangling blocks beyond i_size.
Cc: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"I think I gave a good enough arguments to not merge it.
To iterate:
* patch makes impossible to start using ext3 on EXT3_FS=n kernels
without reboot.
* this is done only for one pointer on task_struct"
None of config options which define task_struct are tristate directly
or effectively."
"it's dependent on a lot of other stuff not currently in mainline
and badly broken with current fs/namespace.c. Sorry, badly
out-of-order cherry-pick from old queue.
PS: there's a large pending series reworking the refcounting and
lifetime rules for vfsmounts that will, among other things, allow to
rip a subtree away _without_ dissolving connections in it, to be
garbage-collected when all active references are gone. It's
considerably saner wrt "is the subtree busy" logics, but it's nowhere
near being ready for merge at the moment; this changeset is one of the
things becoming possible with that sucker, but it certainly shouldn't
have been picked during this cycle. My apologies..."
Noticed-by: Eric Paris <eparis@redhat.com> Requested-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Mason [Thu, 17 Dec 2009 20:47:17 +0000 (15:47 -0500)]
Btrfs: make sure fallocate properly starts a transaction
The recent patch to make fallocate enospc friendly would send
down a NULL trans handle to the allocator. This moves the
transaction start to properly fix things.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Josef Bacik [Mon, 7 Dec 2009 21:45:59 +0000 (21:45 +0000)]
Btrfs: make metadata chunks smaller
This patch makes us a bit less zealous about making sure we have enough free
metadata space by pearing down the size of new metadata chunks to 256mb instead
of 1gb. Also, we used to try an allocate metadata chunks when allocating data,
but that sort of thing is done elsewhere now so we can just remove it. With my
-ENOSPC test I used to have 3gb reserved for metadata out of 75gb, now I have
1.7gb. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Matthew Wilcox [Mon, 14 Dec 2009 22:01:12 +0000 (22:01 +0000)]
Btrfs: Show discard option in /proc/mounts
Christoph's patch e244a0aeb6a599c19a7c802cda6e2d67c847b154 doesn't display
the discard option in /proc/mounts, leading to some confusion for me.
Here's the missing bit.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
TARUISI Hiroaki [Thu, 12 Nov 2009 07:14:26 +0000 (07:14 +0000)]
Btrfs: deny sys_link across subvolumes.
I rebased Christian Parpart's patch to deny hard link across
subvolumes. Original patch modifies also btrfs_rename, but
I excluded it because we can move across subvolumes now and
it make no problem.
-----------------
Hard link across subvolumes should not allowed in Btrfs.
btrfs_link checks root of 'to' directory is same as root
of 'from' file. If not same, btrfs_link returns -EPERM.
Signed-off-by: TARUISI Hiroaki <taruishi.hiroak@jp.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan, Zheng [Thu, 12 Nov 2009 09:36:50 +0000 (09:36 +0000)]
Btrfs: Fix per root used space accounting
The bytes_used field in root item was originally planned to
trace the amount of used data and tree blocks. But it never
worked right since we can't trace freeing of data accurately.
This patch changes it to only trace the amount of tree blocks.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan, Zheng [Thu, 12 Nov 2009 09:36:34 +0000 (09:36 +0000)]
Btrfs: Add delayed iput
iput() can trigger new transactions if we are dropping the
final reference, so calling it in btrfs_commit_transaction
may end up deadlock. This patch adds delayed iput to avoid
the issue.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan, Zheng [Thu, 12 Nov 2009 09:35:36 +0000 (09:35 +0000)]
Btrfs: Make truncate(2) more ENOSPC friendly
truncating and deleting regular files are unbound operations,
so it's not good to do them in a single transaction. This
patch makes btrfs_truncate and btrfs_delete_inode start a
new transaction after all items in a tree leaf are deleted.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan, Zheng [Thu, 12 Nov 2009 09:34:52 +0000 (09:34 +0000)]
Btrfs: Make fallocate(2) more ENOSPC friendly
fallocate(2) may allocate large number of file extents, so it's not
good to do it in a single transaction. This patch make fallocate(2)
start a new transaction for each file extents it allocates.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan, Zheng [Thu, 12 Nov 2009 09:34:40 +0000 (09:34 +0000)]
Btrfs: Avoid orphan inodes cleanup while replaying log
We do log replay in a single transaction, so it's not good to do unbound
operations. This patch cleans up orphan inodes cleanup after replaying
the log. It also avoids doing other unbound operations such as truncating
a file during replaying log. These unbound operations are postponed to
the orphan inode cleanup stage.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Yan, Zheng [Thu, 12 Nov 2009 09:34:21 +0000 (09:34 +0000)]
Btrfs: Fix disk_i_size update corner case
There are some cases file extents are inserted without involving
ordered struct. In these cases, we update disk_i_size directly,
without checking pending ordered extent and DELALLOC bit. This
patch extends btrfs_ordered_update_i_size() to handle these cases.
Signed-off-by: Yan Zheng <zheng.yan@oracle.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Thu, 17 Dec 2009 16:08:57 +0000 (08:08 -0800)]
Merge branch 'for-linus' of git://gitserver.sunplusct.com/linux-2.6-score
* 'for-linus' of git://gitserver.sunplusct.com/linux-2.6-score:
score: include asm-generic/param.h in asm/delay.h.
score: fixed pfn_valid define.
score: add flush_dcahce_page and PG_dcache_dirty define
Linus Torvalds [Thu, 17 Dec 2009 16:08:36 +0000 (08:08 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (27 commits)
regulator: wm831x_reg_read() failure unnoticed in wm831x_aldo_get_mode()
twl-regulator: Fix reg_disable functionality for 4030 and 6030
twl-regulator: Add turnon delay to reg_enable
twl-regulator: Restore REMAP configuration in regulator probe
twl-regulator: Add turnon-delay and REMAP config to twlreg_info struct
twl-regulator: Define critical regulators as always_on
twl-regulator: Add all twl4030 regulators to twlreg_info
regulator: mc13783-regulator: correct the probing time.
regulator: Fix unbalanced disables/enables in regulator_bulk_{enable,disable} error path
regulator: core.c: Small coding style cleanup (indentation fixup)
drivers/regulator: use PTR_ERR to get error code
regulator: consumer.h - fix build when consumer.h is #included first.
regulator/mc13783: various cleanups
regulator/mc13783: rename source file to match other drivers
Fix some AB3100 regulator issues
regulator: keep index within bounds in da9034_get_ldo12_voltage()
regulator: Ensure val is initialised in 88pm8607 choose_voltage()
regulator: Remove duplicate consts from ab3100
regulator: Handle regulators without suspend mode configuration
regulator: Factor out regulator name pretty printing
...
We recently go rid of all callers of do_sync_file_range as they're better
served with vfs_fsync or the filemap_write_and_wait. Now that
do_sync_file_range is down to a single caller fold it into it so that people
don't start using it again accidentally. While at it also switch it from
using __filemap_fdatawrite_range(..., WB_SYNC_ALL) to the more clear
filemap_fdatawrite_range().
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
hartleys [Mon, 14 Dec 2009 22:40:05 +0000 (22:40 +0000)]
spi: spi_sh_sci.c: use resource_size()
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
hartleys [Mon, 14 Dec 2009 22:37:15 +0000 (22:37 +0000)]
spi: spi_mpc8xxx.c: use resource_size()
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
projects / karo-tx-linux.git / log