brcmfmac has been broken on my cubietruck with a BCM43362:
brcmfmac: brcmf_chip_recognition: found AXI chip: BCM43362, rev=1
brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0:
Apr 22 2013 14:50:00 version 5.90.195.89.6 FWID 01-b30a427d
since commit 53036261033: "brcmfmac: update core reset and disable routines".
The problem is that since this commit brcmf_chip_ai_resetcore no longer sets
BCMA_IOCTL itself before bringing the core out of reset, instead relying on
brcmf_chip_ai_coredisable to do so. But brcmf_chip_ai_coredisable is a nop
of the chip is already in reset. This patch modifies brcmf_chip_ai_coredisable
to always set BCMA_IOCTL even if the core is already in reset.
This fixes brcmfmac hanging in firmware loading on my board.
Cc: stable@vger.kernel.org # v3.14 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[arend@broadcom.com: rebase patch on linux-3.14.y branch] Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Basically what's happening is, during netns cleanup,
nf_nat_net_exit gets called before ipv4_net_exit. As I understand
it, nf_nat_net_exit is supposed to kill any conntrack entries which
have NAT context (through nf_ct_iterate_cleanup), but for some
reason this doesn't happen (perhaps something else is still holding
refs to those entries?).
When ipv4_net_exit is called, conntrack entries (including those
with NAT context) are cleaned up, but the
nat_bysource hashtable is long gone - freed in nf_nat_net_exit. The
bug happens when attempting to free a conntrack entry whose NAT hash
'prev' field points to a slot in the freed hash table (head for that
bin).
We ignore conntracks with null nat bindings. But this is wrong,
as these are in bysource hash table as well.
Restore nat-cleaning for the netns-is-being-removed case.
If INPCK is not set, input parity detection should be disabled. This means
parity errors should not be received from the tty driver, and the data
received should be treated normally.
SUS v3, 11.2.2, General Terminal Interface - Input Modes, states:
"If INPCK is set, input parity checking shall be enabled. If INPCK is
not set, input parity checking shall be disabled, allowing output parity
generation without input parity errors. Note that whether input parity
checking is enabled or disabled is independent of whether parity detection
is enabled or disabled (see Control Modes). If parity detection is enabled
but input parity checking is disabled, the hardware to which the terminal
is connected shall recognize the parity bit, but the terminal special file
shall not check whether or not this bit is correctly set."
Ignore parity errors reported by the tty driver when INPCK is not set, and
handle the received data normally.
Fixes: Bugzilla #71681, 'Improvement of n_tty_receive_parity_error from n_tty.c' Reported-by: Ivan <athlon_@mail.ru> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
We forgot to add the status bit for the PLLs and we were using
the wrong register and masks for configuration, leading to
unexpected PLL configurations. Fix this.
Fixes: d8b212014e69 (clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC)) Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Mike Turquette <mturquette@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit eb17711bc1d6 ("net/mlx4_core: Introduce nic_info new flag in
QUERY_FUNC_CAP") did:
if (func_cap->flags1 & QUERY_FUNC_CAP_FLAGS1_OFFSET) {
which should be:
if (func_cap->flags1 & QUERY_FUNC_CAP_FLAGS1_FORCE_VLAN) {
Fix that.
Fixes: eb17711bc1d6 ("net/mlx4_core: Introduce nic_info new flag in QUERY_FUNC_CAP") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With a kernel configured with ARM64_64K_PAGES && !TRANSPARENT_HUGEPAGE,
the following is triggered at early boot:
SMP: Total of 8 processors activated.
devtmpfs: initialized
Unable to handle kernel NULL pointer dereference at virtual address 00000008
pgd = fffffe0000050000
[00000008] *pgd=00000043fba00003, *pmd=00000043fba00003, *pte=00e0000078010407
Internal error: Oops: 96000006 [#1] SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.15.0-rc864k+ #44
task: fffffe03bc040000 ti: fffffe03bc080000 task.ti: fffffe03bc080000
PC is at __list_add+0x10/0xd4
LR is at free_one_page+0x270/0x638
...
Call trace:
__list_add+0x10/0xd4
free_one_page+0x26c/0x638
__free_pages_ok.part.52+0x84/0xbc
__free_pages+0x74/0xbc
init_cma_reserved_pageblock+0xe8/0x104
cma_init_reserved_areas+0x190/0x1e4
do_one_initcall+0xc4/0x154
kernel_init_freeable+0x204/0x2a8
kernel_init+0xc/0xd4
This happens because init_cma_reserved_pageblock() calls
__free_one_page() with pageblock_order as page order but it is bigger
than MAX_ORDER. This in turn causes accesses past zone->free_list[].
Fix the problem by changing init_cma_reserved_pageblock() such that it
splits pageblock into individual MAX_ORDER pages if pageblock is bigger
than a MAX_ORDER page.
In cases where !CONFIG_HUGETLB_PAGE_SIZE_VARIABLE, which is all
architectures expect for ia64, powerpc and tile at the moment, the
â\80\9cpageblock_order > MAX_ORDERâ\80\9d condition will be optimised out since both
sides of the operator are constants. In cases where pageblock size is
variable, the performance degradation should not be significant anyway
since init_cma_reserved_pageblock() is called only at boot time at most
MAX_CMA_AREAS times which by default is eight.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Reported-by: Mark Salter <msalter@redhat.com> Tested-by: Mark Salter <msalter@redhat.com> Tested-by: Christopher Covington <cov@codeaurora.org> Cc: Mel Gorman <mgorman@suse.de> Cc: David Rientjes <rientjes@google.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ras3 block on spear320 claims to have 3 interrupts. In fact it has
one and 6 reserved interrupts. Account the 6 reserved to this block so
it has 7 interrupts total. That matches the datasheet and the device
tree entries.
Broken since commit 80515a5a(ARM: SPEAr3xx: shirq: simplify and move
the shared irq multiplexor to DT). Testing is overrated....
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20140619212712.872379208@linutronix.de Fixes: 80515a5a2e3c ('ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT') Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we write to a degraded array which has a bitmap, we
make sure the relevant bit in the bitmap remains set when
the write completes (so a 're-add' can quickly rebuilt a
temporarily-missing device).
If, immediately after such a write starts, we incorporate a spare,
commence recovery, and skip over the region where the write is
happening (because the 'needs recovery' flag isn't set yet),
then that write will not get to the new device.
Once the recovery finishes the new device will be trusted, but will
have incorrect data, leading to possible corruption.
We cannot set the 'needs recovery' flag when we start the write as we
do not know easily if the write will be "degraded" or not. That
depends on details of the particular raid level and particular write
request.
This patch fixes a corruption issue of long standing and so it
suitable for any -stable kernel. It applied correctly to 3.0 at
least and will minor editing to earlier kernels.
Reported-by: Bill <billstuff2001@sbcglobal.net> Tested-by: Bill <billstuff2001@sbcglobal.net> Link: http://lkml.kernel.org/r/53A518BB.60709@sbcglobal.net Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disabling reading and writing to the trace file should not be able to
disable all function tracing callbacks. There's other users today
(like kprobes and perf). Reading a trace file should not stop those
from happening.
It appears that no one ever run ffs-test on a big-endian machine,
since it used cpu-endianess for fs_count and hs_count fields which
should be in little-endian format. Fix by wrapping the numbers in
cpu_to_le32.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An NFS operation that creates a new symlink includes the symlink data,
which is xdr-encoded as a length followed by the data plus 0 to 3 bytes
of zero-padding as required to reach a 4-byte boundary.
The vfs, on the other hand, wants null-terminated data.
The simple way to handle this would be by copying the data into a newly
allocated buffer with space for the final null.
The current nfsd_symlink code tries to be more clever by skipping that
step in the (likely) case where the byte following the string is already
0.
But that assumes that the byte following the string is ours to look at.
In fact, it might be the first byte of a page that we can't read, or of
some object that another task might modify.
Worse, the NFSv4 code tries to fix the problem by actually writing to
that byte.
In the NFSv2/v3 cases this actually appears to be safe:
- nfs3svc_decode_symlinkargs explicitly null-terminates the data
(after first checking its length and copying it to a new
page).
- NFSv2 limits symlinks to 1k. The buffer holding the rpc
request is always at least a page, and the link data (and
previous fields) have maximum lengths that prevent the request
from reaching the end of a page.
In the NFSv4 case the CREATE op is potentially just one part of a long
compound so can end up on the end of a page if you're unlucky.
The minimal fix here is to copy and null-terminate in the NFSv4 case.
The nfsd_symlink() interface here seems too fragile, though. It should
really either do the copy itself every time or just require a
null-terminated string.
Reported-by: Jeff Layton <jlayton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should be returning a negative error code instead of success here.
This would have been detected by GCC, except that the "ret" variable was
initialized with a bogus value to disable GCC's uninitialized variable
warnings. I've cleaned that up, as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in the inkern.c code for IIO framework, the function
of_iio_channel_get_by_name() will return a non-NULL pointer when
it cannot find a channel using of_iio_channel_get() and when it
tries to search for 'io-channel-ranges' property and fails. This
is incorrect behaviour as the function which calls this expects
a NULL pointer for failure. This patch rectifies the issue.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When kvm_write_guest writes the tsc_ref structure to the guest, or it will lead
the low HV_X64_MSR_TSC_REFERENCE_ADDRESS_SHIFT bits of the TSC page address
must be cleared, or the guest can see a non-zero sequence number.
Otherwise Windows guests would not be able to get a correct clocksource
(QueryPerformanceCounter will always return 0) which causes serious chaos.
Recent Intel CPUs have 10 variable range MTRRs. Since operating systems
sometime make assumptions on CPUs while they ignore capability MSRs, it is
better for KVM to be consistent with recent CPUs. Reporting more MTRRs than
actually supported has no functional implications.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hole punching code for files with indirect blocks wrongly computed
number of blocks which need to be cleared when traversing the indirect
block tree. That could result in punching more blocks than actually
requested and thus effectively cause a data loss. For example:
Error recovery in ext4_alloc_branch() calls ext4_forget() even for
buffer corresponding to indirect block it did not allocate. This leads
to brelse() being called twice for that buffer (once from ext4_forget()
and once from cleanup in ext4_ind_map_blocks()) leading to buffer use
count misaccounting. Eventually (but often much later because there
are other users of the buffer) we will see messages like:
VFS: brelse: Trying to free free buffer
Another manifestation of this problem is an error:
JBD2 unexpected failure: jbd2_journal_revoke: !buffer_revoked(bh);
inconsistent data on disk
The fix is easy - don't forget buffer we did not allocate. Also add an
explanatory comment because the indexing at ext4_alloc_branch() is
somewhat subtle.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fix converts blkg->refcnt from int to atomic_t. It does some
overhead but it should be minute compared to everything else which is
going on and the involved cacheline bouncing, so I think it's highly
unlikely to cause any noticeable difference. Also, the refcnt in
question should be converted to a perpcu_ref for blk-mq anyway, so the
atomic_t is likely to go away pretty soon anyway.
Thanks.
------- 8< -------
__blkg_release_rcu() may be invoked after the associated request_queue
is released with a RCU grace period inbetween. As such, the function
and callbacks invoked from it must not dereference the associated
request_queue. This is clearly indicated in the comment above the
function.
Unfortunately, while trying to fix a different issue, 2a4fd070ee85
("blkcg: move bulk of blkcg_gq release operations to the RCU
callback") ignored this and added [un]locking of @blkg->q->queue_lock
to __blkg_release_rcu(). This of course can cause oops as the
request_queue may be long gone by the time this code gets executed.
The request_queue locking was added because blkcg_gq->refcnt is an int
protected with the queue lock and __blkg_release_rcu() needs to put
the parent. Let's fix it by making blkcg_gq->refcnt an atomic_t and
dropping queue locking in the function.
Given the general heavy weight of the current request_queue and blkcg
operations, this is unlikely to cause any noticeable overhead.
Moreover, blkcg_gq->refcnt is likely to be converted to percpu_ref in
the near future, so whatever (most likely negligible) overhead it may
add is temporary.
When we SMB3 mounted with mapchars (to allow reserved characters : \ / > < * ?
via the Unicode Windows to POSIX remap range) empty paths
(eg when we open "" to query the root of the SMB3 directory on mount) were not
null terminated so we sent garbarge as a path name on empty paths which caused
SMB2/SMB2.1/SMB3 mounts to fail when mapchars was specified. mapchars is
particularly important since Unix Extensions for SMB3 are not supported (yet)
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: David Disseldorp <ddiss@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Björn Baumbach <bb@sernet.de> Signed-off-by: Stefan Metzmacher <metze@samba.org> Reviewed-by: Stefan Metzmacher <metze@samba.org> Cc: Pavel Shilovsky <piastry@etersoft.ru> Cc: Steve French <sfrench@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for firmware rev 508+ was added years ago, but we never noticed
it reports channel in a different way for G-PHY devices. Instead of
offset from 2400 MHz it simply passes channel id (AKA hw_value).
So far it was (most probably) affecting monitor mode users only, but
the following recent commit made it noticeable for quite everybody:
If the mdio probe function fails in emac_open, the interrupt we just requested
isn't freed. If emac_open is called again, for example because we try to set up
the interface again, the kernel will oops because the interrupt wasn't properly
released.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value of ESR has been stored into x1, and should be directly pass to
do_sp_pc_abort function, "MOV x1, x25" is an extra operation and do_sp_pc_abort
will get the wrong value of ESR.
Fix a parser-bug in the omap2 muxing code where muxtable-entries will be
wrongly selected if the requested muxname is a *prefix* of their
m0-entry and they have a matching mN-entry. Fix by additionally checking
that the length of the m0_entry is equal.
For example muxing of "dss_data2.dss_data2" on omap32xx will fail
because the prefix "dss_data2" will match the mux-entries "dss_data2" as
well as "dss_data20", with the suffix "dss_data2" matching m0 (for
dss_data2) and m4 (for dss_data20). Thus both are recognized as signal
path candidates:
This will result in a failure to mux the pin at all:
_omap_mux_get_by_name: Multiple signal paths (2) for dss_data2.dss_data2
Patch should apply to linus' latest master down to rather old linux-2.6
trees.
Signed-off-by: David R. Piegdon <lkml@p23q.org> Cc: stable@vger.kernel.org
[tony@atomide.com: updated description to include full description] Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The __sync_icache_dcache routine will only flush the dcache for the
first page of a compound page, potentially leading to stale icache
data residing further on in a hugetlb page.
This patch addresses this issue by taking into consideration the
order of the page when flushing the dcache.
Reported-by: Mark Brown <broonie@linaro.org> Tested-by: Mark Brown <broonie@linaro.org> Signed-off-by: Steve Capper <steve.capper@linaro.org> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
However, if the percpu_pagelist_fraction sysctl is set by the user, it
is also impossible to restore it to the kernel default since the user
cannot write 0 to the sysctl.
This patch allows the user to write 0 to restore the default behavior.
It still requires a fraction equal to or larger than 8, however, as
stated by the documentation for sanity. If a value in the range [1, 7]
is written, the sysctl will return EINVAL.
This successfully solves the divide by zero issue at the same time.
Signed-off-by: David Rientjes <rientjes@google.com> Reported-by: Oleg Drokin <green@linuxhacker.ru> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a race between fork() and hugepage migration, as a result we try
to "dereference" a swap entry as a normal pte, causing kernel panic.
The cause of the problem is that copy_hugetlb_page_range() can't handle
"swap entry" family (migration entry and hwpoisoned entry) so let's fix
it.
Without this fix, freshly rebooted Linux creates a new IBSS
instead of joining an existing one. Only when jiffies counter
overflows after 5 minutes the IBSS can be successfully joined.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
[edit commit message slightly] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a mistake in the actual rounding portion this previous patch: f0fe3cd7e12d (intel_pstate: Correct rounding in busy calculation) such that
the rounding was asymetric and incorrect.
Severity: Not very serious, but can increase target pstate by one extra value.
For real world work flows the issue should self correct (but I have no proof).
It is the equivalent of different PID gains for positive and negative numbers.
Examples:
-3.000000 used to round to -4, rounds to -3 with this patch.
-3.503906 used to round to -5, rounds to -4 with this patch.
Fixes: f0fe3cd7e12d (intel_pstate: Correct rounding in busy calculation) Signed-off-by: Doug Smythies <dsmythies@telus.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All devices supported by ina2xx are bidirectional and report the
measured shunt voltage and power values as a signed 16 bit, but the
current driver implementation caches all registers as u16, leading
to an incorrect sign extension when reporting to userspace in
ina2xx_get_value().
This patch fixes the problem by casting the signed registers to s16.
Tested on an INA219.
allows the fall through to the non-layered write case even if both
parent_overlap and obj_request->img_offset belong to the same RADOS
object. This leads to data corruption, because the area to the left of
parent_overlap ends up unconditionally zero-filled instead of being
populated with parent data. Suppose we want to write 1M to offset 6M
of image bar, which is a clone of foo@snap; object_size is 4M,
parent_overlap is 5M:
rbd_data.<id>.0000000000000001
---------------------|----------------------|------------
| should be copyup'ed | should be zeroed out | write ...
---------------------|----------------------|------------
4M 5M 6M
parent_overlap obj_request->img_offset
4..5M should be copyup'ed from foo, yet it is zero-filled, just like
5..6M is.
Given that the only striping mode kernel client currently supports is
chunking (i.e. stripe_unit == object_size, stripe_count == 1), round
parent_overlap up to the next object boundary for the purposes of the
overlap check.
Each image request contains a reference count, but to date it has
not actually been used. (I think this was just an oversight.) A
recent report involving rbd failing an assertion shed light on why
and where we need to use these reference counts.
Every OSD request associated with an object request uses
rbd_osd_req_callback() as its callback function. That function will
call a helper function (dependent on the type of OSD request) that
will set the object request's "done" flag if the object request if
appropriate. If that "done" flag is set, the object request is
passed to rbd_obj_request_complete().
In rbd_obj_request_complete(), requests are processed in sequential
order. So if an object request completes before one of its
predecessors in the image request, the completion is deferred.
Otherwise, if it's a completing object's "turn" to be completed, it
is passed to rbd_img_obj_end_request(), which records the result of
the operation, accumulates transferred bytes, and so on. Next, the
successor to this request is checked and if it is marked "done",
(deferred) completion processing is performed on that request, and
so on. If the last object request in an image request is completed,
rbd_img_request_complete() is called, which (typically) destroys
the image request.
There is a race here, however. The instant an object request is
marked "done" it can be provided (by a thread handling completion of
one of its predecessor operations) to rbd_img_obj_end_request(),
which (for the last request) can then lead to the image request
getting torn down. And this can happen *before* that object has
itself entered rbd_img_obj_end_request(). As a result, once it
*does* enter that function, the image request (and even the object
request itself) may have been freed and become invalid.
All that's necessary to avoid this is to properly count references
to the image requests. We tear down an image request's object
requests all at once--only when the entire image request has
completed. So there's no need for an image request to count
references for its object requests. However, we don't want an
image request to go away until the last of its object requests
has passed through rbd_img_obj_callback(). In other words,
we don't want rbd_img_request_complete() to necessarily
result in the image request being destroyed, because it may
get called before we've finished processing on all of its
object requests.
So the fix is to add a reference to an image request for
each of its object requests. The reference can be viewed
as representing an object request that has not yet finished
its call to rbd_img_obj_callback(). That is emphasized by
getting the reference right after assigning that as the image
object's callback function. The corresponding release of that
reference is done at the end of rbd_img_obj_callback(), which
every image object request passes through exactly once.
DM thinp already checks whether the discard_granularity of the data
device is a factor of the thin-pool block size. But when using the
dm-thin-pool's discard passdown support, DM thinp was not selecting the
max of the underlying data device's discard_granularity and the
thin-pool's block size.
Update set_discard_limits() to set discard_granularity to the max of
these values. This enables blkdev_issue_discard() to properly align the
discards that are sent to the DM thin device on a full block boundary.
As such each discard will now cover an entire DM thin-pool block and the
block will be reclaimed.
The SMP code expects hdev to be unlocked since e.g. crypto functions
will try to (re)lock it. Therefore, we need to release the lock before
calling into smp.c from mgmt.c. Without this we risk a deadlock whenever
the smp_user_confirm_reply() function is called.
When inquiry is canceled through the HCI_Cancel_Inquiry command there is
no Inquiry Complete event generated. Instead, all we get is the command
complete for the HCI_Inquiry_Cancel command. This means that we must
call the hci_discovery_set_state() function from the respective command
complete handler in order to ensure that user space knows the correct
discovery state.
The conn->link_key variable tracks the type of link key in use. It is
set whenever we respond to a link key request as well as when we get a
link key notification event.
These two events do not however always guarantee that encryption is
enabled: getting a link key request and responding to it may only mean
that the remote side has requested authentication but not encryption. On
the other hand, the encrypt change event is a certain guarantee that
encryption is enabled. The real encryption state is already tracked in
the conn->link_mode variable through the HCI_LM_ENCRYPT bit.
This patch fixes a check for encryption in the hci_conn_auth function to
use the proper conn->link_mode value and thereby eliminates the chance
of a false positive result.
From the Bluetooth Core Specification 4.1 page 1958:
"if both devices have set the Authentication_Requirements parameter to
one of the MITM Protection Not Required options, authentication stage 1
shall function as if both devices set their IO capabilities to
DisplayOnly (e.g., Numeric comparison with automatic confirmation on
both devices)"
So far our implementation has done user confirmation for all just-works
cases regardless of the MITM requirements, however following the
specification to the word means that we should not be doing confirmation
when neither side has the MITM flag set.
Commit "drm/vmwgfx: correct fb_fix_screeninfo.line_length", while fixing a
vmwgfx fbdev bug, also writes the pitch to a supposedly read-only register:
SVGA_REG_BYTES_PER_LINE, while it should be (and also in fact is) written to
SVGA_REG_PITCHLOCK.
This patch is Cc'd stable because of the unknown effects writing to this
register might have, particularly on older device versions.
v2: Updated log message.
Cc: Christopher Friedt <chrisfriedt@gmail.com> Tested-by: Christopher Friedt <chrisfriedt@gmail.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Jakob Bornecrantz <jakob@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For reasons I can't claim to fully understand gen4 seems to require
backlight duty cycle setting after the backlight has been enabled, or
else black screen follows. I don't have documentation for the correct
sequence on gen4 either. Confirmed on Dell Latitude D630 and MacBook4,1.
This fixes a regression introduced by
commit b35684b8fa94e04f55fd38bf672b737741d2f9e2
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:13:41 2013 +0200
drm/i915: do full backlight setup at enable time
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75791 Reported-and-tested-by: mcy@lm7.fr
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79423 Reported-and-tested-by: Marc Milgram <mmilgram@redhat.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On certain platforms pixel_multiplier is read out in
.get_pipe_config(), but it also gets used to calculate the
pixel clock in intel_sdvo_get_config(). If the pipe is disable
but some SDVO outputs are active, we may end up dividing by zero
in intel_sdvo_get_config().
To avoid the problem simply check for zero pixel_multiplier and skip
the division. Another attempt at fixing this involved populating
pixel_multiplier to 1 even for disabled pipes, but that triggered a
WARN because SDVO_CMD_GET_CLOCK_RATE_MULT command failed and thus
encoder_pixel_multiplier was left at zero and didn't match
pipe_config->pixel_multiplier.
The "divide by pixel_multiplier" operation got introduced here:
commit 18442d08786472c63a0a80c27f92b033dffc26de
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 13 16:00:08 2013 +0300
drm/i915: Fix port_clock and adjusted_mode.clock readout all over
and it has caused a regression on certain machines since they would
hit the div-by-zero during resume.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76520 Tested-by: Tim Richardson <tim@tim-richardson.net> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever a single nouveau_mc_intr() main gpu irq-handler invocation was
responsible for calling both, the vblank-irq handler (display engine irq)
and kms-pageflip completion handler (from fifo irq), the order of
invocation was wrong. nouveau_finish_flip() was called before
drm_handle_vblank() for the vblank of pageflip completion, so the
emitted pageflip event contained stale vblank count and timestamp
from previous vblank. This caused failure in userspace to timestamp
properly.
Reorder order of invocation of engine irq handlers: Put
NVDEV_ENGINE_DISP always on top, and thereby before NVDEV_ENGINE_FIFO,
so that drm_handle_vblank() gets called to update vblank timestamps
and count before potential pageflip events make use of that
information.
This works on nv-50 and later, where kms-pageflip completion triggers
an irq either after a separate vblank irq, or both pageflip and vblank
trigger one common irq invocation, but never before vblank irqs.
v2 (Ben):
- removed mods for nv04-nv40, it doesn't help there anyway
- this is considered a hack, and a better solution should be found
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Possibly also fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=68571
Noticed-by: Jonathan Howard <jonathan@unbiased.name> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Marek Olšák <marek.olsak@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Need to drm_vblank_get/put() the crtc involved in a
pending pageflip, or we might not get vblank irqs and
updates of vblank counts and timestamps for pageflip
events and flip completion.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nv04_disp_scanoutpos() must abort to trigger simple timestamping
fallback if vtotal/htotal regs return zero. This happens if the
output isn't a digital output, but a vga analog output, as the
regs don't get initialized in that case.
Fixes timestamping failure on nv-40 and earlier with vga output.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cards with nv04 display engine can't reliably use vblank
counts and timestamps computed via drm_handle_vblank(), as
the function gets invoked after sending the pageflip events.
Fix this by defaulting to the old crtcid = -1 fallback path
on <= NV-50 cards, and only using the precise path on NV-50
and later.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pxa3xx_nand driver currently uses __raw_writel() and __raw_readl()
to access I/O registers. However, those functions do not do any
endianness swapping, which means that they won't work when the CPU
runs in big-endian but the I/O registers are little endian, which is
the common situation for ARM systems running big endian.
Since __raw_writel() and __raw_readl() do not include any memory
barriers and the pxa3xx_nand driver can only be compiled for ARM
platforms, the closest I/o accessors functions that do endianess
swapping are writel_relaxed() and readl_relaxed().
This patch has been verified to work on Armada XP GP: without the
patch, the NAND is not detected when the kernel runs big endian while
it is properly detected when the kernel runs little endian. With the
patch applied, the NAND is properly detected in both situations
(little and big endian).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In omap_elm_correct_data(), if bitflip_count in an erased-page is within the
correctable limit (< ecc.strength), then it is not indicated back to the caller
ecc->read_page().
This mis-guides upper layers like MTD and UBIFS layer to assume erased-page as
perfectly clean and use it for writing even if actual bitflip_count was
dangerously high (bitflip_count > mtd->bitflip_threshold).
This patch fixes this above issue, by returning 'stats' to caller
ecc->read_page() under all scenarios.
Reported-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Pekon Gupta <pekon@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As subpage write is enabled by default for all drivers, nand_write_subpage_hwecc
causes a crash if the driver did not register ecc->hwctl or ecc->calculate.
This behavior was introduced in
commit 837a6ba4f3b6d23026674e6af6b6849a4634fff9
"mtd: nand: subpage write support for hardware based ECC schemes".
This fixes a crash by emulating subpage write support by padding sub-page data
with 0xff on either sides to make it full page compatible.
Reported-by: Helmut Schaa <helmut.schaa@googlemail.com> Tested-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Pekon Gupta <pekon@ti.com> Reviewed-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Niels, starting rfkill polling during device probe
(commit e2bc7c5, generally sane change) broke rfkill on rt2500pci
device. I considered that bug as some initalization issue, which
should be fixed on rt2500pci specific code. But after several
attempts (see bug report for details) we fail to find working solution.
Hence I decided to revert to old behaviour on rt2500pci to fix
regression.
Additionally patch also unregister rfkill on device remove instead
of ifconfig down, what was another issue introduced by bad commit.
If the descriptors do not need any strings and user space sends empty
set of strings, the ffs->stringtabs field remains NULL. Thus
*ffs->stringtabs in functionfs_bind leads to a NULL pointer
dereferenece.
The bug was introduced by commit [fd7c9a007f: “use usb_string_ids_n()”].
While at it, remove double initialisation of lang local variable in
that function.
ffs->strings_count does not need to be checked in any way since in
the above scenario it will remain zero and usb_string_ids_n() is
a no-operation when colled with 0 argument.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though usb_functionfs_descs_head structure is now deprecated,
it has been used by some user space tools. Its removel in commit
[ac8dde1: “Add flags to descriptors block”] was an oversight
leading to build breakage for such tools.
Bring it back so that old user space tools can still be build
without problems on newer kernel versions.
Reported-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Reported-by: Krzysztof Opasiak <k.opasiak@samsung.com> Signed-off-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to delete un-finished td from current request's td list
at ep_dequeue API, otherwise, this non-user td will be remained
at td list before this request is freed. So if we do ep_queue->
ep_dequeue->ep_queue sequence, when the complete interrupt for
the second ep_queue comes, we search td list for this request,
the first td (added by the first ep_queue) will be handled, and
its status is still active, so we will consider the this transfer
still not be completed, but in fact, it has completed. It causes
the peripheral side considers it never receives current data for
this transfer.
We met this problem when do "Error Recovery Test - Device Configured"
test item for USBCV2 MSC test, the host has never received ACK for
the IN token for CSW due to peripheral considers it does not get this
CBW, the USBCV test log like belows:
--------------------------------------------------------------------------
INFO
Issuing BOT MSC Reset, reset should always succeed
INFO
Retrieving status on CBW endpoint
INFO
CBW endpoint status = 0x0
INFO
Retrieving status on CSW endpoint
INFO
CSW endpoint status = 0x0
INFO
Issuing required command (Test Unit Ready) to verify device has recovered
INFO
Issuing CBW (attempt #1):
INFO
|----- CBW LUN = 0x0
INFO
|----- CBW Flags = 0x0
INFO
|----- CBW Data Transfer Length = 0x0
INFO
|----- CBW CDB Length = 0x6
INFO
|----- CBW CDB-00 = 0x0
INFO
|----- CBW CDB-01 = 0x0
INFO
|----- CBW CDB-02 = 0x0
INFO
|----- CBW CDB-03 = 0x0
INFO
|----- CBW CDB-04 = 0x0
INFO
|----- CBW CDB-05 = 0x0
INFO
Issuing CSW : try 1
INFO
CSW Bulk Request timed out!
ERROR
Failed CSW phase : should have been success or stall
FAIL
(5.3.4) The CSW status value must be 0x00, 0x01, or 0x02.
ERROR
BOTCommonMSCRequest failed: error=80004000
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At probe time, the musb_am335x driver register its childs by
calling of_platform_populate(), which registers all childs in
the devicetree hierarchy recursively.
On the other side, the driver's remove() function uses of_device_unregister()
to remove each child of musb_am335x's.
However, when musb_dsps is loaded, its devices are attached to the musb_am335x
device as musb_am335x childs. Hence, musb_am335x remove() will attempt to
unregister the devices registered by musb_dsps, which produces a kernel panic.
In other words, the childs in the "struct device" hierarchy are not the same
as the childs in the "devicetree" hierarchy.
Ideally, we should enforce the removal of the devices registered by
musb_am335x *only*, instead of all its child devices. However, because of the
recursive nature of of_platform_populate, this doesn't seem possible.
Therefore, as the only solution at hand, this commit disables musb_am335x
driver removal capability, preventing it from being ever removed. This was
originally suggested by Sebastian Siewior:
Some TI chips raise the DMA complete interrupt before the actual
transfer has been completed. The code tries to busy wait for a few
microseconds and if that fails it arms an hrtimer to recheck. So far
so good, but that has the following issue:
CPU 0 CPU1
start_next_transfer(RQ1);
DMA interrupt
if (premature_irq(RQ1))
if (!hrtimer_active(timer))
hrtimer_start(timer);
DMA interrupt
if (premature_irq(RQ2))
if (!hrtimer_active(timer))
hrtimer_start(timer);
timer->state = INACTIVE;
The premature interrupt of request2 on CPU1 does not arm the timer and
therefor the request completion never happens because it checks for
!hrtimer_active(). hrtimer_active() evaluates:
timer->state != HRTIMER_STATE_INACTIVE
which of course evaluates to true in the above case as timer->state is
CALLBACK_RUNNING.
That's clearly documented:
* A timer is active, when it is enqueued into the rbtree or the
* callback function is running or it's in the state of being migrated
* to another cpu.
But that's not what the code wants to check. The code wants to check
whether the timer is queued, i.e. whether its armed and waiting for
expiry.
We have a helper function for this: hrtimer_is_queued(). This
evaluates:
timer->state & HRTIMER_STATE_QUEUED
So in the above case this evaluates to false and therefor forces the
DMA interrupt on CPU1 to call hrtimer_start().
Use hrtimer_is_queued() instead of hrtimer_active() and evrything is
good.
Reported-by: Torben Hohn <torbenh@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a regression in the upcoming v3.16-rc1, that is caused
by a problem that has been around for a while but now finally
hangs the system. The bootcrawl looks like this:
pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already
requested by a03e0000.usb_per5; cannot claim for musb-hdrc.0.auto
pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.0.auto) status -22
pinctrl-nomadik soc:pinctrl: could not request pin 256
(GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
musb-hdrc musb-hdrc.0.auto: Error applying setting, reverse
things back
HS USB OTG: no transceiver configured
musb-hdrc musb-hdrc.0.auto: musb_init_controller failed
with status -517
platform musb-hdrc.0.auto: Driver musb-hdrc requests
probe deferral
(...)
The ux500 MUSB driver propagates the OF node to the dynamically
created musb-hdrc device, which is incorrect as it makes the OF
core believe there are two devices spun from the very same
DT node, which confuses other parts of the device core, notably
the pin control subsystem, which will try to apply all the pin
control settings also to the HDRC device as it gets
instantiated. (The OMAP2430 for example, does not set the
of_node member.)
Cc: Arnd Bergmann <arnd@arndb.de> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device vendor and product id is 1c9e:9800
It is working as serial interface with generic usbserial driver.
I thought it is more suitable to use usbserial option driver, which has
better capability distinguishing between modem serial interface and
micro sd storage interface.
[ johan: style changes ]
Signed-off-by: Oliver Neukum <oneukum@suse.de> Tested-by: Alif Mubarak Ahmad <alive4ever@live.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system suspend flow as following:
1, Freeze all user processes and kenrel threads.
2, Try to suspend all devices.
2.1, If pci device is in RPM suspended state, then pci driver will try
to resume it to RPM active state in the prepare stage.
2.2, xhci_resume function calls usb_hcd_resume_root_hub to queue two
workqueue items to resume usb2&usb3 roothub devices.
2.3, Call suspend callbacks of devices.
2.3.1, All suspend callbacks of all hcd's children, including
roothub devices are called.
2.3.2, Finally, hcd_pci_suspend callback is called.
Due to workqueue threads were already frozen in step 1, the workqueue
items can't be scheduled, and the roothub devices can't be resumed in
this flow. The HCD_FLAG_WAKEUP_PENDING flag which is set in
usb_hcd_resume_root_hub won't be cleared. Finally,
hcd_pci_suspend will return -EBUSY, and system suspend fails.
The reason why this issue doesn't show up very often is due to that
choose_wakeup will be called in step 2.3.1. In step 2.3.1, if
udev->do_remote_wakeup is not equal to device_may_wakeup(&udev->dev), then
udev will resume to RPM active for changing the wakeup settings. This
has been a lucky hit which hides this issue.
For some special xHCI controllers which have no USB2 port, then roothub
will not match hub driver due to probe failed. Then its
do_remote_wakeup will be set to zero, and we won't be as lucky.
xhci driver doesn't need to resume roothub devices everytime like in
the above case. It's only needed when there are pending event TRBs.
This patch should be back-ported to kernels as old as 3.2, that
contains the commit f69e3120df82391a0ee8118e0a156239a06b2afb
"USB: XHCI: resume root hubs when the controller resumes"
The transfer burst count (TBC) field in xhci 1.0 hosts should be set
to the number of bursts needed to transfer all packets in a isoc TD.
Supported values are 0-2 (1 to 3 bursts per service interval).
Formula for TBC calculation is given in xhci spec section 4.11.2.3:
TBC = roundup( Transfer Descriptor Packet Count / Max Burst Size +1 ) - 1
This patch should be applied to stable kernels since 3.0 that contain
the commit 5cd43e33b9519143f06f507dd7cbee6b7a621885
"xhci 1.0: Set transfer burst count field."
Command completion events normally include command completion status,
SLOT_ID, and a pointer to the original command. Reset device command
completion SLOT_ID may be zero according to xhci specs 4.6.11.
VIA controllers set the SLOT_ID to zero, triggering a WARN_ON in the
command completion handler.
Use the SLOT ID found from the original command instead.
This patch should be applied to stable kernels since 3.13 that contain
the commit 20e7acb13ff48fbc884d5918c3697c27de63922a
"xhci: use completion event's slot id rather than dig it out of command"
Even though the virtio-scsi spec guarantees that all requests related
to the TMF will have been completed by the time the TMF itself completes,
the request queue's callback might not have run yet. This causes requests
to be completed more than once, and as a result triggers a variety of
BUGs or oopses.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Venkatesh Srinivas <venkateshs@google.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After scsi_try_to_abort_cmd returns, the eh_abort_handler may have
already found that the command has completed in the device, causing
the host_byte to be nonzero (e.g. it could be DID_ABORT). When
this happens, ORing DID_TIME_OUT into the host byte will corrupt
the result field and initiate an unwanted command retry.
Signed-off-by: Ulrich Obergfell <uobergfe@redhat.com>
[Fix all instances according to review comments. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling the workqueue interface on uninitialized work items isn't a
good idea even if they're zeroed. It's not failing catastrophically only
through happy accidents.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a memory barrier prior to sending a new command to the VIOS
to ensure the VIOS does not receive stale data in the command buffer.
Also add a memory barrier when processing the CRQ for completed commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a CRQ reset is triggered for some reason while in the middle
of performing VSCSI adapter initialization, we don't want to
call the done function for the initialization MAD commands as
this will only result in two threads attempting initialization
at the same time, resulting in failures.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to call the proper init function in case it has been
overridden, as it might restore things that the generic routing
doesn't know anything about. E.g. AMD cards have special verbs
that need resetting.
When a USB-audio device is disconnected while PCM is still running, we
still see some race: the disconnect callback calls
snd_usb_endpoint_free() that calls release_urbs() and then kfree()
while a PCM stream would be closed at the same time and calls
stop_endpoints() that leads to wait_clear_urbs(). That is, the EP
object might be deallocated while a PCM stream is syncing with
wait_clear_urbs() with the same EP.
Basically calling multiple wait_clear_urbs() would work fine, also
calling wait_clear_urbs() and release_urbs() would work, too, as
wait_clear_urbs() just reads some fields in ep. The problem is the
succeeding kfree() in snd_pcm_endpoint_free().
This patch moves out the EP deallocation into the later point, the
destructor callback. At this stage, all PCMs must have been already
closed, so it's safe to free the objects.
syscall_regfunc() and syscall_unregfunc() should set/clear
TIF_SYSCALL_TRACEPOINT system-wide, but do_each_thread() can race
with copy_process() and miss the new child which was not added to
the process/thread lists yet.
Change copy_process() to update the child's TIF_SYSCALL_TRACEPOINT
under tasklist.
Link: http://lkml.kernel.org/p/20140413185854.GB20668@redhat.com Fixes: a871bd33a6c0 "tracing: Add syscall tracepoints" Acked-by: Frederic Weisbecker <fweisbec@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to prevent the saved cmdline cache from being filled when
tracing is not active, the comms are only recorded after a trace event
is recorded.
The problem is, a comm can fail to be recorded if the trace_cmdline_lock
is held. That lock is taken via a trylock to allow it to happen from
any context (including NMI). If the lock fails to be taken, the comm
is skipped. No big deal, as we will try again later.
But! Because of the code that was added to only record after an event,
we may not try again later as the recording is made as a oneshot per
event per CPU.
Only disable the recording of the comm if the comm is actually recorded.
Fixes: 7ffbd48d5cab "tracing: Cache comms only after an event occurred" Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the SubmittingPatches process to include howto about the new
'Fixes:' tag to be used when a patch fixes an issue in a previous commit
(found by git-bisect for example).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan points out that I forgot to make the needed fixes to the
lz4_uncompress_unknownoutputsize() function to mirror the changes done
in lz4_decompress() with regards to potential pointer overflows.
The only in-kernel user of this function is the zram code, which only
takes data from a valid compressed buffer that it made itself, so it's
not a big issue. But due to external kernel modules using this
function, it's better to be safe here.
Reported-by: Jan Beulich <JBeulich@suse.com> Cc: "Don A. Bailey" <donb@securitymouse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'sysret' fastpath does not correctly restore even all regular
registers, much less any segment registers or reflags values. That is
very much part of why it's faster than 'iret'.
Normally that isn't a problem, because the normal ptrace() interface
catches the process using the signal handler infrastructure, which
always returns with an iret.
However, some paths can get caught using ptrace_event() instead of the
signal path, and for those we need to make sure that we aren't going to
return to user space using 'sysret'. Otherwise the modifications that
may have been done to the register set by the tracer wouldn't
necessarily take effect.
Fix it by forcing IRET path by setting TIF_NOTIFY_RESUME from
arch_ptrace_stop_needed() which is invoked from ptrace_stop().
Prior to commit 0e4f6a791b1e (Fix reiserfs_file_release()), reiserfs
truncates serialized on i_mutex. They mostly still do, with the exception
of reiserfs_file_release. That blocks out other writers via the tailpack
mutex and the inode openers counter adjusted in reiserfs_file_open.
However, NFS will call reiserfs_setattr without having called ->open, so
we end up with a race when nfs is calling ->setattr while another
process is releasing the file. Ultimately, it triggers the
BUG_ON(inode->i_size != new_file_size) check in maybe_indirect_to_direct.
The solution is to pull the lock into reiserfs_setattr to encompass the
truncate_setsize call as well.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit daba542 ("xfs: skip verification on initial "guess"
superblock read") dropped the use of a verifier for the initial
superblock read so we can probe the sector size of the filesystem
stored in the superblock. It, however, now fails to validate that
what was read initially is actually an XFS superblock and hence will
fail the sector size check and return ENOSYS.
This causes probe-based mounts to fail because it expects XFS to
return EINVAL when it doesn't recognise the superblock format.
Reported-by: Plamen Petrov <plamen.sisi@gmail.com> Tested-by: Plamen Petrov <plamen.sisi@gmail.com> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 59a53afe70fd530040bdc69581f03d880157f15a "powerpc: Don't setup
CPUs with bad status" broke ePAPR SMP booting. ePAPR says that CPUs
that aren't presently running shall have status of disabled, with
enable-method being used to determine whether the CPU can be enabled.
Fix by checking for spin-table, which is currently the only supported
enable-method.
Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Michael Neuling <mikey@neuling.org> Cc: Emil Medve <Emilian.Medve@Freescale.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Vector Crypto category instructions are supported by current POWER8
chips, advertise them to userspace using a specific bit to properly
differentiate with chips of the same architecture level that might not
have them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OPAL will mark a CPU that is guarded as "bad" in the status property of the CPU
node.
Unfortunatley Linux doesn't check this property and will put the bad CPU in the
present map. This has caused hangs on booting when we try to unsplit the core.
This patch checks the CPU is avaliable via this status property before putting
it in the present map.
Signed-off-by: Michael Neuling <mikey@neuling.org> Tested-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>