Huang Shijie [Thu, 16 Feb 2012 06:17:33 +0000 (14:17 +0800)]
mxs-dma : rewrite the last parameter of mxs_dma_prep_slave_sg()
[1] Background :
The GPMI does ECC read page operation with a DMA chain consist of three DMA
Command Structures. The middle one of the chain is used to enable the BCH,
and read out the NAND page.
The WAIT4END(wait for command end) is a comunication signal between
the GPMI and MXS-DMA.
[2] The current DMA code sets the WAIT4END bit at the last one, such as:
[3] But in the new GPMI version (used in MX50/MX60), the WAIT4END bit should
be set not only at the last DMA Command Structure,
but also at the middle one, such as:
+-----+ +-----+ +-----+
| cmd | ------------> | cmd | ------------------> | cmd |
+-----+ +-----+ +-----+
^ ^
| |
| |
set WAIT4END here too set WAIT4END here
If we do not set WAIT4END, the BCH maybe stalls in "ECC reading page" state.
In the next ECC write page operation, a DMA-timeout occurs.
This has been catched in the MX6Q board.
[4] In order to fix the bug, rewrite the last parameter of mxs_dma_prep_slave_sg(),
and use the dma_ctrl_flags:
---------------------------------------------------------
DMA_PREP_INTERRUPT : append a new DMA Command Structrue.
DMA_CTRL_ACK : set the WAIT4END bit for this DMA Command Structure.
---------------------------------------------------------
[5] changes to the relative drivers:
<1> For mxs-mmc driver, just use the new flags, do not change any logic.
<2> For gpmi-nand driver, and use the new flags to set the DMA
chain, especially for ecc read page.
Huang Shijie [Thu, 16 Feb 2012 06:17:32 +0000 (14:17 +0800)]
mxs-dma : move the mxs dma.h to a more common place
Move the header to a more common place.
The mxs dma engine is not only used in mx23/mx28, but also used
in mx50/mx6q. It will also be used in the future chips.
Rename it to mxs-dma.h, and create a new folder include/linux/fsl/ to
store the Freescale's header files.
change mxs-dma driver, mxs-mmc driver, gpmi-nand driver, mxs-saif driver
to the new header file.
Acked-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Huang Shijie <b32955@freescale.com> Acked-by: Vinod Koul <vinod.koul@linux.intel.com> Acked-by: Chris Ball <cjb@laptop.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Russell King [Wed, 15 Feb 2012 11:48:34 +0000 (11:48 +0000)]
mtd: fix 'Flash device refused suspend due to active operation' message
While debugging on SA11x0, the following message was observed:
"Flash device refused suspend due to active operation (state 20)"
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In commit "c797533 mtd: abstract last MTD partition parser argument" the
third argument of "mtd_device_parse_register()" changed from start address
of the MTD device to a pointer to a struct.
The "ixp4xx_flash_probe()" function was not converted properly, causing
an oops during boot.
This patch fixes the problem by filling the needed information into a
"struct mtd_part_parser_data" and passing it to
"mtd_device_parse_register()".
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Cc: stable@kernel.org [3.2+] Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch changes all the OTP functions like 'mtd_get_fact_prot_info()' and
makes them return zero immediately if the input 'len' parameter is 0. This is
not really needed currently, but most of the other functions do this, and it is
just consistent to do the same in the OTP functions.
This patch also moves the OTP functions from the header file to mtdcore.c
because they become a bit too big for being inlined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd: move zero length verification to MTD API functions
In many places in drivers we verify for the zero length, but this is very
inconsistent across drivers. This is obviously the right thing to do, though.
This patch moves the check to the MTD API functions instead and removes a lot
of duplication.
Some MTD drivers return -EINVAL if the 'phys' parameter is not NULL, trying to
convey that they cannot return the physical address. However, this is not very
logical because they still can return the virtual address ('virt'). But some
drivers (lpddr) just ignore the 'phys' parameter instead, which is a more
logical thing to do.
Let's harmonize this and:
1. Always initialize 'virt' and 'phys' to 'NULL' in 'mtd_point()'.
2. Do not return an error if the physical address cannot be found.
So as a result, all drivers will set 'phys' to 'NULL' if it is not supported.
None of the 'mtd_point()' users use 'phys' anyway, so this should not break
anything. I guess we could also just delete this parameter later.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The MTD API function now zero the 'retlen' parameter before calling
the driver's method — do not do this again in drivers. This removes
duplicated '*retlen = 0' assignent from the following methods:
Many drivers check whether the partition is R/O and return -EROFS if yes.
Let's stop having duplicated checks and move them to the API functions
instead.
And again a bit of noise - deleted few too sparse newlines, sorry.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd: do not duplicate length and offset checks in drivers
We already verify that offset and length are within the MTD device size
in the MTD API functions. Let's remove the duplicated checks in drivers.
This patch only affects the following API's:
The 'mtd_unpoint()' API function should be able to return an error code because
it may fail if you specify incorrect offset. This patch changes this MTD API
function and amends all the drivers correspondingly.
Also return '-EOPNOTSUPP' from 'mtd_unpoint()' when the '->unpoint()' method is
undefined. We do not really need this currently, but this just makes
sense to be consistent with 'mtd_point()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Mon, 6 Feb 2012 21:44:00 +0000 (13:44 -0800)]
mtd: nand: write BBM to OOB even with flash-based BBT
Currently, the flash-based BBT implementation writes bad block data only
to its flash-based table and not to the OOB marker area. Then, as new bad
blocks are marked over time, the OOB markers become incomplete and the
flash-based table becomes the only source of current bad block
information. This becomes an obvious problem when, for example:
* bootloader cannot read the flash-based BBT format
* BBT is corrupted and the flash must be rescanned for bad
blocks; we want to remember bad blocks that were marked from Linux
So to keep the bad block markers in sync with the flash-based BBT, this
patch changes the default so that we write bad block markers to the proper
OOB area on each block in addition to flash-based BBT. Comments are
updated, expanded, and/or relocated as necessary.
The new flash-based BBT procedure for marking bad blocks:
(1) erase the affected block, to allow OOB marker to be written cleanly
(2) update in-memory BBT
(3) write bad block marker to OOB area of affected block
(4) update flash-based BBT
Note that we retain the first error encountered in (3) or (4), finish the
procedures, and dump the error in the end.
This should handle power cuts gracefully enough. (1) and (2) are mostly
harmless (note that (1) will not erase an already-recognized bad block).
The OOB and BBT may be "out of sync" if we experience power loss bewteen
(3) and (4), but we can reasonably expect that on next boot, subsequent
I/O operations will discover that the block should be marked bad again,
thus re-syncing the OOB and BBT.
Note that this is a change from the previous default flash-based BBT
behavior. If your system cannot support writing bad block markers to OOB,
use the new NAND_BBT_NO_OOB_BBM option (in combination with
NAND_BBT_USE_FLASH and NAND_BBT_NO_OOB).
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We do not need to invoke 'mtd_can_have_bb()' before invoking
'mtd_block_isbad()' because the latter already handles the case when the MTD
device does not support bad blocks.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd: mtdconcat: return -EOPNOTSUPP if block_markbad is undefined
The main 'mtd_block_markbad()' function returns -EOPNOTSUPP if the
'->block_markbad' method is undefined, and mtdconcat should do the same.
Fix this by simply removing the 'mtd_can_have_bb()' because it is not
really necessary. It could be treated as an optimization, but this function is
expected to be used so rarely that it does not matter.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to the flash page size because it is the maximum amount of
data it writes at a time.
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to the flash page size because it is the maximum amount of
data it writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set writebufsize to 4 because this drivers writes at max 4 bytes at a time.
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Cc: stable@kernel.org [3.2+] Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
Set it to be equivalent to mtd->writesize because this is the maximum amount
of data the driver writes at a time.
The writebufsize concept was introduce by commit
"0e4ca7e mtd: add writebufsize field to mtd_info struct" and it represents
the maximum amount of data the device writes to the media at a time. This is
an important parameter for UBIFS which is used during recovery and which
basically defines how big a corruption caused by a power cut can be.
However, we forgot to set this parameter for block2mtd. Set it to PAGE_SIZE
because this is actually the amount of data we write at a time.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Acked-by: Joern Engel <joern@lazybastard.org> Cc: stable@kernel.org [2.6.38+] Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Dan Carpenter [Tue, 31 Jan 2012 08:54:06 +0000 (11:54 +0300)]
mtd: docg4: fix printk() warnings
Gcc complains here:
drivers/mtd/nand/docg4.c: In function ‘probe_docg4’:
drivers/mtd/nand/docg4.c:1277:4: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘resource_size_t’ [-Wformat]
drivers/mtd/nand/docg4.c:1277:4: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 4 has type ‘resource_size_t’ [-Wformat]
We have a standard way of printing these using a format string
extension.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Wolfram Sang [Tue, 31 Jan 2012 12:10:43 +0000 (13:10 +0100)]
mtd: nand: gpmi: use correct member for checking NAND_BBT_USE_FLASH
This has been moved from .options to .bbt_options meanwhile. So, it
currently checks for something totally different (NAND_OWN_BUFFERS) and
decides according to that.
Artem Bityutskiy: the options were moved in a40f734 mtd: nand: consolidate redundant flash-based BBT flags
Artem Bityutskiy: CCing -stable
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Cc: stable@kernel.org [3.2+] Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The reason is that we are re-working the MTD API and from now on it is
an error to use MTD function pointers directly - we have a corresponding
API call for every pointer. By adding a leading "_" we achieve the following:
1. Make sure we convert every direct pointer users
2. A leading "_" suggests that this interface is internal and it becomes
less likely that people will use them directly
3. Make sure all the out-of-tree modules stop compiling and the owners
spot the big API change and amend them.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Fri, 3 Feb 2012 00:21:09 +0000 (16:21 -0800)]
jffs2: update to new MTD interface
There were a few instances of the old MTD interface remaining for JFFS2. We
fix one error that shows up (only when CONFIG_JFFS2_FS_WRITEBUFFER is not
defined) like this:
fs/jffs2/read.c: In function 'jffs2_read_dnode':
fs/jffs2/read.c:36:8: error: 'struct mtd_info' has no member named 'read'
fs/jffs2/read.c:112:8: error: 'struct mtd_info' has no member named 'read'
...
We also simply remove two macros that are not in use, were not updated to
the new MTD interface, and don't even utilize the old interface properly.
(That means they weren't used since commit 8593fbc6, year 2006; almost 6
years ago, for those who don't want to do the math)
Reported-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Dunn [Wed, 4 Jan 2012 00:05:44 +0000 (16:05 -0800)]
mtd: nand: add support for diskonchip G4 nand flash device
This patch adds a driver for the M-Sys / Sandisk diskonchip G4 nand flash found
in various smartphones and PDAs, among them the Palm Treo680, HTC Prophet and
Wizard, Toshiba Portege G900, Asus P526, and O2 XDA Zinc. It was tested on the
Treo 680, but should work generically.
Since v3, this patch adds power management functions, a scan of the factory bad
block table during initialization, several fixes, and more extensive testing.
Also, the platform data header file, which only contained partitioning
information, was removed. Command-line partitioning can be used, at least until
an mtd parser is written for the saftl format with which these chips are
shipped.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Axel Lin [Fri, 27 Jan 2012 07:45:20 +0000 (15:45 +0800)]
mtd: convert drivers/mtd/* to use module_spi_driver()
This patch converts the drivers in drivers/mtd/* to use the
module_spi_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Sat, 21 Jan 2012 04:38:03 +0000 (20:38 -0800)]
mtd: nand: move SCANLASTPAGE handling to the correct code block
As nand_default_block_markbad() is becoming more complex, it helps to
have code appear only in its relevant codepath(s). Here, the calculation
of `ofs' based on NAND_BBT_SCANLASTPAGE is only useful on paths where we
write bad block markers to OOB. We move the condition/calculation closer
to the `write' operation and update the comment to more correctly
describe the operation.
The variable `wr_ofs' is also used to help isolate our calculation of
the "write" offset from the usage of `ofs' to represent the eraseblock
offset. This will become useful when we reorder operations in the next
patch.
This patch should make no functional change.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtdoops no longer uses a console. Now, if you build it into your kernel,
you add something like the following to your command line to select
partition X as your logging partition:
mtdoops.mtddev=X
Anyway, it seems better to leave the documentation out of Kconfig.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd: sa11x0: remove definitions and code left for documentation purposes
/*
* This is here for documentation purposes only - until these people
* submit their machine types. It will be gone January 2005.
*/
It's now seven years after that date, so let's remove this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit c4a9f88daf ([MTD] [NOR] fix ctrl-alt-del can't reboot for
intel flash bug) interferes with this work-around, causing MTD to
issue this warning:
Flash device refused suspend due to active operation (state 0)
The commit makes our work-around in the map driver unnecessary, so
let's remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Shiraz Hashim [Thu, 12 Jan 2012 13:38:57 +0000 (14:38 +0100)]
mtd: ST SPEAr: Add SMI driver for serial NOR flash
SPEAr platforms (spear3xx/spear6xx/spear13xx) provide SMI (Serial Memory
Interface) controller to access serial NOR flash. SMI provides a simple
interface for SPI/serial NOR flashes and has certain inbuilt commands
and features to support these flashes easily. It also makes it possible
to map an address range in order to directly access (read/write) the SNOR
over address bus. This patch intends to provide serial nor driver support
for spear platforms which are accessed through SMI.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com> Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Sat, 14 Jan 2012 02:11:48 +0000 (18:11 -0800)]
mtd: nand: fix SCAN2NDPAGE check for BBM
nand_block_bad() doesn't check the correct pages when
NAND_BBT_SCAN2NDPAGE is enabled. It should scan both the OOB region of
both the 1st and 2nd page of each block.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Sat, 14 Jan 2012 02:11:47 +0000 (18:11 -0800)]
mtd: nand: erase block before marking bad
Many NAND flash systems (especially those with MLC NAND) cannot be
reliably written twice in a row. For instance, when marking a bad block,
the block may already have data written to it, and so we should attempt
to erase the block before writing a bad block marker to its OOB region.
We can ignore erase failures, since the block may be bad such that it
cannot be erased properly; we still attempt to write zeros to its spare
area.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Julia Lawall [Thu, 12 Jan 2012 09:55:05 +0000 (10:55 +0100)]
mtd: onenand: samsung: add missing iounmap
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Alexander Stein [Tue, 10 Jan 2012 12:26:58 +0000 (13:26 +0100)]
mtd: mtdblock: call mtd_sync() only if opened for write
Because it is useless to call it if the device is opened in R/O mode, and also
harmful: on CFI NOR flash it may block for long time waiting for erase
operations to complete is another partition with a R/W file-system on this
chip.
Artem Bityutskiy: write commit message, amend the patch to match the latest
tree (we use mtd_sync(), not mtd->sync() nowadays).
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Xi Wang [Mon, 9 Jan 2012 21:58:25 +0000 (16:58 -0500)]
mtd: pmc551: fix signedness bug in init_pmc551()
Since "length" is a u32, the error handling below didn't work when
fixup_pmc551() returns -ENODEV.
if ((length = fixup_pmc551(PCI_Device)) <= 0)
This patch changes both the type of "length" and the return type of
fixup_pmc551() to int.
Signed-off-by: Xi Wang <xi.wang@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ira W. Snyder [Fri, 6 Jan 2012 19:29:19 +0000 (11:29 -0800)]
mtd: cfi: AMD/Fujitsu compatibles: add panic write support
This allows the mtdoops driver to work on flash chips using the
AMD/Fujitsu compatible command set.
As the code comments note, the locks used throughout the normal code
paths in the driver are ignored, so that the chance of writing out the
kernel's last messages are maximized.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Linus Torvalds [Sun, 4 Mar 2012 00:33:51 +0000 (16:33 -0800)]
Merge tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6
PARISC fixes from James Bottomley:
"This is a set of build fixes to get the cross compiled architecture
testbeds building again"
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] don't unconditionally override CROSS_COMPILE for 64 bit.
[PARISC] include <linux/prefetch.h> in drivers/parisc/iommu-helpers.h
[PARISC] fix compile break caused by iomap: make IOPORT/PCI mapping functions conditional
Linus Torvalds [Fri, 2 Mar 2012 23:21:48 +0000 (15:21 -0800)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
hhwmon fixes for 3.3-rc6 from Guenter Roeck:
These patches are necessary for correct operation and management of
F75387.
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (f75375s) Catch some attempts to write to r/o registers
hwmon: (f75375s) Properly map the F75387 automatic modes to pwm_enable
hwmon: (f75375s) Make pwm*_mode writable for the F75387
hwmon: (f75375s) Fix writes to the pwm* attribute for the F75387
Linus Torvalds [Fri, 2 Mar 2012 23:21:15 +0000 (15:21 -0800)]
Merge tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6
fbdev fixes for 3.3 from Florian Tobias Schandinat
It includes:
- two fixes for OMAP HDMI
- one fix to make new OMAP functions behave as they are supposed to
- one Kconfig dependency fix
- two fixes for viafb for modesetting on VX900 hardware
* tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6:
OMAPDSS: APPLY: make ovl_enable/disable synchronous
OMAPDSS: panel-dvi: Add Kconfig dependency on I2C
viafb: fix IGA1 modesetting on VX900
viafb: select HW scaling on VX900 for IGA2
OMAPDSS: HDMI: hot plug detect fix
OMAPDSS: HACK: Ensure DSS clock domain gets out of idle when HDMI is enabled
Linus Torvalds [Fri, 2 Mar 2012 23:20:41 +0000 (15:20 -0800)]
Merge tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
sound fixes for 3.3-rc6 from Takashi Iwai
This contains again regression fixes for various HD-audio and ASoC
regarding SSI and dapm shutdown path. In addition, a minor azt3328
fix and the correction of the new jack-notification strings in HD-audio.
* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Kill hyphenated names
ALSA: hda - Add a fake mute feature
ALSA: hda - Always set HP pin in unsol handler for STAC/IDT codecs
ALSA: azt3328 - Fix NULL ptr dereference on cards without OPL3
ALSA: hda/realtek - Fix resume of multiple input sources
ASoC: i.MX SSI: Fix DSP_A format.
ASoC: dapm: Check for bias level when powering down
Linus Torvalds [Fri, 2 Mar 2012 22:49:24 +0000 (14:49 -0800)]
vfs: split up name hashing in link_path_walk() into helper function
The code in link_path_walk() that finds out the length and the hash of
the next path component is some of the hottest code in the kernel. And
I have a version of it that does things at the full width of the CPU
wordsize at a time, but that means that we *really* want to split it up
into a separate helper function.
So this re-organizes the code a bit and splits the hashing part into a
helper function called "hash_name()". It returns the length of the
pathname component, while at the same time computing and writing the
hash to the appropriate location.
The code generation is slightly changed by this patch, but generally for
the better - and the added abstraction actually makes the code easier to
read too. And the new interface is well suited for replacing just the
"hash_name()" function with alternative implementations.
Linus Torvalds [Fri, 2 Mar 2012 22:47:15 +0000 (14:47 -0800)]
vfs: clarify and clean up dentry_cmp()
It did some odd things for unclear reasons. As this is one of the
functions that gets changed when doing word-at-a-time compares, this is
yet another of the "don't change any semantics, but clean things up so
that subsequent patches don't get obscured by the cleanups".
Linus Torvalds [Fri, 2 Mar 2012 22:32:59 +0000 (14:32 -0800)]
vfs: uninline full_name_hash()
.. and also use it in lookup_one_len() rather than open-coding it.
There aren't any performance-critical users, so inlining it is silly.
But it wouldn't matter if it wasn't for the fact that the word-at-a-time
dentry name patches want to conditionally replace the function, and
uninlining it sets the stage for that.
So again, this is a preparatory patch that doesn't change any semantics,
and only prepares for a much cleaner and testable word-at-a-time dentry
name accessor patch.
Linus Torvalds [Fri, 2 Mar 2012 22:23:30 +0000 (14:23 -0800)]
vfs: trivial __d_lookup_rcu() cleanups
These don't change any semantics, but they clean up the code a bit and
mark some arguments appropriately 'const'.
They came up as I was doing the word-at-a-time dcache name accessor
code, and cleaning this up now allows me to send out a smaller relevant
interesting patch for the experimental stuff.
Nikolaus Schulz [Tue, 28 Feb 2012 21:15:54 +0000 (16:15 -0500)]
hwmon: (f75375s) Catch some attempts to write to r/o registers
It makes no sense to attempt to manually configure the fan in auto mode,
or set the duty cycle directly in closed loop mode. The corresponding
registers are then read-only. If the user tries it nonetheless, error out
with EINVAL instead of silently doing nothing.
Nikolaus Schulz [Tue, 28 Feb 2012 21:15:53 +0000 (16:15 -0500)]
hwmon: (f75375s) Properly map the F75387 automatic modes to pwm_enable
The F75387 supports automatic fan control using either PWM duty cycle or
RPM speed values. Make the driver detect the latter mode, and expose the
different modes in sysfs as per pwm_enable, so that the user can switch
between them.
The interpretation of the pwm_enable attribute for the F75387 is adjusted
to be a superset of those values used for similar Fintek chips which do
not support automatic duty mode, with 2 mapping to automatic speed mode,
and moving automatic duty mode to the new value 4.
Toggling the duty mode via pwm_enable is currently denied for the F75387,
as the chip then simply reinterprets the fan configuration register values
according to the new mode, switching between RPM and PWM units, which
makes this a dangerous operation.
This patch introduces a new pwm mode into the driver. This is necessary
because the new mode (automatic pwm mode, 4) may already be enabled by the
BIOS, and the driver should not break existing functionality. This was seen
on at least one board.
Linus Torvalds [Fri, 2 Mar 2012 19:38:43 +0000 (11:38 -0800)]
Merge branches 'core-urgent-for-linus', 'perf-urgent-for-linus' and 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pulling latest branches from Ingo:
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
memblock: Fix size aligning of memblock_alloc_base_nid()
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Ensure offset provided is not greater than function length without DWARF info too
perf tools: Ensure comm string is properly terminated
perf probe: Ensure offset provided is not greater than function length
perf evlist: Return first evsel for non-sample event on old kernel
perf/hwbp: Fix a possible memory leak
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
CPU hotplug, cpusets, suspend: Don't touch cpusets during suspend/resume
H. Peter Anvin [Fri, 2 Mar 2012 18:43:49 +0000 (10:43 -0800)]
regset: Return -EFAULT, not -EIO, on host-side memory fault
There is only one error code to return for a bad user-space buffer
pointer passed to a system call in the same address space as the
system call is executed, and that is EFAULT. Furthermore, the
low-level access routines, which catch most of the faults, return
EFAULT already.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Roland McGrath <roland@hack.frob.com> Cc: <stable@vger.kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
H. Peter Anvin [Fri, 2 Mar 2012 18:43:48 +0000 (10:43 -0800)]
regset: Prevent null pointer reference on readonly regsets
The regset common infrastructure assumed that regsets would always
have .get and .set methods, but not necessarily .active methods.
Unfortunately people have since written regsets without .set methods.
Rather than putting in stub functions everywhere, handle regsets with
null .get or .set methods explicitly.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Roland McGrath <roland@hack.frob.com> Cc: <stable@vger.kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joerg Roedel [Wed, 29 Feb 2012 13:57:32 +0000 (14:57 +0100)]
perf/x86/kvm: Fix Host-Only/Guest-Only counting with SVM disabled
It turned out that a performance counter on AMD does not
count at all when the GO or HO bit is set in the control
register and SVM is disabled in EFER.
This patch works around this issue by masking out the HO bit
in the performance counter control register when SVM is not
enabled.
The GO bit is not touched because it is only set when the
user wants to count in guest-mode only. So when SVM is
disabled the counter should not run at all and the
not-counting is the intended behaviour.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Avi Kivity <avi@redhat.com> Cc: Stephane Eranian <eranian@google.com> Cc: David Ahern <dsahern@gmail.com> Cc: Gleb Natapov <gleb@redhat.com> Cc: Robert Richter <robert.richter@amd.com> Cc: stable@vger.kernel.org # v3.2 Link: http://lkml.kernel.org/r/1330523852-19566-1-git-send-email-joerg.roedel@amd.com Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Fri, 2 Mar 2012 02:27:43 +0000 (18:27 -0800)]
Merge git://www.linux-watchdog.org/linux-watchdog
Watchdog updates from Wim Van Sebroeck:
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: fix GETTIMEOUT ioctl in booke_wdt
watchdog: update maintainers git entry
watchdog: Fix typo in pnx4008_wdt.c
watchdog: Fix typo in Kconfig
watchdog: fix error in probe() of s3c2410_wdt (reset at booting)
watchdog: hpwdt: clean up set_memory_x call for 32 bit
Linus Torvalds [Fri, 2 Mar 2012 02:26:48 +0000 (18:26 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull from Mark Brown:
"A simple, driver specific fix. This device isn't widely used outside
of Marvell reference boards most of which are probably used with their
BSPs rather than with mainline so low risk."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: fix the ldo configure according to 88pm860x spec
Linus Torvalds [Fri, 2 Mar 2012 02:24:52 +0000 (18:24 -0800)]
Merge branch 'i2c-embedded/for-3.3' of git://git.pengutronix.de/git/wsa/linux-2.6
i2c bugfix from Wolfram Sang:
"This patch fixes a wrong assumption in the mxs-i2c-driver about a
command queue being done. Without it, we have seen races when the
bus was under load."
* 'i2c-embedded/for-3.3' of git://git.pengutronix.de/git/wsa/linux-2.6:
i2c: mxs: only flag completion when queue is completely done
Linus Torvalds [Fri, 2 Mar 2012 02:23:43 +0000 (18:23 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
DRM fixes from Dave Airlie:
intel: fixes for output regression on 965GM, an oops and a machine
hang
radeon: uninitialised var (that gcc didn't warn about for some reason)
+ a couple of correctness fixes.
exynos: fixes for various things, drop some chunks of unused code.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/vm: fix possible bug in radeon_vm_bo_rmv()
drm/radeon: fix uninitialized variable
drm/radeon/kms: fix radeon_dp_get_modes for LVDS bridges (v2)
drm/i915: Remove use of the autoreported ringbuffer HEAD position
drm/i915: Prevent a machine hang by checking crtc->active before loading lut
drm/i915: fix operator precedence when enabling RC6p
drm/i915: fix a sprite watermark computation to avoid divide by zero if xpos<0
drm/i915: fix mode set on load pipe. (v2)
drm/exynos: exynos_drm.h header file fixes
drm/exynos: added panel physical size.
drm/exynos: added postclose to release resource.
drm/exynos: removed exynos_drm_fbdev_recreate function.
drm/exynos: fixed page flip issue.
drm/exynos: added possible_clones setup function.
drm/exynos: removed pageflip_event_list init code when closed.
drm/exynos: changed priority of mixer layers.
drm/exynos: Fix typo in exynos_mixer.c
Linus Torvalds [Fri, 2 Mar 2012 02:22:55 +0000 (18:22 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] memory hotplug: prevent memory zone interleave
[S390] crash_dump: remove duplicate include
[S390] KEYS: Enable the compat keyctl wrapper on s390x
Takashi Iwai [Thu, 1 Mar 2012 13:17:07 +0000 (14:17 +0100)]
Merge tag 'asoc-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
A small fix for the SSI driver and a fix for system shutdown with modern
devices. Most of the modern devices will never get shut down normally
with a visible kernel log as the systems they're in tend not to shut
down often and when they do it's usually in form factors that don't have
a user visible console.
Tejun Heo [Tue, 28 Feb 2012 20:56:21 +0000 (05:56 +0900)]
memblock: Fix size aligning of memblock_alloc_base_nid()
memblock allocator aligns @size to @align to reduce the amount
of fragmentation. Commit:
7bd0b0f0da ("memblock: Reimplement memblock allocation using reverse free area iterator")
Broke it by incorrectly relocating @size aligning to
memblock_find_in_range_node(). As the aligned size is not
propagated back to memblock_alloc_base_nid(), the actually
reserved size isn't aligned.
While this increases memory use for memblock reserved array,
this shouldn't cause any critical failure; however, it seems
that the size aligning was hiding a use-beyond-allocation bug in
sparc64 and losing the aligning causes boot failure.
The underlying problem is currently being debugged but this is a
proper fix in itself, it's already pretty late in -rc cycle for
boot failures and reverting the change for debugging isn't
difficult. Restore the size aligning moving it to
memblock_alloc_base_nid().
Reported-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Tejun Heo <tj@kernel.org> Cc: David S. Miller <davem@davemloft.net> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Rob Herring <rob.herring@calxeda.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Link: http://lkml.kernel.org/r/20120228205621.GC3252@dhcp-172-17-108-109.mtv.corp.google.com Signed-off-by: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <alpine.SOC.1.00.1202130942030.1488@math.ut.ee>
Amit Shah [Wed, 29 Feb 2012 12:12:51 +0000 (17:42 +0530)]
virtio: balloon: leak / fill balloon across S4
commit e562966dbaf49e7804097cd991e5d3a8934fc148 added support for S4 to
the balloon driver. The freeze function did nothing to free the pages,
since reclaiming the pages from the host to immediately give them back
(if S4 was successful) seemed wasteful. Also, if S4 wasn't successful,
the guest would have to re-fill the balloon. On restore, the pages were
supposed to be marked freed and the free page counters were incremented
to reflect the balloon was totally deflated.
However, this wasn't done right. The pages that were earlier taken away
from the guest during a balloon inflation operation were just shown as
used pages after a successful restore from S4. Just a fancy way of
leaking lots of memory.
Instead of trying that, just leak the balloon on freeze and fill it on
restore/thaw paths. This works properly now. The optimisation to not
leak can be added later on after a bit of refactoring of the code.
Signed-off-by: Amit Shah <amit.shah@redhat.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tomi Valkeinen [Wed, 29 Feb 2012 08:48:22 +0000 (10:48 +0200)]
OMAPDSS: APPLY: make ovl_enable/disable synchronous
ovl->enable/disable are meant to be synchronous so that they can handle
the configuration of fifo sizes. The current kernel doesn't configure
fifo sizes yet, and so the code doesn't need to block to function (from
omapdss driver's perspective).
However, for the users of omapdss a non-blocking ovl->disable is
confusing, because they don't know when the memory area is not used
any more.
Furthermore, when the fifo size configuration is added in the next merge
window, the change from non-blocking to blocking could cause side
effects to the users of omapdss. So by making the functions block
already will keep them behaving in the same manner.
And, while not the main purpose of this patch, this will also remove the
compile warning:
drivers/video/omap2/dss/apply.c:350: warning:
'wait_pending_extra_info_updates' defined but not used
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
perf probe: Ensure offset provided is not greater than function length without DWARF info too
The 'perf probe' command allows kprobe to be inserted at any offset from
a function start, which results in adding kprobes to unintended
location. (example: perf probe do_fork+10000 is allowed even though
size of do_fork is ~904).
My previous patch https://lkml.org/lkml/2012/2/24/42 addressed the case
where DWARF info was available for the kernel. This patch fixes the
case where perf probe is used on a kernel without debuginfo available.
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com> Cc: Jason Baron <jbaron@redhat.com> Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Andrew Morton <akpm@linux-foundation.org> Link: http://lkml.kernel.org/r/4F4C544D.1010909@linux.vnet.ibm.com Signed-off-by: Prashanth Nageshappa <prashanth@linux.vnet.ibm.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
David Ahern [Fri, 24 Feb 2012 19:31:38 +0000 (12:31 -0700)]
perf tools: Ensure comm string is properly terminated
If threads in a multi-threaded process have names shorter than the main
thread the comm for the named threads is not properly terminated.
E.g., for the process 'namedthreads' where each thread is named noploop%d
where %d is the thread number:
Before:
perf script -f comm,tid,ip,sym,dso
noploop:4ads 21616 400a49 noploop (/tmp/namedthreads)
The 'ads' in the thread comm bleeds over from the process name.
Namhyung Kim [Mon, 20 Feb 2012 01:47:26 +0000 (10:47 +0900)]
perf evlist: Return first evsel for non-sample event on old kernel
On old kernels that don't support sample_id_all feature,
perf_evlist__id2evsel() returns NULL for non-sampling events.
This breaks perf top when multiple events are given on command line. Fix
it by using first evsel in the evlist. This will also prevent getting
the same (potential) problem in such new tool/ old kernel combo.
Suggested-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/1329702447-25045-1-git-send-email-namhyung.kim@lge.com Signed-off-by: Namhyung Kim <namhyung.kim@lge.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Wed, 29 Feb 2012 19:24:39 +0000 (11:24 -0800)]
Merge tag 'fixes-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Arnd Bergmann says:
"Another set of arm-soc bug fixes on top of v3.3-rc5. The few larger
bits are all for devices that still need to get set up in board code.
Only three platforms are in this set of fixes: omap2+, pxa and lpc32xx."
* tag 'fixes-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
ARM: LPC32xx: serial.c: Fixed loop limit
ARM: LPC32xx: serial.c: HW bug workaround
ARM: LPC32xx: irq.c: Clear latched event
ARM: LPC32xx: Fix interrupt controller init
ARM: LPC32xx: Fix irq on GPI_28
ARM: OMAP2: fix mailbox init code
ARM: OMAP2+: gpmc-smsc911x: add required smsc911x regulators
ARM: OMAP1: Fix out-of-bounds array access for Innovator
OMAP3 EVM: remove out-of-bounds array access of gpio_leds
ARM: OMAP: Fix build error when mmc_omap is built as module
ARM: OMAP: Fix kernel panic with HSMMC when twl4030_gpio is a module
pxa/hx4700: add platform device and I2C info for AK4641 codec
arch/arm/mach-pxa/: included linux/gpio.h twice
arch/arm/mach-mmp/: some files include some headers twice
ARM: pxa: fix error handling in pxa2xx_drv_pcmcia_probe
ARM: pxa: fix including linux/gpio.h twice
ARM: pxa: fix mixed declarations and code in sharpsl_pm
ARM: pxa: fix wrong parsing gpio event on spitz
ARM: OMAP2+: usb-host: fix compile warning
ARM: OMAP4: Move the barrier memboclk_steal() as part of reserve callback
...
drm/radeon/kms/vm: fix possible bug in radeon_vm_bo_rmv()
The bo is removed from the list at the top of
radeon_vm_bo_rmv(), but then the list is used
in radeon_vm_bo_update_pte() to look up the vm.
remove the bo_list entry at the end of the
function instead.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Jerome Glisse <j.glisse@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Takashi Iwai [Mon, 27 Feb 2012 14:00:58 +0000 (15:00 +0100)]
ALSA: hda - Add a fake mute feature
Some codecs don't supply the mute amp-capabilities although the lowest
volume gives the mute. It'd be handy if the parser provides the mute
mixers in such a case.
This patch adds an extension amp-cap bit (which is used only in the
driver) to represent the min volume = mute state. Also modified the
amp cache code to support the fake mute feature when this bit is set
but the real mute bit is unset.
In addition, conexant cx5051 parser uses this new feature to implement
the missing mute controls.
Christian König [Tue, 28 Feb 2012 22:19:20 +0000 (23:19 +0100)]
drm/radeon: fix uninitialized variable
Without this fix the driver randomly treats
textures as arrays and I'm really wondering
why gcc isn't complaining about it.
Signed-off-by: Christian König <deathsimple@vodafone.de> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
projects / mv-sheeva.git / log