Some people pointed out to me that it might be helpful to add stubs for
the newly added multicast exports. That way e.g. batman-adv should continue
to be compile and useable without having to have a kernel compiled
with bridge code in the future. This is what the first patch is supposed
to do.
The second patch adds a third multicast export for the bridge which
e.g. batman-adv is supposed to use, too, soon: Just like the bridge
disables its multicast snooping activities if no querier is present,
batman-adv needs to do the same if bridges are involved.
These three exports should be the final ones needed to marry the bridge
multicast snooping with the batman-adv multicast optimizations recently
added for the 3.15 kernel, allowing to use these optimzations in common
setups having a bridge on top of e.g. bat0, too. So far these bridged
setups would fall back to simple flooding through the batman-adv mesh
network for any multicast packet entering bat0.
More information about the batman-adv multicast optimizations currently
implemented can be found here:
bridge: export knowledge about the presence of IGMP/MLD queriers
With this patch other modules are able to ask the bridge whether an
IGMP or MLD querier exists on the according, bridged link layer.
Multicast snooping can only be performed if a valid, selected querier
exists on a link.
Just like the bridge only enables its multicast snooping if a querier
exists, e.g. batman-adv too can only activate its multicast
snooping in bridged scenarios if a querier is present.
For instance this export avoids having to reimplement IGMP/MLD
querier message snooping and parsing in e.g. batman-adv, when
multicast optimizations for bridged scenarios are added in the
future.
Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
To make users (e.g. batman-adv soon) load- and runnable even if the
bridge was compiled without snooping capabilities - or even if the
kernel was compiled without any bridge code at all.
Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
If data is sent on a nonblocking socket and the destination link
is congested, the buffer chain is leaked. We fix this by freeing
the chain in this case.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes issues with debug printk calls across the driver, normally
disabled; first compilation errors:
drivers/net/fddi/defxx.c:676:1: error: pasting "(" and ""In dfx_bus_init...\n"" does not give a valid preprocessing token
drivers/net/fddi/defxx.c:820:1: error: pasting "(" and ""In dfx_bus_uninit...\n"" does not give a valid preprocessing token
and so on, and then warnings:
drivers/net/fddi/defxx.c: In function 'dfx_driver_init':
drivers/net/fddi/defxx.c:1132: warning: format '%0X' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
drivers/net/fddi/defxx.c:1132: warning: format '%0X' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
etc. Additionally casts are removed from virtual addresses and %p used.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 8 Jul 2014 22:30:37 +0000 (15:30 -0700)]
Merge branch 'defxx-next'
Maciej W. Rozycki says:
====================
defxx: Fixes for 64-bit host support
This mini patch series addresses issues with 64-bit host support for FDDI
interface boards supported by the defxx driver where DMA mapping
synchronisation is required on swiotlb systems. While PDQ, the DMA engine
chip used with these boards, supports 48-bit addressing that would
normally suffice for typical 64-bit systems in existence, the host bus
interface chips used by individual implementations have their limitations
as follows:
* DEFTA or DEC FDDIcontroller/TURBOchannel -- there's no host bus
interface chip, the PDQ connects to TURBOchannel directly; TURBOchannel
supports DMA addressing of up to 16GB (34-bit addressing), however no
TURBOchannel system has ever been made that supports more than 1GB of
RAM, so in reality no remapping is ever required,
* DEFEA or DEC FDDIcontroller/EISA -- the ESIC EISA interface chip only
supports 32-bit addressing, all accesses beyond 4GB have to be remapped,
* DEFPA or DEC FDDIcontroller/PCI -- the PFI PCI interface chip rev. 1 & 2
only support 32-bit addressing, they have 32 AD lines only both on the
PDQ and the PCI side, and consequently no Dual Address Cycle support, so
all accesses beyond 4GB have to be remapped; the range of addressing
supported by PFI rev. 3 is currently not certain, however the chip is
backwards compatible with earlier revisions and will work with code that
supports them.
Some other issues discovered in the course of correcting 64-bit support
have been fixed as well. Each of the patches is functionally
self-contained and can be applied independentely, although there may be
mechanical dependencies making it necessary to apply patches in order.
The driver suffers from non-standard formatting and while I did my best
with these bug fixes to follow our coding style, I found some pieces
hopeless, checkpatch.pl will complain. I plan to reformat the whole
driver, that will inevitably require factoring out some pieces into
separate functions, but that's going to be a major effort and therefore I
want to do this separately, with no functional changes made at the same
time. If anyone has specific suggestions as to how to reformat any of the
pieces submitted here for a better layout, then I'll be happy to take them
into account.
And last but not least many thanks to Robert Coerver, who was the most
recent person to report this problem with the driver and was kind enough
to patiently try a few revisions of the driver update on his system as I
was finding and addressing issues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds DMA synchronisation calls needed in the receive path:
1. To retrieve the Receive Status word that is prepended by the PDQ DMA
engine in the receive buffer, and provides information about the
frame received, including its size and any errors.
2. To make data received available for copying in the small-frame case
(size <= SKBUFF_RX_COPYBREAK) where the original DMA buffer will be
returned to the receive descriptor ring and therefore its mapping
retained.
With DMA mapping error handling in place, added by the other patch,
this may now also trigger where an attempt to map a newly allocated
buffer for DMA has failed. In that case data from the original buffer
will be copied out and the buffer returned to the DMA descriptor ring.
These calls may do nothing when data is in the host DMA addressing range
of the FDDI interface, such as always on 32-bit systems, however their
absence makes frame reception stop functioning reliably on systems that
have memory beyond the low 4GB of the address space.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu> Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu> Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This adds error handling for DMA mapping requests; I think there isn't
much else to say about it.
A good side-effect is the mapping in the transmit path is now made with
the board lock released. Also if DMA mapping fails for a newly
allocated receive buffer, then data from the old buffer will be copied
out (as is presently done for small frames only whose size does not
exceed SKBUFF_RX_COPYBREAK) and the original buffer returned, with its
mapping unchanged, to the DMA descriptor ring.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu> Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu> Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the two remaining places across the driver that use dev_alloc_skb
to netdev_alloc_skb. Another place has already been converted to use
__netdev_alloc_skb, no idea why these two have been left behind.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu> Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu> Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Prearranged receive DMA bounce buffer mappings are not released in the
card reboot/shutdown path. That does not affect frame reception, but
probably explains the random segmentation fault I observed the other day
on interface shutdown. Card is rebooted as required by the spec in the
process of ring fault recovery when a PC Trace signal has been received.
This change fixes the problem in an obvious manner.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu> Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu> Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Receive DMA maps are oversized, they include EISA legacy 128-byte
alignment padding in size calculation whereas this padding is never used
for data. Worse yet, if the skb's data area has been realigned indeed,
then data beyond the end of the buffer will be synchronised from the
receive DMA bounce buffer, possibly corrupting data structures residing
in memory beyond the actual end of this data buffer.
Therefore switch to using PI_RCV_DATA_K_SIZE_MAX rather than NEW_SKB_SIZE
in DMA mapping, the value the former macro expands to is written to the
receive ring DMA descriptor of the PDQ DMA chip and determines the
maximum amount of data PDQ will ever transfer to the corresponding data
buffer, including all headers and padding.
Reported-by: Robert Coerver <Robert.Coerver@ll.mit.edu> Tested-by: Robert Coerver <Robert.Coerver@ll.mit.edu> Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 8 Jul 2014 21:39:09 +0000 (14:39 -0700)]
Merge branch 'sctp_command_queue'
David Laight says:
====================
net: sctp: Optimisations to sctp command queue code
These 3 patches optimise the code that processes sctp's command queue.
(A list of 'tasks' to be performed after the rest of the chunk processing.)
1) Inline all the functions from command.c
2) Remove the memset() calls used to zero a word-sized union.
3) Use pointers instead of array indexes.
The combined changes reduce the code size (amd64) by a few kb.
I'm not 100% convinced that the zeroing done in patch 2 is needed at all.
On BE systems it is likely to generate more code than on LE ones.
In fact it might be best to change the union to only contain 'long' sized
items.
Changes for v2:
- Add some missing initialisers in patch 2/3 and delete them in 3/3.
- Modify the commit message for 2/3 to point out that the union
shouldn't need to be zeroed, but the patches aren't intended to
change the behaviour even if the code is buggy.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Laight [Fri, 4 Jul 2014 14:35:51 +0000 (14:35 +0000)]
net: sctp: Optimise the way 'sctp_arg_t' values are initialised.
Even if memset() is inlined (as on x86) using it to zero the union
generates a memory word write of zero, followed by a write of the
smaller field, and then a read of the word.
As well as being a lot of instructions the sequence is unlikely to
be optimised by the store-load forward hardware so will be slow.
Instead allocate a field of the union that is the same size as the
entire union and write a zero value to it. The compiler will then
generate the required value in a register.
Zeroing the union shouldn't be necessary, but this patch series isn't
intended to have a behavioural change.
Signed-off-by: David Laight <david.laight@aculab.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Laight [Fri, 4 Jul 2014 14:35:51 +0000 (14:35 +0000)]
net: sctp: Inline the functions from command.c
sctp_init_cmd_seq() and sctp_next_cmd() are only called from one place.
The call sequence for sctp_add_cmd_sf() is likely to be longer than
the inlined code.
With sctp_add_cmd_sf() inlined the compiler can optimise repeated calls.
Signed-off-by: David Laight <david.laight@aculab.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Please pull this first batch of wireless updates intended for the
3.17 stream...
For the mac80211 bits, Johannes says:
"The biggest thing here is probably Arik's TDLS rework, beyond that we
have smaller improvements and features like David's scanning IE thing,
Luca's queue work, some CSA work, etc. Also your PID rate control
removal, of course."
For the iwlwifi bits, Emmanuel says:
"I have here a whole bunch of various things. Andy contributes
better debug prints for dvm specific flows and a module parameter to
completely disable power save for dvm. Andrei is sharing the premises
of his work on CSA - more to come. Eran and Liad keep on working
on the new devices. I have the regular amount of BT Coex stuff and
I continue to work on the firmware error report system adding more
debug capabilities. More to come on that subject too."
On top of that, there are some cleanups to the new rsi driver, some
continuing improvements to the rtl818x drivers, and the usual bundles
of updates to ath9k, b43, mwifiex, wil6210, and a few other bits here
and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
load_pointer() is already a static inline function.
Let's move it into filter.h so BPF JIT implementations can reuse this
function.
Since we're exporting this function, let's also rename it to
bpf_load_pointer() for clarity.
Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com> Reviewed-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Alexei Starovoitov <ast@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/amd/declance.c: In function 'lance_init_ring':
drivers/net/ethernet/amd/declance.c:478: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:487: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:503: warning: cast from pointer to integer of different size
drivers/net/ethernet/amd/declance.c:520: warning: cast from pointer to integer of different size
in 64-bit compilation. Where the value printed is an offset (whose range
will always fit) the cast uses a 32-bit type, otherwise, where it is a
host memory address, the pointer is output directly with %p. Also the
remaining `0x' prefix is dropped for consistency across these messages.
Tested with both 32-bit and 64-bit compilation, as well as at the run time
(with the debug messages affected enabled).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 8 Jul 2014 18:36:08 +0000 (11:36 -0700)]
Merge branch 'hsr-next'
Arvid Brodin says:
====================
net/hsr: Use list_head+rcu, better frame dispatch, etc.
This patch series is meant to improve the HSR code in several ways:
* Better code readability.
* In general, make the code structure more like the net/bridge code (HSR
operates similarly to a bridge, but uses the HSR-specific frame headers to
break up rings, instead of the STP protocol).
* Better handling of HSR ports' net_device features.
* Use list_head and the _rcu list traversing routines instead of array of slave
devices.
* Make it easy to support HSR Interlink devices (for future Redbox/Quadbox
support).
* Somewhat better throughput on non-HAVE_EFFICIENT_UNALIGNED_ACCESS archs, due
to lesser copying of skb data.
The code has been tested in a ring together with other HSR nodes running
unchanged code, on both avr32 and x86_64. There should only be one minor change
in behaviour from a user perspective:
* Anyone using the Netlink HSR_C_GET_NODE_LIST message to dump the internal
node database will notice that the database now also contains the self node.
All patches pass 'checkpatch.pl --ignore CAMELCASE --max-line-length=83
--strict' with only CHECKs, each of which have been deliberately left in place.
The final code passes sparse checks with no output.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the separate paths for frames coming from the outside, and
frames sent from the HSR device, and instead makes all frames go through
hsr_forward_skb() in hsr_forward.c. This greatly improves code readability and
also opens up the possibility for future support of the HSR Interlink device
that is the basis for HSR RedBoxes and HSR QuadBoxes, as well as VLAN
compatibility.
Other improvements:
* A reduction in the number of times an skb is copied on machines without
HAVE_EFFICIENT_UNALIGNED_ACCESS, which improves throughput somewhat.
* Headers are now created using the standard eth_header(), and using the
standard hard_header_len.
* Each HSR slave now gets its own private skb, so slave-specific fields can be
correctly set.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Also try to prevent some possible slave dereference race conditions. This is
finalized in the next patch, which abandons the slave array in favour of
a list_head list and list RCU.
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se> Signed-off-by: David S. Miller <davem@davemloft.net>
When the system is too busy to complete the urb, the tx timout function
would be called. This causes the other tx urbs would be killed, too.
Increase the tx timeout to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: netdev@vger.kernel.org Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: David S. Miller <davem@davemloft.net>
The following series fixes some bugs and provides new/changed support
in the driver.
- Fix a debugfs backward compatibility issue introduced by a previous patch
- Write to the interrupt enablement register, not the status register when
setting MTL interrupts
- Call netif_napi_del whenever the ndo_stop operation is called (to match
the call to netif_napi_add on ndo_open)
- Peformance enhancements:
- Adjusted default coalescing settings
- AXI DMA changes (burst length size and cache settings)
- ioread/iowrite reduction during interrupt
- Napi poll updates
- AXI DMA settings based on device tree property to account for a change in
the ARM64 default cache operations assignment
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
amd-xgbe: Base AXI DMA cache settings on device tree
The default cache operations for ARM64 were changed during 3.15.
To use coherent operations a "dma-coherent" device tree property
is required. If that property is not present in the device tree
node then the non-coherent operations are assigned for the device.
Add support to the amd-xgbe driver to assign the AXI DMA cache settings
based on whether the "dma-coherent" property is present in the device
node. If present, use settings that work with the caches. If not
present, use settings that do not look at the caches.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides some general performance enhancements for the
driver:
- Modify the default coalescing settings (reduce usec, increase frames)
- Change the AXI burst length to 256 bytes (default was 16 bytes which
was smaller than a cache line)
- Change the AXI cache settings to write-back/write-allocate which
allocate cache entries for received packets during the DMA since the
packet will be processed soon afterwards
- Combine ioread/iowrite when disabling both the Tx and Rx interrupts
- Change to processing the Tx/Rx channels in pairs
- Only recycle the Rx descriptors when a threshold of dirty descriptors
is reached
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
amd-xgbe: Call netif_napi_del on ndo_stop operation
Currently the napi context is added using netif_napi_add each time
the ndo_open operation is called. However, there is not a
corresponding netif_napi_del call during the ndo_stop operation. If
the device ndo_open operation was called more than once an infinite
loop occurs during module unload. Add a call to netif_napi_del during
the ndo_stop operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing the MTL interrupts the interrupt status
register is written to instead of the interrupt enable register.
Since no MTL interrupts are being enabled and the default state
is for MTL interrupts to be disabled this did not cause a problem,
but needs to be fixed to target the correct register.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
amd-xgbe: Fix debugfs compatibility change with kstrtouint
The initial change from sscanf to kstrtouint broke backward
compatbility by using a base of "0" in the kstrtouint call.
This allowed for entering decimal, hexadecimal or octal as
input where previously the sscanf always interpreted the input
as hexadecimal. Additionally, -EIO was returned on error prior
to this change and now it is whatever the error value that is
returned by kstrtouint.
Change the base value of the kstrtouint from 0 to 16 and return
-EIO on error.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Reported-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The header file include/linux/arcdevice.h #defines bool to int, if
bool is not already #defined. However, the files which use that header
file seem to rely on that #define (unconditionally) being in effect:
the prototypes for the functions arcrimi_reset, com20020_reset,
com90io_reset, com90xx_reset (whose addresses are assigned to the
hw.reset member of struct arcnet_local) use int explicitly.
Moreover, that #define is an accident waiting to happen (scenario:
inclusion of arcdevice.h followed by inclusion of some header which
declares function prototypes using bool). Also, #include
<linux/types.h> must appear before #include <linux/arcdevice.h> (the
compiler wouldn't like "typedef _Bool int").
Since none of the files using arcdevice.h declare variables of type
"bool", the patch is actually quite simple, unlike the commit message.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
* It should return -EINVAL and not -EOPNOTSUPP for invalid coalesce values.
* In case of MSIX, enic_set_coalesce return error after applying requested
coalescing setting partially. We should either apply all the setting requeste
and return success or apply non and return error.
* This patch also simplifies the algo.
This was introduced by
'7c2ce6e60f703 enic: Add support for adaptive interrupt coalescing'
These changes were suggested by Ben Hutchings here
http://www.spinics.net/lists/netdev/msg283972.html
Also change enic driver version.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings are no longer relevant. Even when last slave is
removed, there is a valid address assigned to bond (random).
The correct functionality of vlans is ensured by maintaining unicast
list in vlan_sync_address().
Suggested-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Jiri Pirko <jiri@resnulli.us> Acked-by: Veaceslav Falico <vfalico@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
this patch series includes a rework of the at86rf230 driver.
There are several changes:
- Add regmap support.
- Merge at86rf212 operations with generic at86rf2xx operations, all chips
supports these operations.
- Drop of irqworker. This is a workqueue which will scheduled by an irq to
handle synchronous spi handling. Instead using asynchronous spi handling,
then no scheduler is involved at irq handling.
- Also detected some bugs by receiving frame like CRC can be correct and a
802.15.4 frame length could be above 127 bytes. This would crash the whole
kernel (but should be handled by the mac layer). Another bug is the handling
with RX_SAFE_MODE which protect the frame buffer after a readout. This is
currently not working because we read out the buffer twice and the first one
to get the frame size. Solution is to readout always the whole frame buffer.
- Added some timing relevants things from the datasheet for state changes And
IEEE 802.15.4 standard like interframe spacing. Interframe spacing is needed
to insert some receiving space time between frame transmitting. This should be
also handled by MAC layer, but it's currently a workaround to add this inside
the driver layer.
- Add some callback setting for chip specific handling, instead of runtime decisions
if (is_chip_type()). Callbacks are set only once at probe time.
- We don't using a force state change anymore. A force state change will do a
abort of receiving frames while we want to transmit a new frame. This should
decrease the drop rate of packets.
- And many others changes and bug fixes...
changes since v3:
- fix irq polarity in patch ("at86rf230: rework irq_pol setting").
changes since v2:
- add check if necessary functions are implemented when hw flags are set in patch
("mac802154: at86rf230: add hw flags and merge ops"). I choosed the second variant.
- remove unnecessary includes for workqueue and mutex in patch
("at86rf230: rework transmit and receive").
- remove unnecessary cast in patch ("at86rf230: rework transmit and receive").
- acivate regmap cache with REGCACHE_RBTREE in patch
("at86rf230: add regmap support").
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 2 Jul 2014 22:20:51 +0000 (00:20 +0200)]
at86rf230: rework state change and start/stop
This patch removes the current synchron state change function and add a
new function for a state assert. Change the start and stop callbacks to
use this new synchron state change behaviour. It's a wrapper around the
async state change function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 2 Jul 2014 22:20:48 +0000 (00:20 +0200)]
at86rf230: rework transmit and receive handling
This patch is a complete reimplementation of transmit and receive
handling for the at86rf230 driver.
It solves also six bugs:
First:
The RX_SAFE_MODE is enabled and the transceiver doesn't leave the
receive state while the framebuffer isn't read by a CMD_FB command.
This is useful to read out the frame and don't get into another receive
or transmit state, otherwise the frame would be overwritten.
The current driver do twice CMD_FB calls, the first one leaves this
protection.
Second:
Sometimes the CRC calculation is correct and the length field is greater
127. The current mac802154 layer and filter of a at86rf2xx doesn't check
on this and the kernel crashes. In this case the frame is corrupted, we
send the whole receive buffer to the next layer which can be useful for
sniffing.
Thrid:
There is a undocumented race condition. When we are go into the
RX_AACK_ON state the transceiver could be changed into RX_AACK_BUSY
state. This is a normal behaviour. In this case the transceiver received
a SHR while assert wasn't finished.
Fourth:
It also handle some more "correct" state changes. In aret mode the
transceiver need to go to TX_ON before the transceiver go into
RX_AACK_ON.
Fifth:
The programming model [0] describes also a error handling in ARET mode
if the trac status is different than zero. This is patch adds support
for handling this.
Sixth:
In receive handling the transceiver should also get the trac status
according [0]. The driver could use the trac status as error statistic
handling, but the driver doesn't use this currently. There is maybe some
timing behaviour or the read of this register change some transceiver
states.
In addition the irqworker is removed. Instead we do async spi calls and
no scheduling is involved anymore. The transmit function is also
asynchron but with a wait_for_completion handling. The mac802154 layer
doesn't support asynchron transmit handling right now.
The state change behaviour is now changes, before it was:
1. assert while(!STATE_TRANSITION_IN_PROGRESS)
2. state change
3. assert while(!STATE_TRANSITION_IN_PROGRESS)
4. assert once(wanted state != current state)
Sometimes a unexcepted state change occurs when 4. assert was violated.
The new state change behaviour is:
1. assert while(!STATE_TRANSITION_IN_PROGRESS)
2. state change
3. wait state change timing according datasheet
4. assert once(wanted state != current state)
This behaviour is described in the at86rf231 software programming model [0].
The state change documentation in this programming guide should also valid for
at86rf212 and at86rf233 chips.
The transceiver don't do a FORCE_TX_ON while we want to transmit a PDU.
The new behaviour is a TX_ON and wait a receiving time (tFrame + tPAck).
If we are still in RX_AACK_BUSY then we transmit a FORCE_TX_ON as timeout
handling. The different is that FORCE_TX_ON aborts receiving and TX_ON
waits if RX_AACK_BUSY is finished. This should decrease the drop rate of
packets.
Alexander Aring [Wed, 2 Jul 2014 22:20:47 +0000 (00:20 +0200)]
at86rf230: add support for at86rf23x desense
To set the CCA_ED_THRES register the calculation for at86rf23x is
different than for at86rf212. This patch adds a new callback for this
calculation in chip data struct.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 2 Jul 2014 22:20:46 +0000 (00:20 +0200)]
at86rf230: remove is212 and add driver data
This patch adds a new at86rf2xx_chip_data structure which holds device
specific attributes. Instead of runtime decisions "if (is212())" we set
callbacks/attributes while device detection.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 2 Jul 2014 22:20:45 +0000 (00:20 +0200)]
at86rf230: rework detect device handling
This patch drops the current lowlevel spi calls for the detect device
function instead we handle this via regmap. Also put the detection of
in a seperate function and set all device specific attributes while detection.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 2 Jul 2014 22:20:43 +0000 (00:20 +0200)]
mac802154: at86rf230: add hw flags and merge ops
This patch adds new mac802154 hw flags for transmit power, csma and
listen before transmit (lbt). These flags indicates that the transceiver
supports these features. If the flags are set and the driver doesn't
implement the necessary functions, then ieee802154_register_device
returns -ENOSYS "Function not implemented".
This patch merges also all at86rf230 operations into one operations structure
and set the right hw flags for the at86rf230 transceivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 8 Jul 2014 04:22:58 +0000 (21:22 -0700)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-07-02
This series contains updates to i40e and i40evf.
Anjali fixes a possible race where we were trying to free the dummy packet
buffer in the function that created it, so cleanup the dummy packet buffer
in i40e_clean_tx_ring() instead. Also fixes an issue where the filter
program routine was not checking if there were descriptors available for
programming a filter.
Mitch fixes unnecessary delays when sending the admin queue commands by
moving a declaration up one level so we do not dereference it out of scope.
Fixes an issue with the VF where if the admin queue interrupts get lost for
some reason, the VF communication will stall as the VFs have no way of
reaching the PF. To alleviate this condition, go ahead and check the ARQ
every time we run the service task. Updates i40evf to allow the watchdog
to fire vector 0 via software, which makes the driver tolerant of dropped
interrupts on that vector.
Paul fixes a shifted '1' to be unsigned to avoid shifting a signed integer.
Jesse disables TPH by default since it is currently not enabled in the
current hardware. Also finishes the i40e implementation of get_settings
for ethtool.
Catherine adds a new variable (hw.phy.link_info.an_enabled) to track whether
auto-negotiation is enabled, along with the functionality to update the
variable. Adds the functionality to set the requested flow control mode.
Adds i40e implementation of setpauseparam and set_settings to ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the first batch of patches for the Freescale FEC ethernet driver.
They require the previously applied "net: fec: Don't clear IPV6 header
checksum field when IP accelerator enable" patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:23:30 +0000 (00:23 +0100)]
net: fec: fix missing kmalloc() failure check in fec_enet_alloc_buffers()
fec_enet_alloc_buffers() assumes that kmalloc() will never fail, which
is an invalid assumption. Fix this by implementing a common error
cleanup path, and use it to also clean up after failed bounce buffer
allocation.
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:23:25 +0000 (00:23 +0100)]
net: fec: ensure fec_enet_free_buffers() properly cleans the rings
Ensure that we do not double-free any allocations, and that any transmit
skbuffs are properly freed when we clean up the rings.
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:23:19 +0000 (00:23 +0100)]
net: fec: clean up transmit descriptor setup
Avoid writing any state until we're certain we can proceed with the
transmission: this avoids writing mapping error address values to the
descriptors, or setting the skbuff pointer until we have successfully
mapped the skb.
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:23:14 +0000 (00:23 +0100)]
net: fec: make rx skb handling more robust
Allocate, and then map the receive skb before writing any data to the
ring descriptor or storing the skb. When freeing the receive ring
entries, unmap and free the skb, and then clear the stored skb pointer.
This means we have ring data and skb pointer in one of two states:
either both fully setup, or nothing setup.
This simplifies the cleanup, as we can use just the skb pointer to
indicate whether the descriptor is setup, and thus avoids potentially
calling dma_unmap_single() on a DMA error value.
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:23:09 +0000 (00:23 +0100)]
net: fec: remove useless fep->opened
napi_disable() waits until the NAPI processing has completed, and then
prevents any further polls. At this point, the driver then clears
fep->opened. The NAPI poll function uses this to stop processing in
the receive path. Hence, it will never see this variable cleared,
because the NAPI poll has to complete before it will be cleared.
Therefore, this variable serves no purpose, so let's remove it.
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:23:04 +0000 (00:23 +0100)]
net: fec: stop the phy before shutting down the MAC
When the network interface goes down, stop the phy to prevent further
link up status changes before taking the MAC or netif sections down.
This prevents further reception of link up events which could
potentially call fec_restart().
Since phy_stop() takes the mutex which adjust_link() runs under, we
also ensure that adjust_link() will not already be processing a link
up event.
We also need to do this when suspending as well - we don't want a
mis-timed phy state change to restart the MAC after we have stopped
it for suspend, and thus need to restart the phy when resuming.
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:22:59 +0000 (00:22 +0100)]
net: fec: ensure that a disconnected phy isn't configured
When we disconnect from a phy, we should forget our pointer to it so we
don't accidentally try to configure it. We handle a NULL phy pointer
correctly in most places, except fec_enet_set_pauseparam(). Fix this
too.
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:22:54 +0000 (00:22 +0100)]
net: fec: remove checking for NULL phy_dev in fec_enet_close()
fep->phy_dev can not be NULL here for two reasons:
- fec_enet_open() will have successfully connected the phy, or will have
failed.
- fec_enet_open() will have called phy_start(fep->phy_dev), which
unconditionally dereferences this pointer.
If it were to be NULL here, then fec_enet_open() will have already
oopsed.
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:22:49 +0000 (00:22 +0100)]
net: fec: use netif_tx_disable() rather than netif_stop_queue()
We use netif_stop_queue() in several places where we want to ensure that
the start_xmit function is not running. netif_stop_queue() is not
sufficient to achieve that - it merely sets a flag to indicate that the
transmit queue(s) should not be run.
netif_tx_disable() gives this guarantee, since it takes the transmit
queue lock while marking the queue stopped. This will wait for the
transmit function to complete before returning.
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:22:44 +0000 (00:22 +0100)]
net: fec: fix interrupt handling races
While running: while :; do iperf -c <HOST> -P 4; done, transmit timeouts
are regularly reported. With the tx ring dumping in place, we can see
that all entries are in use, and the hardware has finished transmitting
these packets. However, the driver has not reclaimed these ring
entries.
This can occur if the interrupt handler is invoked at the wrong moment -
eg:
The result is that we clear the transmit interrupt, but we don't trigger
any cleaning of the transmit ring. Instead, use a different strategy:
- When receiving a transmit or receive interrupt, disable both tx and rx
interrupts, but do not acknowledge them. Schedule a napi poll. Don't
loop.
- When we are polled, read IEVENT, acknowledging the pending transmit
and receive interrupts, before then going on to process the
appropriate rings.
This allows us to avoid the race, and has a number of other advantages:
- we cut down on the number of transmit interrupts we have to process.
- we only look at the rings which have pending events.
- we gain additional throughput: the iperf total bandwidth increases
from about 180Mbps to 240Mbps:
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:22:39 +0000 (00:22 +0100)]
net: fec: fix ethtool set_pauseparam duplex bug
Setting the pause parameters causes a running network interface to be
restarted. However, the restart forces the FEC into half-duplex mode,
whether or not the remote end is in half-duplex mode. Misconfigured
duplex mode is a known source of problems on a link.
Fix this by always preserving the duplex mode on configuration changes.
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Mon, 7 Jul 2014 23:22:34 +0000 (00:22 +0100)]
net: fec: iMX6 FEC does not support half-duplex gigabit
The iMX6 gigabit FEC does not support half-duplex gigabit operation.
Phys attacked to the FEC may support this, and we currently do nothing
to disable this feature. This may result in an invalid configuration.
Mask out phy support for gigabit half-duplex operation.
Acked-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 8 Jul 2014 04:14:29 +0000 (21:14 -0700)]
Merge branch 'net-hash-tx'
Tom Herbert says:
====================
net: Improvements and applications of packet flow hash in transmit path
This patch series includes some patches which improve and make use
of skb->hash in the transmit path.
What is included:
- Infrastructure to save a precomputed hash in the sock structure.
For connected TCP and UDP sockets we only need to compute the
flow hash once and not once for every packet.
- Call skb_get_hash in get_xps_queue and __skb_tx_hash. This eliminates
the awkward access to skb->sk->sk_hash in the lower transmit path.
- Move UDP source port generation into a common function in udp.h This
implementation is mostly based on vxlan_src_port.
- Use non-zero IPv6 flow labels in flow_dissector as port information
for flow hash calculation.
- Implement automatic flow label generation on transmit (per RFC 6438).
- Don't repeatedly try to compute an L4 hash in skb_get_hash if we've
already tried to find one in software stack calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Wed, 2 Jul 2014 04:33:17 +0000 (21:33 -0700)]
net: Only do flow_dissector hash computation once per packet
Add sw_hash flag to skbuff to indicate that skb->hash was computed
from flow_dissector. This flag is checked in skb_get_hash to avoid
repeatedly trying to compute the hash (ie. in the case that no L4 hash
can be computed).
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Wed, 2 Jul 2014 04:33:10 +0000 (21:33 -0700)]
ipv6: Implement automatic flow label generation on transmit
Automatically generate flow labels for IPv6 packets on transmit.
The flow label is computed based on skb_get_hash. The flow label will
only automatically be set when it is zero otherwise (i.e. flow label
manager hasn't set one). This supports the transmit side functionality
of RFC 6438.
Added an IPv6 sysctl auto_flowlabels to enable/disable this behavior
system wide, and added IPV6_AUTOFLOWLABEL socket option to enable this
functionality per socket.
By default, auto flowlabels are disabled to avoid possible conflicts
with flow label manager, however if this feature proves useful we
may want to enable it by default.
It should also be noted that FreeBSD has already implemented automatic
flow labels (including the sysctl and socket option). In FreeBSD,
automatic flow labels default to enabled.
Performance impact:
Running super_netperf with 200 flows for TCP_RR and UDP_RR for
IPv6. Note that in UDP case, __skb_get_hash will be called for
every packet with explains slight regression. In the TCP case
the hash is saved in the socket so there is no regression.
Automatic flow labels disabled:
TCP_RR:
86.53% CPU utilization
127/195/322 90/95/99% latencies
1.40498e+06 tps
UDP_RR:
90.70% CPU utilization
118/168/243 90/95/99% latencies
1.50309e+06 tps
Automatic flow labels enabled:
TCP_RR:
85.90% CPU utilization
128/199/337 90/95/99% latencies
1.40051e+06
UDP_RR
92.61% CPU utilization
115/164/236 90/95/99% latencies
1.4687e+06
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Wed, 2 Jul 2014 04:33:01 +0000 (21:33 -0700)]
flow_dissector: Use IPv6 flow label in flow_dissector
This patch implements the receive side to support RFC 6438 which is to
use the flow label as an ECMP hash. If an IPv6 flow label is set
in a packet we can use this as input for computing an L4-hash. There
should be no need to parse any transport headers in this case.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Wed, 2 Jul 2014 04:32:49 +0000 (21:32 -0700)]
vxlan: Call udp_flow_src_port
In vxlan and OVS vport-vxlan call common function to get source port
for a UDP tunnel. Removed vxlan_src_port since the functionality is
now in udp_flow_src_port.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Wed, 2 Jul 2014 04:32:39 +0000 (21:32 -0700)]
udp: Add function to make source port for UDP tunnels
This patch adds udp_flow_src_port function which is intended to be
a common function that UDP tunnel implementations call to set the source
port. The source port is chosen so that a hash over the outer headers
(IP addresses and UDP ports) acts as suitable hash for the flow of the
encapsulated packet. In this manner, UDP encapsulation works with RSS
and ECMP based wrt the inner flow.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Wed, 2 Jul 2014 04:32:17 +0000 (21:32 -0700)]
net: Save TX flow hash in sock and set in skbuf on xmit
For a connected socket we can precompute the flow hash for setting
in skb->hash on output. This is a performance advantage over
calculating the skb->hash for every packet on the connection. The
computation is done using the common hash algorithm to be consistent
with computations done for packets of the connection in other states
where thers is no socket (e.g. time-wait, syn-recv, syn-cookies).
This patch adds sk_txhash to the sock structure. inet_set_txhash and
ip6_set_txhash functions are added which are called from points in
TCP and UDP where socket moves to established state.
skb_set_hash_from_sk is a function which sets skb->hash from the
sock txhash value. This is called in UDP and TCP transmit path when
transmitting within the context of a socket.
Tested: ran super_netperf with 200 TCP_RR streams over a vxlan
interface (in this case skb_get_hash called on every TX packet to
create a UDP source port).
Before fix:
95.02% CPU utilization
154/256/505 90/95/99% latencies
1.13042e+06 tps
Time in functions:
0.28% skb_flow_dissect
0.21% __skb_get_hash
After fix:
94.95% CPU utilization
156/254/485 90/95/99% latencies
1.15447e+06
Neither __skb_get_hash nor skb_flow_dissect appear in perf
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Wed, 2 Jul 2014 04:32:05 +0000 (21:32 -0700)]
flow_dissector: Abstract out hash computation
Move the hash computation located in __skb_get_hash to be a separate
function which takes flow_keys as input. This will allow flow hash
computation in other contexts where we only have addresses and ports.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Wake-on-LAN using Magic Packet with or without SecureOn
password is implemented doing the following:
- setting the password to the relevant UniMAC registers
- flagging the device as a wakeup source for the system, as well as
its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- enabling the MPD interrupt to wake us
The Device Tree binding documentation is also reflected to specify the
third optional Wake-on-LAN interrupt line.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This boolean tells us whether we are using the RXCHK hardware block,
so use a variable name that reflects that. RXCHK might be used in the
future to implement Wake-on-LAN using ARP or unicast packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the hardware recommended suspend/resume procedure for
SYSTEMPORT. We leverage the previous factoring work such that we can
logically break all suspend/resume operations into disctint RX and TX
code paths.
When the system enters S3, we will loose all register contents, so
make sure that we correctly re-program all the hardware and software
views of the RX & TX rings as well.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Factor common code that either enables or disables the network
interface with the networking stack. We are going to reuse these
functions for suspend/resume callbacks.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the coding style issues reported by checkpatch.pl
following issues fixed:
CHECK: Alignment should match open parenthesis
WARNING: line over 80 characters
CHECK: Blank lines aren't necessary before a close brace '}'
WARNING: networking block comments don't use an empty /* line, use /* Comment...
WARNING: Missing a blank line after declarations
WARNING: networking block comments start with * on subsequent lines
CHECK: braces {} should be used on all arms of this statement
Signed-off-by: Varka Bhadram <varkab@cdac.in> Tested-by: Alexander Aring <alex.aring@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Tue, 1 Jul 2014 08:22:41 +0000 (10:22 +0200)]
tipc: fix link acknowledge logic in receive path
Link state acks triggered from the receive path is done before
the last received packet have been processed by the link layer.
The effect of this is that the last received packet will not be
included in the ack. This causes problems if the link window is
set to TIPC_MIN_LINK_WIN, where the ack interval will be equal to
the link tolerance, and the link enters a stop-and-go behavior.
We move the ack logic to after link state processing, just before
the packet is delivered to higher layers.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: Carl Sigurjonsson <carl.sigurjonsson@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne [Tue, 1 Jul 2014 08:22:40 +0000 (10:22 +0200)]
tipc: refactor message delivery out of tipc_rcv
This is a cosmetic change, separating message delivery from the
link state processing.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Reviewed-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neal Cardwell [Mon, 30 Jun 2014 19:09:49 +0000 (15:09 -0400)]
tcp: switch snt_synack back to measuring transmit time of first SYNACK
Always store in snt_synack the time at which the server received the
first client SYN and attempted to send the first SYNACK.
Recent commit aa27fc501 ("tcp: tcp_v[46]_conn_request: fix snt_synack
initialization") resolved an inconsistency between IPv4 and IPv6 in
the initialization of snt_synack. This commit brings back the idea
from 843f4a55e (tcp: use tcp_v4_send_synack on first SYN-ACK), which
was going for the original behavior of snt_synack from the commit
where it was added in 9ad7c049f0f79 ("tcp: RFC2988bis + taking RTT
sample from 3WHS for the passive open side") in v3.1.
In addition to being simpler (and probably a tiny bit faster),
unconditionally storing the time of the first SYNACK attempt has been
useful because it allows calculating a performance metric quantifying
how long it took to establish a passive TCP connection.
Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Yuchung Cheng <ycheng@google.com> Cc: Octavian Purdila <octavian.purdila@intel.com> Cc: Jerry Chu <hkchu@google.com> Acked-by: Octavian Purdila <octavian.purdila@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Mon, 30 Jun 2014 16:38:37 +0000 (18:38 +0200)]
tlan: Isolate external PHY when using internal PHY
When using internal 10 Mbps PHY, isolate the external PHY from MII bus.
External PHY must be kept powered up because it passes TX from tlan chip to
network.
This fixes weird link-loss problems under load with OC-2326 card at 10 Mbps.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Mon, 30 Jun 2014 16:38:36 +0000 (18:38 +0200)]
tlan: Enable device at resume
pci_disable_device() is called in _suspend but there's no corresponding
pci_enable_device() in _resume.
This causes "disabling already-disabled device" warning on 2nd suspend.
Add pci_enable_device() call to _resume to fix this problem.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Mon, 30 Jun 2014 16:38:35 +0000 (18:38 +0200)]
tlan: Don't disable internal PHY on cards that use it in 10 Mbps mode
In tlan_reset_adapter, we disable internal PHY when an external one is used.
On cards which use internal PHY in 10 Mbps mode, we enable it later when
setting 10 Mbps mode but it does not really work (PHY fails to reset).
Leave it enabled instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ondrej Zary [Mon, 30 Jun 2014 16:38:33 +0000 (18:38 +0200)]
tlan: Make autonegotiation faster
Reduce the autonegotiation poll interval from 8 seconds to 2.
This greatly reduces the time needed to detect link presence,
especially on Olicom cards at 10 Mbps (two autonegoatiations required).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log