Chris Wilson [Thu, 28 Apr 2016 08:56:46 +0000 (09:56 +0100)]
drm/i915: Unify intel_ring_begin()
Combine the near identical implementations of intel_logical_ring_begin()
and intel_ring_begin() - the only difference is that the logical wait
has to check for a matching ring (which is assumed by legacy).
In the process some debug messages are culled as there were following a
WARN if we hit an actual error.
Ville Syrjälä [Fri, 13 May 2016 17:10:42 +0000 (10:10 -0700)]
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
When we resume the watermark register may contain some BIOS leftovers,
or just the hardware reset values. We should ignore those as the
pipes will be off anyway, and so frobbing around with intermediate
watermarks doesn't make much sense.
In fact I think we should just throw the skip_intermediate_wm flag
out, and instead properly sanitize the "active" watermarks to match
the current plane and pipe states. The actual wm state readout might
also need a bit of work. But for now, let's continue with the
skip_intermediate_wm to keep the fix more minimal.
Fixes this sort of errors on resume
[drm:ilk_validate_pipe_wm] LP0 watermark invalid
[drm:intel_crtc_atomic_check] No valid intermediate pipe watermarks are possible
[drm:intel_display_resume [i915]] *ERROR* Restoring old state failed with -22
and a boatload of subsequent modeset BAT fails on my ILK.
v2:
- Rebase; the SKL atomic WM patches that just landed changed the WM
structure fields in intel_crtc_state slightly. (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Fixes: ed4a6a7ca853 ("drm/i915: Add two-stage ILK-style watermark programming (v11)") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1463159442-20478-1-git-send-email-matthew.d.roper@intel.com
(cherry picked from commit e3d5457c7caabb77b3f1d0b09c4a63362e9b04d2)
[Jani: rebase on drm-next while cherry-picking] Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Daniel Vetter [Wed, 18 May 2016 16:47:11 +0000 (18:47 +0200)]
drm/i915/psr: Try to program link training times correctly
The default of 0 is 500us of link training, but that's not enough for
some platforms. Decoding this correctly means we're using 2.5ms of
link training on these platforms, which fixes flickering issues
associated with enabling PSR.
v2: Unbotch the math a bit.
v3: Drop debug hunk.
v4: Improve commit message.
Tested-by: Lyude <cpaul@redhat.com> Cc: Lyude <cpaul@redhat.com> Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95176 Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Sonika Jindal <sonika.jindal@intel.com> Cc: Durgadoss R <durgadoss.r@intel.com> Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com> Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: fritsch@kodi.tv Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-2-git-send-email-daniel.vetter@ffwll.ch
(cherry picked from commit 50db139018f9c94376d5f4db94a3bae65fdfac14) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ramalingam C [Tue, 19 Apr 2016 08:18:14 +0000 (13:48 +0530)]
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
In BXT DSI there is no regs programmed with few horizontal timings
in Pixels but txbyteclkhs.. So retrieval process adds some
ROUND_UP ERRORS in the process of PIXELS<==>txbyteclkhs.
Actually here for the given adjusted_mode, we are calculating the
value programmed to the port and then back to the horizontal timing
param in pixels. This is the expected value at the end of get_config,
including roundup errors. And if that is same as retrieved value
from port, then retrieved (HW state) adjusted_mode's horizontal
timings are corrected to match with SW state to nullify the errors.
Ville Syrjälä [Fri, 13 May 2016 14:55:17 +0000 (17:55 +0300)]
drm/i915: Don't leave old junk in ilk active watermarks on readout
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Chris Wilson [Fri, 29 Apr 2016 12:18:23 +0000 (13:18 +0100)]
drm/i915: Fix gen8 semaphores id for legacy mode
With the introduction of a distinct engine->id vs the hardware id, we need
to fix up the value we use for selecting the target engine when signaling
a semaphore. Note that these values can be merged with engine->guc_id.
Set the lane count for HDMI to 4. This will make it easier to
unduplicate CHV phy code.
This also fixes the the soft reset programming for HDMI with CHV. After
commit a8f327fb8464 ("drm/i915: Clean up CHV lane soft reset
programming"), it wouldn't set the right bits for PCS23 since it relied
on a lane count that was never set.
v2: Set lane_count in *_get_config() to please state checker. (0day)
v3: Set lane_count for DDI in DVI mode too. (CI)
v4: Add note about CHV soft lane reset. (Ander)
Chris Wilson [Wed, 27 Apr 2016 08:02:01 +0000 (09:02 +0100)]
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
Faced with sporadic machine hangs on gen7, that mimic the issue of
concurrent writes to the same cacheline and seem to start with
commit 9b9ed3093613 (drm/i915: Remove forcewake dance from seqno/irq
barrier on legacy gen6+), let us restore the spinlock around the mmio
read.
Ville Syrjälä [Fri, 6 May 2016 18:35:55 +0000 (21:35 +0300)]
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
Move the intel_enable_gtt() call to happen before we touch the GTT
during resume. Right now it's done way too late. Before
commit ebb7c78d358b ("agp/intel-gtt: Only register fake agp driver for gen1")
it was actually done earlier on account of also getting called from
the resume hook of the fake agp driver. With the fake agp driver
no longer getting registered we must move the call up.
The symptoms I've seen on my 830 machine include lowmem corruption,
other kinds of memory corruption, and straight up hung machine during
or just after resume. Not really sure what causes the memory corruption,
but so far I've not seen any with this fix.
I think we shouldn't really need to call this during init, but we have
been doing that so I've decided to keep the call. However moving that
call earlier could be prudent as well. Doing it right after the
intel-gtt probe seems appropriate.
Also tested this on 946gz,elk,ilk and all seemed quite happy with
this change.
v2: Reorder init_hw vs. enable_hw functions (Chris)
Ville Syrjälä [Wed, 4 May 2016 11:45:22 +0000 (14:45 +0300)]
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
DP dual mode type 1 DVI adaptors aren't required to implement any
registers, so it's a bit hard to detect them. The best way would
be to check the state of the CONFIG1 pin, but we have no way to
do that. So as a last resort, check the VBT to see if the HDMI
port is in fact a dual mode capable DP port.
v2: Deal with VBT code reorganization
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Reduce DEVICE_TYPE_DP_DUAL_MODE_BITS a bit
Accept both DP and HDMI dvo_port in VBT as my BSW
at least declare its DP port as HDMI :(
v3: Ignore DEVICE_TYPE_NOT_HDMI_OUTPUT (Shashank)
Cc: stable@vger.kernel.org Cc: Tore Anderson <tore@fud.no> Reported-by: Tore Anderson <tore@fud.no> Fixes: 7a0baa623446 ("Revert "drm/i915: Disable 12bpc hdmi for now"") Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1462362322-31278-1-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit d61992565bd3cc5b66d74ed2e96df043c2a207e2) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Mon, 2 May 2016 19:08:24 +0000 (22:08 +0300)]
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
To save a bit of power, let's try to turn off the TMDS output buffers
in DP++ adaptors when we're not driving the port.
v2: Let's not forget DDI, toss in a debug message while at it
v3: Just do the TMDS output control based on adaptor type. With the
helper getting passed the type, we wouldn't actually have to
check at all in the driver, but the check eliminates the debug
output more honest
Ville Syrjälä [Mon, 2 May 2016 19:08:23 +0000 (22:08 +0300)]
drm/i915: Respect DP++ adaptor TMDS clock limit
Try to detect the max TMDS clock limit for the DP++ adaptor (if any)
and take it into account when checking the port clock.
Note that as with the sink (HDMI vs. DVI) TMDS clock limit we'll ignore
the adaptor TMDS clock limit in the modeset path, in case users are
already "overclocking" their TMDS links. One subtle change here is that
we'll have to respect the adaptor TMDS clock limit when we decide whether
to do 12bpc or 8bpc, otherwise we might end up picking 12bpc and
accidentally driving the TMDS link out of spec even when the user chose
a mode that fits wihting the limits at 8bpc. This means you can't
"overclock" your DP++ dongle at 12bpc anymore, but you can continue to
do so at 8bpc.
Note that for simplicity we'll use the I2C access method for all dual
mode adaptors including type 2. Otherwise we'd have to start mixing
DP AUX and HDMI together. In the future we may need to do that if we
come across any board designs that don't hook up the DDC pins to the
DP++ connectors. Such boards would obviously only work with type 2
dual mode adaptors, and not type 1.
v2: Store adaptor type under indel_hdmi->dp_dual_mode
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Pass adaptor type to drm_dp_dual_mode_max_tmds_clock(),
and use it for type1 adaptors as well
Cc: stable@vger.kernel.org Reported-by: Tore Anderson <tore@fud.no> Fixes: 7a0baa623446 ("Revert "drm/i915: Disable 12bpc hdmi for now"") Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-3-git-send-email-ville.syrjala@linux.intel.com Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit b1ba124d8e95cca48d33502a4a76b1ed09d213ce) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Ville Syrjälä [Fri, 6 May 2016 13:46:52 +0000 (16:46 +0300)]
drm: Add helper for DP++ adaptors
Add a helper which aids in the identification of DP dual mode
(aka. DP++) adaptors. There are several types of adaptors
specified: type 1 DVI, type 1 HDMI, type 2 DVI, type 2 HDMI
Type 1 adaptors have a max TMDS clock limit of 165MHz, type 2 adaptors
may go as high as 300MHz and they provide a register informing the
source device what the actual limit is. Supposedly also type 1 adaptors
may optionally implement this register. This TMDS clock limit is the
main reason why we need to identify these adaptors.
Type 1 adaptors provide access to their internal registers and the sink
DDC bus through I2C. Type 2 adaptors provide this access both via I2C
and I2C-over-AUX. A type 2 source device may choose to implement either
of these methods. If a source device implements the I2C-over-AUX
method, then the driver will obviously need specific support for such
adaptors since the port is driven like an HDMI port, but DDC
communication happes over the AUX channel.
This helper should be enough to identify the adaptor type (some
type 1 DVI adaptors may be a slight exception) and the maximum TMDS
clock limit. Another feature that may be available is control over
the TMDS output buffers on the adaptor, possibly allowing for some
power saving when the TMDS link is down.
Other user controllable features that may be available in the adaptors
are downstream i2c bus speed control when using i2c-over-aux, and
some control over the CEC pin. I chose not to provide any helper
functions for those since I have no use for them in i915 at this time.
The rest of the registers in the adaptor are mostly just information,
eg. IEEE OUI, hardware and firmware revision, etc.
v2: Pass adaptor type to helper functions to ease driver implementation
Fix a bunch of typoes (Paulo)
Add DRM_DP_DUAL_MODE_UNKNOWN for the case where we don't (yet) know
the type (Paulo)
Reject 0x00 and 0xff DP_DUAL_MODE_MAX_TMDS_CLOCK values (Paulo)
Adjust drm_dp_dual_mode_detect() type2 vs. type1 detection to
ease future LSPCON enabling
Remove the unused DP_DUAL_MODE_LAST_RESERVED define
v3: Fix kernel doc function argument descriptions (Jani)
s/NONE/UNKNOWN/ in drm_dp_dual_mode_detect() docs
Add kernel doc for enum drm_dp_dual_mode_type
Actually build the docs
Fix more typoes
v4: Adjust code indentation of type2 adaptor detection (Shashank)
Add debug messages for failurs cases (Shashank)
v5: EXPORT_SYMBOL(drm_dp_dual_mode_read) (Paulo)
Cc: stable@vger.kernel.org Cc: Tore Anderson <tore@fud.no> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Shashank Sharma <shashank.sharma@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Shashank Sharma <shashank.sharma@intel.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> (v4) Link: http://patchwork.freedesktop.org/patch/msgid/1462542412-25533-1-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit ede53344dbfd1dd43bfd73eb6af743d37c56a7c3) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm/i915/bxt: Explicitly clear the Turbo control register
As a part of WaGsvDisableTurbo, Driver makes an early exit from the
Gen9 Turbo enabling function, so doesn't program the Turbo Control register.
But BIOS could leave the Hw Turbo as enabled, so need to explicitly clear
out the Control register just to avoid inconsitency with debugfs
interface, which will show Turbo as enabled only and that is not expected
after adding the WaGsvDisableTurbo. Apart from this there is no problem
even if the Turbo is left enabled in the Control register, as the Up/Down
interrupts would remain masked.
v2: Add explicit clearing of Turbo Control register to *_disable_rps()
also for the similar consistency (Chris)
drm/i915: Correct the i915_frequency_info debugfs output
There are certain registers, which captures the time elapsed in the
in current Up/Down EI, for how long GT has been Idle/Busy/Avg in the
current Up/Down EI and also in the previous Up/Down EI.
These register values are reported by the i915_frequency_info debugfs
interface. The Driver prints the 'us' suffix after the values, albeit
they are actually in raw form & not in microsecond units.
This patch removes the 'us' suffix so that its clear to User that values
are indeed in raw form.
v2: Present the values in microseconds unit also, after platform
specific conversion (Chris)
v3: Add a space between raw & microsecond value (Chris)
Ville Syrjälä [Wed, 20 Apr 2016 13:43:56 +0000 (16:43 +0300)]
drm/i915: Make RPS EI/thresholds multiple of 25 on SNB-BDW
Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().
I bisected the problem down to
commit 8a5864377b12 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.
These are the original EI/thresholds:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10250
GEN6_RP_UP_THRESHOLD 9225
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 8000
GEN6_RP_UP_THRESHOLD 6800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
These are after 8a5864377b12:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10156
GEN6_RP_UP_THRESHOLD 9140
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7812
GEN6_RP_UP_THRESHOLD 6640
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
And these are what we have after this patch:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10175
GEN6_RP_UP_THRESHOLD 9150
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7825
GEN6_RP_UP_THRESHOLD 6650
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
Cc: stable@vger.kernel.org Cc: Akash Goel <akash.goel@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B Fixes: 8a5864377b12 ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.com Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
This patch does the following:
- Fakes live status of HDMI as connected (even if that's not).
While testing certain (monitor + cable) combinations with
various intel platforms, it seems that live status register
doesn't work reliably on some older devices. So limit the
live_status check for HDMI detection, only for platforms
from gen7 onwards.
V2: restrict faking live_status to certain platforms
V3: (Ville)
- keep the debug message for !live_status case
- fix indentation of comment
- remove "warning" from the debug message
(Jani)
- Change format of fix details in the commit message
Imre Deak [Wed, 20 Apr 2016 17:46:06 +0000 (20:46 +0300)]
drm/i915/bxt: Force reprogramming a PHY with invalid HW state
It's possible that BIOS enables PHY0, but it programmes only the first
channel on it. Since we program the PHYs only during driver loading this
is an incorrect configuration from the driver's point of view, since we
may use both channels eventually. Detect this scenario and force
reprogramming the PHY in this case.
The actual scenario for me was that the lane optimization for the second
channel in PHY0 was not setup by BIOS and so a state verification
warning was triggered. Everything else was setup properly.
Imre Deak [Thu, 21 Apr 2016 16:19:21 +0000 (19:19 +0300)]
drm/i915/bxt: Wait for PHY1 GRC done if PHY0 was already enabled
If we skipped PHY0 initialization because it was already enabled by
BIOS, we still have to wait for the PHY1 GRC calibration as that is
done as part of the PHY0 init.
v2:
- Use the actual PHY index in the debug message in
broxton_phy_wait_grc_done() (Ville)
Imre Deak [Wed, 20 Apr 2016 17:46:04 +0000 (20:46 +0300)]
drm/i915/bxt: Use PHY0 GRC value for HW state verification
It's possible that BIOS enables PHY1 only to read out the GRC value from
it to be used in PHY0 and then disables PHY1. In this case we can't use
the PHY1 GRC value for state verification, so use instead the one in PHY0
always.
Imre Deak [Wed, 20 Apr 2016 17:27:57 +0000 (20:27 +0300)]
drm/i915/bxt: Enable DC5 during runtime resume
Right after runtime resume we know that we can re-enable DC5, since we
just disabled DC9 and power well 2 is disabled. So enable DC5 explicitly
instead of delaying this until the next time we disable power well 2.
Imre Deak [Wed, 20 Apr 2016 17:27:56 +0000 (20:27 +0300)]
drm/i915/bxt: Sanitize DC state tracking during system resume
After suspend-to-ram or -disk we don't know what power state the display
HW will be, DC0 or DC9 are both possible states, so reset the software
DC state tracking in these cases. This gets rid of 'DC state mismatch'
error messages during resuming from ram or disk where we expected to be
in DC9 (as set by the suspend handler) but we are in DC0.
v2:
- Remove extra WS in gen9_sanitize_dc_state() (Bob)
Imre Deak [Wed, 20 Apr 2016 17:27:55 +0000 (20:27 +0300)]
drm/i915/bxt: Don't uninit/init display core twice during system suspend/resume
Atm, we run the BSpec display core uninit/init sequences twice during
system suspend/resume. While this shouldn't cause any problem, it's
redundant, so get rid of the duplicate call.
Imre Deak [Wed, 20 Apr 2016 17:27:54 +0000 (20:27 +0300)]
drm/i915: Inline intel_suspend_complete
Initially we thought that the platform specific suspend/resume sequences
can be shared between the runtime and system suspend/resume handlers.
This turned out to be not true, we have quite a few differences on most
of the platforms. This was realized already earlier by Paulo who
inlined the platform specific resume_prepare handlers. We have the
same problem with the corresponding suspend_complete handlers, there are
platform differences that make it unfeasible to share the code between
the runtime and system suspend paths. Also now we call functions that
need to be paired like hsw_enable_pc8()/hsw_disable_pc8() from different
levels of the call stack, which is confusing. Fix this by inlining the
suspend_complete handlers too.
This is also needed by the next patch that removes a redundant
uninit/init call during system suspend/resume on BXT.
Imre Deak [Tue, 19 Apr 2016 10:00:36 +0000 (13:00 +0300)]
drm/i915/kbl: Don't WARN for expected secondary MISC IO power well request
In commit 5f304c873634 ("drm/i915/kbl: Reset secondary power well requests
left on by DMC/KVMR") I forgot about the fact that SKL==KBL most of the
time and that a secondary MISC IO power well request left on by the DMC is
"expected". Tune down the corresponding WARN to be a debug message. This
was caught by CI suspend tests.
Mika Kahola [Wed, 20 Apr 2016 12:39:02 +0000 (15:39 +0300)]
drm/i915: Fix eDP low vswing for Broadwell
It was noticed on bug #94087 that module parameter
i915.edp_vswing=2 that should override the VBT setting
to use default voltage swing (400 mV) was not applied
for Broadwell.
This patch provides a fix for this by checking if default
i.e. higher voltage swing is requested to be used and
applies the DDI translations table for DP instead of eDP
(low vswing) table.
v2: Combine two if statements into one (Jani)
v3: Change dev_priv->edp_low_vswing to use dev_priv->vbt.edp.low_vswing
Dave Gordon [Tue, 12 Apr 2016 13:46:16 +0000 (14:46 +0100)]
drm/i915: check for ERR_PTR from i915_gem_object_pin_map()
The newly-introduced function i915_gem_object_pin_map() returns an
ERR_PTR (not NULL) if the pin-and-map opertaion fails, so that's what we
must check for. And it's nicer not to assign such a pointer-or-error to
a structure being filled in until after it's been validated, so we
should keep it local and avoid exporting a bogus pointer. Also, for
clarity and symmetry, we should clear 'virtual_start' along with 'vma'
when unmapping a ringbuffer.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Alex Dai [Tue, 19 Apr 2016 15:08:35 +0000 (16:08 +0100)]
drm/i915/guc: drop cached copy of 'wq_head'
Now that we keep the GuC client process descriptor permanently mapped,
we don't really need to keep a local copy of the GuC's work-queue-head.
So we can simplify the code a little by not doing this.
Signed-off-by: Alex Dai <yu.dai@intel.com> Signed-off-by: Dave Gordon <david.s.gordon@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Dave Gordon [Tue, 19 Apr 2016 15:08:34 +0000 (16:08 +0100)]
drm/i915/guc: keep GuC doorbell & process descriptor mapped in kernel
Don't use kmap_atomic() for doorbell & process descriptor access.
This patch fixes the BUG shown below, where the thread could sleep
while holding a kmap_atomic mapping. In order not to need to call
kmap_atomic() in this code path, we now set up a permanent kernel
mapping of the shared doorbell and process-descriptor page, and
use that in all doorbell and process-descriptor related code.
Chris Wilson [Wed, 20 Apr 2016 11:09:52 +0000 (12:09 +0100)]
drm/i915/shrinker: Only shmemfs objects are backed by swap
Since we can only swap out shmemfs objects, those are the only ones that
can influence the ability of the shrinker to free pages. Currently, all
non-shmemfs objects have a raised pages_pin_count to protect them from
the shrinker, so this just makes the logic for can_release_pages()
clearer (and safer in future so that we don't over estimate our ability
to free up pages from future non-swappable objects).
Chris Wilson [Wed, 20 Apr 2016 11:09:51 +0000 (12:09 +0100)]
drm/i915/shrinker: Report "unevictable" pages
Inside the shrinker we call can_release_pages() to indicate whether or
not we can make forward progress in freeing up memory by unbinding that
object. When adding our report to oom, we should be using the same
logic.
Whilst here, change the reporting from bytes to pages so that it looks
smaller to the user!, is consistent with the neighbouring oom report
itself which displays counts in pages, and makes the unsigned long
overflow less likely.
Chris Wilson [Wed, 20 Apr 2016 11:09:50 +0000 (12:09 +0100)]
drm/i915/shrinker: Only report objects with extra pinned pages as pinned
When iterating over the bound list, we expect all objects there to have
their pages pinned (by the bound VMA). So only report those objects with
additional pin count on their pages as "pinned". These should be those
objects used for display and hardware access.
drm/i915/gen8+: Do not enable DPF interrupt since the handler does not exist
Looks like DPF was not implemented for gen8+ but the IER and IMR
are still enabled on initialization.
Since there is no code to handle this interrupt, gate the irq
enablement behind HAS_L3_DPF in case the feature gets enabled
in the future.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
drm/i915: Fixing eDP detection on certain platforms
Since commit 30d9aa4265fe ("drm/i915: Read sink_count dpcd always"),
the status of a DP connector depends on its sink count value.
However, some eDP panels don't set that value appropriately,
causing them to be reported as disconnected.
Fix this by ignoring sink count for eDP.
v2: Rephrased commit message. (Ander)
In case of eDP, returning status as connected if DPCD
read succeeds to avoid any further operations.
Fixes: 30d9aa4265fe ("drm/i915: Read sink_count dpcd always") Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reported-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com> Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com> Tested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1460444034-22320-1-git-send-email-shubhangi.shrivastava@intel.com
drm/i915/dp/mst: Fix MST logic in intel_dp_long_pulse()
In commit 7d23e3c37bb3 ("drm/i915: Cleaning up intel_dp_hpd_pulse") some
much needed clean-up was done, but unfortunately part of the change
broke DP MST. The real issue was setting the connector state to
disconnected in the MST case, which is good, but the code then (after
a goto) checks if the connector state is not connected and shuts down
MST if this is the case, which is bad. With this change both SST and
MST seem to be happy.
v2: Add removed check further up in the function to be sure that MST
is shut down when we lose the link. (Ander)
Fixes: commit 7d23e3c37bb3 ("drm/i915: Cleaning up intel_dp_hpd_pulse")
cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
cc: Nathan D Ciobanu <nathan.d.ciobanu@intel.com> Signed-off-by: Jim Bride <jim.bride@linux.intel.com> Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com> Reviewed-by: Lyude <cpaul@redhat.com> Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1460394684-7036-1-git-send-email-jim.bride@linux.intel.com
Do not use magic numbers, do not prefix stuff with "PCI_", do not
declare registers in implementation files. Also move the PCI
registers under correct comment in i915_reg.h.
v2:
- Consistently use BSM (not BDSM or other variants from PRM) (Chris)
- Also include register address to help identify the register (Chris)
v3:
- Refer to register value as *_val instead of *_reg (Chris)
v4:
- Make style checker happy
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Ville Syrjälä [Mon, 18 Apr 2016 11:02:28 +0000 (14:02 +0300)]
drm/i915: Define HSW/BDW display power domains the right way up
Currently we're trying to define HSW/BDW power wells by what's not
included. Let's do it the other way around, so that you can actually
tell when the power well would get enabled. This will also allow us to
add new power domains without accidentally adding it to the HSW/BDW
display power domains.
The current set of domains looks rather buggy even:
- POWER_DOMAIN_MODESET is included in the display power well needlessly
- DDI-B to DDI-E were not part of the display power well when they
should be
Ville Syrjälä [Mon, 18 Apr 2016 11:02:27 +0000 (14:02 +0300)]
drm/i915: Define VLV/CHV display power well domains properly
Currently we're using POWER_DOMAIN_MASK as the power domains for the
display power well on VLV/CHV. That includes all power domains even
though the disp2d/pipe-a power well is not needed for a lot of things.
Let's reduce these to what we actually need.
Ville Syrjälä [Mon, 18 Apr 2016 11:02:26 +0000 (14:02 +0300)]
drm/i915: Set .domains=POWER_DOMAIN_MASK for the always-on well
The always-on well is the same as runtime PM, so we should just
"enable" it for any power domain. Throw out the usless
FOO_ALWAYS_ON_DOMAINS defines and just use POWER_DOMAIN_MASK.
Ville Syrjälä [Mon, 18 Apr 2016 17:34:04 +0000 (20:34 +0300)]
drm/i915: Fix oops in vlv_force_pll_on()
intel_pipe_will_have_type() doesn't just look at the passied in
pipe_config, instead it expects there to be a full atomic state behind
it. Obviously that won't go so well when vlv_force_pll_on() just uses a
temp pipe_config. Fix things by using pipe_config->has_dsi_encoder
instead intel_pipe_will_have_type(INTEL_OUTPUT_DSI) to check if we need
to actually enable the DPLL.
The regressing patch wasn't exactly new (as in first posted more than
six months ago), so I'm a bit baffled how I didn't manage to hit this
myself so far.
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Marius Vlad <marius.c.vlad@intel.com> Reported-by: Marius Vlad <marius.c.vlad@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94995 Fixes: cd2d34d9b61f ("drm/i915: Setup DPLL/DPLLMD for DSI too on VLV/CHV") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1461000844-20543-1-git-send-email-ville.syrjala@linux.intel.com Tested-by: Marius Vlad <marius.c.vlad@intel.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Imre Deak [Mon, 18 Apr 2016 11:48:21 +0000 (14:48 +0300)]
drm/i915/gen9: Fix runtime PM refcounting in case DMC firmware isn't loaded
While we disable runtime PM and with that display power well support if
the DMC firmware isn't loaded, we still want to disable power wells
during system suspend and driver unload. So drop/reacquire the
corresponding power refcount during suspend/resume and driver unloading.
This also means we have to check if DMC is not loaded and skip enabling
DC states in the power well code.
v2:
- Reuse intel_csr_ucode_suspend() in intel_csr_ucode_fini() instead of
opencoding the former. (Chris)
- Add docbook comment to the public resume and suspend functions.
Imre Deak [Mon, 18 Apr 2016 07:04:21 +0000 (10:04 +0300)]
drm/i915/ddi: Fix eDP VDD handling during booting and suspend/resume
The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:
commit 6d93c0c41760c0 ("drm/i915: fix VDD state tracking after system
resume")
At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).
While at it remove an unnecessary function call indirection.
This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.
Imre Deak [Mon, 18 Apr 2016 11:45:54 +0000 (14:45 +0300)]
drm/i915: Fix system resume if PCI device remained enabled
During system resume we depended on pci_enable_device() also putting the
device into PCI D0 state. This won't work if the PCI device was already
enabled but still in D3 state. This is because pci_enable_device() is
refcounted and will not change the HW state if called with a non-zero
refcount. Leaving the device in D3 will make all subsequent device
accesses fail.
This didn't cause a problem most of the time, since we resumed with an
enable refcount of 0. But it fails at least after module reload because
after that we also happen to leak a PCI device enable reference: During
probing we call drm_get_pci_dev() which will enable the PCI device, but
during device removal drm_put_dev() won't disable it. This is a bug of
its own in DRM core, but without much harm as it only leaves the PCI
device enabled. Fixing it is also a bit more involved, due to DRM
mid-layering and because it affects non-i915 drivers too. The fix in
this patch is valid regardless of the problem in DRM core.
v2:
- Add a code comment about the relation of this fix to the freeze/thaw
vs. the suspend/resume phases. (Ville)
- Add a code comment about the inconsistent ordering of set power state
and device enable calls. (Chris)
Imre Deak [Fri, 15 Apr 2016 19:32:58 +0000 (22:32 +0300)]
drm/i915/kbl: Reset secondary power well requests left on by DMC/KVMR
The workaround added in
commit c6782b76d31a ("drm/i915/gen9: Reset secondary power well
requests left on by DMC/KVMR")
needs to be applied on Kabylake too as shown by the corresponding
timeout errors about power well 1 and MISC IO power well disabling in
the latest CI run.
Ville Syrjälä [Mon, 18 Apr 2016 11:29:32 +0000 (14:29 +0300)]
drm/i915: Replace nondescript 'WARN_ON(!lret)' with a sensible error message
When a vblank wait times out in intel_atomic_wait_for_vblanks() we just
get a cryptic 'WARN_ON(!ret)' backtrace in dmesg. Repace it with
something that tells you what actually happened.
Chris Wilson [Sun, 17 Apr 2016 19:42:46 +0000 (20:42 +0100)]
drm/i915: Avoid stalling on pending flips for legacy cursor updates
The legacy cursor ioctl expects to be asynchronous with respect to other
screen updates, in particular page flips. As X updates the cursor from a
signal context, if the cursor blocks then it will stall both the input
and output chains causing bad stuttering and horrible UX.
Reported-and-tested-by: Rafael Ristovski <rafael.ristovski@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94980 Fixes: 5008e874edd34 ("drm/i915: Make wait_for_flips interruptible.") Suggested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jani Nikula <jani.nikula@intel.com> Cc: stable@vger.kernel.org Link: http://patchwork.freedesktop.org/patch/msgid/1460922166-20292-1-git-send-email-chris@chris-wilson.co.uk Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Jani Nikula [Fri, 15 Apr 2016 12:47:31 +0000 (15:47 +0300)]
drm/i915/dsi: fix CHV dsi encoder hardware state readout on port C
Due to "some hardware limitation" the DPI enable bit in port C control
register does not get set on VLV. As a workaround we check the status in
pipe B conf register instead. The workaround was added in
drm/i915: Software workaround for getting the HW status of DSI Port C on BYT
Empirical evidence (on Surface 3 with DSI on port C per VBT) shows that
this is the case also on CHV, so extend the workaround to CHV. We still
have the device ready register check in place, so this should not get
confused with e.g. HDMI on pipe B.
This fixes a number of state checker warnings on CHV DSI port C.
Reflect the status of obj->mapping as added with the
i915_gem_object_pin_map API.
'M' was chosen to designate the pin mapped status.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Ville Syrjälä [Tue, 12 Apr 2016 19:14:38 +0000 (22:14 +0300)]
drm/i915: Reject 'Center' scaling mode for eDP/DSI on GMCH platforms
We don't have a LVDS_BORDER_ENABLE type of bit for either eDP or DSI,
and just trying to frob the display timings to include borders results
in a corrupted picture. So reject the 'Center' scaling mode on GMCH
platforms for eDP and DSI.
TODO: Should really filter out the unsupported modes from the prop,
but that would be fairly invasive since the prop is now created and
stored by drm core. So leave it for a rainy day.
Ville Syrjälä [Tue, 12 Apr 2016 19:14:35 +0000 (22:14 +0300)]
drm/i915: Compute DSI PLL parameters during .compute_config()
Compute the DSI PLL parameters during .compute_config() rather than
.pre_pll_enable() so that we can fail gracefully if we can't find
suitable parameters.
In order to do that we need to store the DSI PLL parameters in
pipe_config.
Ville Syrjälä [Tue, 12 Apr 2016 19:14:34 +0000 (22:14 +0300)]
drm/i915: Setup DPLL/DPLLMD for DSI too on VLV/CHV
Set up DPLL and DPLL_MD even when driving DSI output on VLV/CHV. While
the DPLL isn't used to provide the clock we still need the refclock, and
it appears that the pixel repeat factor also has an effect on DSI
output. So set up eveyrhing in DPLL and DPLL_MD as we would do for
DP/HDMI/VGA, but don't actually enable the DPLL or configure the
dividers via DPIO.
drm/i915/bxt: Reversed polarity of PORT_PLL_REF_SEL bit
This reversed bit polarity is actually common
for all BXT and APL SoCs. Therefore, revision checking
in the original commit should be removed to make
the bit set regardless of revision ID of GFX block.
Imre Deak [Mon, 4 Apr 2016 14:27:10 +0000 (17:27 +0300)]
drm/i915/bxt: Add HW state verification for DDI PHY and CDCLK
I caught a few errors in our current PHY/CDCLK programming by sanity
checking the actual programmed state, so I thought it would be also
useful for the future. In addition to verifying the state after
programming it also verify it after exiting DC5, to make sure DMC
restored/kept intact everything related.
v2:
- Inlining __phy_reg_verify_state() doesn't make sense and also
incorrect, so don't do it (PW/CI gcc)
v3:
- Rebase on latest -nightly
Imre Deak [Fri, 1 Apr 2016 13:02:44 +0000 (16:02 +0300)]
drm/i915/bxt: Don't reprogram an already enabled DDI PHY
If BIOS has already programmed and enabled a PHY, don't reprogram it as
that may interfere with the currently active outputs. A follow-up patch
will add state verification, so we can catch any misconfiguration on
BIOS's behalf.
Imre Deak [Fri, 1 Apr 2016 13:02:43 +0000 (16:02 +0300)]
drm/i915/bxt: Sanitize the DBUF HW state together with CDCLK
When determining whether CDCLK is enabled by BIOS and so we should skip
reprogramming it, we didn't check the related DBUF power request and
state. In theory BIOS could enable one without the other so check for
this case and reprogram things if something is amiss.
Imre Deak [Fri, 1 Apr 2016 13:02:42 +0000 (16:02 +0300)]
drm/i915/bxt: Don't toggle power well 1 on-demand
Power well 1 is managed by the DMC firmware so don't toggle it on-demand
from the driver. This means we need to follow the BSpec display
initialization sequence during driver loading and resuming (both system
and runtime) and enable power well 1 only once there. Afterwards DMC
will toggle power well 1 whenever entering/exiting DC5.
For this to work we also need to do away getting the PLL power domain,
since that just kept runtime PM disabled for good.
Imre Deak [Fri, 1 Apr 2016 13:02:41 +0000 (16:02 +0300)]
drm/i915/bxt: Power down DDI PHYs separately during the per PHY uninit
The power-down step logically belongs to the individual PHY uninit
sequence so move it there. The only functional change is that we will
power down now PHY 1 separately before PHY 0 and preserve the other bits
in the register which are defined as reserved.
Imre Deak [Mon, 4 Apr 2016 12:42:57 +0000 (15:42 +0300)]
drm/i915/skl: Unexport skl_pw1_misc_io_init
On Broxton we need to enable/disable power well 1 during the init/unit
display sequence similarly to Skylake/Kabylake. The code for this will
be added in a follow-up patch, but to prepare for that unexport
skl_pw1_misc_io_init(). It's a simple function called only from a single
place and having it inlined in the Skylake display core init/unit
functions will make it easier to compare it with its Broxton
counterpart.
This also flips the order of Misc IO and power well 1 disabling which
matches the enabling order. The specification doesn't prescribe the
disabling order, so this should be fine.
v2:
- Fix incorrect enable vs. disable power well call in
skl_display_core_uninit() (Patrik)
- Add commit comment about chaning the order of PW1 and Misc IO power
well disabling (Patrik)
Imre Deak [Fri, 1 Apr 2016 13:02:38 +0000 (16:02 +0300)]
drm/i915/bxt: Suspend power domains during suspend-to-idle
On SKL/KBL suspend-to-idle (aka freeze/s0ix) is performed with DMC
firmware assistance where the target display power state is DC6. On
Broxton on the other hand we don't use the firmware for this, but rely
instead on a manual DC9 flow. For this we have to uninitialize the
display following the BSpec display uninit sequence, just as during
S3/S4, so make sure we follow this sequence.
Imre Deak [Fri, 1 Apr 2016 13:02:37 +0000 (16:02 +0300)]
drm/i915/gen9: Fix DMC/DC state asserts
The display power well support and DC state management doesn't depend on
runtime PM support, so remove the incorrect asserts about this.
Also Broxton does support DC5, so the related assert in
assert_can_enable_dc5() is incorrect. There is a more generic and
correct assert for this already in gen9_set_dc_state(), so we can remove
all the other ones.
At the same time convert WARNs to WARN_ONCE for consistency with the
other DC state asserts.
Imre Deak [Fri, 1 Apr 2016 13:02:36 +0000 (16:02 +0300)]
drm/i915/gen9: Make power well disabling synchronous
So far we only power well enabling was synchronous not disabling. Since
we don't exactly know how the firmware (both DMC and PCU) synchronizes
against the actual power well state during DC transitions, make the
disabling also synchronous.
Imre Deak [Tue, 5 Apr 2016 10:26:05 +0000 (13:26 +0300)]
drm/i915/gen9: Reset secondary power well requests left on by DMC/KVMR
DMC forces on power well 1 and the misc IO power well by setting the
corresponding request bits both in the BIOS and the DEBUG power well
request registers. This is somewhat unexpected since the firmware should
really just save and restore state but not alter it. We also depend on
being able to disable power well 1, and the misc IO power well before
entering S3/S4 on BXT and SKL or entering DC9 on BXT. To fix this make
sure these request bits are cleared whenever we want to disable the
given power wells.
On SKL there is another twist where the firmware also clears the power
well 1 request bit in HSW_POWER_WELL_DRIVER (but not that of the misc IO
power well). This happens to not cause a problem due to the forced-on
request bits in the other request registers.
I've filed a bug about all this, but fixing that may take a while and
having this sanity check in place makes sense even for future firmware
versions.
At the same time also check the KVMR request bits. I haven't seen this
being altered, but we don't expect any request bits in here either, so
sanitize this register as well.
v2:
- Apply the workaround on SKL as well. I noticed the related failure
from the CI report, later Patrik also reported seeing it on his
machine.
Imre Deak [Fri, 1 Apr 2016 13:02:34 +0000 (16:02 +0300)]
drm/i915/bxt: Add a note about BXT_PORT_CL1CM_DW30 being read-only
This register is read-only, so we have never actually set
OCL2_LDOFUSE_PWR_DIS in it as specified by the specification. Add a code
comment about this. I filed a specification update request to clarify
this there.
Imre Deak [Fri, 1 Apr 2016 13:02:33 +0000 (16:02 +0300)]
drm/i915/bxt: Fix GRC code register field definitions
This has been corrected in BSpec quite some time ago, but we missed it
somehow. The wrong field definitions resulted in configuring PHY0 with
an incorrect GRC value.
v2:
- Remove the FIXME comment, we left in the code exactly about this
issue. (Ville)
Imre Deak [Fri, 1 Apr 2016 13:02:32 +0000 (16:02 +0300)]
drm/i915/bxt: Reject DMC firmware versions with known bugs
DMC version 1.06 has a known bug, where the firmware polls forever for a
port PLL to lock, if the PLL was disabled when entering DC5, which locks
up the machine. Version 1.07 fixes this, so make that the minimum
required version on BXT.
Ville Syrjälä [Wed, 13 Apr 2016 18:19:56 +0000 (21:19 +0300)]
drm/i915: Move gt/pm irq handling out from irq disabled section on VLV
No need to actually handle the GT/PM interrupt while we have interrupt
sources disabled. Move the actual processing to happen after we've
restored VLV_IER and master interrupt enable.
Ville Syrjälä [Wed, 13 Apr 2016 18:19:54 +0000 (21:19 +0300)]
drm/i915: Split PORT_HOTPLUG_STAT ack out from i9xx_hpd_irq_handler()
Split the VLV/CHV hoplug irq handling to ack and handler phases. This
way we can move the actual irq handling outside the section where
we have disabled the interrupt sources.
For now, we leave things as is for pre-VLV GMCH platforms, but
eventually they could get the same treatment.
Ville Syrjälä [Wed, 13 Apr 2016 18:19:52 +0000 (21:19 +0300)]
drm/i915: Eliminate loop from VLV irq handler
Now that we've dealt with the races in clearing IIR bits via VLV_IER
and the master interrupt enable, we can go ahead aliminate the loop
from the VLV interrupt handler.
Ville Syrjälä [Wed, 13 Apr 2016 18:19:51 +0000 (21:19 +0300)]
drm/i915: Clear VLV_IER around irq processing
On VLV/CHV the master interrupt enable bit only affects GT/PM
interrupts. Display interrupts are not affected by the master
irq control.
Also it seems that the CPU interrupt will only be generated when
the combined result of all GT/PM/display interrupts has a 0->1
edge. We already use the master interrupt enable bit to make sure
GT/PM interrupt can generate such an edge if we don't end up clearing
all IIR bits. We must do the same for display interrupts, and for
that we can simply clear out VLV_IER, and restore after we've acked
all the interrupts we are about to process.
So with both master interrupt enable and VLV_IER cleared out, we will
guarantee that there will be a 0->1 edge if any IIR bits are still set
at the end, and thus another CPU interrupt will be generated.
Ville Syrjälä [Wed, 13 Apr 2016 18:19:50 +0000 (21:19 +0300)]
drm/i915: Clear VLV_MASTER_IER around irq processing
Like on CHV, let's clear out the master irq enable bit when we ack
GT/PM interrupts. This will allow GT/PM interrupts to re-raise the
CPU interrupt if we fail to clear all the bits from the IIR(s).
Ville Syrjälä [Wed, 13 Apr 2016 18:19:49 +0000 (21:19 +0300)]
drm/i915: Clear VLV_IIR after PIPESTAT
On VLV/CHV VLV_IIR is not double double buffered, and it doesn't detect
edges from PIPESTAT & co. like it does on gen4. Instead it just
directly latches the level from PIPESTAT & co. That means we must clear
VLV_IIR after PIPESTAT & co. or else we'll get a spurious bit in VLV_IIR
every single time.
Ville Syrjälä [Wed, 13 Apr 2016 18:19:48 +0000 (21:19 +0300)]
drm/i915: Set up VLV_MASTER_IER consistently
We're lacking VLV_MASTER_IER setup from valleyview_irq_preinstall(), so
add it there. Also cargo cult in some POSTING_READ()s to match the other
platforms.
Ville Syrjälä [Wed, 13 Apr 2016 18:19:47 +0000 (21:19 +0300)]
drm/i915: Use GEN8_MASTER_IRQ_CONTROL consistently
Use GEN8_MASTER_IRQ_CONTROL instead of DE_MASTER_IRQ_CONTROL or
MASTER_INTERRUPT_ENABLE with the GEN8_MASTER_IRQ register. They're
all bit 31 so there's no actual bug here, but let's be consistent
which name we use for the bit.
Ville Syrjälä [Wed, 13 Apr 2016 18:09:30 +0000 (21:09 +0300)]
drm/i915: Ignore GTFIFODBG FIFO free entry fields on CHV
On CHV GTFIFODBG has some read-only bits to indicate the number
of free FIFO entries. Ignore these when checking to see if any
of the sticky error bits are set.
This gets rid of these during device resume:
[drm:cherryview_enable_rps] GT fifo had a previous error 1080000
While at it, move the assignments out of the if().
Peter Antoine [Wed, 13 Apr 2016 14:03:25 +0000 (15:03 +0100)]
drm/i915/mocs: Program MOCS for all engines on init
Allow for the MOCS to be programmed for all engines.
Currently we program the MOCS when the first render batch
goes through. This works on most platforms but fails on
platforms that do not run a render batch early,
i.e. headless servers. The patch now programs all initialised engines
on init and the RCS is programmed again within the initial batch. This
is done for predictable consistency with regards to the hardware
context.
Hardware context loading sets the values of the MOCS for RCS
and L3CC. Programming them from within the batch makes sure that
the render context is valid, no matter what the previous state of
the saved-context was.
v2: posted correct version to the mailing list.
v3: moved programming to within engine->init_hw() (Chris Wilson)
v4: code formatting and white-space changes. (Chris Wilson)
Chris Wilson [Wed, 13 Apr 2016 16:35:15 +0000 (17:35 +0100)]
drm/i915: Late request cancellations are harmful
Conceptually, each request is a record of a hardware transaction - we
build up a list of pending commands and then either commit them to
hardware, or cancel them. However, whilst building up the list of
pending commands, we may modify state outside of the request and make
references to the pending request. If we do so and then cancel that
request, external objects then point to the deleted request leading to
both graphical and memory corruption.
The easiest example is to consider object/VMA tracking. When we mark an
object as active in a request, we store a pointer to this, the most
recent request, in the object. Then we want to free that object, we wait
for the most recent request to be idle before proceeding (otherwise the
hardware will write to pages now owned by the system, or we will attempt
to read from those pages before the hardware is finished writing). If
the request was cancelled instead, that wait completes immediately. As a
result, all requests must be committed and not cancelled if the external
state is unknown.
All that remains of i915_gem_request_cancel() users are just a couple of
extremely unlikely allocation failures, so remove the API entirely.
A consequence of committing all incomplete requests is that we generate
excess breadcrumbs and fill the ring much more often with dummy work. We
have completely undone the outstanding_last_seqno optimisation.
Chris Wilson [Wed, 13 Apr 2016 16:35:14 +0000 (17:35 +0100)]
drm/i915: Reorganise legacy context switch to cope with late failure
After mi_set_context() succeeds, we need to update the state of the
engine's last_context. This ensures that we hold a pin on the context
whilst the hardware may write to it. However, since we didn't complete
the post-switch setup of the context, we need to force the subsequent
use of the same context to complete the setup (which means updating
should_skip_switch()).
projects / linux-beck.git / log