Johan Hedberg [Wed, 22 Feb 2012 20:11:32 +0000 (22:11 +0200)]
Bluetooth: mgmt: Allow class of device changes while powered off
This patch makes it possible to set the class when powered off. When
powering on the right class of device value will be automatically
writen to the controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 22 Feb 2012 19:39:58 +0000 (21:39 +0200)]
Bluetooth: mgmt: Fix name_changed event for short name changes
Since we can't reliably track the short name changes just assume that we
had a change whenever there's a pending mgmt command. In the worst case
we just get one unnecessary name_changed signal.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 22 Feb 2012 19:06:55 +0000 (21:06 +0200)]
Bluetooth: mgmt: Allow local name changes while powered off
This patch makes it possible to set the local name before powering on
the device. The name will be applied using the hci_write_local_name
command once the device gets powered on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 22 Feb 2012 18:14:22 +0000 (20:14 +0200)]
Bluetooth: Fix read_name updating when HCI_SETUP is not set
The local name should only be updated as a consequence of a
hci_read_local_name if we are in the HCI_SETUP state. In all other
scenarios it should only be updated through hci_write_local_name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 22 Feb 2012 17:19:09 +0000 (19:19 +0200)]
Bluetooth: Add hdev->short_name for EIR generation
It's possible to provide a short name through the mgmt interface and
this name can be used for EIR generation when the full name doesn't fit
there. This patch adds the preliminary tracking of the provided short
name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Wed, 22 Feb 2012 17:21:00 +0000 (18:21 +0100)]
Bluetooth: Fix handling of discoverable setting with timeout
The current handling of the discoverable timeout was missing the proper
handling of the timeout when the mode was already set. Now the command
can be used to expire or retrigger the timeout.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg [Wed, 22 Feb 2012 16:17:32 +0000 (18:17 +0200)]
Bluetooth: mgmt: Fix updating EIR when updating the name
Whenever we update the local device name the EIR data also needs to be
updated to reflect this. The update_eir() function in mgmt.c depends on
hdev->dev_name to be up to date so the patch also makes sure that the
mgmt function is called from hci_event.c after the update has happened.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 22 Feb 2012 16:11:53 +0000 (18:11 +0200)]
Bluetooth: Fix EIR data clearing when powering off
When powering off we should assume that the EIR data isn't valid
anymore. This patch makes sure it gets cleared in hci_dev_do_close and
thereby ensures that a correct new EIR is recreated when powering on
again.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 22 Feb 2012 14:37:11 +0000 (16:37 +0200)]
Bluetooth: mgmt: Implement Set LE command
This patch implements support for the Set LE mgmt command. Now, in
addition to the enable_le module parameter user space needs to send an
explicit Enable LE command to enable LE support.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 22 Feb 2012 14:35:26 +0000 (16:35 +0200)]
Bluetooth: mgmt: Fix Set SSP supported check
The test for SSP support needs to be earlier in the set_ssp function so
that we return an error when SSP is not supported even when the device
is powered off.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Wed, 22 Feb 2012 12:49:28 +0000 (13:49 +0100)]
Bluetooth: Enable timestamps for control channel
The control channel can be also monitored, so include timestamps here
as well. And make sure management events get their timestamp when they
are created.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg [Wed, 22 Feb 2012 13:38:48 +0000 (15:38 +0200)]
Bluetooth: mgmt: Fix clearing of hdev->eir
The hdev->eir buffer needs to be cleared when clearing the EIR data.
Otherwise subsequent attempts at setting the EIR to something valid
again may fail because the code thinks that the EIR hasn't changed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 22 Feb 2012 10:28:39 +0000 (12:28 +0200)]
Bluetooth: Remove unneeded hci_cc_read_ssp_mode function
The kernel has no need to track the hci_read_ssp_mode command since it
has the hci_sent_cmd_data function to check what value was set when
hci_write_ssp_mode completes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Wed, 22 Feb 2012 09:58:37 +0000 (11:58 +0200)]
Bluetooth: mgmt: Make Set Link Security callable while powered off
This patch makes it possible to change the Link Security setting while
powered off and have it automatically enabled when powering on a device.
To track the desired state once powered on a new HCI_LINK_SECURITY flag
is added.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Usage of RCU list looks not reasonalbe for a number of reasons:
our code sleep and we had to use socket spinlocks. Most parts
of code are updaters thus there is little sense to use RCU.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Reviewed-by: Ulisses Furquim <ulisses@profusion.mobi> Acked-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg [Tue, 21 Feb 2012 17:40:05 +0000 (19:40 +0200)]
Bluetooth: mgmt: Fix New Settings event for connectable/discoverable
When powered off and doing changes to the Connectable or Discoverable
setting we should also send an appropriate New Settings event in
addition to the command response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Tue, 21 Feb 2012 14:01:30 +0000 (16:01 +0200)]
Bluetooth: mgmt: Allow connectable/discoverable changes in off state
This patch makes it possible to toggle the connectable & discoverable
settings when powered off. Two new hdev->dev_flags flags are added to
track what the scan mode should be when the device is finally powered
on.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Tue, 21 Feb 2012 15:25:22 +0000 (17:25 +0200)]
Bluetooth: mgmt: Fix pairable setting upon initialization
When mgmt is not in use the HCI_PAIRABLE flag will get implicitly set so
that pairing still works with old user space versions. However, as soon
as mgmt comes into play we should clear this flag so that it can be
properly set through the set_pairable command by user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch ensures that Set Fast Connectable fails apropriately if we
are not already in a connectable state (which is a pre-requisite for
fast connectable).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Tue, 21 Feb 2012 12:13:02 +0000 (14:13 +0200)]
Bluetooth: mgmt: Fix powered checks for commands
Having the HCI_AUTO_OFF flag set means that from a mgmt interface
perspective we're still not powered, so all tests for HCI_UP should also
include a test for HCI_AUTO_OFF. This patch adds a convenience macro for
it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Tue, 21 Feb 2012 11:14:25 +0000 (12:14 +0100)]
Bluetooth: Only keep controller up after init if powered on
When a new controller gets added to the system, it needs to be brought
up briefly to read basic information like features, BD_ADDR etc. and
after a timeout it will be brought back down.
The only command that should overwrite this timeout is the set power
command from the management interface. Just reading the controller
list or information is not a good reason to keep the controller up.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg [Mon, 20 Feb 2012 22:52:42 +0000 (00:52 +0200)]
Bluetooth: mgmt: Clear EIR data when disabling SSP
EIR shouldn't be enabled if SSP isn't enabled. This patch adds the
clearing of EIR data when disabling SSP and restores the data when SSP
is re-enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Mon, 20 Feb 2012 20:24:37 +0000 (21:24 +0100)]
Bluetooth: Always enable management interface
The management interface API has reached stable version 1.0 and thus
it can now be always enabled. All future changes will be made backwards
compatible.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Mon, 20 Feb 2012 19:34:38 +0000 (20:34 +0100)]
Bluetooth: Add support for HCI monitor channel
The HCI monitor channel can be used to monitor all packets and events
from the Bluetooth subsystem. The monitor is not bound to any specific
HCI device and allows even capturing multiple devices at the same time.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Mon, 20 Feb 2012 13:50:37 +0000 (14:50 +0100)]
Bluetooth: Remove HCI notifier handling
The HCI notifier handling was never used outside of Bluetooth core layer
and thus remove it and replace it with direct function calls. Also move
the stack internal event generation into the HCI socket layer.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Mon, 20 Feb 2012 13:50:36 +0000 (14:50 +0100)]
Bluetooth: Fix issue with shared SKB between HCI raw socket and driver
Any HCI raw socket gets a copy of each SKB that is either received or
send via the Bluetooth subsystem. The raw socket uses SKB clones to
send out data, but the problem is that it needs to add an extra packet
type byte in front of it. And some drivers need to also add an extra
header before submitting the packet.
So far this all worked magically fine since all of the drivers and the
raw sockets are adding the same byte at the same location. But that is
by pure coincidence. Since the data of cloned SKBs is shared, this means
that the raw socket and driver kept writing into the shared data area.
To fix this the only safe way is if the HCI raw socket creates a copy of
the SKB before sending it out. To not always copy all SKBs around, the
copy is only created once and only after any of the HCI filter checks
succeeded.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Mon, 20 Feb 2012 13:50:32 +0000 (14:50 +0100)]
Bluetooth: Limit HCI raw socket options to actual raw sockets
Currently the socket options of HCI sockets can be set on raw and control
sockets, but on control sockets they make no sense. So just return EINVAL
in that case.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt_cb(skb)->channel was only needed to make hci_send_to_sock() be
used for HCI raw and control sockets. Since they have now separate sending
functions this is no longer needed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Marcel Holtmann [Mon, 20 Feb 2012 13:50:30 +0000 (14:50 +0100)]
Bluetooth: Split sending for HCI raw and control sockets
The sending functions for HCI raw and control sockets have nothing in
common except that they iterate over the socket list. Split them into
two so they can do their job more efficient. In addition the code becomes
more readable.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg [Sun, 19 Feb 2012 12:06:48 +0000 (14:06 +0200)]
Bluetooth: Fix hci_connect error return values
The hci_connect function should either return a valid hci_conn pointer
or a ERR_PTR() but never NULL. This patch fixes the two places where
hci_conn_add failures would have caused a NULL return. The only reason
for failure with hci_conn_add is memory allocation so ENOMEM seems to be
a good choice here.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Fri, 17 Feb 2012 12:39:28 +0000 (14:39 +0200)]
Bluetooth: mgmt: Bump mgmt version
This patch bumps the mgmt version to 1 and resets the revision to 0.
This is in order to indicate API stability to user space. The mgmt API
has reached a point where no major backwards incompatible changes are
expected so it makes sense to do this version bump now.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg [Sat, 18 Feb 2012 13:07:59 +0000 (15:07 +0200)]
Bluetooth: mgmt: Move status parameters into the cmd_complete header
Instead of having status paramters part of each individual command
response it's simpler to just have the status as part of the command
complete header. This patch updates the code to follow this convention
and thereby also ensures compliance with the latest mgmt API
specification.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Andre Guedes [Fri, 17 Feb 2012 23:39:37 +0000 (20:39 -0300)]
Bluetooth: Merge INQUIRY and LE_SCAN discovery states
This patch merges DISCOVERY_INQUIRY and DISCOVERY_LE_SCAN states
into a new state called DISCOVERY_FINDING.
From the discovery perspective, we are pretty much worried about
to know just if we are finding devices than what exactly phase of
"finding devices" (inquiry or LE scan) we are currently running.
Besides, to know if the controller is performing inquiry or LE scan
we should check HCI_INQUIRY or HCI_LE_SCAN bits in hdev flags.
Moreover, merging this two states will simplify the discovery state
machine and will keep interleaved discovery implementation simpler.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg [Thu, 16 Feb 2012 21:56:27 +0000 (23:56 +0200)]
Bluetooth: mgmt: Add support for Set Link Security command
The Set Link Security mgmt command is used to enable or disable link
level security, also known as Security Mode 3. This is rarely enabled in
modern systems but the command needs to be available for completeness,
qualification purposes and those few systems that actually want to
enable it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Pavel Roskin [Sat, 11 Feb 2012 15:01:53 +0000 (10:01 -0500)]
ath9k: stop on rates with idx -1 in ath9k rate control's .tx_status
Rate control algorithms are supposed to stop processing when they
encounter a rate with the index -1. Checking for rate->count not being
zero is not enough.
Allowing a rate with negative index leads to memory corruption in
ath_debug_stat_rc().
One consequence of the bug is discussed at
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Signed-off-by: Pavel Roskin <proski@gnu.org> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar [Fri, 10 Feb 2012 02:32:22 +0000 (18:32 -0800)]
mwifiex: clear previous security setting during association
Driver maintains different flags for WEP, WPA, WPA2 security modes.
Appropriate flag is set using security information provided in
connect request. mwifiex_is_network_compatible() routine uses them
to check if driver's setting is compatible with AP. Association is
aborted if the routine fails.
For some corner cases, it is observed that association is failed
even for valid security information based on association history.
This patch fixes the problem by clearing previous security setting
during each association.
We should set WEP key provided in connect request as default tx key.
This missing change is also added here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Wed, 8 Feb 2012 18:17:11 +0000 (19:17 +0100)]
mac80211: do not call rate control .tx_status before .rate_init
Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Tested-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 20 Jan 2012 12:55:23 +0000 (13:55 +0100)]
mac80211: call rate control only after init
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andre Guedes [Mon, 13 Feb 2012 18:41:02 +0000 (15:41 -0300)]
Bluetooth: Fix event sending with DISCOVERY_STOPPED state
We are not supposed to send mgmt_discovering events if we are transiting
from DISCOVERY_STARTING to DISCOVERY_STOPPED state. It doesn't make
sense to send mgmt_discovering event once discovery procedure has not
been even started.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Andre Guedes [Mon, 13 Feb 2012 18:41:01 +0000 (15:41 -0300)]
Bluetooth: Fix discovery state machine
In case of Start Discovery command failure, we should set the discovery
state to DISCOVERY_STOPPED. Otherwise, we stuck at DISCOVERY_STARTING
state and subsequent Start Discovery commands will simply fail.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Johan Hedberg [Mon, 13 Feb 2012 14:59:33 +0000 (16:59 +0200)]
Bluetooth: Implement Read Supported Commands commands for mgmt
This patch implements the Read Supported Commands mgmt command which was
recently added to the API specification. It returns a list of supported
commands and events to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org>
Ulisses Furquim [Mon, 30 Jan 2012 20:26:29 +0000 (18:26 -0200)]
Bluetooth: Fix possible use after free in delete path
We need to use the _sync() version for cancelling the info and security
timer in the L2CAP connection delete path. Otherwise the delayed work
handler might run after the connection object is freed.
Ulisses Furquim [Mon, 30 Jan 2012 20:26:28 +0000 (18:26 -0200)]
Bluetooth: Remove usage of __cancel_delayed_work()
__cancel_delayed_work() is being used in some paths where we cannot
sleep waiting for the delayed work to finish. However, that function
might return while the timer is running and the work will be queued
again. Replace the calls with safer cancel_delayed_work() version
which spins until the timer handler finishes on other CPUs and
cancels the delayed work.
projects / mv-sheeva.git / log