David Forster [Fri, 6 Jan 2017 10:27:59 +0000 (10:27 +0000)]
vti6: fix device register to report IFLA_INFO_KIND
vti6 interface is registered before the rtnl_link_ops block
is attached. As a result the resulting RTM_NEWLINK is missing
IFLA_INFO_KIND. Re-order attachment of rtnl_link_ops block to fix.
Signed-off-by: Dave Forster <dforster@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For proper IRQ generation by DP83867 phy the INT/PWDN pin has to be
programmed as an interrupt output instead of a Powerdown input in
Configuration Register 3 (CFG3), Address 0x001E, bit 7 INT_OE = 1. The
current driver doesn't do this and as result IRQs will not be generated by
DP83867 phy even if they are properly configured in DT.
Hence, fix IRQ generation by properly configuring CFG3.INT_OE bit and
ensure that Link Status Change (LINK_STATUS_CHNG_INT) and Auto-Negotiation
Complete (AUTONEG_COMP_INT) interrupt are enabled. After this the DP83867
driver will work properly in interrupt enabled mode.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
amd-xgbe: Fix IRQ processing when running in single IRQ mode
When running in single IRQ mode, the additional IRQ routines were being
skipped because only the XGMAC interrupt status was being checked.
Update the code so that the additional IRQ routines are checked whenever
an interrupt is received.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Wed, 4 Jan 2017 21:29:32 +0000 (00:29 +0300)]
sh_eth: R8A7740 supports packet shecksumming
The R8A7740 GEther controller supports the packet checksum offloading
but the 'hw_crc' (bad name, I'll fix it) flag isn't set in the R8A7740
data, thus CSMR isn't cleared...
Fixes: 73a0d907301e ("net: sh_eth: add support R8A7740") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Wed, 4 Jan 2017 19:18:24 +0000 (22:18 +0300)]
sh_eth: fix EESIPR values for SH77{34|63}
As the SH77{34|63} manuals are freely available, I've checked the EESIPR
values written against the manuals, and they appeared to set the reserved
bits 11-15 (which should be 0 on write). Fix those EESIPR values.
Fixes: 380af9e390ec ("net: sh_eth: CPU dependency code collect to "struct sh_eth_cpu_data"") Fixes: f5d12767c8fd ("sh_eth: get SH77{34|63} support out of #ifdef") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following patchset contains accumulated Netfilter fixes for your
net tree:
1) Ensure quota dump and reset happens iff we can deliver numbers to
userspace.
2) Silence splat on incorrect use of smp_processor_id() from nft_queue.
3) Fix an out-of-bound access reported by KASAN in
nf_tables_rule_destroy(), patch from Florian Westphal.
4) Fix layer 4 checksum mangling in the nf_tables payload expression
with IPv6.
5) Fix a race in the CLUSTERIP target from control plane path when two
threads run to add a new configuration object. Serialize invocations
of clusterip_config_init() using spin_lock. From Xin Long.
6) Call br_nf_pre_routing_finish_bridge_finish() once we are done with
the br_nf_pre_routing_finish() hook. From Artur Molchanov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 5 Jan 2017 02:33:35 +0000 (18:33 -0800)]
Merge tag 'xfs-for-linus-4.10-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
- fixes for crashes and double-cleanup errors
- XFS maintainership handover
- fix to prevent absurdly large block reservations
- fix broken sysfs getter/setters
* tag 'xfs-for-linus-4.10-rc3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix max_retries _show and _store functions
xfs: update MAINTAINERS
xfs: fix crash and data corruption due to removal of busy COW extents
xfs: use the actual AG length when reserving blocks
xfs: fix double-cleanup when CUI recovery fails
1) stmmac_drv_probe() can race with stmmac_open() because we register
the netdevice too early. Fix from Florian Fainelli.
2) UFO handling in __ip6_append_data() and ip6_finish_output() use
different tests for deciding whether a frame will be fragmented or
not, put them in sync. Fix from Zheng Li.
3) The rtnetlink getstats handlers need to validate that the netlink
request is large enough, fix from Mathias Krause.
4) Use after free in mlx4 driver, from Jack Morgenstein.
5) Fix setting of garbage UID value in sockets during setattr() calls,
from Eric Biggers.
6) Packet drop_monitor doesn't format the netlink messages properly
such that nlmsg_next fails to work, fix from Reiter Wolfgang.
7) Fix handling of wildcard addresses in l2tp lookups, from Guillaume
Nault.
8) __skb_flow_dissect() can crash on pptp packets, from Ian Kumlien.
9) IGMP code doesn't reset group query timers properly, from Michal
Tesar.
10) Fix overzealous MAIN/LOCAL route table combining in ipv4, from
Alexander Duyck.
11) vxlan offload check needs to be more strict in be2net driver, from
Sabrina Dubroca.
12) Moving l3mdev to packet hooks lost RX stat counters unintentionally,
fix from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sh_eth: enable RX descriptor word 0 shift on SH7734
sfc: don't report RX hash keys to ethtool when RSS wasn't enabled
dpaa_eth: Initialize CGR structure before init
dpaa_eth: cleanup after init_phy() failure
net: systemport: Pad packet before inserting TSB
net: systemport: Utilize skb_put_padto()
LiquidIO VF: s/select/imply/ for PTP_1588_CLOCK
libcxgb: fix error check for ip6_route_output()
net: usb: asix_devices: add .reset_resume for USB PM
net: vrf: Add missing Rx counters
drop_monitor: consider inserted data in genlmsg_end
benet: stricter vxlan offloading check in be_features_check
ipv4: Do not allow MAIN to be alias for new LOCAL w/ custom rules
net: macb: Updated resource allocation function calls to new version of API.
net: stmmac: dwmac-oxnas: use generic pm implementation
net: stmmac: dwmac-oxnas: fix fixed-link-phydev leaks
net: stmmac: dwmac-oxnas: fix of-node leak
Documentation/networking: fix typo in mpls-sysctl
igmp: Make igmp group member RFC 3376 compliant
flow_dissector: Update pptp handling to avoid null pointer deref.
...
Sergei Shtylyov [Wed, 4 Jan 2017 20:10:23 +0000 (23:10 +0300)]
sh_eth: enable RX descriptor word 0 shift on SH7734
The RX descriptor word 0 on SH7734 has the RFS[9:0] field in bits 16-25
(bits 0-15 usually used for that are occupied by the packet checksum).
Thus we need to set the 'shift_rd0' field in the SH7734 SoC data...
Fixes: f0e81fecd4f8 ("net: sh_eth: Add support SH7734") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Wed, 4 Jan 2017 15:10:56 +0000 (15:10 +0000)]
sfc: don't report RX hash keys to ethtool when RSS wasn't enabled
If we failed to set up RSS on EF10 (e.g. because firmware declared
RX_RSS_LIMITED), ethtool --show-nfc $dev rx-flow-hash ... should report
no fields, rather than confusingly reporting what fields we _would_ be
hashing on if RSS was working.
Fixes: dcb4123cbec0 ("sfc: disable RSS when unsupported") Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: systemport: Fix padding vs. TSB insertion
This patch series fixes how we pad the packets submitted to the SYSTEMPORT
adapter, and how the transmit status block (prepended 8 bytes) fits in the
picture. The first patch is not technically a bug fix, but is required for the
second path to be applied and to greatly simplify the skb length calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Inserting the TSB means adding an extra 8 bytes in front the of packet
that is going to be used as metadata information by the TDMA engine, but
stripped off, so it does not really help with the packet padding.
For some odd packet sizes that fall below the 60 bytes payload (e.g: ARP)
we can end-up padding them after the TSB insertion, thus making them 64
bytes, but with the TDMA stripping off the first 8 bytes, they could
still be smaller than 64 bytes which is required to ingress the switch.
Fix this by swapping the padding and TSB insertion, guaranteeing that
the packets have the right sizes.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since we need to pad our packets, utilize skb_put_padto() which
increases skb->len by how much we need to pad, allowing us to eliminate
the test on skb->len right below.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Pitre [Tue, 3 Jan 2017 18:57:00 +0000 (13:57 -0500)]
LiquidIO VF: s/select/imply/ for PTP_1588_CLOCK
Fix a minor fallout from the merge of the timers and the networking
trees. The following error may result if the PTP_1588_CLOCK
prerequisites are not available:
drivers/built-in.o: In function `ptp_clock_unregister':
(.text+0x40e0a5): undefined reference to `pps_unregister_source'
drivers/built-in.o: In function `ptp_clock_unregister':
(.text+0x40e0cc): undefined reference to `posix_clock_unregister'
drivers/built-in.o: In function `ptp_clock_event':
(.text+0x40e249): undefined reference to `pps_event'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e5e1): undefined reference to `pps_register_source'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e62c): undefined reference to `posix_clock_register'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e68d): undefined reference to `pps_unregister_source'
Signed-off-by: Nicolas Pitre <nico@linaro.org> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Chen [Tue, 3 Jan 2017 09:22:20 +0000 (17:22 +0800)]
net: usb: asix_devices: add .reset_resume for USB PM
The USB core may call reset_resume when it fails to resume asix device.
And USB core can recovery this abnormal resume at low level driver,
the same .resume at asix driver can work too. Add .reset_resume can
avoid disconnecting after backing from system resume, and NFS can
still be mounted after this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 4 Jan 2017 17:03:37 +0000 (09:03 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"A set of fixes for the current series, one fixing a regression with
block size < page cache size in the alias series from Jan. Outside of
that, two small cleanups for wbt from Bart, a nvme pull request from
Christoph, and a few small fixes of documentation updates"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix up io_poll documentation
block: Avoid that sparse complains about context imbalance in __wbt_wait()
block: Make wbt_wait() definition consistent with declaration
clean_bdev_aliases: Prevent cleaning blocks that are not in block range
genhd: remove dead and duplicated scsi code
block: add back plugging in __blkdev_direct_IO
nvmet/fcloop: remove some logically dead code performing redundant ret checks
nvmet: fix KATO offset in Set Features
nvme/fc: simplify error handling of nvme_fc_create_hw_io_queues
nvme/fc: correct some printk information
nvme/scsi: Remove START STOP emulation
nvme/pci: Delete misleading queue-wrap comment
nvme/pci: Fix whitespace problem
nvme: simplify stripe quirk
nvme: update maintainers information
Linus Torvalds [Wed, 4 Jan 2017 17:00:57 +0000 (09:00 -0800)]
Merge tag 'fbdev-v4.10-rc2' of git://github.com/bzolnier/linux
Pull fbdev fixes from Bartlomiej Zolnierkiewicz:
- bring fbdev subsystem back into Maintained mode
- add missing devm_ioremap() error checking to cobalt_lcdfb driver
* tag 'fbdev-v4.10-rc2' of git://github.com/bzolnier/linux:
video: fbdev: cobalt_lcdfb: Handle return NULL error from devm_ioremap
MAINTAINERS: add myself as maintainer of fbdev
Linus Torvalds [Wed, 4 Jan 2017 16:56:05 +0000 (08:56 -0800)]
Merge tag 'gcc-plugins-v4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc-plugins fixes from Kees Cook:
"Small fixes for gcc-plugins when using certain gcc versions:
- update gcc-common.h for gcc 7 (Emese Revfy)
- fix latent_entropy type for early gcc on ARM (PaX Team)"
* tag 'gcc-plugins-v4.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: update gcc-common.h for gcc-7
latent_entropy: fix ARM build error on earlier gcc
Arvind Yadav [Tue, 13 Dec 2016 08:20:52 +0000 (13:50 +0530)]
video: fbdev: cobalt_lcdfb: Handle return NULL error from devm_ioremap
Here, If devm_ioremap will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference.
This error check will avoid NULL pointer dereference.
Carlos Maiolino [Wed, 4 Jan 2017 04:34:17 +0000 (20:34 -0800)]
xfs: fix max_retries _show and _store functions
max_retries _show and _store functions should test against cfg->max_retries,
not cfg->retry_timeout
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
xfs: fix crash and data corruption due to removal of busy COW extents
There is a race window between write_cache_pages calling
clear_page_dirty_for_io and XFS calling set_page_writeback, in which
the mapping for an inode is tagged neither as dirty, nor as writeback.
If the COW shrinker hits in exactly that window we'll remove the delayed
COW extents and writepages trying to write it back, which in release
kernels will manifest as corruption of the bmap btree, and in debug
kernels will trip the ASSERT about now calling xfs_bmapi_write with the
COWFORK flag for holes. A complex customer load manages to hit this
window fairly reliably, probably by always having COW writeback in flight
while the cow shrinker runs.
This patch adds another check for having the I_DIRTY_PAGES flag set,
which is still set during this race window. While this fixes the problem
I'm still not overly happy about the way the COW shrinker works as it
still seems a bit fragile.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Darrick J. Wong [Wed, 4 Jan 2017 02:39:33 +0000 (18:39 -0800)]
xfs: use the actual AG length when reserving blocks
We need to use the actual AG length when making per-AG reservations,
since we could otherwise end up reserving more blocks out of the last
AG than there are actual blocks.
Complained-about-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
David Ahern [Tue, 3 Jan 2017 17:37:55 +0000 (09:37 -0800)]
net: vrf: Add missing Rx counters
The move from rx-handler to L3 receive handler inadvertantly dropped the
rx counters. Restore them.
Fixes: 74b20582ac38 ("net: l3mdev: Add hook in ip and ipv6") Reported-by: Dinesh Dutt <ddutt@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 3 Jan 2017 18:50:05 +0000 (10:50 -0800)]
Merge branch 'parisc-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
- limit usage of processor-internal cr16 clocksource to UP systems only
- segfault info lines in syslog were too long, split those up
- drop own TIF_RESTORE_SIGMASK flag and switch to generic code
* 'parisc-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Add line-break when printing segfault info
parisc: Drop TIF_RESTORE_SIGMASK and switch to generic code
parisc: Mark cr16 clocksource unstable on SMP systems
Reiter Wolfgang [Tue, 3 Jan 2017 00:39:10 +0000 (01:39 +0100)]
drop_monitor: consider inserted data in genlmsg_end
Final nlmsg_len field update must reflect inserted net_dm_drop_point
data.
This patch depends on previous patch:
"drop_monitor: add missing call to genlmsg_end"
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Tue, 3 Jan 2017 15:26:04 +0000 (16:26 +0100)]
benet: stricter vxlan offloading check in be_features_check
When VXLAN offloading is enabled, be_features_check() tries to check if
an encapsulated packet is indeed a VXLAN packet. The check is not strict
enough, and considers any UDP-encapsulated ethernet frame with a 8-byte
tunnel header as being VXLAN. Unfortunately, both GENEVE and VXLAN-GPE
have a 8-byte header, so they get through this check.
Force the UDP destination port to be the one that has been offloaded to
hardware.
Without this, GENEVE-encapsulated packets can end up having an incorrect
checksum when both a GENEVE and a VXLAN (offloaded) tunnel are
configured.
This is similar to commit a547224dceed ("mlx4e: Do not attempt to
offload VXLAN ports that are unrecognized").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 Jan 2017 21:32:54 +0000 (13:32 -0800)]
ipv4: Do not allow MAIN to be alias for new LOCAL w/ custom rules
In the case of custom rules being present we need to handle the case of the
LOCAL table being intialized after the new rule has been added. To address
that I am adding a new check so that we can make certain we don't use an
alias of MAIN for LOCAL when allocating a new table.
Fixes: 0ddcf43d5d4a ("ipv4: FIB Local/MAIN table collapse") Reported-by: Oliver Brunel <jjk@jjacky.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Folta [Mon, 2 Jan 2017 12:41:50 +0000 (12:41 +0000)]
net: macb: Updated resource allocation function calls to new version of API.
Changed function calls of resource allocation to new API. Changed way
of setting DMA mask. Removed unnecessary sanity check.
This patch is sent in regard to recently applied patch
Commit 83a77e9ec4150ee4acc635638f7dedd9da523a26
net: macb: Added PCI wrapper for Platform Driver.
Signed-off-by: Bartosz Folta <bfolta@cadence.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 Jan 2017 14:33:00 +0000 (09:33 -0500)]
Merge branch 'dwmac-oxnas-leaks'
Johan Hovold says:
====================
net: stmmac: dwmac-oxnas: fix leaks and simplify pm
These patches fixes of-node and fixed-phydev leaks in the recently added
dwmac-oxnas driver, and ultimately switches over to using the generic pm
implementation as the required callbacks are now in place.
Note that this series has only been compile tested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link phy registered during
probe on probe errors and on driver unbind by calling the new glue
helper function.
For driver unbind, use the generic stmmac-platform remove implementation
and add an exit callback to disable the clock.
Fixes: 5ed7414062e7 ("net: stmmac: Add OXNAS Glue Driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Mon, 2 Jan 2017 11:56:02 +0000 (12:56 +0100)]
net: stmmac: dwmac-oxnas: fix of-node leak
Use the syscon lookup-by-phandle helper so that the reference taken by
of_parse_phandle() is released when done with the node.
Fixes: 5ed7414062e7 ("net: stmmac: Add OXNAS Glue Driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 3 Jan 2017 02:32:59 +0000 (18:32 -0800)]
Merge tag 'fscrypt-for-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt
Pull fscrypt fixes from Ted Ts'o:
"Two fscrypt bug fixes, one of which was unmasked by an update to the
crypto tree during the merge window"
* tag 'fscrypt-for-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt:
fscrypt: fix renaming and linking special files
fscrypt: fix the test_dummy_encryption mount option
Linus Torvalds [Mon, 2 Jan 2017 20:42:50 +0000 (12:42 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- regression fix (caused by me applying a wrong version of patch) for
sensor-hub driver, from Srinivas Pandruvada
- hid-sony fixes (mostly related to DS4 device) from Roderick
Colenbrander
- three device-specific quirks-fixes from Alex Wood, Brendan McGrath
and Marcel Hasler
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: sensor-hub: Move the memset to sensor_hub_get_feature()
HID: usbhid: Add quirk for Mayflash/Dragonrise DolphinBar.
HID: usbhid: Add quirk for the Futaba TOSD-5711BB VFD
HID: sony: Ignore DS4 dongle reports when no device is connected
HID: sony: Use DS4 MAC address as unique identifier on USB
HID: sony: Fix error handling bug when touchpad registration fails
HID: asus: Fix keyboard support
Michal Tesar [Mon, 2 Jan 2017 13:38:36 +0000 (14:38 +0100)]
igmp: Make igmp group member RFC 3376 compliant
5.2. Action on Reception of a Query
When a system receives a Query, it does not respond immediately.
Instead, it delays its response by a random amount of time, bounded
by the Max Resp Time value derived from the Max Resp Code in the
received Query message. A system may receive a variety of Queries on
different interfaces and of different kinds (e.g., General Queries,
Group-Specific Queries, and Group-and-Source-Specific Queries), each
of which may require its own delayed response.
Before scheduling a response to a Query, the system must first
consider previously scheduled pending responses and in many cases
schedule a combined response. Therefore, the system must be able to
maintain the following state:
o A timer per interface for scheduling responses to General Queries.
o A per-group and interface timer for scheduling responses to Group-
Specific and Group-and-Source-Specific Queries.
o A per-group and interface list of sources to be reported in the
response to a Group-and-Source-Specific Query.
When a new Query with the Router-Alert option arrives on an
interface, provided the system has state to report, a delay for a
response is randomly selected in the range (0, [Max Resp Time]) where
Max Resp Time is derived from Max Resp Code in the received Query
message. The following rules are then used to determine if a Report
needs to be scheduled and the type of Report to schedule. The rules
are considered in order and only the first matching rule is applied.
1. If there is a pending response to a previous General Query
scheduled sooner than the selected delay, no additional response
needs to be scheduled.
2. If the received Query is a General Query, the interface timer is
used to schedule a response to the General Query after the
selected delay. Any previously pending response to a General
Query is canceled.
--8<--
Currently the timer is rearmed with new random expiration time for
every incoming query regardless of possibly already pending report.
Which is not aligned with the above RFE.
It also might happen that higher rate of incoming queries can
postpone the report after the expiration time of the first query
causing group membership loss.
Now the per interface general query timer is rearmed only
when there is no pending report already scheduled on that interface or
the newly selected expiration time is before the already pending
scheduled report.
Signed-off-by: Michal Tesar <mtesar@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ian Kumlien [Mon, 2 Jan 2017 08:18:35 +0000 (09:18 +0100)]
flow_dissector: Update pptp handling to avoid null pointer deref.
__skb_flow_dissect can be called with a skb or a data packet, either
can be NULL. All calls seems to have been moved to __skb_header_pointer
except the pptp handling which is still calling skb_header_pointer.
Fixes: ab10dccb1160 ("rps: Inspect PPTP encapsulated by GRE to get flow hash") Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 2 Jan 2017 17:08:45 +0000 (09:08 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Two bug fixes for 4.10-rc3"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/kbuild: enable modversions for symbols exported from asm
s390/vtime: correct system time accounting
Chandan Rajendra [Sun, 25 Dec 2016 13:31:03 +0000 (19:01 +0530)]
clean_bdev_aliases: Prevent cleaning blocks that are not in block range
The first block to be cleaned may start at a non-zero page offset. In
such a scenario clean_bdev_aliases() will end up cleaning blocks that
do not fall in the range of blocks to be cleaned. This commit fixes the
issue by skipping blocks that do not fall in valid block range.
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Eryu Guan <eguan@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
HID: sensor-hub: Move the memset to sensor_hub_get_feature()
While applying patch d443a0aa3a29: "HID: hid-sensor-hub: clear memory to
avoid random data", there was some issues in applying correct version of
the patch. This resulted in the breakage of sensor functions as all
request like power-up will be reset by the memset() in the function
sensor_hub_set_feature().
The reset of caller buffer should be in the function
sensor_hub_get_feature(), not in the sensor_hub_set_feature().
Marcel Hasler [Tue, 20 Dec 2016 21:08:13 +0000 (22:08 +0100)]
HID: usbhid: Add quirk for Mayflash/Dragonrise DolphinBar.
The DolphinBar by Mayflash (identified as Dragonrise) needs
HID_QUIRK_MULTI_INPUT to split it up into four input devices. Without this
quirk the adapter is falsely recognized as a tablet. See also bug 115841
(https://bugzilla.kernel.org/show_bug.cgi?id=115841).
Johannes Berg [Mon, 2 Jan 2017 10:19:29 +0000 (11:19 +0100)]
mac80211: initialize fast-xmit 'info' later
In ieee80211_xmit_fast(), 'info' is initialized to point to the skb
that's passed in, but that skb may later be replaced by a clone (if
it was shared), leading to an invalid pointer.
This can lead to use-after-free and also later crashes since the
real SKB's info->hw_queue doesn't get initialized properly.
Fix this by assigning info only later, when it's needed, after the
skb replacement (may have) happened.
Cc: stable@vger.kernel.org Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David S. Miller [Mon, 2 Jan 2017 03:07:25 +0000 (22:07 -0500)]
Merge branch 'l2tp-socket-lookup-fixes'
Guillaume Nault says:
====================
l2tp: socket lookup fixes for l2tp_ip and l2tp_ip6
There are still some cases that aren't correctly handled in the socket
lookup functions of l2tp_ip and l2tp_ip6. This series fixes lookups for
connected sockets and for sockets bound to the IPv6 unspecified
address.
bind() and connect() should now work as expected on IPPROTO_L2TP
sockets. Extra features, like SO_REUSEADDR, remain unsupported.
The matching conditions in __l2tp_ip6_bind_lookup() and
__l2tp_ip_bind_lookup() are getting hard to read. I've kept the single
test approach to make the intend of the patches clear. I'll split the
conditionals once these fixes reach net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 30 Dec 2016 18:48:20 +0000 (19:48 +0100)]
l2tp: take remote address into account in l2tp_ip and l2tp_ip6 socket lookups
For connected sockets, __l2tp_ip{,6}_bind_lookup() needs to check the
remote IP when looking for a matching socket. Otherwise a connected
socket can receive traffic not originating from its peer.
Drop l2tp_ip_bind_lookup() and l2tp_ip6_bind_lookup() instead of
updating their prototype, as these functions aren't used.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 30 Dec 2016 18:48:19 +0000 (19:48 +0100)]
l2tp: consider '::' as wildcard address in l2tp_ip6 socket lookup
An L2TP socket bound to the unspecified address should match with any
address. If not, it can't receive any packet and __l2tp_ip6_bind_lookup()
can't prevent another socket from binding on the same device/tunnel ID.
While there, rename the 'addr' variable to 'sk_laddr' (local addr), to
make following patch clearer.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Reiter Wolfgang [Sat, 31 Dec 2016 20:11:57 +0000 (21:11 +0100)]
drop_monitor: add missing call to genlmsg_end
Update nlmsg_len field with genlmsg_end to enable userspace processing
using nlmsg_next helper. Also adds error handling.
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 1 Jan 2017 20:27:05 +0000 (12:27 -0800)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull DAX updates from Dan Williams:
"The completion of Jan's DAX work for 4.10.
As I mentioned in the libnvdimm-for-4.10 pull request, these are some
final fixes for the DAX dirty-cacheline-tracking invalidation work
that was merged through the -mm, ext4, and xfs trees in -rc1. These
patches were prepared prior to the merge window, but we waited for
4.10-rc1 to have a stable merge base after all the prerequisites were
merged.
Quoting Jan on the overall changes in these patches:
"So I'd like all these 6 patches to go for rc2. The first three
patches fix invalidation of exceptional DAX entries (a bug which
is there for a long time) - without these patches data loss can
occur on power failure even though user called fsync(2). The other
three patches change locking of DAX faults so that ->iomap_begin()
is called in a more relaxed locking context and we are safe to
start a transaction there for ext4"
These have received a build success notification from the kbuild
robot, and pass the latest libnvdimm unit tests. There have not been
any -next releases since -rc1, so they have not appeared there"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
ext4: Simplify DAX fault path
dax: Call ->iomap_begin without entry lock during dax fault
dax: Finish fault completely when loading holes
dax: Avoid page invalidation races and unnecessary radix tree traversals
mm: Invalidate DAX radix tree entries only if appropriate
ext2: Return BH_New buffers for zeroed blocks
Eric Biggers [Fri, 30 Dec 2016 23:42:32 +0000 (17:42 -0600)]
net: socket: don't set sk_uid to garbage value in ->setattr()
->setattr() was recently implemented for socket files to sync the socket
inode's uid to the new 'sk_uid' member of struct sock. It does this by
copying over the ia_uid member of struct iattr. However, ia_uid is
actually only valid when ATTR_UID is set in ia_valid, indicating that
the uid is being changed, e.g. by chown. Other metadata operations such
as chmod or utimes leave ia_uid uninitialized. Therefore, sk_uid could
be set to a "garbage" value from the stack.
Fix this by only copying the uid over when ATTR_UID is set.
Fixes: 86741ec25462 ("net: core: Add a UID field to struct sock.") Signed-off-by: Eric Biggers <ebiggers@google.com> Tested-by: Lorenzo Colitti <lorenzo@google.com> Acked-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Biggers [Mon, 19 Dec 2016 22:20:13 +0000 (14:20 -0800)]
fscrypt: fix renaming and linking special files
Attempting to link a device node, named pipe, or socket file into an
encrypted directory through rename(2) or link(2) always failed with
EPERM. This happened because fscrypt_has_permitted_context() saw that
the file was unencrypted and forbid creating the link. This behavior
was unexpected because such files are never encrypted; only regular
files, directories, and symlinks can be encrypted.
To fix this, make fscrypt_has_permitted_context() always return true on
special files.
This will be covered by a test in my encryption xfstests patchset.
Fixes: 9bd8212f981e ("ext4 crypto: add encryption policy and password salt support") Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Richard Weinberger <richard@nod.at> Cc: stable@vger.kernel.org Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Linus Torvalds [Fri, 30 Dec 2016 17:32:26 +0000 (09:32 -0800)]
Merge tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Two small fixes:
- A merge error on my part broke the DocBook build. I've
requisitioned one of tglx's frozen sharks for appropriate
disciplinary action and resolved to be more careful about testing
the DocBook stuff as long as it's still around.
- Fix an error in unaligned-memory-access.txt"
* tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux:
Documentation/unaligned-memory-access.txt: fix incorrect comparison operator
docs: Fix build failure
Artur Molchanov [Fri, 30 Dec 2016 16:46:36 +0000 (19:46 +0300)]
bridge: netfilter: Fix dropping packets that moving through bridge interface
Problem:
br_nf_pre_routing_finish() calls itself instead of
br_nf_pre_routing_finish_bridge(). Due to this bug reverse path filter drops
packets that go through bridge interface.
User impact:
Local docker containers with bridge network can not communicate with each
other.
Fixes: c5136b15ea36 ("netfilter: bridge: add and use br_nf_hook_thresh") Signed-off-by: Artur Molchanov <artur.molchanov@synesis.ru> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David Ahern [Thu, 29 Dec 2016 23:29:03 +0000 (15:29 -0800)]
net: ipv4: dst for local input routes should use l3mdev if relevant
IPv4 output routes already use l3mdev device instead of loopback for dst's
if it is applicable. Change local input routes to do the same.
This fixes icmp responses for unreachable UDP ports which are directed
to the wrong table after commit 9d1a6c4ea43e4 because local_input
routes use the loopback device. Moving from ingress device to loopback
loses the L3 domain causing responses based on the dst to get to lost.
Fixes: 9d1a6c4ea43e4 ("net: icmp_route_lookup should use rt dev to
determine L3 domain") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Thu, 29 Dec 2016 21:07:38 +0000 (00:07 +0300)]
sh_eth: fix branch prediction in sh_eth_interrupt()
IIUC, likely()/unlikely() should apply to the whole *if* statement's
expression, not a part of it -- fix such expression in sh_eth_interrupt()
accordingly...
Fixes: 283e38db65e7 ("sh_eth: Fix serialisation of interrupt disable with interrupt & NAPI handlers") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Thu, 29 Dec 2016 22:16:07 +0000 (14:16 -0800)]
mm/filemap: fix parameters to test_bit()
mm/filemap.c: In function 'clear_bit_unlock_is_negative_byte':
mm/filemap.c:933:9: error: too few arguments to function 'test_bit'
return test_bit(PG_waiters);
^~~~~~~~
Fixes: b91e1302ad9b ('mm: optimize PageWaiters bit use for unlock_page()') Signed-off-by: Olof Johansson <olof@lixom.net> Brown-paper-bag-by: Linus Torvalds <dummy@duh.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Helge Deller [Tue, 27 Dec 2016 17:03:50 +0000 (18:03 +0100)]
parisc: Drop TIF_RESTORE_SIGMASK and switch to generic code
Commit 7e7814180b33 ("signal: consolidate {TS,TLF}_RESTORE_SIGMASK code")
introduced code with which the "restore sigmask" flag lives in task_struct
instead of ti->flags. Let's use this optimization on parisc too.
Helge Deller [Mon, 26 Dec 2016 11:46:01 +0000 (12:46 +0100)]
parisc: Mark cr16 clocksource unstable on SMP systems
The cr16 interval timer of each CPU is not syncronized to other cr16
timers in other CPUs in a SMP system. So, delay the registration of the
cr16 clocksource until all CPUs have been detected and then - if we are
on a SMP machine - mark the cr16 clocksource as unstable and lower it's
rating before registering it at the clocksource framework.
This patch fixes the stalled CPU warnings which we have seen since
introduction of the cr16 clocksource.
Jack Morgenstein [Thu, 29 Dec 2016 16:37:13 +0000 (18:37 +0200)]
net/mlx4_core: Fix raw qp flow steering rules under SRIOV
Demoting simple flow steering rule priority (for DPDK) was achieved by
wrapping FW commands MLX4_QP_FLOW_STEERING_ATTACH/DETACH for the PF
as well, and forcing the priority to MLX4_DOMAIN_NIC in the wrapper
function for the PF and all VFs.
In function mlx4_ib_create_flow(), this change caused the main rule
creation for the PF to be wrapped, while it left the associated
tunnel steering rule creation unwrapped for the PF.
This mismatch caused rule deletion failures in mlx4_ib_destroy_flow()
for the PF when the detach wrapper function did not find the associated
tunnel-steering rule (since creation of that rule for the PF did not
go through the wrapper function).
Fix this by setting MLX4_QP_FLOW_STEERING_ATTACH/DETACH to be "native"
(so that the PF invocation does not go through the wrapper), and perform
the required priority demotion for the PF in the mlx4_ib_create_flow()
code path.
Fixes: 48564135cba8 ("net/mlx4_core: Demote simple multicast and broadcast flow steering rules") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Slava Shwartsman [Thu, 29 Dec 2016 16:37:12 +0000 (18:37 +0200)]
net/mlx4_en: Fix type mismatch for 32-bit systems
is_power_of_2 expects unsigned long and we pass u64 max_val_cycles,
this will be truncated on 32 bit systems, and the result is not what we
were expecting.
div_u64 expects u32 as a second argument and we pass
max_val_cycles_rounded which is u64 hence it will always be truncated.
Fix was tested on both 64 and 32 bit systems and got same results for
max_val_cycles and max_val_cycles_rounded.
Fixes: 4850cf458157 ("net/mlx4_en: Resolve dividing by zero in 32-bit system") Signed-off-by: Slava Shwartsman <slavash@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky [Thu, 29 Dec 2016 16:37:11 +0000 (18:37 +0200)]
net/mlx4: Remove BUG_ON from ICM allocation routine
This patch removes BUG_ON() macro from mlx4_alloc_icm_coherent()
by checking DMA address alignment in advance and performing proper
folding in case of error.
Fixes: 5b0bf5e25efe ("mlx4_core: Support ICM tables in coherent memory") Reported-by: Ozgur Karatas <okaratas@member.fsf.org> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Single send WQE in RX buffer should be stamped with software
ownership in order to prevent the flow of QP in error in FW
once UPDATE_QP is called.
Fixes: 9f519f68cfff ('mlx4_en: Not using Shared Receive Queues') Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 29 Dec 2016 16:37:09 +0000 (18:37 +0200)]
net/mlx4_core: Use-after-free causes a resource leak in flow-steering detach
mlx4_QP_FLOW_STEERING_DETACH_wrapper first removes the steering
rule (which results in freeing the rule structure), and then
references a field in this struct (the qp number) when releasing the
busy-status on the rule's qp.
Since this memory was freed, it could reallocated and changed.
Therefore, the qp number in the struct may be incorrect,
so that we are releasing the incorrect qp. This leaves the rule's qp
in the busy state (and could possibly release an incorrect qp as well).
Fix this by saving the qp number in a local variable, for use after
removing the steering rule.
Fixes: 2c473ae7e582 ("net/mlx4_core: Disallow releasing VF QPs which have steering rules") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Zhang [Thu, 29 Dec 2016 08:45:04 +0000 (16:45 +0800)]
net: fix incorrect original ingress device index in PKTINFO
When we send a packet for our own local address on a non-loopback
interface (e.g. eth0), due to the change had been introduced from
commit 0b922b7a829c ("net: original ingress device index in PKTINFO"), the
original ingress device index would be set as the loopback interface.
However, the packet should be considered as if it is being arrived via the
sending interface (eth0), otherwise it would break the expectation of the
userspace application (e.g. the DHCPRELEASE message from dhcp_release
binary would be ignored by the dnsmasq daemon, since it come from lo which
is not the interface dnsmasq bind to)
Fixes: 0b922b7a829c ("net: original ingress device index in PKTINFO") Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: Wei Zhang <asuka.com@163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We miss to check if the netlink message is actually big enough to contain
a struct if_stats_msg.
Add a check to prevent userland from sending us short messages that would
make us access memory beyond the end of the message.
Fixes: 10c9ead9f3c6 ("rtnetlink: add new RTM_GETSTATS message to dump...") Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 27 Dec 2016 19:40:38 +0000 (11:40 -0800)]
mm: optimize PageWaiters bit use for unlock_page()
In commit 62906027091f ("mm: add PageWaiters indicating tasks are
waiting for a page bit") Nick Piggin made our page locking no longer
unconditionally touch the hashed page waitqueue, which not only helps
performance in general, but is particularly helpful on NUMA machines
where the hashed wait queues can bounce around a lot.
However, the "clear lock bit atomically and then test the waiters bit"
sequence turns out to be much more expensive than it needs to be,
because you get a nasty stall when trying to access the same word that
just got updated atomically.
On architectures where locking is done with LL/SC, this would be trivial
to fix with a new primitive that clears one bit and tests another
atomically, but that ends up not working on x86, where the only atomic
operations that return the result end up being cmpxchg and xadd. The
atomic bit operations return the old value of the same bit we changed,
not the value of an unrelated bit.
On x86, we could put the lock bit in the high bit of the byte, and use
"xadd" with that bit (where the overflow ends up not touching other
bits), and look at the other bits of the result. However, an even
simpler model is to just use a regular atomic "and" to clear the lock
bit, and then the sign bit in eflags will indicate the resulting state
of the unrelated bit #7.
So by moving the PageWaiters bit up to bit #7, we can atomically clear
the lock bit and test the waiters bit on x86 too. And architectures
with LL/SC (which is all the usual RISC suspects), the particular bit
doesn't matter, so they are fine with this approach too.
This avoids the extra access to the same atomic word, and thus avoids
the costly stall at page unlock time.
The only downside is that the interface ends up being a bit odd and
specialized: clear a bit in a byte, and test the sign bit. Nick doesn't
love the resulting name of the new primitive, but I'd rather make the
name be descriptive and very clear about the limitation imposed by
trying to work across all relevant architectures than make it be some
generic thing that doesn't make the odd semantics explicit.
So this introduces the new architecture primitive
clear_bit_unlock_is_negative_byte();
and adds the trivial implementation for x86. We have a generic
non-optimized fallback (that just does a "clear_bit()"+"test_bit(7)"
combination) which can be overridden by any architecture that can do
better. According to Nick, Power has the same hickup x86 has, for
example, but some other architectures may not even care.
All these optimizations mean that my page locking stress-test (which is
just executing a lot of small short-lived shell scripts: "make test" in
the git source tree) no longer makes our page locking look horribly bad.
Before all these optimizations, just the unlock_page() costs were just
over 3% of all CPU overhead on "make test". After this, it's down to
0.66%, so just a quarter of the cost it used to be.
(The difference on NUMA is bigger, but there this micro-optimization is
likely less noticeable, since the big issue on NUMA was not the accesses
to 'struct page', but the waitqueue accesses that were already removed
by Nick's earlier commit).
Acked-by: Nick Piggin <npiggin@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Bob Peterson <rpeterso@redhat.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Andrew Lutomirski <luto@kernel.org> Cc: Andreas Gruenbacher <agruenba@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Florian Fainelli [Wed, 28 Dec 2016 23:44:41 +0000 (15:44 -0800)]
net: stmmac: Fix error path after register_netdev move
Commit 5701659004d6 ("net: stmmac: Fix race between stmmac_drv_probe and
stmmac_open") re-ordered how the MDIO bus registration and the network
device are registered, but missed to unwind the MDIO bus registration in
case we fail to register the network device.
Fixes: 5701659004d6 ("net: stmmac: Fix race between stmmac_drv_probe and stmmac_open") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zheng Li [Wed, 28 Dec 2016 15:23:46 +0000 (23:23 +0800)]
ipv6: Should use consistent conditional judgement for ip6 fragment between __ip6_append_data and ip6_finish_output
There is an inconsistent conditional judgement between __ip6_append_data
and ip6_finish_output functions, the variable length in __ip6_append_data
just include the length of application's payload and udp6 header, don't
include the length of ipv6 header, but in ip6_finish_output use
(skb->len > ip6_skb_dst_mtu(skb)) as judgement, and skb->len include the
length of ipv6 header.
That causes some particular application's udp6 payloads whose length are
between (MTU - IPv6 Header) and MTU were fragmented by ip6_fragment even
though the rst->dev support UFO feature.
Add the length of ipv6 header to length in __ip6_append_data to keep
consistent conditional judgement as ip6_finish_output for ip6 fragment.
Signed-off-by: Zheng Li <james.z.li@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: atm: Fix warnings in net/atm/lec.c when !CONFIG_PROC_FS
This patch fixes the following warnings when CONFIG_PROC_FS is not set:
linux/net/atm/lec.c: In function ‘lane_module_cleanup’:
linux/net/atm/lec.c:1062:27: error: ‘atm_proc_root’ undeclared (first
use in this function)
remove_proc_entry("lec", atm_proc_root);
^
linux/net/atm/lec.c:1062:27: note: each undeclared identifier is
reported only once for each function it appears in
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
for -stable:
net/mlx5: Check FW limitations on log_max_qp before setting it
net/mlx5: Cancel recovery work in remove flow
net/mlx5: Avoid shadowing numa_node
net/mlx5: Mask destination mac value in ethtool steering rules
net/mlx5: Prevent setting multicast macs for VFs
net/mlx5e: Don't sync netdev state when not registered
net/mlx5e: Disable netdev after close
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Wed, 28 Dec 2016 12:58:42 +0000 (14:58 +0200)]
net/mlx5e: Disable netdev after close
Disable netdev should come after it was closed, although no harm of doing it
before -hence the MLX5E_STATE_DESTROYING bit- but it is more natural this way.
Fixes: 26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Wed, 28 Dec 2016 12:58:41 +0000 (14:58 +0200)]
net/mlx5e: Don't sync netdev state when not registered
Skip setting netdev vxlan ports and netdev rx_mode on driver load
when netdev is not yet registered.
Synchronizing with netdev state is needed only on reset flow where the
netdev remains registered for the whole reset period.
This also fixes an access before initialization of net_device.addr_list_lock
- which for some reason initialized on register_netdev - where we queued
set_rx_mode work on driver load before netdev registration.
Fixes: 26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huy Nguyen [Wed, 28 Dec 2016 12:58:40 +0000 (14:58 +0200)]
net/mlx5e: Check ets capability before initializing ets settings
During the initial setup, the ets command is sent to firmware
without checking if the HCA supports ets. This causes the invalid
command error. Add the ets capiblity check before sending firmware
command to initialize ets settings.
Fixes: e207b7e99176 ("net/mlx5e: ConnectX-4 firmware support for DCBX") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Wed, 28 Dec 2016 12:58:38 +0000 (14:58 +0200)]
Revert "net/mlx5e: Expose PCIe statistics to ethtool"
This reverts commit 9c7262399ba12825f3ca4b00a76d8d5e77c720f5.
PCIe counters were introduced in a new firmware version, as a result users
with old firmware encountered a syndrome every 200ms due to update stats
work. This feature will be re-introduced later with appropriate capabilities
infrastructure.
Fixes: 9c7262399ba1 ("net/mlx5e: Expose PCIe statistics to ethtool") Signed-off-by: Gal Pressman <galp@mellanox.com> Reported-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Wed, 28 Dec 2016 12:58:36 +0000 (14:58 +0200)]
net/mlx5: Release FTE lock in error flow
Release the FTE lock when adding rule to the FTE has failed.
Fixes: 0fd758d6112f ('net/mlx5: Don't unlock fte while still using it') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Wed, 28 Dec 2016 12:58:35 +0000 (14:58 +0200)]
net/mlx5: Mask destination mac value in ethtool steering rules
We need to mask the destination mac value with the destination mac
mask when adding steering rule via ethtool.
Fixes: 1174fce8d1410 ('net/mlx5e: Support l3/l4 flow type specs in ethtool flow steering') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Wed, 28 Dec 2016 12:58:34 +0000 (14:58 +0200)]
net/mlx5: Avoid shadowing numa_node
Avoid using a local variable named numa_node to avoid shadowing a public
one.
Fixes: db058a186f98 ('net/mlx5_core: Set irq affinity hints') Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Jurgens [Wed, 28 Dec 2016 12:58:33 +0000 (14:58 +0200)]
net/mlx5: Cancel recovery work in remove flow
If there is pending delayed work for health recovery it must be canceled
if the device is being unloaded.
Fixes: 05ac2c0b7438 ("net/mlx5: Fix race between PCI error handlers and health work") Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log