Subhash Jadavani reported this partial backtrace:
Now consider this call stack from MMC block driver (this is on the ARMv7
based board):
[<c001b50c>] (v7_dma_inv_range+0x30/0x48) from [<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c)
[<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c) from [<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c)
[<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c) from [<c0017ff8>] (dma_map_sg+0x3c/0x114)
This is caused by incrementing the struct page pointer, and running off
the end of the sparsemem page array. Fix this by incrementing by pfn
instead, and convert the pfn to a struct page.
Suggested-by: James Bottomley <JBottomley@Parallels.com> Tested-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preempt case current arch_local_irq_restore() from
preempt_schedule_irq() may enable hard interrupt but we really
should disable interrupts when we return from the interrupt,
and so that we don't get interrupted after loading SRR0/1.
When it goes to error through line 144, the memory allocated to *devname is
not freed, and the caller doesn't free it either in line 250. So we free the
memroy of *devname in function cifs_compose_mount_options() when it goes to
error.
Signed-off-by: Cong Ding <dinggnu@gmail.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flag parameter is added in the cyclic transfer request.
Use the flag option of:
- DMA_PREP_INTERRUPT for enabling interrupt.
- DMA_CTRL_ACK for deciding whether ack is requred or not for
descriptor.
ioat does DMA memory sync with DMA_TO_DEVICE direction on a buffer allocated
for DMA_FROM_DEVICE dma, resulting in the following warning from dma debug.
Fixed the dma_sync_single_for_device() call to use the correct direction.
The 'intel_idle_probe' probes the CPU and sets the CPU notifier.
But if later on during the module initialization we fail (say
in cpuidle_register_driver), we stop loading, but we neglect
to unregister the CPU notifier. This means that during CPU
hotplug events the system will fail:
calling intel_idle_init+0x0/0x326 @ 1
intel_idle: MWAIT substates: 0x1120
intel_idle: v0.4 model 0x2A
intel_idle: lapic_timer_reliable_states 0xffffffff
intel_idle: intel_idle yielding to none
initcall intel_idle_init+0x0/0x326 returned -19 after 14 usecs
... some time later, offlining and onlining a CPU:
This patch fixes that by moving the CPU notifier registration
as the last item to be done by the module.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cmd_err is used to handle error code, so it should not be unsigned.
This fixes the following warning when building with W=1 option:
drivers/i2c/busses/i2c-mxs.c: In function 'mxs_i2c_xfer_msg':
drivers/i2c/busses/i2c-mxs.c:331:19: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To fix incorrect P-state frequencies which can happen on
some AMD systems f594065faf4f9067c2283a34619fc0714e79a98d
"ACPI: Add fixups for AMD P-state figures"
introduced a quirk to obtain the correct values by reading
from AMD specific MSRs.
This did cause a regression when running a kernel using that
quirk under Xen which does (currently) not pass through MSR
reads to the HW. Instead the guest gets a 0 in return.
And this seems to cause a failure to initialize the ondemand
governour (hard to say for sure as all P-states appear to run
at the same frequency).
While this should also be fixed in the hypervisor (to allow
a guest to read that MSR), this patch is intended to work
around the issue in the meantime. In discussion it turned out
that indeed real HW/BIOSes may choose to not set the valid bit
and thus mark the P-state as invalid. So this could be considered
a fix for broken BIOSes that also works around the issue on Xen.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
acpi_processor_get_power_info() has to be called before
acpi_processor_setup_cpuidle_states() to have the latest
information available. This fixes the missing C-state information
after AC-->DC transition.
Signed-off-by: Thomas Schlichter <thomas.schlichter@web.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(in acpi_processor_power_init) and never sets the per_cpu idle
device. So when acpi_processor_hotplug on CPU online notification
tries to reference said device it crashes:
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The acpi core will call request_module("acpi-cpufreq") on subsystem init,
but this will fail if the module isn't available at that stage of boot.
Add some module aliases to ensure that udev can load the module on Intel
and AMD systems with the appropriate feature bits - I /think/ that this
will also work on VIA systems, but haven't verified that.
References: http://lkml.kernel.org/r/1448223.sdUJnNSRz4@vostro.rjw.lan Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com> Tested-by: Leonid Isaev <lisaev@umail.iu.edu> Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas reports in https://bugzilla.kernel.org/show_bug.cgi?id=51741
that with his Gentoo config, acpi-cpufreq wasn't enabled and
powernow-k8 couldn't handoff properly to acpi-cpufreq leading to
running without P-state support (i.e., cores are constantly in P0).
To alleaviate that, we need to make powernow-k8 depend on acpi-cpufreq
so that acpi-cpufreq is always present.
References: https://bugzilla.kernel.org/show_bug.cgi?id=51741 Reported-by: Andreas <linuxuser330250@gmx.net> Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1fb9341ac348 ("module: put modules in list much earlier") moved
some of the module initialization code around, and in the process
changed the exit paths too. But for the duplicate export symbol error
case the change made the ddebug_cleanup path jump to after the module
mutex unlock, even though it happens with the mutex held.
Rusty has some patches to split this function up into some helper
functions, hopefully the mess of complex goto targets will go away
eventually.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prarit's excellent bug report:
> In recent Fedora releases (F17 & F18) some users have reported seeing
> messages similar to
>
> [ 15.478160] kvm: Could not allocate 304 bytes percpu data
> [ 15.478174] PERCPU: allocation failed, size=304 align=32, alloc from
> reserved chunk failed
>
> during system boot. In some cases, users have also reported seeing this
> message along with a failed load of other modules.
>
> What is happening is systemd is loading an instance of the kvm module for
> each cpu found (see commit e9bda3b). When the module load occurs the kernel
> currently allocates the modules percpu data area prior to checking to see
> if the module is already loaded or is in the process of being loaded. If
> the module is already loaded, or finishes load, the module loading code
> releases the current instance's module's percpu data.
Now we have a new state MODULE_STATE_UNFORMED, we can insert the
module into the list (and thus guarantee its uniqueness) before we
allocate the per-cpu region.
From SMBIOS 2.6 on, spec use little-endian encoding for UUID other than
network byte order.
So we need to get dmi version to distinguish. If version is 0.0, the
real version is taken from the SMBIOS version. This is part of original
kernel comment in code.
scsi_register_driver will register a prep_fn() function, which
in turn migh need to use the sd_cdp_pool for DIF.
Which hasn't been initialised at this point, leading to
a crash. So reshuffle the init_sd() and exit_sd() paths
to have the driver registered last.
Signed-off-by: Joel D. Diaz <joeldiaz@us.ibm.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Cc: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARNING: vmlinux.o(.text+0x1e709c): Section mismatch in reference from the funct
ion dma_controller_create() to the function .init.text:cppi_controller_start()
The function dma_controller_create() references
the function __init cppi_controller_start().
This is often because dma_controller_create lacks a __init
annotation or the annotation of cppi_controller_start is wrong.
This warning is there due to the deficiency in the commit 07a67bbb (usb: musb:
Make dma_controller_create __devinit).
Since the start() method is only called from musb_init_controller() which is
not annotated, drop '__init' annotation from cppi_controller_start() and also
cppi_pool_init() since it gets called from that function, to avoid another
section mismatch warning...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing braces around an if block in ffs_fs_parse_opts. This broke
parsing the uid/gid mount options and causes mount to fail when using
uid/gid. This has been introduced by commit b9b73f7c (userns: Convert usb
functionfs to use kuid/kgid where appropriate) in 3.7.
Signed-off-by: Benoit Goby <benoit@android.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1644) fixes a race that occurs during startup in
uhci-hcd. If the IRQ line is shared with other devices, it's possible
for the handler routine to be called before the data structures are
fully initialized.
The problem is fixed by adding a check to the IRQ handler routine. If
the initialization hasn't finished yet, the routine will return
immediately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Don Zickus <dzickus@redhat.com> Tested-by: "Huang, Adrian (ISS Linux TW)" <adrian.huang@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the USB ID for the Kinect for Windows RGB camera so it can be used
with the gspca_kinect driver.
Signed-off-by: Jacob Schloss <jacob.schloss@unlimitedautomata.com> Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason is that it broke TI WiLink shared transport on Panda.
Also, callback functions should not be added to board files anymore,
so revert to implementing the power functions in the driver itself.
Additionally, changed a variable name ('status' to 'err') so that this
revert compiles properly.
Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
[changed "err" back to "status" to get it to build in 3.7 - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we have an SHPC-capable bridge with a second SHPC-capable bridge
below it, pushing the upstream bridge's attention button causes a
deadlock.
The deadlock happens because we use the shpchp_wq workqueue to run
shpchp_pushbutton_thread(), which uses shpchp_disable_slot() to remove
devices below the upstream bridge. When we remove the downstream bridge,
we call shpc_remove(), the shpchp driver's .remove() method. That calls
flush_workqueue(shpchp_wq), which deadlocks because the
shpchp_pushbutton_thread() work item is still running.
This patch avoids the deadlock by creating a workqueue for every slot
and removing the single shared workqueue.
Use non-ordered workqueue for attention button events.
Attention button events on each slot can be handled asynchronously. So
we should use non-ordered workqueue. This patch also removes ordered
workqueue in shpchp as a result.
486b10b9f4 ("PCI: pciehp: Handle push button event asynchronously") made
the same change to pciehp. I split this out from a patch by Yijing Wang
<wangyijing@huawei.com> so we fix one thing at a time and to make the
shpchp history correspond more closely with the pciehp history.
When we have a hotplug-capable PCIe port with a second hotplug-capable
PCIe port below it, removing the device below the upstream port causes
a deadlock.
The deadlock happens because we use the pciehp_wq workqueue to run
pciehp_power_thread(), which uses pciehp_disable_slot() to remove devices
below the upstream port. When we remove the downstream PCIe port, we call
pciehp_remove(), the pciehp driver's .remove() method. That calls
flush_workqueue(pciehp_wq), which deadlocks because the
pciehp_power_thread() work item is still running.
This patch avoids the deadlock by creating a workqueue for every PCIe port
and removing the single shared workqueue.
Right now using pcie_aspm=force will not enable ASPM if the FADT indicates
ASPM is unsupported. However, the semantics of force should probably allow
for this, especially as they did before 3c076351c4 ("PCI: Rework ASPM
disable code")
This patch just skips the clearing of any ASPM setup that the firmware has
carried out on this bus if pcie_aspm=force is being used.
Reference: http://bugs.launchpad.net/bugs/962038 Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function aer_recover_queue() calls pci_get_domain_bus_and_slot(), which
requires that the caller decrement the reference count with pci_dev_put().
This patch adds the missing call to pci_dev_put().
The kernel's internal definition of ELF_NGREG uses struct pt_regs, which
means that we disagree with userspace on the size of coredumps since
glibc correctly uses the user-visible struct user_pt_regs.
This patch fixes our ELF_NGREG definition to use struct user_pt_regs
and introduces our own ELF_CORE_COPY_REGS to convert between the user
and kernel structure definitions.
By popular demand, arch/aarch64 is now known as arch/arm64. However,
uname -m (and indeed the GNU triplet) still use aarch64 as the machine
string.
This patch fixes native builds of both the kernel and perf tools by
updating the relevant Makefiles to munge the output of uname -m and
set the ARCH variable appropriately.
putreg() assumes that the tracee is not running and pt_regs_access() can
safely play with its stack. However a killed tracee can return from
ptrace_stop() to the low-level asm code and do RESTORE_REST, this means
that debugger can actually read/modify the kernel stack until the tracee
does SAVE_REST again.
set_task_blockstep() can race with SIGKILL too and in some sense this
race is even worse, the very fact the tracee can be woken up breaks the
logic.
As Linus suggested we can clear TASK_WAKEKILL around the arch_ptrace()
call, this ensures that nobody can ever wakeup the tracee while the
debugger looks at it. Not only this fixes the mentioned problems, we
can do some cleanups/simplifications in arch_ptrace() paths.
Probably ptrace_unfreeze_traced() needs more callers, for example it
makes sense to make the tracee killable for oom-killer before
access_process_vm().
While at it, add the comment into may_ptrace_stop() to explain why
ptrace_stop() still can't rely on SIGKILL and signal_pending_state().
signal_wake_up(resume => true) is overused. None of ptrace/jctl callers
actually want to wakeup a TASK_WAKEKILL task, but they can't specify the
necessary mask.
Turn signal_wake_up() into signal_wake_up_state(state), reintroduce
signal_wake_up() as a trivial helper, and add ptrace_signal_wake_up()
which adds __TASK_TRACED.
This way ptrace_signal_wake_up() can work "inside" ptrace_request()
even if the tracee doesn't have the TASK_WAKEKILL bit set.
Commit 20b279 breaks compatiblity with older perf binaries when run with
precise modifier (:p or :pp) by requiring the exclude_guest attribute to be
set. Older binaries default exclude_guest to 0 (ie., wanting guest-based
samples) unless host only profiling is requested (:H modifier). The workaround
for older binaries is to add H to the modifier list (e.g., -e cycles:ppH -
toggles exclude_guest to 1). This was deemed unacceptable by Linus:
https://lkml.org/lkml/2012/12/12/570
Between family in town and the fresh snow in Breckenridge there is no time left
to be working on the proper fix for this over the holidays. In the New Year I
have more pressing problems to resolve -- like some memory leaks in perf which
are proving to be elusive -- although the aforementioned snow is probably why
they are proving to be elusive. Either way I do not have any spare time to work
on this and from the time I have managed to spend on it the solution is more
difficult than just moving to a new exclude_guest flag (does not work) or
flipping the logic to include_guest (which is not as trivial as one would
think).
So, two options: silently force exclude_guest on as suggested by Gleb which
means no impact to older perf binaries or revert the original patch which
caused the breakage.
This patch does the latter -- reverts the original patch that introduced the
regression. The problem can be revisited in the future as time allows.
Signed-off-by: David Ahern <dsahern@gmail.com> Cc: Avi Kivity <avi@redhat.com> Cc: Gleb Natapov <gleb@redhat.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Robert Richter <robert.richter@amd.com> Link: http://lkml.kernel.org/r/1356749767-17322-1-git-send-email-dsahern@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A read from a range hidden from the user (ex. MSI-X vector table)
attempts to fill the user buffer up to the end of the excluded range
instead of up to the requested count. Fix it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 083b804c4d3e ("async: use workqueue for worker pool") made it
possible that async jobs are moved from pending to running out-of-order.
While pending async jobs will be queued and dispatched for execution in
the same order, nothing guarantees they'll enter "1) move self to the
running queue" of async_run_entry_fn() in the same order.
Before the conversion, async implemented its own worker pool. An async
worker, upon being woken up, fetches the first item from the pending
list, which kept the executing lists sorted. The conversion to
workqueue was done by adding work_struct to each async_entry and async
just schedules the work item. The queueing and dispatching of such work
items are still in order but now each worker thread is associated with a
specific async_entry and moves that specific async_entry to the
executing list. So, depending on which worker reaches that point
earlier, which is non-deterministic, we may end up moving an async_entry
with larger cookie before one with smaller one.
This broke __lowest_in_progress(). running->domain may not be properly
sorted and is not guaranteed to contain lower cookies than pending list
when not empty. Fix it by ensuring sort-inserting to the running list
and always looking at both pending and running when trying to determine
the lowest cookie.
Over time, the async synchronization implementation became quite messy.
We better restructure it such that each async_entry is linked to two
lists - one global and one per domain - and not move it when execution
starts. There's no reason to distinguish pending and running. They
behave the same for synchronization purposes.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a file system is mounted on a virtio-blk disk, we then remove it
and then reattach it, the reattached disk gets the same disk name and
ids as the hot removed one.
This leads to very nasty effects - mostly rendering the newly attached
device completely unusable.
Trying what happens when I do the same thing with a USB device, I saw
that the sd node simply doesn't get free'd when a device gets forcefully
removed.
Imitate the same behavior for vd devices. This way broken vd devices
simply are never free'd and newly attached ones keep working just fine.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If some other kernel subsystem has a module notifier, and adds a kprobe
to a ftrace mcount point (now that kprobes work on ftrace points),
when the ftrace notifier runs it will fail and disable ftrace, as well
as kprobes that are attached to ftrace points.
A kprobe was added to the init_once() function in the fat module on load.
But this happened before ftrace could have touched the code. As ftrace
didn't run yet, the kprobe system had no idea it was a ftrace point and
simply added a breakpoint to the code (0xcc in the cc:bb:d2:4b:e1).
Then when ftrace went to modify the location from a call to mcount/fentry
into a nop, it didn't see a call op, but instead it saw the breakpoint op
and not knowing what to do with it, ftrace shut itself down.
The solution is to simply give the ftrace module notifier the max priority.
This should have been done regardless, as the core code ftrace modification
also happens very early on in boot up. This makes the module modification
closer to core modification.
NCQ capability was used to check availability of SATA Settings page
from Identify Device Data Log, which contains DevSlp timing variables.
It does not work on some HDDs and leads to error messages.
IDENTIFY word 78 bit 5(Hardware Feature Control) can't work either
because it is only the sufficient condition of Identify Device data
log, not the necessary condition.
This patch replaced ata_device->sata_settings with ->devslp_timing
to only save DevSlp timing variables(8 bytes), instead of the whole
SATA Settings page(512 bytes).
In the slow path, we are forced to copy the relocations prior to
acquiring the struct mutex in order to handle pagefaults. We forgo
copying the new offsets back into the relocation entries in order to
prevent a recursive locking bug should we trigger a pagefault whilst
holding the mutex for the reservations of the execbuffer. Therefore, we
need to reset the presumed_offsets just in case the objects are rebound
back into their old locations after relocating for this exexbuffer - if
that were to happen we would assume the relocations were valid and leave
the actual pointers to the kernels dangling, instant hang.
drm/i915: Handle pagefaults in execbuffer user relocations
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55984 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@fwll.ch> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit d6b2123802d "make sure that we always have a return path from
kernel_execve()" reshuffled kernel_init()/init_post() to ensure that
kernel_execve() has a caller to return to.
It removed __init annotation for kernel_init() and introduced/calls a
new routine kernel_init_freeable(). Latter however is inlined by any
reasonable compiler (ARC gcc 4.4 in this case), causing slight code
bloat.
This patch forces kernel_init_freeable() as noinline reducing the .text
bloat-o-meter vmlinux vmlinux_new
add/remove: 1/0 grow/shrink: 0/1 up/down: 374/-334 (40)
function old new delta
kernel_init_freeable - 374 +374 (.init.text)
kernel_init 628 294 -334 (.text)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Barry Davis <Barry-Davis@stormagic.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bbb63c514a3464342967237a51a21ea8f61ab951 (drivers:tty:fix up
ENOIOCTLCMD error handling) changed the default return value from tty
ioctl to be ENOTTY and not EINVAL. This is appropriate.
But in case of TIOCGPTN for the old BSD ptys glibc started failing
because it expects EINVAL to be returned. Only then it continues to
obtain the pts name the other way around.
So fix this case by explicit return of EINVAL in this case.
With the patch "serial: mxs-auart: fix the wrong RTS hardware flow control" the
mainline mxs-uart driver now sets RTSEN only when hardware flow control is
enabled via software. It is not possible any longer to set RTS manually via
software. However, the manual modification is a valid operation.
Regain the possibility to set RTS via software and only set RTSEN when hardware
flow control is explicitly enabled via settermios cflag CRTSCTS.
vt6656 has several headers that use the #pragma pack(1) directive to
enable structure packing, but never disable it. The layout of
structures defined in other headers can then depend on which order the
various headers are included in, breaking the One Definition Rule.
In practice this resulted in crashes on x86_64 until the order of header
inclusion was changed for some files in commit 11d404cb56ecd ('staging:
vt6656: fix headers and add cfg80211.'). But we need a proper fix that
won't be affected by future changes to the order of inclusion.
This removes the #pragma pack(1) directives and adds __packed to the
structure definitions for which packing appears to have been intended.
Commit 2e254212 broke listing of available network names, since it
clamped the length of the returned SSID to WLAN_BSSID_LEN (6) instead of
WLAN_SSID_MAXLEN (32).
Add support for the UART device present in Broadcom TruManage capable
NetXtreme chips (ie: 5761m 5762, and 5725).
This implementation has a hidden transmit FIFO, so running in single-byte
interrupt mode results in too many interrupts. The UART_CAP_HFIFO
capability was added to track this. It continues to reload the THR as long
as the THRE and TSRE bits are set in the LSR up to a specified limit (1024
is used here).
Signed-off-by: Stephen Hurd <shurd@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, function of_clk_get() returns ERR_PTR()
and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
When shut down SPI port, it's possible that MRDY has been asserted and a SPI
timer was activated waiting for SRDY assert, in the case, it needs to delete
this timer.
There has been an error on the xen_failsafe_callback path for failed
iret, which causes the stack pointer to be wrong when entering the
iret_exc error path. This can result in the kernel crashing.
In the classic kernel case, the relevant code looked a little like:
popl %eax # Error code from hypervisor
jz 5f
addl $16,%esp
jmp iret_exc # Hypervisor said iret fault
5: addl $16,%esp
# Hypervisor said segment selector fault
Here, there are two identical addls on either option of a branch which
appears to have been optimised by hoisting it above the jz, and
converting it to an lea, which leaves the flags register unaffected.
In the PVOPS case, the code looks like:
popl_cfi %eax # Error from the hypervisor
lea 16(%esp),%esp # Add $16 before choosing fault path
CFI_ADJUST_CFA_OFFSET -16
jz 5f
addl $16,%esp # Incorrectly adjust %esp again
jmp iret_exc
It is possible unprivileged userspace applications to cause this
behaviour, for example by loading an LDT code selector, then changing
the code selector to be not-present. At this point, there is a race
condition where it is possible for the hypervisor to return back to
userspace from an interrupt, fault on its own iret, and inject a
failsafe_callback into the kernel.
This bug has been present since the introduction of Xen PVOPS support
in commit 5ead97c84 (xen: Core Xen implementation), in 2.6.23.
Signed-off-by: Frediano Ziglio <frediano.ziglio@citrix.com> Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 85ff6acb075a484780b3d763fdf41596d8fc0970 (xen/granttable: Grant
tables V2 implementation) changed the GREFS_PER_GRANT_FRAME macro from
a constant to a conditional expression. The expression depends on
grant_table_version being appropriately set. Unfortunately, at init
time grant_table_version will be 0. The GREFS_PER_GRANT_FRAME
conditional expression checks for "grant_table_version == 1", and
therefore returns the number of grant references per frame for v2.
This causes gnttab_init() to allocate fewer pages for gnttab_list, as
a frame can old half the number of v2 entries than v1 entries. After
gnttab_resume() is called, grant_table_version is appropriately
set. nr_init_grefs will then be miscalculated and gnttab_free_count
will hold a value larger than the actual number of free gref entries.
If a guest is heavily utilizing improperly initialized v1 grant
tables, memory corruption can occur. One common manifestation is
corruption of the vmalloc list, resulting in a poisoned pointer
derefrence when accessing /proc/meminfo or /proc/vmallocinfo:
[ 40.770064] BUG: unable to handle kernel paging request at 0000200200001407
[ 40.770083] IP: [<ffffffff811a6fb0>] get_vmalloc_info+0x70/0x110
[ 40.770102] PGD 0
[ 40.770107] Oops: 0000 [#1] SMP
[ 40.770114] CPU 10
This patch introduces a static variable, grefs_per_grant_frame, to
cache the calculated value. gnttab_init() now calls
gnttab_request_version() early so that grant_table_version and
grefs_per_grant_frame can be appropriately set. A few BUG_ON()s have
been added to prevent this type of bug from reoccurring in the future.
Signed-off-by: Matt Wilson <msw@amazon.com> Reviewed-and-Tested-by: Steven Noonan <snoonan@amazon.com> Acked-by: Ian Campbell <Ian.Campbell@citrix.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Annie Li <annie.li@oracle.com> Cc: xen-devel@lists.xen.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During MSI-X setup the system might run out of vectors. If this happens the
already assigned vectors for this NIC should be freed before trying the
disable MSI-X. Failing to do so results in the following oops.
This patch is to prevent non-USB devices that have RMRRs associated with them from
being placed into the SI Domain during init. This fixes the issue where the RMRR info
for devices being placed in and out of the SI Domain gets lost.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com> Tested-by: Shuah Khan <shuah.khan@hp.com> Reviewed-by: Donald Dutile <ddutile@redhat.com> Reviewed-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Joerg Roedel <joro@8bytes.org> Cc: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds [dev,lun]_link_magic value assignment + checks within generic
target_fabric_port_link() and target_fabric_mappedlun_link() code to ensure
destination config_item *target_item sent from configfs_symlink() ->
config_item_operations->allow_link() is the underlying se_device->dev_group
and se_lun->lun_group that we expect to symlink.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A patch in the 3.2 kernel caused regression with hotplugging the
M-Audio Fast track pro, or sound after suspend. I don't have the
device so I haven't done a full analysis, but it seems userspace
(both udev and pulseaudio) got confused when a card was created,
immediately destroyed, and then created again.
However, at least one person in the bug report (martin djfun)
reports that this patch resolves the issue for him. It also leaves
a message in the log:
"snd-usb-audio: probe of 1-1.1:1.1 failed with error -5" which is
a bit misleading. It is better than non-working audio, but maybe
there's a more elegant solution?
BugLink: https://bugs.launchpad.net/bugs/1095315 Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SNB graphics devices have a bug that prevent them from accessing certain
memory ranges, namely anything below 1M and in the pages listed in the
table. So reserve those at boot if set detect a SNB gfx device on the
CPU to avoid GPU hangs.
Stephane Marchesin had a similar patch to the page allocator awhile
back, but rather than reserving pages up front, it leaked them at
allocation time.
[ hpa: made a number of stylistic changes, marked arrays as static
const, and made less verbose; use "memblock=debug" for full
verbosity. ]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Converting a 64 Bit TOD format value to nanoseconds means that the value
must be divided by 4.096. In order to achieve that we multiply with 125
and divide by 512.
When used within sched_clock() this triggers an overflow after appr.
417 days. Resulting in a sched_clock() return value that is much smaller
than previously and therefore may cause all sort of weird things in
subsystems that rely on a monotonic sched_clock() behaviour.
To fix this implement a tod_to_ns() helper function which converts TOD
values without overflow and call this function from both places that
open coded the conversion: sched_clock() and kvm_s390_handle_wait().
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When transport_lookup_tmr_lun() fails and we return a task management
response from target_complete_tmr_failure(), we need to call
transport_cmd_check_stop_to_fabric() to release the last ref to the
cmd after calling se_tfo->queue_tm_rsp(), or else we will never remove
the failed TMR from the session command list (and we'll end up waiting
forever when trying to tear down the session).
(nab: Fix minor compile breakage)
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a backend IO takes a really long then an initiator might abort a
command, and then when it gives up on the abort, send a LUN reset too,
all before we process any of the original command or the abort. (The
abort will wait for the backend IO to complete too)
When the backend IO final completes (or fails), the abort handling
will proceed and queue up a "return aborted status" operation. Then,
while that's still pending, the LUN reset might find the original
command still on the LUN's list of commands and try to return aborted
status again, which leads to a use-after free when the first
se_tfo->queue_status call frees the command and then the second
se_tfo->queue_status call runs.
Fix this by removing a command from the LUN state_list when we first
are about to queue aborted status; we shouldn't do anything
LUN-related after we've started returning status, so this seems like
the correct thing to do.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a regression bug introduced during v3.6.x code with
the following commit to drop transport_add_cmd_to_queue(), which
originally re-set CMD_T_ACTIVE during pending WRITE I/O submission:
target: replace the processing thread with a TMR work queue
The following sequence happens for write commands (or any other
commands with a data out phase):
- The transport calls target_submit_cmd(), which sets CMD_T_ACTIVE in
cmd->transport_state and sets cmd->t_state to TRANSPORT_NEW_CMD.
- Things go on transport_generic_new_cmd(), which notices that the
command needs to transfer data, so it sets cmd->t_state to
TRANSPORT_WRITE_PENDING and calls transport_cmd_check_stop().
- transport_cmd_check_stop() clears CMD_T_ACTIVE in cmd->transport_state
and returns in the normal case.
- Then we continue on to call ->se_tfo->write_pending().
- The data comes back from the initiator, and the transport calls
target_execute_cmd(), which sets cmd->t_state to TRANSPORT_PROCESSING
and calls into the backend to actually write the data.
At this point, the backend might take a long time to complete the
command, since it has to do real IO. If an abort request comes in for
this command at this point, it will not wait for the command to finish
since CMD_T_ACTIVE is not set. Then when the command does finally
finish, we blow up with use-after-free.
Avoid this by setting CMD_T_ACTIVE in target_execute_cmd() so that
transport_wait_for_tasks() waits for the command to finish executing.
This matches the behavior from before commit 1389533ef944 ("target:
remove transport_generic_handle_data"), when data was signaled via
transport_generic_handle_data(), which set CMD_T_ACTIVE because it
called transport_add_cmd_to_queue().
Signed-off-by: Roland Dreier <roland@purestorage.com> Reported-by: Martin Svec <martin.svec@zoner.cz> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear the target role when no target is provided for
the node performing a PRLI.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked by Robert Love <robert.w.love@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When generating a PRLI response to an initiator, clear the
FCP_SPPF_RETRY bit in the response.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked by Robert Love <robert.w.love@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the aux table is properly initialized, even when optional features
are missing. Without this, the FDPIC loader did not work. This was meant to
be included in commit d5ab780305bb6d60a7b5a74f18cf84eb6ad153b1.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When "alsactl restore" is performed on HDMI codecs, it tries to
restore the channel map value since the channel map controls are
writable. But hdmi_chmap_ctl_put() returns -EBADFD when no PCM stream
is assigned yet, and this results in an error message from alsactl.
Although the error is harmless, it's certainly ugly and can be
regarded as a regression.
As a workaround, this patch changes the return code in such a case to
be zero for making others happy. (A slight excuse is: when the chmap
is changed through the proper alsa-lib API, the PCM status is checked
there anyway, so we don't have to be too strict in the kernel side.)
Some broken systems (like HP nc6120) in some cases, usually after LID
close/open, enable VGA plane, making display unusable (black screen on LVDS,
some strange mode on VGA output). We used to disable VGA plane only once at
startup. Now we also check, if VGA plane is still disabled while changing
mode, and fix that if something changed it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57434 Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There seem to be indeed some awkwards machines around, mostly those
without OpRegion support, where the firmware changes the display hw
state behind our backs when closing the lid.
This force-restore logic has been originally introduced in
If client sends cap message that requests new max size during
exporting caps, the exporting MDS will drop the message quietly.
So the client may wait for the reply that updates the max size
forever. call handle_cap_grant() for cap import message can
avoid this issue.
__wake_requests() will enter infinite loop if we use it to wake
requests in the session->s_waiting list. __wake_requests() deletes
requests from the list and __do_request() adds requests back to
the list.
projects / karo-tx-linux.git / log