Arnd Bergmann [Wed, 30 Nov 2016 16:49:17 +0000 (17:49 +0100)]
Merge tag 'arm-soc/for-4.10/soc' of http://github.com/Broadcom/stblinux into next/soc
Merge "Broadcom soc changes for 4.10" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC changes for 4.10, please pull
the following:
- Rafal adds back the abort handler hook on BCM5301x which is required to silence
errors forwared from the PCIe controller that cannot be silenced at the PCIe RC level
* tag 'arm-soc/for-4.10/soc' of http://github.com/Broadcom/stblinux:
ARM: BCM5301X: Add back handler ignoring external imprecise aborts
Arnd Bergmann [Wed, 30 Nov 2016 13:48:30 +0000 (14:48 +0100)]
Merge tag 'davinci-for-v4.10/soc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
Pull "DaVinci SoC updates for v4.10 (part 3)" from Sekhar Nori:
mach-davinci SoC support updates to adjust
USB ohci device name to that used by drivers
and update of various board files to use gpio
descriptor API used by MMC subsystem for card
detect and write-protect detection.
* tag 'davinci-for-v4.10/soc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da830-evm: use gpio descriptor for mmc pins
ARM: davinci: da850-evm: use gpio descriptor for mmc pins
ARM: davinci: hawk: use gpio descriptor for mmc pins
ARM: davinci: da8xx: Fix ohci device name
Axel Haslam [Thu, 24 Nov 2016 15:04:54 +0000 (16:04 +0100)]
ARM: davinci: da830-evm: use gpio descriptor for mmc pins
Currently the mmc driver is polling the gpio to know if the
card was removed.
By using a gpio descriptor instead of the platform callbacks,
the driver will be able to register the gpio using the mmc core
APIs designed for this purpose.
This has the advantage that an irq will be registered, and
polling is no longer needed. Also, a dependency on platform
callbacks is removed for this board.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
[nsekhar@ti.com: minor commit message edit] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Axel Haslam [Thu, 24 Nov 2016 15:04:53 +0000 (16:04 +0100)]
ARM: davinci: da850-evm: use gpio descriptor for mmc pins
Currently the mmc driver is polling the gpio to know if the
card was removed.
By using a gpio descriptor instead of the platform callbacks,
the driver will be able to register the gpio using the mmc core
APIs designed for this purpose.
This has the advantage that an irq will be registered, and
polling is no longer needed. Also, a dependency on platform
callbacks is removed for this board.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
[nsekhar@ti.com: minor commit message edit] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Axel Haslam [Thu, 24 Nov 2016 15:04:52 +0000 (16:04 +0100)]
ARM: davinci: hawk: use gpio descriptor for mmc pins
Currently the mmc driver is polling the gpio to know if the
card was removed.
By using a gpio descriptor instead of the platform callbacks,
the driver will be able to register the gpio using the mmc core
APIs designed for this purpose.
This has the advantage that an irq will be registered, and
polling is no longer needed. Also, a dependency on platform
callbacks is removed for this board.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Arnd Bergmann [Fri, 25 Nov 2016 23:30:46 +0000 (00:30 +0100)]
Merge tag 'oxnas-arm-soc-for-4.10-v2' of https://github.com/OXNAS/linux into next/soc
Pull "ARM: OXNAS SoC updates for 4.10" from Neil Armstrong:
- Add SMP support for the Oxford Semiconductor OX820 SoC
from http://lkml.kernel.org/r/20161021085848.1754-1-narmstrong@baylibre.com
Changes since v1 Pull Request at : http://lkml.kernel.org/r/1305c61f-b1ef-7caf-7788-67e2b907e873@baylibre.com
- Clarify copyright dates in commit message
- Remove linux/arch/... lines from the top of the files
* tag 'oxnas-arm-soc-for-4.10-v2' of https://github.com/OXNAS/linux:
ARM: oxnas: Add OX820 config and makefile entry
ARM: oxnas: Add OX820 SMP support
Axel Haslam [Thu, 3 Nov 2016 16:03:06 +0000 (17:03 +0100)]
ARM: davinci: da8xx: Fix ohci device name
While the clk lookup table is making reference to "ohci"
other subsystems (such as phy) are trying to match "ohci.0"
Since there is a single ohci instance, instead of changing
the clk name, change the dev id to -1, and add the "-da8xx"
postfix to match the driver name that will also be changed
in a subsequent patch.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Neil Armstrong [Fri, 9 Sep 2016 10:23:11 +0000 (12:23 +0200)]
ARM: oxnas: Add OX820 SMP support
The Oxford Semiconductor OX820 is a ARM11MPcore based SoC sharing some
features with the OX810 earlier SoC.
This patch adds the core to wake up the second core.
Clarifications about Copyrights dates :
- hotplug.c was taken from an old versatile code by Ma Haijun and left verbatim
- headsmp.S was taken from an old versatile code and adapted by Ma Haijun
- platsmp.c is a mix from versatile code, Ma Haijun code and my code for DT
Hence the 2002/2003 ARM Coryrights and 2013 Ma Haijun Copyrights.
Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Kevin Hilman [Wed, 16 Nov 2016 16:44:38 +0000 (08:44 -0800)]
ARM: davinci: PM: fix build when da850 not compiled in
Currently, suspend/resume support is only available on da850 platforms,
and the platform PM code has dependencies on da850 functions. However,
CONFIG_SUSPEND might be enabled even when da850 support is not, causing
build failure:
arch/arm/mach-davinci/built-in.o: In function `davinci_pm_init':
pm_domain.c:(.init.text+0x1fb8): undefined reference to `da8xx_get_mem_ctlr'
pm_domain.c:(.init.text+0x20b0): undefined reference to `da8xx_syscfg1_base'
Fix this by only building the PM core when da850 is enabled.
Reported-by: Sekhar Nori <nsekhar@ti.com> Fixes: aa9aa1ec2df6 ("ARM: davinci: PM: rework init, remove platform device") Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Olof Johansson [Sat, 19 Nov 2016 01:51:13 +0000 (17:51 -0800)]
Merge tag 'mvebu-drivers-4.10-1' of git://git.infradead.org/linux-mvebu into next/soc
mvebu drivers for 4.10 (part 1)
Clean-up on thegpio driver for old SoCs(non DT)
* tag 'mvebu-drivers-4.10-1' of git://git.infradead.org/linux-mvebu:
ARM/orion/gpio: Replace three seq_printf() calls by seq_puts() in orion_gpio_dbg_show()
Olof Johansson [Sat, 19 Nov 2016 00:49:09 +0000 (16:49 -0800)]
Merge tag 'omap-for-v4.10/legacy-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Legacy platform_data removal for omaps for v4.10 merge window.
We've dropped the last legacy boot board-*.c files for mach-omap2
for v4.9 so now we can start removing the unused platform_data.
All of the below has been unused since v4.9 merge window:
- Drop legacy pmic init code
- Apply seq_puts() fixes for legacy mux code, then drop it
- Drop legacy serial init
- Drop legacy i2c init
- Drop legacy PM init
- Drop legacy twl4030 platform init
- Drop legacy USB host init
- Drop legacy muxing for tusb6010, n8x0 is still using it's
platform init via pdata-quirks.c
- Drop legacy musb init
- Drop hwmod related legacy mux code
- Drop legacy hwmod data for omap3
- Drop legacy smsc911x and smc91x init
- Drop legacy board flash init
- Drop legacy ads7846 init
- Drop legacy sdram timings
* tag 'omap-for-v4.10/legacy-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: OMAP2+: Drop legacy sdram timings
ARM: OMAP2+: Drop legacy ads7846 init
ARM: OMAP2+: Remove legacy board-flash.c
ARM: OMAP2+: Remove legacy smsc911x and smc91x GPMC support
ARM: OMAP2+: Remove legacy data from hwmod for omap3
ARM: OMAP2+: Remove legacy mux code
ARM: OMAP2+: Remove legacy hwmod mux code
ARM: OMAP2+: Remove legacy usb-musb.c platform init code
ARM: OMAP2+: Remove legacy muxing for usb-tusb6010.c
ARM: OMAP2+: Remove legacy usb-host.c platform init code
ARM: OMAP2+: Remove legacy twl4030 platform init code
ARM: OMAP2+: Remove legacy PM init
ARM: OMAP2+: Remove legacy i2c.c platform init code
ARM: OMAP2+: Remove legacy serial.c
ARM: OMAP2+: mux: Use seq_putc() in omap_mux_dbg_signal_show()
ARM: OMAP2+: mux: Replace three seq_printf() calls by seq_puts()
ARM: OMAP: kill omap_pmic_init
ARM: OMAP2: kill omap2_pmic_init
ARM: OMAP3: kill omap3_pmic_init
ARM: OMAP3: kill omap3_pmic_get_config and twl_{get,set}_voltage
...
Olof Johansson [Sat, 19 Nov 2016 00:42:44 +0000 (16:42 -0800)]
Merge tag 'omap-for-v4.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC changes for omaps for v4.10 merge window:
- Add hwmod interconnect target wrapper module data for crypto
accelerators for am3xxx, am43xx and dra7
- Add support for dra71x family of SoCs
- PM fixes for omap4/5 needed for omap5 cpuidle
* tag 'omap-for-v4.10/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: hwmod: Do not register RTC on DRA71
ARM: OMAP2+: board-generic: add support for DRA71x family
ARM: AMx3xx: hwmod: Add data for RNG
ARM: AM43xx: hwmod: Add data for DES
ARM: OMAP: DRA7xx: Make L4SEC clock domain SWSUP only
ARM: DRA7: hwmod: Add data for RNG IP
ARM: DRA7: hwmod: Add data for SHA IP
ARM: DRA7: hwmod: Add data for AES IP
ARM: DRA7: hwmod: Add data for DES IP
ARM: OMAP5: Add basic cpuidle MPU CSWR support
ARM: OMAP4+: Fix bad fallthrough for cpuidle
ARM: OMAP5: Fix mpuss_early_init
ARM: OMAP5: Fix build for PM code
Olof Johansson [Fri, 18 Nov 2016 18:33:36 +0000 (10:33 -0800)]
Merge tag 'soc-for-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/soc
STM32 SOC updates for v4.10, round 1.
Highlights:
----------
- Add new MCU SOC STM32F746
* tag 'soc-for-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: Kconfig: Introduce MACH_STM32F746 flag
ARM: mach-stm32: Add a new SOC - STM32F746
Olof Johansson [Fri, 18 Nov 2016 17:59:26 +0000 (09:59 -0800)]
Merge tag 'imx-soc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
i.MX SoC changes for 4.10:
- Drop PL310_ERRATA_769419 for Vybrid, as it turns out that the SoC
integrates revision r3p2 of the L2C-310, which is not affected by
errata 769419.
- Support perf for i.MX6 Multi-Mode DDR Controller (MMDC), so that we
can profile memory access performance.
- Support i.MX6ULL SoC using i.MX6UL base, since it's a derivative of
i.MX6UL and pin-to-pin compatible with i.MX6UL.
* tag 'imx-soc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: mach-imx6ul: add imx6ull support
ARM: imx: Drop errata 769419 for Vybrid
ARM: imx: mmdc perf function support i.MX6QP
ARM: imx: Added perf functionality to mmdc driver
Linus Walleij [Wed, 9 Nov 2016 08:12:06 +0000 (09:12 +0100)]
ARM: integrator: drop EBI access use syscon
The EBI lookup is not longer in use: this has been moved to the
NAND chip driver. The syscon node is better accessed indirectly
using the regmap like the NAND chip driver does, so let's use
the syscon to set the modem control signals RTS/CTS through the
dedicated syscon register.
We also migrate the decoder status "SC_DEC" register that
enumerate the logic modules using syscon.
Cc: Russell King <linux@armlinux.org.uk> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 18 Nov 2016 07:15:25 +0000 (23:15 -0800)]
Merge tag 'pxa-for-4.10' of https://github.com/rjarzmik/linux into next/soc
This is the pxa changes for v4.10 cycle.
This cycle is covering :
- some clock fixes common with sa1100 architecture
- the consequence of the pxa_camera conversion to v4l2
- a small irq related fix for pxa25x device-tree only
* tag 'pxa-for-4.10' of https://github.com/rjarzmik/linux:
ARM: pxa: fix pxa25x interrupt init
ARM: pxa: remove duplicated include from spitz.c
ARM: pxa: em-x270: use the new pxa_camera platform_data
ARM: pxa: ezx: use the new pxa_camera platform_data
ARM: pxa: mioa701: use the new pxa_camera platform_data
ARM: pxa: pxa_cplds: honor probe deferral
ARM: sa11x0/pxa: get rid of get_clock_tick_rate
watchdog: sa11x0/pxa: get rid of get_clock_tick_rate
ARM: sa11x0/pxa: acquire timer rate from the clock rate
clk: pxa25x: OSTIMER0 clocks from the main oscillator
Olof Johansson [Fri, 18 Nov 2016 01:41:30 +0000 (17:41 -0800)]
Merge tag 'renesas-soc-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Renesas ARM Based SoC Updates for v4.10
Enhancements:
* Basic support for r8a7743 SoC; only SoC code so far
* Select errata 798181 for SoCs with CA15 cores
Clean-up:
* Consolidate R8A7743 and R8A779[234] machine definitions
Documentation:
* Add Marzen, Gose and Alt board part numbers to DT bindings
* Document SK-RZG1M board
* tag 'renesas-soc-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779/marzen: Add board part number to DT bindings
ARM: shmobile: select errata 798181 for SoCs with CA15 cores
ARM: shmobile: Consolidate R8A7743 and R8A779[234] machine definitions
ARM: shmobile: r8a7793/gose: Add board part number to DT bindings
ARM: shmobile: r8a7794/alt: Add board part number to DT bindings
ARM: shmobile: document SK-RZG1M board
ARM: shmobile: r8a7743: basic SoC support
ARM: shmobile: only call rcar_gen2_clocks_init() if present
ARM: shmobile: Sort Kconfig selections
Rafał Miłecki [Sat, 29 Oct 2016 11:12:29 +0000 (13:12 +0200)]
ARM: BCM5301X: Add back handler ignoring external imprecise aborts
Since early BCM5301X days we got abort handler that was removed by
commit 937b12306ea79 ("ARM: BCM5301X: remove workaround imprecise abort
fault handler"). It assumed we need to deal only with pending aborts
left by the bootloader. Unfortunately this isn't true for BCM5301X.
When probing PCI config space (device enumeration) it is expected to
have master aborts on the PCI bus. Most bridges don't forward (or they
allow disabling it) these errors onto the AXI/AMBA bus but not the
Northstar (BCM5301X) one.
iProc PCIe controller on Northstar seems to be some older one, without
a control register for errors forwarding. It means we need to workaround
this at platform level. All newer platforms are not affected by this
issue.
Remove fake platform device used for PM init. Move pdata values which
are common across all current platforms into pm.c.
Also, since PM is only used on da8xx, remove davinci_pm_init() from
common init code, and only use in da850/omapl138 board files that are
currently creating the fake platform_device.
Suggested-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
[nsekhar@ti.com: subject line adjustment] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Andrey Smirnov [Wed, 9 Nov 2016 16:44:10 +0000 (08:44 -0800)]
ARM: imx: Drop errata 769419 for Vybrid
According to the datasheet, VF610 uses revision r3p2 of the L2C-310
block, same as i.MX6Q+, which does not require a software workaround for
ARM errata 769419.
Tony Lindgren [Thu, 10 Nov 2016 23:07:32 +0000 (16:07 -0700)]
ARM: OMAP2+: Drop legacy sdram timings
These are no longer used. If somebody needs to configure
memory timings for various idle modes, they should be
implemented as a device driver callbacks from the PM
code.
Legacy board files in mach-omap2 used the helper functions
board_{nor,nand,onenand}_init() to initialize the flash
devices attached to the GPMC.
With Device Tree booting the initialization is handled by
the GPMC driver gpmc_probe_*_child() functions so this
code is not needed anymore now that OMAP2+ is DT-only.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: OMAP2+: Remove legacy smsc911x and smc91x GPMC support
When connecting an ethernet chip to the GPMC, such as smc91x
or smsc911x, a GPIO has to be requested to be used as an IRQ
and also the IO memory for a GPMC chip-select.
When booting with DT the chip-select allocation is handled
in a generic manner in the GPMC driver and the GPIO to IRQ
mapping is made by the DT core so this code is not needed
anymore now that mach-omap2 related boards are DT-only.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Fri, 21 Oct 2016 10:02:12 +0000 (03:02 -0700)]
ARM: OMAP2+: Remove legacy data from hwmod for omap3
This data is now coming from device tree so we can remove the
duplicate data. Let's keep the DSS and DMA related things for now
until those have been converted to device tree completely.
While at it, let's also add the trailing commas to data structures
so further processing with scripts will be a bit easier.
Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 17 Oct 2016 07:08:40 +0000 (00:08 -0700)]
ARM: OMAP2+: Remove legacy PM init
This is no longer needed when booted with device tree.
And let's replace cpu_is with soc_is for the PM code to
avoid confusion, they do the same thing.
Note that omap_pmic_late_init() now just calls
omap3_twl_init() and omap4_twl_init() to initialize the
voltage layer so we can remove the remaining references
to twl-common code and remove it in the following patch.
Nishanth Menon [Fri, 21 Oct 2016 10:38:38 +0000 (16:08 +0530)]
ARM: DRA7: hwmod: Do not register RTC on DRA71
RTC is not available on DRA71x, so accessing any of the RTC
register or clkctrl register will lead to a crash. So, do not
register RTC hwmod for DRA71x.
Joel Fernandes [Tue, 18 Oct 2016 07:55:25 +0000 (10:55 +0300)]
ARM: OMAP: DRA7xx: Make L4SEC clock domain SWSUP only
Using HWSUP for l4sec clock domain is causing warnings in HWMOD code for
DRA7. Based on some observations, once the clock domain goes into an IDLE
state (because of no activity etc), the IDLEST for the module goes to '0x2'
value which means Interface IDLE condition. So far so go, however once the
MODULEMODE is set to disabled for the particular IP, the IDLEST for the
module should go to '0x3', per the HW AUTO IDLE protocol. However this is
not observed and there is no reason per the protocl for the transition to
not happen. This could potentially be a bug in the HW AUTO state-machine.
Work around for this is to use SWSUP only for the particular clockdomain.
With this all the transitions of IDLEST happen correctly and warnings
don't occur.
Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Joel Fernandes [Tue, 18 Oct 2016 07:55:24 +0000 (10:55 +0300)]
ARM: DRA7: hwmod: Add data for RNG IP
DRA7 SoC contains hardware random number generator. Add hwmod data for
this IP so that it can be utilized.
Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[t-kristo@ti.com: squashed the RNG hwmod IP flag fixes from Lokesh,
squashed the HS chip fix from Daniel Allred] Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Joel Fernandes [Tue, 18 Oct 2016 07:55:22 +0000 (10:55 +0300)]
ARM: DRA7: hwmod: Add data for AES IP
DRA7 SoC contains AES crypto hardware accelerator. Add hwmod data for
this IP so that it can be utilized by crypto frameworks.
Signed-off-by: Joel Fernandes <joelf@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[t-kristo@ti.com: squash in support for both AES1 and AES2 cores] Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds MPUSS low power states in cpuidle.
C1 - CPU0 WFI + CPU1 WFI + MPU ON
C2 - CPU0 RET + CPU1 RET + MPU CSWR
Modified from TI kernel tree commit 605967fd2205 ("ARM: DRA7: PM:
cpuidle MPU CSWR support") except enable cpuidle for omap5 instead
of dra7.
According to Nishanth Menon <nm@ti.com>, cpuidle on dra7 is not
supported properly in the hardware so we don't want to enable it.
However, for omap5 this adds some nice power savings. Note that
the TI 3.8 based tree has other cpuidle states that we may be able
to enable later on.
On omap5-uevm, the power consumption eventually settles down to about
920mW with ehci-omap and ohci-omap3 unloaded compared to about 1.7W
without these patches. Note that it seems to take few minutes after
booting for the idle power to go down to 920mW from 1.3W, no idea so
far what might be causing that.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[ j-keerthy@ti.com rework on 3.14] Signed-off-by: Keerthy <j-keerthy@ti.com>
[nm@ti.com: updates based on profiling]
[tony@atomide.com: dropped CPUIDLE_FLAG_TIME_VALID no longer used,
changed for omap5 only as requested by Nishanth, updated comments] Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 7 Nov 2016 23:50:11 +0000 (16:50 -0700)]
ARM: OMAP4+: Fix bad fallthrough for cpuidle
We don't want to fall through to a bunch of errors for retention
if PM_OMAP4_CPU_OSWR_DISABLE is not configured for a SoC.
Fixes: 6099dd37c669 ("ARM: OMAP5 / DRA7: Enable CPU RET on suspend") Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 7 Nov 2016 23:50:11 +0000 (16:50 -0700)]
ARM: OMAP5: Fix mpuss_early_init
We need to properly initialize mpuss also on omap5 like we do on omap4.
Otherwise we run into similar kexec problems like we had on omap4 when
trying to kexec from a kernel with PM initialized.
Fixes: 0573b957fc21 ("ARM: OMAP4+: Prevent CPU1 related hang with kexec") Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 7 Nov 2016 23:50:10 +0000 (16:50 -0700)]
ARM: OMAP5: Fix build for PM code
It's CONFIG_SOC_OMAP5, not CONFIG_ARCH_OMAP5. Looks like make randconfig
builds have not hit this one yet.
Fixes: b3bf289c1c45 ("ARM: OMAP2+: Fix build with CONFIG_SMP and CONFIG_PM
is not set") Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
Simon Horman [Mon, 31 Oct 2016 09:52:17 +0000 (10:52 +0100)]
ARM: shmobile: only call rcar_gen2_clocks_init() if present
The RZ/G1M (r8a7743) uses the R-Car Gen2 core, but not the R-Car Gen2 clock
driver. This is a harbinger of a transition for R-Car Gen2 SoCs. As the
process to get all the required pieces in place is somewhat complex it
seems useful to try to disentangle dependencies where possible.
The approach here is to temporarily disable calling rcar_gen2_clocks_init()
if no R-Car Gen2 SoC are configured and thus the symbol will not be
present.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Axel Haslam [Mon, 31 Oct 2016 20:47:21 +0000 (15:47 -0500)]
ARM: davinci: da8xx: register USB PHY clocks in the DT file
The usb20_phy clock needs to be registered for the driver to be able
to get and enable a clock. Currently the usb phy clocks are registered
from board files, which will not be called during a device tree based
boot.
To be able to probe correctly usb form a device tree boot, register
the usb phy clocks from the DT specific init.
Unfortunately, davinci does not have proper clock support on device tree
yet, so by registering the clock from the DT specific file we are
forced to hardcode the parent clock, and cannot select refclkin as
parent for any of the phy clocks of the da850 family.
As none of the current da850 based boards currently in mainline use
refclkin as source. I guess we can live with this limitation until clocks
are correctly represented through CCF/device tree.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
[Added error checking] Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: typo fixes in commit message] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
David Lechner [Mon, 31 Oct 2016 20:47:20 +0000 (15:47 -0500)]
ARM: davinci: da8xx: add usb phy clocks
Up to this point, the USB phy clock configuration was handled manually in
the board files and in the usb drivers. This adds proper clocks so that
the usb drivers can use clk_get and clk_enable and not have to worry about
the details. Also, the related code is removed from the board files and
replaced with the new clock registration functions.
This also removes the #if IS_ENABLED(CONFIG_USB_MUSB_HDRC) around the musb
declaration and renames the musb platform device so that we can reference
it from the usb20 clock even if the musb device is not used.
Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Axel Haslam <ahaslam@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Kbuild descends into arch/arm/mach-mediatek/Makefile only when
CONFIG_ARCH_MEDIATEK is enabled. So, obj-$(CONFIG_ARCH_MEDIATEK)
is always equivalent to obj-y in this Makefile.
David Lechner [Thu, 27 Oct 2016 00:18:15 +0000 (19:18 -0500)]
ARM: davinci: da8xx: Add USB PHY platform device
There is now a proper phy driver for the DA8xx SoC USB PHY. This adds the
platform device declarations needed to use it.
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: keep usb-davinci.h included in board-da830-evm.c
minor subject line adjustment] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Karl Beldan [Wed, 5 Oct 2016 13:05:31 +0000 (15:05 +0200)]
ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for lcdc
This is required for tilcdc to be able to acquire a functional clock
on da850 SoCs.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
[Bartosz:
- added the commit description
- changed the compatible string to 'ti,da850-tilcdc'] Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Axel Haslam [Wed, 26 Oct 2016 19:41:55 +0000 (21:41 +0200)]
ARM: davinci: da8xx: Add full regulator constraints for non-DT boot
The phy framework requests an optional "phy" regulator. If it does
not find one, it returns -EPROBE_DEFER. In the case of non-DT boot
for the omap138-lcdk board, this would prevent the usb11 phy to probe
correctly and ohci would not enumerate.
By calling regulator_has_full_constraints(), An error would be returned
instead of -EPROBE_DEFER for the regulator, and the probe of the phy driver
can continue normally without a regulator.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
[nsekhar@ti.com: minor commit message updates] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The CFGCHIP registers are used by a number of devices, so use a syscon
device to share them. The first consumer of this will be the phy-da8xx-usb
driver.
Add the syscon device and register it.
Signed-off-by: David Lechner <david@lechnology.com>
[nsekhar@ti.com: minor commit message fixes] Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Alexandre Bailon [Thu, 27 Oct 2016 15:32:36 +0000 (17:32 +0200)]
ARM: davinci: da8xx: Remove duplicated defines
Some macro for DA8xx CFGCHIP are defined in usb-davinci.h,
but da8xx-cfgchip.h intend to replace them.
Remove duplicated defines between da8xx-cfgchip.h and usb-davinci.h
Signed-off-by: Alexandre Bailon <abailon@baylibre.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Olof Johansson [Sat, 29 Oct 2016 18:40:52 +0000 (11:40 -0700)]
Merge tag 'vexpress-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/soc
ARMv7 Vexpress fixes for v4.10
Couple of fixes to MCPM/CCI drivers to check and ensure that the kernel
is actually allowed to take control over CCI ports(i.e. running in
secure mode) before enabling MCPM.
This is needed to boot Linux in HYP mode (very useful for development
on virtualization) with CONFIG_MCPM enabled kernel.
* tag 'vexpress-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
drivers: cci: add missing CCI port availability firmware check
ARM: vexpress: refine MCPM smp operations override criteria
projects / karo-tx-linux.git / log