Johannes Berg [Thu, 29 Jul 2010 14:07:51 +0000 (07:07 -0700)]
iwlwifi: refactor iwl_setup_rxon_timing
All callers of iwl_setup_rxon_timing() also send
the command right away, so rename the function
to iwl_send_rxon_timing() and move the sending
into it. Also, some callers clear the data, this
can be done always and thus moved in as well.
Finally, there's no reason for the function to
acquire the spinlock, but it should be called
with the mutex held, so assert that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Update outdated comments of iwl_set_rxon_channel() to reflect the
current signature. Also remove the unnecessary validation of the
channel. Those channel info are constructed in iwlwifi driver
and mac80211 will never modify the content of the struct. Also
everytime before this function is called the channel info has
been validated already (as a paranoid check).
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When iwl_mac_config() is called by mac80211, the channel pointer
hw->conf->channel can potentially change, resulting in mismatch
band and channel number when configuring RXON command. To avoid
this situation, save the channel pointer in local variables
and validate the channel before using it. Note that priv->mutex
is locked during the whole function so the local variables are safe.
Same change is applied to iwl_mac_channel_switch() since basically
it copies code from iwl_mac_config().
Also removed an outdated comment in the flow.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
iwlwifi: do not call ieee80211_frequency_to_channel
A few cases in iwlwifi driver function ieee80211_frequency_to_channel()
is called to get channel number from center frequency. This is not needed
since the channel number is already saved in hw_value field of struct
ieee80211_channel in function iwlcore_init_geos(). So replace those function
calls with hw_value field of struct ieee80211_channel.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Julian Calaby [Tue, 17 Aug 2010 18:52:41 +0000 (14:52 -0400)]
Hostap: Fix "'ret' set but not used" warning message from GCC in hostap
CC [M] drivers/net/wireless/hostap/hostap_ioctl.o
drivers/net/wireless/hostap/hostap_ioctl.c: In function 'prism2_request_scan':
drivers/net/wireless/hostap/hostap_ioctl.c:1666:6: warning: variable 'ret' set but not used
Signed-off-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 6 Aug 2010 19:39:14 +0000 (12:39 -0700)]
iwlwifi: fix thermal throttling related power management operation
The current approach is very broken because it adds an
often-used code path that will not initialise "cmd" at all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Shanyu Zhao <shanyu.zhao.intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 17 Aug 2010 10:08:07 +0000 (12:08 +0200)]
mac80211-hwsim: allow configuring IBSS
It will not look standard-compliant in a sniffer
because because it doesn't
* sync TSF
* adjust the TSF in beacons
* send beacons at TBTT
* cancel beacons when another phy sends
However, it does allow testing the configuration
and parts of the mac80211 code for IBSS and as
such is still useful.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 17 Aug 2010 10:04:34 +0000 (12:04 +0200)]
wireless: move documentation books
This moves mac80211 documentation into a new
802.11 bookset and also adds a cfg80211 book
to the set. All of this is rather incomplete,
but it's easier to work with big code moving
as a separate patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Like other vendors, p54* devices have a checksum for
the EEPROM descriptor data. This patch enhances the
parser code to generate and verify the data fields,
before initializing the radio-chip on the card.
Note:
If you have to bootstrap an alternative EEPROM image
for your device and you don't know how to generate a
valid crc ccitt checksum, you should take a look at:
http://git.kernel.org/?p=linux/kernel/git/chr/p54tools.git
The "checksum" utility loads a binary p54 EEPROM blob
(use the -f switch, to skip the check) and applies
the correct crc automatically.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Sun, 15 Aug 2010 17:03:15 +0000 (13:03 -0400)]
ath5k: don't enable probe request rx for STAs
AR5K_RX_FILTER_PROBEREQ enables reception of probe requests,
but the filter flag FIF_BCN_PRBRESP_PROMISC is actually about
receiving beacons and probe _responses_, so we shouldn't
turn on the filter when scanning.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Sun, 15 Aug 2010 17:03:13 +0000 (13:03 -0400)]
ath5k: remove monitor check in receive_frame_ok filter
Monitor interfaces are never seen by the driver, so tests based on
that opmode don't make sense. Also, we already pass all mic
failure packets.
Consequently this code is actually accepting any frames with just
crypto errors and rejecting those with CRC, FIFO, and PHY errors for
all interface types. Adjust the code and comment accordingly.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 12 Aug 2010 13:38:38 +0000 (15:38 +0200)]
cfg80211/mac80211: extensible frame processing
Allow userspace to register for more than just
action frames by giving the frame subtype, and
make it possible to use this in various modes
as well.
With some tweaks and some added functionality
this will, in the future, also be usable in AP
mode and be able to replace the cooked monitor
interface currently used in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 12 Aug 2010 13:37:29 +0000 (15:37 +0200)]
mac80211: remove unused don't-encrypt flag
When MFP is disabled, action frames will not
be encrypted since they are management frames
and the only management frames that can then
be encrypted are authentication frames.
Therefore, setting the don't-encrypt flag on
action frames is unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 12 Aug 2010 12:49:58 +0000 (14:49 +0200)]
cfg80211: mark ieee80211_hdrlen const
This function analyses only its single, value-passed
argument, and has no side effects. Thus it can be
const, which makes mac80211 smaller, for example:
text data bss dec hex filename
362518 16720 884 380122 5ccda mac80211.ko (before)
362358 16720 884 379962 5cc3a mac80211.ko (after)
a 160 byte saving in text size, and an optimisation
because the function won't be called as often.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/libertas/cfg.c: In function 'lbs_scan_worker':
drivers/net/wireless/libertas/cfg.c:722: error: 'TASK_NORMAL' undeclared (first use in this function)
drivers/net/wireless/libertas/cfg.c:722: error: (Each undeclared identifier is reported only once
drivers/net/wireless/libertas/cfg.c:722: error: for each function it appears in.)
drivers/net/wireless/libertas/cfg.c: In function 'lbs_cfg_connect':
drivers/net/wireless/libertas/cfg.c:1267: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function 'signal_pending'
drivers/net/wireless/libertas/cfg.c:1267: error: implicit declaration of function 'schedule_timeout'
So wait.h has a dependency on sched.h, but doesn't include sched.h. This
patch doesn't fix that.
Cc: Dan Williams <dcbw@redhat.com> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 10 Aug 2010 07:46:40 +0000 (09:46 +0200)]
mac80211: remove unused status flag checks
The decryption code verifies whether or not
a given frame was decrypted and verified by
hardware. This is unnecessary, as the crypto
RX handler already does it long before the
decryption code is even invoked, so remove
that code to avoid confusion.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 10 Aug 2010 07:46:38 +0000 (09:46 +0200)]
mac80211: use cipher suite selectors
Currently, mac80211 translates the cfg80211
cipher suite selectors into ALG_* values.
That isn't all too useful, and some drivers
benefit from the distinction between WEP40
and WEP104 as well. Therefore, convert it
all to use the cipher suite selectors.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Sun, 8 Aug 2010 02:16:30 +0000 (21:16 -0500)]
libertas: [spi] use common firmware request helper and new firmware locations
linux-firmware puts libertas firmware in /libertas. Fix the driver to
look there first, but fall back to the old firmware names if the new
ones don't exist. Add preference for newer firmware versions too.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Sun, 8 Aug 2010 02:15:52 +0000 (21:15 -0500)]
libertas: [sdio] use common firmware request helper and new firmware locations
linux-firmware puts libertas firmware in /libertas. Fix the driver to
look there first, but fall back to the old firmware names if the new
ones don't exist. Add preference for newer firmware versions too.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Sun, 8 Aug 2010 02:15:19 +0000 (21:15 -0500)]
libertas: [cs] use common firmware request helper and new firmware locations
linux-firmware puts libertas firmware in /libertas. Fix the driver to
look there first, but fall back to the old firmware names if the new
ones don't exist.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Sun, 8 Aug 2010 02:14:33 +0000 (21:14 -0500)]
libertas: add two-stage firmware request helper
SDIO, GSPI, and CS all use 2-stage firmware and the loading
process and logic should be the same. Allow module parameters
to override the automatic firmware choice, otherwise just walk
the bus driver's firmware table and pick out the first firmware
pair that exists for the given model.
Some special care is taken to allow overriding of just the helper
or the main firmware, but let the other of the pair be chosen
automatically.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Sun, 8 Aug 2010 02:13:57 +0000 (21:13 -0500)]
libertas: [usb] use new firmware locations
Look for firmware where the linux-firmware tree actually puts it, but
fall back to original firmware name & location when the new location
doesn't exist.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 6 Aug 2010 18:49:27 +0000 (20:49 +0200)]
rt2x00: Remove ieee80211_rx_status from rt2x00_dev
rt2x00 was keeping a copy of ieee80211_rx_status embedded
into the rt2x00_dev structure. For each RX frame, this structure
was copied into the skb->cb where mac80211 would handle it further.
However at the moment only the fields current band, and frequency
were updated. Whereas the band was already provided directly within
the rt2x00_dev structure. Save a memcpy action, and reduce memory
a bit, by adding a curr_freq field to rt2x00_dev, and completely
remove the ieee80211_rx_status structure from rt2x00_dev.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Fri, 6 Aug 2010 18:48:27 +0000 (20:48 +0200)]
rt2x00: Update comments regarding TXWI and TX_STA_FIFO
Add some comments about the TXWI fields and the TX_STA_FIFO register.
Especially describe the relationship between the TXWI field PACKETID
and the PID field in the TX_STA_FIFO register.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 6 Aug 2010 18:47:57 +0000 (20:47 +0200)]
rt2x00: Implement TX status reporting for rt2800usb
The TX_STA_FIFO register which is used for per-frame TX frame
status reporting is also valid on rt2800usb. We can move the
rt2800pci_txdone function into rt2800lib where it can also
be used by rt2800usb.
rt2800usb needs to overwrite the txdone work handler to
a different function.
Both rt2800usb as rt2800_txdone need to take into account
that IO failures can occur while uploading the URB, which
means that when obtaining the new entry the IO status must
be checked.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 6 Aug 2010 18:47:20 +0000 (20:47 +0200)]
rt2x00: Request TXWI pointer from driver
The only reason why the write_tx_data callback function
is needed inside the driver, is because the location of
the TXWI descriptor is different on PCI and USB hardware.
Except for the beacon, where the TXWI is always at the
start of the SKB buffer.
In both cases the drivers write_tx_data function only
wrap around the function rt2800_write_txwi. Move write_tx_data
completely into the rt2800lib library, and add a callback
function to obtain the TXWI pointer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 6 Aug 2010 18:46:53 +0000 (20:46 +0200)]
rt2x00: Add helper function for reporting tx status
At some points, some drivers can't report the full TX status
information. This can happen for the UNKNOWN state, or the
FAILURE state (in case the URB failed).
Add a wrapper function to simplify reporting the
empty TX information.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 6 Aug 2010 18:46:19 +0000 (20:46 +0200)]
rt2x00: Set MIMO PS flag in tx descriptor for STAs in dynamic SMPS mode
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Fri, 6 Aug 2010 18:45:38 +0000 (20:45 +0200)]
rt2x00: Move USB tx/rx done handling to workqueue
Move all TX and RX completion handling into a work structure,
which is handeled on the mac80211 workqueue. This simplifies
the code in rt2x00lib since it no longer needs to check if the
device is USB or PCI to decide which mac80211 function should be used.
In the watchdog some changes are needed since it can no longer rely
on the TX completion function to be run while looping through the
entries. (Both functions now work on the same workqueue, so this
would deadlock). So the watchdog now waits for the URB to return,
and handle the TX status report directly.
As a side-effect, the debugfs entry for the RX queue now correctly
displays the positions of the INDEX and INDEX_DONE counters. This
also implies that it is not possible to perform checks like queue_empty()
and queue_full() on the RX queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ath9k_cmn_get_hw_crypto_keytype() instead which is
already exported and shared, and does exactly the same thing.
Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Thu, 5 Aug 2010 20:26:56 +0000 (22:26 +0200)]
drivers/net/wireless/ath/ath9k: Adjust confusing if indentation
Outdent the code following the if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 5 Aug 2010 15:45:15 +0000 (17:45 +0200)]
cfg80211: support sysfs namespaces
Enable using network namespaces with
wireless devices even when sysfs is
enabled using the same infrastructure
that was built for netdevs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 5 Aug 2010 15:05:55 +0000 (17:05 +0200)]
mac80211: allow drivers to request SM PS mode change
Sometimes drivers have more information than the
stack about how their antennas/chains are used,
and may require that the SM PS mode be changed.
This could happen, for example, when detecting
that the user disconnected an antenna. Thus this
patch introduces API to allow drivers to request
SM PS mode changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 5 Aug 2010 08:20:27 +0000 (10:20 +0200)]
cfg80211: deauth doesn't always imply disconnect
When an AP sends a deauth frame, or we send one
to an AP, that only means we lost our connection
if we were actually connected to that AP. Check
this to avoid sending spurious "disconnected"
events and breaking "iw ... link" reporting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces a new timer, which will release
queued-up MPDUs from the reorder buffer, whenever
they've waited for more than HT_RX_REORDER_BUF_TIMEOUT
(which is at around 100 ms).
The advantage of having a dedicated timer, instead of
relying on a constant stream of freshly arriving aMPDUs
to release the old ones, is particularly observable when
even a small fraction of MPDUs are forever lost at
low network speeds.
Previously under these circumstances frames would become
stuck in the reorder buffer and the network stack of both
HT peers throttled back, instead of revving up and
gunning the pipes.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes a few stale parameters and variables
which survived the last, large rx-path reorganization:
"mac80211: correctly place aMPDU RX reorder code"
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 2 Aug 2010 13:53:15 +0000 (15:53 +0200)]
ath9k: shorten the calibration interval during strong interference
When the noise floor limits are being bypassed because of strong
interference, sensitivity is also reduced.
In order to recover from this as quickly as possible, trigger a
long periodic calibration every second instead of every 30 seconds,
until the NF median is within limits again. This is especially important
if the interference lasts for a while, since it takes multiple clean
NF calibrations to bring the median back to normal.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 2 Aug 2010 13:53:14 +0000 (15:53 +0200)]
ath9k: use AP beacon miss as a trigger for fast recalibration
When beacons get stuck in AP mode, the most likely cause is interference.
Such interference can often go on for a while, and too many consecutive
beacon misses can lead to connected clients getting dropped.
Since connected clients might not be subjected to the same interference
if that happens to be very local, the AP should try to deal with it as
good as it can. One way to do this is to trigger an NF calibration with
automatic baseband update right after the beacon miss. In my tests with
very strong interference, this allowed the AP to continue transmitting
beacons after only 2-3 misses, which allows a normal client to stay
connected.
With some of the newer - really sensitive - chips, the maximum noise
floor limit is very low, which can be problematic during very strong
interference. To avoid an endless loop of stuck beacons -> nfcal ->
periodic calibration -> stuck beacons, the beacon miss event also sets
a flag, which allows the calibration code to bypass the chip specific
maximum NF value. This flag is automatically cleared, as soon as the
first NF median goes back below the limits for all chains.
In my tests, this allowed an ath9k AP to survive very strong interference
(measured NF: -68, or sometimes even higher) without losing connectivity
to its clients. Even under these conditions, I was able to transmit
several mbits/s through the interface.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 2 Aug 2010 13:53:12 +0000 (15:53 +0200)]
ath9k: add a separate debug level for stuck beacons
Stuck beacons are a useful indicator for debugging various PHY
issues such as calibration. Putting them on the same debug level
as the other beacon stuff makes it hard to spot them in huge amounts
of spam.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Hutchings [Sun, 1 Aug 2010 16:37:03 +0000 (17:37 +0100)]
mac80211: Don't squash error codes in key setup functions
ieee80211_add_key() currently returns -ENOMEM in case of any error,
including a missing crypto algorithm. Change ieee80211_key_alloc()
and ieee80211_aes_{key_setup_encrypt,cmac_key_setup}() to encode
errors with ERR_PTR() rather than returning NULL, and change
ieee80211_add_key() accordingly.
Compile-tested only.
Reported-by: Marcin Owsiany <porridge@debian.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 31 Jul 2010 15:34:10 +0000 (08:34 -0700)]
iwlwifi: track IBSS manager status
Only the IBSS manager, ie. the station that sent
the IBSS beacon last, should be replying to probe
responses. This requires implementing the mac80211
tx_last_beacon callback, which we can do thanks to
the ucode beacon notification.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 30 Jul 2010 14:46:07 +0000 (16:46 +0200)]
mac80211: unify scan and work mutexes
Having both scan and work mutexes is not just
a bit too fine grained, it also creates issues
when there's code that needs both since they
then need to be acquired in the right order,
which can be hard to do.
Therefore, use just a single mutex for both.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not need export iwl_bg.*scan.*() functions just for initialize
workqueue in other module. Making that functions static helps with
iwl-scan.c code review a bit.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 30 Jul 2010 11:23:12 +0000 (13:23 +0200)]
mac80211: don't check rates on PLCP error frames
Frames that failed PLCP error checks are most likely
microwave transmissions (well, maybe not ...) and
don't have a proper rate detected, so ignore it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 29 Jul 2010 15:36:43 +0000 (17:36 +0200)]
mac80211: fix driver offchannel notification when the channel does not change
When running in client mode and associating to an AP, the channel
change is usually performed with the offchannel flag still set.
However after the assoc is complete, the following channel change event
is suppressed because the run time channel is already set to the operating channel.
Fix this by sending channel change notifications to the driver even if
only the offchannel flag changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 26 May 2010 17:33:31 +0000 (13:33 -0400)]
rt2x00: do not shortcut rt2x00lib_config_antenna
This function was exiting early if the existing diversity settings
were unchanged. Unfortunately, in some cases the antenna configuration
is not initialized at all.
https://bugzilla.kernel.org/show_bug.cgi?id=14751
Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Cc: Gertjan van Wingerde <gwingerde@gmail.com>
b43: move hwrng registration driver to wireless core initialization
...and unregistration to core shutdown. Previously, the driver
remained registered even when the hardware was shutdown. That
causes the driver to return -ENODEV if the b43 device is IFF_DOWN.
This change causes the driver to disappear in that case, allowing
/dev/hwrng to still function if another hwrng device is available.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 10 Aug 2010 17:22:24 +0000 (13:22 -0400)]
iwm3200wifi: remove comparison to WIFI_IF_NTFY_MAX in iwm_ntf_wifi_if_wrapper
drivers/net/wireless/iwmc3200wifi/rx.c: In function 'iwm_ntf_wifi_if_wrapper':
drivers/net/wireless/iwmc3200wifi/rx.c:1198: warning: comparison is always true due to limited range of data type
This is, of course, because the value of WIFI_IF_NTFY_MAX is 0xff and
hdr->oid is a u8. This is obviously an attempt to verify the range on
an input value, but since it has no effect it can simply be removed.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
John W. Linville [Tue, 10 Aug 2010 17:08:11 +0000 (13:08 -0400)]
ipw2100: avoid warning from pointer cast in call to IPW_DEBUG_TX
drivers/net/wireless/ipw2x00/ipw2100.c: In function 'ipw2100_tx_send_commands':
drivers/net/wireless/ipw2x00/ipw2100.c:3063: warning: cast to pointer from integer of different size
This changes the cast and the conversion to match other usage of the
same value in calls to IPW_DEBUG_TX.
Reported-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some iwlwifi devices inexplicably disconnect themselves from the PCI-E
bus causing the predictable failures. This seems to disappear if ASPM
is disabled.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Thu, 29 Jul 2010 20:14:13 +0000 (16:14 -0400)]
mac80211: support use of NAPI for bottom-half processing
This patch implement basic infrastructure to support use of NAPI by
mac80211-based hardware drivers.
Because mac80211 devices can support multiple netdevs, a dummy netdev
is used for interfacing with the NAPI code in the core of the network
stack. That structure is hidden from the hardware drivers, but the
actual napi_struct is exposed in the ieee80211_hw structure so that the
poll routines in drivers can retrieve that structure. Hardware drivers
can also specify their own weight value for NAPI polling.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maxim Levitsky [Fri, 13 Aug 2010 15:27:28 +0000 (11:27 -0400)]
ath5k: disable ASPM L0s for all cards
Atheros PCIe wireless cards handled by ath5k do require L0s disabled.
For distributions shipping with CONFIG_PCIEASPM (this will be enabled
by default in the future in 2.6.36) this will also mean both L1 and L0s
will be disabled when a pre 1.1 PCIe device is detected. We do know L1
works correctly even for all ath5k pre 1.1 PCIe devices though but cannot
currently undue the effect of a blacklist, for details you can read
pcie_aspm_sanity_check() and see how it adjusts the device link
capability.
It may be possible in the future to implement some PCI API to allow
drivers to override blacklists for pre 1.1 PCIe but for now it is
best to accept that both L0s and L1 will be disabled completely for
distributions shipping with CONFIG_PCIEASPM rather than having this
issue present. Motivation for adding this new API will be to help
with power consumption for some of these devices.
Example of issues you'd see:
- On the Acer Aspire One (AOA150, Atheros Communications Inc. AR5001
Wireless Network Adapter [168c:001c] (rev 01)) doesn't work well
with ASPM enabled, the card will eventually stall on heavy traffic
with often 'unsupported jumbo' warnings appearing. Disabling
ASPM L0s in ath5k fixes these problems.
- On the same card you would see a storm of RXORN interrupts
even though medium is idle.
Credit for root causing and fixing the bug goes to Jussi Kivilinna.
Cc: David Quan <David.Quan@atheros.com> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Tim Gardner <tim.gardner@canonical.com> Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Cc: stable@kernel.org Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com> Signed-off-by: Yuri Kululin <ext-yuri.kululin@nokia.com> Acked-by: Kalle Valo <kvalo@adurom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan [Thu, 12 Aug 2010 08:53:28 +0000 (14:23 +0530)]
ath9k_htc: Fix disconnect issue in HT40 mode.
Some APs advertise that they may be HT40 capable in the capabilites
but the current operating channel configuration may be only HT20.
This causes disconnection as ath9k_htc sets WLAN_RC_40_FLAG despite
the AP operating in HT20 mode.
Hence set this flag only if the current channel configuration
is HT40 enabled.
Cc: stable@kernel.org Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 11 Aug 2010 20:11:00 +0000 (16:11 -0400)]
ipw2100: register pm_qos request before registering pci driver
It is necessary to call pm_qos_add_request prior to calling
pm_qos_update_request. It was revealed that ipw2100 has been
doing this wrong since "pm_qos: Get rid of the allocation in
pm_qos_add_request()" (commit 82f682514a5df89ffb3890627eebf0897b7a84ec)
added a WARN that results in the following backtrace:
projects / linux-beck.git / log