The length parameter should be sizeof(req->name) - 1 because there is no
guarantee that string provided by userspace will contain the trailing
'\0'.
Can be easily reproduced by manually setting req->name to 128 non-zero
bytes prior to ioctl(HIDPCONNADD) and checking the device name setup on
input subsystem:
Commit 23caaf19b11e (ALSA: usb-mixer: Add support for Audio Class v2.0)
forgot to adjust the length check for UAC 2.0 feature unit descriptors.
This would make the code abort on encountering a feature unit without
per-channel controls, and thus prevented the driver to work with any
device having such a unit, such as the RME Babyface or Fireface UCX.
Reported-by: Florian Hanisch <fhanisch@uni-potsdam.de> Tested-by: Matthew Robbetts <wingfeathera@gmail.com> Tested-by: Michael Beer <beerml@sigma6audio.de> Cc: Daniel Mack <daniel@caiaq.de> Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the next beacon is sent, the ath_buf from the previous run is reused.
If getting a new beacon from mac80211 fails, bf->bf_mpdu is not reset, yet
the skb is freed, leading to a double-free on the next beacon tx attempt,
resulting in a system crash.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SKBs that are allocated in the HTC layer do not have callbacks
registered and hence ended up not being freed, Fix this by freeing
them properly in the TX completion routine.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After sending reset command wait for its command complete event before
sending next command. Some chips sends CC event for command received
before reset if reset was send before chip replied with CC.
This is also required by specification that host shall not send
additional HCI commands before receiving CC for reset.
Subhash Jadavani reported this partial backtrace:
Now consider this call stack from MMC block driver (this is on the ARMv7
based board):
[<c001b50c>] (v7_dma_inv_range+0x30/0x48) from [<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c)
[<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c) from [<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c)
[<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c) from [<c0017ff8>] (dma_map_sg+0x3c/0x114)
This is caused by incrementing the struct page pointer, and running off
the end of the sparsemem page array. Fix this by incrementing by pfn
instead, and convert the pfn to a struct page.
Suggested-by: James Bottomley <JBottomley@Parallels.com> Tested-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When it goes to error through line 144, the memory allocated to *devname is
not freed, and the caller doesn't free it either in line 250. So we free the
memroy of *devname in function cifs_compose_mount_options() when it goes to
error.
Signed-off-by: Cong Ding <dinggnu@gmail.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioat does DMA memory sync with DMA_TO_DEVICE direction on a buffer allocated
for DMA_FROM_DEVICE dma, resulting in the following warning from dma debug.
Fixed the dma_sync_single_for_device() call to use the correct direction.
(in acpi_processor_power_init) and never sets the per_cpu idle
device. So when acpi_processor_hotplug on CPU online notification
tries to reference said device it crashes:
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We found a user code which was raising a divide-by-zero trap. That trap
would lead to XPC connections between system-partitions being torn down
due to the die_chain notifier callouts it received.
This also revealed a different issue where multiple callers into
xpc_die_deactivate() would all attempt to do the disconnect in parallel
which would sometimes lock up but often overwhelm the console on very
large machines as each would print at least one line of output at the
end of the deactivate.
I reviewed all the users of the die_chain notifier and changed the code
to ignore the notifier callouts for reasons which will not actually lead
to a system to continue on to call die().
[akpm@linux-foundation.org: fix ia64] Signed-off-by: Robin Holt <holt@sgi.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The traps are referred to by their numbers and it can be difficult to
understand them while reading the code without context. This patch adds
enumeration of the trap numbers and replaces the numbers with the correct
enum for x86.
Signed-off-by: Kees Cook <keescook@chromium.org> Link: http://lkml.kernel.org/r/20120310000710.GA32667@www.outflux.net Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Robin Holt <holt@sgi.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With virtual machines like qemu, it's pretty common to see "too much
work for irq4" messages nowadays. This happens when a bunch of output
is printed on the emulated serial console. This is caused by too low
PASS_LIMIT. When ISR loops more than the limit, it spits the message.
I've been using a kernel with doubled the limit and I couldn't see no
problems. Maybe it's time to get rid of the message now?
From SMBIOS 2.6 on, spec use little-endian encoding for UUID other than
network byte order.
So we need to get dmi version to distinguish. If version is 0.0, the
real version is taken from the SMBIOS version. This is part of original
kernel comment in code.
scsi_register_driver will register a prep_fn() function, which
in turn migh need to use the sd_cdp_pool for DIF.
Which hasn't been initialised at this point, leading to
a crash. So reshuffle the init_sd() and exit_sd() paths
to have the driver registered last.
Signed-off-by: Joel D. Diaz <joeldiaz@us.ibm.com> Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Cc: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1644) fixes a race that occurs during startup in
uhci-hcd. If the IRQ line is shared with other devices, it's possible
for the handler routine to be called before the data structures are
fully initialized.
The problem is fixed by adding a check to the IRQ handler routine. If
the initialization hasn't finished yet, the routine will return
immediately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Don Zickus <dzickus@redhat.com> Tested-by: "Huang, Adrian (ISS Linux TW)" <adrian.huang@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now using pcie_aspm=force will not enable ASPM if the FADT indicates
ASPM is unsupported. However, the semantics of force should probably allow
for this, especially as they did before 3c076351c4 ("PCI: Rework ASPM
disable code")
This patch just skips the clearing of any ASPM setup that the firmware has
carried out on this bus if pcie_aspm=force is being used.
Reference: http://bugs.launchpad.net/bugs/962038 Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If some other kernel subsystem has a module notifier, and adds a kprobe
to a ftrace mcount point (now that kprobes work on ftrace points),
when the ftrace notifier runs it will fail and disable ftrace, as well
as kprobes that are attached to ftrace points.
A kprobe was added to the init_once() function in the fat module on load.
But this happened before ftrace could have touched the code. As ftrace
didn't run yet, the kprobe system had no idea it was a ftrace point and
simply added a breakpoint to the code (0xcc in the cc:bb:d2:4b:e1).
Then when ftrace went to modify the location from a call to mcount/fentry
into a nop, it didn't see a call op, but instead it saw the breakpoint op
and not knowing what to do with it, ftrace shut itself down.
The solution is to simply give the ftrace module notifier the max priority.
This should have been done regardless, as the core code ftrace modification
also happens very early on in boot up. This makes the module modification
closer to core modification.
In the slow path, we are forced to copy the relocations prior to
acquiring the struct mutex in order to handle pagefaults. We forgo
copying the new offsets back into the relocation entries in order to
prevent a recursive locking bug should we trigger a pagefault whilst
holding the mutex for the reservations of the execbuffer. Therefore, we
need to reset the presumed_offsets just in case the objects are rebound
back into their old locations after relocating for this exexbuffer - if
that were to happen we would assume the relocations were valid and leave
the actual pointers to the kernels dangling, instant hang.
drm/i915: Handle pagefaults in execbuffer user relocations
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55984 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@fwll.ch> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vt6656 has several headers that use the #pragma pack(1) directive to
enable structure packing, but never disable it. The layout of
structures defined in other headers can then depend on which order the
various headers are included in, breaking the One Definition Rule.
In practice this resulted in crashes on x86_64 until the order of header
inclusion was changed for some files in commit 11d404cb56ecd ('staging:
vt6656: fix headers and add cfg80211.'). But we need a proper fix that
won't be affected by future changes to the order of inclusion.
This removes the #pragma pack(1) directives and adds __packed to the
structure definitions for which packing appears to have been intended.
When shut down SPI port, it's possible that MRDY has been asserted and a SPI
timer was activated waiting for SRDY assert, in the case, it needs to delete
this timer.
There has been an error on the xen_failsafe_callback path for failed
iret, which causes the stack pointer to be wrong when entering the
iret_exc error path. This can result in the kernel crashing.
In the classic kernel case, the relevant code looked a little like:
popl %eax # Error code from hypervisor
jz 5f
addl $16,%esp
jmp iret_exc # Hypervisor said iret fault
5: addl $16,%esp
# Hypervisor said segment selector fault
Here, there are two identical addls on either option of a branch which
appears to have been optimised by hoisting it above the jz, and
converting it to an lea, which leaves the flags register unaffected.
In the PVOPS case, the code looks like:
popl_cfi %eax # Error from the hypervisor
lea 16(%esp),%esp # Add $16 before choosing fault path
CFI_ADJUST_CFA_OFFSET -16
jz 5f
addl $16,%esp # Incorrectly adjust %esp again
jmp iret_exc
It is possible unprivileged userspace applications to cause this
behaviour, for example by loading an LDT code selector, then changing
the code selector to be not-present. At this point, there is a race
condition where it is possible for the hypervisor to return back to
userspace from an interrupt, fault on its own iret, and inject a
failsafe_callback into the kernel.
This bug has been present since the introduction of Xen PVOPS support
in commit 5ead97c84 (xen: Core Xen implementation), in 2.6.23.
Signed-off-by: Frediano Ziglio <frediano.ziglio@citrix.com> Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_alloc_segments_for_ring() builds a list of xhci_segments and links
the tail to head at the end (forming a ring). When it bails out for OOM
reasons half-way through, it tries to destroy its half-built list with
xhci_free_segments_for_ring(), even though it is not a ring yet. This
causes a null-pointer dereference upon hitting the last element.
Furthermore, one of its callers (xhci_ring_alloc()) mistakenly believes
the output parameters to be valid upon this kind of OOM failure, and
calls xhci_ring_free() on them. Since the (incomplete) list/ring should
already be destroyed in that case, this would lead to a use after free.
This patch fixes those issues by having xhci_alloc_segments_for_ring()
destroy its half-built, non-circular list manually and destroying the
invalid struct xhci_ring in xhci_ring_alloc() with a plain kfree().
This patch should be backported to kernels as old as 2.6.31, that
contains the commit 0ebbab37422315a5d0cb29792271085bafdf38c0 "USB: xhci:
Ring allocation and initialization."
A separate patch will need to be developed for kernels older than 3.4,
since the ring allocation code was refactored in that kernel.
Signed-off-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Julius Werner <jwerner@chromium.org> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
[bwh: Backported to 3.2:
- Adjust context
- Since segment allocation is done directly in xhci_ring_alloc(), walk
the list starting from ring->first_seg when freeing] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to prevent non-USB devices that have RMRRs associated with them from
being placed into the SI Domain during init. This fixes the issue where the RMRR info
for devices being placed in and out of the SI Domain gets lost.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com> Tested-by: Shuah Khan <shuah.khan@hp.com> Reviewed-by: Donald Dutile <ddutile@redhat.com> Reviewed-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Joerg Roedel <joro@8bytes.org> Signed-off-by: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1631) fixes a bug that shows up when a config change
fails for a device under an xHCI controller. The controller needs to
be told to disable the endpoints that have been enabled for the new
config. The existing code does this, but before storing the
information about which endpoints were enabled! As a result, any
second attempt to install the new config is doomed to fail because
xhci-hcd will refuse to enable an endpoint that is already enabled.
The patch optimistically initializes the new endpoints' device
structures before asking the device to switch to the new config. If
the request fails then the endpoint information is already stored, so
we can use usb_hcd_alloc_bandwidth() to disable the endpoints with no
trouble. The rest of the error path is slightly more complex now; we
have to disable the new interfaces and call put_device() rather than
simply deallocating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Matthias Schniedermeyer <ms@citd.de> CC: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: CAI Qian <caiqian@redhat.com>
Shuah Khan [Wed, 12 Dec 2012 23:27:51 +0000 (16:27 -0700)]
powerpc: fix wii_memory_fixups() compile error on 3.0.y tree
[not upstream as the code involved was removed in the 3.3.0 release]
Fix wii_memory_fixups() the following compile error on 3.0.y tree with
wii_defconfig on 3.0.y tree.
CC arch/powerpc/platforms/embedded6xx/wii.o
arch/powerpc/platforms/embedded6xx/wii.c: In function ‘wii_memory_fixups’:
arch/powerpc/platforms/embedded6xx/wii.c:88:2: error: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 2 has type ‘phys_addr_t’ [-Werror=format]
arch/powerpc/platforms/embedded6xx/wii.c:88:2: error: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘phys_addr_t’ [-Werror=format]
arch/powerpc/platforms/embedded6xx/wii.c:90:2: error: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 2 has type ‘phys_addr_t’ [-Werror=format]
arch/powerpc/platforms/embedded6xx/wii.c:90:2: error: format ‘%llx’ expects argument of type ‘long long unsigned int’, but argument 3 has type ‘phys_addr_t’ [-Werror=format]
cc1: all warnings being treated as errors
make[2]: *** [arch/powerpc/platforms/embedded6xx/wii.o] Error 1
make[1]: *** [arch/powerpc/platforms/embedded6xx] Error 2
make: *** [arch/powerpc/platforms] Error 2
SNB graphics devices have a bug that prevent them from accessing certain
memory ranges, namely anything below 1M and in the pages listed in the
table. So reserve those at boot if set detect a SNB gfx device on the
CPU to avoid GPU hangs.
Stephane Marchesin had a similar patch to the page allocator awhile
back, but rather than reserving pages up front, it leaked them at
allocation time.
[ hpa: made a number of stylistic changes, marked arrays as static
const, and made less verbose; use "memblock=debug" for full
verbosity. ]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Converting a 64 Bit TOD format value to nanoseconds means that the value
must be divided by 4.096. In order to achieve that we multiply with 125
and divide by 512.
When used within sched_clock() this triggers an overflow after appr.
417 days. Resulting in a sched_clock() return value that is much smaller
than previously and therefore may cause all sort of weird things in
subsystems that rely on a monotonic sched_clock() behaviour.
To fix this implement a tod_to_ns() helper function which converts TOD
values without overflow and call this function from both places that
open coded the conversion: sched_clock() and kvm_s390_handle_wait().
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear the target role when no target is provided for
the node performing a PRLI.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked by Robert Love <robert.w.love@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When generating a PRLI response to an initiator, clear the
FCP_SPPF_RETRY bit in the response.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked by Robert Love <robert.w.love@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the aux table is properly initialized, even when optional features
are missing. Without this, the FDPIC loader did not work. This was meant to
be included in commit d5ab780305bb6d60a7b5a74f18cf84eb6ad153b1.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'ni_at_a2150' module links to `cfc_write_to_buffer` in the
'comedi_fc' module, so selecting 'COMEDI_NI_AT_A2150' in the kernel config
needs to also select 'COMEDI_FC'.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
comedi_auto_config() associates a Comedi minor device number with an
auto-configured hardware device and comedi_auto_unconfig() disassociates
it. Currently, these use the hardware device's private data pointer to
point to some allocated storage holding the minor device number. This
is a bit of a waste of the hardware device's private data pointer,
preventing it from being used for something more useful by the low-level
comedi device drivers. For example, it would make more sense if
comedi_usb_auto_config() was passed a pointer to the struct
usb_interface instead of the struct usb_device, but this cannot be done
currently because the low-level comedi drivers already use the private
data pointer in the struct usb_interface for something more useful.
This patch stops the comedi core hijacking the hardware device's private
data pointer. Instead, comedi_auto_config() stores a pointer to the
hardware device's struct device in the struct comedi_device_file_info
associated with the minor device number, and comedi_auto_unconfig()
calls new function comedi_find_board_minor() to recover the minor device
number associated with the hardware device.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma_pte_free_pagetable() function will only free a page table page
if it is asked to free the *entire* 2MiB range that it covers. So if a
page table page was used for one or more small mappings, it's likely to
end up still present in the page tables... but with no valid PTEs.
This was fine when we'd only be repopulating it with 4KiB PTEs anyway
but the same virtual address range can end up being reused for a
*large-page* mapping. And in that case were were trying to insert the
large page into the second-level page table, and getting a complaint
from the sanity check in __domain_mapping() because there was already a
corresponding entry. This was *relatively* harmless; it led to a memory
leak of the old page table page, but no other ill-effects.
Fix it by calling dma_pte_clear_range (hopefully redundant) and
dma_pte_free_pagetable() before setting up the new large page.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Tested-by: Ravi Murty <Ravi.Murty@intel.com> Tested-by: Sudeep Dutt <sudeep.dutt@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: CAI Qian <caiqian@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In gfs2_trans_add_bh(), gfs2 was testing if a there was a bd attached to the
buffer without having the gfs2_log_lock held. It was then assuming it would
stay attached for the rest of the function. However, without either the log
lock being held of the buffer locked, __gfs2_ail_flush() could detach bd at any
time. This patch moves the locking before the test. If there isn't a bd
already attached, gfs2 can safely allocate one and attach it before locking.
There is no way that the newly allocated bd could be on the ail list,
and thus no way for __gfs2_ail_flush() to detach it.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK. If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).
The xHCI code to compute the NAK interval does not handle the special
case of zero properly. The current code unconditionally subtracts one
from bInterval and uses it as an exponent. This causes a very large
bInterval to be used, and warning messages like these will be printed:
usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes
This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.
This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math in
xhci_get_endpoint_interval()".
Reported-by: Vincent Pelletier <plr.vincent@gmail.com> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some touchscreens have buggy firmware which claims
remote wakeup to be enabled after a reset. They nevertheless
crash if the feature is cleared by the host.
Add a check for reset resume before checking for
an enabled remote wakeup feature. On compliant
devices the feature must be cleared after a reset anyway.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John's NEC 0.96 xHCI host controller needs a longer timeout for a warm
reset to complete. The logs show it takes 650ms to complete the warm
reset, so extend the hub reset timeout to 800ms to be on the safe side.
If we do have endpoints named like "ep-a" then bEndpointAddress is
counted internally by the gadget framework.
If we do have endpoints named like "ep-1" then bEndpointAddress is
assigned from the digit after "ep-".
If we do have both, then it is likely that after we used up the
"generic" endpoints we will use the digits and thus assign one
bEndpointAddress to multiple endpoints.
This theory can be proofed by using the completely enabled g_multi.
Without this patch, the mass storage won't enumerate and times out
because it shares endpoints with RNDIS.
This patch also adds fills up the endpoints list so we have in total
endpoints 1 to 15 in + out available while some of them are restricted
to certain types like BULK or ISO. Without this change the nokia gadget
won't load because the system does not provide enough (BULK) endpoints
but it did before ep-a - ep-f were removed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simple fix to add support for Crucible Technologies COMET Caller ID
USB decoder - a device containing FTDI USB/Serial converter chip,
handling 1200bps CallerID messages decoded from the phone line -
adding correct USB PID is sufficient.
Tested to apply cleanly and work flawlessly against 3.6.9, 3.7.0-rc8
and 3.8.0-rc3 on both amd64 and x86 arches.
Signed-off-by: Tomasz Mloduchowski <q@qdot.me> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a very old bug, but there's nothing that prevents the
timer from running while the module is being removed when we
only do del_timer() instead of del_timer_sync().
The timer should normally not be running at this point, but
it's not clearly impossible (or we could just remove this.)
Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those rn50 chip are often connected to console remoting hw and load
detection often fails with those. Just don't try to load detect and
report connect.
Éric Piel reported a kernel oops in the "comedi_test" module. It was a
NULL pointer dereference within `waveform_ai_interrupt()` (actually a
timer function) that sometimes occurred when a running asynchronous
command is cancelled (either by the `COMEDI_CANCEL` ioctl or by closing
the device file).
This seems to be a race between the caller of `waveform_ai_cancel()`
which on return from that function goes and tears down the running
command, and the timer function which uses the command. In particular,
`async->cmd.chanlist` gets freed (and the pointer set to NULL) by
`do_become_nonbusy()` in "comedi_fops.c" but a previously scheduled
`waveform_ai_interrupt()` timer function will dereference that pointer
regardless, leading to the oops.
Fix it by replacing the `del_timer()` call in `waveform_ai_cancel()`
with `del_timer_sync()`.
When a low-level comedi driver auto-configures a device, a `struct
comedi_dev_file_info` is allocated (as well as a `struct
comedi_device`) by `comedi_alloc_board_minor()`. A pointer to the
hardware `struct device` is stored as a cookie in the `struct
comedi_dev_file_info`. When the low-level comedi driver
auto-unconfigures the device, `comedi_auto_unconfig()` uses the cookie
to find the `struct comedi_dev_file_info` so it can detach the comedi
device from the driver, clean it up and free it.
A problem arises if the user manually unconfigures and reconfigures the
comedi device using the `COMEDI_DEVCONFIG` ioctl so that is no longer
associated with the original hardware device. The problem is that the
cookie is not cleared, so that a call to `comedi_auto_unconfig()` from
the low-level driver will still find it, detach it, clean it up and free
it.
Stop this problem occurring by always clearing the `hardware_device`
cookie in the `struct comedi_dev_file_info` whenever the
`COMEDI_DEVCONFIG` ioctl call is successful.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
appears in the kernel log. Through trial-and-error (the pxa270 developer's
manual is mostly incoherent on the topic of ac97 reset), I got cold reset to
complete by setting the WARM_RST bit in the GCR register (and later noticed that
pxa3xx does this for cold reset as well). Also, a timeout loop is needed to
wait for the reset to complete.
Tested on a palm treo 680 machine.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EPOLL_CTL_MOD sets the interest mask before calling f_op->poll() to
ensure events are not missed. Since the modifications to the interest
mask are not protected by the same lock as ep_poll_callback, we need to
ensure the change is visible to other CPUs calling ep_poll_callback.
We also need to ensure f_op->poll() has an up-to-date view of past
events which occured before we modified the interest mask. So this
barrier also pairs with the barrier in wq_has_sleeper().
This should guarantee either ep_poll_callback or f_op->poll() (or both)
will notice the readiness of a recently-ready/modified item.
This issue was encountered by Andreas Voellmy and Junchang(Jason) Wang in:
http://thread.gmane.org/gmane.linux.kernel/1408782/
Signed-off-by: Eric Wong <normalperson@yhbt.net> Cc: Hans Verkuil <hans.verkuil@cisco.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Cc: David Miller <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andreas Voellmy <andreas.voellmy@yale.edu> Tested-by: "Junchang(Jason) Wang" <junchang.wang@yale.edu> Cc: netdev@vger.kernel.org Cc: linux-fsdevel@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nlmsg_parse() might return an error, so test its return value before
potential random memory accesses.
Errors introduced in commit 115c9b81928 (rtnetlink: Fix problem with
buffer allocation)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement a new netlink attribute type IFLA_EXT_MASK. The mask
is a 32 bit value that can be used to indicate to the kernel that
certain extended ifinfo values are requested by the user application.
At this time the only mask value defined is RTEXT_FILTER_VF to
indicate that the user wants the ifinfo dump to send information
about the VFs belonging to the interface.
This patch fixes a bug in which certain applications do not have
large enough buffers to accommodate the extra information returned
by the kernel with large numbers of SR-IOV virtual functions.
Those applications will not send the new netlink attribute with
the interface info dump request netlink messages so they will
not get unexpectedly large request buffers returned by the kernel.
Modifies the rtnl_calcit function to traverse the list of net
devices and compute the minimum buffer size that can hold the
info dumps of all matching devices based upon the filter passed
in via the new netlink attribute filter mask. If no filter
mask is sent then the buffer allocation defaults to NLMSG_GOODSIZE.
With this change it is possible to add yet to be defined netlink
attributes to the dump request which should make it fairly extensible
in the future.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Acked-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.0:
- Adjust context
- Drop the change in do_setlink() that reverts commit f18da1456581
('net: RTNETLINK adjusting values of min_ifinfo_dump_size'), which
was never applied here] Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The message size allocated for rtnl ifinfo dumps was limited to
a single page. This is not enough for additional interface info
available with devices that support SR-IOV and caused a bug in
which VF info would not be displayed if more than approximately
40 VFs were created per interface.
Implement a new function pointer for the rtnl_register service that will
calculate the amount of data required for the ifinfo dump and allocate
enough data to satisfy the request.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Way Access Filter in recent AMD CPUs may hurt the performance of
some workloads, caused by aliasing issues in the L1 cache.
This patch disables it on the affected CPUs.
The issue is similar to that one of last year:
http://lkml.indiana.edu/hypermail/linux/kernel/1107.3/00041.html
This new patch does not replace the old one, we just need another
quirk for newer CPUs.
The performance penalty without the patch depends on the
circumstances, but is a bit less than the last year's 3%.
The workloads affected would be those that access code from the same
physical page under different virtual addresses, so different
processes using the same libraries with ASLR or multiple instances of
PIE-binaries. The code needs to be accessed simultaneously from both
cores of the same compute unit.
More details can be found here:
http://developer.amd.com/Assets/SharedL1InstructionCacheonAMD15hCPU.pdf
CPUs affected are anything with the core known as Piledriver.
That includes the new parts of the AMD A-Series (aka Trinity) and the
just released new CPUs of the FX-Series (aka Vishera).
The model numbering is a bit odd here: FX CPUs have model 2,
A-Series has model 10h, with possible extensions to 1Fh. Hence the
range of model ids.
On COW, a new hugepage is allocated and charged to the memcg. If the
system is oom or the charge to the memcg fails, however, the fault
handler will return VM_FAULT_OOM which results in an oom kill.
Instead, it's possible to fallback to splitting the hugepage so that the
COW results only in an order-0 page being allocated and charged to the
memcg which has a higher liklihood to succeed. This is expensive
because the hugepage must be split in the page fault handler, but it is
much better than unnecessarily oom killing a process.
Signed-off-by: David Rientjes <rientjes@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Johannes Weiner <jweiner@redhat.com> Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Michal Hocko <mhocko@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Incrementing lenExtents even while writing to a hole is bad
for performance as calls to udf_discard_prealloc and
udf_truncate_tail_extent would not return from start if
isize != lenExtents
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com> Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Shuah Khan <shuah.khan@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
blk_alloc_queue has already done a bdi_init, so do not bdi_init
again in aoeblk_gdalloc. The extra call causes list corruption
in the per-CPU backing dev info stats lists.
Affected users see console WARNINGs about list_del corruption on
percpu_counter_destroy when doing "rmmod aoe" or "aoeflush -a"
when AoE targets have been detected and initialized by the
system.
The patch below applies to v3.6.11, with its v47 aoe driver. It
is expected to apply to all currently maintained stable kernels
except 3.7.y. A related but different fix has been posted for
3.7.y.
References:
RedHat bugzilla ticket with original report
https://bugzilla.redhat.com/show_bug.cgi?id=853064
LKML discussion of bug and fix
http://thread.gmane.org/gmane.linux.kernel/1416336/focus=1416497
Commit c278531d39 added a warning when ext4_flush_unwritten_io() is
called without i_mutex being taken. It had previously not been taken
during orphan cleanup since races weren't possible at that point in
the mount process, but as a result of this c278531d39, we will now see
a kernel WARN_ON in this case. Take the i_mutex in
ext4_orphan_cleanup() to suppress this warning.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Reviewed-by: Zheng Liu <wenqing.lz@taobao.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a journal-less ext4 filesystem is mounted on a read-only block
device (blockdev --setro will do), each remount (for other, unrelated,
flags, like suid=>nosuid etc) results in a series of scary messages
from kernel telling about I/O errors on the device.
This is becauese of the following code ext4_remount():
if (sbi->s_journal == NULL)
ext4_commit_super(sb, 1);
at the end of remount procedure, which forces writing (flushing) of
a superblock regardless whenever it is dirty or not, if the filesystem
is readonly or not, and whenever the device itself is readonly or not.
We only need call ext4_commit_super when the file system had been
previously mounted read/write.
Thanks to Eric Sandeen for help in diagnosing this issue.
The following race is possible between start_this_handle() and someone
calling jbd2_journal_flush().
Process A Process B
start_this_handle().
if (journal->j_barrier_count) # false
if (!journal->j_running_transaction) { #true
read_unlock(&journal->j_state_lock);
jbd2_journal_lock_updates()
jbd2_journal_flush()
write_lock(&journal->j_state_lock);
if (journal->j_running_transaction) {
# false
... wait for committing trans ...
write_unlock(&journal->j_state_lock);
...
write_lock(&journal->j_state_lock);
if (!journal->j_running_transaction) { # true
jbd2_get_transaction(journal, new_transaction);
write_unlock(&journal->j_state_lock);
goto repeat; # eventually blocks on j_barrier_count > 0
...
J_ASSERT(!journal->j_running_transaction);
# fails
We fix the race by rechecking j_barrier_count after reacquiring j_state_lock
in exclusive mode.
Reported-by: yjwsignal@empal.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: "Theodore Ts'o" <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VDCTRL4 register does not provide the MXS SET/CLR/TOGGLE feature.
The write in mxsfb_disable_controller() sets the data_cnt for the LCD
DMA to 0 which obviously means the max. count for the LCD DMA and
leads to overwriting arbitrary memory when the display is unblanked.
Abort dm ioctl processing if userspace changes the data_size parameter
after we validated it but before we finished copying the data buffer
from userspace.
The dm ioctl parameters are processed in the following sequence:
1. ctl_ioctl() calls copy_params();
2. copy_params() makes a first copy of the fixed-sized portion of the
userspace parameters into the local variable "tmp";
3. copy_params() then validates tmp.data_size and allocates a new
structure big enough to hold the complete data and copies the whole
userspace buffer there;
4. ctl_ioctl() reads userspace data the second time and copies the whole
buffer into the pointer "param";
5. ctl_ioctl() reads param->data_size without any validation and stores it
in the variable "input_param_size";
6. "input_param_size" is further used as the authoritative size of the
kernel buffer.
The problem is that userspace code could change the contents of user
memory between steps 2 and 4. In particular, the data_size parameter
can be changed to an invalid value after the kernel has validated it.
This lets userspace force the kernel to access invalid kernel memory.
The fix is to ensure that the size has not changed at step 4.
This patch shouldn't have a security impact because CAP_SYS_ADMIN is
required to run this code, but it should be fixed anyway.
The function rb_check_pages() was added to make sure the ring buffer's
pages were sane. This check is done when the ring buffer size is modified
as well as when the iterator is released (closing the "trace" file),
as that was considered a non fast path and a good place to do a sanity
check.
The problem is that the check does not have any locks around it.
If one process were to read the trace file, and another were to read
the raw binary file, the check could happen while the reader is reading
the file.
The issues with this is that the check requires to clear the HEAD page
before doing the full check and it restores it afterward. But readers
require the HEAD page to exist before it can read the buffer, otherwise
it gives a nasty warning and disables the buffer.
By adding the reader lock around the check, this keeps the race from
happening.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device IDs for WiMAX function of Intel 6150 cards.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Users of jffs2_do_reserve_space() expect they still held
erase_completion_lock after call to it. But there is a path
where jffs2_do_reserve_space() leaves erase_completion_lock unlocked.
The patch fixes it.
Found by Linux Driver Verification project (linuxtesting.org).
This patch ensures that we free the rpc_task after the cleanup callbacks
are done in order to avoid a deadlock problem that can be triggered if
the callback needs to wait for another workqueue item to complete.
projects / karo-tx-linux.git / log