can: gs_usb: add ethtool set_phys_id callback to locate physical device
This patch Implements the ethtool set_phys_id callback to ease the
locating of specific physical devices. Currently only supported on
candleLight interfaces.
Signed-off-by: Hubert Denkmair <hubert@denkmair.de> Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
[mkl: split codingstyle change sinto separate patch] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: gs_usb: codingstyle: introduce use of BIT() + fix indention
This patch converts "1 << n" by BIT(n) and fixes the indention. No
functional change.
Signed-off-by: Hubert Denkmair <hubert@denkmair.de> Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
[mkl: split codingstyle changes into separate patch] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This driver does not do anything special in module init/exit. This patch
eliminates the module init/exit boilerplate code by utilizing the
module_isa_driver macro.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marek Vasut [Thu, 9 Jun 2016 19:21:00 +0000 (21:21 +0200)]
can: slcan: Replace sizeof struct can_frame with CAN_MTU
Use CAN_MTU macro instead of sizeof(struct can_frame) just like the
other drivers do.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
can: dev: can-calc-bit-timing(): better sample point calculation
This patch optimizes the calculation of the sample point. To understand what it
does have a look at the original implementation.
If there is a combination of timing parameters where both the bitrate and
sample point error are 0 the current implementation will find it.
However if the reference clock doesn't allow an optimal bitrate (this means the
bitrate error is always != 0) there might be several timing parameter
combinations having the same bitrate error. The original implementation will
allways choose the one with the highest brp. The actual sample point error
isn't taken into account.
This patch changes the algorithm to minimize the sample point error, too. Now a
brp/tseg combination is accepted as better if one of these condition are
fulfilled:
1) the bit rate error must be smaller, or
2) the bit rate error must be equal and
the sample point error must be equal or smaller
If a smaller bit rate error is found the sample point error is reset. This
ensures that we first optimize for small bit rate error and then for small
sample point errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Alexander Aring [Mon, 23 May 2016 13:13:00 +0000 (15:13 +0200)]
can: build proc support only if CONFIG_PROC_FS is activated
When building can subsystem with CONFIG_PROC_FS=n I detected some unused
variables warning by using proc functions. In CAN the proc handling is
nicely placed in one object file. This patch adds simple add a
dependency on CONFIG_PROC_FS for CAN's proc.o file and corresponding
static inline no-op functions.
Signed-off-by: Alexander Aring <aar@pengutronix.de> Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
[mkl: provide static inline noops instead of using #ifdefs] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Daniel Borkmann [Thu, 16 Jun 2016 21:19:29 +0000 (23:19 +0200)]
net, cls: also reject deleting all filters when TCA_KIND present
When we check for RTM_DELTFILTER, we should also reject the request
for deleting all filters under a given parent when TCA_KIND attribute
is present. If present, it's currently just ignored but there's also
no point to let it pass in the first place either since this doesn't
have any meaning with wild-card removal.
Fixes: ea7f8277f907 ("net, cls: allow for deleting all filters for given parent") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 17 Jun 2016 05:37:05 +0000 (22:37 -0700)]
Merge branch 'vmxnet3-upgrade-to-version3'
Shrikrishna Khare says:
====================
vmxnet3: upgrade to version 3
vmxnet3 emulation has recently added several new features which includes
support for new commands the driver can issue to emulation, change in
descriptor fields etc. This patch series extends the vmxnet3 driver to
leverage these new features.
Compatibility is maintained using existing vmxnet3 versioning mechanism as
follows:
- new features added to vmxnet3 emulation are associated with new vmxnet3
version viz. vmxnet3 version 3.
- emulation advertises all the versions it supports to the driver.
- during initialization, vmxnet3 driver picks the highest version number
supported by both the emulation and the driver and configures emulation
to run at that version.
In particular, following changes are introduced:
Patch 1:
Some command definitions from previous vmxnet3 versions are
missing. This patch adds those definitions before moving to vmxnet3
version 3. It also fixes copyright info and maintained by.
Patch 2:
This patch introduces generalized command interface which allows
for easily adding new commands that vmxnet3 driver can issue to the
emulation. Further patches in this series make use of this facility.
Patch 3:
Transmit data ring buffer is used to copy packet headers or small
packets. It is a fixed size buffer. This patch extends the driver to
allow variable sized transmit data ring buffer.
Patch 4:
This patch introduces receive data ring buffer - a set of small sized
buffers that are always mapped by the emulation. This avoids memory
mapping/unmapping overhead for small packets.
Patch 5:
The vmxnet3 emulation supports a variety of coalescing modes. This patch
extends vmxnet3 driver to allow querying and configuring these modes.
Patch 6:
In vmxnet3 version 3, the emulation added support for the vmxnet3 driver
to communicate information about the memory regions the driver will use
for rx/tx buffers. This patch exposes related commands to the driver.
Patch 7:
With all vmxnet3 version 3 changes incorporated in the vmxnet3 driver,
with this patch, the driver can configure emulation to run at vmxnet3
version 3.
Changes in v2:
- v1 patch used special values of rx-usecs to differentiate between
coalescing modes. v2 uses relevant fields in struct ethtool_coalesce
to choose modes. Also, a new command VMXNET3_CMD_GET_COALESCE
is introduced which allows driver to query the device for default
coalescing configuration.
Changes in v3:
- fix subject line to use vmxnet3: instead of Driver:Vmxnet3
- resubmit when net-next is open
Changes in v4:
- Address code review comments by Ben Hutchings: remove unnecessary memset
from vmxnet3_get_coalesce.
Changes in v5:
- Updated all the patches to add detailed commit messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With all vmxnet3 version 3 changes incorporated in the vmxnet3 driver,
the driver can configure emulation to run at vmxnet3 version 3, provided
the emulation advertises support for version 3.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3: introduce command to register memory region
In vmxnet3 version 3, the emulation added support for the vmxnet3 driver
to communicate information about the memory regions the driver will use
for rx/tx buffers. The driver can also indicate which rx/tx queue the
memory region is applicable for. If this information is communicated
to the emulation, the emulation will always keep these memory regions
mapped, thereby avoiding the mapping/unmapping overhead for every packet.
Currently, Linux vmxnet3 driver does not leverage this capability. The
feasibility of using this approach for the Linux vmxnet3 driver will be
investigated independently and if possible, will be part of a different
patch. This patch only exposes the emulation capability to the driver
(vmxnet3_defs.h is identical between the driver and the emulation).
Signed-off-by: Guolin Yang <gyang@vmware.com> Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3: add support for get_coalesce, set_coalesce ethtool operations
The emulation supports a variety of coalescing modes viz. disabled
(no coalescing), adaptive, static (number of packets to batch before
raising an interrupt), rate based (number of interrupts per second).
This patch implements get_coalesce and set_coalesce methods to allow
querying and configuring different coalescing modes.
Signed-off-by: Keyong Sun <sunk@vmware.com> Signed-off-by: Manoj Tammali <tammalim@vmware.com> Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 driver preallocates buffers for receiving packets and posts the
buffers to the emulation. In order to deliver a received packet to the
guest, the emulation must map buffer(s) and copy the packet into it.
To avoid this memory mapping overhead, this patch introduces the receive
data ring - a set of small sized buffers that are always mapped by
the emulation. If a packet fits into the receive data ring buffer, the
emulation delivers the packet via the receive data ring (which must be
copied by the guest driver), or else the usual receive path is used.
Receive Data Ring buffer length is configurable via ethtool -G ethX rx-mini
Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3: allow variable length transmit data ring buffer
vmxnet3 driver supports transmit data ring viz. a set of fixed size
buffers used by the driver to copy packet headers. Small packets that
fit these buffers are copied into these buffers entirely.
Currently this buffer size of fixed at 128 bytes. This patch extends
transmit data ring implementation to allow variable length transmit
data ring buffers. The length of the buffer is read from the emulation
during initialization.
Signed-off-by: Sriram Rangarajan <rangarajans@vmware.com> Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3: introduce generalized command interface to configure the device
Shared memory is used to exchange information between the vmxnet3 driver
and the emulation. In order to request emulation to perform a task, the
driver first populates specific fields in this shared memory and then
issues corresponding command by writing to the command register(CMD). The
layout of the shared memory was defined by vmxnet3 version 1 and cannot
be extended for every new command without breaking backward compatibility.
To address this problem, in vmxnet3 version 3, the emulation repurposed
a reserved field in the shared memory to represent command information
instead. For new commands, the driver first populates the command
information field in the shared memory and then issues the command. The
emulation interprets the data written to the command information depending
on the type of the command. This patch exposes this capability to the driver.
Signed-off-by: Guolin Yang <gyang@vmware.com> Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 is currently at version 2, but some command definitions from
previous vmxnet3 versions are missing. Add those definitions before
moving to version 3.
Also, introduce utility macros for vmxnet3 version comparison and update
Copyright information and Maintained by.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastian Ott [Thu, 16 Jun 2016 14:19:03 +0000 (16:19 +0200)]
s390/qeth: fix indentation in qeth_l3_arp_query
gcc-6 warns about obviously wrong indentation:
drivers/s390/net/qeth_l3_main.c: In function 'qeth_l3_arp_query':
drivers/s390/net/qeth_l3_main.c:2315:3: warning: this 'if' clause does not
guard... [-Wmisleading-indentation]
if (copy_to_user(udata, qinfo.udata, 4))
^~
drivers/s390/net/qeth_l3_main.c:2317:4: note: ...this statement, but the
latter is misleadingly indented as if it is guarded by the 'if'
goto free_and_out;
^~~~
Although this particular case is harmless, fix the indentation to get rid
of that warning and improve readability.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans Wippel [Thu, 16 Jun 2016 14:19:02 +0000 (16:19 +0200)]
qeth: omit outbound queue 3 for unicast packets in Priority Queuing on HiperSockets
On HiperSockets only outbound queues 0 to 2 are available for unicast
packets. Current Priority Queuing implementation in the qeth driver puts
outgoing packets in outbound queues 0 to 3.
This puts outgoing unicast packets into outbound queue 2 instead of
outbound queue 3 when using Priority Queuing on a HiperSocket.
Additionally, the default outbound queue cannot be set to outbound queue 3
on HiperSockets.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans Wippel [Thu, 16 Jun 2016 14:19:01 +0000 (16:19 +0200)]
qeth: improve set_features error handling
The function set_features is called to configure network device features
on the hardware. If errors occur, the network device features should
reflect the changed hardware state and the function should return an
error in order to notify the user.
In case of an error, the current implementation does not necessarily
save the changed hardware state in the network device features before an
error is returned.
This patch improves error handling by saving features, that could be
changed, to the network device features before returning an error. If
the device is not running, an additional check in fix_features removes
features, that require hardware changes, before they are passed to
set_features. Thus, the corresponding check was removed in set_features.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hans Wippel [Thu, 16 Jun 2016 14:19:00 +0000 (16:19 +0200)]
qeth: add network device features for VLAN devices
Network device features indicate the capabilities of network devices (e.g.,
TX checksum offloading and TSO) and their configuration state. Additional
network device features (vlan_features) indicate for each network device,
which capabilities can be used on VLAN devices, that are configured on the
respective base network device.
In the current qeth implementation, network device features are only set
for the base network devices and not for the VLAN devices. Thus, features
like TX checksum offloading cannot be used on VLAN devices.
This patch adds network device features to vlan_features, so they can be
used by VLAN devices.
Signed-off-by: Hans Wippel <hwippel@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Richter [Thu, 16 Jun 2016 14:18:59 +0000 (16:18 +0200)]
qeth layer 2 and layer 3 common feature handling
This patch introduces a common set of fix_features and set_features
functions for layer 2 and layer 3. The RX, TX and TSO offload
functionality on the OSA card is enabled using ethtool at user's
request and not at device initialization as done before.
For layer 3 the RX checksum offloading is disabled at device
initialization time.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lakhvich Dmitriy [Thu, 16 Jun 2016 14:18:58 +0000 (16:18 +0200)]
qeth: optimize IP handling in rx_mode callback
In layer3 mode of the qeth driver, multicast IP addresses
from struct net_device and other type of IP addresses
from other sources require mapping to the OSA-card.
This patch simplifies the IP address mapping logic, and changes imple-
mentation of ndo_set_rx_mode callback and ip notifier events.
Addresses are stored in private hashtables instead of lists now.
It allows hardware registration/removal for new/deleted multicast
addresses only.
Signed-off-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Evgeny Cherkashin <Eugene.Crosser@ru.ibm.com> Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Thu, 16 Jun 2016 14:18:57 +0000 (16:18 +0200)]
qeth: introduce linearization fail count to stats
When skb data touches too many pages, skb_linearize() is called
opportunistically in the hope that less pages will be required
for a big linear buffer than for multiple fragments. This patch
intoduces a separate counter in ethtool statistics structure
representing _failed_ linearization attempts.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com> Reviewed-by: Thomas Richter <tmricht@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Thu, 16 Jun 2016 14:18:56 +0000 (16:18 +0200)]
qeth: enable scatter/gather by default
Set scatter/gather ON by default on OSA, for both layer 2 and
layer 3 modes. We always use fragmentation over QDIO anyway,
so let the upper layers of the stack take advantage of that.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com> Reviewed-by: Thomas Richter <tmricht@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Thu, 16 Jun 2016 14:18:55 +0000 (16:18 +0200)]
qeth: enable scatter/gather in layer 2 mode
The patch enables NETIF_F_SG flag for OSA in layer 2 mode.
It also adds performance accounting for fragmented sends,
adds a conditional skb_linearize() attempt if the skb had
too many fragments for QDIO SBAL, and fills netdevice->gso_*
attributes.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Reviewed-by: Lakhvich Dmitriy <ldmitriy@ru.ibm.com> Reviewed-by: Thomas Richter <tmricht@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Thu, 16 Jun 2016 14:18:54 +0000 (16:18 +0200)]
qeth: fill netdevice->gso_* attributes accurately
Use QETH_MAX_BUFFER_ELEMENTS(card) instead of constant 16.
Also fill gso_max_segs and gso_min_segs.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Thu, 16 Jun 2016 14:18:53 +0000 (16:18 +0200)]
qeth: clean up condition when tso is used
Make conditions under which TSO is activated more stringent.
Make calculation of SBALEs required for the skb more accurate.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Thu, 16 Jun 2016 14:18:52 +0000 (16:18 +0200)]
qeth: refactor calculation of SBALE count
Rewrite the functions that calculate the required number of buffer
elements needed to represent SKB data, to make them hopefully more
comprehensible. Plus a few cleanups.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eugene Crosser [Thu, 16 Jun 2016 14:18:51 +0000 (16:18 +0200)]
qeth: Include error message for "OS Mismatch"
Having understood the semantics of BRIDGEPORT error code 0x0010,
we can introduce a meaningful error message.
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 16 Jun 2016 13:59:25 +0000 (15:59 +0200)]
net: xfrm: fix old-style declaration
Modern C standards expect the '__inline__' keyword to come before the return
type in a declaration, and we get a couple of warnings for this with "make W=1"
in the xfrm{4,6}_policy.c files:
net/ipv6/xfrm6_policy.c:369:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static int inline xfrm6_net_sysctl_init(struct net *net)
net/ipv6/xfrm6_policy.c:374:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static void inline xfrm6_net_sysctl_exit(struct net *net)
net/ipv4/xfrm4_policy.c:339:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static int inline xfrm4_net_sysctl_init(struct net *net)
net/ipv4/xfrm4_policy.c:344:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static void inline xfrm4_net_sysctl_exit(struct net *net)
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 16 Jun 2016 13:52:12 +0000 (15:52 +0200)]
isdn: eicon: fix old-style declarations
Modern C standards expect the '__inline__' keyword to come before the return
type in a declaration, and we get many warnings for this with "make W=1"
because the eicon driver has this in a header file:
eicon/divasmain.c:448:1: error: '__inline__' is not at beginning of declaration [-Werror=old-style-declaration]
eicon/divasmain.c:453:1: error: '__inline__' is not at beginning of declaration [-Werror=old-style-declaration]
eicon/divasmain.c:458:1: error: '__inline__' is not at beginning of declaration [-Werror=old-style-declaration]
eicon/divasmain.c:463:1: error: '__inline__' is not at beginning of declaration [-Werror=old-style-declaration]
eicon/divasmain.c:468:1: error: '__inline__' is not at beginning of declaration [-Werror=old-style-declaration]
eicon/divasmain.c:473:1: error: '__inline__' is not at beginning of declaration [-Werror=old-style-declaration]
eicon/platform.h:274:1: error: '__inline__' is not at beginning of declaration [-Werror=old-style-declaration]
eicon/platform.h:280:1: error: '__inline__' is not at beginning of declaration [-Werror=old-style-declaration]
A similar warning gets printed for the diva_os_register_io_port()
declaration, because 'register' is interpreted as a keyword instead
of a variable name:
In file included from eicon/diva_didd.c:21:0:
eicon/platform.h:206:1: error: 'register' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 16 Jun 2016 11:38:23 +0000 (13:38 +0200)]
net: tlan: don't set unused function argument
We get a warning for tlan_handle_tx_eoc when building with "make W=1"
drivers/net/ethernet/ti/tlan.c: In function 'tlan_handle_tx_eoc':
drivers/net/ethernet/ti/tlan.c:1647:59: error: parameter 'host_int' set but not used [-Werror=unused-but-set-parameter]
static u32 tlan_handle_tx_eoc(struct net_device *dev, u16 host_int)
This is harmless, but removing the unused assignment lets us avoid
the warning with no downside.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 16 Jun 2016 11:38:22 +0000 (13:38 +0200)]
net: qlcnic: don't set unused function argument
We get a warning for qlcnic_83xx_get_mac_address when building with
"make W=1":
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c: In function 'qlcnic_83xx_get_mac_address':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:2156:8: error: parameter 'function' set but not used [-Werror=unused-but-set-parameter]
Clearly this is harmless, but there is also no point for setting
the variable, so we can simply remove the assignment.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 16 Jun 2016 09:00:05 +0000 (11:00 +0200)]
dsa: b53: fix big-endian register access
The b53 dsa register access confusingly uses __raw register accessors
when both the CPU and the device are big-endian, but it uses little-
endian accessors when the same device is used from a little-endian
CPU, which makes no sense.
This uses normal accessors in device-endianess all the time, which
will work in all four combinations of register and CPU endianess,
and it will have the same barrier semantics in all cases.
This also seems to take care of a (false positive) warning I'm getting:
drivers/net/dsa/b53/b53_mmap.c: In function 'b53_mmap_read64':
drivers/net/dsa/b53/b53_mmap.c:109:10: error: 'hi' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*val = ((u64)hi << 32) | lo;
I originally planned to submit another patch for that warning
and did this one as a preparation cleanup, but it does seem to be
sufficient by itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Thu, 16 Jun 2016 08:09:09 +0000 (17:09 +0900)]
mpls: allow routes on ipgre devices
This appears to be necessary and sufficient to provide
MPLS in GRE (RFC4023) support.
This can be used by establishing an ipgre tunnel device
and then routing MPLS over it.
The following example will forward MPLS frames received with an outermost
MPLS label 100 over tun1, a GRE tunnel. The forwarded packet will have the
outermost MPLS LSE removed and two new LSEs added with labels 200
(outermost) and 300 (next).
ip link add name tun1 type gre remote 10.0.99.193 local 10.0.99.192 ttl 225
ip link set up dev tun1
ip addr add 10.0.98.192/24 dev tun1
ip route sh
echo 1 > /proc/sys/net/mpls/conf/eth0/input
echo 101 > /proc/sys/net/mpls/platform_labels
ip -f mpls route add 100 as 200/300 via inet 10.0.98.193
ip -f mpls route sh
Also remove unnecessary braces.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Acked-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Wed, 15 Jun 2016 22:12:48 +0000 (00:12 +0200)]
net: ethernet: ax88796: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Jun 2016 21:14:58 +0000 (14:14 -0700)]
Merge branch 'stmmac-wol'
Vincent Palatin says:
====================
net: stmmac: dwmac-rk: fixes for Wake-on-Lan on RK3288
In order to support Wake-On-Lan when using the RK3288 integrated MAC
(with an external RGMII PHY), we need to avoid shutting down the regulator
of the external PHY when the MAC is suspended as it's currently done in the MAC
platform code.
As a first step, create independant callbacks for suspend/resume rather than
re-using exit/init callbacks. So the dwmac platform driver can behave differently
on suspend where it might skip shutting the PHY and at module unloading.
Then update the dwmac-rk driver to switch off the PHY regulator only if we are
not planning to wake up from the LAN.
Finally add the PMT interrupt to the MAC device tree configuration, so we can
wake up the core from it when the PHY has received the magic packet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Palatin [Wed, 15 Jun 2016 18:32:23 +0000 (11:32 -0700)]
ARM: dts: rockchip: add interrupt for Wake-on-Lan on RK3288
In order to use Wake-on-Lan on RK3288 integrated MAC, we need to wake-up
the CPU on the PMT interrupt when the MAC and the PHY are in low power mode.
Adding the interrupt declaration.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Palatin [Wed, 15 Jun 2016 18:32:22 +0000 (11:32 -0700)]
net: stmmac: dwmac-rk: keep the PHY up for WoL
When suspending the machine, do not shutdown the external PHY by cutting
its regulator in the mac platform driver suspend code if Wake-on-Lan is enabled,
else it cannot wake us up.
In order to do this, split the suspend/resume callbacks from the
init/exit callbacks, so we can condition the power-down on the lack of
need to wake-up from the LAN but do it unconditionally when unloading the
module.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Palatin [Wed, 15 Jun 2016 18:32:21 +0000 (11:32 -0700)]
net: stmmac: allow to split suspend/resume from init/exit callbacks
Let the stmmac platform drivers provide dedicated suspend and resume
callbacks rather than always re-using the init and exits callbacks.
If the driver does not provide the suspend or resume callback, we fall
back to the old behavior trying to use exit or init.
This allows a specific platform to perform only a partial power-down on
suspend if Wake-on-Lan is enabled but always perform the full shutdown
sequence if the module is unloaded.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Wed, 15 Jun 2016 17:15:06 +0000 (01:15 +0800)]
sctp: change sk state to CLOSED instead of CLOSING in sctp_sock_migrate
Commit d46e416c11c8 ("sctp: sctp should change socket state when
shutdown is received") may set sk_state CLOSING in sctp_sock_migrate,
but inet_accept doesn't allow the sk_state other than ESTABLISHED/
CLOSED for sctp. So we will change sk_state to CLOSED, instead of
CLOSING, as actually sk is closed already there.
Fixes: d46e416c11c8 ("sctp: sctp should change socket state when shutdown is received") Reported-by: Ye Xiaolong <xiaolong.ye@intel.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This set improves BPF perf fd array map release wrt to purging
entries, first two extend the API as needed. Please see individual
patches for more details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 15 Jun 2016 20:47:14 +0000 (22:47 +0200)]
bpf, maps: flush own entries on perf map release
The behavior of perf event arrays are quite different from all
others as they are tightly coupled to perf event fds, f.e. shown
recently by commit e03e7ee34fdd ("perf/bpf: Convert perf_event_array
to use struct file") to make refcounting on perf event more robust.
A remaining issue that the current code still has is that since
additions to the perf event array take a reference on the struct
file via perf_event_get() and are only released via fput() (that
cleans up the perf event eventually via perf_event_release_kernel())
when the element is either manually removed from the map from user
space or automatically when the last reference on the perf event
map is dropped. However, this leads us to dangling struct file's
when the map gets pinned after the application owning the perf
event descriptor exits, and since the struct file reference will
in such case only be manually dropped or via pinned file removal,
it leads to the perf event living longer than necessary, consuming
needlessly resources for that time.
Relations between perf event fds and bpf perf event map fds can be
rather complex. F.e. maps can act as demuxers among different perf
event fds that can possibly be owned by different threads and based
on the index selection from the program, events get dispatched to
one of the per-cpu fd endpoints. One perf event fd (or, rather a
per-cpu set of them) can also live in multiple perf event maps at
the same time, listening for events. Also, another requirement is
that perf event fds can get closed from application side after they
have been attached to the perf event map, so that on exit perf event
map will take care of dropping their references eventually. Likewise,
when such maps are pinned, the intended behavior is that a user
application does bpf_obj_get(), puts its fds in there and on exit
when fd is released, they are dropped from the map again, so the map
acts rather as connector endpoint. This also makes perf event maps
inherently different from program arrays as described in more detail
in commit c9da161c6517 ("bpf: fix clearing on persistent program
array maps").
To tackle this, map entries are marked by the map struct file that
added the element to the map. And when the last reference to that map
struct file is released from user space, then the tracked entries
are purged from the map. This is okay, because new map struct files
instances resp. frontends to the anon inode are provided via
bpf_map_new_fd() that is called when we invoke bpf_obj_get_user()
for retrieving a pinned map, but also when an initial instance is
created via map_create(). The rest is resolved by the vfs layer
automatically for us by keeping reference count on the map's struct
file. Any concurrent updates on the map slot are fine as well, it
just means that perf_event_fd_array_release() needs to delete less
of its own entires.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 15 Jun 2016 20:47:13 +0000 (22:47 +0200)]
bpf, maps: extend map_fd_get_ptr arguments
This patch extends map_fd_get_ptr() callback that is used by fd array
maps, so that struct file pointer from the related map can be passed
in. It's safe to remove map_update_elem() callback for the two maps since
this is only allowed from syscall side, but not from eBPF programs for these
two map types. Like in per-cpu map case, bpf_fd_array_map_update_elem()
needs to be called directly here due to the extra argument.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 15 Jun 2016 20:47:12 +0000 (22:47 +0200)]
bpf, maps: add release callback
Add a release callback for maps that is invoked when the last
reference to its struct file is gone and the struct file about
to be released by vfs. The handler will be used by fd array maps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Jun 2016 05:26:27 +0000 (22:26 -0700)]
Merge branch 'sfc-rx-vlan-filtering'
Edward Cree says:
====================
sfc: RX VLAN filtering
Adds support for VLAN-qualified receive filters on EF10 hardware.
This is needed when running as a guest if the hypervisor has enabled
vfs-vlan-restrict, in which case the firmware rejects filters not qualified
with VLAN 0.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:52:08 +0000 (17:52 +0100)]
sfc: Fix VLAN filtering feature if vPort has VLAN_RESTRICT flag
If vPort has VLAN_RESTRICT flag, VLAN tagged traffic will not be
delivered without corresponding Rx filters which may be proxied to and
moderated by hypervisor.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Habets [Wed, 15 Jun 2016 16:51:07 +0000 (17:51 +0100)]
sfc: VLAN filters must only be created if the firmware supports this.
If it is not supported we simply disable the feature.
For the feature to work we need firmware filter support for
OUTER_VID + LOC_MAC and for OUTER_VID + LOC_MAC_IG.
The low-latency firmware can match on OUTER_VID + LOC_MAC but not on
OUTER_VID + LOC_MAC_IG.
For the capture packet firmware it is the other way around.
Only the full-feature variant can match on both combinations.
Incorporates a fix by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
in the net_dev->[hw_]features handling.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:49:30 +0000 (17:49 +0100)]
sfc: Fix dup unknown multicast/unicast filters after datapath reset
Filter match flags are not unique criteria to be mapped to priority
because of both unknown unicast and unknown multicast are mapped to
LOC_MAC_IG. So, local MAC is required to map filter to priority.
MCDI filter flags is unique criteria to find filter priority.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree [Wed, 15 Jun 2016 16:49:05 +0000 (17:49 +0100)]
sfc: Refactor checks for invalid filter ID
Nearly every time we call efx_ef10_filter_remove_unsafe, we first check
for EFX_EF10_FILTER_ID_INVALID, in which case we do nothing. So move
that check into the function, simplifying all the call sites.
Also, change the return type to void, since none of the callers check it.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Habets [Wed, 15 Jun 2016 16:48:49 +0000 (17:48 +0100)]
sfc: Take mac_lock before calling efx_ef10_filter_table_probe
When trying to enslave an SFC interface to a bond the following BUG_ON was
hit:
kernel BUG [in ef10.c]!
CPU: 0 PID: 4383 Comm: ifenslave Tainted: G
...
Call Trace:
efx_ef10_filter_add_vlan+0x121/0x180 [sfc]
efx_ef10_filter_table_probe+0x2a2/0x4f0 [sfc]
efx_ef10_set_mac_address+0x370/0x6d0 [sfc]
efx_set_mac_address+0x7d/0x120 [sfc]
dev_set_mac_address+0x43/0xa0
bond_enslave+0x337/0xea0 [bonding]
This comes from function efx_ef10_filter_vlan_sync_rx_mode.
To solve the bug we ensure the mac_lock is taken before calling
efx_ef10_filter_add_vlan. But to avoid a priority inversion mac_lock must
be taken before filter_sem.
To satisfy these requirements we end up taking mac_lock in
efx_ef10_vport_set_mac_address, efx_ef10_set_mac_address,
efx_ef10_sriov_set_vf_vlan and efx_probe_filters.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:45:56 +0000 (17:45 +0100)]
sfc: Store unicast and multicast promisc flag with address cache
These flags are built when address cache is updated.
The information will be required when VLAN filtering is added and address
cache is used without re-sync.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:45:36 +0000 (17:45 +0100)]
sfc: Move filter IDs to per-VLAN data structure
It is a step to support VLAN filtering in HW.
Until then, there is only one struct efx_ef10_filter_vlan per struct
efx_ef10_filter_table, with no VLAN information yet.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:44:20 +0000 (17:44 +0100)]
sfc: Forget filter ID when the filter is marked old
It is required to remove setting of filter IDs to invalid from multicast
and unicast addresses caching functions.
Add initialization to invalid when filter table is created.
Add paranoid checks to track consistency.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Rybchenko [Wed, 15 Jun 2016 16:43:00 +0000 (17:43 +0100)]
sfc: Move last mc_promisc flag to EF10 filter table state
It is used for EF10 only and logically belongs to EF10 filter table state.
It is OK that it is reset to false on filter table recreation since all
filters are removed on destruction.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Jun 2016 05:22:17 +0000 (22:22 -0700)]
Merge tag 'rxrpc-rewrite-20160615' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Rework endpoint record handling
Here's the next part of the AF_RXRPC rewrite. In this set I rework
endpoint record handling. There are two types of endpoint record, local
and peer. The local endpoint record is used as an anchor for the transport
socket that AF_RXRPC uses (at the moment a UDP socket). Local endpoints
can be shared between AF_RXRPC sockets under certain restricted
circumstances.
The peer endpoint is a record of the remote end. It is (or will be) used
to keep track MTU and RTT values and, with these changes, is used to find
the call(s) to abort when a network error occurs.
The following significant changes are made:
(1) The local endpoint event handling code is split out into its own file.
(2) The local endpoint list bottom half-excluding spinlock is removed as
things are arranged such that sk_user_data will not change whilst the
transport socket callbacks are in progress.
(3) Local endpoints can now only be shared if they have the same transport
address (as before) and have a local service ID of 0 (ie. they're not
listening for incoming calls). This prevents callbacks from a server
to one process being picked up by another process.
(4) Local endpoint destruction is now accomplished by the same work item
as processes events, meaning that the destructor doesn't need to wait
for the event processor.
(5) Peer endpoints are now held in a hash table rather than a flat list.
(6) Peer endpoints are now destroyed by RCU rather than by work item.
(7) Peer endpoints are now differentiated by local endpoint and remote
transport port in addition to remote transport address and transport
type and family.
This means that a firewall that excludes access between a particular
local port and remote port won't cause calls to be aborted that use a
different port pair.
(8) Error report handling now no longer assumes that the source is always
an IPv4 ICMP message from a UDP port and has assumptions that an ICMP
message comes from an IPv4 socket removed. At some point IPv6 support
will be added.
(9) Peer endpoints rather than local endpoints are now the anchor point
for distributing network error reports.
(10) Both types of endpoint records are now disposed of as soon as all
references to them are gone. There is less hanging around and once
their usage counts hit zero, records can no longer be resurrected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 16 Jun 2016 04:44:33 +0000 (21:44 -0700)]
Merge branch 'liquidio-next'
Raghu Vatsavayi says:
====================
liquidio: Updates and Bug fixes
Following are updates for liquidio bug fixes and driver
support for new firmware interface. These updates are divided
into smaller logical patches as mentioned by you. These set of
nine patches should be applied in the following order as some of
them depend on earlier patches in the list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 14 Jun 2016 23:29:15 +0000 (16:29 -0700)]
ila: Fix checksum neutral mapping
The algorithm for checksum neutral mapping is incorrect. This problem
was being hidden since we were previously always performing checksum
offload on the translated addresses and only with IPv6 HW csum.
Enabling an ILA router shows the issue.
Corrected algorithm:
old_loc is the original locator in the packet, new_loc is the value
to overwrite with and is found in the lookup table. old_flag is
the old flag value (zero of CSUM_NEUTRAL_FLAG) and new_flag is
then (old_flag ^ CSUM_NEUTRAL_FLAG) & CSUM_NEUTRAL_FLAG.
Need SUM(new_id + new_flag + diff) == SUM(old_id + old_flag) for
checksum neutral translation.
If old_flag is set
old_flag - new_flag = old_flag = CSUM_NEUTRAL_FLAG
Else
old_flag - new_flag = -new_flag = ~CSUM_NEUTRAL_FLAG
Tested:
- Implemented a user space program that creates random addresses
and random locators to overwrite. Compares the checksum over
the address before and after translation (must always be equal)
- Enabled ILA router and showed proper operation.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: ipv4: Add ability to have GRE ignore DF bit in IPv4 payloads
In the presence of firewalls which improperly block ICMP Unreachable
(including Fragmentation Required) messages, Path MTU Discovery is
prevented from working.
A workaround is to handle IPv4 payloads opaquely, ignoring the DF bit--as
is done for other payloads like AppleTalk--and doing transparent
fragmentation and reassembly.
Redux includes the enforcement of mutual exclusion between this feature
and Path MTU Discovery as suggested by Alexander Duyck.
Cc: Alexander Duyck <alexander.duyck@gmail.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 14 Jun 2016 18:37:21 +0000 (11:37 -0700)]
net: vrf: Switch dst dev to loopback on device delete
Attempting to delete a VRF device with a socket bound to it can stall:
unregister_netdevice: waiting for red to become free. Usage count = 1
The unregister is waiting for the dst to be released and with it
references to the vrf device. Similar to dst_ifdown switch the dst
dev to loopback on delete for all of the dst's for the vrf device
and release the references to the vrf device.
Fixes: 193125dbd8eb2 ("net: Introduce VRF device driver") Fixes: 35402e3136634 ("net: Add IPv6 support to VRF device") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 14 Jun 2016 10:03:17 +0000 (12:03 +0200)]
mdio: mux: avoid 'maybe-uninitialized' warning
The latest changes to the MDIO code introduced a false-positive
warning with gcc-6 (possibly others):
drivers/net/phy/mdio-mux.c: In function 'mdio_mux_init':
drivers/net/phy/mdio-mux.c:188:3: error: 'parent_bus_node' may be used uninitialized in this function [-Werror=maybe-uninitialized]
It's easy to avoid the warning by making sure the parent_bus_node
is initialized in both cases at the start of the function, since
the later 'of_node_put()' call is also valid for a NULL pointer
argument.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: f20e6657a875 ("mdio: mux: Enhanced MDIO mux framework for integrated multiplexers") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David can you please pick-up this patch-serie for your net-next tree?
Thanks in advance.
This patch series introduces the ndisc ops callback structure to add different
handling for IPv6 neighbour discovery cache functionality. It implements at first
the two following use-cases:
- 6CO handling as userspace option (For all 6LoWPAN layers, BTLE/802.15.4) [0]
- short address handling for 802.15.4 6LoWPAN only [1]
Since my last patch series, I completely changed the whole ndisc_ops callback
structure to not replace the whole ndisc functionality at recv/send level of
NS/NA/RS/RA which I send in my previous patch-series "6lowpan: introduce basic
6lowpan-nd". I changed it now to add different handling in a very low-level way
of ndisc functionality.
The ndisc_ops don't must be registered to dev->ndisc_ops anymore, if they are not
set, then no additional ipv6 ndisc handling will be done.
This patch series now introduce a complete handling of short address for
802.15.4 6LoWPAN in case of send/recv of NA/NS/RS and RA. In case of RA
(receive only) and PIO we also need a second prefix + short-address based
address.
This callback structure can be used later (I hope) for RFC 6775 [0]. This RFC
defines some new option fields and messages for 6LoWPAN-ND. This patch series
does not implement RFC 6775 (except we decide now to handle 6CO in userspace).
Additional we can use the current ops for parse/fill ndisc options for kernel
handled ndisc messages to add 6CIO, see [2].
I tested RA/NS/NA/RS messages with short address which seems to work, what I
didn't test is the redirect messages since I don't know how to generate them.
The short address for redirect messages are also some special case here, because
the short address by a L3 target address lookuped by neighbour cache need to be
added.
btw:
According to [3] sending redirect messages should be also disabled by default
on 6lowpan interfaces, but can be activated afterwards. This is maybe
something for the ipv6_devconf structure. There is a "accept_redirects" but
no "disable_redirects".
changes since v3:
- add acked-by and reviewed-by tags
- fix url references in cover-letter
- add cover-letter that this patch series is okay to go through net-next tree
changes since RFC:
- add lowlevel functions __ndisc_opt_addr_space,
__ndisc_opt_addr_data and __ndisc_fill_addr_option for corresponding
functions which doesn't requires net_device argument.
- move ndisc_ops e.g. ndisc_ops_fill_addr_option function call into the
corresponding device argument function ndisc_fill_addr_option.
(Introduced a special static inline function for redirect handling).
- fix error handling in addrconf_prefix_rcv_add_addr.
(Please see, introduce new API handling that second address registration
(in case of 802.15.4 6LoWPAN) will still be notified if failed, because
dev->addr was successful.
- add ieee802154 sub-directory in short address entry for 6lowpan UAPI.
- add lowpan_802154_is_valid_src_short_addr, because 802.15.4 6lowpan
defines the first bit as multicast (don't know how this can be working
at the end, because some hardware addresses will handle such addresses
in L2 as unicast. See:
https://www.iana.org/assignments/_6lowpan-parameters/_6lowpan-parameters.xhtml#_6lowpan-parameters-2
changes since v2:
- Introduce ndisc_ops to have our own implementation for dealing with NS/NA
which allows also to support RFC6775 (e.g. ARO).
- add handling for handling 6CO as userspace option for RA messages in
case of 6LoWPAN interfaces.
- change lowpan_is_ll to check on linklayer type only.
- added some reviewed-by's.
- move short addr slaac to net/6lowpan instead ipv6 handling.
- add handling for context based address compression in case for
short address as link-layer address.
- change strategy to use short address, a short address will always be used
when it's available.
- Handle override flag in NA messages to update short address information or
not.
====================
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:27 +0000 (21:20 +0200)]
6lowpan: add support for 802.15.4 short addr handling
This patch adds necessary handling for use the short address for
802.15.4 6lowpan. It contains support for IPHC address compression
and new matching algorithmn to decide which link layer address will be
used for 802.15.4 frame.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:26 +0000 (21:20 +0200)]
6lowpan: add support for getting short address
In case of sending RA messages we need some way to get the short address
from an 802.15.4 6LoWPAN interface. This patch will add a temporary
debugfs entry for experimental userspace api.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:25 +0000 (21:20 +0200)]
6lowpan: introduce 6lowpan-nd
This patch introduce different 6lowpan handling for receive and transmit
NS/NA messages for the ipv6 neighbour discovery. The first use-case is
for supporting 802.15.4 short addresses inside the option fields and
handling for RFC6775 6CO option field as userspace option.
Cc: David S. Miller <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:24 +0000 (21:20 +0200)]
ipv6: export several functions
This patch exports some neighbour discovery functions which can be used
by 6lowpan neighbour discovery ops functionality then.
Cc: David S. Miller <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:23 +0000 (21:20 +0200)]
ipv6: introduce neighbour discovery ops
This patch introduces neighbour discovery ops callback structure. The
idea is to separate the handling for 6LoWPAN into the 6lowpan module.
These callback offers 6lowpan different handling, such as 802.15.4 short
address handling or RFC6775 (Neighbor Discovery Optimization for IPv6
over 6LoWPANs).
Cc: David S. Miller <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:22 +0000 (21:20 +0200)]
addrconf: put prefix address add in an own function
This patch moves the functionality to add a RA PIO prefix generated
address in an own function. This move prepares to add a hook for
adding a second address for a second link-layer address. E.g. short
address for 802.15.4 6LoWPAN.
Cc: David S. Miller <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:21 +0000 (21:20 +0200)]
ndisc: add __ndisc_fill_addr_option function
This patch adds __ndisc_fill_addr_option as low-level function for
ndisc_fill_addr_option which doesn't depend on net_device parameter.
Cc: David S. Miller <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:20 +0000 (21:20 +0200)]
ndisc: add __ndisc_opt_addr_data function
This patch adds __ndisc_opt_addr_data as low-level function for
ndisc_opt_addr_data which doesn't depend on net_device parameter.
Cc: David S. Miller <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:19 +0000 (21:20 +0200)]
ndisc: add __ndisc_opt_addr_space function
This patch adds __ndisc_opt_addr_space as low-level function for
ndisc_opt_addr_space which doesn't depend on net_device parameter.
Cc: David S. Miller <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:18 +0000 (21:20 +0200)]
6lowpan: remove ipv6 module request
Since we use exported function from ipv6 kernel module we don't need to
request the module anymore to have ipv6 functionality.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Wed, 15 Jun 2016 19:20:17 +0000 (21:20 +0200)]
6lowpan: add 802.15.4 short addr slaac
This patch adds the autoconfiguration if a valid 802.15.4 short address
is available for 802.15.4 6LoWPAN interfaces.
Cc: David S. Miller <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com> Signed-off-by: Alexander Aring <aar@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log