mmc_remove_host() will cause the mmc core to switch off the bus power by
eventually calling pxamci_set_ios(). This function uses the regulator or
the GPIO which have been freed already.
a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The use of urb->actual_length to update tx_outstanding_bytes
implicitly assumes that the number of bytes actually written is the
same as the number of bytes we tried to write. On error that
assumption is violated so just use transfer_buffer_length the number
of bytes we intended to write to the device.
If an error occurs we need to fall through and call
usb_serial_port_softint to wake up processes waiting in
tty_wait_until_sent.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- fixed shared interrupt bug reported by Vadim Lobanov
- fixed possible warning oops on driver unload when connected
- prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0")
when using gadget ether
Signed-off-by: Thomas Dahlmann <dahlmann.thomas@arcor.de> Cc: Robert Richter <robert.richter@amd.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver incorrectly cancels the mass-storage device CSW request
(which leads to device reset) due to giving back URB at the head of
endpoint's queue after sending each STALL handshake; stop doing that
and start checking for the queue being non-empty before stalling an
endpoint and disallowing stall in such case in musb_gadget_set_halt()
like the other gadget drivers do.
Moreover, the driver starts Rx request despite of the endpoint being
halted -- fix this by moving the SendStall bit check from musb_g_rx()
to rxstate(). And we also sometimes get into rxstate() with DMA still
active after clearing an endpoint's halt (not clear why), so bail out
in this case, similarly to what txstate() does...
While at it, also do the following changes :
- in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the
driver does not allow stalling with non-empty Tx FIFO anyway);
- in rxstate(), stop pointlessly zeroing the 'csr' variable;
- in musb_gadget_set_halt(), move the 'done' label to a more proper
place;
- in musb_g_rx(), eliminate the 'done' label completely...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1304) fixes a regression in ehci-hcd. Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.
The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake. In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found. In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.
Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests. Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Javier Kohen <jkohen@users.sourceforge.net> CC: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"[CPUFREQ] cpumask: avoid playing with cpus_allowed in speedstep-ich.c"
changed the code to mistakenly pass the current cpu as the "processor"
argument of speedstep_get_frequency(), whereas it should be the type of
the processor.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Dominik Brodowski <linux@brodo.de> Reported-by: Dave Mueller <dave.mueller@gmx.ch> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ipv4 ip_frag_reasm(), fully replace 'dev_net(dev)' with 'net', defined
previously patched into 2.6.29.
Between 2.6.28.10 and 2.6.29, net/ipv4/ip_fragment.c was patched,
changing from dev_net(dev) to container_of(...). Unfortunately the goto
section (out_fail) on oversized packets inside ip_frag_reasm() didn't
get touched up as well. Oversized IP packets cause a NULL pointer
dereference and immediate hang.
I discovered this running openvasd and my previous email on this is
titled: NULL pointer dereference at 2.6.32-rc8:net/ipv4/ip_fragment.c:566
Signed-off-by: David Ford <david@blue-labs.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Hauppauge WinTV HVR-1150 retail boards require the FORCE_TS_VALID bit
to be set in order to function properly. This change will work on the early
revisions on the board as well, but the final revision will not function
without this change.
When FORCE_TS_VALID mode is enabled, the saa713x will accept MPEG TS input
without requiring TS_VALID set high. This is required for some new boards
to function properly, due to the hardware design implementation.
The configuration is toggled within the board setup configuration. Boards
that do not have this bit set will function as before with no change.
> We allocate and zero cpu_isolated_map after the isolcpus
> __setup option has run. This means cpu_isolated_map always
> ends up empty and if CPUMASK_OFFSTACK is enabled we write to a
> cpumask that hasn't been allocated.
I introduced this regression in 49557e620339cb13 (sched: Fix
boot crash by zalloc()ing most of the cpu masks).
Use the bootmem allocator if they set isolcpus=, otherwise
allocate and zero like normal.
Reported-by: Anton Blanchard <anton@samba.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: peterz@infradead.org Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <200912021409.17013.rusty@rustcorp.com.au> Signed-off-by: Ingo Molnar <mingo@elte.hu> Tested-by: Anton Blanchard <anton@samba.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
`>>' has a higher precedence than `?' so src2 evaluated to
either 16 or 0 dependent on the bits set in rs2.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Page buffers containing packets with an incorrect checksum or using a
protocol not handled by hardware checksum offload were previously not
passed to LRO. The conversion to GRO changed this, but did not set
the ip_summed value accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify bonding hash transmit policies to use the psource MAC address of
the packet instead of the MAC address configured for the bonding device.
The old sitation conflicts with the documentation.
Signed-off-by: Jasper Spaans <spaans@fox-it.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On UDP sockets, we must call skb_free_datagram() with socket locked,
or risk sk_forward_alloc corruption. This requirement is not respected
in SUNRPC.
Add a convenient helper, skb_free_datagram_locked() and use it in SUNRPC
Reported-by: Francis Moreau <francis.moro@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pedit will reject a policy that is large because it
uses the wrong structure in the policy validation.
This fixes it.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If ace_load_firmware() fails, ace_init() cleans up but still returns
0, leading to an oops as seen in <http://bugs.debian.org/521383>.
It should pass the error code up.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
udp_poll() can in some circumstances drop frames with incorrect checksums.
Problem is we now have to lock the socket while dropping frames, or risk
sk_forward corruption.
This bug is present since commit 95766fff6b9a78d1
([UDP]: Add memory accounting.)
While we are at it, we can correct ioctl(SIOCINQ) to also drop bad frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The VIDIOC_G_STD ioctl may not be present in the case of radio receivers.
In that case G_STD will return an error. The v4l1-compat layer should not
attempt to propagate that error to the caller, instead it should be
ignored.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In commit 0de51088e6a82bc8413d3ca9e28bbca2788b5b53, we introduced the
use of acpi-cpufreq on VIA/Centaur CPU's by removing a vendor check for
VENDOR_INTEL. However, as it turns out, at least the Nano CPU's also
need the PDC (processor driver capabilities) handshake in order to
activate the methods required for acpi-cpufreq.
Since arch_acpi_processor_init_pdc() contains another vendor check for
Intel, the PDC is not initialized on VIA CPU's. The resulting behavior
of a current mainline kernel on such systems is: acpi-cpufreq
loads and it indicates CPU frequency changes. However, the CPU stays at
a single frequency
This trivial patch ensures that init_intel_pdc() is called on Intel and
VIA/Centaur CPU's alike.
Signed-off-by: Harald Welte <HaraldWelte@viatech.com> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As shown in http://thread.gmane.org/gmane.linux.kernel.wireless.general/36497,
mac80211 has a bug that allows a call to the TX routine after the queues have
been stopped. This situation will only occur under extreme stress. Although
b43 does not crash when this condition occurs, it does generate a WARN_ON and
also logs a queue overrun message. This patch recognizes b43 is not at fault
and logs a message only when the most verbose debugging mode is enabled. In
the unlikely event that the queue is not stopped when the DMA queue becomes
full, then a warning is issued.
During testing of this patch with one output stream running repeated tcpperf
writes and a second running a flood ping, this routine was entered with
the DMA ring stopped about once per hour. The condition where the DMA queue is
full but the ring has not been stopped has never been seen by me.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Cc: Michael Buesch <mb@bu3sch.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lennert Buytenhek noticed that delBA handling in mac80211
was broken and has remotely triggerable problems, some of
which are due to some code shuffling I did that ended up
changing the order in which things were done -- this was
mac80211: A-MPDU Tx add delBA from recipient support
The first problem is that I moved a BUG_ON before various
checks -- thereby making it possible to hit. As the comment
indicates, the BUG_ON can be removed since the ampdu_action
callback must already exist when the state is != IDLE.
The second problem isn't easily exploitable but there's a
race condition due to unconditionally setting the state to
OPERATIONAL when a delBA frame is received, even when no
aggregation session was ever initiated. All the drivers
accept stopping the session even then, but that opens a
race window where crashes could happen before the driver
accepts it. Right now, a WARN_ON may happen with non-HT
drivers, while the race opens only for HT drivers.
For this case, there are two things necessary to fix it:
1) don't process spurious delBA frames, and be more careful
about the session state; don't drop the lock
2) HT drivers need to be prepared to handle a session stop
even before the session was really started -- this is
true for all drivers (that support aggregation) but
iwlwifi which can be fixed easily. The other HT drivers
(ath9k and ar9170) are behaving properly already.
Reported-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lennert Buytenhek noticed a remotely triggerable problem
in mac80211, which is due to some code shuffling I did
that ended up changing the order in which things were
done -- this was in
When we get a stream suspend event force the power down since otherwise
the stream would remain marked as active. In future we'll probably want
to make this stream-specific and add an interface to make the power down
of other widgets optional in order to support leaving bypass paths
active while suspending the processor.
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com> Tested-by: Joonyoung Shim <jy0922.shim@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
also holds for fuse_create, however, the same kind of check was missing there.
As an impact of this bug, open(newfile, O_RDWR|O_CREAT|O_DIRECT) fails, but a
stub newfile will remain if the fuse server handled the implied FUSE_CREATE
request appropriately.
Other impact: in the above situation ima_file_free() will complain to open/free
imbalance if CONFIG_IMA is set.
Changeset a65318bf3afc93ce49227e849d213799b072c5fd (NFSv4: Simplify some
cache consistency post-op GETATTRs) incorrectly changed the getattr
bitmap for readdir().
This causes the readdir() function to fail to return a
fileid/inode number, which again exposed a bug in the NFS readdir code that
causes spurious ENOENT errors to appear in applications (see
http://bugzilla.kernel.org/show_bug.cgi?id=14541).
The immediate band aid is to revert the incorrect bitmap change, but more
long term, we should change the NFS readdir code to cope with the
fact that NFSv4 servers are not required to support fileids/inode numbers.
While running fsstress tests on the NFSv4 mounted ext3 and ext4
filesystem, the following call trace was generated on the nfs
server machine.
Replace GFP_KERNEL with GFP_NOFS in ima_iint_insert() to avoid a
potential deadlock.
=================================
[ INFO: inconsistent lock state ]
2.6.31-31.el6.x86_64 #1
---------------------------------
inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
kswapd2/75 [HC0[0]:SC0[0]:HE1:SE1] takes:
(jbd2_handle){+.+.?.}, at: [<ffffffff811edd5e>] jbd2_journal_start+0xfe/0x13f
{RECLAIM_FS-ON-W} state was registered at:
[<ffffffff81091e40>] mark_held_locks+0x65/0x99
[<ffffffff81091f31>] lockdep_trace_alloc+0xbd/0xf5
[<ffffffff81126fdd>] kmem_cache_alloc+0x40/0x185
[<ffffffff812344d7>] ima_iint_insert+0x3d/0xf1
[<ffffffff812345b0>] ima_inode_alloc+0x25/0x44
[<ffffffff811484ac>] inode_init_always+0xec/0x271
[<ffffffff81148682>] alloc_inode+0x51/0xa1
[<ffffffff81148700>] new_inode+0x2e/0x94
[<ffffffff811b2f08>] ext4_new_inode+0xb8/0xdc9
[<ffffffff811be611>] ext4_create+0xcf/0x175
[<ffffffff8113e2cd>] vfs_create+0x82/0xb8
[<ffffffff8113f337>] do_filp_open+0x32c/0x9ee
[<ffffffff811309b9>] do_sys_open+0x6c/0x12c
[<ffffffff81130adc>] sys_open+0x2e/0x44
[<ffffffff81011e42>] system_call_fastpath+0x16/0x1b
[<ffffffffffffffff>] 0xffffffffffffffff
irq event stamp: 90371
hardirqs last enabled at (90371): [<ffffffff8112708d>]
kmem_cache_alloc+0xf0/0x185
hardirqs last disabled at (90370): [<ffffffff81127026>]
kmem_cache_alloc+0x89/0x185
softirqs last enabled at (89492): [<ffffffff81068ecf>]
__do_softirq+0x1bf/0x1eb
softirqs last disabled at (89477): [<ffffffff8101312c>] call_softirq+0x1c/0x30
other info that might help us debug this:
2 locks held by kswapd2/75:
#0: (shrinker_rwsem){++++..}, at: [<ffffffff810f98ba>] shrink_slab+0x44/0x177
#1: (&type->s_umount_key#25){++++..}, at: [<ffffffff811450ba>]
Reported-by: Muni P. Beerakam <mbeeraka@in.ibm.com> Reported-by: Amit K. Arora <amitarora@in.ibm.com> Signed-off-by: Mimi Zohar <zohar@us.ibm.com> Signed-off-by: James Morris <jmorris@namei.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When 802.11g was introduced, we had RTS/CTS and CTS-to-Self protection
mechanisms. In an HT Beacon, HT stations use the "Operating Mode" field
in the HT Information Element to determine whether or not to use
protection.
The Operating Mode field has 4 possible settings: 0-3:
Mode 0: If all stations in the BSS are 20/40 MHz HT capable, or if the
BSS is 20/40 MHz capable, or if all stations in the BSS are 20 MHz HT
stations in a 20 MHz BSS
Mode 1: used if there are non-HT stations or APs using the primary or
secondary channels
Mode 2: if only HT stations are associated in the BSS and at least one
20 MHz HT station is associated.
Mode 3: used if one or more non-HT stations are associated in the BSS.
When in operating modes 1 or 3, and the Use_Protection field is 1 in the
Beacon's ERP IE, all HT transmissions must be protected using RTS/CTS or
CTS-to-Self.
By default, CTS-to-self is the preferred protection mechanism for less
overhead and higher throughput; but using the full RTS/CTS will better
protect the inner exchange from interference, especially in
highly-congested environment.
For 6000 series WIFI NIC, RTS/CTS protection mechanism is the
recommended choice for HT traffic based on the HW design.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scratchpad_free() function uses xhci->page_size to free some memory
with pci_free_consistent(). However, the page_size is set to zero before
the call, causing kernel oopses on driver unload. Call scratchpad_free()
before setting xhci->page_size to zero.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: John Youn <John.Youn@synopsys.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The trb_in_td() function in the xHCI driver is supposed to translate a
physical transfer buffer request (TRB) into a virtual pointer to the ring
segment that TRB is in.
Unfortunately, a mistake in this function may cause endless loops as the
driver searches through the linked list of ring segments over and over
again. Fix a couple bugs that may lead to loops or bad output:
1. Bail out if we get a NULL pointer when translating the segment's
private structure and the starting DMA address of the segment chunk. If
this happens, we've been handed a starting TRB pointer from a different
ring.
2. Make sure the function works when there's multiple segments in the
ring. In the while loop to search through the ring segments, use the
current segment variable (cur_seg), rather than the starting segment
variable (start_seg) that is passed in.
3. Stop searching the ring if we've run through all the segments in the
ring.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the xHCI driver fails during the memory initialization, xhci->ir_set
may not be a valid pointer. Check that it points to valid DMA'able memory
before writing to that address during the memory freeing process.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be
switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
This patch (as1299b) fixes a bug in an error-handling path of usbmon's
binary interface. The storage area for URB data is divided into
fixed-size blocks. If an URB's data can't be copied, the area
reserved for it should be decreased to the size of the truncated
information (rounded up to a block boundary). Rounding up the amount
to be removed and subtracting it from the reserved size is definitely
the wrong thing to do.
Also, when the data for an isochronous URB can't be copied, we can
still copy the isoc packet descriptors. In fact the current code does
copy the descriptors, but then sets the capture length to 0 so they
remain inaccessible. The capture length should be reduced to the
length of the descriptors, not set to 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch in the driver is required to avoid USB 1.1 device
failures that may occur due to requests from USB OHCI controllers may
be overwritten if the latency for any pending request by the USB
controller is very long (in the range of milliseconds).
Signed-off-by: Libin Yang <libin.yang@amd.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=2
9a68e39d4a701fb3be03cae9b462408664ebd205 broke carrier handling so that a
cp210x setup which needed the carrier lines set up (non CLOCAL) which did
not make a call which set the termios bits left the lines down even if
CLOCAL was not asserted.
Fix this not by reverting but by adding the proper dtr_rts and
carrier_raised methods. This both sets the modem lines properly and also
implements the correct blocking semantics for the port as required by
POSIX.
Signed-off-by: Alan Cox <alan@linux.intel.com> Reported-by: Karl Hiramoto <karl@hiramoto.org> Tested-by: Karl Hiramoto <karl@hiramoto.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=2
The tty_port code inherited a bug common to various drivers it was based
upon. If the tty is opened O_NONBLOCK we do not wait for the carrier to be
raised but we must still raise our modem lines if appropriate.
(There is a second question here about whether we should do so if CLOCAL is
set but that can wait)
Signed-off-by: Alan Cox <alan@linux.intel.com> Reported-by: Karl Hiramoto <karl@hiramoto.org> Tested-by: Karl Hiramoto <karl@hiramoto.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a direct reclaim makes no forward progress, it considers whether it
should go OOM or not. Whether OOM is triggered or not, it may retry the
allocation afterwards. In times past, this would always wake kswapd as
well but currently, kswapd is not woken up after direct reclaim fails.
For order-0 allocations, this makes little difference but if there is a
heavy mix of higher-order allocations that direct reclaim is failing for,
it might mean that kswapd is not rewoken for higher orders as much as it
did previously.
This patch wakes up kswapd when an allocation is being retried after a
direct reclaim failure. It would be expected that kswapd is already
awake, but this has the effect of telling kswapd to reclaim at the higher
order as well.
Signed-off-by: Mel Gorman <mel@csn.ul.ie> Reviewed-by: Christoph Lameter <cl@linux-foundation.org> Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 341ce06f69abfafa31b9468410a13dbd60e2b237 ("page allocator:
calculate the alloc_flags for allocation only once") altered watermark
logic slightly by allowing rt_tasks that are handling an interrupt to set
ALLOC_HARDER. This patch brings the watermark logic more in line with
2.6.30.
This change results in a reduction of the number high-order GFP_ATOMIC
allocation failures reported. See
http://www.gossamer-threads.com/lists/linux/kernel/1144153
[rientjes@google.com: Spotted the problem] Signed-off-by: Mel Gorman <mel@csn.ul.ie> Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi> Reviewed-by: Rik van Riel <riel@redhat.com> Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Lezcano reported a leak in 'struct pid' and 'struct pid_namespace'
that is discussed in:
http://lkml.org/lkml/2009/10/2/159.
To summarize the thread, when container-init is terminated, it sets the
PF_EXITING flag, zaps other processes in the container and waits to reap
them. As a part of reaping, the container-init should flush any /proc
dentries associated with the processes. But because the container-init is
itself exiting and the following PF_EXITING check, the dentries are not
flushed, resulting in leak in /proc inodes and dentries.
This fix reverts the commit 7766755a2f249e7e0 ("Fix /proc dcache deadlock
in do_exit") which introduced the check for PF_EXITING. At the time of
the commit, shrink_dcache_parent() flushed dentries from other filesystems
also and could have caused a deadlock which the commit fixed. But as
pointed out by Eric Biederman, after commit 0feae5c47aabdde59,
shrink_dcache_parent() no longer affects other filesystems. So reverting
the commit is now safe.
As pointed out by Jan Kara, the leak is not as critical since the
unclaimed space will be reclaimed under memory pressure or by:
echo 3 > /proc/sys/vm/drop_caches
But since this check is no longer required, its best to remove it.
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com> Reported-by: Daniel Lezcano <dlezcano@fr.ibm.com> Acked-by: Eric W. Biederman <ebiederm@xmission.com> Acked-by: Jan Kara <jack@ucw.cz> Cc: Andrea Arcangeli <andrea@cpushare.com> Cc: Serge Hallyn <serue@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For FS_IOC_RESVSP and FS_IOC_RESVSP64 compat_sys_ioctl() uses its
arg argument as a pointer to userspace. However it is missing a
a call to compat_ptr() which will do a proper pointer conversion.
This was introduced with 3e63cbb1 "fs: Add new pre-allocation ioctls
to vfs for compatibility with legacy xfs ioctls".
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ankit Jain <me@ankitjain.org> Acked-by: Christoph Hellwig <hch@lst.de> Cc: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Arnd Bergmann <arndbergmann@googlemail.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
v3020_mmio_read_bit() always returns 0 when left_shift > 7.
v3020_mmio_read_bit()'s return type is (unsigned char). The code returns
a value masked by (1 << left_shift) that is casted to the return type. If
left_shift is larger than 7, the cast will always result in a 0 return
value. The problem was discovered with left_shift = 16, and the included
patch corrects the problem.
The bug was introduced in the last (Apr 3 2009) commit of the file, kernel
versions 2.6.30 and later.
PPS events must be recorded according to PPS's mode settings.
If a process asks for (i.e.) capture-assert events only, when the PPS
client calls the pps_event() function to save the current PPS event, we
should verify the event type and then discard unwanted ones.
Also, without this patch userland processes waiting for a specific PPS
event (assert or clear but not both) may be awakened at wrong time.
Signed-off-by: Rodolfo Giometti <giometti@linux.it> Tested-by: William S. Brasher <billb958@door.net> Tested-by: Reg Clemens <clemens@dwf.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: at lib/debugobjects.c:255 debug_print_object+0x42/0x50()
Hardware name: System Product Name
ODEBUG: init active object type: timer_list
Modules linked in:
Pid: 2619, comm: dmesg Tainted: G W 2.6.32-rc5-tip+ #5298
Call Trace:
[<81035443>] warn_slowpath_common+0x6a/0x81
[<8120e483>] ? debug_print_object+0x42/0x50
[<81035498>] warn_slowpath_fmt+0x29/0x2c
[<8120e483>] debug_print_object+0x42/0x50
[<8120ec2a>] __debug_object_init+0x279/0x2d7
[<8120ecb3>] debug_object_init+0x13/0x18
[<810409d2>] init_timer_key+0x17/0x6f
[<81041526>] free_uid+0x50/0x6c
[<8104ed2d>] put_cred_rcu+0x61/0x72
[<81067fac>] rcu_do_batch+0x70/0x121
debugobjects warns about an enqueued timer being initialized. If
CONFIG_USER_SCHED=y the user management code uses delayed work to
remove the user from the hash table and tear down the sysfs objects.
free_uid is called from RCU and initializes/schedules delayed work if
the usage count of the user_struct is 0. The init/schedule happens
outside of the uidhash_lock protected region which allows a concurrent
caller of find_user() to reference the about to be destroyed
user_struct w/o preventing the work from being scheduled. If the next
free_uid call happens before the work timer expired then the active
timer is initialized and the work scheduled again.
The race was introduced in commit 5cb350ba (sched: group scheduling,
sysfs tunables) and made more prominent by commit 3959214f (sched:
delayed cleanup of user_struct)
Move the init/schedule_delayed_work inside of the uidhash_lock
protected region to prevent the race.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Dhaval Giani <dhaval@linux.vnet.ibm.com> Cc: Paul E. McKenney <paulmck@us.ibm.com> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The s2255 driver had logic which aborted processing of a video frame
if there was no process waiting on the video buffer in question. That
simply doesn't work when the application is doing things in an
asynchronous manner. If the application went to the trouble to queue
the buffer in the first place, then the driver should always attempt
to complete it - even if the application at that moment has its
attention turned elsewhere. Applications which always blocked waiting
for I/O on the capture device would not have been affected by this.
Applications which *mostly* blocked waiting for I/O on the capture
device probably only would have been somewhat affected (frame lossage,
at a rate which goes up as the application blocks less). Applications
which never blocked on the capture device (e.g. polling only) however
would never have been able to receive any video frames, since in that
case this "is anyone waiting on this?" check on the buffer never would
have evalutated true. This patch just deletes that harmful check
against the buffer's wait queue.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixing kernel oops when driver attemps to load xc2028 firmware.
Note by djh: the patch contribute by Martin is a port of a fix I made during
the PCTV 340e development. It's a temporary workaround that fixes a regression
(an OOPS condition) and the real fix should be in the code that manages the
i2c master on the dib7000p. But this fix does address the immmediate
regression and should be merged upstream until we do a cleaner fix.
Because the counters were not reset when starting up streaming, they would
be reused from the previous run. This can result in cases such that when the
second instance of streaming starts up, the "cnt" variable in
em28xx_audio_isocirq() can end up being negative, resulting in attempting to
write to memory before the start of runtime->dma_area (as well as having a
negative number of bytes to copy).
Multiplication by 62500 causes an overflow in the 32 bit freq variable,
which is later divided by 1000 when using FM radio.
This patch prevents the overflow by scaling the frequency value correctly
upfront. Thanks to Henk Vergonet for spotting the problem and providing
a preliminary patch, which this changeset was based upon.
While having tda18271 module set with debug=17 (cal & info prints) and
cal=0 (delay calibration process until first use) - I discovered that
during the calibration process, if the frequency test for 69750000
returned a bcal of 0 (see tda18721-fe.c in tda18271_powerscan func) that
the tuner wouldn't be able to pickup any of the frequencies in the range
(all the other frequencies bands returned bcal=1). I spent some time
going over the code and the NXP's tda18271 spec (ver.4 of it i think) and
adding a lot of debug prints and walking/stepping through the calibration
process. I found that when the powerscan fails to find a frequency, the
rf calibration is not run and the default value is supposed to be used in
its place (pulled from the RF_CAL_map table) - but something was getting
goofed up there.
Now, my c coding skills are very rusty, but i think root of the problem is
a signedness issue with the math operation for calculating the rf_a1 and
rf_a2 values in tda18271_rf_tracking_filters_init func, which results in
values like 20648 for rf_a1 (when it should probably have a value like 0,
or so slightly negative that it should be zero - this bad value for rf_a1
would in turn makes the approx calc within
tda18271c2_rf_tracking_filters_correction go out of whack). The simplest
solution i found was to explicitly convert the signedness of the
denominator to avoid the implicit conversion. The values placed into the
u32 rf_freq array should never exceed about 900mhz, so i think the s32 max
value shouldn't be an issue in this case.
I've tested it out a little, and even when i get a bcal=0 with the
modified code, the default calibration value gets used, rf_a1 is zero, and
the tuner seems to lock on the stream and mythtv seems to play it fine.
Signed-off-by: Seth Barry <seth@cyberseth.com> Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bttv driver function which handles switching of the video standard
(set_tvnorm() in bttv-driver.c) includes a check which can optionally
also reset the cropping configuration to a default value. It is
"optional" based on a comparison of the cropcap parameters of the
previous vs the newly requested video standard. The comparison is
being done with a memcmp(), a function which only returns a true value
if the comparison actually fails.
This if-statement appears to have been written to assume wrong
memcmp() semantics. That is, it was re-initializing the cropping
configuration only if the new video standard did NOT have different
cropcap values. That doesn't make any sense. One definitely should
reset things if the cropcap parameters are different - if there's any
comparison to made at all.
The effect of this problem was that a transition from, say, PAL to
NTSC would leave in place old cropping setup that made sense for the
PAL geometry but not for NTSC. If the application doesn't care about
cropping it also won't try to reset the cropping configuration,
resulting in an improperly cropped video frame. In the case I was
testing this actually caused black video frames to be displayed.
Another interesting effect of this bug is that if one does something
which does NOT change the video standard and this function is run,
then the cropping setup gets reset anyway - again because of the
backwards comparison. It turns out that just running anything which
merely opens and closes the video device node (e.g. v4l-info) will
cause this to happen. One can argue that simply opening the device
node and not doing anything to it should not mess with any of its
state - but because of this behavior, any TV app which does such
things (e.g. xawtv) probably therefore doesn't see the problem.
The solution is to fix the sense of the if-statement. It's easy to
see how this mistake could have been made given how memcmp() works.
The patch is therefore removal of a single "!" character from the
if-statement in set_tvnorm in bttv-driver.c.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a subtle interaction in the bttv driver which can result in
fields being repeatedly processed out of order. This is a problem
specifically when running in V4L2_FIELD_ALTERNATE mode (probably the
most common case).
1. The determination of which fields are associated with which buffers
happens in videobuf, before the bttv driver gets a chance to queue the
corresponding DMA. Thus by the point when the DMA is queued for a
given buffer, the algorithm has to do the queuing based on the
buffer's already assigned field type - not based on which field is
"next" in the video stream.
2. The driver normally tries to queue both the top and bottom fields
at the same time (see bttv_irq_next_video()). It tries to sort out
top vs bottom by looking at the field type for the next 2 available
buffers and assigning them appropriately.
3. However the bttv driver *always* actually processes the top field
first. There's even an interrupt set aside for specifically
recognizing when the top field has been processed so that it can be
marked done even while the bottom field is still being DMAed.
Given all of the above, if one gets into a situation where
bttv_irq_next_video() gets entered when the first available buffer has
been pre-associated as a bottom field, then the function is going to
process the buffers out of order. That first available buffer will be
put into the bottom field slot and the buffer after that will be put
into the top field slot. Problem is, since the top field is always
processed first by the driver, then that second buffer (the one after
the first available buffer) will be the first one to be finished.
Because of the strict fifo handling of all video buffers, then that
top field won't be seen by the app until after the bottom field is
also processed. Worse still, the app will get back the
chronologically later bottom field first, *before* the top field is
received. The buffer's timestamps will even be backwards.
While not fatal to most TV apps, this behavior can subtlely degrade
userspace deinterlacing (probably will cause jitter). That's probably
why it has gone unnoticed. But it will also cause serious problems if
the app in question discards all but the latest received buffer (a
latency minimizing tactic) - causing one field to only ever be
displayed since the other is now always late. Unfortunately once you
get into this state, you're stuck this way - because having consumed
two buffers, now the next time around the "first" available buffer
will again be a bottom field and the same thing happens.
How can we get into this state? In a perfect world, where there's
always a few free buffers queued to the driver, it should be
impossible. However if something disrupts streaming, e.g. if the
userspace app can't queue free buffers fast enough for a moment due
perhaps to a CPU scheduling glitch, then the driver can get
momentarily starved and some number of fields will be dropped. That's
OK. But if an odd number of fields get dropped, then that "first"
available buffer might be the bottom field and now we're stuck...
This patch fixes that problem by deliberately only setting up a single
field for one frame if we don't get a top field as the first available
buffer. By purposely skipping the other field, then we only handle a
single buffer thus bringing things back into proper sync (i.e. top
field first) for the next frame. To do this we just drop the few
lines in bttv_irq_next_video() that attempt to set up the second
buffer when that second buffer isn't for the bottom field.
This is definitely a problem in when in V4L2_FIELD_ALTERNATE mode. In
the other modes this change either has no effect or doesn't harm
things any further anyway.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
d451564 broke ARM by requiring KM_IRQ_PTE, KM_NMI and KM_NMI_PTE to
always be defined. Solve this by providing invalid definitions for
these constants, but only if CONFIG_DEBUG_HIGHMEM is enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Code was added to mm/higmem.c that depends on several
kmap types that powerpc does not support. We add dummy
invalid definitions for KM_NMI, KM_NM_PTE, and KM_IRQ_PTE.
According to list discussion, this fix should not be needed
anymore starting with 2.6.33. The code is commented to this
effect so hopefully we will remember to remove this.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
debug_kmap_atomic() tries to prevent ever printing more than 10
warnings, but it does so by testing whether an unsigned integer
is equal to 0. However, if the warning is caused by a nested
IRQ, then this counter may underflow and the stream of warnings
will never end.
If only the output substream of a RawMIDI device has been opened and
if this device is then opened with O_RDWR | O_APPEND and if the
initialization of the input substream fails (either because of low
memory or because the device driver's open callback fails), then the
runtime structure of the already open output substream will be freed
and all following writes through the first handle will cause
snd_rawmidi_write() to use the NULL runtime pointer.
Commit 9a1b64caac82aa02cb74587ffc798e6f42c6170a in 2.6.30 moved the
substream initialization code to where it would be executed every time
the substream is opened.
This had the consequence that any further opening would drop and leak
the data in the existing buffer, and that the device driver's open
callback would be called multiple times, unexpectedly.
Commit 9a1b64caac82aa02cb74587ffc798e6f42c6170a in 2.6.30 dropped the
check that a substream must already have been opened with O_APPEND to be
able to open it a second time.
This would make it possible for a substream to be switched to append
mode, which would mean that non-atomic writes would fail unexpectedly.
Sending an Active Sensing message when closing a port can interfere with
the following data if the port is reopened and a note-on is sent before
the device's timeout has elapsed. Therefore, it is better to disable
this setting by default.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
In 2.6.23 kernel, commit a32ea1e1f925399e0d81ca3f7394a44a6dafa12c
("Fix read/truncate race") fixed a race in the generic code, and as a
side effect, now do_generic_file_read() can ask us to readpage() past
the i_size. This seems to be correctly handled by the block routines
(e.g. block_read_full_page() fills the page with zeroes in case if
somebody is trying to read past the last inode's block).
JFFS2 doesn't handle this; it assumes that it won't be asked to read
pages which don't exist -- and thus that there will be at least _one_
valid 'frag' on the page it's being asked to read. It will fill any
holes with the following memset:
When the 'closest smaller match' returned by jffs2_lookup_node_frag() is
actually on a previous page and ends before 'offset', that results in:
memset(buf, 0, <huge unsigned negative>);
Hopefully, in most cases the corruption is fatal, and quickly causing
random oopses, like this:
root@10.0.0.4:~/ltp-fs-20090531# ./testcases/kernel/fs/ftest/ftest01
Unable to handle kernel paging request for data at address 0x00000008
Faulting instruction address: 0xc01cd980
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01cd980] rb_insert_color+0x38/0x184
LR [c0043978] enqueue_hrtimer+0x88/0xc4
Call Trace:
[c6c63b60] [c004f9a8] tick_sched_timer+0xa0/0xe4 (unreliable)
[c6c63b80] [c0043978] enqueue_hrtimer+0x88/0xc4
[c6c63b90] [c0043a48] __run_hrtimer+0x94/0xbc
[c6c63bb0] [c0044628] hrtimer_interrupt+0x140/0x2b8
[c6c63c10] [c000f8e8] timer_interrupt+0x13c/0x254
[c6c63c30] [c001352c] ret_from_except+0x0/0x14
--- Exception: 901 at memset+0x38/0x5c
LR = jffs2_read_inode_range+0x144/0x17c
[c6c63cf0] [00000000] (null) (unreliable)
This patch fixes the issue, plus fixes all LTP tests on NAND/UBI with
JFFS2 filesystem that were failing since 2.6.23 (seems like the bug
above also broke the truncation).
Reported-By: Anton Vorontsov <avorontsov@ru.mvista.com> Tested-By: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix combine_word problem where first octet is not
read properly. The only affected place seems to be the
INPUT_TERMINAL type. Before now, sound controls can be created
with the output terminal's name which is a fallback mechanism
used only for unknown input terminal types. For example,
Line can wrongly appear as Speaker. After the change it
should appear as Line.
The side effect of this change can be that users
can expect the wrong control name in their scripts or
programs while now we return the correct one.
Probably, these defines should use get_unaligned_le16 and
friends.
During 'check' of a raid1 or raid10 it is possible for the management
thread to spend a lot of time running 'memcmp' on blocks from
different devices, so make sure the thread has a chance to schedule.
raid5d already has a cond_resched (in process_stripe).
Reported-By: Lee Howard <faxguy@howardsilvan.com> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This value is visible through sysfs and is used by mdadm
when it manages a reshape (backing up data that is about to be
rearranged). So it is important that it is always correct.
Current it does not get updated properly when a reshape
starts which can cause problems when assembling an array
that is in the middle of being reshaped.
If a 'sync_max' has been set (via sysfs), it is wrong to clear it
until a resync (or reshape or recovery ...) actually reached that
point.
So if a resync is interrupted (e.g. by device failure),
leave 'resync_max' unchanged.
This is particularly important for 'reshape' operations that do not
change the size of the array. For such operations mdadm needs to
monitor the reshape taking rolling backups of the section being
reshaped. If resync_max gets cleared, the reshape can get ahead of
mdadm and then the backups that mdadm creates are useless.
As reported by Rick Farina (sidhayn@gmail.com), removing the RTL8187
USB stick, or unloading the driver rtl8187 using rmmod will cause a
kernel oops. There are at least two forms of the failure, (1) BUG:
Scheduling while atomic, and (2) a fatal kernel page fault. This
problem is reported in Bugzilla #14539.
This problem does not occur for kernel 2.6.31, but does for 2.6.32-rc2,
thus it is technically a regression; however, bisection did not locate
any faulty patch. The fix was found by comparing the faulty code in
rtl8187 with p54usb. My interpretation is that the handling of work
queues in mac80211 changed enough to the LEDs to be unregistered
before tasks on the work queues are cancelled. Previously, these
actions could be done in either order.
(Herton Ronaldo Krzesinski <herton@mandriva.com.br> reports that the
code is the same in 2.6.31, so this may be a candidate for 2.6.31.x.
-- JWL)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Rick Farina <sidhayn@gmail.com> Tested-by: Rick Farina <sidhayn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A negative offset could be used to index before the event buffer and
lead to a security breach.
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SMB writes are sent with a starting offset and length. When the server
supports the newer SMB trans2 posix open (rather than using the SMB
NTCreateX) a file can be opened with SMB_O_APPEND flag, and for that
case Samba server assumes that the offset sent in SMBWriteX is unneeded
since the write should go to the end of the file - which can cause
problems if the write was cached (since the beginning part of a
page could be written twice by the client mm). Jeff suggested that
masking the flag on posix open on the client is easiest for the time
being. Note that recent Samba server also had an unrelated problem with
SMB NTCreateX and append (see samba bugzilla bug number 6898) which
should not affect current Linux clients (unless cifs Unix Extensions
are disabled).
The cifs client did not send the O_APPEND flag on posix open
before 2.6.29 so the fix is unneeded on early kernels.
In the future, for the non-cached case (O_DIRECT, and forcedirectio mounts)
it would be possible and useful to send O_APPEND on posix open (for Windows
case: FILE_APPEND_DATA but not FILE_WRITE_DATA on SMB NTCreateX) but for
cached writes although the vfs sets the offset to end of file it
may fragment a write across pages - so we can't send O_APPEND on
open (could result in sending part of a page twice).
Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lookup called during network boot (network root filesystem
for diskless workstation) has case where nd is null in
lookup. This patch fixes that in cifs_lookup.
(Shirish noted that 2.6.30 and 2.6.31 stable need the same check)
Signed-off-by: Shirish Pargaonkar <shirishp@us.ibm.com> Acked-by: Jeff Layton <jlayton@redhat.com> Tested-by: Vladimir Stavrinov <vs@inist.ru> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the commit ec06aedd44 that intended to turn off querying for server inode
numbers when server doesn't consistently support inode numbers. Presumably
the commit didn't actually clear the CIFS_MOUNT_SERVER_INUM flag, perhaps a
typo.
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's possible that a server will return a valid FileID when we query the
FILE_INTERNAL_INFO for the root inode, but then zeroed out inode numbers
when we do a FindFile with an infolevel of
SMB_FIND_FILE_ID_FULL_DIR_INFO.
In this situation turn off querying for server inode numbers, generate a
warning for the user and just generate an inode number using iunique.
Once we generate any inode number with iunique we can no longer use any
server inode numbers or we risk collisions, so ensure that we don't do
that in cifs_get_inode_info either.
Reported-by: Timothy Normand Miller <theosib@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because it's lighter weight, CIFS tries to use CIFSGetSrvInodeNumber to
verify the accessibility of the root inode and then falls back to doing a
full QPathInfo if that fails with -EOPNOTSUPP. I have at least a report
of a server that returns NT_STATUS_INTERNAL_ERROR rather than something
that translates to EOPNOTSUPP.
Rather than trying to be clever with that call, just have
is_path_accessible do a normal QPathInfo. That call is widely
supported and it shouldn't increase the overhead significantly.
Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a kernel oops reported by Markus Trippelsdorf in the email
titled "[NILFS users] kernel Oops while running nilfs_cleanerd".
The oops was caused by a bug of error path in
nilfs_ioctl_move_blocks() function, which was inlined in
nilfs_ioctl_clean_segments().
nilfs_ioctl_move_blocks checks duplication of blocks which will be
moved in garbage collection. But, the check should have be done
within nilfs_ioctl_move_inode_block() to prevent list corruption among
buffers storing the target blocks.
To fix the kernel oops, this moves forward the duplication check
before the list insertion.
I also tested this for stable trees [2.6.30, 2.6.31].
Commit 0c570cdeb8fdfcb354a3e9cd81bfc6a09c19de0c
(PM / yenta: Fix cardbus suspend/resume regression) caused resume to
fail on systems with two CardBus bridges. While the exact nature
of the failure is not known at the moment, it can be worked around by
splitting the yenta resume into an early part, executed during the
early phase of resume, that will only resume the socket and power it
up if there was a card in it during suspend, and a late part,
executed during "regular" resume, that will carry out all of the
remaining yenta resume operations.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=14334, which is a
listed regression from 2.6.31.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> Reported-by: Stephen J. Gowdy <gowdy@cern.ch> Tested-by: Jose Marino <braket@hotmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log