IOMMU table initialized, virtual merging enabled
Interrupt 155954 (real) is invalid, disabling it.
Interrupt 155953 (real) is invalid, disabling it.
ie we took some spurious interrupts. default_machine_crash_shutdown tries
to disable all interrupt sources but uses chip->disable which maps to
the default action of:
static void default_disable(unsigned int irq)
{
}
If we use chip->shutdown, then we actually mask the IRQ:
We wrap the crash_shutdown_handles[] calls with longjmp/setjmp, so if any
of them fault we can recover. The problem is we add a hook to the debugger
fault handler hook which calls longjmp unconditionally.
This first part of kdump is run before we marshall the other CPUs, so there
is a very good chance some CPU on the box is going to page fault. And when
it does it hits the longjmp code and assumes the context of the oopsing CPU.
The machine gets very confused when it has 10 CPUs all with the same stack,
all thinking they have the same CPU id. I get even more confused trying
to debug it.
The patch below adds crash_shutdown_cpu and uses it to specify which cpu is
in the protected region. Since it can only be -1 or the oopsing CPU, we don't
need to use memory barriers since it is only valid on the local CPU - no other
CPU will ever see a value that matches it's local CPU id.
Eventually we should switch the order and marshall all CPUs before doing the
crash_shutdown_handles[] calls, but that is a bigger fix.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kamalesh babulal <kamalesh@linux.vnet.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Robert Swiecki reported a BUG_ON(page_mapped) from a fuzzer, punching
a hole with madvise(,, MADV_REMOVE). That path is under mutex, and
cannot be explained by lack of serialization in unmap_mapping_range().
Reviewing the code, I found one place where vm_truncate_count handling
should have been updated, when I switched at the last minute from one
way of managing the restart_addr to another: mremap move changes the
virtual addresses, so it ought to adjust the restart_addr.
But rather than exporting the notion of restart_addr from memory.c, or
converting to restart_pgoff throughout, simply reset vm_truncate_count
to 0 to force a rescan if mremap move races with preempted truncation.
We have no confirmation that this fixes Robert's BUG,
but it is a fix that's worth making anyway.
We have found a hardware erratum on 82599 hardware that can lead to
unpredictable behavior when Header Splitting mode is enabled. So
we are no longer enabling this feature on affected hardware.
Please see the 82599 Specification Update for more information.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
However the code in rxrpc_instantiate strips it away:
data += sizeof(kver);
datalen -= sizeof(kver);
Removing kif_version fixes my problem.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we get oplock break notification we should set the appropriate
value of OplockLevel field in oplock break acknowledge according to
the oplock level held by the client in this time. As we only can have
level II oplock or no oplock in the case of oplock break, we should be
aware only about clientCanCacheRead field in cifsInodeInfo structure.
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com> Signed-off-by: Steve French <sfrench@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
NETDEV_NOTIFY_PEER is an explicit request by the driver to send a link
notification while NETDEV_UP/NETDEV_CHANGEADDR generate link
notifications as a sort of side effect.
In the later cases the sysctl option is present because link
notification events can have undesired effects e.g. if the link is
flapping. I don't think this applies in the case of an explicit
request from a driver.
This patch makes NETDEV_NOTIFY_PEER unconditional, if preferred we
could add a new sysctl for this case which defaults to on.
This change causes Xen post-migration ARP notifications (which cause
switches to relearn their MAC tables etc) to be sent by default.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[reported to solve hyperv live migration problem - gkh] Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Mike Surcouf <mike@surcouf.co.uk> Cc: Hank Janssen <hjanssen@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the iowarrior devices in this case statement support more than 8 bytes
per report, it is possible to write past the end of a kernel heap allocation.
This will probably never be possible, but change the allocation to be more
defensive anyway.
For some time is known that ASPM is causing troubles on r8169, i.e. make
device randomly stop working without any errors in dmesg.
Currently Tomi Leppikangas reports that system with r8169 device hangs
with MCE errors when ASPM is enabled:
https://bugzilla.redhat.com/show_bug.cgi?id=642861#c4
Lets disable ASPM for r8169 devices at all, to avoid problems with
r8169 PCIe devices at least for some users.
Reported-by: Tomi Leppikangas <tomi.leppikangas@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When support for 82577/82578 was added[1] in 2.6.31, PHY wakeup was in-
advertently enabled (even though it does not function properly) on ICH10
LOMs. This patch makes it so that the ICH10 LOMs use MAC wakeup instead
as was done with the initial support for those devices (i.e. 82567LM-3,
82567LF-3 and 82567V-4).
This fixes a bug in the order of dccp_rcv_state_process() that still permitted
reception even after closing the socket. A Reset after close thus causes a NULL
pointer dereference by not preventing operations on an already torn-down socket.
dccp_v4_do_rcv()
|
| state other than OPEN
v
dccp_rcv_state_process()
|
| DCCP_PKT_RESET
v
dccp_rcv_reset()
|
v
dccp_time_wait()
WARNING: at net/ipv4/inet_timewait_sock.c:141 __inet_twsk_hashdance+0x48/0x128()
Modules linked in: arc4 ecb carl9170 rt2870sta(C) mac80211 r8712u(C) crc_ccitt ah
[<c0038850>] (unwind_backtrace+0x0/0xec) from [<c0055364>] (warn_slowpath_common)
[<c0055364>] (warn_slowpath_common+0x4c/0x64) from [<c0055398>] (warn_slowpath_n)
[<c0055398>] (warn_slowpath_null+0x1c/0x24) from [<c02b72d0>] (__inet_twsk_hashd)
[<c02b72d0>] (__inet_twsk_hashdance+0x48/0x128) from [<c031caa0>] (dccp_time_wai)
[<c031caa0>] (dccp_time_wait+0x40/0xc8) from [<c031c15c>] (dccp_rcv_state_proces)
[<c031c15c>] (dccp_rcv_state_process+0x120/0x538) from [<c032609c>] (dccp_v4_do_)
[<c032609c>] (dccp_v4_do_rcv+0x11c/0x14c) from [<c0286594>] (release_sock+0xac/0)
[<c0286594>] (release_sock+0xac/0x110) from [<c031fd34>] (dccp_close+0x28c/0x380)
[<c031fd34>] (dccp_close+0x28c/0x380) from [<c02d9a78>] (inet_release+0x64/0x70)
The fix is by testing the socket state first. Receiving a packet in Closed state
now also produces the required "No connection" Reset reply of RFC 4340, 8.3.1.
Reported-and-tested-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported-by: Mark Davis Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acan FG-8100 barcode reader (0x04b4/0xbca1) has vendor ID of
cypress and requires the same MIN/MAX swap descriptor quirk
as other barcode readers from cypress.
o If tx and rx resources are not available, during set mac request.
Then this request wont be passed to firmware and it will be added to
driver mac list and will never make it to firmware.
So if resources are not available, don't add it to driver mac list.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As all virtio devices perform DMA, we
must enable bus mastering for them to be
spec compliant.
This patch fixes hotplug of virtio devices
with Linux guests and qemu 0.11-0.12.
Tested-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we finish processing ASCONF_ACK chunk, we try to send
the next queued ASCONF. This action runs the sctp state
machine recursively and it's not prepared to do so.
vfs_rename_other() does not lock renamed inode with i_mutex. Thus changing
i_nlink in a non-atomic manner (which happens in ext2_rename()) can corrupt
it as reported and analyzed by Josh.
In fact, there is no good reason to mess with i_nlink of the moved file.
We did it presumably to simulate linking into the new directory and unlinking
from an old one. But the practical effect of this is disputable because fsck
can possibly treat file as being properly linked into both directories without
writing any error which is confusing. So we just stop increment-decrement
games with i_nlink which also fixes the corruption.
CC: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Josh Hunt <johunt@akamai.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When the per cpu timer is marked CLOCK_EVT_FEAT_C3STOP, then we only
can switch into oneshot mode, when the backup broadcast device
supports oneshot mode as well. Otherwise we would try to switch the
broadcast device into an unsupported mode unconditionally. This went
unnoticed so far as the current available broadcast devices support
oneshot mode. Seth unearthed this problem while debugging and working
around an hpet related BIOS wreckage.
Add the necessary check to tick_is_oneshot_available().
A customer of ours, complained that when setting the reset
vector back to 0, it trashed other data and hung their box.
They noticed when only 4 bytes were set to 0 instead of 8,
everything worked correctly.
Mathew pointed out:
|
| We're supposed to be resetting trampoline_phys_low and
| trampoline_phys_high here, which are two 16-bit values.
| Writing 64 bits is definitely going to overwrite space
| that we're not supposed to be touching.
|
So limit the area modified to u32.
Signed-off-by: Don Zickus <dzickus@redhat.com> Acked-by: Matthew Garrett <mjg@redhat.com>
LKML-Reference: <1297139100-424-1-git-send-email-dzickus@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Current refcounttree codes actually didn't writeback the new pages out in
write-back mode, due to a bug of always passing a ZERO number of clusters
to 'ocfs2_cow_sync_writeback', the patch tries to pass a proper one in.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com> Signed-off-by: Joel Becker <jlbec@evilplan.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In x25_link_free(), we destroy 'nb' before dereferencing
'nb->dev'. Don't do this, because 'nb' might be freed
by then.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Tested-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
does not take into account that the remaining data length can be less
than sg_dma_len(sg). In that case, running_total can end up being
greater than the total data length, so an extra TRB is counted.
Changing the expression to
while (running_total < sg_dma_len(sg) && running_total < temp)
fixes that.
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
are incorrect, because running_total can never be zero, so the if()
expression will never be true. I think the intention was that
running_total be in the range of 0 to TRB_MAX_BUFF_SIZE-1, not 1
to TRB_MAX_BUFF_SIZE. So adding a
running_total &= TRB_MAX_BUFF_SIZE - 1;
fixes the problem.
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes it easier to spot some problems, which will be fixed by the
next patch in the series. Also change dev_dbg to dev_err in
check_trb_math(), so any math errors will be visible even when running
with debug disabled.
Note: This patch changes the expressions containing
"((1 << TRB_MAX_BUFF_SHIFT) - 1)" to use the equivalent
"(TRB_MAX_BUFF_SIZE - 1)". No change in behavior is intended for
those expressions.
This patch should be queued for stable kernels back to 2.6.31.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some SB800 systems polarity for IOAPIC pin2 is wrongly
specified as low active by BIOS. This caused system hangs after
resume from S3 when HPET was used in one-shot mode on such
systems because a timer interrupt was missed (HPET signal is
high active).
'mdp' devices are md devices with preallocated device numbers
for partitions. As such it is possible to mknod and open a partition
before opening the whole device.
this causes md_probe() to be called with a device number of a
partition, which in-turn calls mddev_find with such a number.
However mddev_find expects the number of a 'whole device' and
does the wrong thing with partition numbers.
So add code to mddev_find to remove the 'partition' part of
a device number and just work with the 'whole device'.
This patch addresses https://bugzilla.kernel.org/show_bug.cgi?id=28652
The kernel automatically evaluates partition tables of storage devices.
The code for evaluating LDM partitions (in fs/partitions/ldm.c) contains
a bug that causes a kernel oops on certain corrupted LDM partitions. A
kernel subsystem seems to crash, because, after the oops, the kernel no
longer recognizes newly connected storage devices.
The patch changes ldm_parse_vmdb() to Validate the value of vblk_size.
Signed-off-by: Timo Warns <warns@pre-sense.de> Cc: Eugene Teo <eugeneteo@kernel.sg> Acked-by: Richard Russon <ldm@flatcap.org> Cc: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In several places, an epoll fd can call another file's ->f_op->poll()
method with ep->mtx held. This is in general unsafe, because that other
file could itself be an epoll fd that contains the original epoll fd.
The code defends against this possibility in its own ->poll() method using
ep_call_nested, but there are several other unsafe calls to ->poll
elsewhere that can be made to deadlock. For example, the following simple
program causes the call in ep_insert recursively call the original fd's
->poll, leading to deadlock:
#include <unistd.h>
#include <sys/epoll.h>
int main(void) {
int e1, e2, p[2];
struct epoll_event evt = {
.events = EPOLLIN
};
On insertion, check whether the inserted file is itself a struct epoll,
and if so, do a recursive walk to detect whether inserting this file would
create a loop of epoll structures, which could lead to deadlock.
[nelhage@ksplice.com: Use epmutex to serialize concurrent inserts] Signed-off-by: Davide Libenzi <davidel@xmailserver.org> Signed-off-by: Nelson Elhage <nelhage@ksplice.com> Reported-by: Nelson Elhage <nelhage@ksplice.com> Tested-by: Nelson Elhage <nelhage@ksplice.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"DMA transfers need to be synced properly in order for
the cpu and device to see the most uptodate and correct
copy of the DMA buffer."
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My Galaxy Spica needs this quirk when in modem mode, otherwise
it causes endless USB bus resets and is unusable in this mode.
Unfortunately Samsung decided to reuse ID of its old CDMA phone SGH-I500
for the modem part.
That's why in addition to this patch the visor driver must be prevented
from binding to SPH-I500 ID, so ACM driver can do that.
Signed-off-by: Maciej Szmigiero <mhej@o2.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[USB]Add Samsung SGH-I500/Android modem ID switch to visor driver
Samsung decided to reuse USB ID of its old CDMA phone SGH-I500 for the
modem part of some of their Android phones. At least Galaxy Spica
is affected.
This modem needs ACM driver and does not work with visor driver which
binds the conflicting ID for SGH-I500.
Because SGH-I500 is pretty an old hardware its best to add switch to
visor
driver in cause somebody still wants to use that phone with Linux.
Note that this is needed only when using the Android phone as modem,
not in USB storage or ADB mode.
Signed-off-by: Maciej Szmigiero <mhej@o2.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1448) adds a quirks entry for the Keytouch QWERTY Panel
firmware, used in the IEC 60945 keyboard. This device crashes during
enumeration when the computer asks for its configuration string
descriptor.
The idle timer could trigger after clock had been disabled leading to
kernel panic when MUSB_DEVCTL is accessed in musb_do_idle on 2.6.37.
The fault below is no longer triggered on 2.6.38-rc4 (clock is disabled
later, and only if compiled as a module, and the offending memory access
has moved) but the timer should be cancelled nonetheless.
With CONFIG_SHIRQ_DEBUG=y we call a newly installed interrupt handler
in request_threaded_irq().
The original implementation (commit a304e1b8) called the handler
_BEFORE_ it was installed, but that caused problems with handlers
calling disable_irq_nosync(). See commit 377bf1e4.
It's braindead in the first place to call disable_irq_nosync in shared
handlers, but ....
Moving this call after we installed the handler looks innocent, but it
is very subtle broken on SMP.
Interrupt handlers rely on the fact, that the irq core prevents
reentrancy.
Now this debug call violates that promise because we run the handler
w/o the IRQ_INPROGRESS protection - which we cannot apply here because
that would result in a possibly forever masked interrupt line.
A concurrent real hardware interrupt on a different CPU results in
handler reentrancy and can lead to complete wreckage, which was
unfortunately observed in reality and took a fricking long time to
debug.
Leave the code here for now. We want this debug feature, but that's
not easy to fix. We really should get rid of those
disable_irq_nosync() abusers and remove that function completely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't allow everybody to change ACPI settings. The comment says that it
is done deliberatelly, however, the comment before disp_proc_write()
says that at least one of these setting is experimental.
The lower filesystem may do some type of inode revalidation during a
getattr call. eCryptfs should take advantage of that by copying the
lower inode attributes to the eCryptfs inode after a call to
vfs_getattr() on the lower inode.
I originally wrote this fix while working on eCryptfs on nfsv3 support,
but discovered it also fixed an eCryptfs on ext4 nanosecond timestamp
bug that was reported.
Ensure a predictable endian state when entering signal handlers. This
avoids programs which use SETEND to momentarily switch their endian
state from having their signal handlers entered with an unpredictable
endian state.
Acked-by: Dave Martin <dave.martin@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
| drivers/media/radio/radio-aimslab.c: In function ‘rt_decvol’:
| drivers/media/radio/radio-aimslab.c:76: error: implicit declaration of function ‘msleep’
Currently we return 0 in swsusp_alloc() when alloc_image_page() fails.
Fix that. Also remove unneeded "error" variable since the only
useful value of error is -ENOMEM.
[rjw: Fixed up the changelog and changed subject.]
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
task_show_regs used to be a debugging aid in the early bringup days
of Linux on s390. /proc/<pid>/status is a world readable file, it
is not a good idea to show the registers of a process. The only
correct fix is to remove task_show_regs.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 7124fe0a5b619d65b739477b3b55a20bf805b06d ("xfs: validate untrusted inode
numbers during lookup") changes the inode lookup code to do btree lookups for
untrusted inode numbers. This change made an invalid assumption about the
alignment of inodes and hence incorrectly calculated the first inode in the
cluster. As a result, some inode numbers were being incorrectly considered
invalid when they were actually valid.
The issue was not picked up by the xfstests suite because it always runs fsr
and dump (the two utilities that utilise the bulkstat interface) on cache hot
inodes and hence the lookup code in the cold cache path was not sufficiently
exercised to uncover this intermittent problem.
Fix the issue by relaxing the btree lookup criteria and then checking if the
record returned contains the inode number we are lookup for. If it we get an
incorrect record, then the inode number is invalid.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
[dannf: Backported to 2.6.32.y] Cc: dann frazier <dannf@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The block number comes from bulkstat based inode lookups to shortcut
the mapping calculations. We ar enot able to trust anything from
bulkstat, so drop the block number as well so that the correct
lookups and mappings are always done.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
[dannf: Backported to 2.6.32.y] Cc: dann frazier <dannf@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Inode numbers may come from somewhere external to the filesystem
(e.g. file handles, bulkstat information) and so are inherently
untrusted. Rename the flag we use for these lookups to make it
obvious we are doing a lookup of an untrusted inode number and need
to verify it completely before trying to read it from disk.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
[dannf: backported to 2.6.32.y] Cc: dann frazier <dannf@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When we decode a handle or do a bulkstat lookup, we are using an
inode number we cannot trust to be valid. If we are deleting inode
chunks from disk (default noikeep mode), then we cannot trust the on
disk inode buffer for any given inode number to correctly reflect
whether the inode has been unlinked as the di_mode nor the
generation number may have been updated on disk.
This is due to the fact that when we delete an inode chunk, we do
not write the clusters back to disk when they are removed - instead
we mark them stale to avoid them being written back potentially over
the top of something that has been subsequently allocated at that
location. The result is that we can have locations of disk that look
like they contain valid inodes but in reality do not. Hence we
cannot simply convert the inode number to a block number and read
the location from disk to determine if the inode is valid or not.
As a result, and XFS_IGET_BULKSTAT lookup needs to actually look the
inode up in the inode allocation btree to determine if the inode
number is valid or not.
It should be noted even on ikeep filesystems, there is the
possibility that blocks on disk may look like valid inode clusters.
e.g. if there are filesystem images hosted on the filesystem. Hence
even for ikeep filesystems we really need to validate that the inode
number is valid before issuing the inode buffer read.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
[dannf: backported to 2.6.32.y] Cc: dann frazier <dannf@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The non-coherent bulkstat versionsthat look directly at the inode
buffers causes various problems with performance optimizations that
make increased use of just logging inodes. This patch makes bulkstat
always use iget, which should be fast enough for normal use with the
radix-tree based inode cache introduced a while ago.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Dave Chinner <dchinner@redhat.com>
[dannf: backported to 2.6.32.y] Cc: dann frazier <dannf@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported-by: Min Zhang <mzhang@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Moritz Muehlenhoff <jmm@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As noted by Steve Chen, since commit f5fff5dc8a7a3f395b0525c02ba92c95d42b7390 ("tcp: advertise MSS
requested by user") we can end up with a situation where
tcp_select_initial_window() does a divide by a zero (or
even negative) mss value.
The problem is that sometimes we effectively subtract
TCPOLEN_TSTAMP_ALIGNED and/or TCPOLEN_MD5SIG_ALIGNED from the mss.
Fix this by increasing the minimum from 8 to 64.
Reported-by: Steve Chen <schen@mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Moritz Muehlenhoff <jmm@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For certain skews of the BE adapter, H/W Tx and Rx
counters could be common for more than one interface.
Add Tx and Rx counters in the adapter structure
(to maintain stats on a per interfae basis).
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't forget to release the module refcnt if seq_open() returns failure.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Cc: J. Bruce Fields <bfields@fieldses.org> Cc: Neil Brown <neilb@suse.de> Cc: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When suspending a failed mirror, bios are completed by mirror_end_io() and
__rh_lookup() in dm_rh_dec() returns NULL where a non-NULL return value is
required by design. Fix this by not changing the state of the recovery failed
region from DM_RH_RECOVERING to DM_RH_NOSYNC in dm_rh_recovery_end().
Issue
On 2.6.33-rc1 kernel, I hit the bug when I suspended the failed
mirror by dmsetup command.
When recovery process of a region failed, dm_rh_recovery_end() function
changes the state of the region from RM_RH_RECOVERING to DM_RH_NOSYNC.
When recovery_complete() is executed between dm_rh_update_states() and
dm_writes() in do_mirror(), bios are processed with the region state,
DM_RH_NOSYNC. However, the region data is freed without checking its
pending count when dm_rh_update_states() is called next time.
When bios are finished by mirror_end_io(), __rh_lookup() in dm_rh_dec()
returns NULL even though a valid return value are expected.
Solution
Remove the state change of the recovery failed region from DM_RH_RECOVERING
to DM_RH_NOSYNC in dm_rh_recovery_end(). We can remove the state change
because:
- If the region data has been released by dm_rh_update_states(),
a new region data is created with the state of DM_RH_NOSYNC, and
bios are processed according to the DM_RH_NOSYNC state.
- If the region data has not been released by dm_rh_update_states(),
a state of the region is DM_RH_RECOVERING and bios are put in the
delayed_bio list.
The flag change from DM_RH_RECOVERING to DM_RH_NOSYNC in dm_rh_recovery_end()
was added in the following commit:
dm raid1: handle resync failures
author Jonathan Brassow <jbrassow@redhat.com>
Thu, 12 Jul 2007 16:29:04 +0000 (17:29 +0100)
http://git.kernel.org/linus/f44db678edcc6f4c2779ac43f63f0b9dfa28b724
This patch solves a corner case during allocation which occurs if both
metadata (indirect) and data blocks are required but there is an
obstacle in the filesystem (e.g. a resource group header or another
allocated block) such that when the allocation is requested only
enough blocks for the metadata are returned.
By changing the exit condition of this loop, we ensure that a
minimum of one data block will always be returned.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the mirror log fails when the handle_errors option was not selected
and there is no remaining valid mirror leg, writes return success even
though they weren't actually written to any device. This patch
completes them with EIO instead.
This code path is taken:
do_writes:
bio_list_merge(&ms->failures, &sync);
do_failures:
if (!get_valid_mirror(ms)) (false)
else if (errors_handled(ms)) (false)
else bio_endio(bio, 0);
The logic in do_failures is based on presuming that the write was already
tried: if it succeeded at least on one leg (without handle_errors) it
is reported as success.
Adds IBM Power Virtual SCSI ALUA devices to the ALUA device handler.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PowerPC architecture does not require loads to independent bytes to be
ordered without adding an explicit barrier.
In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.
The problem occurs with packet split enabled where the TCP/IP header and data
are in different descriptors. If the reads go out of order we may have data
that doesn't match the TCP/IP header. Since we use hardware checksumming this
bad data is never verified and it makes it all the way to the application.
This bug was found during stress testing and adding this barrier has been shown
to fix it.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch will add the device ID for the 82599-based Ethernet
Express Module X520-P2 SFI card.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: maximilian attems <max@stro.at> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
By the commit af7fa16 2010-08-03 NFS: Fix up the fsync code
close(2) became returning the non-zero value even if it went well.
nfs_file_fsync() should return 0 when "status" is positive.
Signed-off-by: J. R. Okajima <hooanon05@yahoo.co.jp> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sendfile(2) was reworked with the splice infrastructure, but it still
checks f_op.sendpage() instead of f_op.splice_write() wrongly. Although
if f_op.sendpage() exists, f_op.splice_write() always exists at the same
time currently, the assumption will be broken in future silently. This
patch also brings a side effect: sendfile(2) can work with any output
file. Some security checks related to f_op are added too.
In prepare_kernel_cred() since 2.6.29, put_cred(new) is called without
assigning new->usage when security_prepare_creds() returned an error. As a
result, memory for new and refcount for new->{user,group_info,tgcred} are
leaked because put_cred(new) won't call __put_cred() unless old->usage == 1.
Fix these leaks by assigning new->usage (and new->subscribers which was added
in 2.6.32) before calling security_prepare_creds().
In cred_alloc_blank() since 2.6.32, abort_creds(new) is called with
new->security == NULL and new->magic == 0 when security_cred_alloc_blank()
returns an error. As a result, BUG() will be triggered if SELinux is enabled
or CONFIG_DEBUG_CREDENTIALS=y.
If CONFIG_DEBUG_CREDENTIALS=y, BUG() is called from __invalid_creds() because
cred->magic == 0. Failing that, BUG() is called from selinux_cred_free()
because selinux_cred_free() is not expecting cred->security == NULL. This does
not affect smack_cred_free(), tomoyo_cred_free() or apparmor_cred_free().
Fix these bugs by
(1) Set new->magic before calling security_cred_alloc_blank().
(2) Handle null cred->security in creds_are_invalid() and selinux_cred_free().
In get_empty_filp() since 2.6.29, file_free(f) is called with f->f_cred == NULL
when security_file_alloc() returned an error. As a result, kernel will panic()
due to put_cred(NULL) call within RCU callback.
Fix this bug by assigning f->f_cred before calling security_file_alloc().
Ben Hutchings [Mon, 7 Feb 2011 19:20:55 +0000 (19:20 +0000)]
bonding/vlan: Avoid mangled NAs on slaves without VLAN tag insertion
This is related to commit f88a4a9b65a6f3422b81be995535d0e69df11bb8
upstream, but the bug cannot be properly fixed without the other
changes to VLAN tagging in 2.6.37.
bond_na_send() attempts to insert a VLAN tag in between building and
sending packets of the respective formats. If the slave does not
implement hardware VLAN tag insertion then vlan_put_tag() will mangle
the network-layer header because the Ethernet header is not present at
this point (unlike in bond_arp_send()).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's possible for get_task_cred() as it currently stands to 'corrupt' a set of
credentials by incrementing their usage count after their replacement by the
task being accessed.
What happens is that get_task_cred() can race with commit_creds():
However, since a tasks credentials are generally not changed very often, we can
reasonably make use of a loop involving reading the creds pointer and using
atomic_inc_not_zero() to attempt to increment it if it hasn't already hit zero.
If successful, we can safely return the credentials in the knowledge that, even
if the task we're accessing has released them, they haven't gone to the RCU
cleanup code.
We then change task_state() in procfs to use get_task_cred() rather than
calling get_cred() on the result of __task_cred(), as that suffers from the
same problem.
Without this change, a BUG_ON in __put_cred() or in put_cred_rcu() can be
tripped when it is noticed that the usage count is not zero as it ought to be,
for example:
If the guest domain has been suspend/resumed or migrated, then the
system clock backing the pvclock clocksource may revert to a smaller
value (ie, can be non-monotonic across the migration/save-restore).
Make sure we zero last_value in that case so that the domain
continues to see clock updates.
This patch (as1417) fixes a problem affecting some (or all) nVidia
chipsets. When the computer is shut down, the OHCI controllers
continue to power the USB buses and evidently they drive a Reset
signal out all their ports. This prevents attached devices from going
to low power. Mouse LEDs stay on, for example, which is disconcerting
for users and a drain on laptop batteries.
The fix involves leaving each OHCI controller in the OPERATIONAL state
during system shutdown rather than putting it in the RESET state.
Although this nominally means the controller is running, in fact it's
not doing very much since all the schedules are all disabled. However
there is ongoing DMA to the Host Controller Communications Area, so
the patch also disables the bus-master capability of all PCI USB
controllers after the shutdown routine runs.
The fix is applied only to nVidia-based PCI OHCI controllers, so it
shouldn't cause problems on systems using other hardware. As an added
safety measure, in case the kernel encounters one of these running
controllers during boot, the patch changes quirk_usb_handoff_ohci()
(which runs early on during PCI discovery) to reset the controller
before anything bad can happen.
Reported-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: David Brownell <david-b@pacbell.net> Tested-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If CPU support always running local APIC timer, per-cpu hpet
timer could be disabled, which is useless and wasteful in such
case. Let's leave the timers to others.
The effect is that we reserve less timers.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Cc: venkatesh.pallipadi@intel.com
LKML-Reference: <20090812031612.GA10062@sli10-desk.sh.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Thomas Renninger <trenn@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
x25 does not decrement the network device reference counts on module unload.
Thus unregistering any pre-existing interface after unloading the x25 module
hangs and results in
unregister_netdevice: waiting for tap0 to become free. Usage count = 1
This patch decrements the reference counts of all interfaces in x25_link_free,
the way it is already done in x25_link_device_down for NETDEV_DOWN events.
Signed-off-by: Apollon Oikonomopoulos <apollon@noc.grnet.gr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a possibility malicious users can get limited information about
uninitialized stack mem array. Even if sk_run_filter() result is bound
to packet length (0 .. 65535), we could imagine this can be used by
hostile user.
Initializing mem[] array, like Dan Rosenberg suggested in his patch is
expensive since most filters dont even use this array.
Its hard to make the filter validation in sk_chk_filter(), because of
the jumps. This might be done later.
In this patch, I use a bitmap (a single long var) so that only filters
using mem[] loads/stores pay the price of added security checks.
For other filters, additional cost is a single instruction.
[ Since we access fentry->k a lot now, cache it in a local variable
and mark filter entry pointer as const. -DaveM ]
Reported-by: Dan Rosenberg <drosenberg@vsecurity.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[Backported by dann frazier <dannf@debian.org>] Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PKT_CTRL_CMD_STATUS device ioctl retrieves a pointer to a
pktcdvd_device from the global pkt_devs array. The index into this
array is provided directly by the user and is a signed integer, so the
comparison to ensure that it falls within the bounds of this array will
fail when provided with a negative index.
This can be used to read arbitrary kernel memory or cause a crash due to
an invalid pointer dereference. This can be exploited by users with
permission to open /dev/pktcdvd/control (on many distributions, this is
readable by group "cdrom").
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
[ Rather than add a cast, just make the function take the right type -Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If ocfs2_live_connection_list is empty, ocfs2_connection_find() will return
a pointer to the LIST_HEAD, cast as a ocfs2_live_connection. This can cause
an oops when ocfs2_control_send_down() dereferences c->oc_conn:
The sctp_asoc_get_hmac() function iterates through a peer's hmac_ids
array and attempts to ensure that only a supported hmac entry is
returned. The current code fails to do this properly - if the last id
in the array is out of range (greater than SCTP_AUTH_HMAC_ID_MAX), the
id integer remains set after exiting the loop, and the address of an
out-of-bounds entry will be returned and subsequently used in the parent
function, causing potentially ugly memory corruption. This patch resets
the id integer to 0 on encountering an invalid id so that NULL will be
returned after finishing the loop if no valid ids are found.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a branch at the end of this function that
is supposed to normalize the return value with what
the mid-layer expects. In this one case, we get it wrong.
Also increase the verbosity of the INFO level printk
at the end of mptscsih_abort to include the actual return value
and the scmd->serial_number. The reason being success
or failure is actually determined by the state of
the internal tag list when a TMF is issued, and not the
return value of the TMF cmd. The serial_number is also
used in this decision, thus it's useful to know for debugging
purposes.
Reported-by: Peter M. Petrakis <peter.petrakis@canonical.com> Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added missing release callback for file_operations mptctl_fops.
Without release callback there will be never freed. It remains on
mptctl's eent list even after the file is closed and released.
If nfsd fails to find an exported via NFS file in the readahead cache, it
should increment corresponding nfsdstats counter (ra_depth[10]), but due to a
bug it may instead write to ra_depth[11], corrupting the following field.
In a kernel with NFSDv4 compiled in the corruption takes the form of an
increment of a counter of the number of NFSv4 operation 0's received; since
there is no operation 0, this is harmless.
In a kernel with NFSDv4 disabled it corrupts whatever happens to be in the
memory beyond nfsdstats.
Signed-off-by: Konstantin Khorenko <khorenko@openvz.org> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log