pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
Currrently the gpio_chip.to_irq() callback returns -ENOSYS on error,
which causes bad interactions with the serial_mctrl_gpio helpers.
mctrl_gpio_init() returns -ENOSYS if GPIOLIB is not enabled, which is
intended to be ignored by its callers. However, ignoring -ENOSYS when it
was caused by a gpiod_to_irq() failure will lead to a crash later:
Unable to handle kernel paging request at virtual address ffffffde
...
PC is at mctrl_gpio_set+0x14/0x78
Fix this by returning zero instead, like gpiochip_to_irq() does.
Make it possible to name the producer side of a GPIO line using
a "gpio-line-names" property array, modeled on the
"clock-output-names" property from the clock bindings.
This naming is especially useful for:
- Debugging: lines are named after function, not just opaque
offset numbers.
- Exploration: systems where some or all GPIO lines are available
to end users, such as prototyping, one-off's "makerspace usecases"
users are helped by the names of the GPIO lines when tinkering.
This usecase has been surfacing recently.
The gpio-line-names attribute is completely optional.
Example output from lsgpio on a patched Snowball tree:
GPIO chip: gpiochip6, "8000e180.gpio", 32 GPIO lines
line 0: unnamed unused
line 1: "AP_GPIO161" "extkb3" [kernel]
line 2: "AP_GPIO162" "extkb4" [kernel]
line 3: "ACCELEROMETER_INT1_RDY" unused [kernel]
line 4: "ACCELEROMETER_INT2" unused
line 5: "MAG_DRDY" unused [kernel]
line 6: "GYRO_DRDY" unused [kernel]
line 7: "RSTn_MLC" unused
line 8: "RSTn_SLC" unused
line 9: "GYRO_INT" unused
line 10: "UART_WAKE" unused
line 11: "GBF_RESET" unused
line 12: unnamed unused
Cc: Grant Likely <grant.likely@linaro.org> Cc: Amit Kucheria <amit.kucheria@linaro.org> Cc: David Mandala <david.mandala@linaro.org> Cc: Lee Campbell <leecam@google.com> Cc: devicetree@vger.kernel.org Acked-by: Rob Herring <robh@kernel.org> Reviewed-by: Michael Welling <mwelling@ieee.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement gpio_get_direction() callback for Tegra GPIO.
The direction is only valid if the pin is configured as
GPIO. If pin is not configured in GPIO mode then this
function return error.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the gpiochip supports the .get_direction() callback, then
the initial state of the descriptor flags should be set up
as output accordingly. Also put in comments explaining what is
going on.
This patch renames the gpio-generic.c into gpio-mmio.c.
This is because currently the file only contains code
for a memory-mapped GPIO driver. There isn't any support
for ioports or other resource type.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
GPIO_GENERIC_PLATFORM is a tristate. If the module option is
selected the resulting gpio-generic.ko will lack most of the
module initialzation and probe code.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio-mpc8xxx driver requires IRQ domains but can be built
without them, resulting on a failure to build certain randconfigs
on ARM:
drivers/gpio/gpio-mpc8xxx.c: In function 'mpc8xxx_gpio_to_irq':
drivers/gpio/gpio-mpc8xxx.c:92:10: error: implicit declaration of function 'irq_create_mapping' [-Werror=implicit-function-declaration]
return irq_create_mapping(mpc8xxx_gc->irq, offset);
This selects IRQ_DOMAIN from the driver to ensure we can build it.
gpio: tegra: Get rid of all file scoped global variables
Move the file scoped multiple global variable from Tegra GPIO
driver to the structure and make this as gpiochip data which
can be referred from GPIO chip callbacks.
gpio: omap: fix irq triggering in smart-idle wakeup mode
Now GPIO IRQ loss is observed on dra7-evm after suspend/resume cycle
in the following case:
extcon_usb1(id_irq) -> pcf8575.gpio1 -> omapgpio6.gpio11 -> gic
the extcon_usb1 is wake up source and it enables IRQ wake up for
id_irq by calling enable/disable_irq_wake() during suspend/resume
which, in turn, causes execution of omap_gpio_wake_enable(). And
omap_gpio_wake_enable() will set/clear corresponding bit in
GPIO_IRQWAKEN_x register.
omapgpio6 configuration after boot - wakeup is enabled for GPIO IRQs
by default from omap_gpio_irq_type:
GPIO_IRQSTATUS_SET_0 | 0x00000400
GPIO_IRQSTATUS_CLR_0 | 0x00000400
GPIO_IRQWAKEN_0 | 0x00000400
GPIO_RISINGDETECT | 0x00000000
GPIO_FALLINGDETECT | 0x00000400
As result, system will start to lose interrupts from pcf8575 GPIO
expander, because when OMAP GPIO IP is in smart-idle wakeup mode, there
is no guarantee that transition(s) on input non wake up GPIO pin will
trigger asynchronous wake-up request to PRCM and then IRQ generation.
IRQ will be generated when GPIO is in active mode - for example, some
time after accessing GPIO bank registers IRQs will be generated
normally, but issue will happen again once PRCM will put GPIO in low
power smart-idle wakeup mode.
Note 1. Issue is not reproduced if debounce clk is enabled for GPIO
bank.
Note 2. Issue hardly reproducible if GPIO pins group contains both
wakeup/non-wakeup gpios - for example, it will be hard to reproduce
issue with pin2 if GPIO_IRQWAKEN_0=0x1 GPIO_IRQSTATUS_SET_0=0x3
GPIO_FALLINGDETECT = 0x3 (TRM "Power Saving by Grouping the Edge/Level
Detection").
Note 3. There nothing common bitween System wake up and OMAP GPIO bank
IP wake up logic - the last one defines how the GPIO bank ON-IDLE-ON
transition will happen inside SoC under control of PRCM.
Hence, fix the problem by removing omap_set_gpio_wakeup() function
completely and so keeping always in sync GPIO IRQ mask/unmask
(IRQSTATUS_SET) and wake up enable (GPIO_IRQWAKEN) bits; and adding
IRQCHIP_MASK_ON_SUSPEND flag in OMAP GPIO irqchip. That way non wakeup
GPIO IRQs will be properly masked/unmask by IRQ PM core during
suspend/resume cycle.
Cc: Roger Quadros <rogerq@ti.com> Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This symbols is not needed to get access to selecting the
GPIOLIB anymore: any arch can select GPIOLIB.
Cc: Michael Büsch <m@bues.ch> Cc: sparclinux@vger.kernel.org Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: remove deps on ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
The GPIOLIB symbol currently require that
ARCH_WANT_OPTIONAL_GPIOLIB or ARCH_REQUIRE_GPIOLIB is selected
to be selectable.
The ARCH_REQUIRE_GPIOLIB does only one thing: select GPIOLIB.
This is just confusing: architectures that want GPIOLIB should
be able to configure it in no matter what, and those who
require it should just select GPIOLIB.
It also creates problems for drivers that need to state
"select GPIOLIB" to get dependencies: those depend on the
selected architecture to select
ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB first, and will cause
compile errors for the few archs that state neither.
These intermediary symbols need to go.
As a first step, remove the dependencies so that:
- ARCH_WANT_OPTIONAL_GPIOLIB becomes a noop (GPIOLIB will be
available for everyone) and
- "select ARCH_REQUIRE_GPIOLIB" can be replaced by just
"select GPIOLIB"
After this patch we can follow up with patches cleaning up the
architectures one-by one and eventually remove the
ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB symbols altogether.
Reported-by: Michael Hennerich <michael.hennerich@analog.com> Cc: Michael Büsch <m@bues.ch> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This renames gpiod_set_array_value_priv() to
gpiod_set_array_value_complex() and moves it to the gpiolib.h
private header file so we can reuse it in the subsystem.
Fixes: f90c6bdb690b ("gpio: f7188x: use the new open drain callback") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WM8994 GPIOs clearly have a dedicated open drain control
register. Implement support for controlling this from GPIO
descriptor tables or other hardware descriptions such as
device tree by implementing the .set_single_ended() callback.
Before this patch, lines requesting open drain will just be
switched to input mode by the framework, thus emulating open
drain. But the hardware can do the real thing, so let's
support that.
As part of this, rename the debugfs string for output mode
from "CMOS" to "push-pull" because it is the term used in
the framework to signify a tomem-pole CMOS output.
Cc: patches@opensource.wolfsonmicro.com Cc: Mark Brown <broonie@kernel.org> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WM831x GPIOs clearly have a dedicated open drain control
register. Implement support for controlling this from GPIO
descriptor tables or other hardware descriptions such as
device tree by implementing the .set_single_ended() callback.
Before this patch, lines requesting open drain will just be
switched to input mode by the framework, thus emulating open
drain. But the hardware can do the real thing, so let's
support that.
As part of this, rename the debugfs string for output mode
from "CMOS" to "push-pull" because it is the term used in
the framework to signify a tomem-pole CMOS output.
Cc: patches@opensource.wolfsonmicro.com Cc: Mark Brown <broonie@kernel.org> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The vx855 driver clearly states it has three groups of lines:
GPI, GPO and GPIO. The GPO are assumedly push-pull. The GPIO
are implicit open drain, but if the GPIO subsystem ask for them
to be explicitly open drain (i.e. set the flag on a machine table
that we want open drain) it will currently misbehave: it will
switch the GPIOs to input mode (emulate open drain). Instead:
indicate in the .set_single_ended() callback that we support
open drain and open drain only.
Cc: Daniel Drake <drake@endlessm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The menz127 driver tries to support open drain by detecting it
at request time. However: without the new callbacks from the
gpiolib it is not really working: the core will still just emulate
the open drain mode by switching the line to an input.
By adding a hook into the new .set_single_ended() call rather than
trying to autodetect at request() time, proper open drain can be
supported.
Cc: Andreas Werner <andy@wernerandy.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One variant of the SX150X GPIO chip supports setting the pins in
open drain mode. This is currently available to set from platform
data, but completely unused in the kernel.
Activate the new .set_single_ended() callback so users can set
this up from e.g. device tree or board files using the new
GPIO descriptors.
As part of this, delete the platform data open drain setting
method.
The sx150x has some platform data definition in <linux/i2c/sx150x.h>
but this file is only included from the driver in the whole kernel
so move its contents into the driver.
Cc: Wei Chen <Wei.Chen@csr.com> Cc: Peter Rosin <peda@axentia.se> Acked-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TPS65218 supports open drain mode on its three pins,
with one of them configurable also as push-pull. Use the
new .set_single_ended() callback to set this up properly
from the core, so the core actually see it can drive the
pin(s) as open drain, and does not attempt to emulate
open drain by switching the pin to an input.
Acked-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Laxman Dewangan [Fri, 11 Mar 2016 13:43:22 +0000 (19:13 +0530)]
gpio: of: Return error if gpio hog configuration failed
If GPIO hog configuration failed while adding OF based
gpiochip() then return the error instead of ignoring it.
This helps of properly handling the gpio driver dependency.
When adding the gpio hog nodes for NVIDIA's Tegra210 platforms,
the gpio_hogd() fails with EPROBE_DEFER because pinctrl is not
ready at this time and gpio_request() for Tegra GPIO driver
returns error. The error was not causing the Tegra GPIO driver
to fail as the error was getting ignored.
Yong Li [Thu, 7 Apr 2016 04:56:32 +0000 (12:56 +0800)]
gpio: pca953x: add PCAL9535 interrupt support for Galileo Gen2
Galileo Gen2 board uses the PCAL9535 as the GPIO expansion,
it is different from PCA9535 and includes interrupt mask/status registers,
The current driver does not support the interrupt registers configuration,
it causes some gpio pins cannot trigger interrupt events,
this patch fix this issue.
The original patch was submitted by
Josef Ahmad <josef.ahmad@linux.intel.com>
http://git.yoctoproject.org/cgit/cgit.cgi/meta-intel-quark/tree/recipes-kernel/linux/files/0015-Quark-GPIO-1-2-quark.patch
Signed-off-by: Yong Li <yong.b.li@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This has been a totally undocumented feature for years so add some
generic concepts and documentation about open drain/source, include
some facts on how we now support for hardware.
Cc: Michael Hennerich <michael.hennerich@analog.com> Cc: Nicolas Saenz Julienne <nicolassaenzj@gmail.com> Cc: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: tc3589x: implement open drain/source callback
This makes use of the new .set_single_ended() callback to
set the GPIO line as open drain/open source using hardware.
The TC3589x can do this by either disabling the N-MOS
transistor (open drain) or the P-MOS transistor (open source)
of the output driver stage, in the first case making the signal
drive actively low and high impedance as "high" and in the second
case actively high and high impedance, which is as close to native
open drain support as we come.
Cc: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switch to use BIT(n) instead of (1 << n) which is less
to the point. Most GPIO drivers do this to avoid mistakes.
Also switch from using <linux/gpio.h> to the apropriate
<linux/gpio/driver.h> include.
Linus Walleij [Tue, 22 Mar 2016 09:51:16 +0000 (10:51 +0100)]
gpio: support native single-ended hardware drivers
Some GPIO controllers has a special hardware bit we can flip
to support open drain / source. This means that on these hardwares
we do not need to emulate OD/OS by setting the line to input
instead of actively driving it high/low. Add an optional vtable
callback to the driver set_single_ended() so that driver can
implement this in hardware if they have it.
We may need a pinctrl_gpio_set_config() call at some point to
propagate this down to a backing pin control device on systems
with split GPIO/pin control.
Reported-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Axel Lin [Wed, 23 Mar 2016 11:49:41 +0000 (19:49 +0800)]
gpio: tpic2810: Make sure cached buffer has consistent status with h/w status
i2c_smbus_write_byte_data() can fail. To ensure the
cached buffer has consistent status with h/w status, don't
update the cached gpio->buffer if write fails.
Also refactor the code a bit by adding a tpic2810_set_mask_bits()
helper and use it to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Paul Gortmaker [Sun, 27 Mar 2016 15:44:42 +0000 (11:44 -0400)]
gpio: mb86s7x: make explicitly non-modular
The Kconfig for this driver is currently:
config GPIO_MB86S7X
bool "GPIO support for Fujitsu MB86S7x Platforms"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
gpio: gpio-it87: Add support for IT8620 and IT8628
These chips seem to have a 9th GPIO block (thus supporting 72 GPIOs)
which is configured through SuperIO register 0xd2 (output enable) and
0xd3 (simple I/O). This is also the reason why io_size is larger than
on IT8728 / IT8732. Unfortunately I don't have hardware to test this 9th
GPIO block.
I am also not sure about not configuring the Simple I/O registers as the
hardware I have only uses GPIO block 8. Reading back the values of
0xc0-0xc7 (as configured by the BIOS/EFI on my board) shows that all
have 0xff set.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
tools/gpio: Add missing initialization of device_name
lsgpio.c: In function ‘main’:
lsgpio.c:166:7: warning: ‘device_name’ may be used uninitialized in this functio
n [-Wmaybe-uninitialized]
ret = list_device(device_name);
^
Alexander Stein [Wed, 23 Mar 2016 17:01:27 +0000 (18:01 +0100)]
gpio: mcp23s08: Add support for level triggered interrupts
The interrupt for the corresponding pin is configured to trigger when the
pin state changes compared to a preconfigured state (Bit set in INTCON).
This state is set by setting/clearing the bit in DEFVAL.
In the interrupt handler we need also to check if the bit in INTCON is set
for level triggered interrupts.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Axel Lin [Thu, 17 Mar 2016 04:01:43 +0000 (12:01 +0800)]
gpio: xgene-sb: Use irq_domain_free_irqs_common()
Current code calls irq_domain_alloc_irqs_parent() in .alloc,
so it should call irq_domain_free_irqs_parent() accordingly in .free.
Fix it by switching to use irq_domain_free_irqs_common() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Axel Lin [Thu, 17 Mar 2016 04:00:31 +0000 (12:00 +0800)]
irqdomain: Export irq_domain_free_irqs_common
Export irq_domain_free_irqs_common so it can be used by modules.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 31 Mar 2016 07:09:12 +0000 (09:09 +0200)]
powerpc: ppc4xx: drop unused variable
commit 0d36fe65f58391712e11a6621075f373216e5f00
"powerpc: ppc4xx: use gpiochip data pointer"
made the mm_gc local variable in ppc4xx_gpio_set()
redundant, and when GCC treats warnings as errors this
happens:
arch/powerpc/sysdev/ppc4xx_gpio.c: In function 'ppc4xx_gpio_set':
arch/powerpc/sysdev/ppc4xx_gpio.c:93:26: error:
unused variable 'mm_gc' [-Werror=unused-variable]
struct of_mm_gpio_chip *mm_gc = to_of_mm_gpio_chip(gc);
^
cc1: all warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Anatolij Gustschin <agust@denx.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>