On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Piotr Haber <phaber@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When the next beacon is sent, the ath_buf from the previous run is reused.
If getting a new beacon from mac80211 fails, bf->bf_mpdu is not reset, yet
the skb is freed, leading to a double-free on the next beacon tx attempt,
resulting in a system crash.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On AR9300 the rx FIFO needs to be empty during reset to ensure that no
further DMA activity is generated, otherwise it might lead to memory
corruption issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
SKBs that are allocated in the HTC layer do not have callbacks
registered and hence ended up not being freed, Fix this by freeing
them properly in the TX completion routine.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The length parameter should be sizeof(req->name) - 1 because there is no
guarantee that string provided by userspace will contain the trailing
'\0'.
Can be easily reproduced by manually setting req->name to 128 non-zero
bytes prior to ioctl(HIDPCONNADD) and checking the device name setup on
input subsystem:
When it goes to error through line 144, the memory allocated to *devname is
not freed, and the caller doesn't free it either in line 250. So we free the
memroy of *devname in function cifs_compose_mount_options() when it goes to
error.
Signed-off-by: Cong Ding <dinggnu@gmail.com> Reviewed-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch (as1644) fixes a race that occurs during startup in
uhci-hcd. If the IRQ line is shared with other devices, it's possible
for the handler routine to be called before the data structures are
fully initialized.
The problem is fixed by adding a check to the IRQ handler routine. If
the initialization hasn't finished yet, the routine will return
immediately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Don Zickus <dzickus@redhat.com> Tested-by: "Huang, Adrian (ISS Linux TW)" <adrian.huang@hp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If some other kernel subsystem has a module notifier, and adds a kprobe
to a ftrace mcount point (now that kprobes work on ftrace points),
when the ftrace notifier runs it will fail and disable ftrace, as well
as kprobes that are attached to ftrace points.
A kprobe was added to the init_once() function in the fat module on load.
But this happened before ftrace could have touched the code. As ftrace
didn't run yet, the kprobe system had no idea it was a ftrace point and
simply added a breakpoint to the code (0xcc in the cc:bb:d2:4b:e1).
Then when ftrace went to modify the location from a call to mcount/fentry
into a nop, it didn't see a call op, but instead it saw the breakpoint op
and not knowing what to do with it, ftrace shut itself down.
The solution is to simply give the ftrace module notifier the max priority.
This should have been done regardless, as the core code ftrace modification
also happens very early on in boot up. This makes the module modification
closer to core modification.
Link: http://lkml.kernel.org/r/20130107140333.593683061@goodmis.org Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com> Reported-by: Frank Ch. Eigler <fche@redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Subhash Jadavani reported this partial backtrace:
Now consider this call stack from MMC block driver (this is on the ARMv7
based board):
[<c001b50c>] (v7_dma_inv_range+0x30/0x48) from [<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c)
[<c0017b8c>] (dma_cache_maint_page+0x1c4/0x24c) from [<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c)
[<c0017c28>] (___dma_page_cpu_to_dev+0x14/0x1c) from [<c0017ff8>] (dma_map_sg+0x3c/0x114)
This is caused by incrementing the struct page pointer, and running off
the end of the sparsemem page array. Fix this by incrementing by pfn
instead, and convert the pfn to a struct page.
Suggested-by: James Bottomley <JBottomley@Parallels.com> Tested-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
acpi_processor_get_power_info() has to be called before
acpi_processor_setup_cpuidle_states() to have the latest
information available. This fixes the missing C-state information
after AC-->DC transition.
Signed-off-by: Thomas Schlichter <thomas.schlichter@web.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
(in acpi_processor_power_init) and never sets the per_cpu idle
device. So when acpi_processor_hotplug on CPU online notification
tries to reference said device it crashes:
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The 'intel_idle_probe' probes the CPU and sets the CPU notifier.
But if later on during the module initialization we fail (say
in cpuidle_register_driver), we stop loading, but we neglect
to unregister the CPU notifier. This means that during CPU
hotplug events the system will fail:
calling intel_idle_init+0x0/0x326 @ 1
intel_idle: MWAIT substates: 0x1120
intel_idle: v0.4 model 0x2A
intel_idle: lapic_timer_reliable_states 0xffffffff
intel_idle: intel_idle yielding to none
initcall intel_idle_init+0x0/0x326 returned -19 after 14 usecs
... some time later, offlining and onlining a CPU:
This patch fixes that by moving the CPU notifier registration
as the last item to be done by the module.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bwh: Backported to 3.2: notifier is registered only if we do not have ARAT] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Guests can trigger MMIO exits using dcbf. Since we don't emulate cache
incoherent MMIO, just do nothing and move on.
Reported-by: Ben Collins <ben.c@servergy.com> Signed-off-by: Alexander Graf <agraf@suse.de> Tested-by: Ben Collins <ben.c@servergy.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Add support for the UART device present in Broadcom TruManage capable
NetXtreme chips (ie: 5761m 5762, and 5725).
This implementation has a hidden transmit FIFO, so running in single-byte
interrupt mode results in too many interrupts. The UART_CAP_HFIFO
capability was added to track this. It continues to reload the THR as long
as the THRE and TSRE bits are set in the LSR up to a specified limit (1024
is used here).
Signed-off-by: Stephen Hurd <shurd@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
- Adjust filenames
- Adjust context
- First available port type number is 22 not 24
- s/uart_8250_port/uart_port/
- Use serial_in() not serial_port_in()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
vt6656 has several headers that use the #pragma pack(1) directive to
enable structure packing, but never disable it. The layout of
structures defined in other headers can then depend on which order the
various headers are included in, breaking the One Definition Rule.
In practice this resulted in crashes on x86_64 until the order of header
inclusion was changed for some files in commit 11d404cb56ecd ('staging:
vt6656: fix headers and add cfg80211.'). But we need a proper fix that
won't be affected by future changes to the order of inclusion.
This removes the #pragma pack(1) directives and adds __packed to the
structure definitions for which packing appears to have been intended.
Reported-and-tested-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2]
There has been an error on the xen_failsafe_callback path for failed
iret, which causes the stack pointer to be wrong when entering the
iret_exc error path. This can result in the kernel crashing.
In the classic kernel case, the relevant code looked a little like:
popl %eax # Error code from hypervisor
jz 5f
addl $16,%esp
jmp iret_exc # Hypervisor said iret fault
5: addl $16,%esp
# Hypervisor said segment selector fault
Here, there are two identical addls on either option of a branch which
appears to have been optimised by hoisting it above the jz, and
converting it to an lea, which leaves the flags register unaffected.
In the PVOPS case, the code looks like:
popl_cfi %eax # Error from the hypervisor
lea 16(%esp),%esp # Add $16 before choosing fault path
CFI_ADJUST_CFA_OFFSET -16
jz 5f
addl $16,%esp # Incorrectly adjust %esp again
jmp iret_exc
It is possible unprivileged userspace applications to cause this
behaviour, for example by loading an LDT code selector, then changing
the code selector to be not-present. At this point, there is a race
condition where it is possible for the hypervisor to return back to
userspace from an interrupt, fault on its own iret, and inject a
failsafe_callback into the kernel.
This bug has been present since the introduction of Xen PVOPS support
in commit 5ead97c84 (xen: Core Xen implementation), in 2.6.23.
Signed-off-by: Frediano Ziglio <frediano.ziglio@citrix.com> Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We currently use a temporary 1MB section aligned to a 1MB boundary for
mapping the provided device tree until the final page table is created.
However, if the device tree happens to cross that 1MB boundary, the end
of it remains unmapped and the kernel crashes when it attempts to access
it. Given no restriction on the location of that DTB, it could end up
with only a few bytes mapped at the end of a section.
Solve this issue by mapping two consecutive sections.
Signed-off-by: Nicolas Pitre <nico@linaro.org> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Tested-by: Tomasz Figa <t.figa@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[bwh: Backported to 3.2:
- Adjust context
- The mapping is not conditional; drop the 'ne' suffixes] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Patrik Kluba reports that the preempt count becomes invalid due
to the preempt_enable() call being unbalanced with a
preempt_disable() call in the vfp assembly routines. This happens
because preempt_enable() and preempt_disable() update preempt
counts under PREEMPT_COUNT=y but the vfp assembly routines do so
under PREEMPT=y. In a configuration where PREEMPT=n and
DEBUG_ATOMIC_SLEEP=y, PREEMPT_COUNT=y and so the preempt_enable()
call in VFP_bounce() keeps subtracting from the preempt count
until it goes negative.
Fix this by always using PREEMPT_COUNT to decided when to update
preempt counts in the ARM assembly code.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Reported-by: Patrik Kluba <pkluba@dension.com> Tested-by: Patrik Kluba <pkluba@dension.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Converting a 64 Bit TOD format value to nanoseconds means that the value
must be divided by 4.096. In order to achieve that we multiply with 125
and divide by 512.
When used within sched_clock() this triggers an overflow after appr.
417 days. Resulting in a sched_clock() return value that is much smaller
than previously and therefore may cause all sort of weird things in
subsystems that rely on a monotonic sched_clock() behaviour.
To fix this implement a tod_to_ns() helper function which converts TOD
values without overflow and call this function from both places that
open coded the conversion: sched_clock() and kvm_s390_handle_wait().
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In the slow path, we are forced to copy the relocations prior to
acquiring the struct mutex in order to handle pagefaults. We forgo
copying the new offsets back into the relocation entries in order to
prevent a recursive locking bug should we trigger a pagefault whilst
holding the mutex for the reservations of the execbuffer. Therefore, we
need to reset the presumed_offsets just in case the objects are rebound
back into their old locations after relocating for this exexbuffer - if
that were to happen we would assume the relocations were valid and leave
the actual pointers to the kernels dangling, instant hang.
drm/i915: Handle pagefaults in execbuffer user relocations
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55984 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@fwll.ch> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When shut down SPI port, it's possible that MRDY has been asserted and a SPI
timer was activated waiting for SRDY assert, in the case, it needs to delete
this timer.
Signed-off-by: Chen Jun <jun.d.chen@intel.com> Signed-off-by: channing <chao.bi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Right now using pcie_aspm=force will not enable ASPM if the FADT indicates
ASPM is unsupported. However, the semantics of force should probably allow
for this, especially as they did before 3c076351c4 ("PCI: Rework ASPM
disable code")
This patch just skips the clearing of any ASPM setup that the firmware has
carried out on this bus if pcie_aspm=force is being used.
Reference: http://bugs.launchpad.net/bugs/962038 Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When we have an SHPC-capable bridge with a second SHPC-capable bridge
below it, pushing the upstream bridge's attention button causes a
deadlock.
The deadlock happens because we use the shpchp_wq workqueue to run
shpchp_pushbutton_thread(), which uses shpchp_disable_slot() to remove
devices below the upstream bridge. When we remove the downstream bridge,
we call shpc_remove(), the shpchp driver's .remove() method. That calls
flush_workqueue(shpchp_wq), which deadlocks because the
shpchp_pushbutton_thread() work item is still running.
This patch avoids the deadlock by creating a workqueue for every slot
and removing the single shared workqueue.
Use non-ordered workqueue for attention button events.
Attention button events on each slot can be handled asynchronously. So
we should use non-ordered workqueue. This patch also removes ordered
workqueue in shpchp as a result.
486b10b9f4 ("PCI: pciehp: Handle push button event asynchronously") made
the same change to pciehp. I split this out from a patch by Yijing Wang
<wangyijing@huawei.com> so we fix one thing at a time and to make the
shpchp history correspond more closely with the pciehp history.
The function aer_recover_queue() calls pci_get_domain_bus_and_slot(), which
requires that the caller decrement the reference count with pci_dev_put().
This patch adds the missing call to pci_dev_put().
Signed-off-by: Betty Dall <betty.dall@hp.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Shuah Khan <shuah.khan@hp.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Simple fix to add support for Crucible Technologies COMET Caller ID
USB decoder - a device containing FTDI USB/Serial converter chip,
handling 1200bps CallerID messages decoded from the phone line -
adding correct USB PID is sufficient.
Tested to apply cleanly and work flawlessly against 3.6.9, 3.7.0-rc8
and 3.8.0-rc3 on both amd64 and x86 arches.
Signed-off-by: Tomasz Mloduchowski <q@qdot.me> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When we have a hotplug-capable PCIe port with a second hotplug-capable
PCIe port below it, removing the device below the upstream port causes
a deadlock.
The deadlock happens because we use the pciehp_wq workqueue to run
pciehp_power_thread(), which uses pciehp_disable_slot() to remove devices
below the upstream port. When we remove the downstream PCIe port, we call
pciehp_remove(), the pciehp driver's .remove() method. That calls
flush_workqueue(pciehp_wq), which deadlocks because the
pciehp_power_thread() work item is still running.
This patch avoids the deadlock by creating a workqueue for every PCIe port
and removing the single shared workqueue.
Use non-ordered workqueue for attention button events.
Attention button events on each slot can be handled asynchronously. So
we should use non-ordered workqueue. This patch also removes ordered
workqueue in pciehp as a result.
In the current pciehp, pcied_cleanup() calls destroy_workqueue()
before calling pcie_port_service_unregister(). This causes kernel oops
because flush_workqueue() is called in the pcie_port_service_unregister()
code path after the workqueue was destroyed. So pcied_cleanup() must call
pcie_port_service_unregister() first before calling destroy_workqueue().
The current calculation in pfn_to_bitidx assumes that (pfn -
zone->zone_start_pfn) >> pageblock_order will return the same bit for
all pfn in a pageblock. If zone_start_pfn is not aligned to
pageblock_nr_pages, this may not always be correct.
Consider the following with pageblock order = 10, zone start 2MB:
This means that calling {get,set}_pageblock_migratetype on a single page
will not set the migratetype for the full block. Fix this by rounding
down zone_start_pfn when doing the bitidx calculation.
For our use case, the effects of this bug were mostly tied to the fact
that CMA allocations would either take a long time or fail to happen.
Depending on the driver using CMA, this could result in anything from
visual glitches to application failures.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some touchscreens have buggy firmware which claims
remote wakeup to be enabled after a reset. They nevertheless
crash if the feature is cleared by the host.
Add a check for reset resume before checking for
an enabled remote wakeup feature. On compliant
devices the feature must be cleared after a reset anyway.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Ensure that the aux table is properly initialized, even when optional features
are missing. Without this, the FDPIC loader did not work. This was meant to
be included in commit d5ab780305bb6d60a7b5a74f18cf84eb6ad153b1.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com> Signed-off-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Clear the target role when no target is provided for
the node performing a PRLI.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked by Robert Love <robert.w.love@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When generating a PRLI response to an initiator, clear the
FCP_SPPF_RETRY bit in the response.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked by Robert Love <robert.w.love@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Those rn50 chip are often connected to console remoting hw and load
detection often fails with those. Just don't try to load detect and
report connect.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Use DIV_ROUND_UP to prevent truncation by integer division issue.
This ensures we return enough delay time.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[bwh: Backported to 3.2: delay is done by driver, not returned to the caller] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The ASC/ASCQ code for 'Logical Unit Communication failure' is
0x08/0x00; 0x80/0x00 is vendor specific.
Signed-off-by: Hannes Reinecke <hare@suse.de> Cc: Nicholas Bellinger <nab@risingtidesystems.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[bwh: Backported to 3.2: add offset to buffer index] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If the rpc_task exits while holding the socket write lock before it has
allocated an rpc slot, then the usual mechanism for releasing the write
lock in xprt_release() is defeated.
The problem occurs if the call to xprt_lock_write() initially fails, so
that the rpc_task is put on the xprt->sending wait queue. If the task
exits after being assigned the lock by __xprt_lock_write_func, but
before it has retried the call to xprt_lock_and_alloc_slot(), then
it calls xprt_release() while holding the write lock, but will
immediately exit due to the test for task->tk_rqstp != NULL.
Reported-by: Chris Perl <chris.perl@gmail.com> Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes some code that implements a work-around to a hardware bug in
the ac97 controller on the pxa27x. A bug in the controller's warm reset
functionality requires that the mfp used by the controller as the AC97_nRESET
line be temporarily reconfigured as a generic output gpio (AF0) and manually
held high for the duration of the warm reset cycle. This is what was done in
the original code, but it was broken long ago by commit fb1bf8cd
([ARM] pxa: introduce processor specific pxa27x_assert_ac97reset())
which changed the mfp to a GPIO input instead of a high output.
The fix requires the ac97 controller to obtain the gpio via gpio_request_one(),
with arguments that configure the gpio as an output initially driven high.
Tested on a palm treo 680 machine. Reportedly, this broken code only prevents a
warm reset on hardware that lacks a pull-up on the line, which appears to be the
case for me.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
appears in the kernel log. Through trial-and-error (the pxa270 developer's
manual is mostly incoherent on the topic of ac97 reset), I got cold reset to
complete by setting the WARM_RST bit in the GCR register (and later noticed that
pxa3xx does this for cold reset as well). Also, a timeout loop is needed to
wait for the reset to complete.
Tested on a palm treo 680 machine.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Current code does integer division (min_vol = min_uV / 1000) before pass
min_vol to max8997_get_voltage_proper_val().
So it is possible min_vol is truncated to a smaller value.
For example, if the request min_uV is 800900 for ldo.
min_vol = 800900 / 1000 = 800 (mV)
Then max8997_get_voltage_proper_val returns 800 mV for this case which is lower
than the requested voltage.
Use uV rather than mV in voltage_map_desc to prevent truncation by integer
division.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[bwh: Backported to 3.2:
- Adjust context
- voltage_map_desc also has an n_bits field] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Éric Piel reported a kernel oops in the "comedi_test" module. It was a
NULL pointer dereference within `waveform_ai_interrupt()` (actually a
timer function) that sometimes occurred when a running asynchronous
command is cancelled (either by the `COMEDI_CANCEL` ioctl or by closing
the device file).
This seems to be a race between the caller of `waveform_ai_cancel()`
which on return from that function goes and tears down the running
command, and the timer function which uses the command. In particular,
`async->cmd.chanlist` gets freed (and the pointer set to NULL) by
`do_become_nonbusy()` in "comedi_fops.c" but a previously scheduled
`waveform_ai_interrupt()` timer function will dereference that pointer
regardless, leading to the oops.
Fix it by replacing the `del_timer()` call in `waveform_ai_cancel()`
with `del_timer_sync()`.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Reported-by: Éric Piel <piel@delmic.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The minimum period was set to 357 ns, while the divider for these boards is 50
ns. This prevented to output at maximum speed as ni_ao_cmdtest() would return
357 but would not accept it.
Not sure why it was set to 357 ns (this was done before the git history,
which starts 5 years ago). My guess is that it comes from reading the
specification stating a 2.8 MHz rate (~ 357 ns). The latest
specification states a 2.86 MHz rate (~ 350 ns), which makes a lot
more sense.
Tested on a pci-6251.
Signed-off-by: Éric Piel <piel@delmic.com> Acked-By: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: drop hunk for a board that's not listed] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The ISY IWL 1000 USB WLAN stick with USB ID 050d:11f1 is a clone of
the Belkin F7D1101 V1 device.
Reported-by: Thomas Hartmann <hartmann@ict.tuwien.ac.at> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Thomas Hartmann <hartmann@ict.tuwien.ac.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As along the error path we do not correct the user pin-count for the
failure, we may end up with userspace believing that it has a pinned
object at offset 0 (when interrupted by a signal for example).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ioat does DMA memory sync with DMA_TO_DEVICE direction on a buffer allocated
for DMA_FROM_DEVICE dma, resulting in the following warning from dma debug.
Fixed the dma_sync_single_for_device() call to use the correct direction.
wait_event_interruptible function returns -ERESTARTSYS if it's
interrupted by a signal. Driver should check the return value
and handle this case properly.
In mwifiex_wait_queue_complete() routine, as we are now checking
wait_event_interruptible return value, the condition check is not
required. Also, we have removed mwifiex_cancel_pending_ioctl()
call to avoid a chance of sending second command to FW by other path
as soon as we clear current command node. FW can not handle two
commands simultaneously.
Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently even if association is failed "iw link" shows some
information about connected BSS and "Tx timeout" error is seen in
dmesg log.
This patch fixes below issues in the code to handle assoc failure
case correctly.
1) "status" variable in mwifiex_wait_queue_complete() is not
correctly updated. Hence driver doesn't inform cfg80211 stack
about association failure.
2) During association network queues are stopped but carrier is
not cleared, which gives Tx timeout error in failure case
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The USB core hub thread (khubd) is designed with external USB hubs in
mind. It expects that if a port status change bit is set, the hub will
continue to send a notification through the hub status data transfer.
Basically, it expects hub notifications to be level-triggered.
The xHCI host controller is designed to be edge-triggered on the logical
'OR' of all the port status change bits. When all port status change
bits are clear, and a new change bit is set, the xHC will generate a
Port Status Change Event. If another change bit is set in the same port
status register before the first bit is cleared, it will not send
another event.
This means that the hub code may lose port status changes because of
race conditions between clearing change bits. The user sees this as a
"dead port" that doesn't react to device connects.
The fix is to turn on port polling whenever a new change bit is set.
Once the USB core issues a hub status request that shows that no change
bits are set in any USB ports, turn off port polling.
We can't allow the USB core to poll the roothub for port events during
host suspend because if the PCI host is in D3cold, the port registers
will be all f's. Instead, stop the port polling timer, and
unconditionally restart it when the host resumes. If there are no port
change bits set after the resume, the first call to hub_status_data will
disable polling.
This patch should be backported to stable kernels with the first xHCI
support, 2.6.31 and newer, that include the commit 0f2a79300a1471cf92ab43af165ea13555c8b0a5 "USB: xhci: Root hub support."
There will be merge conflicts because the check for HC_STATE_SUSPENDED
was moved into xhci_suspend in 3.8.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
An empty port can transition to either Inactive or Compliance Mode if a
newly connected USB 3.0 device fails to link train. In that case, we
issue a warm reset. Some devices, such as John's Roseweil eusb3
enclosure, slip back into Compliance Mode after the warm reset.
The current warm reset code does not check for device connect status on
warm reset completion, and it incorrectly reports the warm reset
succeeded. This causes the USB core to attempt to send a Set Address
control transfer to a port in Compliance Mode, which will always fail.
Make hub_port_wait_reset check the current connect status and link state
after the warm reset completes. Return a failure status if the device
is disconnected or the link state is Compliance Mode or SS.Inactive.
Make hub_events disable the port if warm reset fails. This will disable
the port, and then bring it back into the RxDetect state. Make the USB
core ignore the connect change until the device reconnects.
Note that this patch does NOT handle connected devices slipping into the
Inactive state very well. This is a concern, because devices can go
into the Inactive state on U1/U2 exit failure. However, the fix for
that case is too large for stable, so it will be submitted in a separate
patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: John Covici <covici@ccs.covici.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The port reset code bails out early if the current connect status is
cleared (device disconnected). If we're issuing a hot reset, it may
also look at the link state before the reset is finished.
Section 10.14.2.6 of the USB 3.0 spec says that when a port enters the
Error state or Resetting state, the port connection bit retains the
value from the previous state. Therefore we can't trust it until the
reset finishes. Also, the xHCI spec section 4.19.1.2.5 says software
shall ignore the link state while the port is resetting, as it can be in
an unknown state.
The port state during reset is also unknown for USB 2.0 hubs. The hub
sends a reset signal by driving the bus into an SE0 state. This
overwhelms the "connect" signal from the device, so the port can't tell
whether anything is connected or not.
Fix the port reset code to ignore the port link state and current
connect bit until the reset finishes, and USB_PORT_STAT_RESET is
cleared.
Remove the check for USB_PORT_STAT_C_BH_RESET in the warm reset case,
because it's redundant. When the warm reset finishes, the port reset
bit will be cleared at the same time USB_PORT_STAT_C_BH_RESET is set.
Remove the now-redundant check for a cleared USB_PORT_STAT_RESET bit
in the code to deal with the finished reset.
This patch should be backported to all stable kernels.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
John's NEC 0.96 xHCI host controller needs a longer timeout for a warm
reset to complete. The logs show it takes 650ms to complete the warm
reset, so extend the hub reset timeout to 800ms to be on the safe side.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: John Covici <covici@ccs.covici.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If hot and warm reset fails, or a port remains in the Compliance Mode,
the USB core needs to be able to disable a USB 3.0 port. Unlike USB 2.0
ports, once the port is placed into the Disabled link state, it will not
report any new device connects. To get device connect notifications, we
need to put the link into the Disabled state, and then the RxDetect
state.
The xHCI driver needs to atomically clear all change bits on USB 3.0
port disable, so that we get Port Status Change Events for future port
changes. We could technically do this in the USB core instead of in the
xHCI roothub code, since the port state machine can't advance out of the
disabled state until we set the link state to RxDetect. However,
external USB 3.0 hubs don't need this code. They are level-triggered,
not edge-triggered like xHCI, so they will continue to send interrupt
events when any change bit is set. Therefore it doesn't make sense to
put this code in the USB core.
This patch is part of a series to fix several reports of infinite loops
on device enumeration failure. This includes John, when he boots with
a USB 3.0 device (Roseweil eusb3 enclosure) attached to his NEC 0.96
host controller. The fix requires warm reset support, so it does not
make sense to backport this patch to stable kernels without warm reset
support.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: John Covici <covici@ccs.covici.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When the USB core finishes reseting a USB device, the xHCI driver sends
a Reset Device command to the host. The xHC then updates its internal
representation of the USB device to the 'Default' device state. If the
device was already in the Default state, the xHC will complete the
command with an error status.
If a device needs to be reset several times during enumeration, the
second reset will always fail because of the xHCI Reset Device command.
This can cause issues during enumeration.
For example, usb_reset_and_verify_device calls into hub_port_init in a
loop. Say that on the first call into hub_port_init, the device is
successfully reset, but doesn't respond to several set address control
transfers. Then the port will be disabled, but the udev will remain in
tact. usb_reset_and_verify_device will call into hub_port_init again.
On the second call into hub_port_init, the device will be reset, and the
xHCI driver will issue a Reset Device command. This command will fail
(because the device is already in the Default state), and
usb_reset_and_verify_device will fail. The port will be disabled, and
the device won't be able to enumerate.
Fix this by ignoring the return value of the HCD reset_device callback.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB 3.0 hubs and roothubs will automatically transition a failed hot
reset to a warm (BH) reset. In that case, the warm reset change bit
will be set, and the link state change bit may also be set. Change
hub_port_finish_reset to unconditionally clear those change bits for USB
3.0 hubs. If these bits are not cleared, we may lose port change events
from the roothub.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK. If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).
The xHCI code to compute the NAK interval does not handle the special
case of zero properly. The current code unconditionally subtracts one
from bInterval and uses it as an exponent. This causes a very large
bInterval to be used, and warning messages like these will be printed:
usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes
This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.
This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math in
xhci_get_endpoint_interval()".
Reported-by: Vincent Pelletier <plr.vincent@gmail.com> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This is a very old bug, but there's nothing that prevents the
timer from running while the module is being removed when we
only do del_timer() instead of del_timer_sync().
The timer should normally not be running at this point, but
it's not clearly impossible (or we could just remove this.)
Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When a file system is mounted on a virtio-blk disk, we then remove it
and then reattach it, the reattached disk gets the same disk name and
ids as the hot removed one.
This leads to very nasty effects - mostly rendering the newly attached
device completely unusable.
Trying what happens when I do the same thing with a USB device, I saw
that the sd node simply doesn't get free'd when a device gets forcefully
removed.
Imitate the same behavior for vd devices. This way broken vd devices
simply are never free'd and newly attached ones keep working just fine.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 5c8a86e10a7c164f44537fabdc169fd8b4e7a440 (usb: musb: drop unneeded
musb_debug trickery) erroneously removed '\n' from the driver's banner.
Concatenate all the banner substrings while adding it back...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If we do have endpoints named like "ep-a" then bEndpointAddress is
counted internally by the gadget framework.
If we do have endpoints named like "ep-1" then bEndpointAddress is
assigned from the digit after "ep-".
If we do have both, then it is likely that after we used up the
"generic" endpoints we will use the digits and thus assign one
bEndpointAddress to multiple endpoints.
This theory can be proofed by using the completely enabled g_multi.
Without this patch, the mass storage won't enumerate and times out
because it shares endpoints with RNDIS.
This patch also adds fills up the endpoints list so we have in total
endpoints 1 to 15 in + out available while some of them are restricted
to certain types like BULK or ISO. Without this change the nokia gadget
won't load because the system does not provide enough (BULK) endpoints
but it did before ep-a - ep-f were removed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
blk_alloc_queue has already done a bdi_init, so do not bdi_init
again in aoeblk_gdalloc. The extra call causes list corruption
in the per-CPU backing dev info stats lists.
Affected users see console WARNINGs about list_del corruption on
percpu_counter_destroy when doing "rmmod aoe" or "aoeflush -a"
when AoE targets have been detected and initialized by the
system.
The patch below applies to v3.6.11, with its v47 aoe driver. It
is expected to apply to all currently maintained stable kernels
except 3.7.y. A related but different fix has been posted for
3.7.y.
References:
RedHat bugzilla ticket with original report
https://bugzilla.redhat.com/show_bug.cgi?id=853064
LKML discussion of bug and fix
http://thread.gmane.org/gmane.linux.kernel/1416336/focus=1416497
Reported-by: Josh Boyer <jwboyer@redhat.com> Signed-off-by: Ed Cashin <ecashin@coraid.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When system enters power off, the _PSW of Lid device is enabled.
But this may cause the system to reboot instead of power off.
A proper way to fix this is to always disable lid wakeup capability for S5.
References: https://bugzilla.kernel.org/show_bug.cgi?id=35262 Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
RFC 5961 5.2 [Blind Data Injection Attack].[Mitigation]
All TCP stacks MAY implement the following mitigation. TCP stacks
that implement this mitigation MUST add an additional input check to
any incoming segment. The ACK value is considered acceptable only if
it is in the range of ((SND.UNA - MAX.SND.WND) <= SEG.ACK <=
SND.NXT). All incoming segments whose ACK value doesn't satisfy the
above condition MUST be discarded and an ACK sent back.
Move tcp_send_challenge_ack() before tcp_ack() to avoid a forward
declaration.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Jerry Chu <hkchu@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We added support for RFC 5961 in latest kernels but TCP fails
to perform exhaustive check of ACK sequence.
We can update our view of peer tsval from a frame that is
later discarded by tcp_ack()
This makes timestamps enabled sessions vulnerable to injection of
a high tsval : peers start an ACK storm, since the victim
sends a dupack each time it receives an ACK from the other peer.
As tcp_validate_incoming() is called before tcp_ack(), we should
not peform tcp_replace_ts_recent() from it, and let callers do it
at the right time.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Nandita Dukkipati <nanditad@google.com> Cc: H.K. Jerry Chu <hkchu@google.com> Cc: Romain Francoise <romain@orebokech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Followup of commit 0c24604b68fc (tcp: implement RFC 5961 4.2)
As reported by Vijay Subramanian, we should send a challenge ACK
instead of a dup ack if a SYN flag is set on a packet received out of
window.
This permits the ratelimiting to work as intended, and to increase
correct SNMP counters.
Suggested-by: Vijay Subramanian <subramanian.vijay@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Vijay Subramanian <subramanian.vijay@gmail.com> Cc: Kiran Kumar Kella <kkiran@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Implement the RFC 5691 mitigation against Blind
Reset attack using SYN bit.
Section 4.2 of RFC 5961 advises to send a Challenge ACK and drop
incoming packet, instead of resetting the session.
Add a new SNMP counter to count number of challenge acks sent
in response to SYN packets.
(netstat -s | grep TCPSYNChallenge)
Remove obsolete TCPAbortOnSyn, since we no longer abort a TCP session
because of a SYN flag.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Kiran Kumar Kella <kkiran@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Implement the RFC 5691 mitigation against Blind
Reset attack using RST bit.
Idea is to validate incoming RST sequence,
to match RCV.NXT value, instead of previouly accepted
window : (RCV.NXT <= SEG.SEQ < RCV.NXT+RCV.WND)
If sequence is in window but not an exact match, send
a "challenge ACK", so that the other part can resend an
RST with the appropriate sequence.
Add a new sysctl, tcp_challenge_ack_limit, to limit
number of challenge ACK sent per second.
Add a new SNMP counter to count number of challenge acks sent.
(netstat -s | grep TCPChallengeACK)
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Kiran Kumar Kella <kkiran@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Stefan Hasko <hasko.stevo@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This happens, because sk_clone_lock initializes sk_refcnt to 2, and thus
a single sock_put() is not enough to free the memory. Additionally, things
like xfrm, memcg, cookie_values,... may have been initialized.
We have to free them properly.
This is fixed by forcing a call to tcp_done(), ending up in
inet_csk_destroy_sock, doing the final sock_put(). tcp_done() is necessary,
because it ends up doing all the cleanup on xfrm, memcg, cookie_values,
xfrm,...
Before calling tcp_done, we have to set the socket to SOCK_DEAD, to
force it entering inet_csk_destroy_sock. To avoid the warning in
inet_csk_destroy_sock, inet_num has to be set to 0.
As inet_csk_destroy_sock does a dec on orphan_count, we first have to
increase it.
Calling tcp_done() allows us to remove the calls to
tcp_clear_xmit_timer() and tcp_cleanup_congestion_control().
A similar approach is taken for dccp by calling dccp_done().
This is in the kernel since 093d282321 (tproxy: fix hash locking issue
when using port redirection in __inet_inherit_port()), thus since
version >= 2.6.37.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Modifying the huge pte's requires that all the underlying pte's be
modified.
Version 2: added missing flush_tlb_page()
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: sparclinux@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When gcc inlines a function, it does not mark it with the mcount
prologue, which in turn means that inlined functions are not traced
by the function tracer. But if CONFIG_OPTIMIZE_INLINING is set, then
gcc is allowed not to inline a function that is marked inline.
Depending on the options and the compiler, a function may or may
not be traced by the function tracer, depending on whether gcc
decides to inline a function or not. This has caused several
problems in the pass becaues gcc is not always consistent with
what it decides to inline between different gcc versions.
Some places should not be traced (like paravirt native_* functions)
and these are mostly marked as inline. When gcc decides not to
inline the function, and if that function should not be traced, then
the ftrace function tracer will suddenly break when it use to work
fine. This becomes even harder to debug when different versions of
gcc will not inline that function, making the same kernel and config
work for some gcc versions and not work for others.
By making all functions marked inline to not be traced will remove
the ambiguity that gcc adds when it comes to tracing functions marked
inline. All gcc versions will be consistent with what functions are
traced and having volatile working code will be removed.
Note, only the inline macro when CONFIG_OPTIMIZE_INLINING is set needs
to have notrace added, as the attribute __always_inline will force
the function to be inlined and then not traced.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
rt2x00: Don't let mac80211 send a BAR when an AMPDU subframe fails
To fix problem workaround by above commit use
IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAIL flag (see change log for
"mac80211: introduce IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAIL" patch).
Resolve: https://bugzilla.kernel.org/show_bug.cgi?id=42828 Bisected-by: Francisco Pina Martins <f.pinamartins@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit f0425beda4d404a6e751439b562100b902ba9c98 "mac80211: retry sending
failed BAR frames later instead of tearing down aggr" caused regression
on rt2x00 hardware (connection hangs). This regression was fixed by
commit be03d4a45c09ee5100d3aaaedd087f19bc20d01 "rt2x00: Don't let
mac80211 send a BAR when an AMPDU subframe fails". But the latter
commit caused yet another problem reported in
https://bugzilla.kernel.org/show_bug.cgi?id=42828#c22
After long discussion in this thread:
http://mid.gmane.org/20121018075615.GA18212@redhat.com
and testing various alternative solutions, which failed on one or other
setup, we have no other good fix for the issues like just revert both
mentioned earlier commits.
To do not affect other hardware which benefit from commit f0425beda4d404a6e751439b562100b902ba9c98, instead of reverting it,
introduce flag that when used will restore mac80211 behaviour before
the commit.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[replaced link with mid.gmane.org that has message-id] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There are connection stalls or very poor throughputs with rt2800
hardware using 802.11n in AP mode since patch "mac80211: retry sending
failed BAR frames later instead of tearing down aggr"[1][2].
Since rt2800 hardware is not able to correctly report the tx status of
BAR frames, this patch removes as workaround the existing error handling
on AP side, which lets mac80211 send a BAR when an AMPDU subframe fails.
As a result, most wifi clients (aside from Intel STAs on Windows)
instead will timeout now the reorder buffer and request the lost frame
again.
The correct solution would be, to tear down BA session on AP side.
This patch was born on the basis of "[RFT] rt2x00: Tear down BA
session on QoS frame failure"[3].
Signed-off-by: Andreas Hartmann <andihartmann@01019freenet.de> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
EPOLL_CTL_MOD sets the interest mask before calling f_op->poll() to
ensure events are not missed. Since the modifications to the interest
mask are not protected by the same lock as ep_poll_callback, we need to
ensure the change is visible to other CPUs calling ep_poll_callback.
We also need to ensure f_op->poll() has an up-to-date view of past
events which occured before we modified the interest mask. So this
barrier also pairs with the barrier in wq_has_sleeper().
This should guarantee either ep_poll_callback or f_op->poll() (or both)
will notice the readiness of a recently-ready/modified item.
This issue was encountered by Andreas Voellmy and Junchang(Jason) Wang in:
http://thread.gmane.org/gmane.linux.kernel/1408782/
Signed-off-by: Eric Wong <normalperson@yhbt.net> Cc: Hans Verkuil <hans.verkuil@cisco.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Davide Libenzi <davidel@xmailserver.org> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mauro Carvalho Chehab <mchehab@infradead.org> Cc: David Miller <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andreas Voellmy <andreas.voellmy@yale.edu> Tested-by: "Junchang(Jason) Wang" <junchang.wang@yale.edu> Cc: netdev@vger.kernel.org Cc: linux-fsdevel@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>