Rajendra Nayak [Fri, 25 Feb 2011 22:49:01 +0000 (15:49 -0700)]
OMAP4: DPLL: Add dpll api to control GATE_CTRL
On OMAP4, the dpll post divider outputs (MX outputs)
along with clockout_x2 output provide a way to allow/deny
hardware level autogating.
Allowing autoidle would mean that the hw would autogate
this clock when there is no dependency for it.
Denying idle would mean that this clock output will be
forced to stay enabled.
Add dpll api's to read/allow/deny idle control
for these dpll mx postdividers.
NOTE: The gatectrl bit set to 0 allows gatectrl,
and the bit set to 1 denies gatectrl.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: moved OMAP4-specific DPLL control code to
mach-omap2/dpll44xx.c; added some documentation for CLOCK_CLKOUTX2] Signed-off-by: Paul Walmsley <paul@pwsan.com>
Paul Walmsley [Fri, 25 Feb 2011 22:49:01 +0000 (15:49 -0700)]
OMAP2+: clock: autoidle as many clocks as possible if CONFIG_OMAP_RESET_CLOCKS
Attempt to enable autoidle for as many clocks as possible in the
OMAP2+-common CONFIG_OMAP_RESET_CLOCKS code. Currently, this only
enables DPLL autoidle for OMAP3/4 DPLLs; but future patches will
enable autoidle for other clocks and the OMAP2 DPLL/APLLs.
In the long run, we should probably get rid of
CONFIG_OMAP_RESET_CLOCKS, and unconditionally run the code that it
selects. Otherwise, the state of the clock tree won't match the
hardware state - this could result in clocks being enabled or disabled
unpredictably.
Based on a patch by Rajendra Nayak <rnayak@ti.com> that did this in
the pm34xx.c/pm44xx.c code.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Rajendra Nayak <rnayak@ti.com>
Rajendra Nayak [Fri, 25 Feb 2011 22:49:00 +0000 (15:49 -0700)]
OMAP: clock: Add allow_idle/deny_idle support in clkops
On OMAP various clock nodes (dpll's, mx post dividers, interface clocks)
support hardware level autogating which can be controlled from
software.
Support such functionality by adding two new function pointer
allow_idle and deny_idle in the clkops structure.
These function pointers can be populated for any clock
node which supports hardware level autogating.
Also add 2 new functions (omap_clk_enable_autoidle_all and
omap_clk_disable_autoidle_all) which can be called from
architecture specific PM core code, if hardware level
autogating (for all supported clock nodes) is to be
enabled or disabled.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use spinlock rather than mutex due to race; renamed functions;
functions now return ints] Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 25 Feb 2011 22:48:37 +0000 (15:48 -0700)]
omap3: dpll: Populate clkops for dpll1_ck
DPLL1 on omap3 is very similar to the rest of
the non-core dpll's.
Hence populate clkops_omap3_noncore_dpll_ops
as the clkops for it, instead of the
currently populated clkops_null.
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 25 Feb 2011 23:06:48 +0000 (16:06 -0700)]
OMAP: clockdomain: Arch specific funcs for clkdm_clk_enable/disable
Define the following architecture specific funtions for omap2/3/4
.clkdm_clk_enable
.clkdm_clk_disable
Convert the platform-independent framework to call these functions.
Also rename the api's by removing the omap2_ preamble.
Hence call omap2_clkdm_k_enable as clkdm_clk_enable and
omap2_clkdm_clk_disable as clkdm_clk_disable.a
Remove unused functions (_enable/_disable_hwsup) and unsed
headers from clockdomain.c file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 25 Feb 2011 23:06:48 +0000 (16:06 -0700)]
OMAP: clockdomain: Arch specific funcs for hwsup control of clkdm
Define the following architecture specific funtions for omap2/3/4
.clkdm_allow_idle
.clkdm_deny_idle
Convert the platform-independent framework to call these functions.
Also rename the api's by removing the omap2_ preamble.
Hence call omap2_clkdm_allow_idle as clkdm_allow_idle and
omap2_clkdm_deny_idle as clkdm_deny_idle.
Make the _clkdm_add_autodeps and _clkdm_del_autodeps as non-static
so they can be accessed from OMAP2/3 platform specific code.
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 25 Feb 2011 23:06:47 +0000 (16:06 -0700)]
OMAP: clockdomain: Arch specific funcs for sleep/wakeup of clkdm
Define the following architecture specific funtions for omap2/3/4
.clkdm_sleep
.clkdm_wakeup
Convert the platform-independent framework to call these functions.
Also rename the api's by removing the omap2_ preamble.
Hence call omap2_clkdm_wakeup as clkdm_wakeup and
omap2_clkdm_sleep as clkdm_sleep.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: fixed omap3_clkdm_clear_all_sleepdeps() and
omap2_clkdm_clear_all_wkdeps() to test against the correct
loop termination condition; thanks to Kevin Hilman for finding and
helping fix] Cc: Kevin Hilman <khilman@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 25 Feb 2011 23:06:47 +0000 (16:06 -0700)]
OMAP: clockdomain: Arch specific funcs to handle deps
Define the following architecture specific funtions for omap2/3
.clkdm_add_wkdep
.clkdm_del_wkdep
.clkdm_read_wkdep
.clkdm_clear_all_wkdeps
.clkdm_add_sleepdep
.clkdm_del_sleepdep
.clkdm_read_sleepdep
.clkdm_clear_all_sleepdeps
Convert the platform-independent framework to call these functions.
With this also move the clkdm lookups for all wkdep_srcs and
sleepdep_srcs at clkdm_init.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: fixed loop termination conditions in omap*_clkdm_clear_all_*();
thanks to Kevin Hilman for finding and helping fix those bugs; also
avoid re-resolving clockdomains during init; abstracted out clkdm_dep walk] Cc: Kevin Hilman <khilman@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rajendra Nayak [Fri, 25 Feb 2011 23:06:47 +0000 (16:06 -0700)]
OMAP: clockdomain: Infrastructure to put arch specific code
Put infrastructure in place, so arch specific func pointers
can be hooked up to the platform-independent part of the
framework.
This is in preparation of splitting the clockdomain framework into
platform-independent part (for all omaps) and platform-specific
parts.
Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for Display Sub System applicable for OMAP3430 and
OMAP36xx. DSS is also considered as an IP as DISPC, RFBI and named as dss_core.
For all the IP modules in DSS, same clock is needed for enabling. Hwmod sees
DSS IPs as independent IPs, so same clock has to be repeated for .main_clk in
each IP.
This patch defines separate hwmod databases for OMAP3430ES1 and (OMAP3430ES2 and
OMAP36xx) as OMAP3430ES1 does not have IDLEST bit to poll on for dss IP, and also
the firewall regions are different between 3430es1 and later.
Reviewed-by: Kevin Hilman <khilman@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Sumit Semwal <sumit.semwal@ti.com> Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for OMAP2430 Display Sub System. Since DSS is also considered as an
IP as DISPC, RFBI, name it as dss_core.
Acked-by: Benoit Cousson <b-cousson@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Sumit Semwal <sumit.semwal@ti.com> Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for OMAP2420 Display Sub System,. Since DSS is also considered as an
IP as DISPC, RFBI, name it as dss_core.
Acked-by: Benoit Cousson <b-cousson@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com> Tested-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Sumit Semwal <sumit.semwal@ti.com> Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Govindraj.R [Wed, 2 Feb 2011 12:22:15 +0000 (17:52 +0530)]
OMAP: runtime: McSPI driver runtime conversion
McSPI runtime conversion.
Changes involves:
1) remove clock framework apis to use runtime framework apis.
2) context restore from runtime resume which is a callback for get_sync.
3) Remove SYSCONFIG(sysc) register handling
(a) Remove context save and restore of sysc reg and remove soft reset
done from sysc reg as this will be done with hwmod framework.
(b) Also cleanup sysc reg bit macros.
4) Rename the omap2_mcspi_reset function to omap2_mcspi_master_setup
function as with hwmod changes soft reset will be done in
hwmod framework itself and use the return value from clock
enable function to return for failure scenarios.
Signed-off-by: Charulatha V <charu@ti.com> Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: Partha Basak <p-basak2@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Charulatha V [Wed, 2 Feb 2011 12:22:14 +0000 (17:52 +0530)]
OMAP: devices: Modify McSPI device to adapt to hwmod framework
Cleans up all base address definitions for omap_mcspi
and adapts the device registration and driver to hwmod framework.
Changes involves:
1) Removing all base address macro defines.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute(number of chipselect).
3) Appending base address with pdata reg_offset for omap4 boards.
For omap4 all regs used in driver deviate with reg_offset_macros
defined with an value of 0x100. So pass this offset through pdata
and append the same to base address retrieved from hwmod data file
and we are not mapping *_HL_* regs which are not used in driver.
Signed-off-by: Charulatha V <charu@ti.com> Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: Partha Basak <p-basak2@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Charulatha V [Thu, 17 Feb 2011 17:53:10 +0000 (09:53 -0800)]
OMAP3: hwmod data: Add McSPI
Update omap3 hwmod data file with McSPI info.
Signed-off-by: Charulatha V <charu@ti.com> Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Charulatha V [Thu, 17 Feb 2011 17:53:10 +0000 (09:53 -0800)]
OMAP2430: hwmod data: Add McSPI
Update the 2430 hwmod data file with McSPI info.
Signed-off-by: Charulatha V <charu@ti.com> Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Charulatha V [Thu, 17 Feb 2011 17:53:09 +0000 (09:53 -0800)]
OMAP2420: hwmod data: Add McSPI
Update the omap2420 hwmod data with the McSPI info.
Add a device attribute structure which will be used
for passing number of chipselects from hwmod data.
Add revision macros to be passed from rev field from
hwmod.
Signed-off-by: Charulatha V <charu@ti.com> Signed-off-by: Govindraj.R <govindraj.raja@ti.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Reviewed-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Simon Que [Thu, 17 Feb 2011 17:52:03 +0000 (09:52 -0800)]
omap: add hwspinlock device
Build and register an hwspinlock platform device.
Although only OMAP4 supports the hardware spinlock module (for now),
it is still safe to run this initcall on all omaps, because hwmod lookup
will simply fail on hwspinlock-less platforms.
Signed-off-by: Simon Que <sque@ti.com> Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com> Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Cc: Benoit Cousson <b-cousson@ti.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Simon Que [Thu, 17 Feb 2011 17:52:03 +0000 (09:52 -0800)]
drivers: hwspinlock: add OMAP implementation
Add hwspinlock support for the OMAP4 Hardware Spinlock device.
The Hardware Spinlock device on OMAP4 provides hardware assistance
for synchronization between the multiple processors in the system
(dual Cortex-A9, dual Cortex-M3 and a C64x+ DSP).
[ohad@wizery.com: adapt to hwspinlock framework, tidy up] Signed-off-by: Simon Que <sque@ti.com> Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com> Signed-off-by: Krishnamoorthy, Balaji T <balajitk@ti.com> Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Cc: Benoit Cousson <b-cousson@ti.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Paul Walmsley <paul@pwsan.com> Cc: Russell King <linux@arm.linux.org.uk> Signed-off-by: Tony Lindgren <tony@atomide.com>
Ohad Ben-Cohen [Thu, 17 Feb 2011 17:52:03 +0000 (09:52 -0800)]
drivers: hwspinlock: add framework
Add a platform-independent hwspinlock framework.
Hardware spinlock devices are needed, e.g., in order to access data
that is shared between remote processors, that otherwise have no
alternative mechanism to accomplish synchronization and mutual exclusion
operations.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Cc: Hari Kanigeri <h-kanigeri2@ti.com> Cc: Benoit Cousson <b-cousson@ti.com> Cc: Kevin Hilman <khilman@ti.com> Cc: Grant Likely <grant.likely@secretlab.ca> Cc: Paul Walmsley <paul@pwsan.com> Cc: Russell King <linux@arm.linux.org.uk> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
Benoit Cousson [Thu, 17 Feb 2011 12:41:05 +0000 (12:41 +0000)]
OMAP4: hwmod data: Add USBOTG
OMAP4 hwmod data structures are populated with base address, L3 and L4
interface clocks, IRQs and sysconfig register details.
As per OMAP USBOTG specification, need to configure the USBOTG
to smart idle/standby or no idle/standby during data transfer and
force idle/standby when not in use to support retention and offmode.
By setting HWMOD_SWSUP_SIDLE and HWMOD_SWSUP_MSTANDBY flags,framework
will take care of configuring to no idle/standby when module is enabled
and force idle/standby when idled.
Signed-off-by: Cousson, Benoit <b-cousson@ti.com> Signed-off-by: Hema HK <hemahk@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
[b-cousson@ti.com: Fix position, opt_clk, and author]
Benoit Cousson [Mon, 31 Jan 2011 14:50:30 +0000 (14:50 +0000)]
OMAP4: hwmod data: Add McBSP
Add mcbsp data including a revision member in hwmod_class in
order to provide mcbsp revision information in different omap.
Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Charulatha V <charu@ti.com>
[b-cousson@ti.com: Remove the mcbsp4 memory name, re-order
properly the structures]
Benoit Cousson [Tue, 25 Jan 2011 22:01:00 +0000 (22:01 +0000)]
OMAP4: hwmod data: Add DMIC
Add HWMOD entries for the OMAP DMIC. The HWMOD entires define the system
resource requirements for the driver such as DMA addresses, channels,
and IRQ's. Placing this information in the HWMOD database allows for
more generic drivers to be written and having the specific implementation
details defined in HWMOD.
Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: David Lambert <dlambert@ti.com>
[b-cousson@ti.com: Change the wrong hwmod name,
add missing flag and re-order structures]
Benoit Cousson [Wed, 2 Feb 2011 19:27:21 +0000 (19:27 +0000)]
OMAP4: hwmod data: Add mailbox
Mailbox hwmod data for omap4.
Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
[b-cousson@ti.com: Re-order the structures
and remove the irq line name]
Add dss, dispc, dsi1, dsi2, hdmi, rfbi and venc hwmods.
In OMAP4 there are severals IPs that can be reached by differents
interconnect paths depending of the access initiator (MPU vs. SDMA).
In the case of the DSS, both L3 direct path and L4 CFG path can be
used to access all the DSS IPs. The two ocp_ip already exists to support
the two address spaces.
+------------+-- L3_MAIN --+ MPU
IP | |
+-- L4_CFG --+
L3 main address range is specified first, since it is used by default.
dss is also considered as an IP as dispc, rfbi, and named as dss_core.
Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Mayuresh Janorkar <mayur@ti.com> Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com> Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
[b-cousson@ti.com: Re-organize structures to match file
convention and remove irq entry from dss_hwmod]
Benoit Cousson [Fri, 11 Feb 2011 11:17:14 +0000 (11:17 +0000)]
OMAP4: hwmod data: Add timer
Add the data for the 11 timers IPs.
OMAP4 contains two differents IP variants for the timers:
- 8 x regular timer (3, 4, 5, 6, 7, 8, 9 & 11)
- 3 x 1ms timer (1, 2 & 10)
The regular timers registers programming model was changed due to the
adaptation to the new IP interface. Unfortunately the 1ms version
still use the previous programming model. The driver will have
to take care of theses differences.
Please note that the capability and the partitioning is also
different depending of the instance.
- timer 1 is inside the wakeup domain
- timers 5, 6, 7 & 8 are inside in the ABE (audio backend)
- timers 2, 3, 4, 9, 10 & 11 are inside the PER power domain
The timer was previously named gptimerX or dmtimerX, it is
now simply named timerX.
Signed-off-by: Benoit Cousson <b-cousson@ti.com> Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
[b-cousson@ti.com: Fix alignement in class attribute,
re-order flags and update the changelog]
Hema HK [Thu, 17 Feb 2011 06:37:21 +0000 (12:07 +0530)]
OMAP2+: musb: hwmod adaptation for musb registration
Using omap_device_build API instead of platform_device_register for
OMAP2430,OMAP3xxx, OMAP4430 and AM35x musb device registration.
The device specific resources defined in centralized
database will be used.
Signed-off-by: Hema HK <hemahk@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Cousson, Benoit <b-cousson@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Hema HK [Thu, 17 Feb 2011 06:37:19 +0000 (12:07 +0530)]
AM35xx: hwmod data: Add USBOTG
AM35xx hwmod data structures are populated for USBOTG with base address,
L3 and L4 interface clocks and IRQ.
Signed-off-by: Hema HK <hemahk@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Cousson, Benoit <b-cousson@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Hema HK [Thu, 17 Feb 2011 06:37:18 +0000 (12:07 +0530)]
OMAP3xxx: hwmod data: Add USBOTG
OMAP3 hwmod data structures are populated for USBOTG with base address,
L3 and L4 interface clocks, IRQs and sysconfig register details.
This is applicable for OMAP3430 amd OMAP3630.
As per OMAP USBOTG specification, need to configure the USBOTG
to smart idle/standby or no idle/standby during data transfer and
force idle/standby when not in use to support retention and offmode.
By setting HWMOD_SWSUP_SIDLE and HWMOD_SWSUP_MSTANDBY flags, framework
will take care of configuring to no idle/standby when module is enabled
and force idle/standby when idled.
Signed-off-by: Hema HK <hemahk@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Cousson, Benoit <b-cousson@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Hema HK [Thu, 17 Feb 2011 06:37:17 +0000 (12:07 +0530)]
OMAP2430: hwmod data: Add USBOTG
OMAP2430 hwmod data structures are populated with base address, L3 and L4
interface clocks, IRQs and sysconfig register details.
As per OMAP USBOTG specification, need to configure the USBOTG
to smart idle/standby or no idle/standby during data transfer and
force idle/standby when not in use to support retention and off-mode.
By setting HWMOD_SWSUP_SIDLE and HWMOD_SWSUP_MSTANDBY flags, framework
will take care of configuring to no idle/standby when module is enabled
and force idle/standby when suspended.
Signed-off-by: Hema HK <hemahk@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Cc: Cousson, Benoit <b-cousson@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Anand Gadiyar [Wed, 16 Feb 2011 11:17:19 +0000 (16:47 +0530)]
arm: omap4: 4430sdp: drop ehci support
Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.
Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).
Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.
So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Cc: Keshava Munegowda <keshava_mgowda@ti.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Anand Gadiyar [Wed, 16 Feb 2011 10:12:15 +0000 (15:42 +0530)]
arm: omap4: usb: explicitly configure MUSB pads
Use the mux framework APIs to explicitly configure
the MUSB pads. The MUSB controller in OMAP4 can use
either the old ULPI interface, or the new internal PHY.
Configure the pads accordingly.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Hema HK [Wed, 16 Feb 2011 12:04:40 +0000 (17:34 +0530)]
usb: musb: AM35x: moving internal phy functions out of usb_musb.c file
Moved all the board specific internal PHY functions out of usb_musb.c file
as this file is shared between the OMAP2+ and AM35xx platforms.
There exists a file which has the functions specific to internal PHY
used for OMAP4 platform. Moved all phy specific functions to this file
and passing these functions through board data in the board file.
Signed-off-by: Hema HK <hemahk@ti.com> Cc: Paul Walmsley <paul@pwsan.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Benoit Cousson [Wed, 2 Feb 2011 12:04:36 +0000 (12:04 +0000)]
OMAP4: hwmod data: Add hwspinlock
Add hwspinlock hwmod data for OMAP4 chip
Signed-off-by: Cousson, Benoit <b-cousson@ti.com> Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com> Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Cc: Paul Walmsley <paul@pwsan.com>
[b-cousson@ti.com: Move the data to keep the original
order and add missing SIDLE_SMART_WKUP flag]
Hemant Pedanekar [Wed, 16 Feb 2011 16:31:39 +0000 (08:31 -0800)]
TI816X: Update common omap platform files
This patch updates the common platform files with TI816X support.
The approach taken in this patch is to add TI816X as part of OMAP3 variant where
the cpu class is considered as OMAP34XX and the type is TI816X. This means, both
cpu_is_omap34xx() and cpu_is_ti816x() checks return success on TI816X.
A kernel config option CONFIG_SOC_OMAPTI816X is added under OMAP3 to include
support for TI816X build.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com> Reviewed-by: Kevin Hilman <khilman@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Wed, 16 Feb 2011 01:51:18 +0000 (17:51 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: set flow handler for secondary interrupt controller of 5249
m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
m68knommu: fix dereference of port.tty
m68knommu: add missing linker __modver section
m68knommu: fix mis-named variable int set_irq_chip loop
m68knommu: add optimize memmove() function
m68k: remove arch specific non-optimized memcmp()
m68knommu: fix use of un-defined _TIF_WORK_MASK
m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
m68knommu: fix m548x_wdt.c compilation after headers renaming
m68knommu: Remove dependencies on nonexistent M68KNOMMU
Greg Ungerer [Tue, 8 Feb 2011 04:40:44 +0000 (14:40 +1000)]
m68knommu: fix mis-named variable int set_irq_chip loop
Compiling for 68360 targets gives:
CC arch/m68knommu/platform/68360/ints.o
arch/m68knommu/platform/68360/ints.c: In function ‘init_IRQ’:
arch/m68knommu/platform/68360/ints.c:135:16: error: ‘irq’ undeclared (first use in this function)
arch/m68knommu/platform/68360/ints.c:135:16: note: each undeclared identifier is reported only once for each function it appears in
Greg Ungerer [Thu, 3 Feb 2011 11:58:39 +0000 (21:58 +1000)]
m68knommu: add optimize memmove() function
Add an m68k/coldfire optimized memmove() function for the m68knommu arch.
This is the same function as used by m68k. Simple speed tests show this
is faster once buffers are larger than 4 bytes, and significantly faster
on much larger buffers (4 times faster above about 100 bytes).
This also goes part of the way to fixing a regression caused by commit ea61bc461d09e8d331a307916530aaae808c72a2 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memmove() fucntion
defined, since there was none in the m68knommu/lib functions.
Greg Ungerer [Thu, 3 Feb 2011 11:31:20 +0000 (21:31 +1000)]
m68k: remove arch specific non-optimized memcmp()
The m68k arch implements its own memcmp() function. It is not optimized
in any way (it is the most strait forward coding of memcmp you can get).
Remove it and use the kernels standard memcmp() implementation.
This also goes part of the way to fixing a regression caused by commit ea61bc461d09e8d331a307916530aaae808c72a2 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memcmp() function
defined, since there is none in the m68knommu/lib functions.
Linus Torvalds [Tue, 15 Feb 2011 23:25:33 +0000 (15:25 -0800)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
drm/radeon/kms: hopefully fix pll issues for real (v3)
drm/radeon/kms: add bounds checking to avivo pll algo
drm: fix wrong usages of drm_device in DRM Developer's Guide
drm/radeon/kms: fix a few more atombios endian issues
drm/radeon/kms: improve 6xx/7xx CS error output
drm/radeon/kms: check AA resolve registers on r300
drm/radeon/kms: fix tracking of BLENDCNTL, COLOR_CHANNEL_MASK, and GB_Z on r300
drm/radeon/kms: use linear aligned for evergreen/ni bo blits
drm/radeon/kms: use linear aligned for 6xx/7xx bo blits
drm/radeon: fix race between GPU reset and TTM delayed delete thread.
drm/radeon/kms: evergreen/ni big endian fixes (v2)
drm/radeon/kms: 6xx/7xx big endian fixes
drm/radeon/kms: atombios big endian fixes
drm/radeon: 6xx/7xx non-kms endian fixes
drm/radeon/kms: optimize CS state checking for r100->r500
drm: do not leak kernel addresses via /proc/dri/*/vma
drm/radeon/kms: add connector table for mac g5 9600
radeon mkregtable: Add missing fclose() calls
drm/radeon/kms: fix interlaced modes on dce4+
drm/radeon: fix memory debugging since d961db75ce86a84f1f04e91ad1014653ed7d9f46
...
Linus Torvalds [Tue, 15 Feb 2011 23:25:11 +0000 (15:25 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
pci: use security_capable() when checking capablities during config space read
Andrea Arcangeli [Tue, 15 Feb 2011 18:02:45 +0000 (19:02 +0100)]
thp: prevent hugepages during args/env copying into the user stack
Transparent hugepages can only be created if rmap is fully
functional. So we must prevent hugepages to be created while
is_vma_temporary_stack() is true.
This also optmizes away some harmless but unnecessary setting of
khugepaged_scan.address and it switches some BUG_ON to VM_BUG_ON.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Acked-by: Rik van Riel <riel@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 15 Feb 2011 23:19:45 +0000 (15:19 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI / Video: Probe for output switch method when searching video devices.
ACPI / Wakeup: Enable button GPEs unconditionally during initialization
ACPI / ACPICA: Avoid crashing if _PRW is defined for the root object
ACPI: Fix acpi_os_read_memory() and acpi_os_write_memory() (v2)
Linus Torvalds [Tue, 15 Feb 2011 20:07:35 +0000 (12:07 -0800)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (21 commits)
dmaengine: add slave-dma maintainer
dma: ipu_idmac: do not lose valid received data in the irq handler
dmaengine: imx-sdma: fix up param for the last BD in sdma_prep_slave_sg()
dmaengine: imx-sdma: correct sdmac->status in sdma_handle_channel_loop()
dmaengine: imx-sdma: return sdmac->status in sdma_tx_status()
dmaengine: imx-sdma: set sdmac->status to DMA_ERROR in err_out of sdma_prep_slave_sg()
dmaengine: imx-sdma: remove IMX_DMA_SG_LOOP handling in sdma_prep_slave_sg()
dmaengine i.MX dma: initialize dma capabilities outside channel loop
dmaengine i.MX DMA: do not initialize chan_id field
dmaengine i.MX dma: check sg entries for valid addresses and lengths
dmaengine i.MX dma: set maximum segment size for our device
dmaengine i.MX SDMA: reserve channel 0 by not registering it
dmaengine i.MX SDMA: initialize dma capabilities outside channel loop
dmaengine i.MX SDMA: do not initialize chan_id field
dmaengine i.MX sdma: check sg entries for valid addresses and lengths
dmaengine i.MX sdma: set maximum segment size for our device
DMA: PL08x: fix channel pausing to timeout rather than lockup
DMA: PL08x: fix infinite wait when terminating transfers
dmaengine: imx-sdma: fix inconsistent naming in sdma_assign_cookie()
dmaengine: imx-sdma: propagate error in sdma_probe() instead of returning 0
...
Linus Torvalds [Tue, 15 Feb 2011 20:06:38 +0000 (12:06 -0800)]
Merge branch 'for-2.6.38' of git://linux-nfs.org/~bfields/linux
* 'for-2.6.38' of git://linux-nfs.org/~bfields/linux:
nfsd: break lease on unlink due to rename
nfsd4: acquire only one lease per file
nfsd4: modify fi_delegations under recall_lock
nfsd4: remove unused deleg dprintk's.
nfsd4: split lease setting into separate function
nfsd4: fix leak on allocation error
nfsd4: add helper function for lease setup
nfsd4: split up nfsd_break_deleg_cb
NFSD: memory corruption due to writing beyond the stat array
NFSD: use nfserr for status after decode_cb_op_status
nfsd: don't leak dentry count on mnt_want_write failure
Linus Torvalds [Tue, 15 Feb 2011 18:19:18 +0000 (10:19 -0800)]
Merge branches 'core-fixes-for-linus' and 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Revert "lockdep, timer: Fix del_timer_sync() annotation"
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timer debug: Hide kernel addresses via %pK in /proc/timer_list
Linus Torvalds [Tue, 15 Feb 2011 18:18:48 +0000 (10:18 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix text_poke_smp_batch() deadlock
perf tools: Fix thread_map event synthesizing in top and record
watchdog, nmi: Lower the severity of error messages
ARM: oprofile: Fix backtraces in timer mode
oprofile: Fix usage of CONFIG_HW_PERF_EVENTS for oprofile_perf_init and friends
Linus Torvalds [Tue, 15 Feb 2011 18:18:29 +0000 (10:18 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, dmi, debug: Log board name (when present) in dmesg/oops output
x86, ioapic: Don't warn about non-existing IOAPICs if we have none
x86: Fix mwait_usable section mismatch
x86: Readd missing irq_to_desc() in fixup_irq()
x86: Fix section mismatch in LAPIC initialization
Linus Torvalds [Tue, 15 Feb 2011 16:06:36 +0000 (08:06 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
get rid of nameidata_dentry_drop_rcu() calling nameidata_drop_rcu()
drop out of RCU in return_reval
split do_revalidate() into RCU and non-RCU cases
in do_lookup() split RCU and non-RCU cases of need_revalidate
nothing in do_follow_link() is going to see RCU
task_show_regs used to be a debugging aid in the early bringup days
of Linux on s390. /proc/<pid>/status is a world readable file, it
is not a good idea to show the registers of a process. The only
correct fix is to remove task_show_regs.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Wright [Tue, 15 Feb 2011 01:21:49 +0000 (17:21 -0800)]
pci: use security_capable() when checking capablities during config space read
This reintroduces commit 47970b1b which was subsequently reverted
as f00eaeea. The original change was broken and caused X startup
failures and generally made privileged processes incapable of reading
device dependent config space. The normal capable() interface returns
true on success, but the LSM interface returns 0 on success. This thinko
is now fixed in this patch, and has been confirmed to work properly.
So, once again...Eric Paris noted that commit de139a3 ("pci: check caps
from sysfs file open to read device dependent config space") caused the
capability check to bypass security modules and potentially auditing.
Rectify this by calling security_capable() when checking the open file's
capabilities for config space reads.
Reported-by: Eric Paris <eparis@redhat.com> Tested-by: Dave Young <hidave.darkstar@gmail.com> Acked-by: James Morris <jmorris@namei.org> Cc: Dave Airlie <airlied@gmail.com> Cc: Alex Riesen <raa.lkml@gmail.com> Cc: Sedat Dilek <sedat.dilek@googlemail.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: James Morris <jmorris@namei.org>
Naga Chumbalkar [Mon, 14 Feb 2011 22:47:17 +0000 (22:47 +0000)]
x86, dmi, debug: Log board name (when present) in dmesg/oops output
The "Type 2" SMBIOS record that contains Board Name is not
strictly required and may be absent in the SMBIOS on some
platforms.
( Please note that Type 2 is not listed in Table 3 in Sec 6.2
("Required Structures and Data") of the SMBIOS v2.7
Specification. )
Use the Manufacturer Name (aka System Vendor) name.
Print Board Name only when it is present.
Before the fix:
(i) dmesg output: DMI: /ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2170, comm: bash Not tainted 2.6.38-rc4+ #3 /ProLiant DL380 G6
After the fix:
(i) dmesg output: DMI: HP ProLiant DL380 G6, BIOS P62 01/29/2011
(ii) oops output: Pid: 2278, comm: bash Not tainted 2.6.38-rc4+ #4 HP ProLiant DL380 G6
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com> Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: <stable@kernel.org> # .3x - good for debugging, please apply as far back as it applies cleanly
LKML-Reference: <20110214224423.2182.13929.sendpatchset@nchumbalkar.americas.hpqcorp.net> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Paul Bolle [Mon, 14 Feb 2011 21:52:38 +0000 (22:52 +0100)]
x86, ioapic: Don't warn about non-existing IOAPICs if we have none
mp_find_ioapic() prints errors like:
ERROR: Unable to locate IOAPIC for GSI 13
if it can't find the IOAPIC that manages that specific GSI. I
see errors like that at every boot of a laptop that apparently
doesn't have any IOAPICs.
But if there are no IOAPICs it doesn't seem to be an error that
none can be found. A solution that gets rid of this message is
to directly return if nr_ioapics (still) is zero. (But keep
returning -1 in that case, so nothing breaks from this change.)
The call chain that generates this error is:
pnpacpi_allocated_resource()
case ACPI_RESOURCE_TYPE_IRQ:
pnpacpi_parse_allocated_irqresource()
acpi_get_override_irq()
mp_find_ioapic()
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tony Lindgren [Mon, 14 Feb 2011 23:40:20 +0000 (15:40 -0800)]
omap2+: Fix omap_serial_early_init to work with init_early hook
The new init_early hook happens at the end of setup_arch,
which is too early for kzalloc. However, there's no need
to call omap_serial_early_init that early, so fix this
by setting it up as a core_initcall.
Signed-off-by: Tony Lindgren <tony@atomide.com> Tested-by: Kevin Hilman <khilman@ti.com>
Alex Deucher [Mon, 14 Feb 2011 16:43:11 +0000 (11:43 -0500)]
drm/radeon/kms: hopefully fix pll issues for real (v3)
The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.
v2: testing options
v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.
omap: McBSP: Remove unused audio macros in mcbsp.h
Some macros defined in mcbsp.h related to audio, which are never being used
is removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Reviewed-by: Charulatha V <charu@ti.com> Cc: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: G, Manjunath Kondaiah <manjugk@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Mon, 14 Feb 2011 22:49:29 +0000 (14:49 -0800)]
Merge branch 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6657/1: hw_breakpoint: fix ptrace breakpoint advertising on unsupported arch
ARM: 6656/1: hw_breakpoint: avoid UNPREDICTABLE behaviour when reading DBGDSCR
ARM: 6658/1: collie: do actually pass locomo_info to locomo driver
ARM: 6659/1: Thumb-2: Make CONFIG_OABI_COMPAT depend on !CONFIG_THUMB2_KERNEL
ARM: 6654/1: perf/oprofile: fix off-by-one in stack check
ARM: fixup SMP alternatives in modules
ARM: make SWP emulation explicit on !CPU_USE_DOMAINS
ARM: Avoid building unsafe kernels on OMAP2 and MX3
ARM: pxa: Properly configure PWM period for palm27x
ARM: pxa: only save/restore registers when pm functions are defined
ARM: pxa/colibri: use correct SD detect pin
ARM: pxa: fix mfpr_sync to read from valid offset
Tsutomu Itoh [Mon, 14 Feb 2011 00:45:29 +0000 (00:45 +0000)]
Btrfs: check return value of alloc_extent_map()
I add the check on the return value of alloc_extent_map() to several places.
In addition, alloc_extent_map() returns only the address or NULL.
Therefore, check by IS_ERR() is unnecessary. So, I remove IS_ERR() checking.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
space_args.space_slots is an unsigned 64-bit type controlled by a
possibly unprivileged caller. The comparison as a signed int type
allows providing values that are treated as negative and cause the
subsequent allocation size calculation to wrap, or be truncated to 0.
By providing a size that's truncated to 0, kmalloc() will return
ZERO_SIZE_PTR. It's also possible to provide a value smaller than the
slot count. The subsequent loop ignores the allocation size when
copying data in, resulting in a heap overflow or write to ZERO_SIZE_PTR.
The fix changes the slot count type and comparison typecast to u64,
which prevents truncation or signedness errors, and also ensures that we
don't copy more data than we've allocated in the subsequent loop. Note
that zero-size allocations are no longer possible since there is already
an explicit check for space_args.space_slots being 0 and truncation of
this value is no longer an issue.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com> Signed-off-by: Josef Bacik <josef@redhat.com> Reviewed-by: Josef Bacik <josef@redhat.com> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Mon, 14 Feb 2011 18:10:07 +0000 (10:10 -0800)]
Merge branch 'rtc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'rtc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
RTC: Fix minor compile warning
RTC: Convert rtc drivers to use the alarm_irq_enable method
RTC: Fix rtc driver ioctl specific shortcutting
Chris Mason [Mon, 14 Feb 2011 17:52:08 +0000 (12:52 -0500)]
Btrfs: don't release pages when we can't clear the uptodate bits
Btrfs tracks uptodate state in an rbtree as well as in the
page bits. This is supposed to enable us to use block sizes other than
the page size, but there are a few parts still missing before that
completely works.
But, our readpage routine trusts this additional range based tracking
of uptodateness, much in the same way the buffer head up to date bits
are trusted for the other filesystems.
The problem is that sometimes we need to allocate memory in order to
split records in the rbtree, even when we are just clearing bits. This
can be difficult when our clearing function is called GFP_ATOMIC, which
can happen in the releasepage path.
So, what happens today looks like this:
releasepage called with GFP_ATOMIC
btrfs_releasepage calls clear_extent_bit
clear_extent_bit fails to allocate ram, leaving the up to date bit set
btrfs_releasepage returns success
The end result is the page being gone, but btrfs thinking the range is
up to date. Later on if someone tries to read that same page, the
btrfs readpage code will return immediately thinking the page is already
up to date.
This commit fixes things to fail the releasepage when we can't clear the
extent state bits. It covers both data pages and metadata tree blocks.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
projects / linux-beck.git / log