Robin H. Johnson [Mon, 24 Oct 2011 22:30:08 +0000 (22:30 +0000)]
[SCSI] mv_sas: OCZ RevoDrive3 & zDrive R4 support
In the OCZ RevoDrive3/zDrive R4 series, the "OCZ SuperScale Storage
Controller" with "Virtualized Controller Architecture 2.0" really seems
to be a Marvell 88SE9485 part, with OCZ firmware/BIOS.
Developed and tested on OCZ RevoDrive3 120GB [PCI 1b85:1021]
All of this because a friend recently bought a OCZ RevoDrive3 and was
bitten by the lack of Linux support.
Notes from testing:
-------------------
- SMART works.
- VPD Device Identification is "OCZ-REVODRIVE3"
- Thin provisioning/TRIM seems to be implemented as WRITE SAME UNMAP,
with deterministic (non-zero) read after TRIM, but I'm not sure if it
works 100% in my testing.
- Some of the tuning in the firmware seems to ensure much better
performance when in a RAID0 setup than using the two devices
seperately.
I have not tested booting from the SSD, because all of this was
developed and tested remotely from the actual hardware.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org> Thanks-To: Gordon Pritchard <gordp@sfu.ca> Acked-by: Xiangliang Yu <yuxiangl@marvell.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vasu Dev [Fri, 28 Oct 2011 18:34:23 +0000 (11:34 -0700)]
[SCSI] libfc: improve flogi retries to avoid lport stuck
Adds more cases to do flogi retry, now also retry
on getting bad response due to either no ELS response
or flogi response payload length not large enough.
In those cases flogi was not retried and that
was leaving lport offline.
Signed-off-by: Vasu Dev <vasu.dev@intel.com> Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vasu Dev [Fri, 28 Oct 2011 18:34:17 +0000 (11:34 -0700)]
[SCSI] libfc: avoid exchanges collision during lport reset
Currently timer delay is large and is using msleep to avoid
avoid exchanges collision across lport reset, so instead
do this by initializing exches pool indexes during
reset also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com> Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vasu Dev [Fri, 28 Oct 2011 18:34:12 +0000 (11:34 -0700)]
[SCSI] libfc: fix checking FC_TYPE_BLS
Its checked after skb freed, so instead have fh_type
cached and then check FC_TYPE_BLS against cached
fh_type value.
This wrong check was causing double exch locking as
reported by Bhanu at
https://lists.open-fcoe.org/pipermail/devel/2011-October/011793.html
Signed-off-by: Vasu Dev <vasu.dev@intel.com> Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Michael Chan [Fri, 28 Oct 2011 18:34:07 +0000 (11:34 -0700)]
[SCSI] edd: Treat "XPRS" host bus type the same as "PCI"
PCI Express devices will return "XPRS" host bus type during BIOS EDD
call. "XPRS" should be treated just like "PCI" so that the proper
pci_dev symlink will be created. Scripts such as fcoe_edd.sh will
then work correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com> Reviewed-by: Matt Domsch <Matt_Domsch@dell.com> Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Andrzej Jakowski [Thu, 27 Oct 2011 22:05:42 +0000 (15:05 -0700)]
[SCSI] isci: overriding max_concurr_spinup oem parameter by max(oem, user)
Fixes bug where max_concurr_spinup oem parameter should be
overriden by max_concurr_spinup user parameter. Override should
happen only when max_concurr_spinup user parameter is specified
in command line (greater than 0). Also this fix shortens variables
representing max_conxurr_spinup for oem and user parameters.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Williams [Thu, 27 Oct 2011 22:05:37 +0000 (15:05 -0700)]
[SCSI] isci: revert bcn filtering
The initial bcn filtering implementation was validated on a kernel
baseline that predated the switch to new libata error handling. Also,
prior to that conversion we borrowed the mvsas MVS_DEV_EH approach to
prevent the unwanted extra ap->ops->phy_reset(ap) that occurred in the
ata_bus_probe() path.
After the conversion to new libata eh resets at discovery are more
frequent and get filtered prematurely by IDEV_EH. The result is that
our bcn filtering has been blocked from running and at discovery and it
appears to stall discovery completion to the point of triggering hung
task timeouts. So, revert the implementation for now. When it returns
it will go into libsas proper.
The domain rediscovery that takes place due to ->lldd_I_T_nexus_reset()
events should now be properly waited for by the ata_port_wait_eh() call
in ata_port_probe(). So the hard coded delay in the isci
->lldd_I_T_nexus_reset() and other libsas drivers should help debounce
the libsas thread from seeing temporary device removals.
Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jeff Skirvin [Thu, 27 Oct 2011 22:05:32 +0000 (15:05 -0700)]
[SCSI] isci: Fix hard reset timeout conditions.
A hard reset can timeout before or after the last phy in the
port goes away. If after, then notify the OS that the last
phy has failed.
The recovery for the failed hard reset has been removed.
This recovery code was unecessary in that the link would
recover from the failure normally by a new link reset sequence
or hotplug of the remote device.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jeff Skirvin [Thu, 27 Oct 2011 22:05:27 +0000 (15:05 -0700)]
[SCSI] isci: No need to manage the pending reset bit on pending requests.
The lldd does not need to look at or manage the pending device
reset bit in pending sas_tasks.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use the existing IREQ_TMF flag as a request type indicator.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jeff Skirvin [Thu, 27 Oct 2011 22:05:16 +0000 (15:05 -0700)]
[SCSI] isci: Fix task management for SMP, SATA and on dev remove.
libsas uses the LLDD abort task interface to handle I/O timeouts
in the SATA/STP and SMP discovery paths, so this change will terminate
STP/SMP requests. Also, if the device is gone, the lldd will prevent
libsas from further escalations in the error handler.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jeff Skirvin [Thu, 27 Oct 2011 22:05:11 +0000 (15:05 -0700)]
[SCSI] isci: No task_done callbacks in error handler paths.
libsas will cleanup pending sas_tasks after error handler
path functions are called; do not call task_done callbacks.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the case where "task" requests timeout (note that this class of
requests can also include SATA/STP soft reset FIS transmissions),
handle the case where the task was being managed by some call to
terminate the task request by completing both the tmf and the aborting
process.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jeff Skirvin [Thu, 27 Oct 2011 22:05:01 +0000 (15:05 -0700)]
[SCSI] isci: Fix tag leak in tasks and terminated requests.
Make sure terminated requests and completed task tags are freed.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jeff Skirvin [Thu, 27 Oct 2011 22:04:56 +0000 (15:04 -0700)]
[SCSI] isci: Immediately fail I/O to removed devices.
In the case where an I/O fails to start in isci_request_execute,
only allow retries if the device is not already gone.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jeff Skirvin [Thu, 27 Oct 2011 22:04:50 +0000 (15:04 -0700)]
[SCSI] isci: Lookup device references through requests in completions.
The LLDD needs to obtain a reference to the device through the request
itself and not through the domain_device, because the
domain_device.lldd_dev is set to NULL early in the lldd_dev_gone call.
This relies on the fact that the isci_remote_device object is keeping a
seperate reference count of outstanding requests. TODO: unify the
request count tracking with the isci_remote_device kref.
The failure signature of this condition looks like the following
log, where the important bits are the call to lldd_dev_gone followed
by a crash in isci_terminate_request_core:
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Wayne Boyer [Thu, 27 Oct 2011 18:58:21 +0000 (11:58 -0700)]
[SCSI] ipr: add definitions for additional adapter
Add the appropriate definition and table entry for an additional adapter.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When controller lockup condition is detected,
we should fail all outstanding commands and disable
the controller. This will enable multipath solutions
to recover gracefully.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We weren't filling in the transfer length of the
flush cache command (it transfers 4 bytes of zeroes).
Firmware didn't seem to be bothered by this, but it
should be fixed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Wed, 26 Oct 2011 21:21:12 +0000 (16:21 -0500)]
[SCSI] hpsa: fix potential array overflow in hpsa_update_scsi_devices
The currentsd[] array in hpsa_update_scsi_devices had room for
256 devices. The code was iterating over however many physical
and logical devices plus an additional number of possible external
MSA2XXX controllers, which together could potentially exceed 256.
We increased the size of the currentsd array to 1024 + 1024 + 32 + 1
elements to reflect a reasonable maximum possible number of devices
which might be encountered. We also don't just walk off the end
of the array if the array controller reports more devices than we
are prepared to handle, we just ignore the excessive devices.
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Scott Teel [Wed, 26 Oct 2011 21:21:07 +0000 (16:21 -0500)]
[SCSI] hpsa: rename HPSA_MAX_SCSI_DEVS_PER_HBA
Rename HPSA_MAX_SCSI_DEVS_PER_HBA to HPSA_MAX_DEVICES
Signed-off-by: Scott Teel <scott.teel@hp.com> Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Andrew Vasquez [Wed, 26 Oct 2011 21:20:13 +0000 (14:20 -0700)]
[SCSI] qla2xxx: Correct inadvertent clearing of RISC_INTR status.
During heavy I/O (CPU-affinity mode enabled) and CLI/Agent
interactions, the driver would report periodic mailbox command
timeout statuses. Within the CPU-affinity ISR handler, the
driver should check the 'disable-msix-handshake' flag in deciding
whether or not to clear HCCRX_CLR_RISC_INT. The mode is not
specific to a dedicated queue, instead, applies to the current
'ha' context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When SRR LS_ACC is dropped, the driver was not issuing ABTS for SRR when it
times out. Since the target received SRR, it was able to send the XFER_RDY and
the the original IO request completed successfully. In this condition ABTS was
not sent during bnx2fc_srr_compl(). Fix this by first checking for ELS timeout
and issue ABTS before checking if original IO request is complete.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] bnx2fc: Handle ABTS timeout during ulp timeout
If the IO and the corresponding ABTS are not responded by a target, cleanup the
IO and issue explicit logout when ulp timer expires while waiting for ABTS to
complete. Wait for the session to be ready before returning to the SCSI layer.
If the session is not ready let the SCSI-ml escalate the error recovery.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Petr Uzel [Fri, 21 Oct 2011 11:31:09 +0000 (13:31 +0200)]
[SCSI] st: fix race in st_scsi_execute_end
The call to complete() in st_scsi_execute_end() wakes up sleeping thread
in write_behind_check(), which frees the st_request, thus invalidating
the pointer to the associated bio structure, which is then passed to the
blk_rq_unmap_user(). Fix by storing pointer to bio structure into
temporary local variable.
This bug is present since at least linux-2.6.32.
CC: stable@kernel.org Signed-off-by: Petr Uzel <petr.uzel@suse.cz> Reported-by: Juergen Groß <juergen.gross@ts.fujitsu.com> Reviewed-by: Jan Kara <jack@suse.cz> Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] Make scsi_free_queue() kill pending SCSI commands
Make sure that SCSI device removal via scsi_remove_host() does finish
all pending SCSI commands. Currently that's not the case and hence
removal of a SCSI host during I/O can cause a deadlock. See also
"blkdev_issue_discard() hangs forever if underlying storage device is
removed" (http://bugzilla.kernel.org/show_bug.cgi?id=40472). See also
http://lkml.org/lkml/2011/8/27/6.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Cc: <stable@kernel.org> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] mpt2sas: Fix for Panic when inactive volume is tried deleting
The driver was setting the action to MPI2_CONFIG_ACTION_PAGE_READ_CURRENT,
which only returns active volumes. In order to get info on inactive volumes,
the driver needs to change the action to
MPI2_RAID_PGAD_FORM_GET_NEXT_CONFIGNUM, and traverse each config till the
iocstatus is MPI2_IOCSTATUS_CONFIG_INVALID_PAGE returned.
Added a change in the driver to remove the instance of
sas_device object when the driver returns "1" from the slave_configure callback.
Also fixed code to report the hot spares to the operating system with a /dev/sg
assigned.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com> Cc: stable@kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] mpt2sas: Fix for issue Port Reset taking long time(around 5 mins) to complete while issued during creating a volume
This is due to the slave_configuration routine is getting called when
host reset is active, and config page reads are failing, and driver
attempts to added device with stale config data.
To fix the issue, added error checking in slave_configure to check
for configuration pages failing, and return "1" so the device is
not configured. The config pages are failing if raid volume is
configured while issuing a host reset, thus driver is reading stale
data and proceeding to attempt to add. The fix is to return error
so the volume is not configured.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] mpt2sas: Fix for deadlock between hot plug worker threads and host reset context
This is due to driver reporting a device missing to the OS then the OS sending
a SYNC_CACHE request to driver while the IO queues are locked due to host reset.
To fix the issue, the driver will be waking up the port enable context
immediately when the driver receives the reply message, instead of waiting
on the hot plug worker threads.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] mpt2sas: Fix for dead lock occurring between host_lock and sas_device_lock
Fix for dead lock occurring between host_lock and sas_device_lock.
The deadlock is between two spin locks, between the shost->host_lock
and driver ioc->sas_device_lock.
The fix is to rearrange the code in the FW/Driver device removal
handshake so the ioc->sas_device_lock is not occurring when the
shost->host_lock is taken.
[jejb: zero initialise sas_address to fix spurious compiler warning] Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] mpt2sas: Fix drives not getting properly deleted if sas cable is removed while host reset is active
The fix is in the driver-firmware handshake device removal code. We
need to read the controller ioc_state to see if controller is OPERATIONAL
prior to sending target reset and OP_REMOVE. Previously it was checking
the flag ioc->shost_recovery flag, which is always set when host reset is
active, thus preventing drives from getting properly deleted.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[SCSI] mpt2sas: Fix for system hang when discovery in progress
Fix for issue : While discovery is in progress, hot unplug and hot plug of
enclosure connected to the controller card is causing system to hang.
When a device is in the process of being detected at driver load time then
if it is removed, the device that is no longer present will not be added
to the list. So the code in _scsih_probe_sas() is rearranged as such so
the devices that failed to be detected are not added to the list.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com> Cc: stable@kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
(1)Asynchronous SCSI scanning: This will allow the drivers to scan
for devices in parallel while other device drivers are loading at
the same time. This will improve the amount of time it takes for the
OS to load.
(2) Reporting Devices while port enable is active: This feature will
allow devices to be reported to OS immediately while port enable is
active. The previous implementation waits for port enable to complete,
and then report devices. This feature is only enabled on IT firmware
configurations when there are no boot device configured in BIOS Configuration
Utility, else the driver will wait till port enable completes reporting
devices. For IR firmware, this feature is turned off. This feature is to
address large SAS topologies (>100 drives) when the boot OS is using onboard
SATA device, in other words, the boot devices is not
connected to our controller.
(3) Scanning for devices after diagnostic reset completes: A new routine
_scsih_scan_start is added. This will scan the expander pages, IR pages,
and sas device pages, then reporting new devices to SCSI Mid layer. It
seems the driver is not supporting adding devices while diagnostic reset
is active. Apparently this is due to the sanity checks on
ioc->shost_recovery flag throughout the context of kernel work thread FIFO,
and the mpt2sas_fw_work.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1)Added ProxyVF_ID field to Configuration Request message.
2)Added IO Unit Page 8, IO Unit Page 9,and IO Unit Page 10.
3)Added SASNotifyPrimitiveMasks field to IOC Page 7.
4)Added SAS NOTIFY Primitive event.
5)Added Temperature Threshold Event.
6)Added Host Message Event.
7)Added Send Host Message request and reply.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus Torvalds [Fri, 28 Oct 2011 23:42:18 +0000 (16:42 -0700)]
Merge branch 'for-linus' of git://ceph.newdream.net/git/ceph-client
* 'for-linus' of git://ceph.newdream.net/git/ceph-client:
libceph: fix double-free of page vector
ceph: fix 32-bit ino numbers
libceph: force resend of osd requests if we skip an osdmap
ceph: use kernel DNS resolver
ceph: fix ceph_monc_init memory leak
ceph: let the set_layout ioctl set single traits
Revert "ceph: don't truncate dirty pages in invalidate work thread"
ceph: replace leading spaces with tabs
libceph: warn on msg allocation failures
libceph: don't complain on msgpool alloc failures
libceph: always preallocate mon connection
libceph: create messenger with client
ceph: document ioctls
ceph: implement (optional) max read size
ceph: rename rsize -> rasize
ceph: make readpages fully async
Linus Torvalds [Fri, 28 Oct 2011 21:25:01 +0000 (14:25 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
Linus Torvalds [Fri, 28 Oct 2011 21:20:44 +0000 (14:20 -0700)]
Merge branch 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci
* 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Clean-up MPS debug output
pci: Clamp pcie_set_readrq() when using "performance" settings
PCI: enable MPS "performance" setting to properly handle bridge MPS
PCI: Workaround for Intel MPS errata
PCI: Add support for PASID capability
PCI: Add implementation for PRI capability
PCI: Export ATS functions to modules
PCI: Move ATS implementation into own file
PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()
PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove
PCI / PM: Extend PME polling to all PCI devices
PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823
PCI: Make pci_setup_bridge() non-static for use by arch code
x86: constify PCI raw ops structures
PCI: Add quirk for known incorrect MPSS
PCI: Add Solarflare vendor ID and SFC4000 device IDs
Linus Torvalds [Fri, 28 Oct 2011 21:16:11 +0000 (14:16 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits)
mmc: fix compile error when CONFIG_BLOCK is not enabled
mmc: core: Cleanup eMMC4.5 conditionals
mmc: omap_hsmmc: if multiblock reads are broken, disable them
mmc: core: add workaround for controllers with broken multiblock reads
mmc: core: Prevent too long response times for suspend
mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
mmc: core: support HPI send command
mmc: core: Add cache control for eMMC4.5 device
mmc: core: Modify the timeout value for writing power class
mmc: core: new discard feature support at eMMC v4.5
mmc: core: mmc sanitize feature support for v4.5
mmc: dw_mmc: modify DATA register offset
mmc: sdhci-pci: add flag for devices that can support runtime PM
mmc: omap_hsmmc: ensure pbias configuration is always done
mmc: core: Add Power Off Notify Feature eMMC 4.5
mmc: sdhci-s3c: fix potential NULL dereference
mmc: replace printk with appropriate display macro
mmc: core: Add default timeout value for CMD6
mmc: sdhci-pci: add runtime pm support
...
Linus Torvalds [Fri, 28 Oct 2011 19:02:27 +0000 (12:02 -0700)]
Merge branch 'devel-stable' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'devel-stable' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: (178 commits)
ARM: 7139/1: fix compilation with CONFIG_ARM_ATAG_DTB_COMPAT and large TEXT_OFFSET
ARM: gic, local timers: use the request_percpu_irq() interface
ARM: gic: consolidate PPI handling
ARM: switch from NO_MACH_MEMORY_H to NEED_MACH_MEMORY_H
ARM: mach-s5p64x0: remove mach/memory.h
ARM: mach-s3c64xx: remove mach/memory.h
ARM: plat-mxc: remove mach/memory.h
ARM: mach-prima2: remove mach/memory.h
ARM: mach-zynq: remove mach/memory.h
ARM: mach-bcmring: remove mach/memory.h
ARM: mach-davinci: remove mach/memory.h
ARM: mach-pxa: remove mach/memory.h
ARM: mach-ixp4xx: remove mach/memory.h
ARM: mach-h720x: remove mach/memory.h
ARM: mach-vt8500: remove mach/memory.h
ARM: mach-s5pc100: remove mach/memory.h
ARM: mach-tegra: remove mach/memory.h
ARM: plat-tcc: remove mach/memory.h
ARM: mach-mmp: remove mach/memory.h
ARM: mach-cns3xxx: remove mach/memory.h
...
Fix up mostly pretty trivial conflicts in:
- arch/arm/Kconfig
- arch/arm/include/asm/localtimer.h
- arch/arm/kernel/Makefile
- arch/arm/mach-shmobile/board-ap4evb.c
- arch/arm/mach-u300/core.c
- arch/arm/mm/dma-mapping.c
- arch/arm/mm/proc-v7.S
- arch/arm/plat-omap/Kconfig
largely due to some CONFIG option renaming (ie CONFIG_PM_SLEEP ->
CONFIG_ARM_CPU_SUSPEND for the arm-specific suspend code etc) and
addition of NEED_MACH_MEMORY_H next to HAVE_IDE.
Linus Torvalds [Fri, 28 Oct 2011 17:49:34 +0000 (10:49 -0700)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue: (21 commits)
leases: fix write-open/read-lease race
nfs: drop unnecessary locking in llseek
ext4: replace cut'n'pasted llseek code with generic_file_llseek_size
vfs: add generic_file_llseek_size
vfs: do (nearly) lockless generic_file_llseek
direct-io: merge direct_io_walker into __blockdev_direct_IO
direct-io: inline the complete submission path
direct-io: separate map_bh from dio
direct-io: use a slab cache for struct dio
direct-io: rearrange fields in dio/dio_submit to avoid holes
direct-io: fix a wrong comment
direct-io: separate fields only used in the submission path from struct dio
vfs: fix spinning prevention in prune_icache_sb
vfs: add a comment to inode_permission()
vfs: pass all mask flags check_acl and posix_acl_permission
vfs: add hex format for MAY_* flag values
vfs: indicate that the permission functions take all the MAY_* flags
compat: sync compat_stats with statfs.
vfs: add "device" tag to /proc/self/mountstats
cleanup: vfs: small comment fix for block_invalidatepage
...
Fix up trivial conflict in fs/gfs2/file.c (llseek changes)
Linus Torvalds [Fri, 28 Oct 2011 17:44:50 +0000 (10:44 -0700)]
Merge http://sucs.org/~rohan/git/gfs2-3.0-nmw
* http://sucs.org/~rohan/git/gfs2-3.0-nmw: (24 commits)
GFS2: Move readahead of metadata during deallocation into its own function
GFS2: Remove two unused variables
GFS2: Misc fixes
GFS2: rewrite fallocate code to write blocks directly
GFS2: speed up delete/unlink performance for large files
GFS2: Fix off-by-one in gfs2_blk2rgrpd
GFS2: Clean up ->page_mkwrite
GFS2: Correctly set goal block after allocation
GFS2: Fix AIL flush issue during fsync
GFS2: Use cached rgrp in gfs2_rlist_add()
GFS2: Call do_strip() directly from recursive_scan()
GFS2: Remove obsolete assert
GFS2: Cache the most recently used resource group in the inode
GFS2: Make resource groups "append only" during life of fs
GFS2: Use rbtree for resource groups and clean up bitmap buffer ref count scheme
GFS2: Fix lseek after SEEK_DATA, SEEK_HOLE have been added
GFS2: Clean up gfs2_create
GFS2: Use ->dirty_inode()
GFS2: Fix bug trap and journaled data fsync
GFS2: Fix inode allocation error path
...
Linus Torvalds [Fri, 28 Oct 2011 17:43:32 +0000 (10:43 -0700)]
Merge branch '3.2-without-smb2' of git://git.samba.org/sfrench/cifs-2.6
* '3.2-without-smb2' of git://git.samba.org/sfrench/cifs-2.6: (52 commits)
Fix build break when freezer not configured
Add definition for share encryption
CIFS: Make cifs_push_locks send as many locks at once as possible
CIFS: Send as many mandatory unlock ranges at once as possible
CIFS: Implement caching mechanism for posix brlocks
CIFS: Implement caching mechanism for mandatory brlocks
CIFS: Fix DFS handling in cifs_get_file_info
CIFS: Fix error handling in cifs_readv_complete
[CIFS] Fixup trivial checkpatch warning
[CIFS] Show nostrictsync and noperm mount options in /proc/mounts
cifs, freezer: add wait_event_freezekillable and have cifs use it
cifs: allow cifs_max_pending to be readable under /sys/module/cifs/parameters
cifs: tune bdi.ra_pages in accordance with the rsize
cifs: allow for larger rsize= options and change defaults
cifs: convert cifs_readpages to use async reads
cifs: add cifs_async_readv
cifs: fix protocol definition for READ_RSP
cifs: add a callback function to receive the rest of the frame
cifs: break out 3rd receive phase into separate function
cifs: find mid earlier in receive codepath
...
Linus Torvalds [Fri, 28 Oct 2011 17:31:42 +0000 (10:31 -0700)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (69 commits)
xfs: add AIL pushing tracepoints
xfs: put in missed fix for merge problem
xfs: do not flush data workqueues in xfs_flush_buftarg
xfs: remove XFS_bflush
xfs: remove xfs_buf_target_name
xfs: use xfs_ioerror_alert in xfs_buf_iodone_callbacks
xfs: clean up xfs_ioerror_alert
xfs: clean up buffer allocation
xfs: remove buffers from the delwri list in xfs_buf_stale
xfs: remove XFS_BUF_STALE and XFS_BUF_SUPER_STALE
xfs: remove XFS_BUF_SET_VTYPE and XFS_BUF_SET_VTYPE_REF
xfs: remove XFS_BUF_FINISH_IOWAIT
xfs: remove xfs_get_buftarg_list
xfs: fix buffer flushing during unmount
xfs: optimize fsync on directories
xfs: reduce the number of log forces from tail pushing
xfs: Don't allocate new buffers on every call to _xfs_buf_find
xfs: simplify xfs_trans_ijoin* again
xfs: unlock the inode before log force in xfs_change_file_space
xfs: unlock the inode before log force in xfs_fs_nfs_commit_metadata
...
Add a generic_file_llseek variant to the VFS that allows passing in
the maximum file size of the file system, instead of always
using maxbytes from the superblock.
This can be used to eliminate some cut'n'paste seek code in ext4.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
The i_mutex lock use of generic _file_llseek hurts. Independent processes
accessing the same file synchronize over a single lock, even though
they have no need for synchronization at all.
Under high utilization this can cause llseek to scale very poorly on larger
systems.
This patch does some rethinking of the llseek locking model:
First the 64bit f_pos is not necessarily atomic without locks
on 32bit systems. This can already cause races with read() today.
This was discussed on linux-kernel in the past and deemed acceptable.
The patch does not change that.
Let's look at the different seek variants:
SEEK_SET: Doesn't really need any locking.
If there's a race one writer wins, the other loses.
For 32bit the non atomic update races against read()
stay the same. Without a lock they can also happen
against write() now. The read() race was deemed
acceptable in past discussions, and I think if it's
ok for read it's ok for write too.
=> Don't need a lock.
SEEK_END: This behaves like SEEK_SET plus it reads
the maximum size too. Reading the maximum size would have the
32bit atomic problem. But luckily we already have a way to read
the maximum size without locking (i_size_read), so we
can just use that instead.
Without i_mutex there is no synchronization with write() anymore,
however since the write() update is atomic on 64bit it just behaves
like another racy SEEK_SET. On non atomic 32bit it's the same
as SEEK_SET.
=> Don't need a lock, but need to use i_size_read()
SEEK_CUR: This has a read-modify-write race window
on the same file. One could argue that any application
doing unsynchronized seeks on the same file is already broken.
But for the sake of not adding a regression here I'm
using the file->f_lock to synchronize this. Using this
lock is much better than the inode mutex because it doesn't
synchronize between processes.
=> So still need a lock, but can use a f_lock.
This patch implements this new scheme in generic_file_llseek.
I dropped generic_file_llseek_unlocked and changed all callers.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Andi Kleen [Tue, 2 Aug 2011 04:38:08 +0000 (21:38 -0700)]
direct-io: inline the complete submission path
Add inlines to all the submission path functions. While this increases
code size it also gives gcc a lot of optimization opportunities
in this critical hotpath.
In particular -- together with some other changes -- this
allows gcc to get rid of the unnecessary clearing of
sdio at the beginning and optimize the messy parameter passing.
Any non inlining of a function which takes a sdio parameter
would break this optimization because they cannot be done if the
address of a structure is taken.
Note that benefits are only seen with CONFIG_OPTIMIZE_INLINING
and CONFIG_CC_OPTIMIZE_FOR_SIZE both set to off.
This gives about 2.2% improvement on a large database benchmark
with a high IOPS rate.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Andi Kleen [Tue, 2 Aug 2011 04:38:07 +0000 (21:38 -0700)]
direct-io: separate map_bh from dio
Only a single b_private field in the map_bh buffer head is needed after
the submission path. Move map_bh separately to avoid storing
this information in the long term slab.
This avoids the weird 104 byte hole in struct dio_submit which also needed
to be memseted early.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Andi Kleen [Tue, 2 Aug 2011 04:38:03 +0000 (21:38 -0700)]
direct-io: separate fields only used in the submission path from struct dio
This large, but largely mechanic, patch moves all fields in struct dio
that are only used in the submission path into a separate on stack
data structure. This has the advantage that the memory is very likely
cache hot, which is not guaranteed for memory fresh out of kmalloc.
This also gives gcc more optimization potential because it can easier
determine that there are no external aliases for these variables.
The sdio initialization is a initialization now instead of memset.
This allows gcc to break sdio into individual fields and optimize
away unnecessary zeroing (after all the functions are inlined)
Signed-off-by: Andi Kleen <ak@linux.intel.com> Acked-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
We need to move the inode to the end of the list to actually make the
spinning prevention explained in the comment above it work. With a
plain list_move it will simply stay in place as we're always reclaiming
from the head of the list.
Acked-by: J. Bruce Fields <bfields@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andreas Gruenbacher <agruen@kernel.org> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
vfs: pass all mask flags check_acl and posix_acl_permission
Acked-by: J. Bruce Fields <bfields@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andreas Gruenbacher <agruen@kernel.org> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
We are going to add more flags and having them in hex format
make it simpler
Acked-by: J. Bruce Fields <bfields@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
vfs: indicate that the permission functions take all the MAY_* flags
Acked-by: J. Bruce Fields <bfields@redhat.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Andreas Gruenbacher <agruen@kernel.org> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
This was found by inspection while tracking a similar
bug in compat_statfs64, that has been fixed in mainline
since decemeber.
- This fixes a bug where not all of the f_spare fields
were cleared on mips and s390.
- Add the f_flags field to struct compat_statfs
- Copy f_flags to userspace in case someone cares.
- Use __clear_user to copy the f_spare field to userspace
to ensure that all of the elements of f_spare are cleared.
On some architectures f_spare is has 5 ints and on some
architectures f_spare only has 4 ints. Which makes
the previous technique of clearing each int individually
broken.
I don't expect anyone actually uses the old statfs system
call anymore but if they do let them benefit from having
the compat and the native version working the same.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Linus Torvalds [Fri, 28 Oct 2011 12:54:23 +0000 (05:54 -0700)]
Merge branch 'drm-core-next' of git://people.freedesktop.org/~airlied/linux
* 'drm-core-next' of git://people.freedesktop.org/~airlied/linux: (290 commits)
Revert "drm/ttm: add a way to bo_wait for either the last read or last write"
Revert "drm/radeon/kms: add a new gem_wait ioctl with read/write flags"
vmwgfx: Don't pass unused arguments to do_dirty functions
vmwgfx: Emulate depth 32 framebuffers
drm/radeon: Lower the severity of the radeon lockup messages.
drm/i915/dp: Fix eDP on PCH DP on CPT/PPT
drm/i915/dp: Introduce is_cpu_edp()
drm/i915: use correct SPD type value
drm/i915: fix ILK+ infoframe support
drm/i915: add DP test request handling
drm/i915: read full receiver capability field during DP hot plug
drm/i915/dp: Remove eDP special cases from bandwidth checks
drm/i915/dp: Fix the math in intel_dp_link_required
drm/i915/panel: Always record the backlight level again (but cleverly)
i915: Move i915_read/write out of line
drm/i915: remove transcoder PLL mashing from mode_set per specs
drm/i915: if transcoder disable fails, say which
drm/i915: set watermarks for third pipe on IVB
drm/i915: export a CPT mode set verification function
drm/i915: fix transcoder PLL select masking
...
Linus Torvalds [Fri, 28 Oct 2011 12:46:02 +0000 (05:46 -0700)]
Merge branch 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, doc: Remove int 0xcc from entry_64.S documentation
x86, vsyscall: Add missing <asm/fixmap.h> to arch/x86/mm/fault.c
Fix up trivial conflicts in arch/x86/mm/fault.c (asm/fixmap.h vs
asm/vsyscall.h: both work, which to use? Whatever..)
Linus Torvalds [Fri, 28 Oct 2011 12:43:29 +0000 (05:43 -0700)]
Merge branch 'x86-spinlocks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-spinlocks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, ticketlock: remove obsolete comment
x86, cmpxchg: Use __compiletime_error() to make usage messages a bit nicer
x86, ticketlock: Make __ticket_spin_trylock common
x86, ticketlock: Convert __ticket_spin_lock to use xadd()
x86, ticketlock: Convert spin loop to C
x86, ticketlock: Clean up types and accessors
x86: Use xadd helper more widely
x86: Add xadd helper macro
x86, cmpxchg: Unify cmpxchg into cmpxchg.h
x86, cmpxchg: Move 64-bit set64_bit() to match 32-bit
x86, cmpxchg: Move 32-bit __cmpxchg_wrong_size to match 64 bit.
x86, cmpxchg: <linux/alternative.h> has LOCK_PREFIX
Linus Torvalds [Fri, 28 Oct 2011 12:29:07 +0000 (05:29 -0700)]
Merge branch 'x86-rdrand-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-rdrand-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, random: Verify RDRAND functionality and allow it to be disabled
x86, random: Architectural inlines to get random integers with RDRAND
random: Add support for architectural random hooks
Fix up trivial conflicts in drivers/char/random.c: the architectural
random hooks touched "get_random_int()" that was simplified to use MD5
and not do the keyptr thing any more (see commit 6e5714eaf77d: "net:
Compute protocol sequence numbers and fragment IDs using MD5").
Linus Torvalds [Fri, 28 Oct 2011 12:14:48 +0000 (05:14 -0700)]
Merge branch 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Add microcode revision to /proc/cpuinfo
x86, microcode: Correct microcode revision format
coretemp: Get microcode revision from cpu_data
x86, intel: Use c->microcode for Atom errata check
x86, intel: Output microcode revision in /proc/cpuinfo
x86, microcode: Don't request microcode from userspace unnecessarily
Fix up trivial conflicts in arch/x86/kernel/cpu/amd.c (conflict between
moving AMD BSP code to cpu_dev helper function and adding AMD microcode
revision to /proc/cpuinfo code)
Linus Torvalds [Fri, 28 Oct 2011 12:03:12 +0000 (05:03 -0700)]
Merge branch 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, amd: Include linux/elf.h since we use stuff from asm/elf.h
x86: cache_info: Update calculation of AMD L3 cache indices
x86: cache_info: Kill the atomic allocation in amd_init_l3_cache()
x86: cache_info: Kill the moronic shadow struct
x86: cache_info: Remove bogus free of amd_l3_cache data
x86, amd: Include elf.h explicitly, prepare the code for the module.h split
x86-32, amd: Move va_align definition to unbreak 32-bit build
x86, amd: Move BSP code to cpu_dev helper
x86: Add a BSP cpu_dev helper
x86, amd: Avoid cache aliasing penalties on AMD family 15h
Bryan Schumaker [Fri, 7 Oct 2011 17:41:15 +0000 (13:41 -0400)]
vfs: add "device" tag to /proc/self/mountstats
nfsiostat was failing to find mounted filesystems on kernels after
2.6.38 because of changes to show_vfsstat() by commit c7f404b40a3665d9f4e9a927cc5c1ee0479ed8f9. This patch adds back the
"device" tag before the nfs server entry so scripts can parse the
mountstats file correctly.
Jeff Layton [Thu, 27 Oct 2011 21:53:08 +0000 (23:53 +0200)]
vfs: iov_iter: have iov_iter_advance decrement nr_segs appropriately
Currently, when you call iov_iter_advance, then the pointer to the iovec
array can be incremented, but it does not decrement the nr_segs value in
the iov_iter struct. The result is a iov_iter struct with a nr_segs
value that goes beyond the end of the array.
While I'm not aware of anything that's specifically broken by this, it
seems odd and a bit dangerous not to decrement that value. If someone
were to trust the nr_segs value to be correct, then they could end up
walking off the end of the array.
Changing this might also provide some micro-optimization when dealing
with the last iovec in an array. Many of the other routines that deal
with iov_iter have optimized codepaths when nr_segs == 1.
Cc: Nick Piggin <npiggin@suse.de> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
Steve French [Tue, 25 Oct 2011 01:46:50 +0000 (20:46 -0500)]
Add definition for share encryption
Samba supports a setfs info level to negotiate encrypted
shares. This patch adds the defines so we recognize
this info level. Later patches will add the enablement
for it.
Acked-by: Jeremy Allison <jra@samba.org> Signed-off-by: Steve French <smfrench@gmail.com>
Jon Mason [Fri, 14 Oct 2011 19:56:16 +0000 (14:56 -0500)]
PCI: Clean-up MPS debug output
Clean-up MPS debug output to make it a single line and aligned, thus
making it more readable for a large number of buses and devices in a
single system.
Suggested by Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jon Mason <mason@myri.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci: Clamp pcie_set_readrq() when using "performance" settings
When configuring the PCIe settings for "performance", we allow parents
to have a larger Max Payload Size than children and rely on children
Max Read Request Size to not be larger than their own MPS to avoid
having the host bridge generate responses they can't cope with.
However, various drivers in Linux call pci_set_readrq() with arbitrary
values, assuming this to be a simple performance tweak. This breaks
under our "performance" configuration.
Fix that by making sure the value programmed by pcie_set_readrq() is
never larger than the configured MPS for that device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jon Mason <mason@myri.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jon Mason [Fri, 14 Oct 2011 19:56:14 +0000 (14:56 -0500)]
PCI: enable MPS "performance" setting to properly handle bridge MPS
Rework the "performance" MPS option to configure the device MPS with the
smaller of the device MPSS or the bridge MPS (which is assumed to be
properly configured at this point to the largest allowable MPS based on
its parent bus).
Also, rework the MRRS setting to report an inability to set the MRRS to
a valid setting.
Signed-off-by: Jon Mason <mason@myri.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Jon Mason [Fri, 14 Oct 2011 19:56:13 +0000 (14:56 -0500)]
PCI: Workaround for Intel MPS errata
Intel 5000 and 5100 series memory controllers have a known issue if read
completion coalescing is enabled and the PCI-E Maximum Payload Size is
set to 256B. To work around this issue, disable read completion
coalescing in the memory controller and root complexes. Unfortunately,
it must always be disabled, even if no 256B MPS devices are present, due
to the possibility of one being hotplugged.
Links to erratas:
http://www.intel.com/content/dam/doc/specification-update/5000-chipset-memory-controller-hub-specification-update.pdf
http://www.intel.com/content/dam/doc/specification-update/5100-memory-controller-hub-chipset-specification-update.pdf
Thanks to Jesse Brandeburg and Ben Hutchings for providing insight into
the problem.
Tested-and-Reported-by: Avi Kivity <avi@redhat.com> Signed-off-by: Jon Mason <mason@myri.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Takashi Iwai [Fri, 14 Oct 2011 13:26:20 +0000 (15:26 +0200)]
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
It seems that Conexant CX20549 chip handle only a single input-amp even
though the audio-input widget has multiple sources. This has been never
clear, and I implemented in the current way based on the debug information
I got at the early time -- the device reacts individual input-amp values
for different sources. This is true for another Conexant codec, but it's
not applied to CX20549 actually.
This patch changes the auto-parser code to handle a single input-amp
per audio-in widget for CX20549. After applying this, you'll see only a
single "Capture" volume control instead of separate "Mic" or "Line"
captures when the device is set up to use a single ADC.
We haven't tested 20551 and 20561 codecs yet. If these show the similar
behavior like 20549, they need to set spec->single_adc_amp=1, too.
Takashi Iwai [Fri, 14 Oct 2011 13:22:34 +0000 (15:22 +0200)]
ALSA: hda - Keep EAPD turned on for old Conexant chips
In the old Conexant chips (5045, 5047, 5051 and 5066), a single EAPD
may handle both headphone and speaker outputs while it's assigned only
to one of them. Turning off dynamically leads to the unexpected silent
output in such a configuration with the auto-mute function.
Since it's difficult to know how the EAPD is handled in the actual h/w
implementation, better to keep EAPD on while running for such codecs.
Takashi Iwai [Thu, 27 Oct 2011 14:33:27 +0000 (16:33 +0200)]
ALSA: hda/realtek - Fix missing volume controls with ALC260
ALC260 has multiple mixer widgets connected to the shared DAC, but the
driver currently doesn't check this possibility and ignores when the DAC
is shared with others. This resulted in the silent output from some
routes because of lack of the amp setup.
This patch adds the workaround for it by checking the route even with the
shared DAC, but also checking the conflict with the existing control for
the very same widget NID.
Namjae Jeon [Wed, 12 Oct 2011 15:43:14 +0000 (00:43 +0900)]
mmc: fix compile error when CONFIG_BLOCK is not enabled
'DISK_NAME_LEN' is undeclared when CONFIG_BLOCK is disabled; its use was
introduced via genhd.h by the general purpose partition patch.
To fix, we just add our own MAX_MMC_PART_NAME_LEN macro instead of using
DISK_NAME_LEN.
Reported-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Namjae Jeon <linkinjeon@gmail.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Acked-by: Andrei Warkentin <andreiw@vmware.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Seungwon Jeon [Tue, 25 Oct 2011 00:43:12 +0000 (09:43 +0900)]
mmc: core: Cleanup eMMC4.5 conditionals
Code cleanup, putting all eMMC 4.5 detection cases together.
This patch removes one if-statement and assembles all. And it also
removes variable initialization below else-statement -- all members
of card structure are already set to zero at card-init.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Paul Walmsley [Thu, 6 Oct 2011 20:50:35 +0000 (14:50 -0600)]
mmc: omap_hsmmc: if multiblock reads are broken, disable them
When device data indicates that multiple block reads are not supported
on a given HSMMC controller instance, log a message to the console, and
pass the appropriate MMC capability flag to the MMC core.
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Dave Hylands <dhylands@gmail.com> Tested-by: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
Paul Walmsley [Thu, 6 Oct 2011 20:50:33 +0000 (14:50 -0600)]
mmc: core: add workaround for controllers with broken multiblock reads
Due to hardware bugs, some MMC host controllers don't support
multiple-block reads[1]. To resolve, add a new MMC capability flag,
MMC_CAP2_NO_MULTI_READ, which can be set by affected host controller
drivers. When this capability is set, all reads will be issued one
sector at a time.
1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf
Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Dave Hylands <dhylands@gmail.com> Tested-by: Steve Sakoman <sakoman@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
projects / mv-sheeva.git / log