ALSA: hda - Suppress CORBRP clear on Nvidia controller chips
The recent commit (ca460f86521) changed the CORB RP reset procedure to
follow the specification with a couple of sanity checks.
Unfortunately, Nvidia controller chips seem not following this way,
and spew the warning messages like:
snd_hda_intel 0000:00:10.1: CORB reset timeout#1, CORBRP = 0
This patch adds the workaround for such chips. It just skips the new
reset procedure for the known broken chips.
As the i915.enable_ppgtt is read-only it cannot be changed after the
module is loaded and so we can perform an early sanitization of the
values.
v2:
- Add comment and pimp commit message (Chris)
- Use the param consistently (Jani)
v3:
- Fix init sequence on pre-gen6 by moving the sanitize_ppgtt call to
gtt_init. Fixes boot hangs on pre-gen6.
- Add a debug output for the sanitize ppgtt mode.
References: https://lkml.org/lkml/2014/4/17/599
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77916 Cc: Alessandro Suardi <alessandro.suardi@gmail.com> Cc: Ben Widawsky <ben@bwidawsk.net> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Grant Likely [Tue, 29 Apr 2014 11:05:22 +0000 (12:05 +0100)]
drivercore: deferral race condition fix
When the kernel is built with CONFIG_PREEMPT it is possible to reach a state
when all modules loaded but some driver still stuck in the deferred list
and there is a need for external event to kick the deferred queue to probe
these drivers.
The issue has been observed on embedded systems with CONFIG_PREEMPT enabled,
audio support built as modules and using nfsroot for root filesystem.
The following log fragment shows such sequence when all audio modules
were loaded but the sound card is not present since the machine driver has
failed to probe due to missing dependency during it's probe.
The board is am335x-evmsk (McASP<->tlv320aic3106 codec) with davinci-evm
machine driver:
In the log the machine driver enters it's probe at 12.719969 (this point it
has been removed from the deferred lists). McASP driver already executing
it's probing (since 12.615118).
The machine driver tries to construct the sound card (12.950839) but did
not found one of the components so it fails. After this McASP driver
registers all the ASoC components (the machine driver still in it's probe
function after it failed to construct the card) and the deferred work is
prepared at 13.099026 (note that this time the machine driver is not in the
lists so it is not going to be handled when the work is executing).
Lastly the machine driver exit from it's probe and the core places it to
the deferred list but there will be no other driver going to load and the
deferred queue is not going to be kicked again - till we have external event
like connecting USB stick, etc.
The proposed solution is to try the deferred queue once more when the last
driver is asking for deferring and we had drivers loaded while this last
driver was probing.
This way we can avoid drivers stuck in the deferred queue.
Signed-off-by: Grant Likely <grant.likely@linaro.org> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Mark Brown <broonie@kernel.org> Cc: Stable <stable@vger.kernel.org> # v3.4+
Merge tag 'trace-fixes-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace bugfix from Steven Rostedt:
"Takao Indoh reported that he was able to cause a ftrace bug while
loading a module and enabling function tracing at the same time.
He uncovered a race where the module when loaded will convert the
calls to mcount into nops, and expects the module's text to be RW.
But when function tracing is enabled, it will convert all kernel text
(core and module) from RO to RW to convert the nops to calls to ftrace
to record the function. After the convertion, it will convert all the
text back from RW to RO.
The issue is, it will also convert the module's text that is loading.
If it converts it to RO before ftrace does its conversion, it will
cause ftrace to fail and require a reboot to fix it again.
This patch moves the ftrace module update that converts calls to
mcount into nops to be done when the module state is still
MODULE_STATE_UNFORMED. This will ignore the module when the text is
being converted from RW back to RO"
* tag 'trace-fixes-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/module: Hardcode ftrace_module_init() call into load_module()
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree bug fixes from Grant Likely:
"These are some important bug fixes that need to get into v3.15.
This branch contains a pair of important bug fixes for the DT code:
- Fix some incorrect binding property names before they enter common
usage
- Fix bug where some platform devices will be unable to get their
interrupt number when they depend on an interrupt controller that
is not available at device creation time. This is a problem
causing mainline to fail on a number of ARM platforms"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of/irq: do irq resolution in platform_get_irq
of: selftest: add deferred probe interrupt test
dt: Fix binding typos in clock-names and interrupt-names
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"Here is a bunch of post-merge window fixes that have been accumulating
in patchwork while I was on vacation or buried under other stuff last
week.
We have the now usual batch of LE fixes from Anton (sadly some new
stuff that went into this merge window had endian issues, we'll try to
make sure we do better next time)
Some fixes and cleanups to the new 24x7 performance monitoring stuff
(mostly typos and cleaning up printk's)
A series of fixes for an issue with our runlatch bit, which wasn't set
properly for offlined threads/cores and under KVM, causing potentially
some counters to misbehave along with possible power management
issues.
A fix for kexec nasty race where the new kernel wouldn't "see" the
secondary processors having reached back into firmware in time.
And finally a few other misc (and pretty simple) bug fixes"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (33 commits)
powerpc/4xx: Fix section mismatch in ppc4xx_pci.c
ppc/kvm: Clear the runlatch bit of a vcpu before napping
ppc/kvm: Set the runlatch bit of a CPU just before starting guest
ppc/powernv: Set the runlatch bits correctly for offline cpus
powerpc/pseries: Protect remove_memory() with device hotplug lock
powerpc: Fix error return in rtas_flash module init
powerpc: Bump BOOT_COMMAND_LINE_SIZE to 2048
powerpc: Bump COMMAND_LINE_SIZE to 2048
powerpc: Rename duplicate COMMAND_LINE_SIZE define
powerpc/perf/hv-24x7: Catalog version number is be64, not be32
powerpc/perf/hv-24x7: Remove [static 4096], sparse chokes on it
powerpc/perf/hv-24x7: Use (unsigned long) not (u32) values when calling plpar_hcall_norets()
powerpc/perf/hv-gpci: Make device attr static
powerpc/perf/hv_gpci: Probe failures use pr_debug(), and padding reduced
powerpc/perf/hv_24x7: Probe errors changed to pr_debug(), padding fixed
powerpc/mm: Fix tlbie to add AVAL fields for 64K pages
powerpc/powernv: Fix little endian issues in OPAL dump code
powerpc/powernv: Create OPAL sglist helper functions and fix endian issues
powerpc/powernv: Fix little endian issues in OPAL error log code
powerpc/powernv: Fix little endian issues with opal_do_notifier calls
...
mm: don't pointlessly use BUG_ON() for sanity check
BUG_ON() is a big hammer, and should be used _only_ if there is some
major corruption that you cannot possibly recover from, making it
imperative that the current process (and possibly the whole machine) be
terminated with extreme prejudice.
The trivial sanity check in the vmacache code is *not* such a fatal
error. Recovering from it is absolutely trivial, and using BUG_ON()
just makes it harder to debug for no actual advantage.
To make matters worse, the placement of the BUG_ON() (only if the range
check matched) actually makes it harder to hit the sanity check to begin
with, so _if_ there is a bug (and we just got a report from Srivatsa
Bhat that this can indeed trigger), it is harder to debug not just
because the machine is possibly dead, but because we don't have better
coverage.
BUG_ON() must *die*. Maybe we should add a checkpatch warning for it,
because it is simply just about the worst thing you can ever do if you
hit some "this cannot happen" situation.
Reported-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Cc: Davidlohr Bueso <davidlohr@hp.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
net: ipv6: more places need LOOPBACK_IFINDEX for flowi6_iif
To properly match iif in ip rules we have to provide
LOOPBACK_IFINDEX in flowi6_iif, not 0. Some ip6mr_fib_lookup
and fib6_rule_lookup callers need such fix.
Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: David S. Miller <davem@davemloft.net>
[ tries to modify code, but it's RO, and fails!
ftrace_bug() is called]
When this race happens, ftrace_bug() will produces a nasty warning and
all of the function tracing features will be disabled until reboot.
The simple solution is to treate module load the same way the core
kernel is treated at boot. To hardcode the ftrace function modification
of converting calls to mcount into nops. This is done in init/main.c
there's no reason it could not be done in load_module(). This gives
a better control of the changes and doesn't tie the state of the
module to its notifiers as much. Ftrace is special, it needs to be
treated as such.
The reason this would work, is that the ftrace_module_init() would be
called while the module is in MODULE_STATE_UNFORMED, which is ignored
by the set_all_module_text_ro() call.
Hui Wang [Mon, 28 Apr 2014 06:45:00 +0000 (14:45 +0800)]
ALSA: hda - add headset mic detect quirk for a Dell laptop
When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0255,
SID: 0x10280674), the headset mic can't be detected, after apply this
patch, the headset mic can work well.
BugLink: https://bugs.launchpad.net/bugs/1297581 Cc: David Henningsson <david.henningsson@canonical.com> Cc: stable@vger.kernel.org Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge tag 'asoc-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.15
A smattering of driver-specific fixes here, nothing generic. The Cirrus
CODEC conversions to devm_ are leak fixes - the conversion adds missing
error handling code.
WARNING: vmlinux.o(.text+0x1efc4): Section mismatch in reference from
the function apm821xx_pciex_init_port_hw() to the function
.init.text:ppc4xx_pciex_wait_on_sdr.isra.9()
The function apm821xx_pciex_init_port_hw() references the function
__init ppc4xx_pciex_wait_on_sdr.isra.9(). This is often because
apm821xx_pciex_init_port_hw lacks a __init annotation or the
annotation of ppc4xx_pciex_wait_on_sdr.isra.9 is wrong.
apm821xx_pciex_init_port_hw is only referenced by a struct in
__initdata, so it should be safe to add __init to
apm821xx_pciex_init_port_hw.
Signed-off-by: Alistair Popple <alistair@popple.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
ppc/kvm: Clear the runlatch bit of a vcpu before napping
When the guest cedes the vcpu or the vcpu has no guest to
run it naps. Clear the runlatch bit of the vcpu before
napping to indicate an idle cpu.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@samba.org> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
ppc/kvm: Set the runlatch bit of a CPU just before starting guest
The secondary threads in the core are kept offline before launching guests
in kvm on powerpc: "371fefd6f2dc4666:KVM: PPC: Allow book3s_hv guests to use
SMT processor modes."
Hence their runlatch bits are cleared. When the secondary threads are called
in to start a guest, their runlatch bits need to be set to indicate that they
are busy. The primary thread has its runlatch bit set though, but there is no
harm in setting this bit once again. Hence set the runlatch bit for all
threads before they start guest.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@samba.org> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
ppc/powernv: Set the runlatch bits correctly for offline cpus
Up until now we have been setting the runlatch bits for a busy CPU and
clearing it when a CPU enters idle state. The runlatch bit has thus
been consistent with the utilization of a CPU as long as the CPU is online.
However when a CPU is hotplugged out the runlatch bit is not cleared. It
needs to be cleared to indicate an unused CPU. Hence this patch has the
runlatch bit cleared for an offline CPU just before entering an idle state
and sets it immediately after it exits the idle state.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@samba.org> Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Li Zhong [Thu, 10 Apr 2014 08:25:31 +0000 (16:25 +0800)]
powerpc/pseries: Protect remove_memory() with device hotplug lock
While testing memory hot-remove, I found following dead lock:
Process #1141 is drmgr, trying to remove some memory, i.e. memory499.
It holds the memory_hotplug_mutex, and blocks when trying to remove file
"online" under dir memory499, in kernfs_drain(), at
wait_event(root->deactivate_waitq,
atomic_read(&kn->active) == KN_DEACTIVATED_BIAS);
Process #1120 is trying to online memory499 by
echo 1 > memory499/online
In .kernfs_fop_write, it uses kernfs_get_active() to increase
&kn->active, thus blocking process #1141. While itself is blocked later
when trying to acquire memory_hotplug_mutex, which is held by process
This patch uses lock_device_hotplug() to protect remove_memory() called
in pseries_remove_memblock(), which is also stated before function
remove_memory():
* NOTE: The caller must call lock_device_hotplug() to serialize hotplug
* and online/offline operations before this call, as required by
* try_offline_node().
*/
void __ref remove_memory(int nid, u64 start, u64 size)
With this lock held, the other process(#1120 above) trying to online the
memory block will retry the system call when calling
lock_device_hotplug_sysfs(), and finally find No such device error.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We have two definitions of COMMAND_LINE_SIZE, one for the kernel
and one for the boot wrapper. I assume this is so the boot
wrapper can be self sufficient and not rely on kernel headers.
Having two defines with the same name is confusing, I just
updated the wrong one when trying to bump it.
Make the boot wrapper define unique by calling it
BOOT_COMMAND_LINE_SIZE.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Karl Heiss [Fri, 25 Apr 2014 18:26:30 +0000 (14:26 -0400)]
net: sctp: Don't transition to PF state when transport has exhausted 'Path.Max.Retrans'.
Don't transition to the PF state on every strike after 'Path.Max.Retrans'.
Per draft-ietf-tsvwg-sctp-failover-03 Section 5.1.6:
Additional (PMR - PFMR) consecutive timeouts on a PF destination
confirm the path failure, upon which the destination transitions to the
Inactive state. As described in [RFC4960], the sender (i) SHOULD notify
ULP about this state transition, and (ii) transmit heartbeats to the
Inactive destination at a lower frequency as described in Section 8.3 of
[RFC4960].
This also prevents sending SCTP_ADDR_UNREACHABLE to the user as the state
bounces between SCTP_INACTIVE and SCTP_PF for each subsequent strike.
Signed-off-by: Karl Heiss <kheiss@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Hartkopp [Sat, 26 Apr 2014 19:18:32 +0000 (21:18 +0200)]
slip: fix spinlock variant
With commit cc9fa74e2a ("slip/slcan: added locking in wakeup function") a
formerly missing locking was added to slip.c and slcan.c by Andre Naujoks.
Alexander Stein contributed the fix 367525c8c2 ("can: slcan: Fix spinlock
variant") as the kernel lock debugging advised to use spin_lock_bh() instead
of just using spin_lock().
This fix has to be applied to the same code section in slip.c for the same
reason too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Anton Blanchard [Tue, 22 Apr 2014 05:01:26 +0000 (15:01 +1000)]
powerpc/powernv: Create OPAL sglist helper functions and fix endian issues
We have two copies of code that creates an OPAL sg list. Consolidate
these into a common set of helpers and fix the endian issues.
The flash interface embedded a version number in the num_entries
field, whereas the dump interface did did not. Since versioning
wasn't added to the flash interface and it is impossible to add
this in a backwards compatible way, just remove it.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Tue, 22 Apr 2014 05:01:25 +0000 (15:01 +1000)]
powerpc/powernv: Fix little endian issues in OPAL error log code
Fix little endian issues with the OPAL error log code.
Signed-off-by: Anton Blanchard <anton@samba.org> Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Tue, 22 Apr 2014 05:01:22 +0000 (15:01 +1000)]
powerpc/powernv: Use uint64_t instead of size_t in OPAL APIs
Using size_t in our APIs is asking for trouble, especially
when some OPAL calls use size_t pointers.
Signed-off-by: Anton Blanchard <anton@samba.org> Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Wei Yang [Wed, 23 Apr 2014 02:26:32 +0000 (10:26 +0800)]
powerpc/powernv: Reduce multi-hit of iommu_add_device()
During the EEH hotplug event, iommu_add_device() will be invoked three times
and two of them will trigger warning or error.
The three times to invoke the iommu_add_device() are:
pci_device_add
...
set_iommu_table_base_and_group <- 1st time, fail
device_add
...
tce_iommu_bus_notifier <- 2nd time, succees
pcibios_add_pci_devices
...
pcibios_setup_bus_devices <- 3rd time, re-attach
The first time fails, since the dev->kobj->sd is not initialized. The
dev->kobj->sd is initialized in device_add().
The third time's warning is triggered by the re-attach of the iommu_group.
After applying this patch, the error
iommu_tce: 0003:05:00.0 has not been added, ret=-14
This patch removes iommu_add_device() in pnv_pci_ioda_dma_dev_setup(), which
revert part of the change in commit d905c5df(PPC: POWERNV: move
iommu_add_device earlier).
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/powernv: Fix kexec races going back to OPAL
We have a subtle race when sending CPUs back to OPAL on kexec.
We mark them as "in real mode" right before we send them down. Once
we've booted the new kernel, it might try to call opal_reinit_cpus()
to change endianness, and that requires all CPUs to be spinning inside
OPAL.
However there is no synchronization here and we've observed cases
where the returning CPUs hadn't established their new state inside
OPAL before opal_reinit_cpus() is called, causing it to fail.
The proper fix is to actually wait for them to go down all the way
from the kexec'ing kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Joel Stanley [Thu, 24 Apr 2014 07:25:37 +0000 (16:55 +0930)]
powerpc/powernv: Check sysparam size before creation
The size of the sysparam sysfs files is determined from the device tree
at boot. However the buffer is hard coded to 64 bytes. If we encounter a
parameter that is larger than 64, or miss-parse the device tree, the
buffer will overflow when reading or writing to the parameter.
Check it at discovery time, and if the parameter is too large, do not
create a sysfs entry for it.
Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Joel Stanley [Thu, 24 Apr 2014 07:25:34 +0000 (16:55 +0930)]
powerpc/powernv: Use ssize_t for sysparam return values
The OPAL calls are returning int64_t values, which the sysparam code
stores in an int, and the sysfs callback returns ssize_t. Make code a
easier to read by consistently using ssize_t.
Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When a sysparam query in OPAL returned a negative value (error code),
sysfs would spew out a decent chunk of memory; almost 64K more than
expected. This was traced to a sign/unsigned mix up in the OPAL sysparam
sysfs code at sys_param_show.
The return value of sys_param_show is a ssize_t, calculated using
return ret ? ret : attr->param_size;
Alan Modra explains:
"attr->param_size" is an unsigned int, "ret" an int, so the overall
expression has type unsigned int. Result is that ret is cast to
unsigned int before being cast to ssize_t.
Instead of using the ternary operator, set ret to the param_size if an
error is not detected. The same bug exists in the sysfs write callback;
this patch fixes it in the same way.
A note on debugging this next time: on my system gcc will warn about
this if compiled with -Wsign-compare, which is not enabled by -Wall,
only -Wextra.
Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Li Zhong [Mon, 28 Apr 2014 00:29:51 +0000 (08:29 +0800)]
powerpc: Fix Oops in rtas_stop_self()
commit 41dd03a9 may cause Oops in rtas_stop_self().
The reason is that the rtas_args was moved into stack space. For a box
with more that 4GB RAM, the stack could easily be outside 32bit range,
but RTAS is 32bit.
So the patch moves rtas_args away from stack by adding static before
it.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Signed-off-by: Anton Blanchard <anton@samba.org> Cc: stable@vger.kernel.org # 3.14+ Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Jeff Mahoney [Sun, 27 Apr 2014 22:10:43 +0000 (18:10 -0400)]
powerpc: Export flush_icache_range
Commit aac416fc38c (lkdtm: flush icache and report actions) calls
flush_icache_range from a module. It's exported on most architectures
that implement it, but not on powerpc. This patch exports it to fix
the module link failure.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
David S. Miller [Mon, 28 Apr 2014 02:05:22 +0000 (22:05 -0400)]
Merge branch 'qmi_wwan'
Bjørn Mork says:
====================
qmi_wwan: adding a few new devices
Adding some new and some old QMI devices. A similar series for
usb-serial support will be posted as well.
These new device ID patches should also go to all maintained stable kernels
where they apply. I believe that should be stable-3.10 and newer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: AceLan Kao <acelan.kao@canonical.com> Reported-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Device interface layout:
0: ff/ff/ff - serial
1: ff/ff/ff - serial AT+PPP
2: 08/06/50 - storage
3: ff/ff/ff - serial
4: ff/ff/ff - QMI/wwan
Reported-by: Julio Araujo <julio.araujo@wllctel.com.br> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Rusty Russell [Mon, 28 Apr 2014 01:35:43 +0000 (11:05 +0930)]
module: remove warning about waiting module removal.
We remove the waiting module removal in commit 3f2b9c9cdf38 (September
2013), but it turns out that modprobe in kmod (< version 16) was
asking for waiting module removal. No one noticed since modprobe would
check for 0 usage immediately before trying to remove the module, and
the race is unlikely.
However, it means that anyone running old (but not ancient) kmod
versions is hitting the printk designed to see if anyone was running
"rmmod -w". All reports so far have been false positives, so remove
the warning.
Fixes: 3f2b9c9cdf389e303b2273679af08aab5f153517 Reported-by: Valerio Vanni <valerio.vanni@inwind.it> Cc: Elliott, Robert (Server Storage) <Elliott@hp.com> Cc: stable@kernel.org Acked-by: Lucas De Marchi <lucas.de.marchi@gmail.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
commit 813b3b5db83 (ipv4: Use caller's on-stack flowi as-is
in output route lookups.) introduces another regression which
is very similar to the problem of commit e6b45241c (ipv4: reset
flowi parameters on route connect) wants to fix:
Before we call ip_route_output_key() in sctp_v4_get_dst() to
get a dst that matches a bind address as the source address,
we have already called this function previously and the flowi
parameters have been initialized including flowi4_oif, so when
we call this function again, the process in __ip_route_output_key()
will be different because of the setting of flowi4_oif, and we'll
get a networking device which corresponds to the inputted flowi4_oif
as the output device, this is wrong because we'll never hit this
place if the previously returned source address of dst match one
of the bound addresses.
To reproduce this problem, a vlan setting is enough:
# ifconfig eth0 up
# route del default
# vconfig add eth0 2
# vconfig add eth0 3
# ifconfig eth0.2 10.0.1.14 netmask 255.255.255.0
# route add default gw 10.0.1.254 dev eth0.2
# ifconfig eth0.3 10.0.0.14 netmask 255.255.255.0
# ip rule add from 10.0.0.14 table 4
# ip route add table 4 default via 10.0.0.254 src 10.0.0.14 dev eth0.3
# sctp_darn -H 10.0.0.14 -P 36422 -h 10.1.4.134 -p 36422 -s -I
You'll detect that all the flow are routed to eth0.2(10.0.1.254).
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com> Signed-off-by: Julian Anastasov <ja@ssi.bg> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This adds ability for the arc_emac to really handle its supplying clock.
To get the needed clock-frequency either a real clock or the previous
clock-frequency property must be provided.
Signed-off-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Max Schwarz <max.schwarz@online.de> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: Handle IFLA_ADDRESS correctly when creating bridge device
When bridge device is created with IFLA_ADDRESS, we are not calling
br_stp_change_bridge_id(), which leads to incorrect local fdb
management and bridge id calculation, and prevents us from receiving
frames on the bridge device.
Reported-by: Tom Gundersen <teg@jklm.no> Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
Will Deacon [Wed, 23 Apr 2014 16:52:52 +0000 (17:52 +0100)]
word-at-a-time: avoid undefined behaviour in zero_bytemask macro
The asm-generic, big-endian version of zero_bytemask creates a mask of
bytes preceding the first zero-byte by left shifting ~0ul based on the
position of the first zero byte.
Unfortunately, if the first (top) byte is zero, the output of
prep_zero_mask has only the top bit set, resulting in undefined C
behaviour as we shift left by an amount equal to the width of the type.
As it happens, GCC doesn't manage to spot this through the call to fls(),
but the issue remains if architectures choose to implement their shift
instructions differently.
An example would be arch/arm/ (AArch32), where LSL Rd, Rn, #32 results
in Rd == 0x0, whilst on arch/arm64 (AArch64) LSL Xd, Xn, #64 results in
Xd == Xn.
Rather than check explicitly for the problematic shift, this patch adds
an extra shift by 1, replacing fls with __fls. Since zero_bytemask is
never called with a zero argument (has_zero() is used to check the data
first), we don't need to worry about calling __fls(0), which is
undefined.
Cc: <stable@vger.kernel.org> Cc: Victor Kamensky <victor.kamensky@linaro.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This merges the patch to fix possible loss of dirty bit on munmap() or
madvice(DONTNEED). If there are concurrent writers on other CPU's that
have the unmapped/unneeded page in their TLBs, their writes to the page
could possibly get lost if a third CPU raced with the TLB flush and did
a page_mkclean() before the page was fully written.
Admittedly, if you unmap() or madvice(DONTNEED) an area _while_ another
thread is still busy writing to it, you deserve all the lost writes you
could get. But we kernel people hold ourselves to higher quality
standards than "crazy people deserve to lose", because, well, we've seen
people do all kinds of crazy things.
So let's get it right, just because we can, and we don't have to worry
about it.
* safe-dirty-tlb-flush:
mm: split 'tlb_flush_mmu()' into tlb flushing and memory freeing parts
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: limit the path size in send to PATH_MAX
Btrfs: correctly set profile flags on seqlock retry
Btrfs: use correct key when repeating search for extent item
Btrfs: fix inode caching vs tree log
Btrfs: fix possible memory leaks in open_ctree()
Btrfs: avoid triggering bug_on() when we fail to start inode caching task
Btrfs: move btrfs_{set,clear}_and_info() to ctree.h
btrfs: replace error code from btrfs_drop_extents
btrfs: Change the hole range to a more accurate value.
btrfs: fix use-after-free in mount_subvol()
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
Pull arm fixes from Russell King:
"A number of fixes for the PJ4/iwmmxt changes which arm-soc forced me
to take during the merge window. This stuff should have been better
tested and sorted out *before* the merge window"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8042/1: iwmmxt: allow to build iWMMXt on Marvell PJ4B
ARM: 8041/1: pj4: fix cpu_is_pj4 check
ARM: 8040/1: pj4: properly detect existence of iWMMXt coprocessor
ARM: 8039/1: pj4: enable iWMMXt only if CONFIG_IWMMXT is set
ARM: 8038/1: iwmmxt: explicitly check for supported architectures
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A slighlty large fix for a subtle issue in the CPU hotplug code of
certain ARM SoCs, where the not yet online cpu needs to setup the cpu
local timer and needs to set the interrupt affinity to itself.
Setting interrupt affinity to a not online cpu is prohibited and
therefor the timer interrupt ends up on the wrong cpu, which leads to
nasty complications.
The SoC folks tried to hack around that in the SoC code in some more
than nasty ways. The proper solution is to have a way to enforce the
affinity setting to a not online cpu. The core patch to the genirq
code provides that facility and the follow up patches make use of it
in the GIC interrupt controller and the exynos timer driver.
The change to the core code has no implications to existing users,
except for the rename of the locked function and therefor the
necessary fixup in mips/cavium. Aside of that, no runtime impact is
possible, as none of the existing interrupt chips implements anything
which depends on the force argument of the irq_set_affinity()
callback"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: Exynos_mct: Register clock event after request_irq()
clocksource: Exynos_mct: Use irq_force_affinity() in cpu bringup
irqchip: Gic: Support forced affinity setting
genirq: Allow forcing cpu affinity of interrupts
Merge tag 'tty-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few tty/serial fixes for 3.15-rc3 that resolve a number of
reported issues in the 8250 and samsung serial drivers, as well as a
character loss fix for the tty core that was caused by the lock
removal patches a release ago"
* tag 'tty-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial_core: fix uart PORT_UNKNOWN handling
serial: samsung: Change barrier() to cpu_relax() in console output
serial: samsung: don't check config for every character
serial: samsung: Use the passed in "port", fixing kgdb w/ no console
serial: 8250: Fix thread unsafe __dma_tx_complete function
8250_core: Fix unwanted TX chars write
tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc
Merge tag 'staging-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver fixes from Greg KH:
"Here are some small staging and IIO driver fixes for 3.15-rc3.
Nothing major at all, just some assorted issues that people have
reported"
* tag 'staging-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: usbdux: bug fix for accessing 'ao_chanlist' in private data
iio: adc: mxs-lradc: fix warning when buidling on avr32
iio: cm36651: Fix i2c client leak and possible NULL pointer dereference
iio: querying buffer scan_mask should return 0/1
staging:iio:ad2s1200 fix a missing break
iio: adc: at91_adc: correct default shtim value
ARM: at91: at91sam9260: change at91_adc name
ARM: at91: at91sam9g45: change at91_adc name
iio: cm32181: Fix read integration time function
iio: adc: at91_adc: Repair broken platform_data support
Merge tag 'driver-core-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some kernfs fixes for 3.15-rc3 that resolve some reported
problems. Nothing huge, but all needed"
* tag 'driver-core-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
s390/ccwgroup: Fix memory corruption
kernfs: add back missing error check in kernfs_fop_mmap()
kernfs: fix a subdir count leak
Merge tag 'usb-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 3.15-rc3. The majority are gadget
fixes, as we didn't get any of those in for 3.15-rc2. The others are
all over the place, and there's a number of new device id addtions as
well."
* tag 'usb-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (35 commits)
usb: option: add and update a number of CMOTech devices
usb: option: add Alcatel L800MA
usb: option: add Olivetti Olicard 500
usb: qcserial: add Sierra Wireless MC7305/MC7355
usb: qcserial: add Sierra Wireless MC73xx
usb: qcserial: add Sierra Wireless EM7355
USB: io_ti: fix firmware download on big-endian machines
usb/xhci: fix compilation warning when !CONFIG_PCI && !CONFIG_PM
xhci: extend quirk for Renesas cards
xhci: Switch Intel Lynx Point ports to EHCI on shutdown.
usb: xhci: Prefer endpoint context dequeue pointer over stopped_trb
phy: core: make NULL a valid phy reference if !CONFIG_GENERIC_PHY
phy: fix kernel oops in phy_lookup()
phy: restore OMAP_CONTROL_PHY dependencies
phy: exynos: fix building as a module
USB: serial: fix sysfs-attribute removal deadlock
usb: wusbcore: fix panic in wusbhc_chid_set
usb: wusbcore: convert nested lock to use spin_lock instead of spin_lock_irq
uwb: don't call spin_unlock_irq in a USB completion handler
usb: chipidea: coordinate usb phy initialization for different phy type
...
Merge tag 'pm+acpi-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These include a fix for a recent ACPI regression related to device
notifications, intel_idle fix related to IvyTown support, fix for a
buffer size issue in ACPICA, PM core fix related to the "freeze" sleep
state, four fixes for various types of breakage in cpufreq drivers, a
PNP workaround for a wrong memory region size in ACPI tables, and a
fix and cleanup for the ACPI tools Makefile.
Specifics:
- Fix for broken ACPI notifications on some systems caused by a
recent ACPI hotplug commit that blocked the propagation of unknown
type notifications to device drivers inadvertently.
- intel_idle fix to make the IvyTown C-states handling (added
recently) work as intended which now is broken due to missing
braces. From Christoph Jaeger.
- ACPICA fix to make it allocate buffers of the right sizes for the
Generic Serial Bus operation region access. From Lv Zheng.
- PM core fix unblocking cpuidle before entering the "freeze" sleep
state which causes that state to be able to actually save more
energy than runtime idle.
- Configuration and build fixes for the highbank and powernv cpufreq
drivers from Kefeng Wang and Srivatsa S Bhat.
- Coccinelle warning fix related to error pointers for the unicore32
cpufreq driver from Duan Jiong.
- Integer overflow fix for the ppc-corenet cpufreq driver from Geert
Uytterhoeven.
- Workaround for BIOSes that don't report the entire Intel MCH area
in their ACPI tables from Bjorn Helgaas.
- ACPI tools Makefile fix and cleanup from Thomas Renninger"
* tag 'pm+acpi-3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / notify: Do not block unknown type notifications in root handler
PNP: Work around BIOS defects in Intel MCH area reporting
cpufreq: highbank: fix ARM_HIGHBANK_CPUFREQ dependency warning
cpufreq: ppc: Fix integer overflow in expression
cpufreq, powernv: Fix build failure on UP
cpufreq: unicore32: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
PM / suspend: Make cpuidle work in the "freeze" state
intel_idle: fix IVT idle state table setting
ACPICA: Fix buffer allocation issue for generic_serial_bus region accesses.
tools/power/acpi: Minor bugfixes
Jacob Keller [Fri, 25 Apr 2014 01:05:03 +0000 (18:05 -0700)]
i40e: fix Timesync Tx interrupt handler code
This patch fixes the PTP Tx timestamp interrupt handler. The original
code misinterpreted the interrupt handler design. We were clearing the
ena_mask bit for the Timesync interrupts. This is done to indicate that
the interrupt will be handled in a scheduled work item (instead of
immediately) and that work item is responsible for re-enabling the
interrupts. However, the Tx timestamp was being handled immediately and
nothing was ever re-enabling it. This resulted in a single interrupt
working for the life of the driver.
This patch fixes the issue by instead clearing the bit from icr0 which
is used to indicate that the interrupt was immediately handled and can
be re-enabled right away. This patch also clears up a related issue due
to writing the PRTTSYN_STAT_0 register, which was unintentionally
clearing the cause bits for Timesync interrupts.
Change-ID: I057bd70d53c302f60fab78246989cbdfa469d83b Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Acked-by: Anjali Singhai Jain <anjali.singhai@intel.com> Acked-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 26 Apr 2014 16:29:19 +0000 (12:29 -0400)]
Merge tag 'linux-can-fixes-for-3.15-20140424' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
this is a pull request for net/master, for the v3.15 release cycle, consisting
of 26 patches.
Thomas Gleixner contributes 21 patches for the c_can driver, which address
several shortcomings in the driver like hardware initialisation, concurrency,
message ordering and poor performance. Two patches Oliver Hartkopp, one adds a
missing lock to the sja1000_isa driver, the other one fixes the return value in
the generic bit time configuration function. And finally a patch by Alexander
Stein, that fixes the slcan driver to use the correct spinlock variant.
To make it 26 patches, Wolfgang Grandegger patch for the c_can_pci
driver, which enables the bus master only for MSI and a patch by
Wolfram Sang, which converts the 'instance' in the c_can driver to the
proper type.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 26 Apr 2014 16:27:14 +0000 (12:27 -0400)]
Merge branch 'altera_tse'
Vince Bridgers says:
====================
This series of patches addresses a handful of issues found in testing
and reported by users of the Altera Triple Speed Ethernet soft IP.
The patches address the following issues (in summary)
1) The SGDMA soft IP was found to incorrectly process receive packets
when the target physical address of the receive buffer was on
a boundary that's not 32-bit aligned. One of the patches addresses
this issue.
2) The pause quanta was not being set by the driver, one patch of this
series sets the pause quanta to the IEEE defined default value
since the hardware reset value is 0.
3) An issue in a error recovery path of the probe routine caused a
kernel panic in the event a phy was probed and could not be found.
A patch addresses this issue.
4) A change was made to the driver name for Ethtool support, and
comments added to support an addition to Ethtool to support
the Altera Triple Speed Ethernet controller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the name used by Ethtool to something more
conventional in preparation for TSE Ethtool register dump
support to be added in the near future.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Altera TSE: Fix Panic in probe routine when phy probe fails
This patch addresses a fault in the error recovery path of the probe
routine where the netdev structure was not being unregistered properly
leading to a panic only when the phy probe failed.
Abbreviated panic stack seen is as follows:
(free_netdev+0xXX) from (altera_tse_probe+0xXX)
(altera_tse_probe+0xXX) from (platform_drv_probe+0xXX)
(platform_drv_probe+0xXX) from (driver_probe_device+0xXX)
(driver_probe_device+0xXX) from (__driver_attach+0xXX)
(__driver_attach+0xXX) from (bus_for_each_dev+0xXX)
(bus_for_each_dev+0xXX) from (driver_attach+0xXX)
(driver_attach+0xXX) from (bus_add_driver+0xXX)
(bus_add_driver+0xXX) from (driver_register+0xXX)
(driver_register+0xXX) from (__platform_driver_register+0xXX)
(__platform_driver_register+0xXX) from (altera_tse_driver_init+0xXX)
(altera_tse_driver_init+0xXX) from (do_one_initcall+0xXX)
(do_one_initcall+0xXX) from (kernel_init_freeable+0xXX)
(kernel_init_freeable+0xXX) from (kernel_init+0xXX)
(kernel_init+0xXX) from (ret_from_fork+0xXX)
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Altera TSE: Work around unaligned DMA receive packet issue with Altera SGDMA
This patch works around a recently discovered unaligned receive dma problem
with the Altera SGMDA. The Altera SGDMA component cannot be configured to
DMA data to unaligned addresses for receive packet operations from the
Triple Speed Ethernet component because of a potential data transfer
corruption that can occur. This patch addresses this issue by
utilizing the shift 16 bits feature of the Altera Triple Speed Ethernet
component and modifying the receive buffer physical addresses accordingly
such that the target receive DMA address is always aligned on a 32-bit
boundary.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com> Tested-by: Matthew Gerlach <mgerlach@altera.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 26 Apr 2014 16:16:18 +0000 (12:16 -0400)]
Merge branch 'bnx2x-net'
Yuval Mintz says:
====================
bnx2x: SRIOV bug fixes
This series contains 3 SRIOV bug fixes, 2 of which are regressions starting
with commit 2dc33bbc "bnx2x: Remove the sriov VFOP mechanism".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 2dc33bbc "bnx2x: Remove the sriov VFOP mechanism",
the bnx2x started enforcing vlan credits for all vlan configurations.
This exposed 2 issues:
- Vlan credits are not returned once a VF is removed; this causes a leak
of credits, and eventually will lead to VFs with no vlan credits.
- A vlan credit must be set aside for the Hypervisor to use, and should
not be visible to the VF.
Although linux VFs at the moment do not support vlan configuration [from the
VF side] which causes them to be resilient to this sort of issue, Windows VF
over linux hypervisors might fail to load as the vlan credits become depleted.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a VF interface, the driver fails to release that VF's mailbox
and bulletin board allocated memory.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Mason [Sat, 26 Apr 2014 12:02:03 +0000 (05:02 -0700)]
Btrfs: limit the path size in send to PATH_MAX
fs_path_ensure_buf is used to make sure our path buffers for
send are big enough for the path names as we construct them.
The buffer size is limited to 32K by the length field in
the struct.
But bugs in the path construction can end up trying to build
a huge buffer, and we'll do invalid memmmoves when the
buffer length field wraps.
mm: split 'tlb_flush_mmu()' into tlb flushing and memory freeing parts
The mmu-gather operation 'tlb_flush_mmu()' has done two things: the
actual tlb flush operation, and the batched freeing of the pages that
the TLB entries pointed at.
This splits the operation into separate phases, so that the forced
batched flushing done by zap_pte_range() can now do the actual TLB flush
while still holding the page table lock, but delay the batched freeing
of all the pages to after the lock has been dropped.
This in turn allows us to avoid a race condition between
set_page_dirty() (as called by zap_pte_range() when it finds a dirty
shared memory pte) and page_mkclean(): because we now flush all the
dirty page data from the TLB's while holding the pte lock,
page_mkclean() will be held up walking the (recently cleaned) page
tables until after the TLB entries have been flushed from all CPU's.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Dave Hansen <dave.hansen@intel.com> Acked-by: Hugh Dickins <hughd@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Russell King - ARM Linux <linux@arm.linux.org.uk> Cc: Tony Luck <tony.luck@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / karo-tx-linux.git / log