Support for tuners with i2c addresses >= 0x65 is dropped since no tuners
with addresses in the range 0x65-0x6f have been found.
This patch removes addresses 0x65-0x6f from the list of tuner probe addresses,
it removes the kernel warning that warned if addresses in this range appeared,
and it removed a hack for the cx88 that is no longer needed now that the
tuner address range is reduced.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
/home/v4l/master/v4l/radio-si470x.c: In function 'si470x_fops_release':
/home/v4l/master/v4l/radio-si470x.c:1218: warning: label 'unlock' defined but not used
Erik Andrén [Thu, 22 Jan 2009 06:32:32 +0000 (03:32 -0300)]
V4L/DVB (11639): gspca - m5602-mt9m111: Correct the hflip/vflip semantics
mt9m111: Hflip and vflip shall always be 0 at start and the image shall be correctly aligned.
The mt9m111 is hflipped and vflipped by default. Correct the semantics to make this happen.
Signed-off-by: Erik Andrén <erik.andren@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 26 Apr 2009 21:46:14 +0000 (18:46 -0300)]
V4L/DVB (11624): cx18: Toggle the AI1 mux when changing the CX18_AUDIO_ENABLE register
Toggle the AI1 mux when changing the CX18_AUDIO_ENABLE register. It's hard to
reliably tell when we have written to this register successfully unless we
change some bits we know we can read back. The AI mux bits always read back
what we wrote to them, so force them to toggle whenever we have to write to
the register, so we can tell we wrote to the register successfully.
This change was prompted by users experiencing broadcast audio decoding
problems after the cx18 module loads for the first time.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code to verify the cx18-av-core digitizer firmware loads correctly. The
verification function reads back and compares the firmware bytes loaded
into the A/V core. The result of the verification is only used to log a
message in the system log.
This change was prompted by users with multiple card setups that have problems
with broadcast audio decoding the first time the cx18 module is loaded.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sun, 26 Apr 2009 19:34:36 +0000 (16:34 -0300)]
V4L/DVB (11622): cx18: Allow IVTV format VBI insertion in MPEG-2 SVCD and DVD streams
Both the MPEG-2 SVCD stream format and the MPEG-2 DVD stream format should
use an MPEG-2 PS container. This makes it safe to stuff IVTV Private Stream 1
VBI packets in these stream types using the existing cx18 driver routines.
Reported-by: Helen Buus <mythtv@hbuus.com> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Wed, 15 Apr 2009 23:45:10 +0000 (20:45 -0300)]
V4L/DVB (11619): cx18: Simplify the work handler for outgoing mailbox commands
Simplify the way outgoing work handler gets scheduled to send empty buffers
back to the firmware for use. Also reduced the memory required for scheduling
this outgoing work, by using a single, per stream work object.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Tue, 14 Apr 2009 02:08:00 +0000 (23:08 -0300)]
V4L/DVB (11618): cx18: Convert per stream mutex locks to per queue spin locks
To avoid sleeps in providing buffers to user space and in handling incoming
buffers from the capture unit, converted the per stream mutex for locking
queues to 3 spin locks. There is now a spin lock per queue
to increase concurrency when moving buffers around.
Also simplified queue manipulations and buffer handling of incoming buffers
of data from the capture unit.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Tue, 14 Apr 2009 01:53:09 +0000 (22:53 -0300)]
V4L/DVB (11617): cx18: Set up to wait for a one-shot response before sending a firmware cmd
When sending an outgoing firmware command, prepare to wait before we raise the
interrupt, so we don't miss the wake_up() on the acknowledgment. When waiting
for the acknowledgement, there is no need to loop around schedule(), as there
will only be one interrupt, and hence one wake_up(), issued.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Tue, 14 Apr 2009 01:42:43 +0000 (22:42 -0300)]
V4L/DVB (11616): cx18: Add a work queue for deferring empty buffer handoffs to the firmware
This change defers sending all CX18_CPU_DE_SET_MDL commands, for a stream with
an ongoing capture, by adding a work queue to handle sending such commands when
needed. This prevents any sleeps, caused by notifying the firmware of new
usable buffers, when a V4L2 application read() is being satisfied or when
an incoming buffer is processed by the cx18-NN-in work queue thread.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Tue, 14 Apr 2009 01:22:40 +0000 (22:22 -0300)]
V4L/DVB (11615): cx18: Rename the work queue to "in_work_queue"
Rename the work queue to "in_work_queue" to indicate it is handling
incoming mailbox commands. This is preparation for adding a work queue
for handling deferrable outgoing mailbox commands.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (11611): soc-camera: link host drivers after clients
With the transition of soc-camera to become a platform driver and to the
v4l2-subdev framework the initialisation order becomes important. In case
of a static build clients (i2c) drivers have to be available when host
drivers are probed. Moving host drivers down in the Makefile achieves the
desired order.
Embed struct soc_camera_host in platform-specific per host instance objects
instead of allocating them statically in drivers, use platform_[gs]et_drvdata
consistently, use resource_size().
V4L/DVB (11607): soc-camera: add a free_bus method to struct soc_camera_link
Currently pcm990 camera bus-width management functions request a GPIO and never
free it again. With this approach the GPIO extender driver cannot be unloaded
once camera drivers have been loaded, also unloading theb i2c-pxa bus driver
produces errors, because the GPIO extender driver cannot unregister properly.
Another problem is, that if camera drivers are once loaded before the GPIO
extender driver, the platform code marks the GPIO unavailable and only a reboot
helps to recover. Adding an explicit free_bus method and using it in mt9m001
and mt9v022 drivers fixes these problems.
V4L/DVB (11567): saa7134: Added support for AVerMedia Cardbus Plus
Here comes the full support for AVerMedia Cardbus Plus (E501R) - including
remote control. TV, Composite and FM radio tested, I don't have S-Video to
test. I've figured out that the radio works only with xtal frequency 13MHz.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Thu, 23 Apr 2009 18:00:04 +0000 (15:00 -0300)]
V4L/DVB (11600): budget: Use Continuous clock
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Thu, 23 Apr 2009 17:59:36 +0000 (14:59 -0300)]
V4L/DVB (11599): S2-1600: Use budget driver instead of budged-ci
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Thu, 23 Apr 2009 17:59:03 +0000 (14:59 -0300)]
V4L/DVB (11598): stv090x: fix missing wakeup in init
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Thu, 23 Apr 2009 17:58:36 +0000 (14:58 -0300)]
V4L/DVB (11597): stv090x: fixes read_status to return 0 in case of no error
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Thu, 23 Apr 2009 17:57:24 +0000 (14:57 -0300)]
V4L/DVB (11596): stv090x: fixes some register definitions
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Thu, 23 Apr 2009 17:56:41 +0000 (14:56 -0300)]
V4L/DVB (11595): stv090x: fixes a few bugs
This patch fixes:
* Cut revision was read too late
* Missing increment
* wrong return value
* mismatched entries
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Thu, 16 Apr 2009 11:40:36 +0000 (08:40 -0300)]
V4L/DVB (11593): stv090x: Fix Rolloff
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Thu, 16 Apr 2009 11:38:46 +0000 (08:38 -0300)]
V4L/DVB (11592): stv6110x: Fix read bug
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Wed, 8 Apr 2009 20:28:41 +0000 (17:28 -0300)]
V4L/DVB (11585): stv090x: fix incorrectly used mode
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Wed, 8 Apr 2009 20:27:51 +0000 (17:27 -0300)]
V4L/DVB (11584): stv090x: add tone burst control
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Regel [Tue, 7 Apr 2009 19:09:52 +0000 (16:09 -0300)]
V4L/DVB (11583): isl6423: Various fixes to use external modulation
Use external modulation
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: Manu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andreas Regel <andreas.regel@gmx.de> Signed-off-by: MAnu Abraham <manu@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Márton Németh [Wed, 15 Apr 2009 12:01:58 +0000 (09:01 -0300)]
V4L/DVB (11573): uvcvideo: Prevent invormation loss with removing implicit casting
The uvcvideo driver supports only one input, which is input 0. For all
other input index the return value shall be EINVAL. This patch fixes the
problem when the value 0x80000000 was incorrectly casted and treated as
a zero value.
The patch was tested with v4l-test 0.10 [2] with CNF7129 webcam found on
EeePC 901.
References:
[1] V4L2 API specification, revision 0.24
http://v4l2spec.bytesex.org/spec/r11217.htm
[2] v4l-test: Test environment for Video For Linux Two API
http://v4l-test.sourceforge.net/
[Modified by Laurent Pinchart]
Invalid input value (u32)-1 would be accepted due to integer overflow. Make
sure the driver rejects it and returns -EINVAL.
Signed-off-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Tue, 7 Apr 2009 15:55:17 +0000 (12:55 -0300)]
V4L/DVB (11564): tda7432: Delete old driver history
The history of changes does belong to git.
In general I wouldn't care too much but it happens that this specific
comment triggers a false positive in one of my scripts, so I'd rather
get rid of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / mv-sheeva.git / log