Raja Mani [Mon, 22 Jun 2015 14:40:09 +0000 (20:10 +0530)]
ath10k: include new wmi op version for 10.4 fw
qca99X0 chip uses firmware version 10.4. Define a new macro
ATH10K_FW_WMI_OP_VERSION_10_4 for 10.4 firmware and include
in switch cases where ATH10K_FW_WMI_OP_VERSION_* is used
to avoid compilation error.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Code swap is a mechanism to use host memory to store
some fw binary code segment. Ath10k host driver allocates
and loads the code swap binary into the host memory and
configures the target with the host allocated memory
information at the address taken from code swap binary.
This patch adds code swap support for firmware binary.
Code swap binary for firmware bin is available in
ATH10K_FW_IE_FW_CODE_SWAP_IMAGE.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is more than 1 sec delay in getting response from target
through BMI in QCA99X0. Increase the BMI communication timeout
to 2*HZ to fix BMI failures.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: Extend CE src desc flags for interrupt indication
QCA99X0 uses two new copy engine src desc flags for interrupt
indication. Bit_2 is to mark if host interrupt is disabled after
processing the current desc and bit_3 is to mark if target interrupt
is diabled after the processing of current descriptor.
CE_DESC_FLAGS_META_DATA_MASK and CE_DESC_FLAGS_META_DATA_LSB are based
on the target type.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 supports only cold reset. Also, made
ath10k_pci_irq_msi_fw_mask() and ath10k_pci_irq_msi_fw_unmask()
non-99X0 specific till we get proper register configuration
to mask/unmask irq/MSI.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: Make target cpu address to CE address conversion chip specific
Make the helper converting target virtual address space to CE address
space a target type specific to support QCA99X0. Also make this as
function instead of macro.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA99X0 supports upto 12 Copy engines. Host and target
CE configuration table is updated to support new copy engine
pipes. This also fixes the assumption of diagnostic CE by making
CE_7 as the one instead of CE_COUNT - 1.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to prepare the driver for QCA99X0 chip support.
This commit adds hw_params, hw register table and hw_values
table for QCA99X0 chip. Please note this is only a partial patch adding
support for QCA99X0, so the device id is not yet added to pci device
table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k: txrx: remove unreachable negative return check and fixup type
wait_event_timeout(), introduced in 'commit 5e3dd157d7e7 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is == 0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wait_event_timeout(), introduced in 'commit 5e3dd157d7e7 ("ath10k: mac80211
driver for Qualcomm Atheros 802.11ac CQA98xx devices")' never returns < 0
so the only failure condition to be checked is ==0 (timeout). Further the
return type is long not int - an appropriately named variable is added
and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
rt2800: fix assigning same WCID for different stations
On some hardware reading WCID entries table results getting 0xff
numbers, no matter of value written there before. This cause assigning
the same WCID for different stations and makes not possible to connect
to more than one station.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend van Spriel [Wed, 10 Jun 2015 22:12:23 +0000 (00:12 +0200)]
brcmfmac: assure p2pdev is unregistered upon driver unload
When unloading the driver with a p2pdev interface it resulted in
a warning upon calling wiphy_unregister() and subsequently a crash
in the driver. This patch assures the p2pdev is unregistered calling
unregister_wdev() before doing the wiphy_unregister().
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend van Spriel [Wed, 10 Jun 2015 22:12:20 +0000 (00:12 +0200)]
brcmfmac: have sdio return -EIO when device communication is not possible
The bus interface functions txctl and rxctl may be used while the device
can not be accessed, eg. upon driver .remove() callback. This patch will
immediately return -EIO when this is the case which speeds up the module
unload.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arend van Spriel [Wed, 10 Jun 2015 22:12:19 +0000 (00:12 +0200)]
brcmfmac: rework .get_station() callback
The .get_station() cfg80211 callback is used in several scenarios. In
managed mode it can obtain information about the access-point and its
BSS parameters. In managed mode it can also obtain information about
TDLS peers. In AP mode it can obtain information about connected
clients.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pontus Fuchs [Wed, 10 Jun 2015 22:12:18 +0000 (00:12 +0200)]
brcmfmac: Build wiphy mode and interface combinations dynamically
Switch from using semi hard coded interface combinations. This makes
it easier to announce what the firmware actually supports. This fixes
the case where brcmfmac announces p2p but the firmware doesn't
support it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Arend Van Spriel <arend@broadcom.com> Signed-off-by: Pontus Fuchs <pontusf@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jakub Kicinski [Wed, 10 Jun 2015 18:10:09 +0000 (20:10 +0200)]
mt7601u: don't warn about devices without per-rate power table
We expect EEPROM per-rate power table to be filled with
s6 values and warn user if values are invalid. However,
there appear to be devices which don't have this section
of EEPROM initialized. In such case we should ignore
the values and leave the driver power tables set to zero.
Note that vendor driver doesn't care about this case but
mt76x2 skips 0xff per value. We take mt76x2's approach.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chunfan Chen [Wed, 10 Jun 2015 13:19:48 +0000 (06:19 -0700)]
mwifiex: handle BT coex event to adjust Rx BA window size
If timeshare coexistance between bluetooth and WLAN gets enabled,
firmware will give host an event to reduce Rx AMPDU BA window size.
The event is handled in this patch.
Signed-off-by: Chunfan Chen <jeffc@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac: use debugfs_create_devm_seqfile() helper function
Some time ago the function debugfs_create_devm_seqfile() was
introduced in debugfs. The caller simply needs to provide a
device pointer and read function. The function brcmf_debugfs_add_entry()
is now simply a wrapper only doing the work for CONFIG_BRCMDBG.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmfmac: remove watchdog reset from brcmf_pcie_buscoreprep()
The watchdog reset as done in brcmf_pcie_buscoreprep() is not
sufficient. It needs to modify PCIe core registers as well
which is properly done by brcmf_pcie_reset_device() after the
chip recognition is done. So the faulty watchdog reset can be
removed as it was causing driver reload to fail and hang the
system requiring a power-cycle. Instead the call to to the
brcmf_pcie_reset_device() function is done twice in the unload.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com> Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hante Meuleman [Mon, 8 Jun 2015 12:38:32 +0000 (14:38 +0200)]
brcmfmac: Update msgbuf read pointer quicker.
On device to host data using msgbuf the read pointer gets updated
once all data is processed. Updating this pointer more frequently
allows the firmware to add more data quicker. This will result in
slightly higher and more stable throughput on CPU bounded host
processors.
Reviewed-by: Arend Van Spriel <arend@broadcom.com> Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: Hante Meuleman <meuleman@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Sun, 7 Jun 2015 13:33:36 +0000 (22:33 +0900)]
rtlwifi: rtl8192c: Add init codes for "fw_version" and "fw_subversion".
The variable "fw_version" is used in the _ResetDigitalProcedure1().
but It is not initialized. so I add init codes for "fw_version" and
"fw_subversion".
Signed-off-by: Taehee Yoo <ap420073@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Sat, 6 Jun 2015 10:57:14 +0000 (19:57 +0900)]
rtlwifi: rtl8192cu: remove duplicated routine in _rtl92c_phy_rf6052_config_parafile
in the _rtl92c_phy_rf6052_config_parafile(), cases
RF90_PATH_A and RF90_PATH_B call the same routine.
so i remove one of these routine. also the return
routine is duplicated. so i remove it.
Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hans Ulli Kroll [Sun, 7 Jun 2015 11:19:16 +0000 (13:19 +0200)]
rtlwifi: fix tm_trigger usage
While working on getting my rtl8821au driver in pretty shape for
inclusion, it is dicosvered that the tm_trigger flag is used only for
the first device using this driver.
This flag handles the thermal power management in the hardware.
To change this add a entry in sttruct rtl_dm, so each device can handle
is separately.
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
_InitBeaconParameters() and rtl92cu_init_beacon_parameters() is
same routine. I remove both functions. then i add
_rtl92cu_init_beacon_parameters() in the hw.c.
_rtl92cu_init_beacon_parameters() is same routine with
_InitBeaconParameters().
Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Need to reorder init sequence to run wil_platform_init
before pci_enable_device. Assumption is platform init
may be required before device may be enabled.
Another issue, platform uninit should be called after
pci_disable_device because platform uninit may render
pci device non-accessible.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Hamad Kadmany [Tue, 9 Jun 2015 11:11:18 +0000 (14:11 +0300)]
wil6210: Support hidden SSID
Pass hidden SSID information to FW for proper operation.
In order to be able to scan/connect to the hidden SSID, SSID
setting is added when scan is requested from FW. SSID
scanning currently supports single SSID due to FW limitation.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com> Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Brent Taylor [Tue, 9 Jun 2015 11:11:19 +0000 (14:11 +0300)]
ath6kl: Fix multiple clients associating in AP mode
When one client is associated and connected to an ar6003 hw version
2.0 with firmware 3.1.1.149, and another client tries to connect, the
first client's MAC address is lost in the station list because the
"aid" is always "1". The structure "wmi_connect_event" has the "aid"
as the second byte in the message, but it should be the first byte.
This patch has been tested with linux-3.10.40
Signed-off-by: Brent Taylor <motobud@gmail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Wed, 3 Jun 2015 10:16:56 +0000 (12:16 +0200)]
ath10k: fix channel switching
In the midst of chanctx patch review channel
switching became broken which I failed to notice
until now.
Function ath10k_mac_vif_chan() reports current
chandef which isn't updated until after
switch_vif_chanctx() is returned from.
Consequently the driver just restarted operation
on channels it was residing already instead of
switching to the new ones.
Fixes: 500ff9f9389d ("ath10k: implement chanctx API") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Wed, 3 Jun 2015 10:16:55 +0000 (12:16 +0200)]
ath10k: remove ath10k_chanctx struct
In practice there's no point in having a copy of
chanctx_conf.
Most of the time the channel pointer (and band
along with it) is accessed and this can't change
after a chanctx is created because switching is
done using explicit chanctx swapping via
switch_vif_chanctx().
The only thing that can change within a
chanctx_conf and is used by the driver is
radar_enabled and channel width. These are however
always accessed in adequate mac80211 callback
context which guarantees safe access to the
chanctx data.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Michal Kazior [Wed, 3 Jun 2015 10:16:54 +0000 (12:16 +0200)]
ath10k: fix ar->rx_channel updating logic
Channel contexts aren't iterable until after
they've been added to the driver. The code assumed
otherwise.
This problem could result in:
* rx_channel being NULL and forcing Rx path to go
the slow way to get channel on QCA988X,
* report incorrect channel when running
multi-channel on QCA61X4 hw2.1,
* report incorrect channel after AP channel
switch.
Fixes: 500ff9f9389d ("ath10k: implement chanctx API") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Tue, 2 Jun 2015 07:34:15 +0000 (13:04 +0530)]
ath10k: remove unused variable 'id' in ath10k_pci_tx_pipe_cleanup()
mete_data is extracted from ce descriptor and stored in variable 'id'.
later, id is not used anywhere in the same function.
Fixes: d84a512dca23 ("ath10k: remove transfer_id from ath10k_hif_cb::tx_completion") Signed-off-by: Raja Mani <rmani@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Raja Mani [Mon, 1 Jun 2015 09:23:33 +0000 (14:53 +0530)]
ath10k: free wmi mgmt event skb when parsing fails
When wmi mgmt event function fails to parse given skb,
it should be freed on failure condition to avoid memory
leaks. Found this during the code review.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rafał Miłecki [Sun, 7 Jun 2015 11:15:31 +0000 (13:15 +0200)]
bcma: lower dependency of BCMA_DRIVER_PCI_HOSTMODE
This extension of BCMA_DRIVER_PCI has no reason to depend on
BCMA_HOST_PCI. User may just want to have PCI device attached to SoC
registered without enabling any extra client mode code.
This can be useful when having non-bcma PCI device attached or when
using other PCI driver.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Sat, 6 Jun 2015 20:45:59 +0000 (22:45 +0200)]
b43: fix support for 14e4:4321 PCI dev with BCM4321 chipset
It seems Broadcom released two devices with conflicting device id. There
are for sure 14e4:4321 PCI devices with BCM4321 (N-PHY) chipset, they
can be found in routers, e.g. Netgear WNR834Bv2. However, according to
Broadcom public sources 0x4321 is also used for 5 GHz BCM4306 (G-PHY).
It's unsure if they meant PCI device id, or "virtual" id (from SPROM).
To distinguish these devices lets check PHY type (G vs. N).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Cc: <stable@vger.kernel.org> # 3.16+ Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Thu, 4 Jun 2015 20:11:07 +0000 (22:11 +0200)]
brcmfmac: use direct data pointer in NVRAM parser struct
As we plan to add support for platform NVRAM we should store direct
data pointer without the extra struct firmware layer. This will allow
us to support other sources with the only requirement being u8 buffer.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rafał Miłecki [Thu, 28 May 2015 12:19:21 +0000 (14:19 +0200)]
brcmfmac: support NVRAMs containing pci devpaths (instead of pcie)
Recently Broadcom added support for NVRAMs with entries for multiple
PCIe devices. One of the supported formats is based on prefixes defined
like: devpath0=pcie/1/4/ and entries like 0:foo=bar 0:baz=qux etc.
Unfortunately there are also a bit older devices using different way of
defining prefixes, e.g. SmartRG SR400ac (2 x BCM43602) with entries:
devpath0=pci/1/1/
devpath1=pci/2/1
Broadcom stated this old format will never be used/supported by brcmfmac
but given the simplicity of this patch I'll insist on supporting it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Thu, 4 Jun 2015 19:31:54 +0000 (01:01 +0530)]
mwifiex: update current config_band info in start_ap
It was observed that AP beacons would not reflect correct regulatory
information upon starting AP in A band. This was because of missing
AP config band update in set_channel of start_ap.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Zhaoyang Liu [Thu, 4 Jun 2015 19:31:53 +0000 (01:01 +0530)]
mwifiex: change debug dump issue since skb maybe null
This patch fixes semantic warning for debugging data dump feature.
Previous code is based on the assumption that skb is not null.
New change makes sure that we already have data buffer.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Zhaoyang Liu <liuzy@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Taehee Yoo [Thu, 4 Jun 2015 00:47:42 +0000 (09:47 +0900)]
rtlwifi: rtl8192cu: Fix performance issue.
After physical reconnect, the rtl8192cu chipset shows low
transmission rates.It cause is that variable "iqk_initialized"
do not de-initialized. So I add this code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:47 +0000 (16:59 +0530)]
mwifiex: do not decrease tx_pending for AMSDU packet once more
Negative adapter->tx_pending is observed while running data traffic,
because tx_pending is decreased once more for AMSDU packet.
since tx_pending have been decreased for all the source MSDU packets,
we don't need to update once more for AMSDU packet.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:46 +0000 (16:59 +0530)]
mwifiex: using right tid for addressing ra_list
This patch fixes issue with the accessing correct ra_list by
downgrading corresponding tid number.
Alternatively, ra lists are created in mwifiex_wmm_add_buf_txqueue
using downgraded tid number.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:43 +0000 (16:59 +0530)]
mwifiex: drop block-ack action frames
We often see ADDBA request packets coming to driver because driver
has registered for action frame subtype. We dont process BA action
frames in host; drop such frames.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Xinmin Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avinash Patil [Wed, 3 Jun 2015 11:29:42 +0000 (16:59 +0530)]
mwifiex: support downloading IEs from tail
Earlier only RSN, WPA and channel switch IEs from tail buffer would
be downloaded to FW.
This patch adds support for downloading more IEs from tail buffer.
Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:40 +0000 (16:59 +0530)]
mwifiex: dump station support in uap mode
This patch extend cfg80211 dump_station handler, support for
dump stations associated to mwifiex micro AP.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:39 +0000 (16:59 +0530)]
mwifiex: add sta_list firmware command
This patch add sta_list firmware command, which can be used
to get power status and rssi for the stations associated to
mwifiex micro AP.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:38 +0000 (16:59 +0530)]
mwifiex: maintain station statistic in uap mode
This patch maintain statistic information for the stations associated
to the mwifiex micro AP, include tx/rx bytes/packets, signal strength,
tx bitrate.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xinming Hu [Wed, 3 Jun 2015 11:29:37 +0000 (16:59 +0530)]
mwifiex: add cfg80211 get_channel handler
This patch add cfg80211 get_channel handler for mwifiex.
The handler will be used to report current channel to upper
layer utility.
Signed-off-by: Xinming Hu <huxm@marvell.com> Signed-off-by: Cathy Luo <cluo@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Felix Fietkau [Tue, 2 Jun 2015 08:38:32 +0000 (10:38 +0200)]
ath9k: fix DMA stop sequence for AR9003+
AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wei Liu [Wed, 3 Jun 2015 10:10:42 +0000 (11:10 +0100)]
tcp: double default TSQ output bytes limit
Xen virtual network driver has higher latency than a physical NIC.
Having only 128K as limit for TSQ introduced 30% regression in guest
throughput.
This patch raises the limit to 256K. This reduces the regression to 8%.
This buys us more time to work out a proper solution in the long run.
Signed-off-by: Wei Liu <wei.liu2@citrix.com> Cc: David Miller <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 4 Jun 2015 06:49:21 +0000 (23:49 -0700)]
tcp: remove redundant checks
tcp_v4_rcv() checks the following before calling tcp_v4_do_rcv():
if (th->doff < sizeof(struct tcphdr) / 4)
goto bad_packet;
if (!pskb_may_pull(skb, th->doff * 4))
goto discard_it;
So following check in tcp_v4_do_rcv() is redundant
and "goto csum_err;" is wrong anyway.
if (skb->len < tcp_hdrlen(skb) || ...)
goto csum_err;
A second check can be removed after no_tcp_socket label for same reason.
Same tests can be removed in tcp_v6_do_rcv()
Note : short tcp frames are not properly accounted in tcpInErrs MIB,
because pskb_may_pull() failure simply drops incoming skb, we might
fix this in a separate patch.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman [Thu, 4 Jun 2015 03:43:43 +0000 (20:43 -0700)]
switchdev: documentation: use switchdev_port_obj_xxx for IPv4 FIB add/modify/delete ops
Clarify in documentation and code that IPV4 FIB add operation is used for
both adding a new FIB entry to the device and for modifying an existing FIB
entry on the device.
Also, remove left-over references to ipv4_fib ops and replace with details
on SWITCHDEV_PORT_IPV4_FIB object.
Signed-off-by: Scott Feldman <sfeldma@gmail.com> Acked-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 06:44:57 +0000 (23:44 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2015-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
new driver mt7601u for MediaTek Wi-Fi devices MT7601U
ath10k:
* qca6174 power consumption improvements, enable ASPM etc (Michal)
wil6210:
* support Wi-Fi Simple Configuration in STA mode
iwlwifi:
* a few fixes (re-enablement of interrupts for certain new
platforms that have special power states)
* Rework completely the RBD allocation model towards new
multi RX hardware.
* cleanups
* scan reworks continuation (Luca)
mwifiex:
* improve firmware debug functionality
rtlwifi:
* update regulatory database
brcmfmac:
* cleanup and new feature support in PCIe code
* alternative nvram loading for router support
====================
Conflicts:
drivers/net/wireless/iwlwifi/Kconfig
Trivial conflict in iwlwifi Kconfig, two commits adding
the same two chip numbers to the help text, but order
transposed.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 4 Jun 2015 06:40:20 +0000 (23:40 -0700)]
Merge branch 'cxgb4-next'
Hariprasad Shenai says:
====================
cxgb4: Adds support for various ethtool stats
This patch series adds the following:
Adds support to dump adapter specific stats in ethtool
Adds support to dump channel stats in ethtool
Adds support to dump loopback port stats in ethtool
Remove wake-on-lan get/set ethtool support
This patch series has been created against net-next tree and includes
patches on cxgb4 driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log