Ben Skeggs [Sun, 5 Feb 2012 23:58:09 +0000 (09:58 +1000)]
drm/nva3/pm: another few magic regs, and slightly better 0x004018 handling
Not entirely convinced 0x004018 transitions are correct yet, but, it's
an improvement.
The 750MHz value comes from fiddling with the binary driver + coolbits on
two different DDR3 NVA8 chipsets (T510 NVS3100M, and NVS300), not a clue
where this number comes from.
Ben Skeggs [Thu, 2 Feb 2012 01:43:31 +0000 (11:43 +1000)]
drm/nva3/pm: begin to restructure memory clock changes + another magic
The binary driver appears to do various bits and pieces of the memory
clock frequency change at different times, depending on the particular
transition that's occuring. I've attempted to replicate this here
for div->pll, pll->div and div->div transitions.
With some additional (patches upcoming) magic regs being bashed, this
allows me to correctly transition between all 3 perflvls on NVS300.
pll->pll transitions will *not* work correctly at the moment, pending
me tricking the binary driver into doing one and seeing how to correctly
handle it.
This patch also handles (hopefully) 0x1110e0, which appears to need
changing depending on whether in PLL or divider mode.. Maybe. We'll
see.
Dave Airlie [Wed, 23 May 2012 09:46:24 +0000 (10:46 +0100)]
Merge branch 'prime-merge' of ssh://people.freedesktop.org/~airlied/linux into drm-core-next
* 'prime-merge' of ssh://people.freedesktop.org/~airlied/linux:
drm/radeon: add PRIME support (v2)
i915: add dmabuf/prime buffer sharing support.
nouveau: add PRIME support
ttm: add prime sharing support to TTM (v2)
udl: add prime fd->handle support.
drm/prime: add exported buffers to current fprivs imported buffer list (v2)
drm/prime: introduce sg->pages/addr arrays helper
Daniel Vetter [Thu, 10 May 2012 13:25:09 +0000 (15:25 +0200)]
i915: add dmabuf/prime buffer sharing support.
This adds handle->fd and fd->handle support to i915, this is to allow
for offloading of rendering in one direction and outputs in the other.
v2 from Daniel Vetter:
- fixup conflicts with the prepare/finish gtt prep work.
- implement ppgtt binding support.
Note that we have squat i-g-t testcoverage for any of the lifetime and
access rules dma_buf/prime support brings along. And there are quite a
few intricate situations here.
Also note that the integration with the existing code is a bit
hackish, especially around get_gtt_pages and put_gtt_pages. It imo
would be easier with the prep code from Chris Wilson's unbound series,
but that is for 3.6.
Also note that I didn't bother to put the new prepare/finish gtt hooks
to good use by moving the dma_buf_map/unmap_attachment calls in there
(like we've originally planned for).
Last but not least this patch is only compile-tested, but I've changed
very little compared to Dave Airlie's version. So there's a decent
chance v2 on drm-next works as well as v1 on 3.4-rc.
v3: Right when I've hit sent I've noticed that I've screwed up one
obj->sg_list (for dmar support) and obj->sg_table (for prime support)
disdinction. We should be able to merge these 2 paths, but that's
material for another patch.
v4: fix the error reporting bugs pointed out by ickle.
v5: fix another error, and stop non-gtt mmaps on shared objects
stop pread/pwrite on imported objects, add fake kmap
Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dave Airlie [Sun, 20 May 2012 16:31:16 +0000 (17:31 +0100)]
drm/prime: add exported buffers to current fprivs imported buffer list (v2)
If userspace attempts to import a buffer it exported on the same device,
we need to return the same GEM handle for it, not a new handle pointing
at the same GEM object.
v2: move removals into a single fn, no need to set to NULL. (Chris Wilson)
Rob Clark [Thu, 17 May 2012 08:23:26 +0000 (02:23 -0600)]
drm: add bitmask property type
A bitmask property is similar to an enum. The enum value is a bit
position (0-63), and valid property values consist of a mask of
zero or more of (1 << enum_val[n]).
[airlied: 1LL -> 1ULL]
Signed-off-by: Rob Clark <rob@ti.com> Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 22 May 2012 09:39:57 +0000 (10:39 +0100)]
Merge branch 'exynos-drm-next' of git://git.infradead.org/users/kmpark/linux-samsung into drm-core-next
* 'exynos-drm-next' of git://git.infradead.org/users/kmpark/linux-samsung:
drm/exynos: add G2D driver
drm/exynos: added vp scaling feature for hdmi
drm/exynos: added source size to overlay structure
drm/exynos: add additional display mode for hdmi
drm/exynos: enable dvi mode for dvi monitor
drm/exynos: fixed wrong pageflip finish event for interlace mode
drm/exynos: add PM functions for hdmi and mixer
drm/exynos: add dpms for hdmi
drm/exynos: use threaded irq for hdmi hotplug
drm/exynos: use platform_get_irq_byname for hdmi
drm/exynos: cleanup for hdmi platform data
drm/exynos: added a feature to get gem buffer information.
drm/exynos: added drm prime feature.
drm/exynos: added cache attribute support for gem.
vgaarb: Provide dummy default device functions
Laurent Pinchart [Thu, 17 May 2012 11:27:24 +0000 (13:27 +0200)]
drm: Make the CRTC gamma_set operation optional
Drivers for hardware without gamma support should not be forced to
implement a no-op gamma set operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Rob Clark <rob.clark@linaro.org> Signed-off-by: Dave Airlie <airlied@redhat.com>
Laurent Pinchart [Thu, 17 May 2012 11:27:23 +0000 (13:27 +0200)]
drm: Constify drm_mode_config_funcs pointer
The DRM mode config functions structure declared by drivers and pointed
to by the drm_mode_config funcs field is never modified. Make it a const
pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Inki Dae <inki.dae@samsung.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: Thomas Hellstrom <thellstrom@vmware.com> Cc: Rob Clark <rob.clark@linaro.org> Reviwed-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Laurent Pinchart [Thu, 17 May 2012 11:27:22 +0000 (13:27 +0200)]
drm: Constify gem_vm_ops pointer
The GEM vm operations structure is passed to the VM core that stores it
in a const field. There vm operations structures can thus be const in
DRM as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Inki Dae <inki.dae@samsung.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Rob Clark <rob.clark@linaro.org> Reviewed-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Laurent Pinchart [Thu, 17 May 2012 11:27:19 +0000 (13:27 +0200)]
drm: Delete the vblank timer synchronously at cleanup time
A race condition exists in drm_vblank_cleanup() if the vblank disable
timer callback runs after freeing the memory that its callback function
tries to access. Fix this by deleting the timer synchronously.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Adam Jackson [Mon, 14 May 2012 20:05:48 +0000 (16:05 -0400)]
drm/radeon/dp: Probe branch/sink OUIs
Signed-off-by: Adam Jackson <ajax@redhat.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Adam Jackson [Mon, 14 May 2012 20:05:46 +0000 (16:05 -0400)]
drm/dp: Add DPCD defines for register 0x007
Low four bits are downstream port count. High bit indicates peer OUI
support. OUI matching will allow us to do additional per-sink handling
for things like DP->VGA bandwidth limits or (hopefully) the iMac-as-
display hack.
Signed-off-by: Adam Jackson <ajax@redhat.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Adam Jackson [Mon, 14 May 2012 20:05:45 +0000 (16:05 -0400)]
drm/dp: Add DPCD OUI register defines
DisplayPort has an escape hatch by which sources and sinks can identify
each other. We would prefer not to notice this, but I suspect we're
going to need to.
Signed-off-by: Adam Jackson <ajax@redhat.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Patrik Jakobsson [Mon, 21 May 2012 14:27:30 +0000 (15:27 +0100)]
gma500: handle poulsbo cursor restriction
Poulsbo needs a physical address in the cursor base register. We allocate a
stolen memory buffer and copy the cursor image provided by userspace into it.
When/If we get our own userspace driver we can map this stolen memory directly.
The patch also adds a mark in chip ops so we can identify devices that has this
requirement.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Alan Cox [Mon, 21 May 2012 14:27:10 +0000 (15:27 +0100)]
gma500: Prevent endless loop in panel power up sequence
Some devices don't have a panel connected to LVDS and thus will never power up.
This patch checks the power sequence progress bits in PP_STATUS to prevent an
endless loop on such devices.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Mon, 21 May 2012 07:09:06 +0000 (08:09 +0100)]
Merge tag 'drm-intel-next-2012-05-20' of git://people.freedesktop.org/~danvet/drm-intel into drm-core-next
Daniel wrote:
The last pull I'd like to squeeze into 3.5, safe for the hsw stuff mostly
bugfixes:
- last few patches for basic hsw enabling (Eugeni, infoframe support by
Paulo)
- Fix up infoframe support, we've hopefully squashed all the cargo-culting
in there (Paulo). Among all the issues, this finally fixes some of the
infoframe regressions seen on g4x and snb systems.
- Fixup sdvo infoframe support, this fixes a regression from 2.6.37.
- Correctly enable semaphores on snb, we've enabled it already for 3.5,
but the dmar check was slightly wrong.
- gen6 irq fixlets from Chris.
- disable gmbus on i830, the hw seems to be simply broken.
- fix up the pch pll fallout (Chris & me).
- for_each_ring macro from Chris - I've figured I'll merge this now to
avoid backport pain.
- complain when the rps state isn't what we expect (Chris). Note that this
is shockingly easy to hit and hence pretty much will cause a regression
report. But it only tells us that the gpu turbo state got out of whack,
a problem we know off since a long time (it cause the gpu to get stuck a
a fixed frequency, usually the lowest one). Chris is working on a fix,
but we haven't yet found a magic formula that works perfectly (only
patches that massively reduce the frequency of this happening).
- MAINTAINERS patch, I'm now officially the guy to beat up."
* tag 'drm-intel-next-2012-05-20' of git://people.freedesktop.org/~danvet/drm-intel: (57 commits)
drm/i915: IBX has a fixed pch pll to pch pipe mapping
drm/i915: implement hsw_write_infoframe
drm/i915: small hdmi coding style cleanups
drm/i915: fixup infoframe support for sdvo
drm/i915: Enable the PCH PLL for all generations after link training
drm/i915: Convert BUG_ON(!pll->active) and friends to a WARN
drm/i915: don't clobber the pipe param in sanitize_modesetting
drm/i915: disable gmbus on i830
drm/i915: Replace the feature tests for BLT/BSD with ring init checks
drm/i915: Check whether the ring is initialised prior to dispatch
drm/i915: Introduce for_each_ring() macro
drm/i915: Assert that the transcoder is indeed off before modifying it
drm/i915: hook Haswell devices in place
drm/i915: prepare HDMI link for Haswell
drm/i915: move HDMI structs to shared location
drm/i915: add WR PLL programming table
drm/i915: add support for DDI-controlled digital outputs
drm/i915: detect digital outputs on Haswell
drm/i915: program iCLKIP on Lynx Point
drm/i915: program WM_LINETIME on Haswell
...
v2: Add a DRM_DEBUG_KMS message to explain why a given pll was
selected, suggested by Chris Wilson.
v3: Actually run git add.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49712 Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Paulo Zanoni [Mon, 14 May 2012 20:12:50 +0000 (17:12 -0300)]
drm/i915: small hdmi coding style cleanups
- Changed the coding style of auxiliary infoframe functions to make
them smaller
- Fixed the column alignment of some function definitions
- Remove definition of "struct drm_crtc" in some places as they're
used only to retrieve "struct intel_crtc"
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sat, 12 May 2012 18:22:00 +0000 (20:22 +0200)]
drm/i915: fixup infoframe support for sdvo
At least the worst offenders:
- SDVO specifies that the encoder should compute the ecc. Testing also
shows that we must not send the ecc field, so copy the dip_infoframe
struct to a temporay place and avoid the ecc field. This way the avi
infoframe is exactly 17 bytes long, which agrees with what the spec
mandates as a minimal storage capacity (with the ecc field it would
be 18 bytes).
- Only 17 when sending the avi infoframe. The SDVO spec explicitly
says that sending more data than what the device announces results
in undefined behaviour.
- Add __attribute__((packed)) to the avi and spd infoframes, for
otherwise they're wrongly aligned. Noticed because the avi infoframe
ended up being 18 bytes large instead of 17. We haven't noticed this
yet because we don't use the uint16_t fields yet (which are the only
ones that would be wrongly aligned).
Chris Wilson [Sun, 13 May 2012 08:54:09 +0000 (09:54 +0100)]
drm/i915: Enable the PCH PLL for all generations after link training
Hidden away within one chipset specific path was the necessary logic to
turn on the PLL. This needs to be done everywhere in order for us to
drive any display! As such as soon as we tested on a non-CougarPoint
chipset, we failed to bring up any DisplayPorts and generated a nice set
of assertion failures in the process. At least one part of our logic is
working, the part that assumes that we have no idea what we are doing.
Reported-by: guang.a.yang@intel.com
References: https://bugs.freedesktop.org/show_bug.cgi?id=49712 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Sun, 13 May 2012 19:16:12 +0000 (20:16 +0100)]
drm/i915: Convert BUG_ON(!pll->active) and friends to a WARN
Turn a fatal lockup into a merely blank display with lots of shouty
messages.
v2: Whilst in the area, convert the other BUG_ON into less fatal errors.
In particular, note that we may be called on a PCH platform not using
PLLs, such as Haswell, and so we do not always want to BUG_ON(!pll)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: Sanitize BIOS debugging bits from PIPECONF
Spotted by staring at debug output of an (as it turns out) totally
unrelated bug.
v2: I've totally failed to do the s/pipe/i/ correctly, spotted by
Chris Wilson.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Cc: stable@kernel.org (the regression was Cc: stable, too) Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel Vetter [Sun, 13 May 2012 12:44:20 +0000 (14:44 +0200)]
drm/i915: disable gmbus on i830
The hw just returns garbage.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49838 Reported-and-tested-by: Vladyslav <DFEW.Entwickler@googlemail.com> Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 11 May 2012 13:29:31 +0000 (14:29 +0100)]
drm/i915: Check whether the ring is initialised prior to dispatch
Rather than use the magic feature tests HAS_BLT/HAS_BSD just check
whether the ring we are about to dispatch the execbuffer on is
initialised.
v2: Use intel_ring_initialized()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson [Fri, 11 May 2012 13:29:30 +0000 (14:29 +0100)]
drm/i915: Introduce for_each_ring() macro
In many places we wish to iterate over the rings associated with the
GPU, so refactor them to use a common macro.
Along the way, there are a few code removals that should be side-effect
free and some rearrangement which should only have a cosmetic impact,
such as error-state.
Note that this slightly changes the semantics in the hangcheck code:
We now always cycle through all enabled rings instead of
short-circuiting the logic.
v2: Pull in a couple of suggestions from Ben and Daniel for
intel_ring_initialized() and not removing the warning (just moving them
to a new home, closer to the error).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Added note to commit message about the small behaviour
change, suggested by Ben Widawsky.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eugeni Dodonov [Wed, 9 May 2012 18:37:31 +0000 (15:37 -0300)]
drm/i915: prepare HDMI link for Haswell
On Haswell, we need to properly train the DDI buffers prior to enabling
HDMI, and enable the required clocks with correct dividers for the desired
frequency.
Also, we cannot simple reuse HDMI routines from previous generations of
GPU, as most of HDMI-specific stuff is being done via the DDI port
programming instead of HDMI-specific registers.
This commit take advantage of the WR PLL clock table which is in a
separate (previous) commit to select the right divisors for each mode.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eugeni Dodonov [Wed, 9 May 2012 18:37:29 +0000 (15:37 -0300)]
drm/i915: add WR PLL programming table
This table is used for programming WR PLL clocks, used by HDMI and DVI outputs.
I split it into a separate patch to simplify the HDMI enabling patch which was
getting huge.
Note that this table is a temporary solution for WR PLL programming. It
will be reworked into a more exact algorithm at a later stage. But for
now, it provides the most accurate clock setting solution, so we use it
here.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eugeni Dodonov [Wed, 9 May 2012 18:37:27 +0000 (15:37 -0300)]
drm/i915: detect digital outputs on Haswell
Digital port detection on Haswell is indicated by the presence of a bit in
DDI_BUF_CTL for port A, and by a different register for ports B, C and D.
So we check for those bits during the initialization time and let the hdmi
function know about those.
Note that this bit does not indicates whether the output is DP or HDMI.
However, the DDI buffers can be programmed in a way that is shared between
DP/HDMI and FDI/HDMI except for PORT E.
So for now, we detect those digital outputs as being HDMI, but proper DP
support is still pending.
Note that DDI A can only drive eDP, so we do not handle it here for hdmi
initialization.
v2: simplify Haswell handling logic
v3: use generic function for handling digital outputs.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eugeni Dodonov [Wed, 9 May 2012 18:37:26 +0000 (15:37 -0300)]
drm/i915: program iCLKIP on Lynx Point
The iCLKIP clock is used to drive the VGA pixel clock on the PCH. In order
to do so, it must be programmed to properly do the clock ticks according
to the divisor, phase direction, phase increments and a special auxiliary
divisor for 20MHz clock.
v2: calculate divisor values directly instead of relying on a table.
v3: merged a fix from Ben to properly check for invalid divider values.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eugeni Dodonov [Wed, 9 May 2012 18:37:24 +0000 (15:37 -0300)]
drm/i915: program WM_LINETIME on Haswell
The line time can be programmed according to the number of horizontal
pixels vs effective pixel rate ratio.
v2: improve comment as per Chris Wilson suggestion
v3: incorporate latest changes in specs.
v4: move into wm update routine, also mention that the same routine can
program IPS watermarks. We do not have their enablement code yet, nor
handle the required clock settings at the moment, so this patch won't
program those values for now.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eugeni Dodonov [Wed, 9 May 2012 18:37:20 +0000 (15:37 -0300)]
drm/i915: initialize DDI buffer translations
DDI is introduced starting with Haswell GPU generation. So to simplify its
management in the future, we also add intel_ddi.c to hold all the
DDI-related items.
Buffer translations for DDI links must be initialized prior to enablement.
For FDI and DP, first 9 pairs of values are used to select the connection
parameters. HDMI uses the last pair of values and ignores the first 9
pairs. So we program HDMI values in both cases, which allows HDMI to work
over both FDI and DP-friendly buffers.
Eugeni Dodonov [Wed, 9 May 2012 18:37:19 +0000 (15:37 -0300)]
drm/i915: account for only one PCH receiver on Haswell
On Haswell, only one pipe can work in FDI mode, so this patch prevents
messing with wrong registers when FDI is being used by non-first pipe. And
to prevent this, we also specify that the VGA can only be used on pipe 0
for now in the crtc_mask value.
Eugeni Dodonov [Wed, 9 May 2012 18:37:18 +0000 (15:37 -0300)]
drm/i915: handle DDI-related assertions
Prevent bogus asserts on DDI-related paths.
Longer explanation from Eugeni by mail:
"For the asserts there are 3 paths where we hit them:
- in assert_fdi_tx (we don't have the FDI_TX_CTL anymore, backup plan
DDI_FUNC_CTL is used instead)
- in assert_fdi_tx_pll_enabled (we have the combination of iCLKIP and
DDI_FUNC_CTL, plus PORT_CLK_SEL and PIPE_CLK_SEL now to make things
work). We could use an assert here indeed - if we configure port to
use one clock, and pipe to use another, everything hangs. Right now,
we configure all of them in one place only; but yes, when DP code
lands it will get more funky.
- and in ironlake_fdi_pll_enable. I reuse part of this function (to
configure the TU sizes), but as in the 1st case, FDI_TX_CTL is gone
so I just ignore it here."
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
[danvet: Pasted Eugeni's explanation into the commit message.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eugeni Dodonov [Wed, 9 May 2012 18:37:16 +0000 (15:37 -0300)]
drm/i915: enable power wells on Haswell init
This attempts to enable all the available power wells during the
initialization.
Those power wells can be enabled in parallel or on-demand, and disabled
when no longer needed, but this is out of scope of this initial
enablement. Proper tracking of who uses which power well will require
a considerable rework of our display handling, so we just leave them all
enabled when the driver is loaded for now.
v2: use more generic and future-proof code
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eugeni Dodonov [Wed, 9 May 2012 23:30:31 +0000 (20:30 -0300)]
drm/i915: detect PCH encoders on Haswell
On Haswell, the recommended PCH-connected output is the one driven by DDI
E in FDI mode, used for VGA connection. All the others are handled by the
CPU.
Note that this does not accounts for Haswell/PPT combination yet, so if we
encounter such combination an error message is thrown to indicate that
things could go wrong.
v2: improve non-LPT detection warning per Daniel Vetter's suggestion.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eugeni Dodonov [Wed, 9 May 2012 18:37:13 +0000 (15:37 -0300)]
drm/i915: show unknown sdvox registers on hdmi init
This will throw a BUG() message when an unknown sdvox register is
given to intel_hdmi_init. When this happens, things could going to be pretty
much broken afterwards, so we better detect this as soon as possible.
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eugeni Dodonov [Wed, 9 May 2012 18:37:12 +0000 (15:37 -0300)]
drm/i915: properly check for pipe count
As suggested by Chris Wilson and Daniel Vetter, this chunk of code can be
simplified with a more simple check.
Also, as noticed by Jesse Barnes, it is worth mentioning that plane is an
enum and num_pipe is an int, so we could be more paranoid here about those
validation checks eventually.
CC: Daniel Vetter <daniel.vetter@ffwll.ch> CC: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eugeni Dodonov [Wed, 9 May 2012 18:37:11 +0000 (15:37 -0300)]
drm/i915: calculate watermarks for devices that have 3 pipes
This adds proper support for calculating those watermarks, checking for
number of available pipes instead of specific GPU variants when deciding
if watermarks for 3rd pipe are necessary.
Chris Wilson [Wed, 9 May 2012 10:56:28 +0000 (11:56 +0100)]
drm/i915: gen6_enable_rps() wants to be called after ring initialisation
Currently we call gen6_enable_rps() (which writes into the per-ring
register mmio space) from intel_modeset_init_hw() which is called before
we initialise the rings. If we defer intel_modeset_init_hw() until
afterwards (in the intel_modeset_gem_init() phase) all is well.
v2: Rectify ordering of gem vs display HW init upon resume. (Daniel)
v3: Fix up locking. (Paulo)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Smash Paulo's locking fix onto Chris' patch.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Joonyoung Shim [Thu, 17 May 2012 11:06:32 +0000 (20:06 +0900)]
drm/exynos: add G2D driver
Changelog v3:
- use __u64 instead of pointer in ioctl struct.
The G2D is a 2D graphic accelerator that supports Bit Block Transfer.
This G2D driver is exynos drm specific and supports only G2D(version
4.1) of later Exynos series from Exynos4X12 because supporting DMA.
The G2D is performed by two tasks simply.
1. Configures the rendering parameters, such as foreground color and
coordinates data by setting the drawing context registers.
2. Start the rendering process by setting thre relevant command
registers accordingly.
The G2D version 4.1 supports DMA mode as host interface. User can make
command list to reduce HOST(ARM) loads. The contents of The command list
is setted to relevant registers of G2D by DMA.
The command list is composed Header and command sets and Tail.
- Header: The number of command set(4Bytes)
- Command set: Register offset(4Bytes) + Register data(4Bytes)
- Tail: Pointer of base address of the other command list(4Bytes)
By Tail field, the G2D can process many command lists without halt at
one go.
The G2D has following the rendering pipeline.
--> Primitive Drawing --> Rotation --> Clipping --> Bilinear Sampling
--> Color Key --> ROP --> Mask Operation --> Alpha Blending -->
Dithering --> FrameBuffer
And supports various operations from the rendering pipeline.
- copy
- fast solid color fill
- window clipping
- rotation
- flip
- 4 operand raster operation(ROP4)
- masking operation
- alpha blending
- color key
- dithering
- etc
User should make the command list to data and registers needed by
operation to use. The Exynos G2D driver only manages the command lists
received from user. Some registers needs memory base address(physical
address) of image. User doesn't know its physical address, so fills the
gem handle of that memory than address to command sets, then G2D driver
converts it to memory base address.
We adds three ioctls and one event for Exynos G2D.
- ioctls
DRM_EXYNOS_G2D_GET_VER: get the G2D hardware version
DRM_EXYNOS_G2D_SET_CMDLIST: set the command list from user to driver
DRM_EXYNOS_G2D_EXEC: execute the command lists setted to driver
- event
DRM_EXYNOS_G2D_EVENT: event to give notification completion of the
command list to user
Seung-Woo Kim [Tue, 24 Apr 2012 09:52:22 +0000 (18:52 +0900)]
drm/exynos: added vp scaling feature for hdmi
This patch adds vp scaling feature for exynos hdmi. Scaling ratio
between source and destination is used for width and height.
Also meaningless variables to set registers are cleaned.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Seung-Woo Kim [Tue, 24 Apr 2012 09:43:10 +0000 (18:43 +0900)]
drm/exynos: added source size to overlay structure
Set plane has source size but exynos overlay structure did
not consider it. This patch adds source size to overlay
structure. For set crtc, source size is set from crtc size.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Seung-Woo Kim [Tue, 24 Apr 2012 08:39:15 +0000 (17:39 +0900)]
drm/exynos: enable dvi mode for dvi monitor
Hdmi monitor and dvi monitor can be distinguished with edid.
This patch enables dvi mode if dvi monitor is connected and does
not enable audio feature for dvi mode because dvi has no audio
feature.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Seung-Woo Kim [Mon, 23 Apr 2012 11:30:13 +0000 (20:30 +0900)]
drm/exynos: fixed wrong pageflip finish event for interlace mode
Pageflip finish event for interlace mode has bug on checking top
field vsync because of comparing between dma address converted
by start coordinates and non-converted dma address.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Inki Dae <inki.dae@samsung.com>
Alex Deucher [Thu, 10 May 2012 17:00:06 +0000 (13:00 -0400)]
drm/radeon: make use of radeon_gem_init() consistent
All radeon_gem_init() does is initialize the gem objects
list. radeon_device.c does this explicitly. r600+ calls
radeon_gem_init() so the list gets initialized twice. Older
asics don't call it at all and rely on the the init in
radeon_device.c. Just call radeon_gem_init() in radeon_device.c
and remove the explicit calls from all the newer asics.
All asics call radeon_gem_fini() in their fini pathes. That
could possibly be cleaned up too.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
connector_names table is just a repeat of information that
already exists in drm_connector_enum_list and the same string
can be retrieved using drm_get_connector_name function.
Nuke the redundant table and use the proper function to retrieve
the connector name.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Michel Dänzer [Tue, 15 May 2012 15:31:02 +0000 (17:31 +0200)]
drm/radeon: Also reset BCI on SI GPU reset.
Without this, e.g. egltri_screen looks scrambled after a GPU reset.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Fri, 4 May 2012 15:06:22 +0000 (11:06 -0400)]
drm/radeon: don't mess with hot plug detect for eDP or LVDS connector v2
It seems imac pannel doesn't like whe we change the hot plug setup
and then refuse to work. This help but doesn't fully fix:
https://bugzilla.redhat.com/show_bug.cgi?id=726143
v2: fix typo and improve commit message
Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 17 May 2012 10:17:33 +0000 (11:17 +0100)]
gma500: fix build warning
CC [M] drivers/gpu/drm/i915/i915_gem_evict.o
/ssd/git/drm-core-next/drivers/gpu/drm/gma500/psb_device.c: In function ‘psb_chip_errata’:
/ssd/git/drm-core-next/drivers/gpu/drm/gma500/psb_device.c:360:1: warning: no return statement in function returning non-void [-Wreturn-type]
/ssd/git/drm-core-next/drivers/gpu/drm/gma500/psb_device.c: At top level:
/ssd/git/drm-core-next/drivers/gpu/drm/gma500/psb_device.c:379:2: warning: initialization from incompatible pointer type [enabled by default]
/ssd/git/drm-core-next/drivers/gpu/drm/gma500/psb_device.c:379:2: warning: (near initialization for ‘psb_chip_ops.errata’) [enabled by default]
Dan Carpenter [Thu, 10 May 2012 07:33:02 +0000 (10:33 +0300)]
gma500: silence an unused variable warning
If CONFIG_BACKLIGHT_CLASS_DEVICE is disabled then GCC warns that:
drivers/gpu/drm/gma500/opregion.c:154:6: warning:
unused variable ‘max’ [-Wunused-variable]
Which give me a chance to use the new config_enabled() macro. :)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Paul Menzel <paulepanter@users.sourceforge.net> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
projects / linux-beck.git / log