Carlo Caione [Tue, 1 Mar 2016 22:04:34 +0000 (23:04 +0100)]
pinctrl: amlogic: Make driver independent from two-domain configuration
In the Amlogic Meson8 / Meson8b platforms we have two different buses:
cbus and aobus, corresponding to 2 different power domains (regular and
always-on). On each bus a different set of registers is mapped to manage
muxes, GPIOs and in general to control a clear subset of the pins.
Considering this architecture, having two different pinctrl devices, one
for each bus / power domain, makes much more sense than just having one
single device.
Right now we have one single pin controller driver that uses two
different domains (represented by 'gpio' and 'gpio-ao' sub-nodes in the
DTS) to manage the set of registers on the two buses. This dual-domain
configuration is hardcoded into the driver that strictly requires one
domain for each bus in the same pin controller device.
With this patch we refactor the driver to allow splitting the driver in
two parts. This change is needed to have a proper description of the HW
in the device-tree where we want to introduce aobus and cbus.
Signed-off-by: Carlo Caione <carlo@endlessm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Arnd Bergmann [Wed, 2 Mar 2016 15:58:53 +0000 (16:58 +0100)]
pinctrl: at91: use __maybe_unused to hide pm functions
The at91-pio4 pinctrl driver uses SET_SYSTEM_SLEEP_PM_OPS() to
conditionally set the correct suspend/resume options, but they
become unused when CONFIG_PM is disabled:
drivers/pinctrl/pinctrl-at91-pio4.c:827:12: error: 'atmel_pctrl_suspend' defined but not used [-Werror=unused-function]
drivers/pinctrl/pinctrl-at91-pio4.c:847:12: error: 'atmel_pctrl_resume' defined but not used [-Werror=unused-function]
This adds __maybe_unused annotations so the compiler knows
it can silently drop them instead of warning.
Wolfram Sang [Tue, 1 Mar 2016 16:38:46 +0000 (17:38 +0100)]
pinctrl: sh-pfc: core: don't open code of_device_get_match_data()
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Masahiro Yamada [Wed, 2 Mar 2016 06:14:40 +0000 (15:14 +0900)]
pinctrl: uniphier: rename CONFIG options and file names
The current "CONFIG_PINCTRL_UNIPHIER_PH1_*" is too long. It would
not hurt to drop "PH1_" because "UNIPHIER_" already well specifies
the SoC family. Also, rename files for consistency.
...meaning that it is currently not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: linux-gpio@vger.kernel.org Cc: linux-mediatek@lists.infradead.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Paul Gortmaker [Mon, 29 Feb 2016 20:48:37 +0000 (15:48 -0500)]
pinctrl: sunxi: does not need module.h
This file is not modular, nor is it using modular functions. The
only thing close is the global THIS_MODULE which comes from export.h
so lets replace it appropriately and cut back on the amount of
header stuff we draw in by several thousand lines.
Cc: linux-gpio@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Henry Paulissen [Sun, 28 Feb 2016 23:13:27 +0000 (00:13 +0100)]
pinctrl: sunxi: Change mux setting on PI irq pins
While I was testing irq's on the cubietruck I found a couple of
not working irq pins. Further diving into the problem it opened
up a mess called "manual".
This so called manual (A20 user manual v1.3 dated 2014-10-10) says:
Pin overview:
Page 237: EINT26 is on mux 5.
Page 288: EINT26 is on mux 6.
The manual is so contradicting that further tests had to be made
to see which of the 2 statements where correct.
This patch is based on actual outcome of these tests and not what
the manual says.
Test procedure used:
Connect a 1 pulse per second (GPS) line to the pin.
Check /proc/interrupts if a irq was attached and if irq's where
received.
Hardware used:
Henry Paulissen: Cubietruck
Andere Przywara: BananaPi M1
Tested-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Henry Paulissen <henry@nitronetworks.nl> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Henry Paulissen [Sun, 28 Feb 2016 23:13:26 +0000 (00:13 +0100)]
pinctrl: sunxi: Remove non existing irq's
While I was testing irq's on the cubietruck I found a couple of
not working irq pins. Further diving into the problem it opened
up a mess called "manual".
This so called manual (A20 user manual v1.3 dated 2014-10-10) says:
Pin overview:
Page 233: EINT12 is on pin PC19 mux6.
Page 236: EINT12 is on pin PH12 mux6.
Now, it is a bit strange to have the same IRQ on 2 different pins,
but I guess this could still be possible hardware wise. But then:
Pin registers:
Page 253: EINT12 is *not* on pin PC19.
Page 281: EINT12 is on pin PH12.
The manual is so contradicting that further tests had to be made
to see which of the 2 statements where correct.
This patch is based on actual outcome of these tests and not what
the manual says.
Test procedure used:
Connect a 1 pulse per second (GPS) line to the pin.
Philipp Zabel [Thu, 25 Feb 2016 17:23:07 +0000 (18:23 +0100)]
pinctrl: imx: attach iomuxc device to gpr syscon
Commit bdb0066df96e ("mfd: syscon: Decouple syscon interface from platform
devices") added the possibility to register syscon devices without
associated platform device. This also removed regmap debugfs facilities,
which don't work without a device. This patch associates the syscon regmap
that handles the IOMUX controller's general purpose registers with the
pinctrl device so that the GPR registers appear in the regmap debugfs
directory again. For example, on i.MX6Q the GPR registers now can be
read from /sys/kernel/debug/regmap/20e0000.iomuxc-gpr/registers.
Phil Elwell [Tue, 1 Mar 2016 01:30:08 +0000 (17:30 -0800)]
pinctrl-bcm2835: Fix cut-and-paste error in "pull" parsing
The DT bindings for pinctrl-bcm2835 allow both the function and pull
to contain either one entry or one per pin. However, an error in the
DT parsing can cause failures if the number of pulls differs from the
number of functions.
Cc: stable@vger.kernel.org Signed-off-by: Eric Anholt <eric@anholt.net> Signed-off-by: Phil Elwell <phil@raspberrypi.org> Reviewed-by: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for setting up GPIO pin interrupts in the lpc18xx pinctrl
driver. The LPC18xx SCU contain two registers that sets up the signal
routing to the GPIO pin interrupt (PINT) block. The routing uses the
GPIO namespace and not the pin namespace so a lookup is preformed on
the pin.
Routing configuration is done in the device tree by using the new
nxp,gpio-pin-interrupt property. This property takes single parameter
which sets the PINT hwirq for the GPIO.
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Joachim Eastwood [Thu, 25 Feb 2016 21:44:37 +0000 (22:44 +0100)]
pinctrl: core: create nolock version of pinctrl_find_gpio_range_from_pin
pinctrl_find_gpio_range_from_pin takes the pctldev->mutex but so
does pinconf_pins_show and this will cause a deadlock if
pinctrl_find_gpio_range_from_pin is used in .pin_config_get
callback.
Create a nolock version of pinctrl_find_gpio_range_from_pin to
allow pin to gpio lookup to be used from pinconf_pins_show.
Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Colin Ian King [Wed, 24 Feb 2016 17:32:50 +0000 (17:32 +0000)]
pinctrl: lpc18xx: ensure ngroups is initialized at correct place
The initialization of ngroups is occurring at the end of the
first iteration of the outer loop, which means that the
assignment pins[ngroups++] = i is potentially indexing into
a region outside of array pins because ngroups is not initialized.
Instead, initialize ngroups in the inner loop before the first
inner loop iteration.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simon Horman [Thu, 25 Feb 2016 00:51:54 +0000 (09:51 +0900)]
pinctrl: sh-pfc: Use ARCH_RENESAS
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
allwinner,sun8i-h3-r-pinctrl was added by
commit ba83a11104ae ("pinctrl: sunxi: Add H3 R_PIO controller support")
but the patch was missing proper binding documentation. This patch fixes
this issue.
Biao Huang [Tue, 16 Feb 2016 19:16:34 +0000 (03:16 +0800)]
pinctrl: mediatek: add input-enable and direction setting for eint resources
To use pin as eint, user should make sure that:
1. pin is set to right mode, this is done in .irq_request_resources
implementation already.
2. direction of the pin is input, which should call GPIO API to set
pin to input gpio.
We add what step 2 do to .irq_request_resources so that user doesn't
need call GPIO API any more when pin for eint usage.
Magnus Damm [Wed, 17 Feb 2016 08:15:49 +0000 (17:15 +0900)]
pinctrl: sh-pfc: Rework PFC GPIO support
The sh-pfc pinctrl driver is currently handling SoC-specific
PFC hardware blocks on ARM64, ARM and SH architectures.
For older SoCs using SH cores and some 32-bit ARM SoCs the PFC
hardware also provides GPIO functionality. On the majority of
32-bit ARM SoCs from Renesas and so far all ARM64 SoCs the GPIO
feature is provided by separate hardware blocks.
So far GPIO support in the PFC driver has been compiled-in for
the majority of the SoCs, but with this patch applied the SoCs
with PFC support may select from one of the following:
- CONFIG_PINCTRL_SH_PFC - Used if PFC lacks GPIO hardware
- CONFIG_PINCTRL_SH_PFC_GPIO - Used if PFC includes GPIO support
This patch results in the following changes:
- The GPIO functionality is only compiled-in on relevant SoCs
- The number of lines of code is reduced
Build tested using the following configurations:
- r8a7795 -> CONFIG_PINCTRL_SH_PFC_GPIO=n -> OK (ARM64)
- r8a7790 -> CONFIG_PINCTRL_SH_PFC_GPIO=n -> OK (ARM)
- r8a7790 + r8a7740 -> CONFIG_PINCTRL_SH_PFC_GPIO=y -> OK (ARM)
- r8a7740 -> CONFIG_PINCTRL_SH_PFC_GPIO=y -> OK (ARM)
- sh7751 -> CONFIG_PINCTRL_SH_PFC=n -> OK (SH rts7751r2d1)
- sh7724 -> CONFIG_PINCTRL_SH_PFC_GPIO=y -> OK (SH ecovec24)
Magnus Damm [Mon, 15 Feb 2016 12:17:19 +0000 (21:17 +0900)]
pinctrl: sh-pfc: r8a7795: Add support for INTC-EX IRQ pins
Most pins on the r8a7795 SoC can be configured in GPIO mode for
interrupt and GPIO functionality, while a couple of them can also
be routed to the INTC-EX hardware block (formerly known as IRQC).
On r8a7795 the INTC-EX hardware handles pins IRQ0 -> IRQ5 and
this patch adds support for them to the PFC driver as "intc_ex_irqN".
Tested on r8a7795 Salvator-X with an external loop back adapter on
EXIO_D that connects pin 9 (IRQ2/GP2_02) and pin 26 (ExA22/GP2_06).
Signed-off-by: Magnus Damm <damm+renesas@opensource.se> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ryo Kataoka [Wed, 10 Feb 2016 22:39:46 +0000 (01:39 +0300)]
pinctrl: sh-pfc: r8a7794: Add audio clock pin groups
Add the audio clock pin groups to the R8A7794 PFC driver.
[Sergei: fixed pin group names to reflect the reality, fixed pin names in
the comments to *_pins[], lowercased the separator comment, resolved rejects,
added the changelog, renamed the patch.]
Ryo Kataoka [Wed, 10 Feb 2016 22:38:58 +0000 (01:38 +0300)]
pinctrl: sh-pfc: r8a7794: Add SSI pin groups
Add the SSI pin groups to the R8A7794 PFC driver.
[Sergei: fixed inconsistent alternate pin group naming, split SSI5/6 pin
groups into data/control ones, moved SSI7 data B group to its proper place,
fixed pin names in the comments to *_pins[], extended Cogent Embedded's
copyright, added the changelog, renamed the patch.]
Wei Yongjun [Sat, 6 Feb 2016 14:56:36 +0000 (22:56 +0800)]
pinctrl: Fix return value check in amd_gpio_probe()
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Due to a typo Zynq pin controller does not set pin function of qspi1
when using function qspi1. So pin group for qspi1 has to be renamed to
"qspi1_0_grp" as outlined in the corresponding bindings documentation.
This also removes kernel message:
zynq-pinctrl 700.pinctrl: invalid group "qspi1_0_grp" for function "qspi1"
Masahiro Yamada [Wed, 10 Feb 2016 09:54:32 +0000 (18:54 +0900)]
pinctrl: mediatek: guard sub-directory with CONFIG_PINCTRL_MTK
CONFIG_PINCTRL_MTK is more suitable than CONFIG_ARCH_MEDIATEK
to guard the drivers/pinctrl/mediatek/ directory.
(I renamed CONFIG_PINCTRL_MTK_COMMON to CONFIG_PINCTRL_MTK.)
This allows COMPILE_TEST to descend into drivers/pinctrl/mediatek
without CONFIG_ARCH_MEDIATEK define.
pinctrl: sunxi: Use pin number when calling sunxi_pmx_set
sunxi_pmx_set accepts pin number and then calculates offset by
subtracting pin_base from it. sunxi_pinctrl_gpio_get, on the other hand,
gets offset so we have to convert it to pin number so we won't get
negative value in sunxi_pmx_set.
This was only used on A10 so far, where there is only one GPIO chip with
pin_base set to 0 so it didn't matter. However H3 also requires this
workaround but have two pinmux sections, triggering problem for PL port.
Signed-off-by: Krzysztof Adamski <k@japko.eu> Acked-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Maxime Coquelin [Mon, 8 Feb 2016 17:57:39 +0000 (18:57 +0100)]
pinctrl: stm32: Fix compile testing selection
While selecting the driver for compile testing seemed possible,
the driver was not compiled because the driver directory was only
added if ARCH_STM32 was selected.
This patch now makes the pinctrl Makefile to add stm32 directory if
PINCTRL_STM32 is selected.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl: sh-pfc: Rename PINMUX_IPSR_DATA() to PINMUX_IPSR_GPSR()
This macro describes a pinmux configuration that needs configuration in
both a Peripheral Function Select Register (IPSR) and in a
GPIO/Peripheral Function Select Register 1 (GPSR). Reflect that in the
macro name for clarity.
pinctrl: pinctrl-pic32: Add PIC32 pin control driver
Add a driver for the pin controller present on the Microchip PIC32
including the specific variant PIC32MZDA. This driver provides pinmux
and pinconfig operations as well as GPIO and IRQ chips for the GPIO
banks.
Biao Huang [Wed, 3 Feb 2016 01:24:46 +0000 (09:24 +0800)]
pinctrl: mediatek: Add gpio_request_enable support
Implement the .gpio_request_enable() callbacks in struct pinmux_ops
in mediatek pinctrl driver. Make sure that when gpio_request is called,
GPIO on the pin is enabled.
Masahiro Yamada [Sat, 23 Jan 2016 15:32:09 +0000 (00:32 +0900)]
pinctrl: sunxi: guard sub-directory with CONFIG_PINCTRL_SUNXI
CONFIG_PINCTRL_SUNXI is more suitable than CONFIG_ARCH_SUNXI
to guard the drivers/pinctrl/sunxi/ directory.
(I renamed CONFIG_PINCTRL_SUNXI_COMMON to CONFIG_PINCTRL_SUNXI.)
The STn8815 has 22 dedicated pins for CLCD with up to 16 bits
in parallel, but pins 32 thru 39 can be used for an additional
CLCD signal lines 16 thru 23.
Biao Huang [Wed, 27 Jan 2016 01:24:42 +0000 (09:24 +0800)]
pinctrl: mediatek: Add Pinctrl/GPIO/EINT driver for mt2701
Add mt2701 support using mediatek common pinctrl driver.
MT2701 have some special pins need an extra setting register
than other ICs, so adding this support to common code.
Stefan Agner [Fri, 8 Jan 2016 18:50:30 +0000 (10:50 -0800)]
pinctrl: freescale: imx: implement gpio_disable_free for Vybrid
The Freescale Vybrid SoC has GPIO capabilities as part of the
IOMUXC. To enable GPIO's, the gpio_request_enable callback has
been implemented, however the corsponding gpio_disable_free
callback is missing. So far, disabling (unexporting) a GPIO left
the pin in its last state.
Implement a proper gpio_disable_free function which clears the
three enable bits which influence the state (IBE, OBE and PUE).
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
...meaning that they are currently not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
A recent commit moved these from module_init to arch_initcall already, so
the init ordering remains untouched with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: Daniel Kurtz <djkurtz@chromium.org> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: Hongzhou Yang <hongzhou.yang@mediatek.com> Cc: Yingjoe Chen <yingjoe.chen@mediatek.com> Cc: linux-gpio@vger.kernel.org Cc: linux-mediatek@lists.infradead.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds [Sun, 24 Jan 2016 20:50:56 +0000 (12:50 -0800)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.5 plus some 4.4 fixes.
The executive summary:
- ATH79 platform improvments, use DT bindings for the ATH79 USB PHY.
- Avoid useless rebuilds for zboot.
- jz4780: Add NEMC, BCH and NAND device tree nodes
- Initial support for the MicroChip's DT platform. As all the device
drivers are missing this is still of limited use.
- Some Loongson3 cleanups.
- The unavoidable whitespace polishing.
- Reduce clock skew when synchronizing the CPU cycle counters on CPU
startup.
- Add MIPS R6 fixes.
- Lots of cleanups across arch/mips as fallout from KVM.
- Lots of minor fixes and changes for IEEE 754-2008 support to the
FPU emulator / fp-assist software.
- Minor Ralink, BCM47xx and bcm963xx platform support improvments.
- Support SMP on BCM63168"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (84 commits)
MIPS: zboot: Add support for serial debug using the PROM
MIPS: zboot: Avoid useless rebuilds
MIPS: BMIPS: Enable ARCH_WANT_OPTIONAL_GPIOLIB
MIPS: bcm63xx: nvram: Remove unused bcm63xx_nvram_get_psi_size() function
MIPS: bcm963xx: Update bcm_tag field image_sequence
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
MIPS: bcm963xx: Move Broadcom BCM963xx image tag data structure
MIPS: bcm63xx: nvram: Use nvram structure definition from header file
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
MAINTAINERS: Add KVM for MIPS entry
MIPS: KVM: Add missing newline to kvm_err()
MIPS: Move KVM specific opcodes into asm/inst.h
MIPS: KVM: Use cacheops.h definitions
MIPS: Break down cacheops.h definitions
MIPS: Use EXCCODE_ constants with set_except_vector()
MIPS: Update trap codes
MIPS: Move Cause.ExcCode trap codes to mipsregs.h
MIPS: KVM: Make kvm_mips_{init,exit}() static
MIPS: KVM: Refactor added offsetof()s
MIPS: KVM: Convert EXPORT_SYMBOL to _GPL
...
Linus Torvalds [Sun, 24 Jan 2016 20:45:35 +0000 (12:45 -0800)]
Merge tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Emergency travel prevented me from completing my final testing on this
until today. Nothing here that couldn't wait until RC1 fixes, but I
thought it best to get it out sooner rather than later as it does
contain a build warning fix.
Summary:
A build warning fix, MAINTAINERS cleanup, and a new DMI quirk:
ideapad-laptop:
- Add Lenovo Yoga 700 to no_hw_rfkill dmi list
MAINTAINERS:
- Combine multiple telemetry entries
intel_telemetry_debugfs:
- Fix unused warnings in telemetry debugfs"
* tag 'platform-drivers-x86-v4.5-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
MAINTAINERS: Combine multiple telemetry entries
intel_telemetry_debugfs: Fix unused warnings in telemetry debugfs
Linus Torvalds [Sun, 24 Jan 2016 20:43:06 +0000 (12:43 -0800)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
"The top merge commit was re-generated yesterday because two topic
branches were dropped from this pull request in the last minute due to
some unaddressed comments. All the other material has been in
linux-next for quite a while.
Specifics:
- Enhance thermal core to handle unexpected device cooling states
after fresh boot and system resume. From Zhang Rui and Chen Yu.
- Several fixes and cleanups on Rockchip and RCAR thermal drivers.
From Caesar Wang and Kuninori Morimoto.
- Add Broxton support for Intel processor thermal reporting device
driver. From Amy Wiles"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: trip_point_temp_store() calls thermal_zone_device_update()
thermal: rcar: rcar_thermal_get_temp() return error if strange temp
thermal: rcar: check irq possibility in rcar_thermal_irq_xxx()
thermal: rcar: check every rcar_thermal_update_temp() return value
thermal: rcar: move rcar_thermal_dt_ids to upside
thermal: rockchip: Support the RK3399 SoCs in thermal driver
thermal: rockchip: Support the RK3228 SoCs in thermal driver
dt-bindings: rockchip-thermal: Support the RK3228/RK3399 SoCs compatible
thermal: rockchip: fix a trivial typo
Thermal: Enable Broxton SoC thermal reporting device
thermal: constify pch_dev_ops structure
Thermal: do thermal zone update after a cooling device registered
Thermal: handle thermal zone device properly during system sleep
Thermal: initialize thermal zone device correctly
Linus Torvalds [Sun, 24 Jan 2016 20:39:09 +0000 (12:39 -0800)]
Merge tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs
Pull 9p updates from Eric Van Hensbergen:
"Sorry for the last minute pull request, there's was a change that
didn't get pulled into for-next until two weeks ago and I wanted to
give it some bake time.
Summary:
Rework and error handling fixes, primarily in the fscatch and fd
transports"
* tag 'for-linus-4.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: use fscache mutex rather than spinlock
9p: trans_fd, bail out if recv fcall if missing
9p: trans_fd, read rework to use p9_parse_header
net/9p: Add device name details on error
Linus Torvalds [Sun, 24 Jan 2016 20:34:13 +0000 (12:34 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"The two main changes are aio support in CephFS, and a series that
fixes several issues in the authentication key timeout/renewal code.
On top of that are a variety of cleanups and minor bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: remove outdated comment
libceph: kill off ceph_x_ticket_handler::validity
libceph: invalidate AUTH in addition to a service ticket
libceph: fix authorizer invalidation, take 2
libceph: clear messenger auth_retry flag if we fault
libceph: fix ceph_msg_revoke()
libceph: use list_for_each_entry_safe
ceph: use i_size_{read,write} to get/set i_size
ceph: re-send AIO write request when getting -EOLDSNAP error
ceph: Asynchronous IO support
ceph: Avoid to propagate the invalid page point
ceph: fix double page_unlock() in page_mkwrite()
rbd: delete an unnecessary check before rbd_dev_destroy()
libceph: use list_next_entry instead of list_entry_next
ceph: ceph_frag_contains_value can be boolean
ceph: remove unused functions in ceph_frag.h
Linus Torvalds [Sun, 24 Jan 2016 20:31:12 +0000 (12:31 -0800)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull SMB3 fixes from Steve French:
"A collection of CIFS/SMB3 fixes.
It includes a couple bug fixes, a few for improved debugging of
cifs.ko and some improvements to the way cifs does key generation.
I do have some additional bug fixes I expect in the next week or two
(to address a problem found by xfstest, and some fixes for SMB3.11
dialect, and a couple patches that just came in yesterday that I am
reviewing)"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs_dbg() outputs an uninitialized buffer in cifs_readdir()
cifs: fix race between call_async() and reconnect()
Prepare for encryption support (first part). Add decryption and encryption key generation. Thanks to Metze for helping with this.
cifs: Allow using O_DIRECT with cache=loose
cifs: Make echo interval tunable
cifs: Check uniqueid for SMB2+ and return -ESTALE if necessary
Print IP address of unresponsive server
cifs: Ratelimit kernel log messages
Josh Boyer [Sun, 24 Jan 2016 15:46:42 +0000 (10:46 -0500)]
ideapad-laptop: Add Lenovo Yoga 700 to no_hw_rfkill dmi list
Like the Yoga 900 models the Lenovo Yoga 700 does not have a
hw rfkill switch, and trying to read the hw rfkill switch through the
ideapad module causes it to always reported blocking breaking wifi.
This commit adds the Lenovo Yoga 700 to the no_hw_rfkill dmi list, fixing
the wifi breakage.
If we detect that there is nothing to do just set the flag and do not
check if it was already set before. Races really do not matter. If the
flag is set by any code then the shepherd will start dealing with the
situation and reenable the vmstat workers when necessary again.
Since commit 0eb77e988032 ("vmstat: make vmstat_updater deferrable again
and shut down on idle") quiet_vmstat might update cpu_stat_off and mark
a particular cpu to be handled by vmstat_shepherd. This might trigger a
VM_BUG_ON in vmstat_update because the work item might have been
sleeping during the idle period and see the cpu_stat_off updated after
the wake up. The VM_BUG_ON is therefore misleading and no more
appropriate. Moreover it doesn't really suite any protection from real
bugs because vmstat_shepherd will simply reschedule the vmstat_work
anytime it sees a particular cpu set or vmstat_update would do the same
from the worker context directly. Even when the two would race the
result wouldn't be incorrect as the counters update is fully idempotent.
Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Christoph Lameter <cl@linux.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alban Bedel [Thu, 10 Dec 2015 09:57:20 +0000 (10:57 +0100)]
MIPS: zboot: Avoid useless rebuilds
Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.
When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.
Signed-off-by: Alban Bedel <albeu@free.fr> Cc: linux-mips@linux-mips.org Cc: Alex Smith <alex.smith@imgtec.com> Cc: Wu Zhangjin <wuzhangjin@gmail.com> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simon Arlott [Sun, 13 Dec 2015 22:47:55 +0000 (22:47 +0000)]
MIPS: bcm963xx: Move extended flash address to bcm_tag header file
The extended flash address needs to be subtracted from bcm_tag flash
image offsets. Move this value to the bcm_tag header file.
Renamed define name to consistently use bcm963xx for flash layout
which should be considered a property of the board and not the SoC
(i.e. bcm63xx could theoretically be used on a board without CFE
or any flash).
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org> Cc: MIPS Mailing List <linux-mips@linux-mips.org> Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11833/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simon Arlott [Sun, 13 Dec 2015 22:45:30 +0000 (22:45 +0000)]
MIPS: bcm963xx: Add Broadcom BCM963xx board nvram data structure
Broadcom BCM963xx boards have multiple nvram variants across different
SoCs with additional checksum fields added whenever the size of the
nvram was extended.
Add this structure as a header file so that multiple drivers can use it.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Kevin Cernekee <cernekee@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Jonas Gorski <jogo@openwrt.org> Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org> Cc: MIPS Mailing List <linux-mips@linux-mips.org> Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11830/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Sun, 24 Jan 2016 02:45:06 +0000 (18:45 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.5 merge window patches
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- Add support for remote invalidate to the iSER driver (pushed
through the RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to
dependencies, acknowledged by Bruce)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (169 commits)
IB/mlx5: Unify CQ create flags check
IB/mlx5: Expose Raw Packet QP to user space consumers
{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib
IB/mlx5: Support setting Ethernet priority for Raw Packet QPs
IB/mlx5: Add Raw Packet QP query functionality
IB/mlx5: Add create and destroy functionality for Raw Packet QP
IB/mlx5: Refactor mlx5_ib_qp to accommodate other QP types
IB/mlx5: Allocate a Transport Domain for each ucontext
net/mlx5_core: Warn on unsupported events of QP/RQ/SQ
net/mlx5_core: Add RQ and SQ event handling
net/mlx5_core: Export transport objects
IB/mlx5: Expose CQE version to user-space
IB/mlx5: Add CQE version 1 support to user QPs and SRQs
IB/mlx5: Fix data validation in mlx5_ib_alloc_ucontext
IB/sa: Fix netlink local service GFP crash
IB/srpt: Remove redundant wc array
IB/qib: Improve ipoib UD performance
IB/mlx4: Advertise RoCE v2 support
IB/mlx4: Create and use another QP1 for RoCEv2
IB/mlx4: Enable send of RoCE QP1 packets with IP/UDP headers
...
James Hogan [Wed, 16 Dec 2015 23:49:38 +0000 (23:49 +0000)]
MIPS: Move KVM specific opcodes into asm/inst.h
The header arch/mips/kvm/opcode.h defines a few extra opcodes which
aren't in arch/mips/include/uapi/asm/inst.h. There's nothing KVM
specific about them, so lets move them into inst.h where they belong and
delete the header.
Note that mfmcz_op is renamed to mfmc0_op to match the instruction set
manual, and wait_op was already added to inst.h in commit b0a3eae2b943
("MIPS: inst.h: define COP0 wait op"), merged in v3.16-rc1.
projects / karo-tx-linux.git / log