PTRACE_SETVFPREGS fails to properly mark the VFP register set to be
reloaded, because it undoes one of the effects of vfp_flush_hwstate().
Specifically vfp_flush_hwstate() sets thread->vfpstate.hard.cpu to
an invalid CPU number, but vfp_set() overwrites this with the original
CPU number, thereby rendering the hardware state as apparently "valid",
even though the software state is more recent.
Fix this by reverting the previous change.
Fixes: 8130b9d7b9d8 ("ARM: 7308/1: vfp: flush thread hwstate before copying ptrace registers") Acked-by: Will Deacon <will.deacon@arm.com> Tested-by: Simon Marchi <simon.marchi@ericsson.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That is some different register for ALC255 and ALC256.
ALC256 can't fit with some ALC255 register.
This issue is cause from LDO output voltage control.
This patch is updated the right LDO register value.
MOV to DR6 or DR7 causes a #GP if an attempt is made to write a 1 to
any of bits 63:32. However, this is not detected at KVM_SET_DEBUGREGS
time, and the next KVM_RUN oopses:
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: David Wragg <david@weave.works> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow the MTU of geneve devices to be set to large values, in order to
exploit underlying networks with larger frame sizes.
GENEVE does not have a fixed encapsulation overhead (an openvswitch
rule can add variable length options), so there is no relevant maximum
MTU to enforce. A maximum of IP_MAX_MTU is used instead.
Encapsulated packets that are too big for the underlying network will
get dropped on the floor.
Signed-off-by: David Wragg <david@weave.works> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow the MTU of vxlan devices without an underlying device to be set
to larger values (up to a maximum based on IP packet limits and vxlan
overhead).
Previously, their MTUs could not be set to higher than the
conventional ethernet value of 1500. This is a very arbitrary value
in the context of vxlan, and prevented vxlan devices from being able
to take advantage of jumbo frames etc.
The default MTU remains 1500, for compatibility.
Signed-off-by: David Wragg <david@weave.works> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present we perform an xfrm_lookup() for each UDPv6 message we
send. The lookup involves querying the flow cache (flow_cache_lookup)
and, in case of a cache miss, creating an XFRM bundle.
If we miss the flow cache, we can end up creating a new bundle and
deriving the path MTU (xfrm_init_pmtu) from on an already transformed
dst_entry, which we pass from the socket cache (sk->sk_dst_cache) down
to xfrm_lookup(). This can happen only if we're caching the dst_entry
in the socket, that is when we're using a connected UDP socket.
To put it another way, the path MTU shrinks each time we miss the flow
cache, which later on leads to incorrectly fragmented payload. It can
be observed with ESPv6 in transport mode:
1) Set up a transformation and lower the MTU to trigger fragmentation
# ip xfrm policy add dir out src ::1 dst ::1 \
tmpl src ::1 dst ::1 proto esp spi 1
# ip xfrm state add src ::1 dst ::1 \
proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
# ip link set dev lo mtu 1500
2) Monitor the packet flow and set up an UDP sink
# tcpdump -ni lo -ttt &
# socat udp6-listen:12345,fork /dev/null &
4) Compare it to a non-connected socket
# perl -e 'print "@" x 1500' | socat - udp6-sendto:[::1]:12345
00:00:40.535488 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x6), length 1448
00:00:00.000010 IP6 ::1 > ::1: frag (1448|64)
What happens in step (3) is:
1) when connecting the socket in __ip6_datagram_connect(), we
perform an XFRM lookup, miss the flow cache, create an XFRM
bundle, and cache the destination,
2) afterwards, when sending the datagram, we perform an XFRM lookup,
again, miss the flow cache (due to mismatch of flowi6_iif and
flowi6_oif, which is an issue of its own), and recreate an XFRM
bundle based on the cached (and already transformed) destination.
To prevent the recreation of an XFRM bundle, avoid an XFRM lookup
altogether whenever we already have a destination entry cached in the
socket. This prevents the path MTU shrinkage and brings us on par with
UDPv4.
The fix also benefits connected PINGv6 sockets, another user of
ip6_sk_dst_lookup_flow(), who also suffer messages being transformed
twice.
Joint work with Hannes Frederic Sowa.
Reported-by: Jan Tluka <jtluka@redhat.com> Signed-off-by: Jakub Sitnicki <jkbs@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unused fields of udp_cfg must be all zeros. Otherwise
setup_udp_tunnel_sock() fills ->gro_receive and ->gro_complete
callbacks with garbage, eventually resulting in panic when used by
udp_gro_receive().
v2: use empty initialiser instead of "{ NULL }" to avoid relying on
first field's type.
Fixes: 38fd2af24fcf ("udp: Add socket based GRO and config") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The missing br_vlan_should_use() test caused creation of an unneeded
local fdb entry on changing mac address of a bridge device when there is
a vlan which is configured on a bridge port but not on the bridge
device.
Fixes: 2594e9064a57 ("bridge: vlan: add per-vlan struct and move to rhashtables") Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When create a new vxlan link, example:
ip link add vtap mtu 1440 type vxlan vni 1 dev eth0
The argument "mtu" has no effect, because it is not set to conf->mtu. The
default value is used in vxlan_dev_configure function.
This problem was introduced by commit 0dfbdf4102b9 (vxlan: Factor out device
configuration).
Fixes: 0dfbdf4102b9 (vxlan: Factor out device configuration) Signed-off-by: Chen Haiquan <oc@yunify.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The team_device_event() notifier calls team_compute_features() to fix
vlan_features under team->lock to protect team->port_list. The problem is
that subsequent __team_compute_features() calls netdev_change_features()
to propagate vlan_features to upper vlan devices while team->lock is still
taken. This can lead to deadlock when NETIF_F_LRO is modified on lower
devices or team device itself.
Example:
The team0 as active backup with eth0 and eth1 NICs. Both eth0 & eth1 are
LRO capable and LRO is enabled. Thus LRO is also enabled on team0.
The command 'ethtool -K team0 lro off' now hangs due to this deadlock:
The bug is present in team from the beginning but it appeared after the commit fd867d5 (net/core: generic support for disabling netdev features down stack)
that adds synchronization of features with lower devices.
Fixes: fd867d5 (net/core: generic support for disabling netdev features down stack) Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise, if we fail to allocate new PIO buffers, our TXQs will try to
use the old ones, which aren't there any more.
Fixes: 183233bec810 "sfc: Allocate and link PIO buffers; map them with write-combining" Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow-up to commit e27f4a942a0e ("bpf: Use mount_nodev not mount_ns
to mount the bpf filesystem"), which removes the FS_USERNS_MOUNT flag.
The original idea was to have a per mountns instance instead of a
single global fs instance, but that didn't work out and we had to
switch to mount_nodev() model. The intent of that middle ground was
that we avoid users who don't play nice to create endless instances
of bpf fs which are difficult to control and discover from an admin
point of view, but at the same time it would have allowed us to be
more flexible with regard to namespaces.
Therefore, since we now did the switch to mount_nodev() as a fix
where individual instances are created, we also need to remove userns
mount flag along with it to avoid running into mentioned situation.
I don't expect any breakage at this early point in time with removing
the flag and we can revisit this later should the requirement for
this come up with future users. This and commit e27f4a942a0e have
been split to facilitate tracking should any of them run into the
unlikely case of causing a regression.
Fixes: b2197755b263 ("bpf: add support for persistent maps/progs") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These structures are defined only if __USE_MISC is set in glibc net/if.h
headers, ie when _BSD_SOURCE or _SVID_SOURCE are defined.
CC: Jan Engelhardt <jengelh@inai.de> CC: Josh Boyer <jwboyer@fedoraproject.org> CC: Stephen Hemminger <shemming@brocade.com> CC: Waldemar Brodkorb <mail@waldemar-brodkorb.de> CC: Gabriel Laskar <gabriel@lse.epita.fr> CC: Mikko Rapeli <mikko.rapeli@iki.fi> Fixes: 4a91cb61bb99 ("uapi glibc compat: fix compile errors when glibc net/if.h included before linux/if.h") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While reviewing the filesystems that set FS_USERNS_MOUNT I spotted the
bpf filesystem. Looking at the code I saw a broken usage of mount_ns
with current->nsproxy->mnt_ns. As the code does not acquire a
reference to the mount namespace it can not possibly be correct to
store the mount namespace on the superblock as it does.
Replace mount_ns with mount_nodev so that each mount of the bpf
filesystem returns a distinct instance, and the code is not buggy.
In discussion with Hannes Frederic Sowa it was reported that the use
of mount_ns was an attempt to have one bpf instance per mount
namespace, in an attempt to keep resources that pin resources from
hiding. That intent simply does not work, the vfs is not built to
allow that kind of behavior. Which means that the bpf filesystem
really is buggy both semantically and in it's implemenation as it does
not nor can it implement the original intent.
This change is userspace visible, but my experience with similar
filesystems leads me to believe nothing will break with a model of each
mount of the bpf filesystem is distinct from all others.
Fixes: b2197755b263 ("bpf: add support for persistent maps/progs") Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We used to check dev->reg_state against NETREG_REGISTERED after each
time we are woke up. But after commit 9e641bdcfa4e ("net-tun:
restructure tun_do_read for better sleep/wakeup efficiency"), it uses
skb_recv_datagram() which does not check dev->reg_state. This will
result if we delete a tun/tap device after a process is blocked in the
reading. The device will wait for the reference count which was held
by that process for ever.
Fixes this by using RCV_SHUTDOWN which will be checked during
sk_recv_datagram() before trying to wake up the process during uninit.
Fixes: 9e641bdcfa4e ("net-tun: restructure tun_do_read for better
sleep/wakeup efficiency") Cc: Eric Dumazet <edumazet@google.com> Cc: Xi Wang <xii@google.com> Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is that fib_info->nh is [0] so the struct fib_info
allocation size depends on number of nexthops. If we just copy fib_info,
we do not copy the nexthops info and driver accesses memory which is not
ours.
Given the fact that fib4 does not defer operations and therefore it does
not need copy, just pass the pointer down to drivers as it was done
before.
Fixes: 850d0cbc91 ("switchdev: remove pointers from switchdev objects") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The publication field of the old netlink API should contain the
publication key and not the publication reference.
Fixes: 44a8ae94fd55 (tipc: convert legacy nl name table dump to nl compat) Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we free cb->skb after a dump, we do it after releasing the
lock. This means that a new dump could have started in the time
being and we'll end up freeing their skb instead of ours.
This patch saves the skb and module before we unlock so we free
the right memory.
Fixes: 16b304f3404f ("netlink: Eliminate kmalloc in netlink dump operation.") Reported-by: Baozeng Ding <sploving1@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the socket for which the user is listing publication exists
before parsing the socket netlink attributes.
Prior to this patch a call without any socket caused a NULL pointer
dereference in tipc_nl_publ_dump().
Tested-and-reported-by: Baozeng Ding <sploving1@gmail.com> Signed-off-by: Richard Alpe <richard.alpe@ericsson.com> Acked-by: Jon Maloy <jon.maloy@ericsson.cm> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this by suppressing VPD inquiry for this device.
Signed-off-by: Ewan D. Milne <emilne@redhat.com> Reported-by: Jan Stancek <jstancek@redhat.com> Tested-by: Jan Stancek <jstancek@redhat.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When SCSI was written, all commands coming from the filesystem
(REQ_TYPE_FS commands) had data. This meant that our signal for needing
to complete the command was the number of bytes completed being equal to
the number of bytes in the request. Unfortunately, with the advent of
flush barriers, we can now get zero length REQ_TYPE_FS commands, which
confuse this logic because they satisfy the condition every time. This
means they never get retried even for retryable conditions, like UNIT
ATTENTION because we complete them early assuming they're done. Fix
this by special casing the early completion condition to recognise zero
length commands with errors and let them drop through to the retry code.
Reported-by: Sebastian Parschauer <s.parschauer@gmx.de> Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com> Tested-by: Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we do dquot readahead in log recovery, we do not use a verifier
as the underlying buffer may not have dquots in it. e.g. the
allocation operation hasn't yet been replayed. Hence we do not want
to fail recovery because we detect an operation to be replayed has
not been run yet. This problem was addressed for inodes in commit d891400 ("xfs: inode buffers may not be valid during recovery
readahead") but the problem was not recognised to exist for dquots
and their buffers as the dquot readahead did not have a verifier.
The result of not using a verifier is that when the buffer is then
next read to replay a dquot modification, the dquot buffer verifier
will only be attached to the buffer if *readahead is not complete*.
Hence we can read the buffer, replay the dquot changes and then add
it to the delwri submission list without it having a verifier
attached to it. This then generates warnings in xfs_buf_ioapply(),
which catches and warns about this case.
Fix this and make it handle the same readahead verifier error cases
as for inode buffers by adding a new readahead verifier that has a
write operation as well as a read operation that marks the buffer as
not done if any corruption is detected. Also make sure we don't run
readahead if the dquot buffer has been marked as cancelled by
recovery.
This will result in readahead either succeeding and the buffer
having a valid write verifier, or readahead failing and the buffer
state requiring the subsequent read to resubmit the IO with the new
verifier. In either case, this will result in the buffer always
ending up with a valid write verifier on it.
Note: we also need to fix the inode buffer readahead error handling
to mark the buffer with EIO. Brian noticed the code I copied from
there wrong during review, so fix it at the same time. Add comments
linking the two functions that handle readahead verifier errors
together so we don't forget this behavioural link in future.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a name to each buf_ops structure, so that if
a verifier fails we can print the type of verifier that
failed it. Should be a slight debugging aid, I hope.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Cc: Holger Hoffstätte <holger@applied-asynchrony.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't write back stale inodes so we should skip them in
xfs_iflush_cluster, too.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some careless idiot(*) wrote crap code in commit 1a3e8f3 ("xfs:
convert inode cache lookups to use RCU locking") back in late 2010,
and so xfs_iflush_cluster checks the wrong inode for whether it is
still valid under RCU protection. Fix it to lock and check the
correct inode.
(*) Careless-idiot: Dave Chinner <dchinner@redhat.com>
Discovered-by: Brain Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a failure due to an inode buffer occurs, the error handling
fails to abort the inode writeback correctly. This can result in the
inode being reclaimed whilst still in the AIL, leading to
use-after-free situations as well as filesystems that cannot be
unmounted as the inode log items left in the AIL never get removed.
Fix this by ensuring fatal errors from xfs_imap_to_bp() result in
the inode flush being aborted correctly.
Reported-by: Shyam Kaushik <shyam@zadarastorage.com> Diagnosed-by: Shyam Kaushik <shyam@zadarastorage.com> Tested-by: Shyam Kaushik <shyam@zadarastorage.com> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 96f859d ("libxfs: pack the agfl header structure so
XFS_AGFL_SIZE is correct") allowed the freelist to use the empty
slot at the end of the freelist on 64 bit systems that was not
being used due to sizeof() rounding up the structure size.
This has caused versions of xfs_repair prior to 4.5.0 (which also
has the fix) to report this as a corruption once the filesystem has
been grown. Older kernels can also have problems (seen from a whacky
container/vm management environment) mounting filesystems grown on a
system with a newer kernel than the vm/container it is deployed on.
To avoid this problem, change the initial free list indexes not to
wrap across the end of the AGFL, hence avoiding the initialisation
of agf_fllast to the last index in the AGFL.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Today, a kernel which refuses to mount a filesystem read-write
due to unknown ro-compat features can still transition to read-write
via the remount path. The old kernel is most likely none the wiser,
because it's unaware of the new feature, and isn't using it. However,
writing to the filesystem may well corrupt metadata related to that
new feature, and moving to a newer kernel which understand the feature
will have problems.
Right now the only ro-compat feature we have is the free inode btree,
which showed up in v3.16. It would be good to push this back to
all the active stable kernels, I think, so that if anyone is using
newer mkfs (which enables the finobt feature) with older kernel
releases, they'll be protected.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Bill O'Donnell <billodo@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling CONFIG_GCOV_PROFILE_ALL produces us a lot of warnings like
lib/lz4/lz4hc_compress.c: In function 'lz4_compresshcctx':
lib/lz4/lz4hc_compress.c:514:1: warning: the frame size of 1504 bytes is larger than 1024 bytes [-Wframe-larger-than=]
After some investigation, I found that this behavior started with gcc-4.9,
and opened https://gcc.gnu.org/bugzilla/show_bug.cgi?id=69702.
A suggested workaround for it is to use the -fno-tree-loop-im
flag that turns off one of the optimization stages in gcc, so the
code runs a little slower but does not use excessive amounts
of stack.
We could make this conditional on the gcc version, but I could not
find an easy way to do this in Kbuild and the benefit would be
fairly small, given that most of the gcc version in production are
affected now.
I'm marking this for 'stable' backports because it addresses a bug
with code generation in gcc that exists in all kernel versions
with the affected gcc releases.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 21a59991ce0c ("scripts/package/Makefile: rpmbuild is needed
for rpm targets"), it is no longer possible to specify RPMOPTS.
For example, we can no longer able to control _topdir using the following
make command.
make RPMOPTS="--define '_topdir /home/xyz/workspace/'" binrpm-pkg
Fixes: 21a59991ce0c ("scripts/package/Makefile: rpmbuild is needed for rpm targets") Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With netconsole (at least) the pr_err("... disablingn") call can
recurse back into the dma-debug code, where it'll try to grab
free_entries_lock again. Avoid the problem by doing the printk after
dropping the lock.
The PM runtime will be left disabled for the device if its
.suspend_late() callback fails and async suspend is not allowed
for this device. In this case device will not be added in
dpm_late_early_list and dpm_resume_early() will ignore this
device, as result PM runtime will be disabled for it forever
(side effect: after 8 subsequent failures for the same device
the PM runtime will be reenabled due to disable_depth overflow).
To fix this problem, add devices to dpm_late_early_list regardless
of whether or not device_suspend_late() returns errors for them.
That will ensure failures in there to be handled consistently for
all devices regardless of their async suspend/resume status.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com> Tested-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, in ext4_mb_init(), there's a loop like the following:
do {
...
offset += 1 << (sb->s_blocksize_bits - i);
i++;
} while (i <= sb->s_blocksize_bits + 1);
Note that the updated offset is used in the loop's next iteration only.
However, at the last iteration, that is at i == sb->s_blocksize_bits + 1,
the shift count becomes equal to (unsigned)-1 > 31 (c.f. C99 6.5.7(3))
and UBSAN reports
Observe that the mentioned shift exponent, 4294967295, equals (unsigned)-1.
Unless compilers start to do some fancy transformations (which at least
GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the
such calculated value of offset is never used again.
Silence UBSAN by introducing another variable, offset_incr, holding the
next increment to apply to offset and adjust that one by right shifting it
by one position per loop iteration.
Unless compilers start to do some fancy transformations (which at least
GCC 6.0.0 doesn't currently do), the issue is of cosmetic nature only: the
such calculated value of bb is never used again.
Silence UBSAN by introducing another variable, bb_incr, holding the next
increment to apply to bb and adjust that one by right shifting it by one
position per loop iteration.
When filesystem is corrupted in the right way, it can happen
ext4_mark_iloc_dirty() in ext4_orphan_add() returns error and we
subsequently remove inode from the in-memory orphan list. However this
deletion is done with list_del(&EXT4_I(inode)->i_orphan) and thus we
leave i_orphan list_head with a stale content. Later we can look at this
content causing list corruption, oops, or other issues. The reported
trace looked like:
Instead of just printing warning messages, if the orphan list is
corrupted, declare the file system is corrupted. If there are any
reserved inodes in the orphaned inode list, declare the file system
corrupted and stop right away to avoid doing more potential damage to
the file system.
If the orphaned inode list contains inode #5, ext4_iget() returns a
bad inode (since the bootloader inode should never be referenced
directly). Because of the bad inode, we end up processing the inode
repeatedly and this hangs the machine.
(But don't do this if you are using an unpatched kernel if you care
about the system staying functional. :-)
This bug was found by the port of American Fuzzy Lop into the kernel
to find file system problems[1]. (Since it *only* happens if inode #5
shows up on the orphan list --- 3, 7, 8, etc. won't do it, it's not
surprising that AFL needed two hours before it found it.)
The component master driver imx-drm-core matches component devices using
their of_node. Since commit 950b410dd1ab ("gpu: ipu-v3: Fix imx-ipuv3-crtc
module autoloading"), the imx-ipuv3-crtc dev->of_node is not set during
probing. Before that, of_node was set and caused an of: modalias to be
used instead of the platform: modalias, which broke module autoloading.
On the other hand, if dev->of_node is not set yet when the imx-ipuv3-crtc
probe function calls component_add, component matching in imx-drm-core
fails. While dev->of_node will be set once the next component tries to
bring up the component master, imx-drm-core component binding will never
succeed if one of the crtc devices is probed last.
Add of_node to the component platform data and match against the
pdata->of_node instead of dev->of_node in imx-drm-core to work around
this problem.
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com> Fixes: 243e6a44b9ca ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Matt Roper <matthew.d.roper@intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 15606534bf0a65d8a74a90fd57b8712d147dbca6) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lyude [Tue, 31 May 2016 16:49:07 +0000 (12:49 -0400)]
drm/atomic: Verify connector->funcs != NULL when clearing states
Unfortunately since we don't have Dave's connector refcounting patch
here yet, it's very possible that drm_atomic_state_default_clear() could
get called by intel_display_resume() when
intel_dp_mst_destroy_connector() isn't completely finished destroying an
mst connector, but has already finished setting connector->funcs to
NULL. As such, we need to treat the connector like it's already been
destroyed and just skip it, otherwise we'll end up dereferencing a NULL
pointer.
This fix is only required for 4.6 and below. David Airlie's patchseries
for 4.7 to add connector reference counting provides a more proper fix
for this.
Changes since v1:
- Fix leftover whitespace
Upstream fix: 0552f7651bc2 ("drm/i915/mst: use reference counted
connectors. (v3)") Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Lyude <cpaul@redhat.com>
During boot, MST hotplugs are generally expected (even if no physical
hotplugging occurs) and result in DRM's connector topology changing.
This means that using num_connector from the current mode configuration
can lead to the number of connectors changing under us. This can lead to
some nasty scenarios in fbcon:
- We allocate an array to the size of dev->mode_config.num_connectors.
- MST hotplug occurs, dev->mode_config.num_connectors gets incremented.
- We try to loop through each element in the array using the new value
of dev->mode_config.num_connectors, and end up going out of bounds
since dev->mode_config.num_connectors is now larger then the array we
allocated.
fb_helper->connector_count however, will always remain consistent while
we do a modeset in fb_helper.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
During boot time, MST devices usually send a ton of hotplug events
irregardless of whether or not any physical hotplugs actually occurred.
Hotplugs mean connectors being created/destroyed, and the number of DRM
connectors changing under us. This isn't a problem if we use
fb_helper->connector_count since we only set it once in the code,
however if we use num_connector from struct drm_mode_config we risk it's
value changing under us. On top of that, there's even a chance that
dev->mode_config.num_connector != fb_helper->connector_count. If the
number of connectors happens to increase under us, we'll end up using
the wrong array size for memcpy and start writing beyond the actual
length of the array, occasionally resulting in kernel panics.
Note: This is just polish for 4.7, Dave Airlie's drm_connector
refcounting fixed these bugs for real. But it's good enough duct-tape
for stable kernel backporting, since backporting the refcounting
changes is way too invasive.
When porting the hdmi deep color detection code from
radeon-kms to amdgpu-kms apparently some kind of
copy and paste error happened, attaching an else
branch to the wrong if statement.
The result is that hdmi deep color mode is always
disabled, regardless of gpu and display capabilities and
user wishes, as the code mistakenly thinks that the display
doesn't provide the required max_tmds_clock limit and falls
back to 8 bpc.
This patch fixes deep color support, as tested on a
R9 380 Tonga Pro + suitable display, and should be
backported to all kernels with amdgpu-kms support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix possible out of bounds read, by adding missing comma.
The code may read pass the end of the dsi_errors array
when the most significant bit (bit #31) in the intr_stat register
is set.
This bug has been detected using CppCheck (static analysis tool).
The length of the GSS MIC token need not be a multiple of four bytes.
It is then padded by XDR to a multiple of 4 B, but unwrap_integ_data()
would previously only trim mic.len + 4 B. The remaining up to three
bytes would then trigger a check in nfs4svc_decode_compoundargs(),
leading to a "garbage args" error and mount failure:
nfs4svc_decode_compoundargs: compound not properly padded!
nfsd: failed to decode arguments!
This would prevent older clients using the pre-RFC 4121 MIC format
(37-byte MIC including a 9-byte OID) from mounting exports from v3.9+
servers using krb5i.
The trimming was introduced by commit 4c190e2f913f ("sunrpc: trim off
trailing checksum before returning decrypted or integrity authenticated
buffer").
Fixes: 4c190e2f913f "unrpc: trim off trailing checksum..." Signed-off-by: Tomáš Trnka <ttrnka@mail.muni.cz> Acked-by: Jeff Layton <jlayton@poochiereds.net> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of having two functions for cycling through the E820 map in
order to count to be remapped pages and remap them later, just use one
function with a caller supplied sub-function called for each region to
be processed. This eliminates the possibility of a mismatch between
both loops which showed up in certain configurations.
Suggested-by: Ed Swierk <eswierk@skyportsystems.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ff1e22e7a638 ("xen/events: Mask a moving irq") open-coded
irq_move_irq() but left out checking if the IRQ is disabled. This broke
resuming from suspend since it tries to move a (disabled) irq without
holding the IRQ's desc->lock. Fix it by adding in a check for disabled
IRQs.
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrou device are transferred to guest and
backwards. The content in the device's config space will be lost
on PE reset issued in the middle of the recovery. The function
saves/restores it before/after the reset. However, config access
to some adapters like Broadcom BCM5719 at this point will causes
fenced PHB. The config space is always blocked and we save 0xFF's
that are restored at late point. The memory BARs are totally
corrupted, causing another EEH error upon access to one of the
memory BARs.
This restores the config space on those adapters like BCM5719
from the content saved to the EEH device when it's populated,
to resolve above issue.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices") Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Russell Currey <ruscur@russell.cc> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function eeh_add_device_early() is used to perform EEH
initialization in devices added later on the system, like in
hotplug/DLPAR scenarios. Since the commit 89a51df5ab1d ("powerpc/eeh:
Fix crash in eeh_add_device_early() on Cell") a new check was introduced
in this function - Cell has no EEH capabilities which led to kernel oops
if hotplug was performed, so checking for eeh_enabled() was introduced
to avoid the issue.
However, in architectures that EEH is present like pSeries or PowerNV,
we might reach a case in which no PCI devices are present on boot time
and so EEH is not initialized. Then, if a device is added via DLPAR for
example, eeh_add_device_early() fails because eeh_enabled() is false,
and EEH end up not being enabled at all.
This reverts the aforementioned patch since a new verification was
introduced by the commit d91dafc02f42 ("powerpc/eeh: Delay probing EEH
device during hotplug") and so the original Cell issue does not happen
anymore.
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function eeh_pe_reset_and_recover() is used to recover EEH
error when the passthrough device are transferred to guest and
backwards, meaning the device's driver is vfio-pci or none.
When the driver is vfio-pci that provides error_detected() error
handler only, the handler simply stops the guest and it's not
expected behaviour. On the other hand, no error handlers will
be called if we don't have a bound driver.
This ignores the error handler in eeh_pe_reset_and_recover()
that reports the error to device driver to avoid the exceptional
behaviour.
Fixes: 5cfb20b9 ("powerpc/eeh: Emulate EEH recovery for VFIO devices") Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com> Reviewed-by: Russell Currey <ruscur@russell.cc> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the interrupt vectors on 64-bit POWER server processors are only
32 bytes long (8 instructions), which is not enough for the full
first-level interrupt handler. For these we need to branch to an
out-of-line (OOL) handler. But when we are running a relocatable kernel,
interrupt vectors till __end_interrupts marker are copied down to real
address 0x100. So, branching to labels (ie. OOL handlers) outside this
section must be handled differently (see LOAD_HANDLER()), considering
relocatable kernel, which would need at least 4 instructions.
However, branching from interrupt vector means that we corrupt the
CFAR (come-from address register) on POWER7 and later processors as
mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions)
that contains the part up to the point where the CFAR is saved in the
PACA should be part of the short interrupt vectors before we branch out
to OOL handlers.
But as mentioned already, there are interrupt vectors on 64-bit POWER
server processors that are only 32 bytes long (like vectors 0x4f00,
0x4f20, etc.), which cannot accomodate the above two cases at the same
time owing to space constraint. Currently, in these interrupt vectors,
we simply branch out to OOL handlers, without using LOAD_HANDLER(),
which leaves us vulnerable when running a relocatable kernel (eg. kdump
case). While this has been the case for sometime now and kdump is used
widely, we were fortunate not to see any problems so far, for three
reasons:
1. In almost all cases, production kernel (relocatable) is used for
kdump as well, which would mean that crashed kernel's OOL handler
would be at the same place where we end up branching to, from short
interrupt vector of kdump kernel.
2. Also, OOL handler was unlikely the reason for crash in almost all
the kdump scenarios, which meant we had a sane OOL handler from
crashed kernel that we branched to.
3. On most 64-bit POWER server processors, page size is large enough
that marking interrupt vector code as executable (see commit 429d2e83) leads to marking OOL handler code from crashed kernel,
that sits right below interrupt vector code from kdump kernel, as
executable as well.
Let us fix this by moving the __end_interrupts marker down past OOL
handlers to make sure that we also copy OOL handlers to real address
0x100 when running a relocatable kernel.
This fix has been tested successfully in kdump scenario, on an LPAR with
4K page size by using different default/production kernel and kdump
kernel.
Also tested by manually corrupting the OOL handlers in the first kernel
and then kdump'ing, and then causing the OOL handlers to fire - mpe.
Fixes: c1fb6816fb1b ("powerpc: Add relocation on exception vector handlers") Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com> Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On no-so-small systems, it is possible for a single process to cause an
OOM condition by filling large pipes with data that are never read. A
typical process filling 4000 pipes with 1 MB of data will use 4 GB of
memory. On small systems it may be tricky to set the pipe max size to
prevent this from happening.
This patch makes it possible to enforce a per-user soft limit above
which new pipes will be limited to a single page, effectively limiting
them to 4 kB each, as well as a hard limit above which no new pipes may
be created for this user. This has the effect of protecting the system
against memory abuse without hurting other users, and still allowing
pipes to work correctly though with less data at once.
The limit are controlled by two new sysctls : pipe-user-pages-soft, and
pipe-user-pages-hard. Both may be disabled by setting them to zero. The
default soft limit allows the default number of FDs per process (1024)
to create pipes of the default size (64kB), thus reaching a limit of 64MB
before starting to create only smaller pipes. With 256 processes limited
to 1024 FDs each, this results in 1024*64kB + (256*1024 - 1024) * 4kB =
1084 MB of memory allocated for a user. The hard limit is disabled by
default to avoid breaking existing applications that make intensive use
of pipes (eg: for splicing).
creates an unreapable zombie if /sbin/init doesn't use __WALL.
This is not a kernel bug, at least in a sense that everything works as
expected: debugger should reap a traced sub-thread before it can reap the
leader, but without __WALL/__WCLONE do_wait() ignores sub-threads.
Unfortunately, it seems that /sbin/init in most (all?) distributions
doesn't use it and we have to change the kernel to avoid the problem.
Note also that most init's use sys_waitid() which doesn't allow __WALL, so
the necessary user-space fix is not that trivial.
This patch just adds the "ptrace" check into eligible_child(). To some
degree this matches the "tsk->ptrace" in exit_notify(), ->exit_signal is
mostly ignored when the tracee reports to debugger. Or WSTOPPED, the
tracer doesn't need to set this flag to wait for the stopped tracee.
This obviously means the user-visible change: __WCLONE and __WALL no
longer have any meaning for debugger. And I can only hope that this won't
break something, but at least strace/gdb won't suffer.
We could make a more conservative change. Say, we can take __WCLONE into
account, or !thread_group_leader(). But it would be nice to not
complicate these historical/confusing checks.
Since commit 92923ca3aace ("mm: meminit: only set page reserved in the
memblock region") the reserved bit is set on reserved memblock regions.
However start and end address are passed as unsigned long. This is only
32bit on i386, so it can end up marking the wrong pages reserved for
ranges at 4GB and above.
This was observed on a 32bit Xen dom0 which was booted with initial
memory set to a value below 4G but allowing to balloon in memory
(dom0_mem=1024M for example). This would define a reserved bootmem
region for the additional memory (for example on a 8GB system there was
a reverved region covering the 4GB-8GB range). But since the addresses
were passed on as unsigned long, this was actually marking all pages
from 0 to 4GB as reserved.
Fixes: 92923ca3aacef63 ("mm: meminit: only set page reserved in the memblock region") Link: http://lkml.kernel.org/r/1463491221-10573-1-git-send-email-stefan.bader@canonical.com Signed-off-by: Stefan Bader <stefan.bader@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In v4l2-compliance utility, test VIDIOC_CREATE_BUFS will check whether reserved
filed of v4l2_create_buffers filled with zero
Reserved field is filled with zero in v4l_create_bufs.
This patch copy reserved field of v4l2_create_buffer from kernel space to user
space
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
b84106b4e229 ("PCI: Disable IO/MEM decoding for devices with non-compliant
BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with
the PCI spec. But it didn't do anything for expansion ROM BARs, so we
still try to size them, resulting in warnings like this on Broadwell-EP:
pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref]
Move the non-compliant BAR check from __pci_read_base() up to
pci_read_bases() so it applies to the expansion ROM BAR as well as
to BARs 0-5.
Note that direct callers of __pci_read_base(), like sriov_init(), will now
bypass this check. We haven't had reports of devices with broken SR-IOV
BARs yet.
The range is registered into a linked list which can be referenced
throughout the lifetime of the driver. Ensure the range's memory is useful
for the same lifetime by adding it to the driver's private data structure.
The bug was introduced in the driver's initial commit, which was present in
v3.10.
Fixes: f0b9a7e521fa ("pinctrl: exynos5440: add pinctrl driver for Samsung EXYNOS5440 SoC") Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Tomasz Figa <tomasz.figa@gmail.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bcm2835_pll_off is currently assigning CM_PLL_ANARST to the control
register, which may lose the other bits that are currently set by the
clock dividers.
It also now locks during the read/modify/write cycle of both
registers.
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Eric Anholt <eric@anholt.net> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clk_register() function returns a valid pointer to struct clk or
ERR_PTR() error code, this makes a check for returned NULL value
useless and may lead to oops on error path.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: bcc5fd49a0fd ("clk: at91: add a driver for the h32mx clock") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In poweroff, we set the reset bit and the power down bit, but only
managed to unset the reset bit for poweron. This meant that if HDMI
did -EPROBE_DEFER after it had grabbed its clocks, we'd power down the
PLLH (that had been on at boot time) and never recover.
Signed-off-by: Eric Anholt <eric@anholt.net> Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0b89e9aa2856 (cpuidle: delay enabling interrupts until all
coupled CPUs leave idle) rightfully fixed a regression by letting
the coupled idle state framework to handle local interrupt enabling
when the CPU is exiting an idle state.
The current code checks if the idle state is coupled and, if so, it
will let the coupled code to enable interrupts. This way, it can
decrement the ready-count before handling the interrupt. This
mechanism prevents the other CPUs from waiting for a CPU which is
handling interrupts.
But the check is done against the state index returned by the back
end driver's ->enter functions which could be different from the
initial index passed as parameter to the cpuidle_enter_state()
function.
if (!cpuidle_state_is_coupled(drv, entered_state))
local_irq_enable();
[ ... ]
If the 'index' is referring to a coupled idle state but the
'entered_state' is *not* coupled, then the interrupts are enabled
again. All CPUs blocked on the sync barrier may busy loop longer
if the CPU has interrupts to handle before decrementing the
ready-count. That's consuming more energy than saving.
Fixes: 0b89e9aa2856 (cpuidle: delay enabling interrupts until all coupled CPUs leave idle) Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ rjw: Subject & changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the 'registered' member of the cpuidle_device struct is set
to 1 during cpuidle_register_device. In this same function there are
checks to see if the device is already registered to prevent duplicate
calls to register the device, but this value is never set to 0 even on
unregister of the device. Because of this, any attempt to call
cpuidle_register_device after a call to cpuidle_unregister_device will
fail which shouldn't be the case.
To prevent this, set registered to 0 when the device is unregistered.
Fixes: c878a52d3c7c (cpuidle: Check if device is already registered) Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As pm_runtime_set_active() may fail because the device's parent isn't
active, we can end up executing the ->runtime_resume() callback for the
device when it isn't allowed.
Fix this by invoking pm_runtime_set_active() before running the callback
and let's also deal with the error code.
GPIO lookup tables are supposed to be zero terminated. Let's do that
and avoid accidentally walking off the end.
Fixes: 61dd2ca2d44e ("mfd: intel_soc_pmic_core: Add lookup table for Panel Control as GPIO signal") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All configurations are lost and the registers will have
default values when the hardware is suspended and resumed,
so saving the private register space context on suspend, and
restoring it on resume.
Fixes: 4b45efe85263 (mfd: Add support for Intel Sunrisepoint LPSS devices) Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ads7828 the internal reference defaults to off upon power up. When
using internal reference, it needs to be turned on and the voltage needs
to settle before normal conversion cycle can be started. Hence perform a
dummy read in the probe to enable the internal reference allowing the
voltage to settle before performing a normal read.
Without this fix, the first read from the ADC when using internal
reference always returns incorrect data.
When KDUMP is triggered the driver first talks to the firmware in INTX
mode, but the adapter firmware is still in MSIX mode. Therefore the first
driver command hangs since the driver is waiting for an INTX response and
firmware gives a MSIX response. If when the OS is installed on a RAID
drive created by the adapter KDUMP will hang since the driver does not
receive a response in sync mode.
Fixed by: Change the firmware to INTX mode if it is in MSIX mode before
sending the first sync command.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.
In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.
The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.
Fixed by: Adding another kthread_should_stop() before schedule_timeout() Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
aac_fib_send has a special function case for initial commands during
driver initialization using wait < 0(pseudo sync mode). In this case,
the command does not sleep but rather spins checking for timeout.This
loop is calls cpu_relax() in an attempt to allow other processes/threads
to use the CPU, but this function does not relinquish the CPU and so the
command will hog the processor. This was observed in a KDUMP
"crashkernel" and that prevented the "command thread" (which is
responsible for completing the command from being timed out) from
starting because it could not get the CPU.
Fixed by replacing "cpu_relax()" call with "schedule()" Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't use kfree_skb in irq disable context, because spin_lock_irqsave
make sure we are always in irq disable context, use dev_kfree_skb_irq
instead of kfree_skb is better than dev_kfree_skb_any.
Signed-off-by: Wang YanQing <udknight@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and
rtl_lps_enter() to use work queue"), the tests for enter/exit
power-save mode were inverted. With this change applied, the
wifi connection becomes much more stable.
Fixes: a269913c52ad ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue") Signed-off-by: Wang YanQing <udknight@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous patch added an option to rtl8723be to manually select the
antenna for those cases when only a single antenna is present, and the
on-board EEPROM is incorrectly programmed. This patch implements the
necessary changes in the Bluetooth coexistence driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A number of new laptops have been delivered with only a single antenna.
In principle, this is OK; however, a problem arises when the on-board
EEPROM is programmed to use the other antenna connection. The option
of opening the computer and moving the connector is not always possible
as it will void the warranty in some cases. In addition, this solution
breaks the Windows driver when the box dual boots Linux and Windows.
A fix involving a new module parameter has been developed. This commit
adds the new parameter and implements the changes needed for the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of timeout during read operation, the exit path lacked PM
runtime put. This could lead to unbalanced runtime PM usage counter thus
leaving the device in an active state.
Fixes: d7fd6075a205 ("hwrng: exynos - Add timeout for waiting on init done") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BugLink: http://bugs.launchpad.net/bugs/972604
Commit 09c9bae26b0d3c9472cb6ae45010460a2cee8b8d ("ath5k: add led pin
configuration for compaq c700 laptop") added a pin configuration for the Compaq
c700 laptop. However, the polarity of the led pin is reversed. It should be
red for wifi off and blue for wifi on, but it is the opposite. This bug was
reported in the following bug report:
http://pad.lv/972604
Fixes: 09c9bae26b0d3c9472cb6ae45010460a2cee8b8d ("ath5k: add led pin configuration for compaq c700 laptop") Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is observed that while loading and unloading ath10k modules
in an infinite loop, before ath10k_core_start() completion HTT
rx frames are received, while processing these frames,
dereferencing the arvifs list code is getting hit before
initilizing the arvifs list, causing a kernel panic.
This patch initilizes the arvifs list before initilizing htt.
Upon firmware assert, restart work will be triggered so that mac80211
will reconfigure the driver. An issue is reported that after restart
work, survey dump data do not contain in-use (SURVEY_INFO_IN_USE) info
for operating channel. During reconfigure, since mac80211 already has
valid channel context for given radio, channel context iteration return
num_chanctx > 0. Hence rx_channel is always NULL. Fix this by assigning
channel context to rx_channel when driver restart is in progress.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 166de3f1895d ("ath10k: remove supported chain mask") had revealed
an issue on monitor mode. Configuring NSS upon monitor interface
creation is causing target assert in all qca9888x and qca6174 firmware.
Firmware assert issue can be reproduced by below sequence even after
reverting commit 166de3f1895d ("ath10k: remove supported chain mask").
ip link set wlan0 down
iw wlan0 set type monitor
iw phy0 set antenna 7
ip link set wlan0 up
This issue is originally reported on qca9888 with 10.1 firmware.
Fixes: 5572a95b4b ("ath10k: apply chainmask settings to vdev on creation") Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is observed that, we are disabling the packet log if we write same
value to the pktlog_filter for the second time. Always enable pktlogs
on non zero filter.
Fixes: 90174455ae05 ("ath10k: add support to configure pktlog filter") Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new element got inserted into enum mx35_clks with commit 3713e3f5e927
("clk: imx35: define two clocks for rtc"). This insertion shifted most
nummerical clock assignments to a new nummerical value which in turn
rendered most hardcoded nummeric values in imx35.dtsi incorrect.
Restore the existing order by moving the newly introduced clock to the
end of the enum. Update the dts documentation accordingly.
Signed-off-by: Alexander Kurz <akurz@blala.de> Fixes: 3713e3f5e927 ("clk: imx35: define two clocks for rtc") Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log