Linus Torvalds [Thu, 26 Jun 2014 20:06:13 +0000 (13:06 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A small collection of fixes/changes for the current series. This
contains:
- Removal of dead code from Gu Zheng.
- Revert of two bad fixes that went in earlier in this round, marking
things as __init that were not purely used from init.
- A fix for blk_mq_start_hw_queue() using the __blk_mq_run_hw_queue(),
which could place us wrongly. Make it use the non __ variant,
which handles cases where we are called from the wrong CPU set.
From me.
- A fix for drbd, which allocates discard requests without room for
the SCSI payload. From Lars Ellenberg.
- A fix for user-after-free in the blkcg code from Tejun.
- Addition of limiting gaps in SG lists, if the hardware needs it.
This is the last pre-req patch for blk-mq to enable the full NVMe
conversion. Could wait until 3.17, but it's simple enough so would
be nice to have everything we need for the NVMe port in the 3.17
release. From me"
* 'for-linus' of git://git.kernel.dk/linux-block:
drbd: fix NULL pointer deref in blk_add_request_payload
blk-mq: blk_mq_start_hw_queue() should use blk_mq_run_hw_queue()
block: add support for limiting gaps in SG lists
bio: remove unused macro bip_vec_idx()
Revert "block: add __init to elv_register"
Revert "block: add __init to blkcg_policy_register"
blkcg: fix use-after-free in __blkg_release_rcu() by making blkcg_gq refcnt an atomic_t
floppy: format block0 read error message properly
Al Viro [Mon, 23 Jun 2014 07:44:40 +0000 (08:44 +0100)]
Fix 32-bit regression in block device read(2)
blkdev_read_iter() wants to cap the iov_iter by the amount of data
remaining to the end of device. That's what iov_iter_truncate() is for
(trim iter->count if it's above the given limit). So far, so good, but
the argument of iov_iter_truncate() is size_t, so on 32bit boxen (in
case of a large device) we end up with that upper limit truncated down
to 32 bits *before* comparing it with iter->count.
Easily fixed by making iov_iter_truncate() take 64bit argument - it does
the right thing after such change (we only reach the assignment in there
when the current value of iter->count is greater than the limit, i.e.
for anything that would get truncated we don't reach the assignment at
all) and that argument is not the new value of iter->count - it's an
upper limit for such.
The overhead of passing u64 is not an issue - the thing is inlined, so
callers passing size_t won't pay any penalty.
Reported-and-tested-by: Theodore Tso <tytso@mit.edu> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Tested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk> Tested-by: Bruno Wolff III <bruno@wolff.to> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* patchwork: (11415 commits)
[media] technisat-sub2: Fix stream curruption on high bitrate
[media] au0828: don't hardcode height/width
[media] au0828: Only alt setting logic when needed
[media] au0828/au8522: Add PAL-M support
[media] au8522: Fix demod analog mode setting
[media] au8522: cleanup s-video settings at setup_decoder_defaults()
[media] au8522: be sure that we'll setup audio routing at the right time
[media] au8522: be sure that the setup will happen at streamon time
[media] au8522: move input_mode out one level
[media] au0828: add missing tuner Kconfig dependency
[media] rc: img-ir: Expand copyright headers with GPL notices
[media] V4L2: soc_camera: Add run-time dependencies to sh_mobile drivers
[media] media: mx2_camera: Change Kconfig dependency
[media] media: mx1_camera: Remove driver
[media] V4L2: soc_camera: add run-time dependencies to R-Car VIN driver
[media] rcar_vin: copy flags from pdata
[media] V4L: soc-camera: explicitly free allocated managed memory on error
[media] dib7000p: Callibrate signal strength
[media] dib7000p: Add DVBv5 stats support
[media] dib8000: export just one symbol
...
* v4l_for_linus:
[media] saa7134: use unlocked_ioctl instead of ioctl
[media] media: v4l2-core: v4l2-dv-timings.c: Cleaning up code wrong value used in aspect ratio
[media] si2168: firmware download fix
[media] si2157: add one missing parenthesis
[media] si2168: add one missing parenthesis
[media] staging: tighten omap4iss dependencies
[media] au0828-dvb: restore its permission to 644
Bob Peterson [Thu, 26 Jun 2014 14:47:48 +0000 (10:47 -0400)]
GFS2: Allow caching of glocks for flock
This patch removes the GLF_NOCACHE flag from the glocks associated with
flocks. There should be no good reason not to cache glocks for flocks:
they only force the glock to be demoted before they can be reacquired,
which can slow down performance and even cause glock hangs, especially
in cases where the flocks are held in Shared (SH) mode.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Bob Peterson [Thu, 26 Jun 2014 14:46:25 +0000 (10:46 -0400)]
GFS2: Allow flocks to use normal glock dq rather than dq_wait
This patch allows flock glocks to use a non-blocking dequeue rather
than dq_wait. It also reverts the previous patch I had posted regarding
dq_wait. The reverted patch isn't necessarily a bad idea, but I decided
this might avoid unforeseen side effects, and was therefore safer.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Al Viro [Thu, 26 Jun 2014 16:31:13 +0000 (12:31 -0400)]
[regression] fix 32-bit breakage in block device read(2)
blkdev_read_iter() wants to cap the iov_iter by the amount of
data remaining to the end of device. That's what iov_iter_truncate()
is for (trim iter->count if it's above the given limit). So far,
so good, but the argument of iov_iter_truncate() is size_t, so on
32bit boxen (in case of a large device) we end up with that upper
limit truncated down to 32 bits *before* comparing it with iter->count.
Easily fixed by making iov_iter_truncate() take 64bit argument -
it does the right thing after such change (we only reach the
assignment in there when the current value of iter->count is greater
than the limit, i.e. for anything that would get truncated we don't
reach the assignment at all) and that argument is not the new
value of iter->count - it's an upper limit for such.
The overhead of passing u64 is not an issue - the thing is inlined,
so callers passing size_t won't pay any penalty.
Jan Kara [Thu, 26 Jun 2014 16:30:54 +0000 (12:30 -0400)]
ext4: Fix hole punching for files with indirect blocks
Hole punching code for files with indirect blocks wrongly computed
number of blocks which need to be cleared when traversing the indirect
block tree. That could result in punching more blocks than actually
requested and thus effectively cause a data loss. For example:
Jan Kara [Thu, 26 Jun 2014 16:28:57 +0000 (12:28 -0400)]
ext4: Fix block zeroing when punching holes in indirect block files
free_holes_block() passed local variable as a block pointer
to ext4_clear_blocks(). Thus ext4_clear_blocks() zeroed out this local
variable instead of proper place in inode / indirect block. We later
zero out proper place in inode / indirect block but don't dirty the
inode / buffer again which can lead to subtle issues (some changes e.g.
to inode can be lost).
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Namjae Jeon [Thu, 26 Jun 2014 14:11:53 +0000 (10:11 -0400)]
ext4: decrement free clusters/inodes counters when block group declared bad
We should decrement free clusters counter when block bitmap is marked
as corrupt and free inodes counter when the allocation bitmap is
marked as corrupt to avoid misunderstanding due to incorrect available
size in statfs result. User can get immediately ENOSPC error from
write begin without reaching for the writepages.
Cc: Darrick J. Wong<darrick.wong@oracle.com> Reported-by: Amit Sahrawat <amit.sahrawat83@gmail.com> Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com> Signed-off-by: Ashish Sangwan <a.sangwan@samsung.com>
For Intel Haswell/Broadwell display HD-A controller, the 24MHz HD-A link BCLK
is converted from Core Display Clock (CDCLK): BCLK = CDCLK * M / N
And there are two registers EM4 and EM5 to program M, N value respectively.
The EM4/EM5 values will be lost and when the display power well is disabled.
BIOS programs CDCLK selected by OEM and EM4/EM5, but BIOS has no idea about
display power well on/off at runtime. So the M/N can be wrong if non-default
CDCLK is used when the audio controller resumes, which results in an invalid
BCLK and abnormal audio playback rate. So this patch saves and restores valid
M/N values on controller suspend/resume.
And 'struct hda_intel' is defined to contain standard HD-A 'struct azx' and
Intel specific fields, as Takashi suggested.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ralf Baechle [Thu, 26 Jun 2014 13:43:01 +0000 (14:43 +0100)]
MIPS: Lasat: Fix build error if CRC32 is not enabled.
Kconfig doesn't select CRC32 so it's possible to build a Lasat kernel
without CONFIG_CRC32 resulting in a build error:
LD vmlinux
arch/mips/built-in.o: In function `lasat_init_board_info':
(.text+0x22c): undefined reference to `crc32_le'
arch/mips/built-in.o: In function `lasat_write_eeprom_info':
(.text+0x7fc): undefined reference to `crc32_le'
make: *** [vmlinux] Error 1
Markos Chandras [Mon, 23 Jun 2014 08:48:51 +0000 (09:48 +0100)]
MIPS: MSC: Prevent out-of-bounds writes to MIPS SC ioremap'd region
Previously, the lower limit for the MIPS SC initialization loop was
set incorrectly allowing one extra loop leading to writes
beyond the MSC ioremap'd space. More precisely, the value of the 'imp'
in the last loop increased beyond the msc_irqmap_t boundaries and
as a result of which, the 'n' variable was loaded with an incorrect
value. This value was used later on to calculate the offset in the
MSC01_IC_SUP which led to random crashes like the following one:
CPU 0 Unable to handle kernel paging request at virtual address e75c0200,
epc == 8058dba4, ra == 8058db90
[...]
Call Trace:
[<8058dba4>] init_msc_irqs+0x104/0x154
[<8058b5bc>] arch_init_irq+0xd8/0x154
[<805897b0>] start_kernel+0x220/0x36c
Kernel panic - not syncing: Attempted to kill the idle task!
Markos Chandras [Mon, 23 Jun 2014 09:39:00 +0000 (10:39 +0100)]
MIPS: bpf: Fix stack space allocation for BPF memwords on MIPS64
When allocating stack space for BPF memwords we need to use the
appropriate 32 or 64-bit instruction to avoid losing the top 32 bits
of the stack pointer.
The fix is to look for 7<<5 on big-endian systems for the pkt_type
field, and shift by 5 so the packet type will be at the lower 3 bits
of the A register.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: David S. Miller <davem@davemloft.net> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: netdev@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7132/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Wed, 25 Jun 2014 08:37:21 +0000 (09:37 +0100)]
MIPS: BPF: Prevent kernel fall over for >=32bit shifts
Remove BUG_ON() if the shift immediate is >=32 to avoid kernel crashes
due to malicious user input. If the shift immediate is >= 32,
we simply load the destination register with 0 since only
32-bit instructions are used by JIT so this will do the
correct thing even on MIPS64.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: David S. Miller <davem@davemloft.net> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: netdev@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7179/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:56 +0000 (10:38 +0100)]
MIPS: bpf: Drop update_on_xread and always initialize the X register
Previously, update_on_xread() only set the reset flag if SEEN_X hasn't
been set already. However, SEEN_X is used to indicate that X is used
as destination or source register so there are some cases where X
is only used as source register and we really need to make sure that it
has been initialized in time. As a result of which, drop this function and
always set X to zero if it's used in any of the opcodes.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: David S. Miller <davem@davemloft.net> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: netdev@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7133/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:55 +0000 (10:38 +0100)]
MIPS: bpf: Fix is_range() semantics
is_range() was meant to check whether the number is within
the s16 range or not. However the return values and consumers expected
the exact opposite. We fix that by inverting the logic in the function
to return 'true' for < s16 and 'false' for > s16.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Reported-by: Alexei Starovoitov <ast@plumgrid.com> Cc: David S. Miller <davem@davemloft.net> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: netdev@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7131/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:52 +0000 (10:38 +0100)]
MIPS: bpf: Use correct mask for VLAN_TAG case
Using VLAN_VID_MASK is not correct to get the vlan tag. Use
~VLAN_PRESENT_MASK instead and make sure it's u16 so the top 16-bits
will be removed. This will ensure that the emit_andi() code will not
treat this as a big 32-bit unsigned value.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: David S. Miller <davem@davemloft.net> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: netdev@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7127/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:51 +0000 (10:38 +0100)]
MIPS: bpf: Fix branch conditional for BPF_J{GT/GE} cases
The sltiu and sltu instructions will set the scratch register
to 1 if A <= X|K so fix the emitted branch conditional to check
for scratch != zero rather than scratch >= zero which would complicate
the resuling branch logic given that MIPS does not have a BGT or BGET
instructions to compare general purpose registers directly.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: David S. Miller <davem@davemloft.net> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: netdev@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7126/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:49 +0000 (10:38 +0100)]
MIPS: bpf: Use 'andi' instead of 'and' for the VLAN cases
The VLAN_VID_MASK and VLAN_TAG_PRESENT are immediates, so using
'and' which expects 3 registers will produce wrong results. Fix
this by using the 'andi' instruction.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: David S. Miller <davem@davemloft.net> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: netdev@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7124/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Markos Chandras [Mon, 23 Jun 2014 09:38:48 +0000 (10:38 +0100)]
MIPS: bpf: Return error code if the offset is a negative number
Previously, the negative offset was not checked leading to failures
due to trying to load data beyond the skb struct boundaries. Until we
have proper asm helpers in place, it's best if we return ENOSUPP if K
is negative when trying to JIT the filter or 0 during runtime if we
do an indirect load where the value of X is unknown during build time.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com> Cc: David S. Miller <davem@davemloft.net> Cc: Daniel Borkmann <dborkman@redhat.com> Cc: Alexei Starovoitov <ast@plumgrid.com> Cc: netdev@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7123/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit d6b3314b49e12e8c349deb4ca28e7028db00728f "MIPS: uasm: Add lh uam
instruction" added the 'lh' micro-assembler instruction but it used the
'lw' opcode for it. Fix it by using the correct 'lh' opcode.
Alex Smith [Tue, 17 Jun 2014 09:39:53 +0000 (10:39 +0100)]
recordmcount/MIPS: Fix possible incorrect mcount_loc table entries in modules
On MIPS calls to _mcount in modules generate 2 instructions to load
the _mcount address (and therefore 2 relocations). The mcount_loc
table should only reference the first of these, so the second is
filtered out by checking the relocation offset and ignoring ones that
immediately follow the previous one seen.
However if a module has an _mcount call at offset 0, the second
relocation would not be filtered out due to old_r_offset == 0
being taken to mean that the current relocation is the first one
seen, and both would end up in the mcount_loc table.
This results in ftrace_make_nop() patching both (adjacent)
instructions to branches over the _mcount call sequence like so:
The second branch is in the delay slot of the first, which is
defined to be unpredictable - on the platform on which this bug was
encountered, it triggers a reserved instruction exception.
Fix by initializing old_r_offset to ~0 and using that instead of 0
to determine whether the current relocation is the first seen.
Signed-off-by: Alex Smith <alex.smith@imgtec.com> Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7098/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Daniel Borkmann [Tue, 17 Jun 2014 10:16:18 +0000 (12:16 +0200)]
MIPS: BPF JIT: Fix build error.
mips: allmodconfig fails in 3.16-rc1 with lots of undefined symbols.
arch/mips/net/bpf_jit.c: In function 'is_load_to_a':
arch/mips/net/bpf_jit.c:559:7: error: 'BPF_S_LD_W_LEN' undeclared (first use in this function)
arch/mips/net/bpf_jit.c:559:7: note: each undeclared identifier is reported only once for each function it appears in
arch/mips/net/bpf_jit.c:560:7: error: 'BPF_S_LD_W_ABS' undeclared (first use in this function)
[...]
The reason behind this is that 3480593131e0 ("net: filter: get rid of
BPF_S_* enum") was routed via net-next tree, that takes all BPF-related
changes, at a time where MIPS BPF JIT was not part of net-next, while c6610de353da ("MIPS: net: Add BPF JIT") was routed via mips arch tree
and went into mainline within the same merge window. Thus, fix it up by
converting BPF_S_* in a similar fashion as in 3480593131e0 for MIPS.
Paul Burton [Wed, 18 Jun 2014 14:00:46 +0000 (15:00 +0100)]
Revert "MIPS: Save/restore MSA context around signals"
This reverts commit eec43a224cf1 "MIPS: Save/restore MSA context around
signals" and the MSA parts of ca750649e08c "MIPS: kernel: signal:
Prevent save/restore FPU context in user memory" (the restore path of
which appears incorrect anyway...).
The reverted patch took care not to break compatibility with userland
users of struct sigcontext, but inadvertantly changed the offset of the
uc_sigmask field of struct ucontext. Thus Linux v3.15 breaks the
userland ABI. The MSA context will need to be saved via some other
opt-in mechanism, but for now revert the change to reduce the fallout.
This will have minimal impact upon use of MSA since the only supported
CPU which includes it (the P5600) is 32-bit and therefore requires that
the experimental CONFIG_MIPS_O32_FP64_SUPPORT Kconfig option be selected
before the kernel will set FR=1 for a task, a requirement for MSA use.
Thus the users of MSA are limited to known small groups of people & this
patch won't be breaking any previously working MSA-using userland
outside of experimental settings.
[ralf@linux-mips.org: Fixed rejects.]
Cc: stable@vger.kernel.org Reported-by: Joseph S. Myers <joseph@codesourcery.com> Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7107/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Takashi Iwai [Wed, 25 Jun 2014 12:24:47 +0000 (14:24 +0200)]
ALSA: usb-audio: Fix races at disconnection and PCM closing
When a USB-audio device is disconnected while PCM is still running, we
still see some race: the disconnect callback calls
snd_usb_endpoint_free() that calls release_urbs() and then kfree()
while a PCM stream would be closed at the same time and calls
stop_endpoints() that leads to wait_clear_urbs(). That is, the EP
object might be deallocated while a PCM stream is syncing with
wait_clear_urbs() with the same EP.
Basically calling multiple wait_clear_urbs() would work fine, also
calling wait_clear_urbs() and release_urbs() would work, too, as
wait_clear_urbs() just reads some fields in ep. The problem is the
succeeding kfree() in snd_pcm_endpoint_free().
This patch moves out the EP deallocation into the later point, the
destructor callback. At this stage, all PCMs must have been already
closed, so it's safe to free the objects.
Reported-by: Alan Stern <stern@rowland.harvard.edu> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tadeusz Struk [Tue, 24 Jun 2014 22:19:40 +0000 (15:19 -0700)]
crypto: qat - Fix error path crash when no firmware is present
Firmware loader crashes when no firmware file is present.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tadeusz Struk [Tue, 24 Jun 2014 22:19:34 +0000 (15:19 -0700)]
crypto: qat - Fixed new checkpatch warnings
After updates to checkpatch new warnings pops up this patch fixes them.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Acked-by: Tadeusz Struk <tadeusz.struk@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
projects / karo-tx-linux.git / log