carl9170: reinit phy after HT settings have changed
The driver has a set of different initvals for 20 MHz
vs dynamic HT2040 operation. Because we can't change
some of the registers "in-flight", the driver needs to
perform a warm reset.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't mark the device as completely dead just yet.
If all goes to plan and carl9170_reboot succeeds
then we can skip the expensive userspace-driven
reinitialization anyway.
And if it doesn't and carl9170_reboot fails,
then carl9170_usb_cancel_urbs will do the
necessary steps.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since carl9170 gained support to read the noisefloor,
the reported noisefloor level was pretty poor.
Initially I assumed that something was wrong in the PHY
setup and it would be impossible to fix without any
guidances. But this was not the case. In fact the nf
readings were correct and the thing that was broken
was the "simple" sign extension code!
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Fri, 17 Sep 2010 02:37:12 +0000 (11:37 +0900)]
ath5k: Simplify cw_min/max and AIFS configuration
Get rid of overly complicated cw_min/max and AIFS configuration:
* Validate values in ath5k_hw_set_tx_queueprops(), so we can use them directly
without further checks or computation in ath5k_hw_reset_tx_queue().
* Simplifiy by using AR5K_TUNE_AIFS|CWMIN|CWMAX variables directly since we
don't support XR or B channels. That way we can also remove
AR5K_TXQ_USEDEFAULT and the confusing logic around it.
* Update data types: AIFS is u8, CW's are u16.
* Remove now unneeded variables in ath5k_hw.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Fri, 17 Sep 2010 02:37:07 +0000 (11:37 +0900)]
ath5k: Keep last descriptor in queue
If we return a TX descriptor to the pool of available descriptors, while a
queues TXDP still points to it we could potentially run into all sorts of
troube.
It has been suggested that there is hardware which can set the descriptors
done bit before it reads ds_link and moves on to the next descriptor. While the
documentation says this is not true for newer chipsets (the descriptor contents
are copied to some internal memory), we don't know about older hardware.
To be safe, we always keep the last descriptor in the queue, and avoid dangling
TXDP pointers. Unfortunately this does not fully resolve the problem - queues
still get stuck!
This is similar to what ath9k does.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Fri, 17 Sep 2010 02:36:56 +0000 (11:36 +0900)]
ath5k: Add watchdog for stuck TX queues
Since we do not know any better solution to the problem that TX queues can get
stuck, this adds a timer-based watchdog, which will check for stuck queues and
reset the hardware if necessary.
Bruno Randolf [Fri, 17 Sep 2010 02:36:35 +0000 (11:36 +0900)]
ath5k: Use four hardware queues
Prepare ath5k for WME by using four hardware queues.
The way we set up our queues matches the mac80211 queue priority 1:1, so we
don't have to do any mapping for queue numbers.
Every queue uses 50 of the total 200 available transmit buffers, so the DMA
memory usage does not increase with this patch, but it might be good to
fine-tune the number of buffers per queue later (depending on the CPU speed and
load, and the speed of the medium access, it might not be big enough).
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bob Copeland [Fri, 17 Sep 2010 03:45:07 +0000 (12:45 +0900)]
ath5k: reorder base.c to remove fwd decls
This change reorganizes the main ath5k file in order to re-group
related functions and remove most of the forward declarations
(from 61 down to 3). This is, unfortunately, a lot of churn, but
there should be no functional changes.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unneeded ath_crypt_caps flags, as per "ath9k_hw: remove useless hw
capability flags" (364734fafbba0c3133e482db78149b9a823ae7a5), but set the
AESCCM flag for ath9k. common ath code still needs a flag for this because
there is ath5k hardware which can't do AES in hardware.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a simple mechanism to pass platform data to the
SDIO instances of wl12xx.
This way there is no confusion over who owns the 'embedded data',
typechecking is preserved, and no possibility for the wrong driver to
pick up the data.
Originally proposed by Russell King.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make it possible for the set power method to indicate a
success/failure return value. This is needed to support
more complex power on/off operations such as SDIO
power manipulations.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Acked-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jay Sternberg [Wed, 8 Sep 2010 16:42:35 +0000 (09:42 -0700)]
iwlwifi: corrections to debug output of ucode statistics
remove duplicate header and clean up format so it is defined once
making changes consolicated ensuring consistancy of output.
no function change to date displayed.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Sun, 5 Sep 2010 17:49:42 +0000 (10:49 -0700)]
iwlagn: keep track of failure tx status
Tx command response sent to host by uCode after completed
the transmission attempt. The status parameter indicates
whether the transmission was successful, or else why if failed.
Here we keep the counters to help understand the different failure
cases.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The patch titled "ath9k: Add new file init.c" shuffled some code
around but in dong so for some reason also removed the revision
check for disablign power save. Add this revision check again
so we can get power save re-enabled again by default on cards
newer than AR5416 and AR5418.
This patch has fixes for stable kernels [2.6.34+].
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helper only clears the SC_OP_WAIT_FOR_{BEACON,CAB} flags.
Remove it and clear these flags directly in the approptiate
places instead.
Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
introduced a regression which forgot to lift the beacon flag
after we received all broadcast and multicast data. This meant
we never went to sleep consuming about ~650mW on idle. This pretty
much broke power save completely.
This patch has fixes for stable kernels [2.6.32+].
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Sameer Nanda <snanda@google.com> Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some buggy APs do not respond to unicast probe requests
or send unicast probe requests very delayed so in the
worst case we should try to send broadcast probe requests,
otherwise we can get disconnected from these APs.
Even if drivers do not have filters to disregard probe
responses from foreign APs mac80211 will only process
probe responses from our associated AP for re-arming
connection monitoring.
We need to do this since the beacon monitor does not
push back the connection monitor by design so even if we
are getting beacons from these type of APs our connection
monitor currently relies heavily on the way the probe
requests are received on the AP. An example of an AP
affected by this is the Nexus One, but this has also been
observed with random APs.
We can probably optimize this later by using null funcs
instead of probe requests.
This patch has fixes for stable kernels [2.6.35+].
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: disable beacon monitor while going offchannel
The beacon monitor should be disabled when going off channel
to prevent spurious warnings and triggering connection
deterioration work such as sending probe requests. Re-enable
the beacon monitor once we come back to the home channel.
This patch has fixes for stable kernels [2.6.34+].
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: make the beacon monitor available externally
This will be used by other components next. The beacon
monitor was added as of 2.6.34 so these fixes are applicable
only to kernels >= 2.6.34.
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: reset connection idle when going offchannel
When we go offchannel mac80211 currently leaves alive the
connection idle monitor. This should be instead postponed
until we come back to our home channel, otherwise by the
time we get back to the home channel we could be triggering
unecesary probe requests. For APs that do not respond to
unicast probe requests (Nexus One is a simple example) this
means we essentially get disconnected after the probes
fails.
This patch has stable fixes for kernels [2.6.35+]
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: reset probe send counter upon connection timer reset
Upon beacon loss we send probe requests after 30 seconds of idle
time and we wait for each probe response 1/2 second. We send a
total of 3 probe requests before giving up on the AP. In the case
that we reset the connection idle monitor we should reset the probe
requests count to 0. Right now this won't help in any way but
the next patch will.
This patch has fixes for stable kernel [2.6.35+].
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: add helper for reseting the connection monitor
This will be used in another place later. The connection
monitor was added as of 2.6.35 so these fixes will be
applicable to >= 2.6.35.
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k: fix enabling ANI / tx monitor after bg scan
ath9k's entire logic with SC_OP_SCANNING is incorrect due to the
way mac80211 currently implements the scan complete callback and
we handle it in ath9k. This patch removes the flag completely in
preference for the SC_OP_OFFCHANNEL which is really what we wanted.
The scanning flag was used to ensure we reset ANI to the old values
when we go back to the home channel, but if we are offchannel we
use some defaults. The flag was also used to re-enable the TX monitor.
Without this patch we simply never re-enabled ANI and the TX monitor
after going offchannel. This means that after one background
scan we are prone to noise issues and if we had a TX hang we would
not recover. To get this to work properly we must enable ANI after
we have configured the beacon timers, otherwise hardware acts really
oddly.
This patch has stable fixes which apply down to [2.6.36+], there
*may* be a to fix this on older kernels but requires a bit of
work since this patch relies on the new mac80211 flag
IEEE80211_CONF_OFFCHANNEL which was introduced as of 2.6.36.
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we return to the home channel we were never reseting our beacon
timers, this was casued by the fact that the scanning flag was still
on even after we returned to our home channel. There are also other
reasons why we would get a reset and if we are not off channel
we always need to resynch our beacon timers, because a reset will
clear them.
This bug is a regression introduced on 2.6.36. The order of the
changes are as follows:
So 5ee08656 would have worked if a0daa0e7 was not committed but
it was so this means 5ee08656 was broken since it assumed that
when we were in the channel change routine the scan flag would
be lifted. As it turns out the scan flag will be set when we
are already on the home channel.
These issues will need to be considered for our solution on
reshifting the scan complete callback location on mac80211 on
current development kernel work.
This patch has stable fixes which apply down to [2.6.36+]
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k has a race on putting the chip into network sleep and
having registers read from hardware. The race occurs because
although ath9k_ps_restore() locks its own callers it makes use
of some variables which get altered in the driver at different
code paths. The variables are the ps_enabled and ps_flags.
This is easily reprodicible in large network environments when
roaming with the wpa_supplicant simple bgscan. You'd get some
0xdeadbeef read out on certain registers such as:
ath: timeout (100000 us) on reg 0x806c: 0xdeadbeef & 0x01f00000 != 0x00000000
ath: RX failed to go idle in 10 ms RXSM=0xdeadbeef
The fix is to protect the ath9k_config(hw, IEEE80211_CONF_CHANGE_PS)
calls with a spin_lock_irqsave() which will disable contendors for
these variables from interrupt context, timers, re-entry from mac80211
on the same callback, and most importantly from ath9k_ps_restore()
which is the only call which will put the device into network sleep.
There are quite a few threads and bug reports on these a few of them are:
Cc: stable@kernel.org Cc: Paul Stewart <pstew@google.com> Cc: Amod Bodas <amod.bodas@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
To optimize register read/write operations, the HTC firmwares were patched
to change EP3 and EP4 pipe types from Interrupt to Bulk. So register writes
are submitted as bulk urbs, but register reads are not. Also changing the
register read endpoint pipe as bulk type when URBs are filled improves the
register reads considerably which results in reduced scan time and CPU
utilization.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 16 Sep 2010 12:58:23 +0000 (14:58 +0200)]
mac80211: add p2p device type support
When a driver advertises p2p device support,
mac80211 will handle it, but internally it will
rewrite the interface type to STA/AP rather than
P2P-STA/GO since otherwise a lot of paths need
to be touched that are otherwise identical. A
p2p boolean tells drivers whether or not a given
interface will be used for p2p or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: remove warning in ath9k_hw_def_get_num_ant_config
This patch fixes following warning
drivers/net/wireless/ath/ath9k/eeprom_def.c: In function 'ath9k_hw_def_get_num_ant_config'
drivers/net/wireless/ath/ath9k/eeprom_def.c:1425:47: warning: comparison
between 'enum ath9k_hal_freq_band' and 'enum ieee80211_band'
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 15 Sep 2010 19:26:13 +0000 (15:26 -0400)]
ath9k: make ath_ant_div_conf_fast_divbias static
CHECK drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/ath/ath9k/recv.c:1341:6: warning: symbol 'ath_ant_div_conf_fast_divbias' was not declared. Should it be static?
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 15 Sep 2010 19:16:22 +0000 (15:16 -0400)]
iwlwifi: fix sparse warning about wrong enum for band parameter
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27: int enum nl80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:386:27: int enum ieee80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57: int enum ieee80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:435:57: int enum nl80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53: int enum ieee80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:474:53: int enum nl80211_band
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72: warning: mixing different enum types
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72: int enum ieee80211_band versus
drivers/net/wireless/iwlwifi/iwl-scan.c:588:72: int enum nl80211_band
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 15 Sep 2010 13:13:13 +0000 (15:13 +0200)]
mac80211: set running state earlier
When an interface is brought up, the recent changes
to allow changing type-while-up only set the running
bit after everything was done. This broke a number
of things, including idle calculation for monitor
interfaces, and it also broke WDS station insertion
(although nobody noticed yet).
Thus, change the code to set the running bit earlier,
but keep it after the driver's add_interface was
called because otherwise drivers may iterate over
interfaces they haven't fully set up yet.
Reported-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 15 Sep 2010 11:28:15 +0000 (13:28 +0200)]
cfg80211/mac80211: use lockdep_assert_held
Instead of using a WARN_ON(!mutex_is_locked())
use lockdep_assert_held() which compiles away
completely when lockdep isn't enabled, and
also is a more accurate assertion since it
checks that the current thread is holding the
mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 14 Sep 2010 20:06:53 +0000 (22:06 +0200)]
mac80211: use correct station flags lock
This code is modifying the station flags, and
as such should hold the flags lock so it can
do so atomically vs. other flags modifications
and readers. This issue was introduced when
this code was added in eccb8e8f, as it used
the wrong lock (thus not fixing the race that
was previously documented in a comment.)
Cc: stable@kernel.org [2.6.31+] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 8 Sep 2010 07:04:43 +0000 (16:04 +0900)]
ath5k: Use common ath key management functions
Use common ath key management functions in ath5k. This fixes problems with HW
encryption in AP mode, which was broken in the ath5k implementation.
Before (with the ath5k implementation) only one client could connect to the AP
using HW encryption and WPA. When a second client connected, the first client
was not able to send/receive any more packets. Because of the problems with HW
encryption, software encryption was always used in AP mode, which resulted in a
high CPU load (and/or low thruput) on embedded devices. Instead of trying to
fix the implementation in ath5k it makes more sense to share the code with
ath9k.
This also enables HW encryption for AP mode again.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 8 Sep 2010 07:04:38 +0000 (16:04 +0900)]
ath: Copy key cache management functions from ath9k to ath
Copied the key cache management functions from ath9k (common.c and hw.c) to
ath/key.c so we can use them from ath5k, later.
Minor changes have been made:
- renamed ath9k_* to ath_*
- replaced ah->caps.keycache_size with common->keymax
- removed ATH9K_IS_MIC_ENABLED since it is always true.
- the AR_PCU_MIC_NEW_LOC_ENA flag is replaced with (splitmic == 0).
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 14 Sep 2010 20:26:44 +0000 (16:26 -0400)]
wl1271: remove warnings in wl1271_sdio_set_power
These were introduced in "wl1271: sdio: claim host only when doing IO"
drivers/net/wireless/wl12xx/wl1271_sdio.c: In function ‘wl1271_sdio_set_power’:
drivers/net/wireless/wl12xx/wl1271_sdio.c:193: warning: ‘return’ with a value, in function returning void
drivers/net/wireless/wl12xx/wl1271_sdio.c:195: warning: ‘return’ with a value, in function returning void
drivers/net/wireless/wl12xx/wl1271_sdio.c:186: warning: unused variable ‘func’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 14 Sep 2010 19:34:14 +0000 (21:34 +0200)]
mac80211: match only assigned bss in sta_info_get_bss
sta_info_get_bss() is used to match STA pointers
for VLAN/AP interfaces, but if the same station
is also added to multiple other interfaces it
will erroneously match because both pointers are
NULL, fix this by ignoring NULL pointers here.
Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 14 Sep 2010 16:37:19 +0000 (18:37 +0200)]
ath9k: fix BSSID mask calculation
At the time the .add_interface driver op is called, the interface has not
been marked as running yet, so ieee80211_iterate_active_interfaces will
not pass it to the iterator function.
Because of this, the calculated BSSID mask is wrong, which breaks multi-BSS
operation.
Additionally, the current way of comparing all addresses against each other
is pointless, as the hardware only uses the hardware MAC address and the BSSID
mask for matching the destination address, so all the address array
reallocation is completely unnecessary.
This patch simplifies the logic by setting the initial mask bytes to 0xff
and removing all bits in the iterator call that don't match the hardware MAC
address. It also calls the iterator for the vif that was passed to
add_interface()
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CPU consumption during the scan period is high, since
the register write go over Interrupt endpoint. On downloading
the firmware to the target, the USB descriptors are
'patched' to change the type of the endpoints from Interrupt
to Bulk.
With this fix, the CPU usage during a scan run comes down to
acceptable levels.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even is someone else complete scanning in mac80211, apply rxon and
tx power settings if gets scan complete notification from hardware.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace IWL_DEBUG_{INFO,HC,RC} to IWL_DEBUG_SCAN in iwl-scan.c file. Add
some more IWL_DEBUG_SCAN messages. This will allow to fully debug
scanning using only IWL_DL_SCAN flag.
Also start one message sentence with capital letter, since that
convention in iwl-scan.c file.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove redundant checks and use iwl_is_ready_rf().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: wait for scan work complete before restarting hw
This is needed to avoid warning in ieee80211_restart_hw about hardware
scan in progress.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we force scan complete at the end of iwl_scan_cancel_timeout
function. This cause race condition when we can get a new scan request
from mac80211 and complete it by iwl_bg_complete from older scan. Change
code to force scan complete only when really needed: device goes down,
interface is removed or scan timeout occurs.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: assure we complete scan in scan_abort and scan_check works
Assure we complete scan in mac80211 when we abort scanning (scan_abort
work) or scan timeout occurs (scan_check work). Currently
iwl_scan_cancel_timeout() procedure force scan finish in mac80211
at the end of timeout loop, so we can use it in proper work functions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we do not get notification from hardware about scan complete, after
timeout do mac80211 scan completion anyway. This assure we end scan
in case of firmware hung.
Patch fix one of the causes of wdev_cleanup_work warning reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assure (partially) we call ieee80211_scan_completed() only once when
scan was requested from mac80211.
Code path that first clear STATUS_SCANNING bit is responsible to call
ieee80211_scan_completed(). Before the call, we check if mac80211
really request the scan.
Still persist some cases when we behave wrong, that will be addressed
in the next patches.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since on timeout version of iwl_scan_cancel procedure we can sleep,
do not have to schedule abort_scan work to begin and perform scanning,
can do this directly. Also now, as we do not queue abort_scan from
restart work anymore, we can queue abort_scan to priv->workqueue.
Don't drop mutex when waiting for scan complete. Use STATUS_HW_SCAN bit
to check if scanning is currently pending, because STATUS_SCANNING will
be cleared only with priv->mutex taken.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we are not able to send abort command to firmware, notify mac80211
that we complete scan, as we will newer do it lately. Check for all
possible errors that low level sending command procedure does not check,
to assure we catch all failures cases.
Patch fix one of the causes of wdev_cleanup_work warning reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Always cancel scan when stooping device and scan is currently pending,
we should newer have scan running after down device.
To assure we start scan cancel from restart work we have to schedule
abort_scan to different workqueue than priv->workqueue.
Patch fix not cancel scanning when restarting firmware, what is
one of the causes of wdev_cleanup_work warning (together with permanent
network connection lost) reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 13 Sep 2010 12:46:34 +0000 (14:46 +0200)]
iwlwifi: move scan completed flags handling
Move the scan completed flags handling so that we
can notify mac80211 about aborted scans with the
correct status. Also queue the scan_completed work
before the BT status update so that it won't see
the bits still set (unless a new scan was started
in which case that's fine.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 13 Sep 2010 12:46:33 +0000 (14:46 +0200)]
iwlwifi: unify scan start checks
Rather than duplicating all the checks and even
in case of errors accepting the scan request
from mac80211, we can push the checks to the
caller and in all error cases reject the scan
request right away (rather than accepting and
then saying it was aborted).
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 13 Sep 2010 12:46:32 +0000 (14:46 +0200)]
iwlwifi: remove unused conf variables
There are a number of conf variables that are
unused, remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi W Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/ath9k: use ARRAY_SIZE macro in ani.c
Replace (sizeof(ofdm_level_table)/sizeof(ofdm_level_table[0]) with
ARRAY_SIZE(ofdm_level_table), and (sizeof(cck_level_table)/
sizeof(cck_level_table[0]) with ARRAY_SIZE(cck_level_table) in
drivers/net/wireless/ath/ath9k/ani.c
Signed-off-by: Nikitas Angelinas <nikitasangelinas@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 8 Sep 2010 18:57:40 +0000 (20:57 +0200)]
rt2x00: fix oops in rt2x00lib_txdone with rt61pci
Fix a typo introduced in "rt2x00: Add helper function for reporting tx
status" that results in an oops in rt2x00lib_txdone.
Reported-by: Pavel Roskin <proski@gnu.org> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 8 Sep 2010 18:57:10 +0000 (20:57 +0200)]
rt2x00: Enable missing interrupts in rt61pci
We're handling both, the CSR_BEACON_DONE and the CSR_TWAKEUP interrupts
in rt61pci. However, these interrupts are masked out by default. Fix
this.
Found via pure code inspection.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 8 Sep 2010 18:56:52 +0000 (20:56 +0200)]
rt2x00: Mask out unused interrupts in rt2800pci
We don't use all available interrupts in rt2800pci. Mask out all unused
interrupts to avoid waking up without having anything to do.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Wed, 8 Sep 2010 18:56:32 +0000 (20:56 +0200)]
rt2x00: Check for specific changed flags when updating the erp config
Previously rt2x00 was always updating all erp related config variables
even though mac80211 might only have changed one. Hence, pass the
changed flags to the config_erp driver callback so that the driver
can limit the changes to the correct values.
This fixes an issue in AP mode where the beacon interval is not
initialized (and thus zero) but still sent to the hardware causing an
interrupt storm on rt2800pci hanging the system.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log