Sonic Zhang [Wed, 30 Jan 2008 08:43:26 +0000 (16:43 +0800)]
Blackfin pata-bf54x driver: Add debug information
Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Wed, 30 Jan 2008 01:53:19 +0000 (19:53 -0600)]
sata_nv: fix for completion handling
This patch is based on an original patch from Kuan Luo of NVIDIA,
posted under subject "fixed a bug of adma in rhel4u5 with HDS7250SASUN500G".
His description follows. I've reworked it a bit to avoid some unnecessary
repeated checks but it should be functionally identical.
"The patch is to solve the error message "ata1: CPB flags CMD err,
flags=0x11" when testing HDS7250SASUN500G in rhel4u5.
I tested this hd in 2.6.24-rc7 which needed to remove the mask in
blacklist to run the ncq and the same error also showed up.
I traced the bug and found that the interrupt finished a command (for
example, tag=0) when the driver got that adma status is
NV_ADMA_STAT_DONE and cpb->resp_flags is NV_CPB_RESP_DONE.
However, For this hd, the drive maybe didn't clear bit 0 at this moment.
It meaned the hardware had not completely finished the command.
If at the same time the driver freed the command(tag 0) and sended
another command (tag 0), the error happened.
The notifier register is 32-bit register containing notifier value.
Value is bit vector containing one bit per tag number (0-31) in
corresponding bit positions (bit 0 is for tag 0, etc). When bit is set
then ADMA indicates that command with corresponding tag number completed
execution.
So i added the check notifier code. Sometimes i saw that the notifier
reg set some bits , but the adma status set NV_ADMA_STAT_CMD_COMPLETE
,not NV_ADMA_STAT_DONE. So i added the NV_ADMA_STAT_CMD_COMPLETE check
code."
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Saeed Bishara [Wed, 30 Jan 2008 22:50:45 +0000 (11:50 -1100)]
sata_mv: Remove PCI dependency
The integrated SATA controller is connected directly to the SoC's
internal bus, not via PCI interface. this patch removes the dependency
on the PCI interface.
Signed-off-by: Saeed Bishara <saeed@marvell.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Lord [Tue, 29 Jan 2008 18:24:00 +0000 (13:24 -0500)]
sata_mv ncq Introduce per-tag SG tables
In preparation for supporting NCQ, we must allocate separate SG tables
for each command tag, rather than just a single table per port as before.
Gen-I hardware cannot do NCQ, though, so we still allocate just a single
table for that, but populate it in all 32 slots to avoid special-cases
elsewhere in hotter paths of the code.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Lord [Sat, 26 Jan 2008 23:32:45 +0000 (18:32 -0500)]
sata_mv ncq Use DMA memory pools for hardware memory tables
Create host-owned DMA memory pools, for use in allocating/freeing per-port
command/response queues and SG tables. This gives us a way to guarantee we
meet the hardware address alignment requirements, and also reduces memory that
might otherwise be wasted on alignment gaps.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Lord [Sat, 26 Jan 2008 23:32:29 +0000 (18:32 -0500)]
sata_mv ncq Restrict max sectors to 8-bits on GenII NCQ
The GenII chips have only 8-bits for the sector_count field when performing NCQ.
Add a dev_config method to restrict this when necessary, taking care not to
override any other restriction already in place (likely none, but someday.. ?).
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Lord [Sat, 26 Jan 2008 23:31:33 +0000 (18:31 -0500)]
sata_mv ncq Add want ncq parameter for EDMA configuration
An extra EDMA config bit is required for NCQ operation.
So set/clear it as needed, and cache current setting in port_priv.
For now though, it will always be "off" (0).
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Lord [Sat, 26 Jan 2008 23:31:16 +0000 (18:31 -0500)]
sata_mv ncq Fix EDMA configuration
Simplify and fix EDMA configuration setup to match Marvell specificiations.
The chip documentation gives a specific (re)init sequence, which we now follow.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mark Lord [Sat, 26 Jan 2008 23:30:37 +0000 (18:30 -0500)]
sata_mv ncq Mask transient IRQs
The chips can handle many transient errors internally without a software IRQ.
We now mask/ignore those interrupts here. This is necessary for NCQ, later on.
Signed-off-by: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linus Torvalds [Fri, 1 Feb 2008 10:48:45 +0000 (21:48 +1100)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: kill swap_io_context()
as-iosched: fix inconsistent ioc->lock context
ide-cd: fix leftover data BUG
block: make elevator lib checkpatch compliant
cfq-iosched: make checkpatch compliant
block: make core bits checkpatch compliant
block: new end request handling interface should take unsigned byte counts
unexport add_disk_randomness
block/sunvdc.c:print_version() must be __devinit
splice: always updated atime in direct splice
Greg Ungerer [Fri, 1 Feb 2008 07:38:24 +0000 (17:38 +1000)]
m68knommu: fix 528x ColdFire cache settings
Fix problems with the 528x ColdFire CPU cache setup.
Do not cache the flash region (if present), and make the runtime
settings consistent with the init setting.
Problems pointed out by Bernd Buttner <b.buettner@mkc-gmbh.de>
Greg Ungerer [Fri, 1 Feb 2008 07:38:03 +0000 (17:38 +1000)]
m68knommu: create common DMA table for ColdFire CPUs
Move the ColdFire DMA address table into its own file, and out
of each of the different CPU config files. No need to have a copy
of it in each of the config setup files.
Greg Ungerer [Fri, 1 Feb 2008 07:37:56 +0000 (17:37 +1000)]
m68knommu: modify Makefiles to support common coldfire directory
Modify Makefiles to support separate coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Greg Ungerer [Fri, 1 Feb 2008 07:37:46 +0000 (17:37 +1000)]
m68knommu: move ColdFire vectors.c to its own coldfire directory
Move common ColdFire CPU vectors.c to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Greg Ungerer [Fri, 1 Feb 2008 07:37:39 +0000 (17:37 +1000)]
m68knommu: move ColdFire timers.c to its own coldfire directory
Move common ColdFire CPU timers.c to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Greg Ungerer [Fri, 1 Feb 2008 07:37:36 +0000 (17:37 +1000)]
m68knommu: move ColdFire pit.c to its own coldfire directory
Move common ColdFire CPU pit.c to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Greg Ungerer [Fri, 1 Feb 2008 07:37:28 +0000 (17:37 +1000)]
m68knommu: move ColdFire head.S to its own coldfire directory
Move common ColdFire CPU head.S to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Greg Ungerer [Fri, 1 Feb 2008 07:37:18 +0000 (17:37 +1000)]
m68knommu: move ColdFire entry.S to its own coldfire directory
Move common ColdFire CPU entry.S to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Greg Ungerer [Fri, 1 Feb 2008 07:35:03 +0000 (17:35 +1000)]
m68knommu: platform setup for 5407 ColdFire parts
Switch to platform style configuration for 5407 ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Greg Ungerer [Fri, 1 Feb 2008 07:34:58 +0000 (17:34 +1000)]
m68knommu: platform setup for 532x ColdFire parts
Switch to platform style configuration for 532x ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Greg Ungerer [Fri, 1 Feb 2008 07:34:40 +0000 (17:34 +1000)]
m68knommu: platform setup for 527x ColdFire parts
Switch to platform style configuration for 527x ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Greg Ungerer [Fri, 1 Feb 2008 07:34:55 +0000 (17:34 +1000)]
m68knommu: platform setup for 5307 ColdFire parts
Switch to platform style configuration for 5307 ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Greg Ungerer [Fri, 1 Feb 2008 07:34:50 +0000 (17:34 +1000)]
m68knommu: platform setup for 528x ColdFire parts
Switch to platform style configuration for 528x ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Greg Ungerer [Fri, 1 Feb 2008 07:34:30 +0000 (17:34 +1000)]
m68knommu: platform setup for 5249 ColdFire parts
Switch to platform style configuration for 5249 ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Greg Ungerer [Fri, 1 Feb 2008 07:34:32 +0000 (17:34 +1000)]
m68knommu: platform setup for 5272 ColdFire parts
Switch to platform style configuration for 5272 ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Greg Ungerer [Fri, 1 Feb 2008 07:34:10 +0000 (17:34 +1000)]
m68knommu: platform setup for 520x ColdFire parts
Switch to platform style configuration for 520x ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Greg Ungerer [Fri, 1 Feb 2008 07:34:15 +0000 (17:34 +1000)]
m68knommu: platform setup for 523x ColdFire parts
Switch to platform style configuration for 523x ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Greg Ungerer [Fri, 1 Feb 2008 07:34:04 +0000 (17:34 +1000)]
m68knommu: platform setup for 5206 ColdFire parts
Switch to platform style configuration for 5206 ColdFire parts.
Initial support is for the UARTs. DMA support moved to common code
for all ColdFire parts.
Al Viro [Fri, 1 Feb 2008 07:05:44 +0000 (07:05 +0000)]
Fix dl2k constants
The MSSR constants didn't match the reality - bitfield declarations used
to be correct (1000BT_FD - bit 11, 1000BT_HD - bit 10), but enum had
them the other way round. Went unnoticed until the switch from the
bitfields use to the explicit arithmetics and I hadn't caught that one
when verifying correctness of change...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jens Axboe [Fri, 1 Feb 2008 08:44:28 +0000 (09:44 +0100)]
as-iosched: fix inconsistent ioc->lock context
Since it's acquired from irq context, all locking must be of the
irq safe variant. Most are already inside the queue lock (which
already disables interrupts), but the io scheduler rmmod path
always has irqs enabled and the put_io_context() path may legally
be called with irqs enabled (even if it isn't usually). So fixup
those two.
Jens Axboe [Thu, 31 Jan 2008 12:57:51 +0000 (13:57 +0100)]
ide-cd: fix leftover data BUG
It's perfectly legal to have data leftovers when a drive signals
completion, it happens all the time when a user issues a command
with a transfer count that is too large.
Adrian Bunk [Wed, 30 Jan 2008 20:17:23 +0000 (21:17 +0100)]
block/sunvdc.c:print_version() must be __devinit
This patch fixes the following section mismatches:
<-- snip -->
...
WARNING: drivers/block/sunvdc.o(.text+0xf0): Section mismatch in reference from the function print_version() to the variable .devinit.data:version
WARNING: drivers/block/sunvdc.o(.text+0xf8): Section mismatch in reference from the function print_version() to the variable .devinit.data:version
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Jens Axboe [Wed, 30 Jan 2008 11:24:48 +0000 (12:24 +0100)]
splice: always updated atime in direct splice
Andre Majorel <aym-xunil@teaser.fr> points out that if we only updated
the atime when we transfer some data, we deviate from the standard
of always updating the atime. So change splice to always call
file_accessed() even if splice_direct_to_actor() didn't transfer
any data.
Sam Ravnborg [Fri, 1 Feb 2008 00:48:49 +0000 (16:48 -0800)]
[SPARC64]: Fix inconsistent .section usage in lib/
A few places missed the "a" specifier for the __ex_table section. Add
these so we avoid generation an additional section at link time.
Latest modpost would otherwise complain like this:
WARNING: vmlinux.o (__ex_table.2): section name inconsistency.
(.[number]+) following section name.
Did you forget to use "ax"/"aw" in a .S file?
Note that for example <linux/init.h> contains
section definitions for use in .S files.
WARNING: vmlinux.o (__ex_table.4): section name inconsistency.
(.[number]+) following section name.
Did you forget to use "ax"/"aw" in a .S file?
Note that for example <linux/init.h> contains
section definitions for use in .S files.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Denis V. Lunev [Fri, 1 Feb 2008 02:50:07 +0000 (18:50 -0800)]
[NETNS]: Lookup in FIB semantic hashes taking into account the namespace.
The namespace is not available in the fib_sync_down_addr, add it as a
parameter.
Looking up a device by the pointer to it is OK. Looking up using a
result from fib_trie/fib_hash table lookup is also safe. No need to
fix that at all. So, just fix lookup by address and insertion to the
hash table path.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Denis V. Lunev [Fri, 1 Feb 2008 02:49:32 +0000 (18:49 -0800)]
[NETNS]: Add a namespace mark to fib_info.
This is required to make fib_info lookups namespace aware. In the
other case initial namespace devices are marked as dead in the local
routing table during other namespace stop.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Denis V. Lunev [Fri, 1 Feb 2008 02:48:47 +0000 (18:48 -0800)]
[IPV4]: fib_sync_down rework.
fib_sync_down can be called with an address and with a device. In
reality it is called either with address OR with a device. The
codepath inside is completely different, so lets separate it into two
calls for these two cases.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Denis V. Lunev [Fri, 1 Feb 2008 02:47:00 +0000 (18:47 -0800)]
[IPV4]: Small style cleanup of the error path in rtm_to_ifaddr.
Remove error code assignment inside brackets on failure. The code
looks better if the error is assigned before condition check. Also,
the compiler treats this better.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Fri, 1 Feb 2008 02:37:42 +0000 (18:37 -0800)]
[NET_SCHED]: Add flow classifier
Add new "flow" classifier, which is meant to extend the SFQ hashing
capabilities without hard-coding new hash functions and also allows
deterministic mappings of keys to classes, replacing some out of tree
iptables patches like IPCLASSIFY (maps IPs to classes), IPMARK (maps
IPs to marks, with fw filters to classes), ...
Patrick McHardy [Fri, 1 Feb 2008 02:36:52 +0000 (18:36 -0800)]
[NET_SCHED]: sch_sfq: add support for external classifiers
Add support for external classifiers to allow using different flow
hash functions similar to ESFQ. When no classifier is attached the
built-in hash is used as before.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
o Outbound sequence number overflow error status
is counted as XfrmOutStateSeqError.
o Additionaly, it changes inbound sequence number replay
error name from XfrmInSeqOutOfWindow to XfrmInStateSeqError
to apply name scheme above.
o Inbound IPv4 UDP encapsuling type mismatch error is wrongly
mapped to XfrmInStateInvalid then this patch fiex the error
to XfrmInStateMismatch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Adrian Bunk [Fri, 1 Feb 2008 01:10:30 +0000 (17:10 -0800)]
[XFRM]: Remove unused exports.
This patch removes the following no longer used EXPORT_SYMBOL's:
- xfrm_input.c: xfrm_parse_spi
- xfrm_state.c: xfrm_replay_check
- xfrm_state.c: xfrm_replay_advance
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 1 Feb 2008 01:07:21 +0000 (17:07 -0800)]
[BNX2]: Fix ASYM PAUSE advertisement for remote PHY.
We were checking for the ASYM_PAUSE bit for 1000Base-X twice instead
checking for both the 1000Base-X bit and the 10/100/1000Base-T bit.
The purpose of the logic is to tell the firmware that ASYM_PAUSE is
set on either the Serdes or Copper interface.
Problem was discovered by Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 1 Feb 2008 01:05:09 +0000 (17:05 -0800)]
[IPV4] route cache: Introduce rt_genid for smooth cache invalidation
Current ip route cache implementation is not suited to large caches.
We can consume a lot of CPU when cache must be invalidated, since we
currently need to evict all cache entries, and this eviction is
sometimes asynchronous. min_delay & max_delay can somewhat control this
asynchronism behavior, but whole thing is a kludge, regularly triggering
infamous soft lockup messages. When entries are still in use, this also
consumes a lot of ram, filling dst_garbage.list.
A better scheme is to use a generation identifier on each entry,
so that cache invalidation can be performed by changing the table
identifier, without having to scan all entries.
No more delayed flushing, no more stalling when secret_interval expires.
Invalidated entries will then be freed at GC time (controled by
ip_rt_gc_timeout or stress), or when an invalidated entry is found
in a chain when an insert is done.
Thus we keep a normal equilibrium.
This patch :
- renames rt_hash_rnd to rt_genid (and makes it an atomic_t)
- Adds a new rt_genid field to 'struct rtable' (filling a hole on 64bit)
- Checks entry->rt_genid at appropriate places :
Patrick McHardy [Fri, 1 Feb 2008 00:57:15 +0000 (16:57 -0800)]
[NET_SCHED]: sch_ingress: remove netfilter support
Since the old policer code is gone, TC actions are needed for policing.
The ingress qdisc can get packets directly from netif_receive_skb()
in case TC actions are enabled or through netfilter otherwise, but
since without TC actions there is no policer the only thing it actually
does is count packets.
Remove the netfilter support and always require TC actions.
Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Rami Rosen [Fri, 1 Feb 2008 00:56:03 +0000 (16:56 -0800)]
[MACVLAN]: Setting macvlan_handle_frame_hook to NULL when rtnl_link_register() fails.
In drivers/net/macvlan.c, when rtnl_link_register() fails in
macvlan_init_module(), there is no point to set it (second time in
this method) to macvlan_handle_frame; macvlan_init_module() will
return a negative number, so instead this patch sets
macvlan_handle_frame_hook to NULL.
Signed-off-by: Rami Rosen <ramirose@gmail.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Leech [Fri, 1 Feb 2008 00:53:23 +0000 (16:53 -0800)]
[VLAN]: set_rx_mode support for unicast address list
Reuse the existing logic for multicast list synchronization for the
unicast address list. The core of dev_mc_sync/unsync are split out as
__dev_addr_sync/unsync and moved from dev_mcast.c to dev.c. These are
then used to implement dev_unicast_sync/unsync as well.
I'm working on cleaning up Intel's FCoE stack, which generates new MAC
addresses from the fibre channel device id assigned by the fabric as
per the current draft specification in T11. When using such a
protocol in a VLAN environment it would be nice to not always be
forced into promiscuous mode, assuming the underlying Ethernet driver
supports multiple unicast addresses as well.
Signed-off-by: Chris Leech <christopher.leech@intel.com> Signed-off-by: Patrick McHardy <kaber@trash.net>
Shan Wei [Fri, 1 Feb 2008 00:47:27 +0000 (16:47 -0800)]
[TCP]: Fix a bug in strategy_allowed_congestion_control
In strategy_allowed_congestion_control of the 2.6.24 kernel, when
sysctl_string return 1 on success,it should call
tcp_set_allowed_congestion_control to set the allowed congestion
control.But, it don't. the sysctl_string return 1 on success,
otherwise return negative, never return 0.The patch fix the problem.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[IPV4] fib_trie: rescan if key is lost during dump
Normally during a dump the key of the last dumped entry is used for
continuation, but since lock is dropped it might be lost. In that case
fallback to the old counter based N^2 behaviour. This means the dump
will end up skipping some routes which matches what FIB_HASH does.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log