Bjorn Helgaas [Mon, 12 Dec 2016 17:25:06 +0000 (11:25 -0600)]
Merge branch 'pci/host-altera' into next
* pci/host-altera:
PCI: altera: Remove redundant error message in altera_pcie_parse_dt()
PCI: altera: Use builtin_platform_driver() to simplify the code
Bjorn Helgaas [Mon, 12 Dec 2016 17:25:05 +0000 (11:25 -0600)]
Merge branch 'pci/virtualization' into next
* pci/virtualization:
PCI: Add comments about ROM BAR updating
PCI: Decouple IORESOURCE_ROM_ENABLE and PCI_ROM_ADDRESS_ENABLE
PCI: Remove pci_resource_bar() and pci_iov_resource_bar()
PCI: Don't update VF BARs while VF memory space is enabled
PCI: Separate VF BAR updates from standard BAR updates
PCI: Update BARs using property bits appropriate for type
PCI: Ignore BAR updates on virtual functions
PCI: Do any VF BAR updates before enabling the BARs
PCI: Support INTx masking on ConnectX-4 with firmware x.14.1100+
PCI: Convert Mellanox broken INTx quirks to be for listed devices only
PCI: Convert broken INTx masking quirks from HEADER to FINAL
net/mlx4_core: Use device ID defines
PCI: Add Mellanox device IDs
Bjorn Helgaas [Mon, 12 Dec 2016 17:25:04 +0000 (11:25 -0600)]
Merge branch 'pci/pm' into next
* pci/pm:
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI: pciehp: Add runtime PM support for PCIe hotplug ports
ACPI / hotplug / PCI: Make device_is_managed_by_native_pciehp() public
ACPI / hotplug / PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Unfold conditions to block runtime PM on PCIe ports
PCI: Consolidate conditions to allow runtime PM on PCIe ports
PCI: Activate runtime PM on a PCIe port only if it can suspend
PCI: Speed up algorithm in pci_bridge_d3_update()
PCI: Autosense device removal in pci_bridge_d3_update()
PCI: Don't acquire ref on parent in pci_bridge_d3_update()
USB: UHCI: report non-PME wakeup signalling for Intel hardware
PCI: Check for PME in targeted sleep state
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
There is at least one Chelsio 10Gb card which uses VPD area to store some
non-standard blocks (example below). However pci_vpd_size() returns the
length of the first block only assuming that there can be only one VPD "End
Tag".
Since 4e1a635552d3 ("vfio/pci: Use kernel VPD access functions"), VFIO
blocks access beyond that offset, which prevents the guest "cxgb3" driver
from probing the device. The host system does not have this problem as its
driver accesses the config space directly without pci_read_vpd().
Add a quirk to override the VPD size to a bigger value. The maximum size
is taken from EEPROMSIZE in drivers/net/ethernet/chelsio/cxgb3/common.h.
We do not read the tag as the cxgb3 driver does as the driver supports
writing to EEPROM/VPD and when it writes, it only checks for 8192 bytes
boundary. The quirk is registered for all devices supported by the cxgb3
driver.
This adds a quirk to the PCI layer (not to the cxgb3 driver) as the cxgb3
driver itself accesses VPD directly and the problem only exists with the
vfio-pci driver (when cxgb3 is not running on the host and may not be even
loaded) which blocks accesses beyond the first block of VPD data. However
vfio-pci itself does not have quirks mechanism so we add it to PCI.
This is the controller:
Ethernet controller [0200]: Chelsio Communications Inc T310 10GbE Single Port Adapter [1425:0030]
This is what I parsed from its VPD:
===
b'\x82*\x0010 Gigabit Ethernet-SR PCI Express Adapter\x90J\x00EC\x07D76809 FN\x0746K'
0000 Large item 42 bytes; name 0x2 Identifier String
b'10 Gigabit Ethernet-SR PCI Express Adapter'
002d Large item 74 bytes; name 0x10
#00 [EC] len=7: b'D76809 '
#0a [FN] len=7: b'46K7897'
#14 [PN] len=7: b'46K7897'
#1e [MN] len=4: b'1037'
#25 [FC] len=4: b'5769'
#2c [SN] len=12: b'YL102035603V'
#3b [NA] len=12: b'00145E992ED1'
007a Small item 1 bytes; name 0xf End Tag
Bjorn Helgaas [Tue, 15 Nov 2016 13:57:30 +0000 (07:57 -0600)]
PCI: pciehp: Remove loading message
Remove the "PCI Express Hot Plug Controller Driver" version message. I
don't think it contains any useful information. Remove unused #defines
and move the author information to a comment.
Bjorn Helgaas [Tue, 15 Nov 2016 13:55:51 +0000 (07:55 -0600)]
PCI: hotplug: Remove hotplug core message
Remove the "PCI Hot Plug PCI Core" version message. I don't think it
contains any useful information. Remove unused #defines and move the
author information to a comment.
Bjorn Helgaas [Tue, 15 Nov 2016 13:54:19 +0000 (07:54 -0600)]
PCI: Remove service driver load/unload messages
Remove the "service driver %s loaded" and unloaded messages. All service
drivers already log something in their probe functions, where they can log
more useful details.
Bjorn Helgaas [Mon, 21 Nov 2016 21:07:53 +0000 (15:07 -0600)]
PCI/PME: Log PME IRQ when claiming Root Port
We already log a "Signaling PME" whenever the PME service driver claims a
Root Port. In fact, we also log the same message for every device in the
hierarchy below the Root Port.
Log the "Signaling PME" once (only for the Root Port, since we can
trivially find out which devices are below the Root Port), and include the
IRQ number in the message to help connect the dots with /proc/interrupts.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Wang Sheng-Hui [Thu, 22 Sep 2016 01:05:46 +0000 (09:05 +0800)]
PCI: Move config space size macros to pci_regs.h
Move PCI configuration space size macros (PCI_CFG_SPACE_SIZE and
PCI_CFG_SPACE_EXP_SIZE) from drivers/pci/pci.h to
include/uapi/linux/pci_regs.h so they can be used by more drivers and
eliminate duplicate definitions.
[bhelgaas: Expand comment to include PCI-X details] Signed-off-by: Wang Sheng-Hui <shhuiw@foxmail.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
David Daney [Thu, 17 Nov 2016 22:25:01 +0000 (14:25 -0800)]
PCI/ASPM: Don't retrain link if ASPM not possible
Some (defective) PCIe devices are not able to reliably do link retraining.
Check to see if ASPM is possible between link partners before configuring
common clocking, and doing the resulting link retraining. If ASPM is not
possible, there is no reason to risk losing access to a device due to an
unnecessary link retraining.
Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Ashok Raj [Sat, 19 Nov 2016 08:32:46 +0000 (00:32 -0800)]
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
If an error occurs when enabling a slot, pciehp_power_thread() turns off
the power indicator. But if the only error is that the slot was already
enabled, we should leave the power indicator on.
Return success if called to enable an already-enabled slot.
This is in the same spirit of the special handling for EEXISTS when
pciehp_configure_device() determines the slot devices already exist.
Ashok Raj [Sat, 19 Nov 2016 08:32:45 +0000 (00:32 -0800)]
PCI: pciehp: Prioritize data-link event over presence detect
If Slot Status indicates changes in both Data Link Layer Status and
Presence Detect, prioritize the Link status change.
When both events are observed, pciehp currently relies on the Slot Status
Presence Detect State (PDS) to agree with the Link Status Data Link Layer
Active status. The Presence Detect State, however, may be set to 1 through
out-of-band presence detect even if the link is down, which creates
conflicting events.
Since the Link Status accurately reflects the reachability of the
downstream bus, the Link Status event should take precedence over a
Presence Detect event. Skip checking the PDC status if we handled a link
event in the same handler.
Bjorn Helgaas [Tue, 6 Dec 2016 20:27:59 +0000 (14:27 -0600)]
PCI: Explain ARM64 ACPI/MCFG quirk Kconfig and build strategy
Add Makefile comments to explain the Kconfig and build strategy for ARM64
drivers that work around not-quite-ECAM issues. No functional change
intended.
Duc Dang [Fri, 2 Dec 2016 02:27:07 +0000 (18:27 -0800)]
PCI: Add MCFG quirks for X-Gene host controller
PCIe controllers in X-Gene SoCs are not ECAM compliant: software needs to
configure additional controller's register to address device at
bus:dev:function.
Add a quirk to discover controller MMIO register space and configure
controller registers to select and address the target secondary device.
The quirk will only be applied for X-Gene PCIe MCFG table with
OEM revison 1, 2, 3 or 4 (PCIe controller v1 and v2 on X-Gene SoCs).
Tomasz Nowicki [Thu, 1 Dec 2016 05:16:34 +0000 (23:16 -0600)]
PCI: Add MCFG quirks for Cavium ThunderX pass1.x host controller
ThunderX pass1.x requires to emulate the EA headers for on-chip devices
hence it has to use custom pci_thunder_ecam_ops for accessing PCI config
space (pci-thunder-ecam.c). Add new entries to MCFG quirk array where it
can be applied while probing ACPI based PCI host controller.
ThunderX pass1.x is using the same way for accessing off-chip devices
(so-called PEM) as silicon pass-2.x so we need to add PEM quirk entries
too.
Quirk is considered for ThunderX silicon pass1.x only which is identified
via MCFG revision 2.
ThunderX pass 1.x requires the following accessors:
NUMA node 0 PCI segments 0- 3: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 10-13: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: change Makefile/ifdefs so quirk doesn't depend on
CONFIG_PCI_HOST_THUNDER_ECAM] Signed-off-by: Tomasz Nowicki <tn@semihalf.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tomasz Nowicki [Thu, 1 Dec 2016 06:07:56 +0000 (00:07 -0600)]
PCI: Add MCFG quirks for Cavium ThunderX pass2.x host controller
ThunderX PCIe controller to off-chip devices (so-called PEM) is not fully
compliant with ECAM standard. It uses non-standard configuration space
accessors (see thunder_pem_ecam_ops) and custom configuration space
granulation (see bus_shift = 24). In order to access configuration space
and probe PEM as ACPI-based PCI host controller we need to add MCFG quirk
infrastructure. This involves:
1. A new thunder_pem_acpi_init() init function to locate PEM-specific
register ranges using ACPI.
2. Export PEM thunder_pem_ecam_ops structure so it is visible to MCFG quirk
code.
3. New quirk entries for each PEM segment. Each contains platform IDs,
mentioned thunder_pem_ecam_ops and CFG resources.
Quirk is considered for ThunderX silicon pass2.x only which is identified
via MCFG revision 1.
ThunderX pass 2.x requires the following accessors:
NUMA Node 0 PCI segments 0- 3: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA Node 1 PCI segments 10-13: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: adapt to use acpi_get_rc_resources(), update Makefile/ifdefs so
quirk doesn't depend on CONFIG_PCI_HOST_THUNDER_PEM] Signed-off-by: Tomasz Nowicki <tn@semihalf.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Dongdong Liu [Thu, 1 Dec 2016 06:45:35 +0000 (00:45 -0600)]
PCI: Add MCFG quirks for HiSilicon Hip05/06/07 host controllers
The PCIe controller in Hip05/Hip06/Hip07 SoCs is not completely
ECAM-compliant. It is non-ECAM only for the RC bus config space; for any
other bus underneath the root bus it does support ECAM access.
Add specific quirks for PCI config space accessors. This involves:
1. New initialization call hisi_pcie_init() to obtain RC base
addresses from PNP0C02 at the root of the ACPI namespace (under \_SB).
2. New entry in common quirk array.
[bhelgaas: move to pcie-hisi.c and change Makefile/ifdefs so quirk doesn't
depend on CONFIG_PCI_HISI] Signed-off-by: Dongdong Liu <liudongdong3@huawei.com> Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Dongdong Liu [Thu, 1 Dec 2016 06:33:42 +0000 (00:33 -0600)]
PCI/ACPI: Provide acpi_get_rc_resources() for ARM64 platform
The acpi_get_rc_resources() is used to get the RC register address that can
not be described in MCFG. It takes the _HID & segment to look for and
outputs the RC address resource. Use PNP0C02 devices to describe such RC
address resource. Use _UID to match segment to tell which root bus the
PNP0C02 resource belongs to.
[bhelgaas: add dev argument, wrap in #ifdef CONFIG_PCI_QUIRKS] Signed-off-by: Dongdong Liu <liudongdong3@huawei.com> Signed-off-by: Tomasz Nowicki <tn@semihalf.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tomasz Nowicki [Fri, 9 Sep 2016 19:24:04 +0000 (21:24 +0200)]
PCI/ACPI: Check for platform-specific MCFG quirks
The PCIe spec (r3.0, sec 7.2.2) specifies an "Enhanced Configuration Access
Mechanism" (ECAM) for memory-mapped access to configuration space. ECAM is
required for PCIe systems unless there's a standard firmware interface for
config access.
In the absence of a firmware interface, we use pci_generic_ecam_ops, and on
ACPI systems, we discover the ECAM space via the MCFG table and/or the _CBA
method.
Unfortunately some systems provide MCFG but don't implement ECAM according
to spec, so we need a mechanism for quirks to make those systems work.
Add an MCFG quirk mechanism to override the config accessor functions
and/or the memory-mapped address space.
A quirk is selected if it matches all of the following:
- OEM ID
- OEM Table ID
- OEM Revision
- PCI segment (from _SEG)
- PCI bus number range (from _CRS, wildcard allowed)
If the quirk specifies config accessor functions or a memory-mapped address
range, these override the defaults.
[bhelgaas: changelog, reorder quirk matching, fix oem_revision typo per
Duc, add under #ifdef CONFIG_PCI_QUIRKS] Signed-off-by: Tomasz Nowicki <tn@semihalf.com> Signed-off-by: Dongdong Liu <liudongdong3@huawei.com> Signed-off-by: Christopher Covington <cov@codeaurora.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tomasz Nowicki [Fri, 9 Sep 2016 19:24:03 +0000 (21:24 +0200)]
PCI/ACPI: Extend pci_mcfg_lookup() to return ECAM config accessors
pci_mcfg_lookup() is the external interface to the generic MCFG code.
Previously it merely looked up the ECAM base address for a given domain and
bus range. We want a way to add MCFG quirks, some of which may require
special config accessors and adjustments to the ECAM address range.
Extend pci_mcfg_lookup() so it can return a pointer to a pci_ecam_ops
structure and a struct resource for the ECAM address space. For now, it
always returns &pci_generic_ecam_ops (the standard accessor) and the
resource described by the MCFG.
No functional changes intended.
[bhelgaas: changelog] Signed-off-by: Tomasz Nowicki <tn@semihalf.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Bjorn Helgaas [Fri, 2 Dec 2016 23:25:54 +0000 (17:25 -0600)]
arm64: PCI: Exclude ACPI "consumer" resources from host bridge windows
On x86 and ia64, we have treated all ACPI _CRS resources of PNP0A03 host
bridge devices as "producers", i.e., as host bridge windows. That's partly
because some x86 BIOSes improperly used "consumer" descriptors to describe
windows and partly because Linux didn't have good support for handling
consumer and producer descriptors differently.
One result is that x86 BIOSes describe host bridge "consumer" resources in
the _CRS of a PNP0C02 device, not the PNP0A03 device itself. On arm64 we
don't have a legacy of firmware that has this consumer/producer confusion,
so we can handle PNP0A03 "consumer" descriptors as host bridge registers
instead of windows.
Exclude non-window ("consumer") resources from the list of host bridge
windows. This allows the use of "consumer" PNP0A03 descriptors for bridge
register space.
Tomasz Nowicki [Thu, 24 Nov 2016 11:05:23 +0000 (12:05 +0100)]
arm64: PCI: Manage controller-specific data on per-controller basis
Currently we use one shared global acpi_pci_root_ops structure to keep
controller-specific ops. We pass its pointer to acpi_pci_root_create() and
associate it with a host bridge instance for good. Such a design implies
serious drawback. Any potential manipulation on the single system-wide
acpi_pci_root_ops leads to kernel crash. The structure content is not
really changing even across multiple host bridges creation; thus it was not
an issue so far.
In preparation for adding ECAM quirks mechanism (where controller-specific
PCI ops may be different for each host bridge) allocate new
acpi_pci_root_ops and fill in with data for each bridge. Now it is safe to
have different controller-specific info. As a consequence free
acpi_pci_root_ops when host bridge is released.
No functional changes in this patch.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Bjorn Helgaas [Wed, 30 Nov 2016 20:48:33 +0000 (14:48 -0600)]
arm64: PCI: Search ACPI namespace to ensure ECAM space is reserved
The static MCFG table tells us the base of ECAM space, but it does not
reserve the space -- the reservation should be done via a device in the
ACPI namespace whose _CRS includes the ECAM region.
Use acpi_resource_consumer() to check whether the ECAM space is reserved by
an ACPI namespace device. If it is, emit a message showing which device
reserves it. If not, emit a "[Firmware Bug]" warning.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Bjorn Helgaas [Wed, 30 Nov 2016 20:47:13 +0000 (14:47 -0600)]
ACPI: Add acpi_resource_consumer() to find device that claims a resource
Add acpi_resource_consumer(). This takes a struct resource and searches
the ACPI namespace for a device whose current resource settings (_CRS)
includes the resource. It returns the device if it exists, or NULL if no
device uses the resource.
If more than one device uses the resource (this may happen in the case of
bridges), acpi_resource_consumer() returns the first one found by
acpi_get_devices() in its modified depth-first walk of the namespace.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bjorn Helgaas [Mon, 28 Nov 2016 22:17:41 +0000 (16:17 -0600)]
PCI: Add comments about ROM BAR updating
pci_update_resource() updates a hardware BAR so its address matches the
kernel's struct resource UNLESS it's a disabled ROM BAR. We only update
those when we enable the ROM.
It's not obvious from the code why ROM BARs should be handled specially.
Apparently there are Matrox devices with defective ROM BARs that read as
zero when disabled. That means that if pci_enable_rom() reads the disabled
BAR, sets PCI_ROM_ADDRESS_ENABLE (without re-inserting the address), and
writes it back, it would enable the ROM at address zero.
Add comments and references to explain why we can't make the code look more
rational.
The code changes are from 755528c860b0 ("Ignore disabled ROM resources at
setup") and 8085ce084c0f ("[PATCH] Fix PCI ROM mapping").
Bjorn Helgaas [Mon, 28 Nov 2016 23:21:02 +0000 (17:21 -0600)]
PCI: Decouple IORESOURCE_ROM_ENABLE and PCI_ROM_ADDRESS_ENABLE
Remove the assumption that IORESOURCE_ROM_ENABLE == PCI_ROM_ADDRESS_ENABLE.
PCI_ROM_ADDRESS_ENABLE is the ROM enable bit defined by the PCI spec, so if
we're reading or writing a BAR register value, that's what we should use.
IORESOURCE_ROM_ENABLE is a corresponding bit in struct resource flags.
Bjorn Helgaas [Mon, 28 Nov 2016 22:43:06 +0000 (16:43 -0600)]
PCI: Don't update VF BARs while VF memory space is enabled
If we update a VF BAR while it's enabled, there are two potential problems:
1) Any driver that's using the VF has a cached BAR value that is stale
after the update, and
2) We can't update 64-bit BARs atomically, so the intermediate state
(new lower dword with old upper dword) may conflict with another
device, and an access by a driver unrelated to the VF may cause a bus
error.
Warn about attempts to update VF BARs while they are enabled. This is a
programming error, so use dev_WARN() to get a backtrace.
Bjorn Helgaas [Mon, 28 Nov 2016 15:15:52 +0000 (09:15 -0600)]
PCI: Separate VF BAR updates from standard BAR updates
Previously pci_update_resource() used the same code path for updating
standard BARs and VF BARs in SR-IOV capabilities.
Split the VF BAR update into a new pci_iov_update_resource() internal
interface, which makes it simpler to compute the BAR address (we can get
rid of pci_resource_bar() and pci_iov_resource_bar()).
This patch:
- Renames pci_update_resource() to pci_std_update_resource(),
- Adds pci_iov_update_resource(),
- Makes pci_update_resource() a wrapper that calls the appropriate one,
Bjorn Helgaas [Tue, 29 Nov 2016 14:14:47 +0000 (08:14 -0600)]
PCI: Update BARs using property bits appropriate for type
The BAR property bits (0-3 for memory BARs, 0-1 for I/O BARs) are supposed
to be read-only, but we do save them in res->flags and include them when
updating the BAR.
Mask the I/O property bits with ~PCI_BASE_ADDRESS_IO_MASK (0x3) instead of
PCI_REGION_FLAG_MASK (0xf) to make it obvious that we can't corrupt bits
2-3 of I/O addresses.
Use PCI_ROM_ADDRESS_MASK for ROM BARs. This means we'll only check the top
21 bits (instead of the 28 bits we used to check) of a ROM BAR to see if
the update was successful.
Bjorn Helgaas [Mon, 28 Nov 2016 17:19:27 +0000 (11:19 -0600)]
PCI: Ignore BAR updates on virtual functions
VF BARs are read-only zero, so updating VF BARs will not have any effect.
See the SR-IOV spec r1.1, sec 3.4.1.11.
We already ignore these updates because of 70675e0b6a1a ("PCI: Don't try to
restore VF BARs"); this merely restructures it slightly to make it easier
to split updates for standard and SR-IOV BARs.
Gavin Shan [Wed, 26 Oct 2016 01:15:35 +0000 (12:15 +1100)]
PCI: Do any VF BAR updates before enabling the BARs
Previously we enabled VFs and enable their memory space before calling
pcibios_sriov_enable(). But pcibios_sriov_enable() may update the VF BARs:
for example, on PPC PowerNV we may change them to manage the association of
VFs to PEs.
Because 64-bit BARs cannot be updated atomically, it's unsafe to update
them while they're enabled. The half-updated state may conflict with other
devices in the system.
Call pcibios_sriov_enable() before enabling the VFs so any BAR updates
happen while the VF BARs are disabled.
Noa Osherovich [Tue, 15 Nov 2016 08:00:00 +0000 (10:00 +0200)]
PCI: Support INTx masking on ConnectX-4 with firmware x.14.1100+
Mellanox devices were marked as having INTx masking ability broken. As a
result, the VFIO driver fails to start when more than one device function
is passed-through to a VM if both have the same INTx pin.
Prior to Connect-IB, Mellanox devices exposed to the operating system one
PCI function per all ports. Starting from Connect-IB, the devices are
function-per-port. When passing the second function to a VM, VFIO will
fail to start.
Exclude ConnectX-4, ConnectX4-Lx and Connect-IB from the list of Mellanox
devices marked as having broken INTx masking:
- ConnectX-4 and ConnectX4-LX firmware version is checked. If INTx
masking is supported, we unmark the broken INTx masking.
- Connect-IB does not support INTx currently so will not cause any
problem.
[bhelgaas: call pci_disable_device() always, after iounmap()] Fixes: 11e42532ada3 ("PCI: Assume all Mellanox devices have broken INTx masking") Signed-off-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Bjorn Helgaas [Mon, 31 Oct 2016 21:00:01 +0000 (16:00 -0500)]
PCI: Warn on possible RW1C corruption for sub-32 bit config writes
Hardware that supports only 32-bit config writes is not spec-compliant.
For example, if software performs a 16-bit write, we must do a 32-bit read,
merge in the 16 bits we intend to write, followed by a 32-bit write. If
the 16 bits we *don't* intend to write happen to have any RW1C (write-one-
to-clear) bits set, we just inadvertently cleared something we shouldn't
have.
Add a rate-limited warning when we do sub-32 bit config writes. Remove
similar probe-time warnings from some of the affected host bridge drivers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Enthusiastically-Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Shawn Lin <shawn.lin@rock-chips.com> # rockchip Acked-by: Thierry Reding <treding@nvidia.com>
Emil Velikov [Mon, 21 Nov 2016 22:24:49 +0000 (16:24 -0600)]
PCI: Create revision file in sysfs
Currently the revision isn't available via sysfs/libudev thus if one wants
to know the value one needs to read through the config file, which can be
quite time-consuming because it wakes/powers up the device.
There are at least two userspace components which could make use the new
file: libpciaccess and libdrm. The former wakes up _every_ PCI device,
which can be observed via glxinfo when using Mesa 10.0+ drivers. The
latter, in association with Mesa 13.0, can lead to 2-3 second delays while
starting firefox, thunderbird or chromium.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=98502 Tested-by: Mauro Santos <registo.mailling@gmail.com> Signed-off-by: Emil Velikov <emil.velikov@collabora.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch CC: Greg KH <gregkh@linuxfoundation.org>
Lukas Wunner [Fri, 28 Oct 2016 08:52:06 +0000 (10:52 +0200)]
PCI: pciehp: Add runtime PM support for PCIe hotplug ports
Linux 4.8 added support for runtime suspending PCIe ports to D3hot with
commit 006d44e49a25 ("PCI: Add runtime PM support for PCIe ports"), but
excluded hotplug ports. Those are now afforded runtime PM by the present
commit.
Hotplug ports require a few extra considerations:
- The configuration space of the port remains accessible in D3hot, so all
the functions to read or modify the Slot Status and Slot Control
registers need not be modified. Even turning on slot power doesn't seem
to require the port to be in D0, at least the PCIe spec doesn't say so
and I confirmed that by testing with a Thunderbolt controller.
- However D0 is required to access devices on the secondary bus. This
happens in pciehp_check_link_status() and pciehp_configure_device() (both
called from board_added()) and in pciehp_unconfigure_device() (called
from remove_board()), so acquire a runtime PM ref for their invocation.
- The hotplug port stays active as long as it has active children. If all
hotplugged devices below the port runtime suspend, the port is allowed to
runtime suspend as well. Plug and unplug detection continues to work in
D3hot.
- Hotplug interrupts are delivered in-band, so while the hotplug port
itself is allowed to go to D3hot, its parent ports must stay in D0 for
interrupts to come through. Add a corresponding restriction to
pci_dev_check_d3cold().
- Runtime PM may only be allowed if the hotplug port is handled natively by
the OS. On ACPI systems, the port may alternatively be handled by the
firmware and things break if the OS puts the port into D3 behind the
firmware's back: E.g. Thunderbolt hotplug ports on non-Macs are handled
by Intel's firmware in System Management Mode and the firmware is known
to access devices on the port's secondary bus without checking first if
the port is in D0: https://bugzilla.kernel.org/show_bug.cgi?id=53811
Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> CC: Mika Westerberg <mika.westerberg@linux.intel.com>
Lukas Wunner [Fri, 28 Oct 2016 08:52:06 +0000 (10:52 +0200)]
ACPI / hotplug / PCI: Make device_is_managed_by_native_pciehp() public
We're about to add runtime PM of hotplug ports, but we need to restrict it
to ports that are handled natively by the OS: If they're handled by the
firmware (which is the case for Thunderbolt on non-Macs), things would
break if the OS put the ports into D3hot behind the firmware's back.
To determine if a hotplug port is handled natively, one has to walk up from
the port to the root bridge and check the cached _OSC Control Field for the
value of the "PCI Express Native Hot Plug control" bit. There's already a
function to do that, device_is_managed_by_native_pciehp(), but it's private
to drivers/pci/hotplug/acpiphp_glue.c and only compiled in if
CONFIG_HOTPLUG_PCI_ACPI is enabled.
Make it public and move it to drivers/pci/pci-acpi.c, so that it is
available in the more general CONFIG_ACPI case.
The function contains a check if the device in question is a hotplug port
and returns false if it's not. The caller we're going to add doesn't need
this as it only calls the function if it actually *is* a hotplug port.
Move the check out of the function into the single existing caller.
Rename it to pciehp_is_native() and add some kerneldoc and polish.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukas Wunner [Fri, 28 Oct 2016 08:52:06 +0000 (10:52 +0200)]
ACPI / hotplug / PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
We cache the PCI_EXP_SLTCAP_HPC bit in pci_dev->is_hotplug_bridge on device
probe, so there's no need to read it again when adding the ACPI hotplug
context.
Here's the call chain to prove that no ordering issue is introduced:
pci_scan_child_bus [drivers/pci/probe.c]
pci_scan_slot
pci_scan_single_device
pci_scan_device
pci_setup_device
set_pcie_hotplug_bridge
[is_hotplug_bridge bit is set here]
pci_scan_bridge
pci_add_new_bus
pci_alloc_child_bus
pcibios_add_bus [arch/(x86|arm64|ia64)/...]
acpi_pci_add_bus [drivers/pci/pci-acpi.c]
acpiphp_enumerate_slots [drivers/pci/hotplug/acpiphp_glue.c]
acpiphp_add_context
device_is_managed_by_native_pciehp
[is_hotplug_bridge bit is queried here]
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukas Wunner [Fri, 28 Oct 2016 08:52:06 +0000 (10:52 +0200)]
PCI: Unfold conditions to block runtime PM on PCIe ports
The conditions to block D3 on parent ports are currently condensed into a
single expression in pci_dev_check_d3cold(). Upcoming commits will add
further conditions for hotplug ports, making this expression fairly large
and impenetrable. Unfold the conditions to maintain readability when they
are amended.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Mika Westerberg <mika.westerberg@linux.intel.com> CC: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukas Wunner [Fri, 28 Oct 2016 08:52:06 +0000 (10:52 +0200)]
PCI: Consolidate conditions to allow runtime PM on PCIe ports
The conditions to allow runtime PM on PCIe ports are currently spread
across two different files: The condition relating to hotplug ports is
located in portdrv_pci.c whereas all other conditions are located in pci.c.
Consolidate all conditions in a single place in pci.c, thus making it
easier to follow the logic and amend conditions down the road.
Note that the condition relating to hotplug ports is inserted *before* the
condition relating to the "pcie_port_pm=force" command line option, so
runtime PM is not afforded to hotplug ports even if this option is given.
That's exactly how the code behaved up until now. If this is not desired,
the ordering of the conditions can simply be reversed.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukas Wunner [Fri, 28 Oct 2016 08:52:06 +0000 (10:52 +0200)]
PCI: Activate runtime PM on a PCIe port only if it can suspend
Currently pcie_portdrv_probe() activates runtime PM on a PCIe port even
if it will never actually suspend because the BIOS is too old or the
"pcie_port_pm=off" option was specified on the kernel command line.
A few CPU cycles can be saved by not activating runtime PM at all in these
cases, because rpm_idle() and rpm_suspend() will bail out right at the
beginning when calling rpm_check_suspend_allowed(), instead of carrying out
various locking and assignments, invoking rpm_callback(), getting back
-EBUSY and rolling everything back.
The conditions checked in pci_bridge_d3_possible() are all static, they
never change during uptime of the system, hence it's safe to call this to
determine if runtime PM should be activated.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukas Wunner [Fri, 28 Oct 2016 08:52:06 +0000 (10:52 +0200)]
PCI: Speed up algorithm in pci_bridge_d3_update()
After a device has been added, removed or had its D3cold attributes
changed, we recheck whether its parent bridge may runtime suspend to D3hot
with pci_bridge_d3_update().
The most naive algorithm would be to iterate over the bridge's children and
check if any of them are blocking D3.
The function already tries to be a bit smarter than that by first checking
the device that was changed. If this device already blocks D3 on the
bridge, then walking over all the other children can be skipped. A
drawback of this approach is that if the device is *not* blocking D3, it
will be checked a second time by pci_walk_bus(). But that's cheap and is
outweighed by the performance gain of potentially skipping pci_walk_bus()
altogether.
The algorithm can be optimized further by taking into account if D3 is
currently allowed for the bridge, as shown in the following truth table:
(a) remove && bridge_d3: D3 is currently allowed for the bridge and
removing one of its children won't change
that. No action necessary.
(b) remove && !bridge_d3: D3 may now be allowed for the bridge if the
removed child was the only one blocking it.
Check all its siblings to verify that.
(c) !remove && bridge_d3: D3 may now be disallowed but this can only
be caused by the added/changed child, not
any of its siblings. Check only that single
device.
(d) !remove && !bridge_d3: D3 may now be allowed for the bridge if the
changed child was the only one blocking it.
Check all its siblings to verify that.
By checking beforehand if the changed child
is blocking D3, we may be able to skip
checking its siblings.
Currently we do not special-case option (a) and in case of option (c) we
gratuitously call pci_walk_bus(). Speed up the algorithm by adding these
optimizations. Reword the comments a bit in an attempt to improve clarity.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukas Wunner [Fri, 28 Oct 2016 08:52:06 +0000 (10:52 +0200)]
PCI: Autosense device removal in pci_bridge_d3_update()
The algorithm to update the flag indicating whether a bridge may go to D3
makes a few optimizations based on whether the update was caused by the
removal of a device on the one hand, versus the addition of a device or the
change of its D3cold flags on the other hand.
The information whether the update pertains to a removal is currently
passed in by the caller, but the function may as well determine that itself
by examining the device in question, thereby allowing for a considerable
simplification and reduction of the code.
Out of several options to determine removal, I've chosen the function
device_is_registered() because it's cheap: It merely returns the
dev->kobj.state_in_sysfs flag. That flag is set through device_add() when
the root bus is scanned and cleared through device_remove(). The call to
pci_bridge_d3_update() happens after each of these calls, respectively, so
the ordering is correct.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lukas Wunner [Fri, 28 Oct 2016 08:52:06 +0000 (10:52 +0200)]
PCI: Don't acquire ref on parent in pci_bridge_d3_update()
This function is always called with an existing pci_dev struct, which
holds a reference on the pci_bus struct it resides on, which in turn
holds a reference on pci_bus->bridge, which is the pci_dev's parent.
Hence there's no need to acquire an additional ref on the parent.
More specifically, the pci_dev exists until pci_destroy_dev() drops the
final reference on it, so all calls to pci_bridge_d3_update() must be
finished before that. It is arguably the caller's responsibility to ensure
that it doesn't call pci_bridge_d3_update() with a pci_dev that might
suddenly disappear, but in any case the existing callers are all safe:
- The call in pci_destroy_dev() happens before the call to put_device().
- The call in pci_bus_add_device() is synchronized with pci_destroy_dev()
using pci_lock_rescan_remove().
- The calls to pci_d3cold_disable() from the xhci and nouveau drivers
are safe because a ref on the pci_dev is held as long as it's bound to
a driver.
- The calls to pci_d3cold_enable() / pci_d3cold_disable() when modifying
the sysfs "d3cold_allowed" entry are also safe because kernfs_drain()
waits for existing sysfs users to finish before removing the entry,
and pci_destroy_dev() is called way after that.
No functional change intended.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bjorn Helgaas [Thu, 17 Nov 2016 22:11:39 +0000 (16:11 -0600)]
net/mlx4_core: Use device ID defines
We added a bunch of new Mellanox device ID definitions because they'll be
used by INTx quirks. Use them in the mlx4 ID table also so grep can find
both places. No functional change intended.
Shawn Lin [Mon, 14 Nov 2016 21:21:14 +0000 (15:21 -0600)]
of/pci: Add of_pci_get_max_link_speed() to parse max-link-speed from DT
This new helper function could be used by host drivers to get the limitaion
of max link speed provided by DT. If the property isn't assigned or is
invalid, it will return -EINVAL to the caller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rob Herring <robh@kernel.org>
Some of the host drivers have the requirement of knowing whether the EP
would never train at some link speed at all. For instance, on some boards,
the link won't train at 5 GT/s but the host driver still sacrifice some
cycles to wait for the result of training at 5 GT/s as the host could
actually support 5 GT/s. So we could parse this new property and make the
host drivers be aware of these cases.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rob Herring <robh@kernel.org>
Alan Stern [Fri, 21 Oct 2016 20:49:07 +0000 (16:49 -0400)]
USB: UHCI: report non-PME wakeup signalling for Intel hardware
The UHCI controllers in Intel chipsets rely on a platform-specific non-PME
mechanism for wakeup signalling. They can generate wakeup signals even
though they don't support PME.
We need to let the USB core know this so that it will enable runtime
suspend for UHCI controllers.
Alan Stern [Fri, 21 Oct 2016 20:45:38 +0000 (16:45 -0400)]
PCI: Check for PME in targeted sleep state
One some systems, the firmware does not allow certain PCI devices to be put
in deep D-states. This can cause problems for wakeup signalling, if the
device does not support PME# in the deepest allowed suspend state. For
example, Pierre reports that on his system, ACPI does not permit his xHCI
host controller to go into D3 during runtime suspend -- but D3 is the only
state in which the controller can generate PME# signals. As a result, the
controller goes into runtime suspend but never wakes up, so it doesn't work
properly. USB devices plugged into the controller are never detected.
If the device relies on PME# for wakeup signals but is not capable of
generating PME# in the target state, the PCI core should accurately report
that it cannot do wakeup from runtime suspend. This patch modifies the
pci_dev_run_wake() routine to add this check.
Reported-by: Pierre de Villemereuil <flyos@mailoo.org> Tested-by: Pierre de Villemereuil <flyos@mailoo.org> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> CC: stable@vger.kernel.org CC: Lukas Wunner <lukas@wunner.de>
Linus Torvalds [Sat, 15 Oct 2016 19:09:13 +0000 (12:09 -0700)]
Merge tag 'befs-v4.9-rc1' of git://github.com/luisbg/linux-befs
Pull befs fixes from Luis de Bethencourt:
"I recently took maintainership of the befs file system [0]. This is
the first time I send you a git pull request, so please let me know if
all the below is OK.
Salah Triki and myself have been cleaning the code and fixing a few
small bugs.
Sorry I couldn't send this sooner in the merge window, I was waiting
to have my GPG key signed by kernel members at ELCE in Berlin a few
days ago."
[0] https://lkml.org/lkml/2016/7/27/502
* tag 'befs-v4.9-rc1' of git://github.com/luisbg/linux-befs: (39 commits)
befs: befs: fix style issues in datastream.c
befs: improve documentation in datastream.c
befs: fix typos in datastream.c
befs: fix typos in btree.c
befs: fix style issues in super.c
befs: fix comment style
befs: add check for ag_shift in superblock
befs: dump inode_size superblock information
befs: remove unnecessary initialization
befs: fix typo in befs_sb_info
befs: add flags field to validate superblock state
befs: fix typo in befs_find_key
befs: remove unused BEFS_BT_PARMATCH
fs: befs: remove ret variable
fs: befs: remove in vain variable assignment
fs: befs: remove unnecessary *befs_sb variable
fs: befs: remove useless initialization to zero
fs: befs: remove in vain variable assignment
fs: befs: Insert NULL inode to dentry
fs: befs: Remove useless calls to brelse in befs_find_brun_dblindirect
...
Linus Torvalds [Sat, 15 Oct 2016 17:03:15 +0000 (10:03 -0700)]
Merge tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull gcc plugins update from Kees Cook:
"This adds a new gcc plugin named "latent_entropy". It is designed to
extract as much possible uncertainty from a running system at boot
time as possible, hoping to capitalize on any possible variation in
CPU operation (due to runtime data differences, hardware differences,
SMP ordering, thermal timing variation, cache behavior, etc).
At the very least, this plugin is a much more comprehensive example
for how to manipulate kernel code using the gcc plugin internals"
* tag 'gcc-plugins-v4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
latent_entropy: Mark functions with __latent_entropy
gcc-plugins: Add latent_entropy plugin
Linus Torvalds [Sat, 15 Oct 2016 16:26:12 +0000 (09:26 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Linus Torvalds [Sat, 15 Oct 2016 16:20:54 +0000 (09:20 -0700)]
Merge tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few trivial small fixes"
* tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: line6: fix a crash in line6_hwdep_write()
ALSA: seq: fix passing wrong pointer in function call of compatibility layer
ALSA: hda - Fix a failure of micmute led when having multi adcs
ALSA: line6: Fix POD X3 Live audio input
Linus Torvalds [Sat, 15 Oct 2016 01:19:05 +0000 (18:19 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more misc uaccess and vfs updates from Al Viro:
"The rest of the stuff from -next (more uaccess work) + assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
score: traps: Add missing include file to fix build error
fs/super.c: don't fool lockdep in freeze_super() and thaw_super() paths
fs/super.c: fix race between freeze_super() and thaw_super()
overlayfs: Fix setting IOP_XATTR flag
iov_iter: kernel-doc import_iovec() and rw_copy_check_uvector()
blackfin: no access_ok() for __copy_{to,from}_user()
arm64: don't zero in __copy_from_user{,_inatomic}
arm: don't zero in __copy_from_user_inatomic()/__copy_from_user()
arc: don't leak bits of kernel stack into coredump
alpha: get rid of tail-zeroing in __copy_user()
Linus Torvalds [Sat, 15 Oct 2016 00:47:31 +0000 (17:47 -0700)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Including:
- nine bug fixes for stable. Some of these we found at the recent two
weeks of SMB3 test events/plugfests.
- significant improvements in reconnection (e.g. if server or network
crashes) especially when mounted with "persistenthandles" or to
server which advertises Continuous Availability on the share.
- a new mount option "idsfromsid" which improves POSIX compatibility
in some cases (when winbind not configured e.g.) by better (and
faster) fetching uid/gid from acl (when "cifsacl" mount option is
enabled). NB: we are almost complete work on "cifsacl" (querying
mode/uid/gid from ACL) for SMB3, but SMB3 support for cifsacl is
not included in this set.
- improved handling for SMB3 "credits" (even if server is buggy)
Still working on two sets of changes:
- cifsacl enablement for SMB3
- cleanup of RFC1001 length calculation (so we can handle encryption
and multichannel and RDMA)
And a couple of new bugs were reported recently (unrelated to above)
so will probably have another merge request next week"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
CIFS: Retrieve uid and gid from special sid if enabled
CIFS: Add new mount option to set owner uid and gid from special sids in acl
CIFS: Reset read oplock to NONE if we have mandatory locks after reopen
CIFS: Fix persistent handles re-opening on reconnect
SMB2: Separate RawNTLMSSP authentication from SMB2_sess_setup
SMB2: Separate Kerberos authentication from SMB2_sess_setup
Expose cifs module parameters in sysfs
Cleanup missing frees on some ioctls
Enable previous version support
Do not send SMB3 SET_INFO request if nothing is changing
SMB3: Add mount parameter to allow user to override max credits
fs/cifs: reopen persistent handles on reconnect
Clarify locking of cifs file and tcon structures and make more granular
Fix regression which breaks DFS mounting
fs/cifs: keep guid when assigning fid to fileinfo
SMB3: GUIDs should be constructed as random but valid uuids
Set previous session id correctly on SMB3 reconnect
cifs: Limit the overall credit acquired
Display number of credits available
Add way to query creation time of file via cifs xattr
...
Linus Torvalds [Sat, 15 Oct 2016 00:44:56 +0000 (17:44 -0700)]
Merge branch 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Some fixes from Omar and Dave Sterba for our new free space tree.
This isn't heavily used yet, but as we move toward making it the new
default we wanted to nail down an endian bug"
* 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: tests: uninline member definitions in free_space_extent
btrfs: tests: constify free space extent specs
Btrfs: expand free space tree sanity tests to catch endianness bug
Btrfs: fix extent buffer bitmap tests on big-endian systems
Btrfs: catch invalid free space trees
Btrfs: fix mount -o clear_cache,space_cache=v2
Btrfs: fix free space tree bitmaps on big-endian systems
fs/super.c: don't fool lockdep in freeze_super() and thaw_super() paths
sb_wait_write()->percpu_rwsem_release() fools lockdep to avoid the
false-positives. Now that xfs was fixed by Dave's commit dbad7c993053
("xfs: stop holding ILOCK over filldir callbacks") we can remove it and
change freeze_super() and thaw_super() to run with s_writers.rw_sem locks
held; we add two trivial helpers for that, lockdep_sb_freeze_release()
and lockdep_sb_freeze_acquire().
xfstests-dev/check `grep -il freeze tests/*/???` does not trigger any
warning from lockdep.
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sat, 15 Oct 2016 00:23:33 +0000 (17:23 -0700)]
Merge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs updates from Miklos Szeredi:
"This update contains fixes to the "use mounter's permission to access
underlying layers" area, and miscellaneous other fixes and cleanups.
No new features this time"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: use vfs_get_link()
vfs: add vfs_get_link() helper
ovl: use generic_readlink
ovl: explain error values when removing acl from workdir
ovl: Fix info leak in ovl_lookup_temp()
ovl: during copy up, switch to mounter's creds early
ovl: lookup: do getxattr with mounter's permission
ovl: copy_up_xattr(): use strnlen
fs/super.c: fix race between freeze_super() and thaw_super()
Change thaw_super() to check frozen != SB_FREEZE_COMPLETE rather than
frozen == SB_UNFROZEN, otherwise it can race with freeze_super() which
drops sb->s_umount after SB_FREEZE_WRITE to preserve the lock ordering.
In this case thaw_super() will wrongly call s_op->unfreeze_fs() before
it was actually frozen, and call sb_freeze_unlock() which leads to the
unbalanced percpu_up_write(). Unfortunately lockdep can't detect this,
so this triggers misc BUG_ON()'s in kernel/rcu/sync.c.
Reported-and-tested-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Vivek Goyal [Fri, 14 Oct 2016 01:03:36 +0000 (03:03 +0200)]
overlayfs: Fix setting IOP_XATTR flag
ovl_fill_super calls ovl_new_inode to create a root inode for the new
superblock before initializing sb->s_xattr. This wrongly causes
IOP_XATTR to be cleared in i_opflags of the new inode, causing SELinux
to log the following message:
SELinux: (dev overlay, type overlay) has no xattr support
Fix this by initializing sb->s_xattr and similar fields before calling
ovl_new_inode.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Vegard Nossum [Sat, 8 Oct 2016 09:18:07 +0000 (11:18 +0200)]
iov_iter: kernel-doc import_iovec() and rw_copy_check_uvector()
Both import_iovec() and rw_copy_check_uvector() take an array
(typically small and on-stack) which is used to hold an iovec array copy
from userspace. This is to avoid an expensive memory allocation in the
fast path (i.e. few iovec elements).
The caller may have to check whether these functions actually used
the provided buffer or allocated a new one -- but this differs between
the too. Let's just add a kernel doc to clarify what the semantics are
for each function.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Fri, 14 Oct 2016 22:17:12 +0000 (15:17 -0700)]
Merge tag 'linux-kselftest-4.9-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest updates from Shuah Khan:
"This update consists of:
- Fixes and improvements to existing tests
- Moving code from Documentation to selftests, samples, and tools:
* Moves dnotify_test, prctl, ptp, vDSO, ia64, watchdog, and
networking tests from Documentation to selftests.
* Moves mic/mpssd, misc-devices/mei, timers, watchdog, auxdisplay,
and blackfin examples from Documentation to samples.
* Moves accounting, laptops/dslm, and pcmcia/crc32hash tools from
Documentation to tools.
* Deletes BUILD_DOCSRC and its dependencies"
* tag 'linux-kselftest-4.9-rc1-update' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (21 commits)
selftests/futex: Check ANSI terminal color support
Doc: update 00-INDEX files to reflect the runnable code move
samples: move blackfin gptimers-example from Documentation
tools: move pcmcia crc32hash tool from Documentation
tools: move laptops dslm tool from Documentation
tools: move accounting tool from Documentation
samples: move auxdisplay example code from Documentation
samples: move watchdog example code from Documentation
samples: move timers example code from Documentation
samples: move misc-devices/mei example code from Documentation
samples: move mic/mpssd example code from Documentation
selftests: Move networking/timestamping from Documentation
selftests: move watchdog tests from Documentation/watchdog
selftests: move ia64 tests from Documentation/ia64
selftests: move vDSO tests from Documentation/vDSO
selftests: move ptp tests from Documentation/ptp
selftests: move prctl tests from Documentation/prctl
selftests: move dnotify_test from Documentation/filesystems
selftests/timers: Add missing error code assignment before test
selftests/zram: replace ZRAM_LZ4_COMPRESS
...
Linus Torvalds [Fri, 14 Oct 2016 22:03:08 +0000 (15:03 -0700)]
Merge branch 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull misc kbuild changes from Michal Marek:
"Just a few patches on the kbuild.git#misc branch this time:
- New Coccinelle patch by Nicholas Mc Guire
- Existing patch fixes by Julia Lawall
- Minor comment fix by Markus Elfring"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Coccinelle: flag conditions with no effect
scripts/coccicheck: Update reference for the corresponding documentation
Coccinelle: pm_runtime: ensure relevance of pm_runtime reports
Coccinelle: limit memdup_user transformation to GFP_KERNEL case
Linus Torvalds [Fri, 14 Oct 2016 21:26:58 +0000 (14:26 -0700)]
Merge branch 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
- EXPORT_SYMBOL for asm source by Al Viro.
This does bring a regression, because genksyms no longer generates
checksums for these symbols (CONFIG_MODVERSIONS). Nick Piggin is
working on a patch to fix this.
Plus, we are talking about functions like strcpy(), which rarely
change prototypes.
- Fixes for PPC fallout of the above by Stephen Rothwell and Nick
Piggin
- fixdep speedup by Alexey Dobriyan.
- preparatory work by Nick Piggin to allow architectures to build with
-ffunction-sections, -fdata-sections and --gc-sections
- CONFIG_THIN_ARCHIVES support by Stephen Rothwell
- fix for filenames with colons in the initramfs source by me.
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (22 commits)
initramfs: Escape colons in depfile
ppc: there is no clear_pages to export
powerpc/64: whitelist unresolved modversions CRCs
kbuild: -ffunction-sections fix for archs with conflicting sections
kbuild: add arch specific post-link Makefile
kbuild: allow archs to select link dead code/data elimination
kbuild: allow architectures to use thin archives instead of ld -r
kbuild: Regenerate genksyms lexer
kbuild: genksyms fix for typeof handling
fixdep: faster CONFIG_ search
ia64: move exports to definitions
sparc32: debride memcpy.S a bit
[sparc] unify 32bit and 64bit string.h
sparc: move exports to definitions
ppc: move exports to definitions
arm: move exports to definitions
s390: move exports to definitions
m68k: move exports to definitions
alpha: move exports to actual definitions
x86: move exports to actual definitions
...
Linus Torvalds [Fri, 14 Oct 2016 21:11:22 +0000 (14:11 -0700)]
Merge tag 'docs-4.9-2' of git://git.lwn.net/linux
Pull one more documentation update from Jonathan Corbet:
"A single commit converting the mac80211 DocBook template over to
Sphinx. Only 32 more to go..."
* tag 'docs-4.9-2' of git://git.lwn.net/linux:
docs-rst: sphinxify 802.11 documentation
Linus Torvalds [Fri, 14 Oct 2016 20:43:08 +0000 (13:43 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma qedr RoCE driver from Doug Ledford:
"Early on in the merge window I mentioned I had a backlog of new
drivers waiting to be reviewed and that, in addition to the hns-roce
driver, I wanted to get possible a couple more reviewed. I ended up
only having the time to complete one of the additional drivers.
During Dave Miller's pull request this go around, there were a series
of 9 patches to the QLogic qed net driver that add basic support for a
paired RoCE driver. That support is currently not functional because
it is missing the matching RoCE driver in the RDMA subsystem. I
managed to finish that review. However, because it goes against part
of Dave's net pull, and a part that was accepted a day or two after
the merge window opened, to apply cleanly it has to be applied to
either the tip of Dave's net branch, or as I did in this case, I just
applied it to your master after you had taken Dave's pull request."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
qedr: Add events support and register IB device
qedr: Add GSI support
qedr: Add LL2 RoCE interface
qedr: Add support for data path
qedr: Add support for memory registeration verbs
qedr: Add support for QP verbs
qedr: Add support for PD,PKEY and CQ verbs
qedr: Add support for user context verbs
qedr: Add support for RoCE HW init
qedr: Add RoCE driver framework
Linus Torvalds [Fri, 14 Oct 2016 20:35:05 +0000 (13:35 -0700)]
Merge tag 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"This merge window was the first where Huawei had to try and coordinate
their patches between their net driver and their new roce driver
(similar to mlx4 and mlx5).
They didn't do horribly, but there were some issues (and we knew that
because they simply didn't know what to do in the beginning). As a
result, I had a set of patches that depended on some patches that
normally would have come to you via Dave's tree. Those patches have
been on netdev@ for a while, so I got Dave to give me his approval to
send them to you. As such, the other 29 patches I had behind them are
also now ready to go.
This catches the hns and hns-roce drivers up to current, and for
future patches we are working with them to get them up to speed on how
to do joint driver development so that they don't have these sorts of
cross tree dependency issues again. BTW, Dave gave me permission to
add his Acked-by: to the patches against the net tree, but I've had
this branch through 0day (but not linux-next since it was off by
itself) and I didn't want to rebase the series just to add Dave's ack
for the 8 patches in the net area.
Updates to the hns drivers:
- Small patch set for hns net driver that the roce patches depend on
- Various fixes to the hns-roce driver
- Add connection manager support to the hns-roce driver"
* tag 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (36 commits)
IB/hns: Fix for removal of redundant code
IB/hns: Delete the redundant lines in hns_roce_v1_m_qp()
IB/hns: Fix the bug when platform_get_resource() exec fail
IB/hns: Update the rq head when modify qp state
IB/hns: Cq has not been freed
IB/hns: Validate mtu when modified qp
IB/hns: Some items of qpc need to take user param
IB/hns: The Ack timeout need a lower limit value
IB/hns: Return bad wr while post send failed
IB/hns: Fix bug of memory leakage for registering user mr
IB/hns: Modify the init of iboe lock
IB/hns: Optimize code of aeq and ceq interrupt handle and fix the bug of qpn
IB/hns: Delete the sqp_start from the structure hns_roce_caps
IB/hns: Fix bug of clear hem
IB/hns: Remove unused parameter named qp_type
IB/hns: Simplify function of pd alloc and qp alloc
IB/hns: Fix bug of using uninit refcount and free
IB/hns: Remove parameters of resize cq
IB/hns: Remove unused parameters in some functions
IB/hns: Add node_guid definition to the bindings document
...
Linus Torvalds [Fri, 14 Oct 2016 20:19:30 +0000 (13:19 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull some more input subsystem updates from Dmitry Torokhov:
"An update to the ALPS driver to support the V8 protocol with
touchstick, a change for i8042 to skip selftest on many Asus laptops
which helps to keep their touchpads working after resume, and a couple
other driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - skip selftest on ASUS laptops
Input: melfas_mip4 - add ic_name sysfs attribute
Input: melfas_mip4 - add maintainer information
Input: melfas_mip4 - add devicetree binding documentations
Input: elantech - add Fujitsu Lifebook E556 to force crc_enabled
Input: synaptics-rmi4 - fix error handling in I2C transport driver
Input: synaptics-rmi4 - fix error handling in SPI transport driver
Input: ALPS - add V8 protocol documentation
Input: ALPS - set DualPoint flag for 74 03 28 devices
Input: ALPS - allow touchsticks to report pressure
Input: ALPS - handle 0-pressure 1F events
Input: ALPS - add touchstick support for SS5 hardware
Input: elantech - force needed quirks on Fujitsu H760
Input: elantech - fix Lenovo version typo
Drivers:
- ac100: support clock-output-names
- cmos: properly handle ACPI alarms and quirky BIOSes and other fixes
- ds1307: fix century bit support while staying comaptible with
previous behaviour by default
- ds1347: switch to regmap
- isl12057 is now handled by ds1307
- omap: support external wakeup
- rv8803: allow to disable voltage drop detection"
* tag 'rtc-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (25 commits)
rtc: rv8803: set VDETOFF and SWOFF via device tree
dt/bindings: Add bindings for Micro Crystal rv8803
devicetree: Add Micro Crystal AG vendor id
rtc: cmos: avoid unused function warning
rtc: ac100: Add NULL checking for devm_kzalloc call
rtc: ds1347: changed raw spi calls to register map calls
rtc: cmos: Restore alarm after resume
rtc: cmos: Clear ACPI-driven alarms upon resume
rtc: omap: Support ext_wakeup configuration
rtc: cmos: Initialize hpet timer before irq is registered
rtc: asm9260: rework locking
rtc: asm9260: allow COMPILE_TEST
rtc: constify rtc_class_ops structures
rtc: ac100: support clock-output-names in device tree binding
rtc: rx6110: remove owner assignment
rtc: pic32: Delete owner assignment
rtc: bq32k: Fix handling of oscillator failure flag
rtc: bq32k: Use correct mask name for 'minutes' register.
rtc: sysfs: fix a cast removing the const attribute
Documentation: dt: Intersil isl12057 is not a trivial device
...
Linus Torvalds [Fri, 14 Oct 2016 20:09:41 +0000 (13:09 -0700)]
Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"A small update pull request from I2C.
This adds one comment to a change we did in this merge window to
handle lockdep better, and pulls in a branch which should have been in
4.8 already improving DT support for I2C"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
gpio: pca953x: add a comment explaining the need for a lockdep subclass
i2c: core: Add support for 'i2c-bus' subnode
dt-bindings: i2c: Add support for 'i2c-bus' subnode
Linus Torvalds [Fri, 14 Oct 2016 19:50:05 +0000 (12:50 -0700)]
Merge tag 'acpi-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"This includes a couple of fixes needed after recent changes, two ACPI
driver fixes (fan and "Processor Aggregator"), an update of the ACPI
device properties handling code and a new MAINTAINERS entry for ACPI
on ARM64.
Specifics:
- Fix an unused function warning that started to appear after recent
changes in the ACPI EC driver (Eric Biggers).
- Fix the KERN_CONT usage in acpi_os_vprintf() that has become
(particularly) annoying recently (Joe Perches).
- Fix the fan status checking in the ACPI fan driver to avoid
returning incorrect error codes sometimes (Srinivas Pandruvada).
- Fix the ACPI Processor Aggregator driver (PAD) to always let the
special processor_aggregator driver from Xen take over when running
as Xen dom0 (Juergen Gross).
- Update the handling of reference device properties in ACPI by
allowing empty rows ("holes") to appear in reference property lists
(Mika Westerberg).
- Add a new MAINTAINERS entry for ACPI on ARM64 (Lorenzo Pieralisi)"
* tag 'acpi-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
acpi_os_vprintf: Use printk_get_level() to avoid unnecessary KERN_CONT
ACPI / PAD: don't register acpi_pad driver if running as Xen dom0
ACPI / property: Allow holes in reference properties
MAINTAINERS: Add ARM64-specific ACPI maintainers entry
ACPI / EC: Fix unused function warning when CONFIG_PM_SLEEP=n
ACPI / fan: Fix error reading cur_state
projects / linux-beck.git / log