Matt Carlson [Wed, 27 Jul 2011 14:20:53 +0000 (14:20 +0000)]
tg3: Break larger frags into 4k chunks for 5719
The 5719 has bug where RDMAs larger than 4k can cause problems. This
patch works around the problem by dividing larger DMA requests into
something the hardware can handle.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:52 +0000 (14:20 +0000)]
tg3: Add tx BD budgeting code
As the driver breaks large skb fragments into smaller submissions to the
hardware, there is a new danger that BDs might get exhausted before all
fragments have been mapped. This patch adds code to make sure tx BDs
aren't oversubscribed and flag the condition if it happens.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:51 +0000 (14:20 +0000)]
tg3: Consolidate code that calls tg3_tx_set_bd()
This patch consolidates all code that populates tx BDs into a single
routine. Setting tx BDs needs to be more carefully controlled to see if
workarounds need to be applied.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:50 +0000 (14:20 +0000)]
tg3: Add partial fragment unmapping code
The following patches are going to break skb fragments into smaller
sizes. This patch attempts to make the change easier to digest by only
addressing the skb teardown portion.
The patch modifies the driver to skip over any BDs that have a flag set
that indicates the BD isn't the beginning of an skb fragment. Such BDs
were a result of segmentation and do not need a pci_unmap_page() call.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:49 +0000 (14:20 +0000)]
tg3: Generalize tg3_skb_error_unmap()
In the following patches, unmapping skb fragments will get just as
complicated as mapping them. This patch generalizes
tg3_skb_error_unmap() and makes it the one-stop-shop for skb unmapping.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:48 +0000 (14:20 +0000)]
tg3: Remove short DMA check for 1st fragment
The first fragment of an skb should always be greater than 8 bytes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:47 +0000 (14:20 +0000)]
tg3: Simplify tx bd assignments
In the following patches, the process the driver will use to assign skb
fragments to transmit BDs will get more complicated. To prepare for
that new code, this patch seeks to simplify how transmit BDs are
populated. It does this by separating the code that assigns the BD
members from the logic that controls how the fields are set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Wed, 27 Jul 2011 14:20:46 +0000 (14:20 +0000)]
tg3: Reintroduce tg3_tx_ring_info
The following patches will require the use of an additional flag in the
ring_info structure. The use of this flag is tx path specific, so this
patch defines a specialized ring_info structure.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Reviewed-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek [Wed, 27 Jul 2011 10:09:26 +0000 (10:09 +0000)]
bonding: reduce noise during init
On Tue, Jul 26, 2011 at 05:40:27PM -0700, Joe Perches wrote:
> On Tue, 2011-07-26 at 17:37 -0700, Jay Vosburgh wrote:
> > Joe Perches <joe@perches.com> wrote:
> > >I'd prefer you don't separate the format string
> > >into multiple pieces.
> > Why not? To me, it looks easier to read split into sections
> > that don't wrap lines.
>
> Harder to grep for a dmesg and the
> defect rate of these split formats is
> typically higher than single strings
> because of bad spacing between string
> segments.
>
I noticed that you took some time back in late 2009 to 'consolidate' the
split format-strings present in the bonding driver at the time and I've
decided I'm fine to leave them the way they are. The main point of my
patch was to change the output and I would like to get that included.
Here is my updated patch...
Subject: [PATCH net-next-2.6 v2] bonding: reduce noise during init
Many are using sysfs to configure bonding rather than module options, so
there is no need for bonding to throw this warning in normal cases.
Keep the message around when debugging is enabled as it might be useful
for someone desperate enough to enable debugging, but eliminate it
otherwise.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek [Tue, 26 Jul 2011 11:12:27 +0000 (11:12 +0000)]
bonding: fix string comparison errors
When a bond contains a device where one name is the subset of another
(eth1 and eth10, for example), one cannot properly set the primary
device or the currently active device.
This was reported and based on work by Takuma Umeya. I also verified
the problem and tested that this fix resolves it.
V2: A few did not like the the current code or my changes, so I
refactored bonding_store_primary and bonding_store_active_slave to be a
bit cleaner, dropped the use of strnicmp since we did not really need
the comparison to be case insensitive, and formatted the input string
from sysfs so a comparison to IFNAMSIZ could be used.
I also discovered an error in bonding_store_active_slave that would
modify bond->primary_slave rather than bond->curr_active_slave before
forcing the bonding driver to choose a new active slave.
V3: Actually sending the proper patch....
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Reported-by: Takuma Umeya <tumeya@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 26 Jul 2011 06:05:38 +0000 (06:05 +0000)]
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
After the last patch, We are left in a state in which only drivers calling
ether_setup have IFF_TX_SKB_SHARING set (we assume that drivers touching real
hardware call ether_setup for their net_devices and don't hold any state in
their skbs. There are a handful of drivers that violate this assumption of
course, and need to be fixed up. This patch identifies those drivers, and marks
them as not being able to support the safe transmission of skbs by clearning the
IFF_TX_SKB_SHARING flag in priv_flags
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: Karsten Keil <isdn@linux-pingi.de> CC: "David S. Miller" <davem@davemloft.net> CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Patrick McHardy <kaber@trash.net> CC: Krzysztof Halasa <khc@pm.waw.pl> CC: "John W. Linville" <linville@tuxdriver.com> CC: Greg Kroah-Hartman <gregkh@suse.de> CC: Marcel Holtmann <marcel@holtmann.org> CC: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 26 Jul 2011 06:05:37 +0000 (06:05 +0000)]
net: add IFF_SKB_TX_SHARED flag to priv_flags
Pktgen attempts to transmit shared skbs to net devices, which can't be used by
some drivers as they keep state information in skbs. This patch adds a flag
marking drivers as being able to handle shared skbs in their tx path. Drivers
are defaulted to being unable to do so, but calling ether_setup enables this
flag, as 90% of the drivers calling ether_setup touch real hardware and can
handle shared skbs. A subsequent patch will audit drivers to ensure that the
flag is set properly
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Jiri Pirko <jpirko@redhat.com> CC: Robert Olsson <robert.olsson@its.uu.se> CC: Eric Dumazet <eric.dumazet@gmail.com> CC: Alexey Dobriyan <adobriyan@gmail.com> CC: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason, when rxaccel is disabled, NV_RX3_VLAN_TAG_PRESENT is
still set and some pseudorandom vids appear. So check for
NETIF_F_HW_VLAN_RX as well. Also set correctly hw_features and set vlan
mode on probe.
Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
commit 87c288c6e9aa31720b72e2bc2d665e24e1653c3e "gianfar: do vlan cleanup" has two issues:
# permutation of rx and tx flags
# enabling vlan tag insertion by default (this leads to unusable connections on some configurations)
If VLAN insertion is requested (via ethtool) it will be set at an other point ...
Signed-off-by: Sebastian Poehn <sebastian.poehn@belden.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Wed, 27 Jul 2011 13:16:28 +0000 (06:16 -0700)]
gro: Only reset frag0 when skb can be pulled
Currently skb_gro_header_slow unconditionally resets frag0 and
frag0_len. However, when we can't pull on the skb this leaves
the GRO fields in an inconsistent state.
This patch fixes this by only resetting those fields after the
pskb_may_pull test.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Mihai Moldovan [Mon, 25 Jul 2011 09:18:58 +0000 (11:18 +0200)]
wireless: fix a typo in ignore_reg_update
Just a typo fix changing regulaotry to regulatory.
Signed-off-by: Mihai Moldovan <ionic@ionic.de> CC: John W. Linville <linville@tuxdriver.com> CC: Mohammed Shafi <shafi.wireless@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've fixed the last issue with BCMA support which caused memory
corruption on loading and unloading b43. Support for BCMA in b43 was
tested with 14e4:4353, 14e4:4357, 14e4:4727 and 14e4:4331. First two
cards (BCM43224 and BCM43225) are supported.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sven Neumann [Tue, 12 Jul 2011 13:52:07 +0000 (15:52 +0200)]
cfg80211: really ignore the regulatory request
At the beginning of wiphy_update_regulatory() a check is performed
whether the request is to be ignored. Then the request is sent to
the driver nevertheless. This happens even if last_request points
to NULL, leading to a crash in the driver:
[<bf01d864>] (lbs_set_11d_domain_info+0x28/0x1e4 [libertas]) from [<c03b714c>] (wiphy_update_regulatory+0x4d0/0x4f4)
[<c03b714c>] (wiphy_update_regulatory+0x4d0/0x4f4) from [<c03b4008>] (wiphy_register+0x354/0x420)
[<c03b4008>] (wiphy_register+0x354/0x420) from [<bf01b17c>] (lbs_cfg_register+0x80/0x164 [libertas])
[<bf01b17c>] (lbs_cfg_register+0x80/0x164 [libertas]) from [<bf020e64>] (lbs_start_card+0x20/0x88 [libertas])
[<bf020e64>] (lbs_start_card+0x20/0x88 [libertas]) from [<bf02cbd8>] (if_sdio_probe+0x898/0x9c0 [libertas_sdio])
Fix this by returning early. Also remove the out: label as it is
not any longer needed.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com> Cc: linux-wireless@vger.kernel.org Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Daniel Mack <daniel@zonque.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zoltan Kiss [Sun, 24 Jul 2011 13:09:30 +0000 (13:09 +0000)]
IPv4: Send gratuitous ARP for secondary IP addresses also
If a device event generates gratuitous ARP messages, only primary
address is used for sending. This patch iterates through the whole
list. Tested with 2 IP addresses configuration on bonding interface.
Signed-off-by: Zoltan Kiss <schaman@sch.bme.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: Do not leave router anycast address for /127 prefixes.
Original commit 2bda8a0c8af... "Disable router anycast
address for /127 prefixes" says:
| No need for matching code in addrconf_leave_anycast() as it
| will silently ignore any attempt to leave an unknown anycast
| address.
After analysis, because 1) we may add two or more prefixes on the
same interface, or 2)user may have manually joined that anycast,
we may hit chances to have anycast address which as if we had
generated one by /127 prefix and we should not leave from subnet-
router anycast address unconditionally.
CC: Bjørn Mork <bjorn@mork.no> CC: Brian Haley <brian.haley@hp.com> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (lm78) Become the maintainer
hwmon: (lm78) Make ISA interface depend on CONFIG_ISA
hwmon: (lm78) Avoid forward declarations
hwmon: (sht15) Correct a comment mistake
hwmon: (max1111) Avoid extra memory allocations
hwmon: (it87) Add chassis intrusion detection support
hwmon: (via-cputemp) Add VID reporting support
hwmon-vid: Add support for VIA family 6 model D CPU
hwmon: New driver sch5636
hwmon: (sch5627) Factor out some code shared with sch5636 driver
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: take the ACL checks to common code
bury posix_acl_..._masq() variants
kill boilerplates around posix_acl_create_masq()
generic_acl: no need to clone acl just to push it to set_cached_acl()
kill boilerplate around posix_acl_chmod_masq()
reiserfs: cache negative ACLs for v1 stat format
xfs: cache negative ACLs if there is no attribute fork
9p: do no return 0 from ->check_acl without actually checking
vfs: move ACL cache lookup into generic code
CIFS: Fix oops while mounting with prefixpath
xfs: Fix wrong return value of xfs_file_aio_write
fix devtmpfs race
caam: don't pass bogus S_IFCHR to debugfs_create_...()
get rid of create_proc_entry() abuses - proc_mkdir() is there for purpose
asus-wmi: ->is_visible() can't return negative
fix jffs2 ACLs on big-endian with 16bit mode_t
9p: close ACL leaks
ocfs2_init_acl(): fix a leak
VFS : mount lock scalability for internal mounts
Jean Delvare [Mon, 25 Jul 2011 19:46:11 +0000 (21:46 +0200)]
hwmon: (lm78) Make ISA interface depend on CONFIG_ISA
We should only include support for the ISA interface of the LM78/LM79
if CONFIG_ISA is set. Not only this makes the driver somewhat smaller
on most architectures, but this also avoids poking at random I/O
ports on these architectures.
This is very similiar to what was done for the w83781d driver in
October 2008.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Dean Nelson <dnelson@redhat.com>
Hans de Goede [Mon, 25 Jul 2011 19:46:09 +0000 (21:46 +0200)]
hwmon: New driver sch5636
This patch adds a new driver for SMSC SCH5636 Super I/O chips.
The chips include an embedded microcontroller for hardware monitoring
solutions, allowing motherboard manufacturers to create their own
custom hwmon solution based upon the SCH5636.
Currently the sch5636 driver only supports the Fujitsu Theseus SCH5636
based hwmon solution. The sch5636 driver runs a sanity check on
loading to ensure it is dealing with a Fujitsu Theseus and not with
another custom SCH5636 based hwmon solution.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Merge branch 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
ARM: S3C24XX: Use generic s3c_set_platdata for devices
ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
ARM: SAMSUNG: Use generic s3c_set_platdata for FB
ARM: SAMSUNG: Use generic s3c_set_platdata for TS
ARM: S3C64XX: Add PWM backlight support on SMDK6410
ARM: S5P64X0: Add PWM backlight support on SMDK6450
ARM: S5P64X0: Add PWM backlight support on SMDK6440
ARM: S5PC100: Add PWM backlight support on SMDKC100
ARM: S5PV210: Add PWM backlight support on SMDKV210
ARM: EXYNOS4: Add PWM backlight support on SMDKC210
ARM: EXYNOS4: Add PWM backlight support on SMDKV310
ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
...
Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
Merge branch 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Allow i2c_add_numbered_adapter() to assign a bus id
i2c-ali1535: Fix style issues
Replace the ->check_acl method with a ->get_acl method that simply reads an
ACL from disk after having a cache miss. This means we can replace the ACL
checking boilerplate code with a single implementation in namei.c.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 23 Jul 2011 07:10:32 +0000 (03:10 -0400)]
kill boilerplates around posix_acl_create_masq()
new helper: posix_acl_create(&acl, gfp, mode_p). Replaces acl with
modified clone, on failure releases acl and replaces with NULL.
Returns 0 or -ve on error. All callers of posix_acl_create_masq()
switched.
Al Viro [Sat, 23 Jul 2011 04:18:02 +0000 (00:18 -0400)]
kill boilerplate around posix_acl_chmod_masq()
new helper: posix_acl_chmod(&acl, gfp, mode). Replaces acl with modified
clone or with NULL if that has failed; returns 0 or -ve on error. All
callers of posix_acl_chmod_masq() switched to that - they'd been doing
exactly the same thing.
xfs: cache negative ACLs if there is no attribute fork
Always set up a negative ACL cache entry if the inode doesn't have an
attribute fork. That behaves much better than doing this check inside
->check_acl.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
9p: do no return 0 from ->check_acl without actually checking
If we do not want to use ACLs we at least need to perform normal Unix
permission checks. From the comment I'm not quite sure that's what
is intended, but if 0p wants to do permission checks entirely on the
server it needs to do so in ->permission, not in ->check_acl.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This moves logic for checking the cached ACL values from low-level
filesystems into generic code. The end result is a streamlined ACL
check that doesn't need to load the inode->i_op->check_acl pointer at
all for the common cached case.
The filesystems also don't need to check for a non-blocking RCU walk
case in their acl_check() functions, because that is all handled at a
VFS layer.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The problem is that lookup_one_len calls __lookup_hash
with nd pointer as NULL. Then __lookup_hash calls
do_revalidate in the case when dentry exists and we end
up with NULL pointer deference in cifs_d_revalidate:
if (nd->flags & LOOKUP_RCU)
return -ECHILD;
Fix this by checking nd for NULL.
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The fsync prototype change commit 02c24a82187d accidentally overwrote
the ssize_t return value of xfs_file_aio_write with 0 for SYNC type
writes. Fix this by checking if an error occured when calling
xfs_file_fsync and only change the return value in this case.
In addition xfs_file_fsync actually returns a normal negative error, so
fix this, too.
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Mon, 25 Jul 2011 18:15:50 +0000 (14:15 -0400)]
fix devtmpfs race
After we's done complete(&req->done), there's nothing to prevent the
scope containing *req from being gone and *req overwritten by any
kind of junk. So we must read req->next before that...
Merge branch 'for-3.1/drivers' of git://git.kernel.dk/linux-block
* 'for-3.1/drivers' of git://git.kernel.dk/linux-block:
cciss: do not attempt to read from a write-only register
xen/blkback: Add module alias for autoloading
xen/blkback: Don't let in-flight requests defer pending ones.
bsg: fix address space warning from sparse
bsg: remove unnecessary conditional expressions
bsg: fix bsg_poll() to return POLLOUT properly
Merge branch 'for-3.1/core' of git://git.kernel.dk/linux-block
* 'for-3.1/core' of git://git.kernel.dk/linux-block: (24 commits)
block: strict rq_affinity
backing-dev: use synchronize_rcu_expedited instead of synchronize_rcu
block: fix patch import error in max_discard_sectors check
block: reorder request_queue to remove 64 bit alignment padding
CFQ: add think time check for group
CFQ: add think time check for service tree
CFQ: move think time check variables to a separate struct
fixlet: Remove fs_excl from struct task.
cfq: Remove special treatment for metadata rqs.
block: document blk_plug list access
block: avoid building too big plug list
compat_ioctl: fix make headers_check regression
block: eliminate potential for infinite loop in blkdev_issue_discard
compat_ioctl: fix warning caused by qemu
block: flush MEDIA_CHANGE from drivers on close(2)
blk-throttle: Make total_nr_queued unsigned
block: Add __attribute__((format(printf...) and fix fallout
fs/partitions/check.c: make local symbols static
block:remove some spare spaces in genhd.c
block:fix the comment error in blkdev.h
...
Randy Dunlap [Sun, 24 Jul 2011 18:39:14 +0000 (11:39 -0700)]
iomap: make IOPORT/PCI mapping functions conditional
When CONFIG_PCI is not enabled, CONFIG_EISA=y, and CONFIG_GENERIC_IOMAP=y,
drivers/net/3c59x.c build fails due to a recent small change to
<asm-generic/iomap.h> that surrounds pci_iomap() and pci_iounmap() with
#ifdef CONFIG_PCI/#endif.
Since that patch to iomap.h looks correct, add stubs for pci_iomap() and
pci_iounmap() with CONFIG_PCI is not enabled to fix the build errors.
drivers/net/3c59x.c:1026: error: implicit declaration of function 'pci_iomap'
drivers/net/3c59x.c:1038: error: implicit declaration of function 'pci_iounmap'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Cc: Jonas Bonn <jonas@southpole.se> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Grant Likely [Mon, 25 Jul 2011 15:49:43 +0000 (17:49 +0200)]
i2c: Allow i2c_add_numbered_adapter() to assign a bus id
Currently, if an i2c bus driver supports both static and dynamic bus
ids, it needs to choose between calling i2c_add_numbered_adapter() and
i2c_add_adapter(). This patch makes i2c_add_numbered_adapter()
redirect to i2c_add_adapter() if the requested bus id is -1.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Jean Delvare <khali@linux-fr.org>
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] s5pv210: make needlessly global symbols static
[CPUFREQ] exynos4210: make needlessly global symbols static
[CPUFREQ] S3C6410: Add some lower frequencies for 800MHz base clock operation
[CPUFREQ] S5PV210: Add reboot notifier to prevent system hang
[CPUFREQ] S5PV210: Adjust udelay prior to voltage scaling down
[CPUFREQ] S5PV210: Lock a mutex while changing the cpu frequency
[CPUFREQ] S5PV210: Add pm_notifier to prevent system unstable
[CPUFREQ] S5PV210: Add arm/int voltage control support
[CPUFREQ] S5PV210: Add additional symantics for "relation" in cpufreq with pm
[CPUFREQ] S3C64xx: Notify transition complete as soon as frequency changed
[CPUFREQ] S3C6410: Support 800MHz operation in cpufreq
[CPUFREQ] s5pv210-cpufreq.c: Add missing clk_put
[CPUFREQ] Move compile for S3C64XX cpufreq to /drivers/cpufreq
[CPUFREQ] Remove some vi noise that escaped into the Makefile.
[CPUFREQ] Move ARM Samsung cpufreq drivers to drivers/cpufreq/
[CPUFREQ/S3C64xx] Move S3C64xx CPUfreq driver into drivers/cpufreq
[CPUFREQ] Handle CPUs with different capabilities in acpi-cpufreq
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
bnx2x: use pci_pcie_cap()
bnx2x: fix bnx2x_stop_on_error flow in bnx2x_sp_rtnl_task
bnx2x: enable internal target-read for 57712 and up only
bnx2x: count statistic ramrods on EQ to prevent MC assert
bnx2x: fix loopback for non 10G link
bnx2x: dcb - send all unmapped priorities to same COS as L2
iwlwifi: Fix build with CONFIG_PM disabled.
gre: fix improper error handling
ipv4: use RT_TOS after some rt_tos conversions
via-velocity: remove duplicated #include
qlge: remove duplicated #include
igb: remove duplicated #include
can: c_can: remove duplicated #include
bnad: remove duplicated #include
net: allow netif_carrier to be called safely from IRQ
bna: Header File Consolidation
bna: HW Error Counter Fix
bna: Add HW Semaphore Unlock Logic
bna: IOC Event Name Change
bna: Mboxq Flush When IOC Disabled
...
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: PATA_ARASAN_CF depends on DMADEVICES
ata: remove unnecessary code
[libata] Prevent warning during PMP error recovery
ahci: RAID-mode SATA patch for Intel Panther Point DeviceIDs
pata_it821x: Fix RAID type display, by adding missing comma
sata_dwc_460ex: fix error path
ahci: Enable SB600 64bit DMA on Asus M3A
libata: report link resume failure as KERN_WARNING instead of ERR
ahci: move ahci_sb600_softreset to libahci.c and rename it
libata: leave port thawed after reset failure
ata: sata_via: Use dev_dbg
ata: Add and use ata_print_version_once
ata: Convert ata_<foo>_printk(KERN_<LEVEL> to ata_<foo>_<level>
ata: Convert dev_printk(KERN_<LEVEL> to dev_<level>(
bnx2x: count statistic ramrods on EQ to prevent MC assert
This patch includes:
- Counting statistics ramrods as EQ ramrods the way they should be. This
accounting is meant to prevent MC asserts in case of software bugs.
- Fixes in debug facilities which were added while working on one of such
bugs.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: dcb - send all unmapped priorities to same COS as L2
As a result of DCBX negotiation some priorities maybe untouched and still
unmapped to any COS; instead of sending them to COS0 we assign them
to the same COS as L2 traffic - to avoid collisions with storage class of
service.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
Current documentation referred to the old method of handling augmented
trees. Update documentation to correspond with the changes done in
commit b945d6b2554d ("rbtree: Undo augmented trees performance damage
and regression").
Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: David Woodhouse <David.Woodhouse@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Sasha Levin <levinsasha928@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lasse Collin [Sun, 24 Jul 2011 16:54:25 +0000 (19:54 +0300)]
XZ: Fix missing <linux/kernel.h> include
<linux/kernel.h> is needed for min_t. The old version
happened to work on x86 because <asm/unaligned.h>
indirectly includes <linux/kernel.h>, but it didn't
work on ARM.
<linux/kernel.h> includes <asm/byteorder.h> so it's
not necessary to include it explicitly anymore.
Al Viro [Sat, 23 Jul 2011 22:18:58 +0000 (18:18 -0400)]
fix jffs2 ACLs on big-endian with 16bit mode_t
casting int * to mode_t * is not a good thing - on a *lot* of big-endian
architectures mode_t happens to be smaller than int and there it breaks
quite spectaculary...
Fucked-up-by: commit cfc8dc6f6f69ede939e09c2af06a01adee577285 Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tim Chen [Tue, 19 Jul 2011 16:32:38 +0000 (09:32 -0700)]
VFS : mount lock scalability for internal mounts
For a number of file systems that don't have a mount point (e.g. sockfs
and pipefs), they are not marked as long term. Therefore in
mntput_no_expire, all locks in vfs_mount lock are taken instead of just
local cpu's lock to aggregate reference counts when we release
reference to file objects. In fact, only local lock need to have been
taken to update ref counts as these file systems are in no danger of
going away until we are ready to unregister them.
The attached patch marks file systems using kern_mount without
mount point as long term. The contentions of vfs_mount lock
is now eliminated. Before un-registering such file system,
kern_unmount should be called to remove the long term flag and
make the mount point ready to be freed.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The commit f02e8a6 sorts symbols placing each of them in its own elf section.
The sorting and merging into the canonical sections are done by the linker.
Unfortunately modpost to generate Module.symvers file parses vmlinux
(already linked) and all modules object files (which aren't linked yet).
These aren't sanitized by the linker yet. That breaks modpost that can't
detect license properly for modules. This patch makes modpost aware of
the new exported symbols structure.
Thanks to Arnaud Lacombe <lacombar@gmail.com> and Anders Kaseorg
<andersk@ksplice.com> for providing useful suggestions about code.
This work was supported by a hardware donation from the CE Linux Forum.
Reported-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Alessio Igor Bogani <abogani@kernel.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Kay Sievers [Sun, 24 Jul 2011 12:36:04 +0000 (22:06 +0930)]
module: add /sys/module/<name>/uevent files
Userspace wants to manage module parameters with udev rules.
This currently only works for loaded modules, but not for
built-in ones.
To allow access to the built-in modules we need to
re-trigger all module load events that happened before any
userspace was running. We already do the same thing for all
devices, subsystems(buses) and drivers.
This adds the currently missing /sys/module/<name>/uevent files
to all module entries.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (split & trivial fix)
Jonas Bonn [Thu, 30 Jun 2011 19:22:12 +0000 (21:22 +0200)]
modules: make arch's use default loader hooks
This patch removes all the module loader hook implementations in the
architecture specific code where the functionality is the same as that
now provided by the recently added default hooks.
Signed-off-by: Jonas Bonn <jonas@southpole.se> Acked-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Tested-by: Michal Simek <monstr@monstr.eu> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
projects / linux-beck.git / log