Linus Walleij [Wed, 18 May 2011 12:18:57 +0000 (14:18 +0200)]
dmaengine: move link order
Move the dmaengine subsystem up early in the drivers Makefile so
DMA is made available early to all drivers, just like e.g.
regulators. Now even regulators can use DMA on the same initlevel.
As a result we can bump the ste_dma40 and coh901318 dmaengine
drivers down one initlevel to subsys_init().
dmaengine/dw_dmac: implement pause and resume in dwc_control
Some peripherals like amba-pl011 needs pause to be implemented in DMA controller
drivers. This also returns correct status from dwc_tx_status() in case chan is
paused.
dmaengine/dw_dmac: Replace spin_lock* with irqsave variants and enable submission from callback
dmaengine routines can be called from interrupt context and with interrupts
disabled. Whereas spin_unlock_bh can't be called from such contexts. So this
patch converts all spin_*_bh routines to irqsave variants.
Also, spin_lock() used in tasklet is converted to irqsave variants, as tasklet
can be interrupted, and dma requests from such interruptions may also call
spin_lock.
Now, submission from callbacks are permitted as per dmaengine framework. So we
shouldn't hold any locks while calling callbacks. As locks were taken by parent
routines, so releasing them before calling callbacks doesn't look clean enough.
So, locks are taken inside all routine now, whereever they are required. And
dwc_descriptor_complete is always called without taking locks.
dmaengine/dw_dmac: Divide one sg to many desc, if sg len is greater than DWC_MAX_COUNT
If len passed in sg for slave_sg transfers is greater than DWC_MAX_COUNT, then
driver programmes controller incorrectly. This patch adds code to handle this
situation by allocation more than one desc for same sg.
dmaengine/dw_dmac: don't call callback routine in case dmaengine_terminate_all() is called
If dmaengine_terminate_all() is called for dma channel, then it doesn't make
much sense to call registered callback routine. While in case of success or
failure it must be called.
Nicolas Ferre [Mon, 9 May 2011 16:11:37 +0000 (18:11 +0200)]
dmaengine: at_hdmac: pause: no need to wait for FIFO empty
With the addition of the "pause" feature, an active wait was introduced
to check the "FIFO empty" event. This event was not always happening and
a timout contition was needed.
But, in some cases, this event depend on the peripheral connected to the
channel that is paused: FIFO becomes empty if the peripheral consumes data.
The timeout is pretty difficult to evaluate. Moreover, this check is not
needed.
In conclusion, it seems sensible to entirely remove the checking of
"FIFO empty" status when pausing.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[commit msg edited for grammer] Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Tomoya MORINAGA [Mon, 9 May 2011 07:09:39 +0000 (16:09 +0900)]
pch_dma: Support new device ML7223 IOH
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Tomoya MORINAGA [Mon, 9 May 2011 07:09:37 +0000 (16:09 +0900)]
pch_dma: Fix DMA setting issue
Currently, Direct-Start mode(*) is enabled.
Our IOH's devices must not use this mode.
This causes unexpected behavior.
This patch deletes Direct-Start setting.
(*) This mode is used in order for CPU to generate the DMA request.
Tomoya MORINAGA [Mon, 9 May 2011 07:09:35 +0000 (16:09 +0900)]
pch_dma: fix dma direction issue for ML7213 IOH video-in
Currently, even-channel number is set as tx direction and odd is set as rx.
However, though video-in uses ch6, the direction is not tx but rx.
This patch sets video-in's DMA direction correctly.
Nicolas Ferre [Sat, 30 Apr 2011 14:57:49 +0000 (16:57 +0200)]
dmaengine: at_hdmac: specialize AHB interfaces to optimize transfers
DMA controller has two AHB interfaces on the SOC internal
matrix.
It is more efficient to specialize each interface as the
access to memory can introduce latencies that are not compatible
with peripheral accesses requirements.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Nicolas Ferre [Sat, 30 Apr 2011 14:57:48 +0000 (16:57 +0200)]
dmaengine: at_hdmac: remove channel status testing in tasklet
There is no need to test if channel is enabled in tasklet:
- in error path, channel is disabled in interrupt routine
- in normal path, this test is performed in sub functions to report
a misuse of the engine.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Nicolas Ferre [Sat, 30 Apr 2011 14:57:45 +0000 (16:57 +0200)]
dmaengine: at_hdmac: modify way to use interrupts
Now we use Buffer Transfer Completed interrupts. If we
want a chained buffer completed information, we setup the
ATC_IEN bit in CTRLB register in the lli.
This is done by set_desc_eol() function and used by
memcpy/slave_sg functions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the correct api in probe to enable runtime pm for this driver.
Additionally, do not just call legacy suspend for runtime_suspend,
as this duplicates some work the pci core does for you.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Viresh Kumar [Thu, 24 Mar 2011 06:02:15 +0000 (11:32 +0530)]
dmaengine/dw_dmac fix: dwc_scan_descriptors must compare first desc address also with llp
dwc_scan_descriptors scans all descriptors from active_list in case transfer is
not completed. It compares first_desc->lli.llp, and then all childrens of its
tx_list. But it doesn't compare its own address, i.e. first_desc->txd.phys, as
this is what we have initially programmed into the controller register. So this
causes dma to stop and finish a transfer, which was never started. And thus
fail.
Linus Torvalds [Tue, 29 Mar 2011 19:09:30 +0000 (12:09 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
Linus Torvalds [Tue, 29 Mar 2011 18:43:30 +0000 (11:43 -0700)]
Merge branch 'frv' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-frv
* 'frv' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-frv:
FRV: Use generic show_interrupts()
FRV: Convert genirq namespace
frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
frv: Convert cpu irq_chip to new functions
frv: Convert mb93493 irq_chip to new functions
frv: Convert mb93093 irq_chip to new function
frv: Convert mb93091 irq_chip to new functions
frv: Fix typo from __do_IRQ overhaul
frv: Remove stale irq_chip.end
FRV: Do some cleanups
FRV: Missing node arg in alloc_thread_info_node() macro
NOMMU: implement access_remote_vm
NOMMU: support SMP dynamic percpu_alloc
NOMMU: percpu should use is_vmalloc_addr().
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: softdog.c: enhancement to optionally invoke panic instead of reboot on timer expiry
watchdog: fix nv_tco section mismatch
watchdog: sp5100_tco.c: Check if firmware has set correct value in tcobase.
watchdog: Convert release_resource to release_region/release_mem_region
watchdog: s3c2410_wdt.c: Convert release_resource to release_region/release_mem_region
Linus Torvalds [Tue, 29 Mar 2011 17:46:15 +0000 (10:46 -0700)]
Merge branch 'irq-final-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'irq-final-for-linus-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (111 commits)
gpio: ab8500: Mark broken
genirq: Remove move_*irq leftovers
genirq: Remove compat code
drivers: Final irq namespace conversion
mn10300: Use generic show_interrupts()
mn10300: Cleanup irq_desc access
mn10300: Convert genirq namespace
frv: Use generic show_interrupts()
frv: Convert genirq namespace
frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
frv: Convert cpu irq_chip to new functions
frv: Convert mb93493 irq_chip to new functions
frv: Convert mb93093 irq_chip to new function
frv: Convert mb93091 irq_chip to new functions
frv: Fix typo from __do_IRQ overhaul
frv: Remove stale irq_chip.end
m68k: Convert irq function namespace
xen: Use new irq_move functions
xen: Cleanup genirq namespace
unicore32: Use generic show_interrupts()
...
Peter Huewe [Tue, 29 Mar 2011 11:31:25 +0000 (13:31 +0200)]
char/tpm: Fix unitialized usage of data buffer
This patch fixes information leakage to the userspace by initializing
the data buffer to zero.
Reported-by: Peter Huewe <huewe.external@infineon.com> Signed-off-by: Peter Huewe <huewe.external@infineon.com> Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
[ Also removed the silly "* sizeof(u8)". If that isn't 1, we have way
deeper problems than a simple multiplication can fix. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Borislav Petkov [Tue, 29 Mar 2011 16:10:53 +0000 (18:10 +0200)]
amd64_edac: Fix potential memleak
We check the pointers together but at least one of them could be invalid
due to failed allocation. Since we cannot continue if either of the two
allocations has failed, exit early by freeing them both.
Dave Chinner [Tue, 29 Mar 2011 07:08:50 +0000 (18:08 +1100)]
fs: don't use igrab() while holding i_lock
Fix the incorrect use of igrab() inside the i_lock in NFS and Ceph‥
If we are already holding the i_lock, we have a reference to the
inode so we can safely use ihold() to gain an extra reference. This
avoids hangs due to lock recursion on the i_lock now that the
inode_lock is gone and igrab() uses the i_lock itself.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Cc: Ryan Mallon <ryan@bluewatersys.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
xfrm: Restrict extended sequence numbers to esp
xfrm: Check for esn buffer len in xfrm_new_ae
xfrm: Assign esn pointers when cloning a state
xfrm: Move the test on replay window size into the replay check functions
netdev: bfin_mac: document TE setting in RMII modes
drivers net: Fix declaration ordering in inline functions.
cxgb3: Apply interrupt coalescing settings to all queues
net: Always allocate at least 16 skb frags regardless of page size
ipv4: Don't ip_rt_put() an error pointer in RAW sockets.
net: fix ethtool->set_flags not intended -EINVAL return value
mlx4_en: Fix loss of promiscuity
tg3: Fix inline keyword usage
tg3: use <linux/io.h> and <linux/uaccess.h> instead <asm/io.h> and <asm/uaccess.h>
net: use CHECKSUM_NONE instead of magic number
Net / jme: Do not use legacy PCI power management
myri10ge: small rx_done refactoring
bridge: notify applications if address of bridge device changes
ipv4: Fix IP timestamp option (IPOPT_TS_PRESPEC) handling in ip_options_echo()
can: c_can: Fix tx_bytes accounting
can: c_can_platform: fix irq check in probe
...
Thomas Gleixner [Thu, 24 Mar 2011 20:37:31 +0000 (21:37 +0100)]
xen: Use new irq_move functions
These functions take irq_data as an argument and avoid a redundant
lookup in the sparse irq case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Thomas Gleixner [Fri, 25 Mar 2011 10:01:39 +0000 (11:01 +0100)]
xen: Convert genirq namespace
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Randy Dunlap [Thu, 24 Mar 2011 20:34:32 +0000 (13:34 -0700)]
xen: fix p2m section mismatches
Fix section mismatch warnings:
set_phys_range_identity() is called by __init xen_set_identity(),
so also mark set_phys_range_identity() as __init.
then:
__early_alloc_p2m() is called set_phys_range_identity(), so also mark
__early_alloc_p2m() as __init.
WARNING: arch/x86/built-in.o(.text+0x7856): Section mismatch in reference from the function __early_alloc_p2m() to the function .init.text:extend_brk()
The function __early_alloc_p2m() references
the function __init extend_brk().
This is often because __early_alloc_p2m lacks a __init
annotation or the annotation of extend_brk is wrong.
WARNING: arch/x86/built-in.o(.text+0x7967): Section mismatch in reference from the function set_phys_range_identity() to the function .init.text:extend_brk()
The function set_phys_range_identity() references
the function __init extend_brk().
This is often because set_phys_range_identity lacks a __init
annotation or the annotation of extend_brk is wrong.
[v2: Per Stephen Hemming recommonedation made __early_alloc_p2m static] Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
David Howells [Tue, 29 Mar 2011 13:05:12 +0000 (14:05 +0100)]
FRV: Missing node arg in alloc_thread_info_node() macro
There are two alloc_thread_info_node() macros defined (one for debugging and
one for normal). The commit that changed them most recently:
commit b6a84016bd2598e35ead635147fa53619982648d
Author: Eric Dumazet <eric.dumazet@gmail.com>
Date: Tue Mar 22 16:30:42 2011 -0700
Subject: mm: NUMA aware alloc_thread_info_node()
didn't add the node argument into the macro argument list for the normal macro.
This results in the following error:
kernel/fork.c:267:39: error: macro "alloc_thread_info_node" passed 2 arguments, but takes just 1
kernel/fork.c: In function 'dup_task_struct':
kernel/fork.c:267: error: 'alloc_thread_info_node' undeclared (first use in this function)
kernel/fork.c:267: error: (Each undeclared identifier is reported only once
kernel/fork.c:267: error: for each function it appears in.)
Signed-off-by: David Howells <dhowells@redhat.com>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:39 +0000 (20:20 +0100)]
frv: Select GENERIC_HARDIRQS_NO_DEPRECATED
All chips converted
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.601290592@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:38 +0000 (20:20 +0100)]
frv: Convert cpu irq_chip to new functions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.501651128@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:37 +0000 (20:20 +0100)]
frv: Convert mb93493 irq_chip to new functions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.401266547@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:36 +0000 (20:20 +0100)]
frv: Convert mb93093 irq_chip to new function
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.300303769@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:35 +0000 (20:20 +0100)]
frv: Convert mb93091 irq_chip to new functions
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.203431646@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:34 +0000 (20:20 +0100)]
frv: Fix typo from __do_IRQ overhaul
Compiles way better.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.109992056@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sun, 6 Feb 2011 19:20:33 +0000 (20:20 +0100)]
frv: Remove stale irq_chip.end
irq_chip.end got obsolete with the removal of __do_IRQ().
irq-mb93093.c even lacks an implementation, but nobody noticed that
it's broken since commit 88d6e1 in 2006.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: David Howells <dhowells@redhat.com>
LKML-Reference: <20110206192106.011224503@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 24 Mar 2011 20:31:25 +0000 (21:31 +0100)]
xen: Use new irq_move functions
These functions take irq_data as an argument and avoid a redundant
lookup in the sparse irq case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Thomas Gleixner [Thu, 24 Mar 2011 08:03:45 +0000 (09:03 +0100)]
sparc: Use the new genirq functionality
Make use of the new features in genirq:
1) Set the chip flag IRCHIP_EOI_IF_HANDLED, which ensures in the
core code that irq_eoi() is only called when the interrupt was
handled. That removes the extra status check in the callback.
2) Use the preflow handler, which is called from the fasteoi core code
before the device handler. That avoids another status check and the
open coded handler redirection.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: sparclinux@vger.kernel.org
Thomas Gleixner [Fri, 25 Mar 2011 15:26:01 +0000 (16:26 +0100)]
powerpc: xilinx: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The core also
updates the LEVEL flag.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:23:57 +0000 (16:23 +0100)]
powerpc: uic: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The core also
updates IRQ_LEVEL.
Use irq_data to get the level type information in the chip functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:20:15 +0000 (16:20 +0100)]
powerpc: mpic: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Retrieve the IRQ_LEVEL information from irq_data which avoids a
redundant sparse irq lookup as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:18:32 +0000 (16:18 +0100)]
powerpc: mpc8xx_pic: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus. The level flag is
updated in the core as well.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:16:30 +0000 (16:16 +0100)]
powerpc: ipic: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:07:51 +0000 (16:07 +0100)]
powerpc: cpm2_pic: Cleanup flow type handling
The core irq_set_type() function updates the flow type when the chip
callback returns 0. So setting the type is bogus.
The new core code allows to update the type in irq_data and return
IRQ_SET_MASK_OK_NOCOPY, so the core code will not touch it, except for
setting the IRQ_LEVEL flag.
Use the proper accessors for setting the irq handlers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 25 Mar 2011 15:04:41 +0000 (16:04 +0100)]
powerpc: cell: Fix the irq_desc access
The core irq_set_type() function updates the flow type when the chip
callback returns 0. It also updates irq_data, so this can be used in
irq_ack() to check for the level bit. That avoids a redundant sparse
irq lookup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
projects / linux-beck.git / log