David Daney [Wed, 19 Jun 2013 20:37:27 +0000 (20:37 +0000)]
tty/8250_dw: Add support for OCTEON UARTS.
A few differences needed by OCTEON:
o These are DWC UARTS, but have USR at a different offset.
o Internal SoC buses require reading back from registers to maintain
write ordering.
o 8250 on OCTEON appears with 64-bit wide registers, so when using
readb/writeb in big endian mode we have to adjust the membase to hit
the proper part of the register.
o No UCV register, so we hard code some properties.
Because OCTEON doesn't have a UCV register, I change where
dw8250_setup_port(), which reads the UCV, is called by pushing it in
to the OF and ACPI probe functions, and move unchanged
dw8250_setup_port() earlier in the file.
David Daney [Wed, 19 Jun 2013 20:37:26 +0000 (20:37 +0000)]
MIPS: OCTEON: Set proper UART clock in internal device trees.
Following patch to use generic 8250 drivers will need proper clock
information. So when using the internal device tree, populate the
"clock-frequency" property with the correct value.
Florian Fainelli [Tue, 18 Jun 2013 16:55:43 +0000 (16:55 +0000)]
MIPS: BCM63XX: let board specify an external GPIO to reset PHY
Some boards may need to reset their external PHY or switch they are
attached to, add a hook for doing this along with providing custom
linux/gpio.h flags for doing this.
Florian Fainelli [Tue, 18 Jun 2013 16:55:42 +0000 (16:55 +0000)]
MIPS: BCM63XX: provide a MAC address for BCM3368 chips
The BCM3368 SoC uses a NVRAM format which is not compatible with the one
used by CFE, provide a default MAC address which is suitable for use and
which is the default one also being used by the bootloader on these
chips.
Florian Fainelli [Tue, 18 Jun 2013 16:55:41 +0000 (16:55 +0000)]
MIPS: BCM63XX: recognize Cable Modem firmware format
Add the firmware header format which is used by Broadcom Cable Modem
SoCs such as the BCM3368 SoC. We export the bcm_hcs firmware format
structure because it is used by user-land tools to create firmware
images for these SoCs and will later be used by a corresponding MTD
parser.
Florian Fainelli [Tue, 18 Jun 2013 16:55:40 +0000 (16:55 +0000)]
MIPS: BCM63XX: add support for BCM3368 Cable Modem
The Broadcom BCM3368 Cable Modem SoC is extremely similar to the
existing BCM63xx DSL SoCs, in particular BCM6358, therefore little effort
in the existing code base is required to get it supported. This patch adds
support for the following on-chip peripherals:
- two UARTS
- GPIO
- Ethernet
- SPI
- PCI
- NOR Flash
The most noticeable difference with 3368 is that it has its peripheral
register at 0xfff8_0000 we check that separately in ioremap.h. Since
3368 is identical to 6358 for its clock and reset bits, we use them
verbatim.
Florian Fainelli [Tue, 18 Jun 2013 16:55:39 +0000 (16:55 +0000)]
MIPS: BCM63XX: select BOOT_RAW
Enabling BOOT_RAW is mandatory to get a binary image (objcopy from ELF
to binary) to work. This does not affect the ELF kernels which are used
by CFE on BCM63XX DSL platforms, but is going to be necessary to support
BCM63XX on Cable Modem chips such as BCM3368.
Paul Gortmaker [Tue, 18 Jun 2013 17:01:10 +0000 (17:01 +0000)]
MIPS: Delete Wind River ppmc eval board support.
This board has been EOL for many years now; lets not burden people doing
build coverage and other tree wide work with working on essentially dead
files.
[ralf@linux-mips.org: Also remove arch/mips/include/asm/mach-wrppmc/war.h.]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: linux-mips@linux-mips.org Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Patchwork: http://patchwork.linux-mips.org/patch/5503/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Jonas Gorski [Sat, 15 Jun 2013 10:12:46 +0000 (10:12 +0000)]
MIPS: remove alloc_pci_controller prototype
Commit 610019baddcb4c4c323c12cd44ca7f73d7145d6f ("[MIPS] Remove unused
function alloc_pci_controller.") removed the function, but left the
prototype in the header file.
Remove it as well so people don't get tempted to use it and wonder why
it doesn't work.
Jonas Gorski [Mon, 3 Jun 2013 14:39:35 +0000 (14:39 +0000)]
MIPS: BCM63XX: select BMIPS4350 and default to 2 CPUs for supported SoCs
All BCM63XX SoCs starting with BCM6358 have a BMIPS4350 instead of a
BMIPS3300, so select it unless support for any of the older SoCs is
selected.
All BMIPS4350 have only two CPUs, so select the appropriate default.
Signed-off-by: Jonas Gorski <jogo@openwrt.org> Cc: linux-mips@linux-mips.org Cc: John Crispin <blogic@openwrt.org> Cc: Maxime Bizon <mbizon@freebox.fr> Cc: Florian Fainelli <florian@openwrt.org> Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/5355/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Gregory Fong [Mon, 17 Jun 2013 19:36:07 +0000 (19:36 +0000)]
MIPS: r4k,octeon,r2300: stack protector: change canary per task
For non-SMP, uses the new random canary value that is stored in the
task struct whenever a new task is forked. Based on ARM version in df0698be14c6683606d5df2d83e3ae40f85ed0d9 and subject to the same
limitations: the variable GCC expects, __stack_chk_guard, is global,
so this will not work on SMP.
Quoting Nicolas Pitre <nico@fluxnic.net>: "One way to overcome this
GCC limitation would be to locate the __stack_chk_guard variable into
a memory page of its own for each CPU, and then use TLB locking to
have each CPU see its own page at the same virtual address for each of
them."
Gregory Fong [Wed, 12 Jun 2013 17:08:54 +0000 (17:08 +0000)]
MIPS: initial stack protector support
Implements basic stack protector support based on ARM version in c743f38013aeff58ef6252601e397b5ba281c633 , with Kconfig option,
constant canary value set at boot time, and script to check if
compiler actually supports stack protector.
Tested by creating a kernel module that writes past end of char[].
Paul Bolle [Thu, 30 May 2013 09:51:21 +0000 (09:51 +0000)]
MIPS: MSP71xx: Remove gpio drivers
The PMC MSP71XX gpio drivers were added in v2.6.28, see commit 9fa32c6b02 ("MIPS: PMC MSP71XX gpio drivers"). They are only built if
CONFIG_HAVE_GPIO_LIB is set.
But the Kconfig symbol HAVE_GPIO_LIB was already removed in v2.6.27, see
commit 7444a72eff ("gpiolib: allow user-selection"). So these drivers
were never buildable. Perhaps no-one noticed because there are no in
tree users of msp71xx_init_gpio() and msp71xx_init_gpio_extended().
Anyhow, these drivers can safely be removed.
Jayachandran C [Tue, 11 Jun 2013 14:41:36 +0000 (14:41 +0000)]
MIPS: Fixup check for invalid scratch register
The invalid value for scratch register is -1, so update the checks of
the form (scratch_reg > 0) to be (scratch_reg >= 0). This will fix
the case in Netlogic XLP where the scratch_reg can be 0.
Jayachandran C [Tue, 11 Jun 2013 14:41:35 +0000 (14:41 +0000)]
MIPS: Allow platform specific scratch registers
XLR/XLP COP0 scratch is register 22, sel 0-7. Add a function
c0_kscratch() which returns the scratch register for the platform,
and use the return value while generating TLB handlers.
Setup kscratch_mask to 0xf for XLR/XLP since the config4 register
does not exist. This allows the kernel to allocate scratch registers
0-3 if needed.
Jayachandran C [Mon, 10 Jun 2013 06:41:10 +0000 (06:41 +0000)]
MIPS: Netlogic: Fix plat_irq_dispatch
Fix an issue in plat_irq_dispatch due to which it can call do_IRQ
with a PIC irq that is not mapped.
When a per-cpu interrupt and a PIC interrupt are both active, the
check 'eirr & PERCPU_IRQ_MASK' will be true, but the interrupt in 'i'
will be the number of the PIC interrupt. In this case, we will call
do_IRQ on the PIC interrupt without mapping it with nlm_irq_to_xirq().
Fix this by using __ffs64 instead of __ilog2_u64 and using the
interrupt number instead of mask to identify per-cpu interrupts.
Jayachandran C [Mon, 10 Jun 2013 06:41:08 +0000 (06:41 +0000)]
MIPS: Netlogic: Fixup memory regions for prefetch
Fix a cache error found in stress test, caused by the prefetch instruction
going beyond valid memory when acessing the last page of a region. Add
the pref_backup logic similar to XLR in XLP too.
Jayachandran C [Mon, 10 Jun 2013 06:41:07 +0000 (06:41 +0000)]
MIPS: Netlogic: wait for all hardware threads
Earlier we just waited for the first thread of the CPU to come online
before proceeding to wake up others. Update it to wait for all the CPUs
in the core. This will be useful when the boot-up is slow, like while
debugging or when running in a simulator.
Jayachandran C [Mon, 10 Jun 2013 06:41:01 +0000 (06:41 +0000)]
MIPS: Netlogic: Split reset code out of smpboot.S
The reset and core initialization code should be available for
uniprocessor as well. This changes is just to take out the code
into a different file, without any change to the logic.
The change for uniprocessor initialization code is in a later patch.
Jayachandran C [Mon, 10 Jun 2013 06:33:25 +0000 (06:33 +0000)]
MIPS: boot: Fixes for compressed/uart-16550.c
Fix uart-16550.c for adding XLR/XLP support, changes are:
* Make register read/write use volatile pointers
* Support 32 bit IO read/write
* Increase timeout in waiting for UART LSR
Jayachandran C [Mon, 10 Jun 2013 06:30:04 +0000 (06:30 +0000)]
MIPS: Netlogic: COP2 save/restore code
Add COP2 register state structure and functions for Netlogic XLP. The
RX and TX buffers and status registers are to be saved. Since the
registers are 64-bit, do the implementation in inline assembly which
works on both 32-bit and 64-bit kernels.
Jayachandran C [Mon, 10 Jun 2013 06:30:03 +0000 (06:30 +0000)]
MIPS: Netlogic: rename nlm_cop2_save/restore
Rename macro nlm_cop2_enable() to nlm_cop2_enable_irqsave() and the macro
nlm_cop2_restore to nlm_cop2_disable_irqrestore(). The new names will
reflect the functionality better, and will make nlm_cop2_restore()
available to be used later in COP2 save/restore patch.
The sel argument os nlm_read_c2_status() was not used and the macro
returned the sel 0 in all cases. Fix this by defining two macros:
nlm_read_c2_status0() and nlm_read_c2_status1() to return the two
status registers.
Add functions to write to the status registers as well.
Jayachandran C [Mon, 10 Jun 2013 06:30:01 +0000 (06:30 +0000)]
MIPS: Allow kernel to use coprocessor 2
Kernel threads should be able to use COP2 if the platform needs it.
Do not call die_if_kernel() for a coprocessor unusable exception if
the exception due to COP2 usage. Instead, the default notifier for
COP2 exceptions is updated to call die_if_kernel.
Jayachandran C [Mon, 10 Jun 2013 06:30:00 +0000 (06:30 +0000)]
MIPS: Move cop2 save/restore to switch_to()
Move the common code for saving and restoring platform specific COP2
registers to switch_to(). This will make supporting new platforms (like
Netlogic XLP) easier.
The platform specific COP2 definitions are to be specified in
asm/processor.h and in asm/cop2.h.
Add SWIOTLB config option and related files to Netlogic platform.
Some XLP SoC components like the SD/MMC interface cannot do DMA beyond
32-bit physical address. The SD/MMC driver can use memory outside this
range for IO, to support this we have to add bounce buffers implemented
by SWIOTLB.
Jayachandran C [Mon, 10 Jun 2013 06:28:08 +0000 (06:28 +0000)]
MIPS: Support SWIOTLB in default dma operations
Provide a default implementation of phys_to_dma and dma_to_phys in
mach-generic/dma_coherence.h.
If CONFIG_NEED_SG_DMA_LENGTH is defined, the dma_length field in
struct scatterlist is used. Set this up in mips_dma_map_sg so that
the default mips DMA ops can be used when SWIOTLB is enabled.
Linus Torvalds [Sat, 8 Jun 2013 22:51:21 +0000 (15:51 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
- Trivial: unused variable removal
- Posix-timers: Add the clock ID to the new proc interface to make it
useful. The interface is new and should be functional when we reach
the final 3.10 release.
- Cure a false positive warning in the tick code introduced by the
overhaul in 3.10
- Fix for a persistent clock detection regression introduced in this
cycle
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Correct run-time detection of persistent_clock.
ntp: Remove unused variable flags in __hardpps
posix-timers: Show clock ID in proc file
tick: Cure broadcast false positive pending bit warning
Linus Torvalds [Sat, 8 Jun 2013 22:50:42 +0000 (15:50 -0700)]
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux
Pull irqdomain bug fixes from Grant Likely:
"This branch contains a set of straight forward bug fixes to the
irqdomain code and to a couple of drivers that make use of it."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux:
irqchip: Return -EPERM for reserved IRQs
irqdomain: document the simple domain first_irq
kernel/irq/irqdomain.c: before use 'irq_data', need check it whether valid.
irqdomain: export irq_domain_add_simple
Grant Likely [Thu, 6 Jun 2013 13:11:38 +0000 (14:11 +0100)]
irqchip: Return -EPERM for reserved IRQs
The irqdomain core will report a log message for any attempted map call
that fails unless the error code is -EPERM. This patch changes the
Versatile irq controller drivers to use -EPERM because it is normal for
a subset of the IRQ inputs to be marked as reserved on the various
Versatile platforms.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Linus Walleij [Thu, 6 Jun 2013 11:10:23 +0000 (12:10 +0100)]
irqdomain: document the simple domain first_irq
The first_irq needs to be zero to get a linear domain and that
comes with special semantics. We want to simplify this going
forward but some documentation never hurts.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Grant Likely <grant.likely@linaro.org>
All other irq_domain_add_* functions are exported already, and apparently
this one got left out by mistake, which causes build errors for ARM
allmodconfig kernels:
Linus Torvalds [Sat, 8 Jun 2013 18:56:22 +0000 (11:56 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes for arm-soc platforms.
Nothing controversial here, a handful of fixes for regressions and/or
serious problems across several of the platforms. Things are slowing
down nicely on fix rates for 3.10"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: exynos: add debug_ll_io_init() call in exynos_init_io()
ARM: EXYNOS: uncompress - print debug messages if DEBUG_LL is defined
ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
sh-pfc: r8a7779: Don't group USB OVC and PENC pins
ARM: mxs: icoll: Fix interrupts gpio bank 0
ARM: imx: clk-imx6q: AXI clock select index is incorrect
ARM: bcm2835: override the HW UART periphid
ARM: mvebu: Fix bug in coherency fabric low level init function
ARM: Kirkwood: TS219: Fix crash by double PCIe instantiation
ARM: ux500: Provide supplies for AUX1, AUX2 and AUX3
ARM: ux500: Only configure wake-up reasons on ux500 based platforms
ARM: dts: imx: fix clocks for cspi
ARM i.MX6q: fix for ldb_di_sels
Linus Torvalds [Sat, 8 Jun 2013 18:51:13 +0000 (11:51 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"MIPS fixes across the field. The only area that's standing out is the
exception handling which received it's dose of breakage as part of the
microMIPS patchset"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ralink: add missing SZ_1M multiplier
MIPS: Compat: Fix cputime_to_timeval() arguments in compat binfmt_elf.
MIPS: OCTEON: Improve _machine_halt implementation.
MIPS: rtlx: Fix implicit declaration of function set_vi_handler()
MIPS: Trap exception handling fixes
MIPS: Quit exposing Kconfig symbols in uapi headers.
MIPS: Remove duplicate definition of check_for_high_segbits.
Linus Torvalds [Sat, 8 Jun 2013 18:35:20 +0000 (11:35 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Regression fixers for the big 3:
- nouveau: hdmi audio, dac load detect, s/r regressions fixed
- radeon: long standing system hang fixed, hdmi audio and rs780 fast
fb fixes
- intel: one old regression, a WARN removal, and a stop X dying fix
Otherwise one mgag200 fix, a couple of arm build fixes, and a core use
after free fix."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nv50/kms: use dac loadval from vbios, where it's available
drm/nv50/disp: force dac power state during load detect
drm/nv50-nv84/fifo: fix resume regression introduced by playlist race fix
drm/nv84/disp: Fix HDMI audio regression
drm/i915/sdvo: Use &intel_sdvo->ddc instead of intel_sdvo->i2c for DDC.
drm/radeon: don't allow audio on DCE6
drm/radeon: Use direct mapping for fast fb access on RS780/RS880 (v2)
radeon: Fix system hang issue when using KMS with older cards
drm/i915: no lvds quirk for hp t5740
drm/i915: Quirk the pipe A quirk in the modeset state checker
drm/i915: Fix spurious -EIO/SIGBUS on wedged gpus
drm/mgag200: Add missing write to index before accessing data register
drm/nouveau: use mdelay instead of large udelay constants
drm/tilcd: select BACKLIGHT_LCD_SUPPORT
drm: fix a use-after-free when GPU acceleration disabled
Linus Torvalds [Sat, 8 Jun 2013 17:05:10 +0000 (10:05 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Fix from Andy is for dmatest regression reported by Will and Rabin has
fixed runtime ref counting for st_dma40"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmatest: do not allow to interrupt ongoing tests
dmaengine: ste_dma40: fix pm runtime ref counting
Linus Torvalds [Sat, 8 Jun 2013 01:46:51 +0000 (18:46 -0700)]
Merge tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This contains 4 fixes.
The first two fix the case where full RCU debugging is enabled,
enabling function tracing causes a live lock of the system. This is
due to the added debug checks in rcu_dereference_raw() that is used by
the function tracer. These checks are also traced by the function
tracer as well as cause enough overhead to the function tracer to slow
down the system enough that the time to finish an interrupt can take
longer than when the next interrupt is triggered, causing a live lock
from the timer interrupt.
Talking this over with Paul McKenney, we came up with a fix that adds
a new rcu_dereference_raw_notrace() that does not perform these added
checks, and let the function tracer use that.
The third commit fixes a failed compile when branch tracing is
enabled, due to the conversion of the trace_test_buffer() selftest
that the branch trace wasn't converted for.
The forth patch fixes a bug caught by the RCU lockdep code where a
rcu_read_lock() is performed when rcu is disabled (either going to or
from idle, or user space). This happened on the irqsoff tracer as it
calls task_uid(). The fix here was to use current_uid() when possible
that doesn't use rcu locking. Which luckily, is always used when
irqsoff calls this code."
* tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Use current_uid() for critical time tracing
tracing: Fix bad parameter passed in branch selftest
ftrace: Use the rcu _notrace variants for rcu_dereference_raw() and friends
rcu: Add _notrace variation of rcu_dereference_raw() and hlist_for_each_entry_rcu()
Revert "ACPI / scan: do not match drivers against objects having scan handlers"
Commit 9f29ab11ddbf ("ACPI / scan: do not match drivers against objects
having scan handlers") introduced a boot regression on Tony's ia64 HP
rx2600. Tony says:
"It panics with the message:
Kernel panic - not syncing: Unable to find SBA IOMMU: Try a generic or DIG kernel
[...] my problem comes from arch/ia64/hp/common/sba_iommu.c
where the code in sba_init() says:
acpi_bus_register_driver(&acpi_sba_ioc_driver);
if (!ioc_list) {
but because of this change we never managed to call ioc_init()
so ioc_list doesn't get set up, and we die."
Revert it to avoid this breakage and we'll fix the problem it attempted
to address later.
Reported-by: Tony Luck <tony.luck@gmail.com> Cc: 3.9+ <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olof Johansson [Sat, 8 Jun 2013 01:19:30 +0000 (18:19 -0700)]
Merge tag 'mxs-fixes-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo, mxs fixes for 3.10:
- Since the time we move to MULTI_IRQ_HANDLER, the 0x7f polling for no
interrupt in icoll_handle_irq() becomes insane, because 0x7f is an
valid interrupt number, the irq of gpio bank 0. That unnecessary
polling results in the driver not detecting when irq 0x7f is active
which makes the machine effectively dead lock. The fix removes the
interrupt poll loop and allows usage of gpio0 interrupt without an
infinite loop.
* tag 'mxs-fixes-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: icoll: Fix interrupts gpio bank 0
Olof Johansson [Sat, 8 Jun 2013 01:18:08 +0000 (18:18 -0700)]
Merge tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo, imx fixes for 3.10, take 2:
- One device tree fix for all spi node to have per clock added.
The clock is needed by spi driver to calculate bit rate divisor.
The spi node in the current device trees either does not have the
clock or is defined as dummy clock, in which case the driver probe
will fail or spi will run at a wrong bit rate.
- Two imx6q clock fixes, which correct axi_sels and ldb_di_sels.
* tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: clk-imx6q: AXI clock select index is incorrect
ARM: dts: imx: fix clocks for cspi
ARM i.MX6q: fix for ldb_di_sels
Doug Anderson [Wed, 5 Jun 2013 20:56:33 +0000 (13:56 -0700)]
ARM: exynos: add debug_ll_io_init() call in exynos_init_io()
If the early MMU mapping of the UART happens to get booted out of the
TLB between the start of paging_init() and when we finally re-add the
UART at the very end of s3c_init_cpu(), we'll get a hang at bootup if
we've got early_printk enabled. Avoid this hang by calling
debug_ll_io_init() early.
Without this patch, you can reliably reproduce a hang when early
printk is enabled by adding flush_tlb_all() at the start of
exynos_init_io(). After this patch the hang goes away.
Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 8 Jun 2013 01:10:42 +0000 (18:10 -0700)]
Merge tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman, Renesas ARM based SoC fixes for v3.10:
- Correction to USB OVC and PENC pin groupings on r8a7779 SoC.
This avoids conflicts when the USB_OVCn pins are used by another function.
This has been observed to be a problem in v3.10-rc1.
- Update CMT clock rating for sh73a0 SoC to resolve boot failure
on kzm9g-reference. This resolves a regression between v3.9 and v3.10-rc1.
* tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
sh-pfc: r8a7779: Don't group USB OVC and PENC pins
Tushar Behera [Tue, 4 Jun 2013 04:19:10 +0000 (09:49 +0530)]
ARM: EXYNOS: uncompress - print debug messages if DEBUG_LL is defined
Printing low-level debug messages make an assumption that the specified
UART port has been preconfigured by the bootloader. Incorrectly
specified UART port results in system getting stalled while printing the
message "Uncompressing Linux... done, booting the kernel"
This UART port number is specified through S3C_LOWLEVEL_UART_PORT. Since
the UART port might different for different board, it is not possible to
specify it correctly for every board that use a common defconfig file.
Calling this print subroutine only when DEBUG_LL fixes the problem. By
disabling DEBUG_LL in default config file, we would be able to boot
multiple boards with different default UART ports.
With this current approach, we miss the print "Uncompressing Linux...
done, booting the kernel." when DEBUG_LL is not defined.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Fri, 7 Jun 2013 23:21:44 +0000 (16:21 -0700)]
Merge tag 'ecryptfs-3.10-rc5-msync' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
- Fixes how eCryptfs handles msync to sync both the upper and lower
file
- A couple of MAINTAINERS updates
* tag 'ecryptfs-3.10-rc5-msync' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: Check return of filemap_write_and_wait during fsync
Update eCryptFS maintainers
ecryptfs: fixed msync to flush data
Linus Torvalds [Fri, 7 Jun 2013 23:05:43 +0000 (16:05 -0700)]
Merge branch 'for-3.10' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fix from Steve French:
"Fix one byte buffer overrun with prefixpaths on cifs mounts which can
cause a problem with mount depending on the string length"
* 'for-3.10' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix off-by-one bug in build_unc_path_to_root
Andy Shevchenko [Thu, 23 May 2013 11:29:53 +0000 (14:29 +0300)]
dmatest: do not allow to interrupt ongoing tests
When user interrupts ongoing transfers the dmatest may end up with console
lockup, oops, or data mismatch. This patch prevents user to abort any ongoing
test.
Documentation is updated accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reported-by: Will Deacon <will.deacon@arm.com> Tested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Linus Torvalds [Fri, 7 Jun 2013 20:05:18 +0000 (13:05 -0700)]
Merge tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- A pile of small regression fix patches for HD-audio VIA codecs
- Quirks for HD-aduio and USB-audio devices
- A trivial SIS7019 error path fix
* tag 'sound-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio - Fix invalid volume resolution on Logitech HD webcam c270
ALSA: usb-audio - Apply Logitech QuickCam Pro 9000 quirk only to audio iface
ALSA: hda/via - Clean up duplicated codes
ALSA: hda/via - Fix wrongly cleared pins after suspend on VT1802
ALSA: hda - Add keep_eapd_on flag to generic parser
ALSA: hda - Allow setting automute/automic hooks after parsing
ALSA: hda/via - Disable broken dynamic power control
ALSA: usb-audio: fix Roland/Cakewalk UM-3G support
ALSA: hda - Add headset quirk for two Dell machines
ALSA: hda - add dock support for Thinkpad T431s
ALSA: sis7019: fix error return code in sis_chip_create()
Linus Torvalds [Fri, 7 Jun 2013 20:03:53 +0000 (13:03 -0700)]
Merge tag 'pm+acpi-3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael J Wysocki:
- Fix for an ACPI PM regression causing Toshiba P870-303 to crash
during boot from Rafael J Wysocki.
- ACPI fix for an issue causing some drivers to attempt to bind to
devices they shouldn't touch from Aaron Lu.
- Fix for a recent cpufreq regression related to a possible race with
CPU offline from Michael Wang.
- ACPI cpufreq regression fix for an issue causing turbo frequencies to
be underutilized in some cases from Ross Lagerwall.
- cpufreq-cpu0 driver fix related to incorrect clock ACPI usage from
Guennadi Liakhovetski.
- HP WMI driver fix for an issue causing GPS initialization and
poweroff failures on HP Elitebook 6930p from Lan Tianyu.
- APEI (ACPI Platform Error Interface) fix for an issue in the error
code path in ghes_probe() from Wei Yongjun.
- New ACPI video driver blacklist entries for HP m4 and HP Pavilion g6
from Alex Hung and Ash Willis.
* tag 'pm+acpi-3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Do not execute _PS0 for devices without _PSC during initialization
cpufreq: cpufreq-cpu0: use the exact frequency for clk_set_rate()
cpufreq: protect 'policy->cpus' from offlining during __gov_queue_work()
ACPI / scan: do not match drivers against objects having scan handlers
ACPI / APEI: fix error return code in ghes_probe()
acpi-cpufreq: set current frequency based on target P-State
ACPI / video: ignore BIOS initial backlight value for HP Pavilion g6
ACPI / video: ignore BIOS initial backlight value for HP m4
x86 / platform / hp_wmi: Fix bluetooth_rfkill misuse in hp_wmi_rfkill_setup()
* pm-fixes:
cpufreq: cpufreq-cpu0: use the exact frequency for clk_set_rate()
cpufreq: protect 'policy->cpus' from offlining during __gov_queue_work()
acpi-cpufreq: set current frequency based on target P-State
* acpi-fixes:
ACPI / PM: Do not execute _PS0 for devices without _PSC during initialization
ACPI / scan: do not match drivers against objects having scan handlers
ACPI / APEI: fix error return code in ghes_probe()
ACPI / video: ignore BIOS initial backlight value for HP Pavilion g6
ACPI / video: ignore BIOS initial backlight value for HP m4
x86 / platform / hp_wmi: Fix bluetooth_rfkill misuse in hp_wmi_rfkill_setup()
ACPI / PM: Do not execute _PS0 for devices without _PSC during initialization
Commit b378549 (ACPI / PM: Do not power manage devices in unknown
initial states) added code to force devices without _PSC, but having
_PS0 defined in the ACPI namespace, into ACPI power state D0 by
executing _PS0 for them. That turned out to break Toshiba P870-303,
however, so revert that code.
References: https://bugzilla.kernel.org/show_bug.cgi?id=58201 Reported-and-tested-by: Jerome Cantenot <jerome.cantenot@gmail.com> Tracked-down-by: Lan Tianyu <tianyu.lan@intel.com> Cc: 3.9+ <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull networking fix from David Miller:
"This is a quick one commit pull request to cure the regression
introduced by the MSG_CMSG_COMPAT change."
(Background: commit 1be374a0518a completely broke 32-bit COMPAT handling
by not only disallowing MSG_CMSG_COMPAT from user APIs, but clearing it
in our own internal use too!)
Linus Torvalds [Thu, 6 Jun 2013 23:34:11 +0000 (16:34 -0700)]
Merge tag 'staging-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg Kroah-Hartman:
"Here are some staging and IIO driver fixes for the 3.10-rc5 release.
All of them are tiny, and fix a number of reported issues (build and
runtime)"
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'staging-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio:inkern: Fix typo/bug in convert raw to processed.
iio: frequency: ad4350: Fix bug / typo in mask
inkern: iio_device_put after incorrect return/goto
staging: alarm-dev: information leak in alarm_compat_ioctl()
iio:callback buffer: free the scan_mask
staging: alarm-dev: information leak in alarm_ioctl()
drivers: staging: zcache: fix compile error
staging: dwc2: fix value of dma_mask
Linus Torvalds [Thu, 6 Jun 2013 23:33:35 +0000 (16:33 -0700)]
Merge tag 'tty-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg Kroah-Hartman:
"Here are some small bugfixes, and one revert, of serial driver issues
that have been reported"
* tag 'tty-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250: Make SERIAL_8250_RUNTIME_UARTS work correctly"
serial: samsung: enable clock before clearing pending interrupts during init
serial/imx: disable hardware flow control at startup
Linus Torvalds [Thu, 6 Jun 2013 23:29:17 +0000 (16:29 -0700)]
Merge tag 'usb-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of USB bugfixes and new device ids for the 3.10-rc5
tree.
Nothing major here, a number of new device ids (and movement from the
option to the zte_ev driver of a number of ids that we had previously
gotten wrong, some xhci bugfixes, some usb-serial driver fixes that
were recently found, some host controller fixes / reverts, and a
variety of smaller other things"
* tag 'usb-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (29 commits)
USB: option,zte_ev: move most ZTE CDMA devices to zte_ev
USB: option: blacklist network interface on Huawei E1820
USB: whiteheat: fix broken port configuration
USB: serial: fix TIOCMIWAIT return value
USB: mos7720: fix hardware flow control
USB: keyspan: remove unused endpoint-array access
USB: keyspan: fix bogus array index
USB: zte_ev: fix broken open
USB: serial: Add Option GTM681W to qcserial device table.
USB: Serial: cypress_M8: Enable FRWD Dongle hidcom device
USB: EHCI: fix regression related to qh_refresh()
usbfs: Increase arbitrary limit for USB 3 isopkt length
USB: zte_ev: fix control-message timeouts
USB: mos7720: fix message timeouts
USB: iuu_phoenix: fix bulk-message timeout
USB: ark3116: fix control-message timeout
USB: mos7840: fix DMA to stack
USB: mos7720: fix DMA to stack
USB: visor: fix initialisation of Treo/Kyocera devices
USB: serial: fix Treo/Kyocera interrrupt-in urb context
...
Linus Torvalds [Thu, 6 Jun 2013 23:28:15 +0000 (16:28 -0700)]
Merge tag 'pci-v3.10-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"This fixes a crash when booting a 32-bit kernel via the EFI boot stub.
PCI ROM from EFI
x86/PCI: Map PCI setup data with ioremap() so it can be in highmem"
* tag 'pci-v3.10-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
x86/PCI: Map PCI setup data with ioremap() so it can be in highmem
Linus Torvalds [Thu, 6 Jun 2013 23:15:25 +0000 (16:15 -0700)]
Merge tag 'for-linus-v3.10-rc5' of git://oss.sgi.com/xfs/xfs
Pull more xfs updates from Ben Myers:
"Here are several fixes for filesystems with CRC support turned on:
fixes for quota, remote attributes, and recovery. There is also some
feature work related to CRCs: the implementation of CRCs for the inode
unlinked lists, disabling noattr2/attr2 options when appropriate, and
bumping the maximum number of ACLs.
I would have preferred to defer this last category of items to 3.11.
This would require setting a feature bit for the on-disk changes, so
there is some pressure to get these in 3.10. I believe this
represents the end of the CRC related queue.
- Rework of dquot CRCs
- Fix for remote attribute invalidation of a leaf
- Fix ordering of transaction replay in recovery
- Implement CRCs for inode unlinked list
- Disable noattr2/attr2 mount options when CRCs are enabled
- Bump the limitation of ACL entries for v5 superblocks"
* tag 'for-linus-v3.10-rc5' of git://oss.sgi.com/xfs/xfs:
xfs: increase number of ACL entries for V5 superblocks
xfs: disable noattr2/attr2 mount options for CRC enabled filesystems
xfs: inode unlinked list needs to recalculate the inode CRC
xfs: fix log recovery transaction item reordering
xfs: fix remote attribute invalidation for a leaf
xfs: rework dquot CRCs
net: Block MSG_CMSG_COMPAT in send(m)msg and recv(m)msg
This patch adds __sys_sendmsg and __sys_sendmsg as common helpers that accept
MSG_CMSG_COMPAT and blocks MSG_CMSG_COMPAT at the syscall entrypoints. It
also reverts some unnecessary checks in sys_socketcall.
Apparently I was suffering from underscore blindness the first time around.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Tested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tracing: Use current_uid() for critical time tracing
The irqsoff tracer records the max time that interrupts are disabled.
There are hooks in the assembly code that calls back into the tracer when
interrupts are disabled or enabled.
When they are enabled, the tracer checks if the amount of time they
were disabled is larger than the previous recorded max interrupts off
time. If it is, it creates a snapshot of the currently running trace
to store where the last largest interrupts off time was held and how
it happened.
During testing, this RCU lockdep dump appeared:
[ 1257.829021] ===============================
[ 1257.829021] [ INFO: suspicious RCU usage. ]
[ 1257.829021] 3.10.0-rc1-test+ #171 Tainted: G W
[ 1257.829021] -------------------------------
[ 1257.829021] /home/rostedt/work/git/linux-trace.git/include/linux/rcupdate.h:780 rcu_read_lock() used illegally while idle!
[ 1257.829021]
[ 1257.829021] other info that might help us debug this:
[ 1257.829021]
[ 1257.829021]
[ 1257.829021] RCU used illegally from idle CPU!
[ 1257.829021] rcu_scheduler_active = 1, debug_locks = 0
[ 1257.829021] RCU used illegally from extended quiescent state!
[ 1257.829021] 2 locks held by trace-cmd/4831:
[ 1257.829021] #0: (max_trace_lock){......}, at: [<ffffffff810e2b77>] stop_critical_timing+0x1a3/0x209
[ 1257.829021] #1: (rcu_read_lock){.+.+..}, at: [<ffffffff810dae5a>] __update_max_tr+0x88/0x1ee
[ 1257.829021]
[ 1257.829021] stack backtrace:
[ 1257.829021] CPU: 3 PID: 4831 Comm: trace-cmd Tainted: G W 3.10.0-rc1-test+ #171
[ 1257.829021] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./To be filled by O.E.M., BIOS SDBLI944.86P 05/08/2007
[ 1257.829021] 0000000000000001ffff880065f49da8ffffffff8153dd2bffff880065f49dd8
[ 1257.829021] ffffffff81092a00ffff88006bd78680ffff88007add75000000000000000003
[ 1257.829021] ffff88006bd78680ffff880065f49e18ffffffff810daebfffffffff810dae5a
[ 1257.829021] Call Trace:
[ 1257.829021] [<ffffffff8153dd2b>] dump_stack+0x19/0x1b
[ 1257.829021] [<ffffffff81092a00>] lockdep_rcu_suspicious+0x109/0x112
[ 1257.829021] [<ffffffff810daebf>] __update_max_tr+0xed/0x1ee
[ 1257.829021] [<ffffffff810dae5a>] ? __update_max_tr+0x88/0x1ee
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810dbf85>] update_max_tr_single+0x11d/0x12d
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810e2b15>] stop_critical_timing+0x141/0x209
[ 1257.829021] [<ffffffff8109569a>] ? trace_hardirqs_on+0xd/0xf
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810e3057>] time_hardirqs_on+0x2a/0x2f
[ 1257.829021] [<ffffffff811002b9>] ? user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff8109550c>] trace_hardirqs_on_caller+0x16/0x197
[ 1257.829021] [<ffffffff8109569a>] trace_hardirqs_on+0xd/0xf
[ 1257.829021] [<ffffffff811002b9>] user_enter+0xfd/0x107
[ 1257.829021] [<ffffffff810029b4>] do_notify_resume+0x92/0x97
[ 1257.829021] [<ffffffff8154bdca>] int_signal+0x12/0x17
What happened was entering into the user code, the interrupts were enabled
and a max interrupts off was recorded. The trace buffer was saved along with
various information about the task: comm, pid, uid, priority, etc.
The uid is recorded with task_uid(tsk). But this is a macro that uses rcu_read_lock()
to retrieve the data, and this happened to happen where RCU is blind (user_enter).
As only the preempt and irqs off tracers can have this happen, and they both
only have the tsk == current, if tsk == current, use current_uid() instead of
task_uid(), as current_uid() does not use RCU as only current can change its uid.
This fixes the RCU suspicious splat.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Dan Williams [Wed, 5 Jun 2013 20:26:27 +0000 (15:26 -0500)]
USB: option,zte_ev: move most ZTE CDMA devices to zte_ev
Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.
I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: Dan Williams <dcbw@redhat.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 6 Jun 2013 11:32:47 +0000 (13:32 +0200)]
USB: whiteheat: fix broken port configuration
When configuring the port (e.g. set_termios) the port minor number
rather than the port number was used in the request (and they only
coincide for minor number 0).
Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log