For performance reasons, when SMAP is in use, SMAP is left open for an
entire put_user_try { ... } put_user_catch(); block, however, calling
__put_user() in the middle of that block will close SMAP as the
STAC..CLAC constructs intentionally do not nest.
Furthermore, using __put_user() rather than put_user_ex() here is bad
for performance.
Thus, introduce new [compat_]save_altstack_ex() helpers that replace
__[compat_]save_altstack() for x86, being currently the only
architecture which supports put_user_try { ... } put_user_catch().
Reported-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Link: http://lkml.kernel.org/n/tip-es5p6y64if71k8p5u08agv9n@git.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MC13783 Chip Errata, Rev. 4 says, that depending on SPI clock
and main audio clock speed, the Audio Codec or Stereo DAC do sometimes
not start when programmed to do so. This is due to an internal clock
timing issue related to the loading of the SPI bits into the audio block.
On an i.MX27 based system, this issue lead to switched audio channels under
certain circumstances: RTC + Touch + Audio are used and loaded at startup.
The mentioned workaround of writing registers 40 and 41 two times is implemented
here.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bit 9 of PLL2,3 and 4 is reserved as '0'. The 24bit fractional part
should be split across each register in 8bit chunks.
Signed-off-by: Mike Dyer <mike.dyer@md-soft.co.uk> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
list_first_or_null() should test whether the list is empty and return
pointer to the first entry if not in a RCU safe manner. It's broken
in several ways.
* It compares __kernel @__ptr with __rcu @__next triggering the
following sparse warning.
net/core/dev.c:4331:17: error: incompatible types in comparison expression (different address spaces)
* It doesn't perform rcu_dereference*() and computes the entry address
using container_of() directly from the __rcu pointer which is
inconsitent with other rculist interface. As a result, all three
in-kernel users - net/core/dev.c, macvlan, cgroup - are buggy. They
dereference the pointer w/o going through read barrier.
* While ->next dereference passes through list_next_rcu(), the
compiler is still free to fetch ->next more than once and thus
nullify the "__ptr != __next" condition check.
Fix it by making list_first_or_null_rcu() dereference ->next directly
using ACCESS_ONCE() and then use list_entry_rcu() on it like other
rculist accessors.
v2: Paul pointed out that the compiler may fetch the pointer more than
once nullifying the condition check. ACCESS_ONCE() added on
->next dereference.
v3: Restored () around macro param which was accidentally removed.
Spotted by Paul.
Signed-off-by: Tejun Heo <tj@kernel.org> Reported-by: Fengguang Wu <fengguang.wu@intel.com> Cc: Dipankar Sarma <dipankar@in.ibm.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Li Zefan <lizefan@huawei.com> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm qos NO_POWER_OFF flag is checked twice during usb device suspend
to see if the usb port power off condition is met. This is redundant and
also will prevent the port from being powered off if the NO_POWER_OFF
flag is changed to 1 from 0 after the device was already suspended.
More detail in the following link.
http://marc.info/?l=linux-usb&m=136543949130865&w=2
This patch should be backported to kernels as old as 3.7, that
contain the commit f7ac7787ad361e31a7972e2854ed8dc2eedfac3b "usb/acpi:
Use ACPI methods to power off ports."
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hub driver's usb_port_suspend() routine doesn't handle errors
related to Link Power Management properly. It always returns failure,
it doesn't try to clean up the wakeup setting, (in the case of system
sleep) it doesn't try to go ahead with the port suspend regardless,
and it doesn't try to apply the new power-off mechanism.
This patch fixes these problems.
Note: Sarah fixed this patch to apply against 3.11, since the original
commit (4fae6f0fa86f92e6bc7429371b1e177ad0aaac66 "USB: handle LPM errors
during device suspend correctly") called usb_disable_remote_wakeup,
which won't be added until 3.12.
This patch should be backported to kernels as old as 3.5, that
contain the commit 8306095fd2c1100e8244c09bf560f97aca5a311d "USB:
Disable USB 3.0 LPM in critical sections.". There will be merge
conflicts, since LTM wasn't added until 3.6.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While reading the config parsing code I noticed this check is missing, without
this check config->desc.wTotalLength can end up with a value larger then the
dev->rawdescriptors length for the config, and when userspace then tries to
get the rawdescriptors bad things may happen.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Userspace can tell the kernel to power off any USB port, including ones
that are visible and connectible to users. When an attached USB device
goes into suspend, the port will be powered off if the
pm_qos_no_port_poweroff file for its port is set to 0, the device does
not have remote wakeup enabled, and the device is marked as persistent.
If the user disconnects the USB device while the port is powered off,
the current code does not handle that properly. If you disconnect a
device, and then run `lsusb -v -s` for the device, the device disconnect
does not get handled by the USB core. The runtime resume of the port
fails, because hub_port_debounce_be_connected() returns -ETIMEDOUT.
This means the port resume fails and khubd doesn't handle the USB device
disconnect. This leaves the device listed in lsusb, and the port's
runtime_status will be permanently marked as "error".
Fix this by ignoring the return value of hub_port_debounce_be_connected.
Users can disconnect USB devices while the ports are powered off, and we
must be able to handle that.
This patch should be backported to kernels as old as 3.9, that
contain the commit ad493e5e580546e6c3024b76a41535476da1546a "usb: add
usb port auto power off mechanism"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Lan Tianyu <tianyu.lan@intel.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7e8d5cd93fac ("USB: Add EHCI support for MX27 and MX31 based
boards") introduced code that could potentially lead to a NULL pointer
dereference on driver removal.
Fix this by checking for the value of pdata before dereferencing it.
Signed-off-by: Daniel Mack <zonque@gmail.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intel LPSS devices that are enumerated from ACPI have both MMIO and IRQ
resources returned in their _CRS method. However, Apple Macbook Air with
Haswell has LPSS devices enumerated from PCI bus instead and _CRS method
returns only an interrupt number (but the device has _HID set that causes
the scan handler to match it).
The current ACPI / LPSS code sets pdata->dev_desc only when MMIO resource
is found for the device and in case of Macbook Air it is never found. That
leads to a NULL pointer dereference in register_device_clock().
Correct this by always setting the pdata->dev_desc.
Reported-and-tested-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The removed check in the read_raw implementation was always true,
therefore remove it. This also fixes a bug, by closely inspecting
the code, one can notice the iio_validate_scan_mask_onehot() will
always return 1 and therefore the subsequent condition will always
succeed, therefore making the mxs_lradc_read_raw() function always
return -EINVAL; .
Signed-off-by: Marek Vasut <marex@denx.de> Tested-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Hector Palacios <hector.palacios@digi.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct iio_dev .trig field is to be used only by the IIO core,
the driver shall not fill this field. This fixes ugly crash when
the driver is compiled as a module and the module is rmmod'd.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dt282x_ai_insn_read() we call this macro like:
wait_for(!mux_busy(), comedi_error(dev, "timeout\n"); return -ETIME;);
Because the if statement doesn't have curly braces it means we always
return -ETIME and the function never succeeds.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The follow-up will fix nsproxy to discourage this type of issue from
happening again.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a server sends a lease break to a connection that doesn't have
opens with a lease key specified in the server response, we can't
find an open file to send an ack. Fix this by walking through
all connections we have.
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happens when we receive a lease break from a server, then
find an appropriate lease key in opened files and schedule the
oplock_break slow work. lw pointer isn't freed in this case.
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The client was in the middle of trying to send a frame when the
server->ssocket pointer got zeroed out. In most places, that we access
that pointer, the srv_mutex is held. There's only one spot that I see
that the server->ssocket pointer gets set and the srv_mutex isn't held.
This patch corrects that.
The upstream bug report was here:
https://bugzilla.kernel.org/show_bug.cgi?id=60557
Reported-by: Oleksii Shevchuk <alxchk@gmail.com> Signed-off-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from v3.10 (probably commit f91e2590410b: "tty: Signal
foreground group processes in hangup") disassociate_ctty() sends SIGCONT
if tty && on_exit. This breaks LSB test-suite, in particular test8 in
_exit.c and test40 in sigcon5.c.
Put the "!on_exit" check back to restore the old behaviour.
Review by Peter Hurley:
"Yes, this regression was introduced by me in that commit. The effect
of the regression is that ptys will receive a SIGCONT when, in similar
circumstances, ttys would not.
The fact that two test vectors accidentally tripped over this
regression suggests that some other apps may as well.
Thanks for catching this"
Signed-off-by: Oleg Nesterov <oleg@redhat.com> Reported-by: Karel Srot <ksrot@redhat.com> Reviewed-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a USB controller with XHCI_RESET_ON_RESUME goes to runtime suspend,
a reset will be performed upon runtime resume. Any previously suspended
devices attached to the controller will be re-enumerated at this time.
This will cause problems, for example, if an open system call on the
device triggered the resume (the open call will fail).
Note that this change is only relevant when persist_enabled is not set
for USB devices.
This patch should be backported to kernels as old as 3.0, that
contain the commit c877b3b2ad5cb9d4fe523c5496185cc328ff3ae9 "xhci: Add
reset on resume quirk for asrock p67 host".
The xHCI platform driver calls into usb_add_hcd to register the irq for
its platform device. It does not want the xHCI generic driver to
register an interrupt for it at all. The original code did that by
setting the XHCI_BROKEN_MSI quirk, which tells the xHCI driver to not
enable MSI or MSI-X for a PCI host.
Unfortunately, if CONFIG_PCI is enabled, and CONFIG_USB_DW3 is enabled,
the xHCI generic driver will attempt to register a legacy PCI interrupt
for the xHCI platform device in xhci_try_enable_msi(). This will result
in a bogus irq being registered, since the underlying device is a
platform_device, not a pci_device, and thus the pci_device->irq pointer
will be bogus.
Add a new quirk, XHCI_PLAT, so that the xHCI generic driver can
distinguish between a PCI device that can't handle MSI or MSI-X, and a
platform device that should not have its interrupts touched at all.
This quirk may be useful in the future, in case other corner cases like
this arise.
This patch should be backported to kernels as old as 3.9, that
contain the commit 00eed9c814cb8f281be6f0f5d8f45025dc0a97eb "USB: xhci:
correctly enable interrupts".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Yu Y Wang <yu.y.wang@intel.com> Tested-by: Yu Y Wang <yu.y.wang@intel.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8e44ddc3f3 ("powerpc/kvm/book3s: Add support for H_IPOLL and
H_XIRR_X in XICS emulation") added a call to get_tb() but didn't
include the header that defines it, and on some configs this means
book3s_xics.c fails to compile:
arch/powerpc/kvm/book3s_xics.c: In function ‘kvmppc_xics_hcall’:
arch/powerpc/kvm/book3s_xics.c:812:3: error: implicit declaration of function ‘get_tb’ [-Werror=implicit-function-declaration]
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SMAP register offsets in the versatile PCI controller code were
all off by four. (This didn't have any observable bad effects
because on this board PHYS_OFFSET is zero, and (a) writing zero to
the flags register at offset 0x10 has no effect and (b) the reset
value of the SMAP register is zero anyway, so failing to write SMAP2
didn't matter.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The versatile PCI controller code was confused between the
PCI I/O window (at 0x43000000) and the first PCI memory
window (at 0x44000000). Pass the correct base address to
pci_remap_io() so that PCI I/O accesses work.
Since the first PCI memory window isn't used at all (it's
an odd size), rename the associated variables and labels
so that it's clear that it isn't related to the I/O window.
This has been tested and confirmed to fix PCI I/O accesses
both on physical PB926+PCI backplane hardware and on QEMU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCI controller code for the Versatile board has never had the
correct IRQ mapping for hardware. For many years it had an odd
mapping ("all interrupts are int 27") which aligned with the
equivalent bug in QEMU. However as of commit 1bc39ac5dab265
the mapping changed and no longer matched either hardware or QEMU,
with the result that any PCI card beyond the first in QEMU would
not have functioning interrupts; for example a boot with a SCSI
controller would time out as follows:
------------
sym0: <895a> rev 0x0 at pci 0000:00:0d.0 irq 92
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.3
[...]
scsi 0:0:0:0: ABORT operation started
scsi 0:0:0:0: ABORT operation timed-out.
scsi 0:0:0:0: DEVICE RESET operation started
scsi 0:0:0:0: DEVICE RESET operation timed-out.
scsi 0:0:0:0: BUS RESET operation started
scsi 0:0:0:0: BUS RESET operation timed-out.
scsi 0:0:0:0: HOST RESET operation started
sym0: SCSI BUS has been reset
------------
Fix the mapping so that it matches real hardware (checked against the
schematics for PB926 and backplane, and tested against the hardware).
This allows PCI cards using interrupts to work on hardware for the
first time; this change will also work with QEMU 1.5 or later, where
the equivalent bugs in the modelling of the hardware have been fixed.
Although QEMU will attempt to autodetect whether the kernel is
expecting the long-standing "everything is int 27" mapping or the one
hardware has, for certainty we force it into "definitely behave like
hardware mode"; this will avoid unexpected surprises later if we
implement sparse irqs. This is harmless on hardware.
Thanks to Paul Gortmaker for bisecting the problem and finding an initial
solution, to Russell King for providing the correct interrupt mapping,
and to Guenter Roeck for providing an initial version of this patch
and prodding me into relocating the hardware and retesting everything.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a port of f2fe09b055e2 ("ARM: 7663/1: perf: fix ARMv7 EVTYPE_MASK
to include NSH bit") to arm64, which fixes the broken evtype mask to
include the NSH bit, allowing profiling at EL2.
This is a port of cb2d8b342aa0 ("ARM: 7698/1: perf: fix group validation
when using enable_on_exec") to arm64, which fixes the event validation
checking so that events in the OFF state are still considered when
enable_on_exec is true.
The PAR was exported as CRn == 7 and CRm == 0, but in fact the primary
coprocessor register number was determined by CRm for 64-bit coprocessor
registers as the user space API was modeled after the coprocessor
access instructions (see the ARM ARM rev. C - B3-1445).
However, just changing the CRn to CRm breaks the sorting check when
booting the kernel, because the internal kernel logic always treats CRn
as the primary register number, and it makes the table sorting
impossible to understand for humans.
Alternatively we could change the logic to always have CRn == CRm, but
that becomes unclear in the number of ways we do look up of a coprocessor
register. We could also have a separate 64-bit table but that feels
somewhat over-engineered. Instead, keep CRn the primary representation
of the primary coproc. register number in-kernel and always export the
primary number as CRm as per the existing user space ABI.
Note: The TTBR registers just magically worked because they happened to
follow the CRn(0) regs and were considered CRn(0) in the in-kernel
representation.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Kim Phillips <kim.phillips@linaro.org> Cc: Gleb Natapov <gleb@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Russell King <linux@arm.linux.org.uk> Cc: Jonghwan Choi <jhbird.choi@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent series has added CPU numbers to a lot of dts files,
but unfortunately in a few cases the #address-cells
and #size-cells values are missing, which causes build warnings.
This adds the missing ones for sunxi and sama5 that I found
through build testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coupled cpuidle waiting loop clears pending pokes before
entering the safe state. If a poke arrives just before the
pokes are cleared, but after the while loop condition checks,
the poke will be lost and the cpu will stay in the safe state
until another interrupt arrives. This may cause the cpu that
sent the poke to spin in the ready loop with interrupts off
until another cpu receives an interrupt, and if no other cpus
have interrupts routed to them it can spin forever.
Change the return value of cpuidle_coupled_clear_pokes to
return if a poke was cleared, and move the need_resched()
checks into the callers. In the waiting loop, if
a poke was cleared restart the loop to repeat the while
condition checks.
Reported-by: Neil Zhang <zhangwm@marvell.com> Signed-off-by: Colin Cross <ccross@android.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joseph Lo <josephl@nvidia.com> reported a lockup on Tegra20 caused
by a race condition in coupled cpuidle. When two or more cpus
enter idle at the same time, the first cpus to arrive may go to the
ready loop without processing pending pokes from the last cpu to
arrive.
This patch adds a check for pending pokes once all cpus have been
synchronized in the ready loop and resets the coupled state and
retries if any cpus failed to handle their pending poke.
Retrying on all cpus may trigger the same issue again, so this patch
also adds a check to ensure that each cpu has received at least one
poke between when it enters the waiting loop and when it moves on to
the ready loop.
Reported-and-tested-by: Joseph Lo <josephl@nvidia.com> Tested-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Colin Cross <ccross@android.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xen_pm_init was unconditionally setting pm_power_off and arm_pm_restart
function pointers. This breaks multi-platform kernels. Make this
conditional on running as a Xen guest and make it a late_initcall to
ensure it is setup after platform code for Dom0.
With the current implementation, the callback in the tail of the list
can be added twice, because the check done in
gnttab_request_free_callback is bogus, callback->next can be NULL if
it is the last callback in the list. If we add the same callback twice
we end up with an infinite loop, were callback == callback->next.
Replace this check with a proper one that iterates over the list to
see if the callback has already been added.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Matt Wilson <msw@amazon.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When adding cpuidle support to pSeries, we introduced two
regressions:
- The new cpuidle backend driver only works under hypervisors
supporting the "SLPLAR" option, which isn't the case of the
old POWER4 hypervisor and the HV "light" used on js2x blades
- The cpuidle driver registers fairly late, meaning that for
a significant portion of the boot process, we end up having
all threads spinning. This slows down the boot process and
increases the overall resource usage if the hypervisor has
shared processors.
This fixes both by implementing a "default" idle that will cede
to the hypervisor when possible, in a very simple way without
all the bells and whisles of cpuidle.
Reported-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Acked-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normally when we haven't implemented an alignment handler for
a load or store instruction the process will be terminated.
The alignment handler uses the DSISR (or a pseudo one) to locate
the right handler. Unfortunately ldbrx and stdbrx overlap lfs and
stfs so we incorrectly think ldbrx is an lfs and stdbrx is an
stfs.
This bug is particularly nasty - instead of terminating the
process we apply an incorrect fixup and continue on.
With more and more overlapping instructions we should stop
creating a pseudo DSISR and index using the instruction directly,
but for now add a special case to catch ldbrx/stdbrx.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
crypto_larval_lookup should only return a larval if it created one.
Any larval created by another entity must be processed through
crypto_larval_wait before being returned.
Otherwise this will lead to a larval being killed twice, which
will most likely lead to a crash.
This patch fixes an out-of-bounds error in sd_read_cache_type(), found
by Google's AddressSanitizer tool. When the loop ends, we know that
"offset" lies beyond the end of the data in the buffer, so no Caching
mode page was found. In theory it may be present, but the buffer size
is limited to 512 bytes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_peb_for_wl() removes the PEB from the free list.
If the WL subsystem detects that no wear leveling is needed
it cancels the operation and drops the gained PEB.
In this case we have to put the PEB back into the free list.
This issue was introduced with commit ed4b7021c
(UBI: remove PEB from free tree in get_peb_for_wl()).
Right now the Makefile for the mpt3sas driver does not even allow the
driver to be built into the kernel. So fix that up, as there doesn't
seem to be any obvious reason why this shouldn't be done.
The Network Manager attempts to use all 3 interfaces above without
filtering the managed interface type. As the result, 3 identical
interfaces are displayed under network manager. If user happens to
click on an entry under which its interface is uap0 or p2p0, the
association will fail.
Work around it by removing the creation of AP and P2P interfaces
at driver loading time. These interfaces can be added with 'iw' or
other applications manually when they are needed.
Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Avinash Patil <patila@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This affects xen pv guests with sufficiently old versions of xen and
sufficiently new hardware. On such a system, a guest with a btrfs
root won't even boot.
Signed-off-by: John Haxby <john.haxby@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Reported-by: Michael Marineau <michael.marineau@coreos.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes a long-standing bug that has been reported by many
users: on some Armada 370 platforms, only the network interface that
has been used in U-Boot to tftp the kernel works properly in
Linux. The other network interfaces can see a 'link up', but are
unable to transmit data. The reports were generally made on the Armada
370-based Mirabox, but have also been given on the Armada 370-RD
board.
The network MAC in the Armada 370/XP (supported by the mvneta driver
in Linux) has a functionality that allows it to continuously poll the
PHY and directly update the MAC configuration accordingly (speed,
duplex, etc.). The very first versions of the driver submitted for
review were using this hardware mechanism, but due to this, the driver
was not integrated with the kernel phylib. Following reviews, the
driver was changed to use the phylib, and therefore a software based
polling. In software based polling, Linux regularly talks to the PHY
over the MDIO bus, and sees if the link status has changed. If it's
the case then the adjust_link() callback of the driver is called to
update the MAC configuration accordingly.
However, it turns out that the adjust_link() callback was not
configuring the hardware in a completely correct way: while it was
setting the speed and duplex bits correctly, it wasn't telling the
hardware to actually take into account those bits rather than what the
hardware-based PHY polling mechanism has concluded. So, in fact the
adjust_link() callback was basically a no-op.
However, the network happened to be working because on the network
interfaces used by U-Boot for tftp on Armada 370 platforms because the
hardware PHY polling was enabled by the bootloader, and left enabled
by Linux. However, the second network interface not used for tftp (or
both network interfaces if the kernel is loaded from USB, NAND or SD
card) didn't had the hardware PHY polling enabled.
This patch fixes this situation by:
(1) Making sure that the hardware PHY polling is disabled by clearing
the MVNETA_PHY_POLLING_ENABLE bit in the MVNETA_UNIT_CONTROL
register in the driver ->probe() function.
(2) Making sure that the duplex and speed selections made by the
adjust_link() callback are taken into account by clearing the
MVNETA_GMAC_AN_SPEED_EN and MVNETA_GMAC_AN_DUPLEX_EN bits in the
MVNETA_GMAC_AUTONEG_CONFIG register.
This patch has been tested on Armada 370 Mirabox, and now both network
interfaces are usable after boot.
[ Problem introduced by commit c5aff18 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") ]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Jochen De Smet <jochen.armkernel@leahnim.org> Cc: Peter Sanford <psanford@nearbuy.io> Cc: Ethan Tuttle <ethan@ethantuttle.com> Cc: Chény Yves-Gael <yves@cheny.fr> Cc: Ryan Press <ryan@presslab.us> Cc: Simon Guinot <simon.guinot@sequanux.org> Cc: vdonnefort@lacie.com Cc: stable@vger.kernel.org Acked-by: Jason Cooper <jason@lakedaemon.net> Tested-by: Vincent Donnefort <vdonnefort@gmail.com> Tested-by: Yves-Gael Cheny <yves@cheny.fr> Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tcp_v6_do_rcv() code, when processing pkt options, we soley work
on our skb clone opt_skb that we've created earlier before entering
tcp_rcv_established() on our way. However, only in condition ...
if (np->rxopt.bits.rxtclass)
np->rcv_tclass = ipv6_get_dsfield(ipv6_hdr(skb));
... we work on skb itself. As we extract every other information out
of opt_skb in ipv6_pktoptions path, this seems wrong, since skb can
already be released by tcp_rcv_established() earlier on. When we try
to access it in ipv6_hdr(), we will dereference freed skb.
[ Bug added by commit 4c507d2897bd9b ("net: implement IP_RECVTOS for
IP_PKTOPTIONS") ]
Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b67bfe0d42cac56c512dd5da4b1b347a23f4b70a ("hlist: drop
the node parameter from iterators") changed the behavior of
hlist_for_each_entry_safe to leave the p argument NULL.
Fix this up by tracking the last argument.
Reported-by: Michele Baldessari <michele@acksyn.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Tested-by: Michele Baldessari <michele@acksyn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We used to poll vhost queue before making DMA is done, this is racy if vhost
thread were waked up before marking DMA is done which can result the signal to
be missed. Fix this by always polling the vhost thread before DMA is done.
Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turning off led on port 0 of the 5719 serdes causes all other ports to
lose power and stop functioning. Add tg3_phy_led_bug() function to check
for this condition. We use a switch() in tg3_phy_led_bug() for
consistency with the tg3_phy_power_bug() function.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RFC 4443 has defined two additional codes for ICMPv6 type 1 (destination
unreachable) messages:
5 - Source address failed ingress/egress policy
6 - Reject route to destination
Now they are treated as protocol error and icmpv6_err_convert() converts them
to EPROTO.
RFC 4443 says:
"Codes 5 and 6 are more informative subsets of code 1."
Treat codes 5 and 6 as code 1 (EACCES)
Btw, connect() returning -EPROTO confuses firefox, so that fallback to
other/IPv4 addresses does not work:
https://bugzilla.mozilla.org/show_bug.cgi?id=910773
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While looking into MLDv1/v2 code, I noticed that bridging code does
not convert it's max delay into jiffies for MLDv2 messages as we do
in core IPv6' multicast code.
RFC3810, 5.1.3. Maximum Response Code says:
The Maximum Response Code field specifies the maximum time allowed
before sending a responding Report. The actual time allowed, called
the Maximum Response Delay, is represented in units of milliseconds,
and is derived from the Maximum Response Code as follows: [...]
As we update timers that work with jiffies, we need to convert it.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Linus Lüssing <linus.luessing@web.de> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8728c544a9cbdc ("net: dev_pick_tx() fix") and commit b6fe83e9525a ("bonding: refine IFF_XMIT_DST_RELEASE capability")
are quite incompatible : Queue selection is disabled because skb
dst was dropped before entering bonding device.
This causes major performance regression, mainly because TCP packets
for a given flow can be sent to multiple queues.
This is particularly visible when using the new FQ packet scheduler
with MQ + FQ setup on the slaves.
We can safely revert the first commit now that 416186fbf8c5b
("net: Split core bits of netdev_pick_tx into __netdev_pick_tx")
properly caps the queue_index.
Reported-by: Xi Wang <xii@google.com> Diagnosed-by: Xi Wang <xii@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tom Herbert <therbert@google.com> Cc: Alexander Duyck <alexander.h.duyck@intel.com> Cc: Denys Fedorysychenko <nuclearcat@nuclearcat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Should a connect fail, if the publication/server is unavailable or
due to some other error, a positive value will be returned and errno
is never set. If the application code checks for an explicit zero
return from connect (success) or a negative return (failure), it
will not catch the error and subsequent send() calls will fail as
shown from the strace snippet below.
The reason for this behaviour is that TIPC wrongly inverts error
codes set in sk_err.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 90ba9b19 (tcp: tcp_make_synack() can use alloc_skb()), Eric changed
the call to sock_wmalloc in tcp_make_synack to alloc_skb. In doing so,
the netfilter owner match lost its ability to block the SYNACK packet on
outbound listening sockets. Revert the change, restoring the owner match
functionality.
This closes netfilter bugzilla #847.
Signed-off-by: Phil Oester <kernel@linuxace.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocating skbs when sending out neighbour discovery messages
currently uses sock_alloc_send_skb() based on a per net namespace
socket and thus share a socket wmem buffer space.
If a netdevice is temporarily unable to transmit due to carrier
loss or for other reasons, the queued up ndisc messages will cosnume
all of the wmem space and will thus prevent from any more skbs to
be allocated even for netdevices that are able to transmit packets.
The number of neighbour discovery messages sent is very limited,
use of alloc_skb() bypasses the socket wmem buffer size enforcement
while the manual call to skb_set_owner_w() maintains the socket
reference needed for the IPv6 output path.
This patch has orginally been posted by Eric Dumazet in a modified
form.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Stephen Warren <swarren@nvidia.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Chris Clark <chris.clark@alcatel-lucent.com> Bisected-by: Chris Clark <chris.clark@alcatel-lucent.com> Tested-by: Chris Clark <chris.clark@alcatel-lucent.com> Suggested-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Chris Clark <chris.clark@alcatel-lucent.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The zero value means that tsecr is not valid, so it's a special case.
tsoffset is used to customize tcp_time_stamp for one socket.
tsoffset is usually zero, it's used when a socket was moved from one
host to another host.
Currently this issue affects logic of tcp_rcv_rtt_measure_ts. Due to
incorrect value of rcv_tsecr, tcp_rcv_rtt_measure_ts sets rto to
TCP_RTO_MAX.
Reported-by: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: Andrey Vagin <avagin@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds another entry (HP hs2434 Mobile Broadband) to the list
of exceptional devices that require a zero length packet in order to
function properly. This list was added in commit 844e88f0. The hs2434
is manufactured by Sierra Wireless, who also produces the MC7710,
which the ZLP exception list was created for in the first place. So
hopefully it is just this one producer's devices that will need this
workaround.
Tested on a DM1-4310NR HP notebook, which does not function without this
change.
Signed-off-by: Rob Gardner <robmatic@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fba875591 ("disable TX in be_close()") disabled TX in be_close()
to protect be_xmit() from touching freed up queues in the AER recovery
flow. But, TX must be disabled *before* cleaning up TX completions in
the close() path, not after. This allows be_tx_compl_clean() to free up
all TX-req skbs that were notified to the HW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 385904f819e3 ('sfc: Don't use
efx_filter_{build,hash,increment}() for default MAC filters') used the
wrong name to find the index of default RX MAC filters at insertion/
update time. This could result in memory corruption and would in any
case silently fail to update the filter.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56b765b79 ("htb: improved accuracy at high rates")
broke the "linklayer atm" handling.
tc class add ... htb rate X ceil Y linklayer atm
The linklayer setting is implemented by modifying the rate table
which is send to the kernel. No direct parameter were
transferred to the kernel indicating the linklayer setting.
The commit 56b765b79 ("htb: improved accuracy at high rates")
removed the use of the rate table system.
To keep compatible with older iproute2 utils, this patch detects
the linklayer by parsing the rate table. It also supports future
versions of iproute2 to send this linklayer parameter to the
kernel directly. This is done by using the __reserved field in
struct tc_ratespec, to convey the choosen linklayer option, but
only using the lower 4 bits of this field.
Linklayer detection is limited to speeds below 100Mbit/s, because
at high rates the rtab is gets too inaccurate, so bad that
several fields contain the same values, this resembling the ATM
detect. Fields even start to contain "0" time to send, e.g. at
1000Mbit/s sending a 96 bytes packet cost "0", thus the rtab have
been more broken than we first realized.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VLAN code needs to know the length of the per-port VLAN bitmap to
perform its most basic operations (retrieving VLAN informations, removing
VLANs, forwarding database manipulation, etc). Unfortunately, in the
current implementation we are using a macro that indicates the bitmap
size in longs in places where the size in bits is expected, which in
some cases can cause what appear to be random failures.
Use the correct macro.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
getsockopt PACKET_STATISTICS returns tp_packets + tp_drops. Commit ee80fbf301 ("packet: account statistics only in tpacket_stats_u")
cleaned up the getsockopt PACKET_STATISTICS code.
This also changed semantics. Historically, tp_packets included
tp_drops on return. The commit removed the line that adds tp_drops
into tp_packets.
This patch reinstates the old semantics.
Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the repair mode is turned off, the write queue seqs are
updated so that the whole queue is considered to be 'already sent.
The "when" field must be set for such skb. It's used in tcp_rearm_rto
for example. If the "when" field isn't set, the retransmit timeout can
be calculated incorrectly and a tcp connected can stop for two minutes
(TCP_RTO_MAX).
Acked-by: Pavel Emelyanov <xemul@parallels.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Cc: James Morris <jmorris@namei.org> Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Cc: Patrick McHardy <kaber@trash.net> Signed-off-by: Andrey Vagin <avagin@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not allowed for an ipv6 packet to contain multiple fragmentation
headers. So discard packets which were already reassembled by
fragmentation logic and send back a parameter problem icmp.
The updates for RFC 6980 will come in later, I have to do a bit more
research here.
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of the max_addresses check attackers were able to disable privacy
extensions on an interface by creating enough autoconfigured addresses:
<http://seclists.org/oss-sec/2012/q4/292>
But the check is not actually needed: max_addresses protects the
kernel to install too many ipv6 addresses on an interface and guards
addrconf_prefix_rcv to install further addresses as soon as this limit
is reached. We only generate temporary addresses in direct response of
a new address showing up. As soon as we filled up the maximum number of
addresses of an interface, we stop installing more addresses and thus
also stop generating more temp addresses.
Even if the attacker tries to generate a lot of temporary addresses
by announcing a prefix and removing it again (lifetime == 0) we won't
install more temp addresses, because the temporary addresses do count
to the maximum number of addresses, thus we would stop installing new
autoconfigured addresses when the limit is reached.
This patch fixes CVE-2013-0343 (but other layer-2 attacks are still
possible).
Thanks to Ding Tianhong to bring this topic up again.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Ding Tianhong <dingtianhong@huawei.com> Cc: George Kargiotakis <kargig@void.gr> Cc: P J P <ppandit@redhat.com> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Acked-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent fix d9bf5f1309 "tun: compare with 0 instead of total_len" is
not totally correct. Because "len" and "sizeof()" are size_t type, that
means they are never less than zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the iproute2 command `bridge vlan show`, after switching from
rtgenmsg to ifinfomsg.
Let's start with a little history:
Feb 20: Vlad Yasevich got his VLAN-aware bridge patchset included in
the 3.9 merge window.
In the kernel commit 6cbdceeb, he added attribute support to
bridge GETLINK requests sent with rtgenmsg.
Mar 6th: Vlad got this iproute2 reference implementation of the bridge
vlan netlink interface accepted (iproute2 9eff0e5c)
Apr 25th: iproute2 switched from using rtgenmsg to ifinfomsg (63338dca)
http://patchwork.ozlabs.org/patch/239602/
http://marc.info/?t=136680900700007
Apr 28th: Linus released 3.9
Apr 30th: Stephen released iproute2 3.9.0
The `bridge vlan show` command haven't been working since the switch to
ifinfomsg, or in a released version of iproute2. Since the kernel side
only supports rtgenmsg, which iproute2 switched away from just prior to
the iproute2 3.9.0 release.
I haven't been able to find any documentation, about neither rtgenmsg
nor ifinfomsg, and in which situation to use which, but kernel commit 88c5b5ce seams to suggest that ifinfomsg should be used.
Fixing this in kernel will break compatibility, but I doubt that anybody
have been using it due to this bug in the user space reference
implementation, at least not without noticing this bug. That said the
functionality is still fully functional in 3.9, when reversing iproute2
commit 63338dca.
This could also be fixed in iproute2, but thats an ugly patch that would
reintroduce rtgenmsg in iproute2, and from searching in netdev it seams
like rtgenmsg usage is discouraged. I'm assuming that the only reason
that Vlad implemented the kernel side to use rtgenmsg, was because
iproute2 was using it at the time.
Signed-off-by: Asbjoern Sloth Toennesen <ast@fiberby.net> Reviewed-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using inner-id for tunnel id is not safe in some rare cases.
E.g. packets coming from multiple sources entering same tunnel
can have same id. Therefore on tunnel packet receive we
could have packets from two different stream but with same
source and dst IP with same ip-id which could confuse ip packet
reassembly.
Following patch reverts optimization from commit 490ab08127 (IP_GRE: Fix IP-Identification.)
Signed-off-by: Pravin B Shelar <pshelar@nicira.com> CC: Jarno Rajahalme <jrajahalme@nicira.com> CC: Ansis Atteka <aatteka@nicira.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
netlink dump operations take module as parameter to hold
reference for entire netlink dump duration.
Currently it holds ref only on genl module which is not correct
when we use ops registered to genl from another module.
Following patch adds module pointer to genl_ops so that netlink
can hold ref count on it.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com> CC: Jesse Gross <jesse@nicira.com> CC: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of genl-family with parallel ops off, dumpif() callback
is expected to run under genl_lock, But commit def3117493eafd9df
(genl: Allow concurrent genl callbacks.) changed this behaviour
where only first dumpit() op was called under genl-lock.
For subsequent dump, only nlk->cb_lock was taken.
Following patch fixes it by defining locked dumpit() and done()
callback which takes care of genl-locking.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com> CC: Jesse Gross <jesse@nicira.com> CC: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix ipgre_header() (header_ops->create) to return the correct
amount of bytes pushed. Most callers of dev_hard_header() seem
to care only if it was success, but af_packet.c uses it as
offset to the skb to copy from userspace only once. In practice
this fixes packet socket sendto()/sendmsg() to gre tunnels.
Cc: Pravin B Shelar <pshelar@nicira.com> Signed-off-by: Timo Teräs <timo.teras@iki.fi> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case a subtree did not match we currently stop backtracking and return
NULL (root table from fib_lookup). This could yield in invalid routing
table lookups when using subtrees.
Instead continue to backtrack until a valid subtree or node is found
and return this match.
Also remove unneeded NULL check.
Reported-by: Teco Boot <teco@inf-net.nl> Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Cc: David Lamparter <equinox@diac24.net> Cc: <boutier@pps.univ-paris-diderot.fr> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While investigating about strange increase of retransmit rates
on hosts ~24 days after boot, Van found hystart was disabled
if ca->epoch_start was 0, as following condition is true
when tcp_time_stamp high order bit is set.
(s32)(tcp_time_stamp - ca->epoch_start) < HZ
Quoting Van :
At initialization & after every loss ca->epoch_start is set to zero so
I believe that the above line will turn off hystart as soon as the 2^31
bit is set in tcp_time_stamp & hystart will stay off for 24 days.
I think we've observed that cubic's restart is too aggressive without
hystart so this might account for the higher drop rate we observe.
Diagnosed-by: Van Jacobson <vanj@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we are reading an uninitialized value for the max_delay
variable when snooping an MLD query message of invalid length and would
update our timers with that.
Fixing this by simply ignoring such broken MLD queries (just like we do
for IGMP already).
This is a regression introduced by:
"bridge: disable snooping if there is no querier" (b00589af3b04)
Reported-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Linus Lüssing <linus.luessing@web.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise, on neighbour creation, bond_neigh_init() will be called with a
foreign netdev.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev->ndo_neigh_setup() might need some of the values of neigh_parms, so
populate them before calling it.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df8ef8f3aaa6692970a436204c4429210addb23a
macvlan: add FDB bridge ops and macvlan flags
added a flags field to macvlan, which can be
controlled from userspace.
The idea is to make the interface future-proof
so we can add flags and not new fields.
However, flags value isn't validated, as a result,
userspace can't detect which flags are supported.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible to assign an invalid value to the net.core.somaxconn
sysctl variable, because there is no checks at all.
The sk_max_ack_backlog field of the sock structure is defined as
unsigned short. Therefore, the backlog argument in inet_listen()
shouldn't exceed USHRT_MAX. The backlog argument in the listen() syscall
is truncated to the somaxconn value. So, the somaxconn value shouldn't
exceed 65535 (USHRT_MAX).
Also, negative values of somaxconn are meaningless.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru> Reported-by: Changli Gao <xiaosuo@gmail.com> Suggested-by: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5c766d642 ("ipv4: introduce address lifetime") leaves the ifa
resource that was allocated via inet_alloc_ifa() unfreed when returning
the function with -EINVAL. Thus, free it first via inet_free_ifa().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Reviewed-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When userspace passes a large priority value
the assignment of the unsigned value hopt->prio
to signed int cl->prio causes cl->prio to become negative and the
comparison is with TC_HTB_NUMPRIO is always false.
The result is that HTB crashes by referencing outside
the array when processing packets. With this patch the large value
wraps around like other values outside the normal range.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid overlapping register regions by making the initial blklen of a new
node 1. If a register write occurs to a yet uncached register, that is
lower than but near an existing node's base_reg, a new node is created
and it's blklen is set to an arbitrary value (sizeof(*rbnode)). That may
cause this node to overlap with another node. Those nodes should be merged,
but this merge doesn't happen yet, so this patch at least makes the initial
blklen small enough to avoid hitting the wrong node, which may otherwise
lead to severe breakage.
Signed-off-by: David Jander <david@protonic.nl> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Zhouping Liu <zliu@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PREEMPT is enabled, Linux will not be able to boot and warn:
[ 4.127825] ------------[ cut here ]------------
[ 4.133376] WARNING: at init/main.c:699 do_one_initcall+0x150/0x158()
[ 4.140738] initcall xen_init_events+0x0/0x10c returned with preemption imbalance
This is because xen_percpu_init uses get_cpu but doesn't have the corresponding
put_cpu.
projects / karo-tx-linux.git / log