powerpc/fsl: Add support for Integrated Flash Controller
Integrated Flash Controller supports various flashes like NOR, NAND
and other devices using NOR, NAND and GPCM Machine available on it.
IFC supports four chip selects.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Liu Shuo <b35362@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 28 Nov 2011 19:58:53 +0000 (13:58 -0600)]
powerpc/fsl: update compatiable on fsl 16550 uart nodes
The Freescale serial port's are pretty much a 16550, however there are
some FSL specific bugs and features. Add a "fsl,ns16550" compatiable
string to allow code to handle those FSL specific issues.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Andy Fleming [Wed, 4 Jan 2012 21:28:31 +0000 (15:28 -0600)]
powerpc: Add TBI PHY node to first MDIO bus
Systems which use the fsl_pq_mdio driver need to specify an
address for TBI PHY transactions such that the address does
not conflict with any PHYs on the bus (all transactions to
that address are directed to the onboard TBI PHY). The driver
used to scan for a free address if no address was specified,
however this ran into issues when the PHY Lib was fixed so
that all MDIO transactions were protected by a mutex. As it
is, the code was meant to serve as a transitional tool until
the device trees were all updated to specify the TBI address.
The best fix for the mutex issue was to remove the scanning code,
but it turns out some of the newer SoCs have started to omit
the tbi-phy node when SGMII is not being used. As such, these
devices will now fail unless we add a tbi-phy node to the first
mdio controller.
Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
"fix of_flat_dt_is_compatible() to match the full compatible string"
causes silent boot death on the sbc8349 board because it was
just looking for 8349 and not 8349E -- as originally there
were non-E (no SEC/encryption) chips available. Just add the
E to the board detection string since all boards I've seen
were manufactured with the E versions.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 1 Dec 2011 05:38:18 +0000 (23:38 -0600)]
powerpc/fsl-pci: Allow 64-bit PCIe devices to DMA to any memory address
There is an issue on FSL-BookE 64-bit devices (P5020) in which PCIe
devices that are capable of doing 64-bit DMAs (like an Intel e1000) do
not function and crash the kernel if we have >4G of memory in the system.
The reason is that the existing code only sets up one inbound window for
access to system memory across PCIe. That window is limited to a 32-bit
address space. So on systems we'll end up utilizing SWIOTLB for dma
mappings. However SWIOTLB dma ops implement dma_alloc_coherent() as
dma_direct_alloc_coherent(). Thus we can end up with dma addresses that
are not accessible because of the inbound window limitation.
We could possibly set the SWIOTLB alloc_coherent op to
swiotlb_alloc_coherent() however that does not address the issue since
the swiotlb_alloc_coherent() will behave almost identical to
dma_direct_alloc_coherent() since the devices coherent_dma_mask will be
greater than any address allocated by swiotlb_alloc_coherent() and thus
we'll never bounce buffer it into a range that would be dma-able.
The easiest and best solution is to just make it so that a 64-bit
capable device is able to DMA to any internal system address.
We accomplish this by opening up a second inbound window that maps all
of memory above the internal SoC address width so we can set it up to
access all of the internal SoC address space if needed.
We than fixup the dma_ops and dma_offset for PCIe devices with a dma
mask greater than the maximum internal SoC address.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
where:
A => B and A -> B means A calls B, but
=> means A will call B through function name, and B will definitely be
called.
-> means A will call B through function pointer, so B might not be
called if the function pointer is not set.
So error happens when only one of probe_hcall_entry and probe_hcall_exit
get called during a hcall.
This patch tries to move the preempt count operations from
probe_hcall_entry and probe_hcall_exit to its callers.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> CC: stable@kernel.org [v2.6.32+] Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When using a >8bpp framebuffer, offb advertises truecolor, not directcolor,
and doesn't touch the color map even if it has a corresponding access method
for the real hardware.
Thus it needs to set the pseudo-palette with all 3 components of the color,
like other truecolor framebuffers, not with copies of the color index like
a directcolor framebuffer would do.
This went unnoticed for a long time because it's pretty hard to get offb
to kick in with anything but 8bpp (old BootX under MacOS will do that and
qemu does it).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> CC: stable@kernel.org
offb: Add palette hack for qemu "standard vga" framebuffer
We rename the mach64 hack to "simple" since that's also applicable
to anything using VGA-style DAC IO ports (set to 8-bit DAC) and we
use it for qemu vga.
Note that this is keyed on a device-tree "compatible" property that
is currently only set by an upcoming version of SLOF when using the
qemu "pseries" platform. This is on purpose as other qemu ppc platforms
using OpenBIOS aren't properly setting the DAC to 8-bit at the time of
the writing of this patch.
We can fix OpenBIOS later to do that and add the required property, in
which case it will be matched by this change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Suzuki Poulose [Tue, 20 Dec 2011 21:20:38 +0000 (21:20 +0000)]
powerpc/boot: Change the WARN to INFO for boot wrapper overlap message
commit c55aef0e5bc6 ("powerpc/boot: Change the load address
for the wrapper to fit the kernel") introduced a WARNING to
inform the user that the uncompressed kernel would overlap
the boot uncompressing wrapper code. Change it to an INFO.
I initially thought, this would be a 'WARNING' for the those
boards, where the link_address should be fixed, so that the
user can take actions accordingly.
Changing the same to INFO.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Josh Boyer [Tue, 20 Dec 2011 15:41:28 +0000 (10:41 -0500)]
powerpc/44x: Fix build error on currituck platform
The MPIC_PRIMARY define was recently made "default" and the meaning was
inverted to MPIC_SECONDARY. This causes compile errors in currituck now, so
fix it to the new manner of allocating mpics.
Suzuki Poulose [Wed, 14 Dec 2011 22:59:57 +0000 (22:59 +0000)]
powerpc/boot: Change the load address for the wrapper to fit the kernel
The wrapper code which uncompresses the kernel in case of a 'ppc' boot
is by default loaded at 0x00400000 and the kernel will be uncompressed
to fit the location 0-0x00400000. But with dynamic relocations, the size
of the kernel may exceed 0x00400000(4M). This would cause an overlap
of the uncompressed kernel and the boot wrapper, causing a failure in
boot.
The message looks like :
zImage starting: loaded at 0x00400000 (sp: 0x0065ffb0)
Allocating 0x5ce650 bytes for kernel ...
Insufficient memory for kernel at address 0! (_start=00400000, uncompressed size=00591a20)
This patch shifts the load address of the boot wrapper code to the next
higher MB, according to the size of the uncompressed vmlinux.
With the patch, we get the following message while building the image :
WARN: Uncompressed kernel (size 0x5b0344) overlaps the address of the wrapper(0x400000)
WARN: Fixing the link_address of wrapper to (0x600000)
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
virt_phys_offset = effective. kernel virt base - kernstart_addr
I have tested the patches on 440x platforms only. However this should
work fine for PPC_47x also, as we only depend on the runtime address
and the current TLB XLAT entry for the startup code, which is available
in r25. I don't have access to a 47x board yet. So, it would be great if
somebody could test this on 47x.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Tony Breeds <tony@bakeyournoodle.com> Cc: Josh Boyer <jwboyer@gmail.com> Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
On BookE, we need __va() & __pa() early in the boot process to access
the device tree.
Currently this has been defined as :
#define __va(x) ((void *)(unsigned long)((phys_addr_t)(x) -
PHYSICAL_START + KERNELBASE)
where:
PHYSICAL_START is kernstart_addr - a variable updated at runtime.
KERNELBASE is the compile time Virtual base address of kernel.
This won't work for us, as kernstart_addr is dynamic and will yield different
results for __va()/__pa() for same mapping.
e.g.,
Let the kernel be loaded at 64MB and KERNELBASE be 0xc0000000 (same as
PAGE_OFFSET).
In this case, we would be mapping 0 to 0xc0000000, and kernstart_addr = 64M
Now __va(1MB) = (0x100000) - (0x4000000) + 0xc0000000
= 0xbc100000 , which is wrong.
it should be : 0xc0000000 + 0x100000 = 0xc0100000
On platforms which support AMP, like PPC_47x (based on 44x), the kernel
could be loaded at highmem. Hence we cannot always depend on the compile
time constants for mapping.
Here are the possible solutions:
1) Update kernstart_addr(PHSYICAL_START) to match the Physical address of
compile time KERNELBASE value, instead of the actual Physical_Address(_stext).
The disadvantage is that we may break other users of PHYSICAL_START. They
could be replaced with __pa(_stext).
2) Redefine __va() & __pa() with relocation offset
a) A variable, say relocation_offset (like kernstart_addr), updated
at boot time. This impacts performance, as we have to load an additional
variable from memory.
__va(0x100000) = 0xc0000000 + 0x100000 = 0xc0100000
which is what we want.
I have implemented (3) in the following patch which has same cost of
operation as the existing one.
I have tested the patches on 440x platforms only. However this should
work fine for PPC_47x also, as we only depend on the runtime address
and the current TLB XLAT entry for the startup code, which is available
in r25. I don't have access to a 47x board yet. So, it would be great if
somebody could test this on 47x.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Suzuki Poulose [Wed, 14 Dec 2011 22:58:12 +0000 (22:58 +0000)]
powerpc: Process dynamic relocations for kernel
The following patch implements the dynamic relocation processing for
PPC32 kernel. relocate() accepts the target virtual address and relocates
the kernel image to the same.
Currently the following relocation types are handled :
The last 3 relocations in the above list depends on value of Symbol indexed
whose index is encoded in the Relocation entry. Hence we need the Symbol
Table for processing such relocations.
Note: The GNU ld for ppc32 produces buggy relocations for relocation types
that depend on symbols. The value of the symbols with STB_LOCAL scope
should be assumed to be zero. - Alan Modra
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Signed-off-by: Josh Poimboeuf <jpoimboe@linux.vnet.ibm.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Alan Modra <amodra@au1.ibm.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: linuxppc-dev <linuxppc-dev@lists.ozlabs.org> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Suzuki Poulose [Wed, 14 Dec 2011 22:57:15 +0000 (22:57 +0000)]
powerpc: Rename mapping based RELOCATABLE to DYNAMIC_MEMSTART for BookE
The current implementation of CONFIG_RELOCATABLE in BookE is based
on mapping the page aligned kernel load address to KERNELBASE. This
approach however is not enough for platforms, where the TLB page size
is large (e.g, 256M on 44x). So we are renaming the RELOCATABLE used
currently in BookE to DYNAMIC_MEMSTART to reflect the actual method.
The CONFIG_RELOCATABLE for PPC32(BookE) based on processing of the
dynamic relocations will be introduced in the later in the patch series.
This change would allow the use of the old method of RELOCATABLE for
platforms which can afford to enforce the page alignment (platforms with
smaller TLB size).
Changes since v3:
* Introduced a new config, NONSTATIC_KERNEL, to denote a kernel which is
either a RELOCATABLE or DYNAMIC_MEMSTART(Suggested by: Josh Boyer)
Suggested-by: Scott Wood <scottwood@freescale.com> Tested-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Josh Boyer <jwboyer@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: linux ppc dev <linuxppc-dev@lists.ozlabs.org> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Paul Mackerras [Tue, 13 Dec 2011 17:54:13 +0000 (17:54 +0000)]
powerpc: Only use initrd_end as the limit for alloc_bottom if it's inside the RMO.
As the kernels and initrd's get bigger boot-loaders and possibly
kexec-tools will need to place the initrd outside the RMO. When this
happens we end up with no lowmem and the boot doesn't get very far.
Only use initrd_end as the limit for alloc_bottom if it's inside the
RMO.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Andreas Schwab [Fri, 9 Dec 2011 11:35:08 +0000 (11:35 +0000)]
powerpc: Fix wrong divisor in usecs_to_cputime
Commit d57af9b (taskstats: use real microsecond granularity for CPU times)
renamed msecs_to_cputime to usecs_to_cputime, but failed to update all
numbers on the way. This causes nonsensical cpu idle/iowait values to be
displayed in /proc/stat (the only user of usecs_to_cputime so far).
This also renames __cputime_msec_factor to __cputime_usec_factor, adapting
its value and using it directly in cputime_to_usecs instead of doing two
multiplications.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org> Acked-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
David Rientjes [Thu, 8 Dec 2011 12:46:37 +0000 (12:46 +0000)]
powerpc/mm: Fix section mismatch for read_n_cells
read_n_cells() cannot be marked as .devinit.text since it is referenced
from two functions that are not in that section: of_get_lmb_size() and
hot_add_drconf_scn_to_nid().
Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
David Rientjes [Thu, 8 Dec 2011 12:33:29 +0000 (12:33 +0000)]
powerpc/mm: Fix section mismatch for mark_reserved_regions_for_nid
mark_reserved_regions_for_nid() is only called from do_init_bootmem(),
which is in .init.text, so it must be in the same section to avoid a
section mismatch warning.
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com> Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Matt Evans [Wed, 7 Dec 2011 20:57:09 +0000 (20:57 +0000)]
powerpc: Add __SANE_USERSPACE_TYPES__ to asm/types.h for LL64
PPC64 uses long long for u64 in the kernel, but powerpc's asm/types.h
prevents 64-bit userland from seeing this definition, instead defaulting
to u64 == long in userspace. Some user programs (e.g. kvmtool) may actually
want LL64, so this patch adds a check for __SANE_USERSPACE_TYPES__ so that,
if defined, int-ll64.h is included instead.
Signed-off-by: Matt Evans <matt@ozlabs.org> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 7 Dec 2011 20:11:45 +0000 (20:11 +0000)]
powerpc: POWER7 optimised copy_to_user/copy_from_user using VMX
Implement a POWER7 optimised copy_to_user/copy_from_user using VMX.
For large aligned copies this new loop is over 10% faster, and for
large unaligned copies it is over 200% faster.
If we take a fault we fall back to the old version, this keeps
things relatively simple and easy to verify.
On POWER7 unaligned stores rarely slow down - they only flush when
a store crosses a 4KB page boundary. Furthermore this flush is
handled completely in hardware and should be 20-30 cycles.
Unaligned loads on the other hand flush much more often - whenever
crossing a 128 byte cache line, or a 32 byte sector if either sector
is an L1 miss.
Considering this information we really want to get the loads aligned
and not worry about the alignment of the stores. Microbenchmarks
confirm that this approach is much faster than the current unaligned
copy loop that uses shifts and rotates to ensure both loads and
stores are aligned.
We also want to try and do the stores in cacheline aligned, cacheline
sized chunks. If the store queue is unable to merge an entire
cacheline of stores then the L2 cache will have to do a
read/modify/write. Even worse, we will serialise this with the stores
in the next iteration of the copy loop since both iterations hit
the same cacheline.
Based on this, the new loop does the following things:
1 - 127 bytes
Get the source 8 byte aligned and use 8 byte loads and stores. Pretty
boring and similar to how the current loop works.
128 - 4095 bytes
Get the source 8 byte aligned and use 8 byte loads and stores,
1 cacheline at a time. We aren't doing the stores in cacheline
aligned chunks so we will potentially serialise once per cacheline.
Even so it is much better than the loop we have today.
4096 - bytes
If both source and destination have the same alignment get them both
16 byte aligned, then get the destination cacheline aligned. Do
cacheline sized loads and stores using VMX.
If source and destination do not have the same alignment, we get the
destination cacheline aligned, and use permute to do aligned loads.
In both cases the VMX loop should be optimal - we always do aligned
loads and stores and are always doing stores in cacheline aligned,
cacheline sized chunks.
To be able to use VMX we must be careful about interrupts and
sleeping. We don't use the VMX loop when in an interrupt (which should
be rare anyway) and we wrap the VMX loop in disable/enable_pagefault
and fall back to the existing copy_tofrom_user loop if we do need to
sleep.
The VMX breakpoint of 4096 bytes was chosen using this microbenchmark:
http://ozlabs.org/~anton/junkcode/copy_to_user.c
Since we are using VMX and there is a cost to saving and restoring
the user VMX state there are two broad cases we need to benchmark:
- Best case - userspace never uses VMX
- Worst case - userspace always uses VMX
In reality a userspace process will sit somewhere between these two
extremes. Since we need to test both aligned and unaligned copies we
end up with 4 combinations. The point at which the VMX loop begins to
win is:
0% VMX
aligned 2048 bytes
unaligned 2048 bytes
100% VMX
aligned 16384 bytes
unaligned 8192 bytes
Considering this is a microbenchmark, the data is hot in cache and
the VMX loop has better store queue merging properties we set the
breakpoint to 4096 bytes, a little below the unaligned breakpoints.
Some future optimisations we can look at:
- Looking at the perf data, a significant part of the cost when a
task is always using VMX is the extra exception we take to restore
the VMX state. As such we should do something similar to the x86
optimisation that restores FPU state for heavy users. ie:
/*
* If the task has used fpu the last 5 timeslices, just do a full
* restore of the math state immediately to avoid the trap; the
* chances of needing FPU soon are obviously high now
*/
preload_fpu = tsk_used_math(next_p) && next_p->fpu_counter > 5;
and
/*
* fpu_counter contains the number of consecutive context switches
* that the FPU is used. If this is over a threshold, the lazy fpu
* saving becomes unlazy to save the trap. This is an unsigned char
* so that after 256 times the counter wraps and the behavior turns
* lazy again; this to deal with bursty apps that only use FPU for
* a short time
*/
- We could create a paca bit to mirror the VMX enabled MSR bit and check
that first, avoiding multiple calls to calling enable_kernel_altivec.
That should help with iovec based system calls like readv.
- We could have two VMX breakpoints, one for when we know the user VMX
state is loaded into the registers and one when it isn't. This could
be a second bit in the paca so we can calculate the break points quickly.
- One suggestion from Ben was to save and restore the VSX registers
we use inline instead of using enable_kernel_altivec.
[BenH: Fixed a problem with preempt and fixed build without CONFIG_ALTIVEC]
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc/pmac: Simplify old pmac PIC interrupt handling
In the old days, we treated all interrupts from the legacy Apple home made
interrupt controllers as level, with a trick reading the "level" register
along with the "event" register to work arounds bugs where it would
occasionally fail to latch some events.
Doing so appeared to work fine for both level and edge interrupts.
Later on, we discovered in Darwin source the magic masks that define which
interrupts are actually level and which are edge, and implemented a
different algorithm, more similar to what Apple does, that treats those
differently.
I recently discovered however that this caused problems (including loss
of interrupts) with an old Wallstreet PowerBook when trying to use the
internal modem (connected to a cascaded controller).
It looks like some interrupts are treated as edge while they are really
level and I'm starting to seriously doubt the correctness of the Darwin
code (which has other obvious bugs when you read it, so ...)
This patch reverts to our original behaviour of treating everything as
a level interrupt. It appears to solve the problems with the modem on
the Wallstreet and everything else seems to be working properly as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch reworks & simplifies pmac_zilog handling of suspend/resume,
essentially removing all the specific code in there and using the
generic uart helpers.
This required properly registering the tty as a child of the macio (or platform)
device, so I had to delay the registration a bit (we used to register the ports
very very early). We still register the kernel console early though.
I removed a couple of unused or useless flags as well, relying on the
core to not call us when asleep. I also removed the essentially useless
interrupt mutex, simplifying the locking a bit.
I removed some code for handling unexpected interrupt which should never
be hit and could potentially be harmful (causing us to access a register
on a powered off SCC). We diable port interrupts on close always so there
should be no need to drain data on a closed port.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tony Breeds [Wed, 30 Nov 2011 21:39:21 +0000 (21:39 +0000)]
powerpc/boot: Add extended precision shifts to the boot wrapper.
The upcomming currituck patches will need to do 64-bit shifts which will
fail with undefined symbol without this patch.
I looked at linking against libgcc but we can't guarantee that libgcc
was compiled with soft-float. Also Using ../lib/div64.S or
../kernel/misc_32.S, this will break the build as the .o's need to be
built with different flags for the bootwrapper vs the kernel. So for
now the easyest option is to just copy code from
arch/powerpc/kernel/misc_32.S I don't think this code changes too often ;P
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Tony Breeds [Wed, 30 Nov 2011 21:39:18 +0000 (21:39 +0000)]
powerpc/44x: pci: Add a want_sdr flag into ppc4xx_pciex_hwops
Currituck doesn't need nor use SDR so aborting the pci setup if there is
no sdr-base would be bad.
Add a flag to ppc4xx_pciex_hwops for the backends to state if they need
SDR and then only complain and abort if they do and it's not found in
the device tree.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
Anton Blanchard [Wed, 30 Nov 2011 15:46:45 +0000 (15:46 +0000)]
powerpc/nvram: Add spinlock to oops_to_nvram to prevent oops in compression code.
When issuing a system reset we almost always oops in the oops_to_nvram
code because multiple CPUs are using the deflate work area. Add a
spinlock to protect it.
To play it safe I'm using trylock to avoid locking up if the NVRAM
code oopses. This means we might miss multiple CPUs oopsing at exactly
the same time but I think it's best to play it safe for now. Once we
are happy with the reliability we can change it to a full spinlock.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Jim Keniston <jkenisto@us.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Finn Thain [Tue, 6 Dec 2011 17:49:36 +0000 (17:49 +0000)]
pmac_zilog: Fix unexpected irq
On most 68k Macs the SCC IRQ is an autovector interrupt and cannot be
masked. This can be a problem when pmac_zilog starts up.
For example, the serial debugging code in arch/m68k/kernel/head.S may be
used beforehand. It disables the SCC interrupts at the chip but doesn't
ack them. Then when a pmac_zilog port is used, the machine locks up with
"unexpected interrupt".
This can happen in pmz_shutdown() since the irq is freed before the
channel interrupts are disabled.
Fix this by clearing interrupt enable bits before the handler is
uninstalled. Also move the interrupt control bit flipping into a separate
pmz_interrupt_control() routine. Replace all instances of these operations
with calls to this routine. Omit the zssync() calls that seem to serve no
purpose.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Mon, 5 Dec 2011 19:47:26 +0000 (19:47 +0000)]
powerpc: Provide a way for KVM to indicate that NV GPR values are lost
This fixes a problem where a CPU thread coming out of nap mode can
think it has valid values in the nonvolatile GPRs (r14 - r31) as saved
away in power7_idle, but in fact the values have been trashed because
the thread was used for KVM in the mean time. The result is that the
thread crashes because code that called power7_idle (e.g.,
pnv_smp_cpu_kill_self()) goes to use values in registers that have
been trashed.
The bit field in SRR1 that tells whether state was lost only reflects
the most recent nap, which may not have been the nap instruction in
power7_idle. So we need an extra PACA field to indicate that state
has been lost even if SRR1 indicates that the most recent nap didn't
lose state. We clear this field when saving the state in power7_idle,
we set it to a non-zero value when we use the thread for KVM, and we
test it in power7_wakeup_noloss.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Paul Mackerras [Mon, 5 Dec 2011 19:35:32 +0000 (19:35 +0000)]
powerpc/powernv: Fix problems in onlining CPUs
At present, on the powernv platform, if you off-line a CPU that was
online, and then try to on-line it again, the kernel generates a
warning message "OPAL Error -1 starting CPU n". Furthermore, if the
CPU is a secondary thread that was used by KVM while it was off-line,
the CPU fails to come online.
The first problem is fixed by only calling OPAL to start the CPU the
first time it is on-lined, as indicated by the cpu_start field of its
PACA being zero. The second problem is fixed by restoring the
cpu_start field to 1 instead of 0 when using the CPU within KVM.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Sun, 4 Dec 2011 13:13:58 +0000 (13:13 +0000)]
powerpc/pseries: Increase minimum RMO size from 64MB to 256MB
The minimum RMO size field in ibm,client-architecture is currently
ignored, but a future firmware version will rectify that. Since we
always get at least 128MB of RMO right now, asking for 64MB is
likely to result in boot failures.
We should bump it to at least 128MB, but considering all the boot
issues we have on 128MB RMO boxes and all new machines have virtual
RMO, we may as well set our minimum to 256MB.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With CONFIG_STRICT_DEVMEM=y, user space cannot read any part of /dev/mem.
Since this breaks librtas, punch a hole in /dev/mem to allow access to the
rmo_buffer that librtas needs.
Anton Blanchard reported the problem and helped with the fix.
# dd if=/dev/mem of=/tmp/foo count=1 bs=64k skip=3865
1+0 records in
1+0 records out
65536 bytes (66 kB) copied, 0.000205235 s, 319 MB/s
# dd if=/dev/mem of=/tmp/foo
dd: reading `/dev/mem': Operation not permitted
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.00022519 s, 0.0 kB/s
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So I've had one of these for a while and it looks like the vendor never
bothered submitting the support upstream.
This adds it using ppc40x_simple and provides a device-tree.
There are some changes to the boot wrapper because the way u-boot works
on this thing, it seems to expect a multipart image with the kernel,
initrd and dtb in it.
The USB support is missing as it needs the yet unmerged driver for
the DWC OTG part and the GPIOs may need further definition in the dts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Geoff Levand [Tue, 29 Nov 2011 15:38:49 +0000 (15:38 +0000)]
powerpc/ps3: Interrupt code cleanup
General code cleanup for PS3 interrupt.c:
o Fill out comments for structure members.
o Move variables ipi_debug_brk_mask and lock from struct ps3_bmp to
struct ps3_private.
o Fix pr_debug build errors when DEBUG is defined.
o Convert bit operation to set_bit().
o Convert DBG macro from pr_debug to pr_devel
o Add new macro FAIL to replace pr_debug calls
Signed-off-by: Geoff Levand <geoff@infradead.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:17 +0000 (00:23 +0000)]
powerpc/kdump: Only save CPU state first time through the secondary CPU capture code
We might enter the secondary CPU capture code twice, eg if we have to
unstick some CPUs with a system reset. In this case we don't want to
overwrite the state on CPUs that had made it into the capture code OK,
so use the cpus_state_saved cpumask for that and make it local to
crash_ipi_callback.
For controlling progress now use atomic_t cpus_in_crash to count how
many CPUs have made it into the kdump code, and time_to_dump to tell
everyone it's time to dump.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:16 +0000 (00:23 +0000)]
powerpc/kdump: Delay before sending IPI on a system reset
If we enter the kdump code via system reset, wait a bit before
sending the IPI to capture all secondary CPUs. Without it we race
with the hypervisor that is issuing the system reset to each CPU.
If the IPI gets there first the system reset oops output then shows
the register state of the IPI handler which is not what we want.
I took the opportunity to add defines for all the various delays
we have. There's no need for cpu_relax when we are doing an mdelay,
so remove them too.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:14 +0000 (00:23 +0000)]
powerpc: Reduce pseries panic timeout from 180s to 10s
We've had a 180 second panic timeout on ppc64 for as long as I
can remember. This patch reduces it to 10 seconds on pseries for a few
reasons:
- Almost all pseries machines have a hypervisor console so panic
output will be available in a scrollback buffer.
- The 180 seconds impacts our availability, users (other than
kernel hackers) just want the box to come back around so it
can continue its work.
- I spend a lot of my life staring at the 180 second panic timeout.
Many pseries machines take minutes to power cycle, so it's quicker
to sit through the 180 seconds than it is to power cycle.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:11 +0000 (00:23 +0000)]
powerpc/kdump: Use setjmp/longjmp to handle kdump and system reset recursion
We can handle recursion caused by system reset by reusing the crash
shutdown fault handler.
Since we don't have an OS triggerable NMI, if all CPUs don't make it
into kdump then we tell the user to issue a system reset. However if
we have a panic timeout set we cannot wait forever and must continue
the kdump.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:10 +0000 (00:23 +0000)]
powerpc: Remove broken and complicated kdump system reset code
We have a lot of complicated logic that handles possible recursion between
kdump and a system reset exception. We can solve this in a much simpler
way using the same setjmp/longjmp tricks xmon does.
As a first step, this patch removes the old system reset code.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Anton Blanchard [Wed, 30 Nov 2011 00:23:09 +0000 (00:23 +0000)]
powerpc: Give us time to get all oopses out before panicking
I've been seeing truncated output when people send system reset info
to me. We should see a backtrace for every CPU, but the panic() code
takes the box down before they all make it out to the console. The
panic code runs unlocked so we also see corrupted console output.
If we are going to panic, then delay 1 second before calling into the
panic code. Move oops_exit inside the die lock and put a newline
between oopses for clarity.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Deepthi Dharwar [Wed, 30 Nov 2011 02:47:03 +0000 (02:47 +0000)]
powerpc/cpuidle: Handle power_save=off
This patch makes pseries_idle_driver not to be registered when
power_save=off kernel boot option is specified. The
cpuidle_disable variable used here is similar to
its usage on x86. If cpuidle_disable is set then
sysfs entries for cpuidle framework are not created
and the required drivers are not loaded.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com> Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Deepthi Dharwar [Wed, 30 Nov 2011 02:46:55 +0000 (02:46 +0000)]
powerpc/cpuidle: Enable cpuidle and directly call cpuidle_idle_call() for pSeries
This patch enables cpuidle for pSeries and pSeries_idle is
directly called from the idle loop. As a result of pSeries_idle, cpuidle
driver registered with cpuidle subsystem comes into action. On
failure of loading of the driver or cpuidle framework default idle
is executed as part of the function. This patch
also removes the routines pseries_shared_idle_sleep and
pseries_dedicated_idle_sleep as they are now implemented as part of
pseries_idle cpuidle driver.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com> Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Deepthi Dharwar [Wed, 30 Nov 2011 02:46:42 +0000 (02:46 +0000)]
powerpc/cpuidle: cpuidle driver for pSeries
This patch implements a back-end cpuidle driver for pSeries
based on pseries_dedicated_idle_loop and pseries_shared_idle_loop
routines. The driver is built only if CONFIG_CPU_IDLE is set. This
cpuidle driver uses global registration of idle states and
not per-cpu.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com> Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Deepthi Dharwar [Wed, 30 Nov 2011 02:46:31 +0000 (02:46 +0000)]
powerpc/cpuidle: Add cpu_idle_wait() to allow switching of idle routines
This patch provides cpu_idle_wait() routine for the powerpc
platform which is required by the cpuidle subsystem. This
routine is required to change the idle handler on SMP systems.
The equivalent routine for x86 is in arch/x86/kernel/process.c
but the powerpc implementation is different.
cpuidle_disable variable is to enable/disable cpuidle
framework if power_save option is set during the boot
time.
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com> Signed-off-by: Trinabh Gupta <g.trinabh@gmail.com> Signed-off-by: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:43 +0000 (10:50 +0000)]
powerpc: Add gpages reservation code for 64-bit FSL BOOKE
For 64-bit FSL_BOOKE implementations, gigantic pages need to be
reserved at boot time by the memblock code based on the command line.
This adds the call that handles the reservation, and fixes some code
comments.
It also removes the previous pr_err when reserve_hugetlb_gpages
is called on a system without hugetlb enabled - the way the code is
structured, the call is unconditional and the resulting error message
spurious and confusing.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:42 +0000 (10:50 +0000)]
powerpc: Add hugepage support to 64-bit tablewalk code for FSL_BOOK3E
Before hugetlb, at each level of the table, we test for
!0 to determine if we have a valid table entry. With hugetlb, this
compare becomes:
< 0 is a normal entry
0 is an invalid entry
> 0 is huge
This works because the hugepage code pulls the top bit off the entry
(which for non-huge entries always has the top bit set) as an
indicator that we have a hugepage.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:41 +0000 (10:50 +0000)]
powerpc: Whitespace/comment changes to tlb_low_64e.S
I happened to comment this code while I was digging through it;
we might as well commit that. I also made some whitespace
changes - the existing code had a lot of unnecessary newlines
that I found annoying when I was working on my tiny laptop.
No functional changes.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:40 +0000 (10:50 +0000)]
powerpc: hugetlb: modify include usage for FSL BookE code
The original 32-bit hugetlb implementation used PPC64 vs PPC32 to
determine which code path to take. However, the final hugetlb
implementation for 64-bit FSL ended up shared with the FSL
32-bit code so the actual check needs to be FSL_BOOK3E vs
everything else. This patch changes the include protections to
reflect this.
There are also a couple of related comment fixes.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:39 +0000 (10:50 +0000)]
powerpc: Update hugetlb huge_pte_alloc and tablewalk code for FSL BOOKE
This updates the hugetlb page table code to handle 64-bit FSL_BOOKE.
The previous 32-bit work counted on the inner levels of the page table
collapsing.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:38 +0000 (10:50 +0000)]
powerpc: Fix booke hugetlb preload code for PPC_MM_SLICES and 64-bit
This patch does 2 things: It corrects the code that determines the
size to write into MAS1 for the PPC_MM_SLICES case (this originally
came from David Gibson and I had incorrectly altered it), and it
changes the methodolody used to calculate the size for !PPC_MM_SLICES
to work for 64-bit as well as 32-bit.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Becky Bruce [Mon, 10 Oct 2011 10:50:37 +0000 (10:50 +0000)]
powerpc: hugetlb: fix huge_ptep_set_access_flags return value
There was an unconditional return of "1" in the original code
from David Gibson, and I dropped it because it wasn't needed
for FSL BOOKE 32-bit. However, not all systems (including 64-bit
FSL BOOKE) do loading of the hpte from the fault handler asm
and depend on this function returning 1, which causes a call
to update_mmu_cache() that writes an entry into the tlb.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:07 +0000 (06:28 +0000)]
powerpc/mpic: Add in-core support for cascaded MPICs
The Cell and PowerMac platforms use virtually identical cascaded-IRQ
setup code, so just merge it into the core. Ideally this code would
trigger automatically when an MPIC device-node specifies an "interrupts"
property, perhaps even enabling MPIC_SECONDARY along the way.
Unfortunately, Benjamin Herrenschmidt has had bad experiences in the
past with the quality of Apple PowerMac device-trees, so to be safe we
will only try to parse out an IRQ if the MPIC_SECONDARY flag is set by
the caller.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:05 +0000 (06:28 +0000)]
powerpc/mpic: Put "pic-no-reset" test back into the MPIC code
There's not really any reason to have this one-liner in a separate
static inline function, given that all the other similar tests are
already in the alloc_mpic() code.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:03 +0000 (06:28 +0000)]
powerpc/mpic: Invert the meaning of MPIC_PRIMARY
It turns out that there are only 2 in-tree platforms which use MPICs
which are not "primary": IBM Cell and PowerMac. To reduce the
complexity of the typical board setup code, invert the MPIC_PRIMARY bit
into MPIC_SECONDARY.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:02 +0000 (06:28 +0000)]
powerpc/mpic: Search for open-pic device-tree node if NULL
Almost all PowerPC platforms use a standard "open-pic" device node so
the mpic_alloc() function now accepts NULL for the device-node. This
will cause it to perform a default search with of_find_matching_node().
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Kyle Moffett [Fri, 2 Dec 2011 06:28:01 +0000 (06:28 +0000)]
powerpc/mpic: Save computed phys_addr for board-specific code
The MPIC code can already perform an automatic OF address translation
step as part of mpic_alloc(), but several boards need to use that base
address when they perform mpic_assign_isu().
The easiest solution is to save the computed physical address into the
"struct mpic" for later use by the board code.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>