David S. Miller [Mon, 16 May 2016 17:59:20 +0000 (13:59 -0400)]
Merge branch 'qed-next'
Yuval Mintz says:
====================
qed: IOV enhncements and fixups
This is a follow-up on the recent patch series that adds SR-IOV support
to qed. All content here is iov-related fixups [nothing terminal] and
enhancements.
Please consider applying this series to `net-next'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 15 May 2016 11:48:08 +0000 (14:48 +0300)]
qed: Allow more than 16 VFs
In multi-function modes, PFs are currently limited to using 16 VFs -
But that limitation would also currently apply in case there's a single
PCI function exposed, where no such restriction should have existed.
This lifts the restriction for the default mode; User should be able
to start the maximum number of VFs as appear in the PCI config space.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra [Sun, 15 May 2016 11:48:07 +0000 (14:48 +0300)]
qed: Reset link on IOV disable
PF updates its VFs' bulletin boards with link configurations whenever
the physical carrier changes or whenever hyper-user explicitly requires
some setting of the VFs link via the hypervisor's PF.
Since the bulletin board is getting cleaned as part of the IOV disable
flow on the PF side, re-enabling sriov would lead to a VF that sees the
carrier as 'down', until an event causing the PF to re-fill the bulletin
with the link configuration would occur.
To fix this we simply refelect the link state during the flows, giving
the later VFs a default reflecting the PFs link state.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 15 May 2016 11:48:06 +0000 (14:48 +0300)]
qed: Improve VF interrupt reset
During FLR flow, need to make sure HW is no longer capable of writing to
host memory as part of its interrupt mechanisms.
While we're at it, unify the logic cleaning the driver's status-blocks
into using a single API function for both PFs and VFs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Sun, 15 May 2016 07:21:26 +0000 (10:21 +0300)]
net/mlx4_core: Fix access to uninitialized index
Prevent using uninitialized or negative index when handling
steering entries.
Fixes: b12d93d63c32 ('mlx4: Add support for promiscuous mode in the new steering model.') Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here are two more Bluetooth patches for the 4.7 kernel which we wanted
to get into net-next before the merge window opens. Please let me know
if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 May 2016 17:55:49 +0000 (13:55 -0400)]
Merge branch 'w5100-small-changes'
Akinobu Mita says:
====================
net: w5100: collection of small changes
This patch series is the collection of relatively small changes for
w5100 driver which includes a cleanup with no functional change,
two fixes, and adding a functionality.
* Changes from v1
- Remove the watchdong_timeo assignment to set default tx timeout,
suggested by David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Sat, 14 May 2016 05:55:50 +0000 (14:55 +0900)]
net: w5100-spi: add support to specify MAC address by device tree
This adds support to specify the MAC address by 'mac-address' or
'local-mac-address' properties in the device tree. These are common
properties for the Ethernet controller.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Sat, 14 May 2016 05:55:49 +0000 (14:55 +0900)]
net: w5100: increase TX timeout period
This increases TX timeout period from one second to 5 seconds which is
the default value if the driver doesn't explicitly set
net_device->watchdog_timeo.
The one second timeout is too short for W5100 with SPI interface mode
which doesn't support burst READ/WRITE processing in the SPI transfer.
If the packet is transmitted while RX packets are being received at a
very high rate, the TX transmittion work in the workqueue is delayed
and the watchdog timer is expired.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Sat, 14 May 2016 05:55:48 +0000 (14:55 +0900)]
net: w5100: fix MAC filtering for W5500
W5500 has different bit position for MAC filter in Socket n mode
register from W5100 and W5200.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Sat, 14 May 2016 05:55:47 +0000 (14:55 +0900)]
net: w5100: remove unused is_w5200()
The is_w5200() function is not used anymore by the commit which adds
the W5500 support.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 May 2016 17:49:33 +0000 (13:49 -0400)]
Merge branch 'bpf-blinding'
Daniel Borkmann says:
====================
BPF updates
This set implements constant blinding for BPF, first couple of
patches are some preparatory cleanups, followed by the blinding.
Please see individual patches for details.
Thanks a lot!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 13 May 2016 17:08:35 +0000 (19:08 +0200)]
bpf, s390: add support for constant blinding
This patch adds recently added constant blinding helpers into the
s390 eBPF JIT. In the bpf_int_jit_compile() path, requirements are
to utilize bpf_jit_blind_constants()/bpf_jit_prog_release_other()
pair for rewriting the program into a blinded one, and to map the
BPF_REG_AX register to a CPU register. The mapping of BPF_REG_AX
is at r12 and similarly like in x86 case performs reloading when
ld_abs/ind is used. When blinding is not used, there's no additional
overhead in the generated image.
When BPF_REG_AX is used, we don't need to emit skb->data reload when
helper function changed skb->data, as this will be reloaded later
on anyway from stack on ld_abs/ind, where skb->data is needed. s390
allows for this w/o much additional complexity unlike f.e. x86.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 13 May 2016 17:08:34 +0000 (19:08 +0200)]
bpf, arm64: add support for constant blinding
This patch adds recently added constant blinding helpers into the
arm64 eBPF JIT. In the bpf_int_jit_compile() path, requirements are
to utilize bpf_jit_blind_constants()/bpf_jit_prog_release_other()
pair for rewriting the program into a blinded one, and to map the
BPF_REG_AX register to a CPU register. The mapping is on x9.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Zi Shen Lim <zlim.lnx@gmail.com> Acked-by: Yang Shi <yang.shi@linaro.org> Tested-by: Yang Shi <yang.shi@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 13 May 2016 17:08:33 +0000 (19:08 +0200)]
bpf, x86: add support for constant blinding
This patch adds recently added constant blinding helpers into the
x86 eBPF JIT. In the bpf_int_jit_compile() path, requirements are
to utilize bpf_jit_blind_constants()/bpf_jit_prog_release_other()
pair for rewriting the program into a blinded one, and to map the
BPF_REG_AX register to a CPU register. The mapping of BPF_REG_AX
is at non-callee saved register r10, and thus shared with cached
skb->data used for ld_abs/ind and not in every program type needed.
When blinding is not used, there's zero additional overhead in the
generated image.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 13 May 2016 17:08:32 +0000 (19:08 +0200)]
bpf: add generic constant blinding for use in jits
This work adds a generic facility for use from eBPF JIT compilers
that allows for further hardening of JIT generated images through
blinding constants. In response to the original work on BPF JIT
spraying published by Keegan McAllister [1], most BPF JITs were
changed to make images read-only and start at a randomized offset
in the page, where the rest was filled with trap instructions. We
have this nowadays in x86, arm, arm64 and s390 JIT compilers.
Additionally, later work also made eBPF interpreter images read
only for kernels supporting DEBUG_SET_MODULE_RONX, that is, x86,
arm, arm64 and s390 archs as well currently. This is done by
default for mentioned JITs when JITing is enabled. Furthermore,
we had a generic and configurable constant blinding facility on our
todo for quite some time now to further make spraying harder, and
first implementation since around netconf 2016.
We found that for systems where untrusted users can load cBPF/eBPF
code where JIT is enabled, start offset randomization helps a bit
to make jumps into crafted payload harder, but in case where larger
programs that cross page boundary are injected, we again have some
part of the program opcodes at a page start offset. With improved
guessing and more reliable payload injection, chances can increase
to jump into such payload. Elena Reshetova recently wrote a test
case for it [2, 3]. Moreover, eBPF comes with 64 bit constants, which
can leave some more room for payloads. Note that for all this,
additional bugs in the kernel are still required to make the jump
(and of course to guess right, to not jump into a trap) and naturally
the JIT must be enabled, which is disabled by default.
For helping mitigation, the general idea is to provide an option
bpf_jit_harden that admins can tweak along with bpf_jit_enable, so
that for cases where JIT should be enabled for performance reasons,
the generated image can be further hardened with blinding constants
for unpriviledged users (bpf_jit_harden == 1), with trading off
performance for these, but not for privileged ones. We also added
the option of blinding for all users (bpf_jit_harden == 2), which
is quite helpful for testing f.e. with test_bpf.ko. There are no
further e.g. hardening levels of bpf_jit_harden switch intended,
rationale is to have it dead simple to use as on/off. Since this
functionality would need to be duplicated over and over for JIT
compilers to use, which are already complex enough, we provide a
generic eBPF byte-code level based blinding implementation, which is
then just transparently JITed. JIT compilers need to make only a few
changes to integrate this facility and can be migrated one by one.
This option is for eBPF JITs and will be used in x86, arm64, s390
without too much effort, and soon ppc64 JITs, thus that native eBPF
can be blinded as well as cBPF to eBPF migrations, so that both can
be covered with a single implementation. The rule for JITs is that
bpf_jit_blind_constants() must be called from bpf_int_jit_compile(),
and in case blinding is disabled, we follow normally with JITing the
passed program. In case blinding is enabled and we fail during the
process of blinding itself, we must return with the interpreter.
Similarly, in case the JITing process after the blinding failed, we
return normally to the interpreter with the non-blinded code. Meaning,
interpreter doesn't change in any way and operates on eBPF code as
usual. For doing this pre-JIT blinding step, we need to make use of
a helper/auxiliary register, here BPF_REG_AX. This is strictly internal
to the JIT and not in any way part of the eBPF architecture. Just like
in the same way as JITs internally make use of some helper registers
when emitting code, only that here the helper register is one
abstraction level higher in eBPF bytecode, but nevertheless in JIT
phase. That helper register is needed since f.e. manually written
program can issue loads to all registers of eBPF architecture.
The core concept with the additional register is: blind out all 32
and 64 bit constants by converting BPF_K based instructions into a
small sequence from K_VAL into ((RND ^ K_VAL) ^ RND). Therefore, this
is transformed into: BPF_REG_AX := (RND ^ K_VAL), BPF_REG_AX ^= RND,
and REG <OP> BPF_REG_AX, so actual operation on the target register
is translated from BPF_K into BPF_X one that is operating on
BPF_REG_AX's content. During rewriting phase when blinding, RND is
newly generated via prandom_u32() for each processed instruction.
64 bit loads are split into two 32 bit loads to make translation and
patching not too complex. Only basic thing required by JITs is to
call the helper bpf_jit_blind_constants()/bpf_jit_prog_release_other()
pair, and to map BPF_REG_AX into an unused register.
Small bpf_jit_disasm extract from [2] when applied to x86 JIT:
As can be seen, original constants that carry payload are hidden
when enabled, actual operations are transformed from constant-based
to register-based ones, making jumps into constants ineffective.
Above extract/example uses single BPF load instruction over and
over, but of course all instructions with constants are blinded.
Performance wise, JIT with blinding performs a bit slower than just
JIT and faster than interpreter case. This is expected, since we
still get all the performance benefits from JITing and in normal
use-cases not every single instruction needs to be blinded. Summing
up all 296 test cases averaged over multiple runs from test_bpf.ko
suite, interpreter was 55% slower than JIT only and JIT with blinding
was 8% slower than JIT only. Since there are also some extremes in
the test suite, I expect for ordinary workloads that the performance
for the JIT with blinding case is even closer to JIT only case,
f.e. nmap test case from suite has averaged timings in ns 29 (JIT),
35 (+ blinding), and 151 (interpreter).
BPF test suite, seccomp test suite, eBPF sample code and various
bigger networking eBPF programs have been tested with this and were
running fine. For testing purposes, I also adapted interpreter and
redirected blinded eBPF image to interpreter and also here all tests
pass.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Elena Reshetova <elena.reshetova@intel.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Since the blinding is strictly only called from inside eBPF JITs,
we need to change signatures for bpf_int_jit_compile() and
bpf_prog_select_runtime() first in order to prepare that the
eBPF program we're dealing with can change underneath. Hence,
for call sites, we need to return the latest prog. No functional
change in this patch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 13 May 2016 17:08:30 +0000 (19:08 +0200)]
bpf: add bpf_patch_insn_single helper
Move the functionality to patch instructions out of the verifier
code and into the core as the new bpf_patch_insn_single() helper
will be needed later on for blinding as well. No changes in
functionality.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 13 May 2016 17:08:29 +0000 (19:08 +0200)]
bpf, x86/arm64: remove useless checks on prog
There is never such a situation, where bpf_int_jit_compile() is
called with either prog as NULL or len as 0, so the tests are
unnecessary and confusing as people would just copy them. s390
doesn't have them, so no change is needed there.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Later code also needs this facility to check for eBPF JITs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 13 May 2016 17:08:27 +0000 (19:08 +0200)]
bpf: move bpf_jit_enable declaration
Move the bpf_jit_enable declaration to the filter.h file where
most other core code is declared, also since we're going to add
a second knob there.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 13 May 2016 17:08:26 +0000 (19:08 +0200)]
bpf: minor cleanups in ebpf code
Besides others, remove redundant comments where the code is self
documenting enough, and properly indent various bpf_verifier_ops
and bpf_prog_type_list declarations. Moreover, remove two exports
that actually have no module user.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 14 May 2016 00:38:23 +0000 (20:38 -0400)]
net: dsa: mv88e6xxx: remove bridge work
Now that the bridge code defers the switchdev port state setting, there
is no need to defer the port STP state change within the mv88e6xxx code.
Thus get rid of the driver's bridge work code.
This also fixes a race condition where the DSA layer assumes that the
bridge code already set the unbridged port's STP state to Disabled
before restoring the Forwarding state.
As a consequence, this also fixes the FDB flush for the unbridged port
which now correctly occurs during the Forwarding to Disabled transition.
Fixes: 0bc05d585d38 ("switchdev: allow caller to explicitly request attr_set as deferred") Reported-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Fri, 13 May 2016 19:23:45 +0000 (12:23 -0700)]
net: vrf: protect changes to private data with rcu
One cpu can be processing packets which includes using the cached route
entries in the vrf device's private data and on another cpu the device
gets deleted which releases the routes and sets the pointers in net_vrf
to NULL. This results in datapath dereferencing a NULL pointer.
Fix by protecting access to dst's with rcu.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver") Fixes: 35402e313663 ("net: Add IPv6 support to VRF device") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 13 May 2016 16:16:40 +0000 (09:16 -0700)]
tcp: minor optimizations around tcp_hdr() usage
tcp_hdr() is slightly more expensive than using skb->data in contexts
where we know they point to the same byte.
In receive path, tcp_v4_rcv() and tcp_v6_rcv() are in this situation,
as tcp header has not been pulled yet.
In output path, the same can be said when we just pushed the tcp header
in the skb, in tcp_transmit_skb() and tcp_make_synack()
Also factorize the two checks for tcb->tcp_flags & TCPHDR_SYN in
tcp_transmit_skb() and pass tcp header pointer to tcp_ecn_send(),
so that compiler can further optimize and avoid a reload.
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 13 May 2016 13:14:37 +0000 (06:14 -0700)]
sock: propagate __sock_cmsg_send() error
__sock_cmsg_send() might return different error codes, not only -EINVAL.
Fixes: 24025c465f77 ("ipv4: process socket-level control messages in IPv4") Fixes: ad1e46a83716 ("ipv6: process socket-level control messages in IPv6") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 13 May 2016 13:09:58 +0000 (15:09 +0200)]
net: qrtr: fix build problems
Having multiple loadable modules with the same name cannot work
with modprobe, and having both net/qrtr/smd.ko and drivers/soc/qcom/smd.ko
results in a (somewhat cryptic) build error:
Also, the qrtr driver uses the SMD interface and has a Kconfig dependency,
but also allows for compile-testing when SMD is disabled. However, if
with QCOM_SMD=m and COMPILE_TEST=y we can end up with QRTR_SMD=y and
that fails with a related link error.
The changes the dependency so we can still compile-test the driver but
not have it built-in if SMD is a module, to avoid running in the broken
configuration, and changes the Makefile to provide the driver under
a different module name.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: bdabad3e363d ("net: Add Qualcomm IPC router") Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset introduces counters support for offloaded cls_flower filters.
When the user calls 'tc show -s ..', fl_dump is called.
Before fl_dump() returns the statistics, it calls the NIC driver (using a new
ndo_setup_tc() command - TC_CLSFLOWER_STATS) to read the hardware counters and
update the statistics accordingly. A new TC action op was added (stats_update())
to be used by the NIC driver to update the statistics.
Patchset was applied and tested over commit ed7cbbc ("udp: Resolve NULL pointer
dereference over flow-based vxlan device")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Fri, 13 May 2016 12:55:41 +0000 (12:55 +0000)]
net/mlx5_core: Flow counters infrastructure
If a counter has the aging flag set when created, it is added to a list
of counters that will be queried periodically from a workqueue. query
result and last use timestamp are cached.
add/del counter must be very efficient since thousands of such
operations might be issued in a second.
There is only a single reference to counters without aging, therefore
no need for locks.
But, counters with aging enabled are stored in a list. In order to make
code as lockless as possible, all the list manipulation and access to
hardware is done from a single context - the periodic counters query
thread.
The hardware supports multiple counters per FTE, however currently we
are using one counter for each FTE.
Signed-off-by: Amir Vadai <amirva@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Fri, 13 May 2016 12:55:40 +0000 (12:55 +0000)]
net/mlx5_core: Introduce flow steering destination of type counter
When adding a flow steering rule with a counter, need to supply a
destination of type MLX5_FLOW_DESTINATION_TYPE_COUNTER, with a pointer
to a struct mlx5_fc.
Also, MLX5_FLOW_CONTEXT_ACTION_COUNT bit should be set in the action.
Signed-off-by: Amir Vadai <amirva@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Fri, 13 May 2016 12:55:37 +0000 (12:55 +0000)]
net/sched: cls_flower: Hardware offloaded filters statistics support
Introduce a new command in ndo_setup_tc() for hardware offloaded
filters, to call the NIC driver, and make it update the statistics.
This will be done before dumping the filter and its statistics.
Signed-off-by: Amir Vadai <amirva@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai [Fri, 13 May 2016 12:55:35 +0000 (12:55 +0000)]
net/sched: Enable netdev drivers to update statistics of offloaded actions
Introduce stats_update callback. netdev driver could call it for offloaded
actions to update the basic statistics (packets, bytes and last use).
Since bstats_update() and bstats_cpu_update() use skb as an argument to
get the counters, _bstats_update() and _bstats_cpu_update(), that get
bytes and packets as arguments, were added.
Signed-off-by: Amir Vadai <amirva@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jisheng Zhang [Fri, 13 May 2016 11:57:30 +0000 (19:57 +0800)]
net: pxa168_eth: Use dma_wmb/rmb where appropriate
Update the pxa168_eth driver to use the dma_rmb/wmb calls instead of the
full barriers in order to improve performance: reduced 97ns/39ns on
average in tx/rx path on Marvell BG4CT platform.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 May 2016 17:35:57 +0000 (13:35 -0400)]
Merge branch 'xen-netback-control-ring'
Paul Durrant says:
====================
xen-netback: support for control ring
My recent patch to import an up-to-date include/xen/interface/io/netif.h
from the Xen Project brought in the necessary definitions to support the
new control shared ring and protocol. This patch series updates xen-netback
to support the new ring.
Patch #1 adds the necessary boilerplate to map the control ring and handle
messages. No implementation of the new protocol is included in this patch
so that it can be kept to a reasonable size.
Patch #2 adds the protocol implementation.
Patch #3 adds support for passing has values calculated by xen-netback to
capable frontends.
Patch #4 adds support for accepting hash values calculated by capable
frontends and using them the set the socket buffer hash.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant [Fri, 13 May 2016 08:37:29 +0000 (09:37 +0100)]
xen-netback: use hash value from the frontend
My recent patch to include/xen/interface/io/netif.h defines a new extra
info type that can be used to pass hash values between backend and guest
frontend.
This patch adds code to xen-netback to use the value in a hash extra
info fragment passed from the guest frontend in a transmit-side
(i.e. netback receive side) packet to set the skb hash accordingly.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant [Fri, 13 May 2016 08:37:28 +0000 (09:37 +0100)]
xen-netback: pass hash value to the frontend
My recent patch to include/xen/interface/io/netif.h defines a new extra
info type that can be used to pass hash values between backend and guest
frontend.
This patch adds code to xen-netback to pass hash values calculated for
guest receive-side packets (i.e. netback transmit side) to the frontend.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant [Fri, 13 May 2016 08:37:27 +0000 (09:37 +0100)]
xen-netback: add control protocol implementation
My recent patch to include/xen/interface/io/netif.h defines a new shared
ring (in addition to the rx and tx rings) for passing control messages
from a VM frontend driver to a backend driver.
A previous patch added the necessary boilerplate for mapping the control
ring from the frontend, should it be created. This patch adds
implementations for each of the defined protocol messages.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Durrant [Fri, 13 May 2016 08:37:26 +0000 (09:37 +0100)]
xen-netback: add control ring boilerplate
My recent patch to include/xen/interface/io/netif.h defines a new shared
ring (in addition to the rx and tx rings) for passing control messages
from a VM frontend driver to a backend driver.
This patch adds the necessary code to xen-netback to map this new shared
ring, should it be created by a frontend, but does not add implementations
for any of the defined protocol messages. These are added in a subsequent
patch for clarity.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 May 2016 17:30:57 +0000 (13:30 -0400)]
Merge branch 'cls_u32_hw_sw'
Sridhar Samudrala says:
====================
Enable SW only or HW only offloads with u32 classifier
This set of patches export TCA_CLS_FLAGS_SKIP_HW to userspace and also
introduces another flag TCA_CLS_FLAGS_SKIP_SW. These flags enable offloading
u32 filters to either SW or HW only.
The default semantics with no flags is to add the filter to HW if possible and
also into SW.
With SKIP_HW flag, the filter is only added to SW.
With SKIP_SW flag, the filter is added to HW and an error is returned
to user on failure.
These flags are mutually exclusive.
There was an earlier discussion on these semantics in the following email
thread.
http://thread.gmane.org/gmane.linux.network/401733
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: cls_u32: Add support for skip-sw flag to tc u32 classifier.
On devices that support TC U32 offloads, this flag enables a filter to be
added only to HW. skip-sw and skip-hw are mutually exclusive flags. By
default without any flags, the filter is added to both HW and SW, but no
error checks are done in case of failure to add to HW. With skip-sw,
failure to add to HW is treated as an error.
Here is a sample script that adds 2 filters, one with skip-sw and the other
with skip-hw flag.
# add ingress qdisc
tc qdisc add dev p4p1 ingress
# enable hw tc offload.
ethtool -K p4p1 hw-tc-offload on
# add u32 filter with skip-sw flag.
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:1 u32 ht 800: flowid 800:1 \
skip-sw \
match ip src 192.168.1.0/24 \
action drop
# add u32 filter with skip-hw flag.
tc filter add dev p4p1 parent ffff: protocol ip prio 99 \
handle 800:0:2 u32 ht 800: flowid 800:2 \
skip-hw \
match ip src 192.168.2.0/24 \
action drop
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sched: Move TCA_CLS_FLAGS_SKIP_HW to uapi header file.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Acked-by: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 May 2016 17:26:01 +0000 (13:26 -0400)]
Merge branch 'hv_netvsc-races'
Vitaly Kuznetsov says:
====================
hv_netvsc: avoid races on mtu change/set channels
Changes since v1:
- Rebased to net-next [Haiyang Zhang]
Original description:
MTU change and set channels operations are implemented as netvsc device
re-creation destroying internal structures (struct net_device stays). This
is really unfortunate but there is no support from Hyper-V host to do it
in a different way. Such re-creation is unsurprisingly racy, Haiyang
reported a crash when netvsc_change_mtu() is racing with
netvsc_link_change() but I was able to identify additional races upon
investigation. Both netvsc_set_channels() and netvsc_change_mtu() race
against:
1) netvsc_link_change()
2) netvsc_remove()
3) netvsc_send()
To solve these issues without introducing new locks some refactoring is
required. We need to get rid of very complex link graph in all the
internal structures and avoid traveling through structures which are being
removed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Fri, 13 May 2016 11:55:25 +0000 (13:55 +0200)]
hv_netvsc: set nvdev link after populating chn_table
Crash in netvsc_send() is observed when netvsc device is re-created on
mtu change/set channels. The crash is caused by dereferencing of NULL
channel pointer which comes from chn_table. The root cause is a mixture
of two facts:
- we set nvdev pointer in net_device_context in alloc_net_device()
before we populate chn_table.
- we populate chn_table[0] only.
The issue could be papered over by checking channel != NULL in
netvsc_send() but populating the whole chn_table and writing the
nvdev pointer afterwards seems more appropriate.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Fri, 13 May 2016 11:55:24 +0000 (13:55 +0200)]
hv_netvsc: synchronize netvsc_change_mtu()/netvsc_set_channels() with netvsc_remove()
When netvsc device is removed during mtu change or channels setup we get
into troubles as both paths are trying to remove the device. Synchronize
them with start_remove flag and rtnl lock.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Fri, 13 May 2016 11:55:22 +0000 (13:55 +0200)]
hv_netvsc: untangle the pointer mess
We have the following structures keeping netvsc adapter state:
- struct net_device
- struct net_device_context
- struct netvsc_device
- struct rndis_device
- struct hv_device
and there are pointers/dependencies between them:
- struct net_device_context is contained in struct net_device
- struct hv_device has driver_data pointer which points to
'struct net_device' OR 'struct netvsc_device' depending on driver's
state (!).
- struct net_device_context has a pointer to 'struct hv_device'.
- struct netvsc_device has pointers to 'struct hv_device' and
'struct net_device_context'.
- struct rndis_device has a pointer to 'struct netvsc_device'.
Different functions get different structures as parameters and use these
pointers for traveling. The problem is (in addition to keeping in mind
this complex graph) that some of these structures (struct netvsc_device
and struct rndis_device) are being removed and re-created on mtu change
(as we implement it as re-creation of hyper-v device) so our travel using
these pointers is dangerous.
Simplify this to a the following:
- add struct netvsc_device pointer to struct net_device_context (which is
a part of struct net_device and thus never disappears)
- remove struct hv_device and struct net_device_context pointers from
struct netvsc_device
- replace pointer to 'struct netvsc_device' with pointer to
'struct net_device'.
- always keep 'struct net_device' in hv_device driver_data.
We'll end up with the following 'circular' structure:
Vitaly Kuznetsov [Fri, 13 May 2016 11:55:21 +0000 (13:55 +0200)]
hv_netvsc: use start_remove flag to protect netvsc_link_change()
netvsc_link_change() can race with netvsc_change_mtu() or
netvsc_set_channels() as these functions destroy struct netvsc_device and
rndis filter. Use start_remove flag for syncronization. As
netvsc_change_mtu()/netvsc_set_channels() are called with rtnl lock held
we need to take it before checking start_remove value in
netvsc_link_change().
Reported-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaly Kuznetsov [Fri, 13 May 2016 11:55:20 +0000 (13:55 +0200)]
hv_netvsc: move start_remove flag to net_device_context
struct netvsc_device is destroyed on mtu change so keeping the
protection flag there is not a good idea. Move it to struct
net_device_context which is preserved.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The framework only asserts (for now) that the reset gpio is not active.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 15 May 2016 17:47:27 +0000 (13:47 -0400)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2016-05-14
This series contains updates to i40e and i40evf.
Kevin adds support to disable link on all ports and changes bits set
for telling firmware the PHY needs to be modified by the driver.
Anjali adds a feature to enable/disable all multicast for a trusted
VF. Added priv-flag knob to configure global true promiscuous
support.
Shannon adds the support code for calling the admin queue API call
aq_set_switch_config().
Mitch modifies the VF, to log a message if an untrusted VF attempts to
configure promiscuous mode, but lies to it and returns everything is ok
instead of returning an error. Corrects the logic for reporting the
receive packet hash. Fixed the adding of a broadcast filter for VFs,
since that all VSIs are configured to receive broadcasts as default,
so do not need to add a filter.
Catherine refactors the ethtool get_settings to report the possible
supported link modes from what we know about the current PHY type and
that with the firmware supported PHY types.
Jacob changes the driver to use WARN_ONCE in order to highlight the
issue, but do not display a warning every time when receive hang
message is received.
Akeem corrects receive ptype payload layer for non_tunneled IPv6, when
it should be layer 4 for UDP, instead of layer 3.
Dan Carpenter fixes an uninitialized variable bug.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 15 May 2016 17:35:49 +0000 (13:35 -0400)]
Merge branch 'bnxt_en-next'
Michael Chan says:
====================
bnxt_en: updates for net-next.
Non-critical bug fixes, improvements, a new ethtool feature, and a new
device ID.
v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.
Ajit Khaparde (2):
bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO
bnxt_en: Report PCIe link speed and width during driver load
Michael Chan (6):
bnxt_en: Reduce maximum ring pages if page size is 64K.
bnxt_en: Improve the delay logic for firmware response.
bnxt_en: Fix length value in dmesg log firmware error message.
bnxt_en: Simplify and improve unsupported SFP+ module reporting.
bnxt_en: Add BCM57314 device ID.
bnxt_en: Use dma_rmb() instead of rmb().
Satish Baddipadige (1):
bnxt_en: Fix invalid max channel parameter in ethtool -l.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 15 May 2016 07:04:51 +0000 (03:04 -0400)]
bnxt_en: Use dma_rmb() instead of rmb().
Use the weaker but more appropriate dma_rmb() to order the reading of
the completion ring.
Suggested-by: Ajit Khaparde <ajit.khaparde@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 15 May 2016 07:04:49 +0000 (03:04 -0400)]
bnxt_en: Simplify and improve unsupported SFP+ module reporting.
The current code is more complicated than necessary and can only report
unsupported SFP+ module if it is plugged in after the device is up.
Rename bnxt_port_module_event() to bnxt_get_port_module_status(). We
already have the current module_status in the link_info structure, so
just check that and report any unsupported SFP+ module status. Delete
the unnecessary last_port_module_event. Call this function at the
end of bnxt_open to report unsupported module already plugged in.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 15 May 2016 07:04:47 +0000 (03:04 -0400)]
bnxt_en: Improve the delay logic for firmware response.
The current code has 2 problems:
1. The maximum wait time is not long enough. It is about 60% of the
duration specified by the firmware. It is calling usleep_range(600, 800)
for every 1 msec we are supposed to wait.
2. The granularity of the delay is too coarse. Many simple firmware
commands finish in 25 usec or less.
We fix these 2 issues by multiplying the original 1 msec loop counter by
40 and calling usleep_range(25, 40) for each iteration.
There is also a second delay loop to wait for the last DMA word to
complete. This delay loop should be a very short 5 usec wait.
This change results in much faster bring-up/down time:
Before the patch:
time ip link set p4p1 up
real 0m0.120s
user 0m0.001s
sys 0m0.009s
After the patch:
time ip link set p4p1 up
real 0m0.030s
user 0m0.000s
sys 0m0.010s
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sun, 15 May 2016 07:04:46 +0000 (03:04 -0400)]
bnxt_en: Reduce maximum ring pages if page size is 64K.
The chip supports 4K/8K/64K page sizes for the rings and we try to
match it to the CPU PAGE_SIZE. The current page size limits for the rings
are based on 4K/8K page size. If the page size is 64K, these limits are
too large. Reduce them appropriately.
Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Sun, 15 May 2016 07:04:45 +0000 (03:04 -0400)]
bnxt_en: Report PCIe link speed and width during driver load
Add code to log a message during driver load indicating PCIe link
speed and width.
The log message will look like this:
bnxt_en 0000:86:00.0 eth0: PCIe: Speed 8.0GT/s Width x8
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Sun, 15 May 2016 07:04:44 +0000 (03:04 -0400)]
bnxt_en: Add Support for ETHTOOL_GMODULEINFO and ETHTOOL_GMODULEEEPRO
Add support to fetch the SFP EEPROM settings from the firmware
and display it via the ethtool -m command. We support SFP+ and QSFP
modules.
v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en: Fix invalid max channel parameter in ethtool -l.
When there is only 1 MSI-X vector or in INTA mode, tx and rx pre-set
max channel parameters are shown incorrectly in ethtool -l. With only 1
vector, bnxt_get_max_rings() will return -ENOMEM. bnxt_get_channels
should check this return value, and set max_rx/max_tx to 0 if it is
non-zero.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: e54bcde3d69d ("arm64: eBPF JIT compiler") Signed-off-by: Zi Shen Lim <zlim.lnx@gmail.com> Acked-by: Will Deacon <will.deacon@arm.com> Acked-by: Yang Shi <yang.shi@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 14 May 2016 18:11:44 +0000 (11:11 -0700)]
nf_conntrack: avoid kernel pointer value leak in slab name
The slab name ends up being visible in the directory structure under
/sys, and even if you don't have access rights to the file you can see
the filenames.
Just use a 64-bit counter instead of the pointer to the 'net' structure
to generate a unique name.
This code will go away in 4.7 when the conntrack code moves to a single
kmemcache, but this is the backportable simple solution to avoiding
leaking kernel pointers to user space.
Fixes: 5b3501faa874 ("netfilter: nf_conntrack: per netns nf_conntrack_cachep") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 14 May 2016 18:59:43 +0000 (11:59 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"Overlayfs fixes from Miklos, assorted fixes from me.
Stable fodder of varying severity, all sat in -next for a while"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ovl: ignore permissions on underlying lookup
vfs: add lookup_hash() helper
vfs: rename: check backing inode being equal
vfs: add vfs_select_inode() helper
get_rock_ridge_filename(): handle malformed NM entries
ecryptfs: fix handling of directory opening
atomic_open(): fix the handling of create_error
fix the copy vs. map logics in blk_rq_map_user_iov()
do_splice_to(): cap the size before passing to ->splice_read()
Mitch Williams [Tue, 3 May 2016 22:13:19 +0000 (15:13 -0700)]
i40e: don't add broadcast filter for VFs
Now that all VSIs are configured to receive broadcasts as default, we
don't need to add a filter. This eliminates an annoying but harmless
error message each time VFs are created or reset.
Change-ID: I4cd6339684df45b0d2722133eeb84c14fa93ea19 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Tue, 3 May 2016 22:13:18 +0000 (15:13 -0700)]
i40e/i40evf: properly report Rx packet hash
This logic is inverted. If the RXHASH flag is set, then we should go
ahead and call skb_set_hash.
Change-ID: Ib2e30356dced1d3e939c8061ab6ad5bd94197e7c Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ashish Shah [Tue, 3 May 2016 22:13:17 +0000 (15:13 -0700)]
i40e: set context to use VSI RSS LUT for SR-IOV
For the SR-IOV VSIs, when the queue filtering section is valid,
the RSS LUT needs to be set to use the VSI specific lookup table
(otherwise it will use the PF RSS LUT table).
Change-ID: Ia9377cc818078238a75c3bdeade1b593a91b3480 Signed-off-by: Ashish Shah <ashish.n.shah@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40e: Correct UDP packet header for non_tunnel-ipv6
This patch corrects Rx ptype payload layer for non_tunneled ipv6. It
should be layer 4 for UDP, instead of layer 3.
Change-ID: I9382e4458ab3c4e58f6d2e9f195d5d4ee513805e Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Tue, 3 May 2016 22:13:15 +0000 (15:13 -0700)]
i40e: change Rx hang message into a WARN_ONCE
Use WARN_ONCE in order to highlight the issue, but don't display
a warning every time. The user should be able to see the ethtool counter
we created if necessary to see how often it is occurring.
Change-ID: I40c4ea159819b64a7d33b7f5716749089791533a Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously we were only looking at the FW supported PHY types if link
was down, because we want to be more specific when link is up. This
refactor changes this. When link is down, we still rely on the FW
supported PHY types, but when link is up, we select the possible
supported link modes from what we know about the current PHY type, and
AND that with the FW supported PHY types.
Change-ID: Ice5dad83f2a17932b0b8b59f07439696ad6aa013 Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Tue, 3 May 2016 22:13:13 +0000 (15:13 -0700)]
i40e: lie to the VF
If an untrusted VF attempts to configure promiscuous mode, log a message
pointing out its naughty behavior. But then, instead of returning an
error to the offender, just lie to it and say everything's OK. It will
continue on its way, thinking it's in promiscuous mode, but receiving no
packets except its own.
Change-ID: I63369215b1720f3c531eedfc06af86ff8c0e3dc8 Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.
The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.
For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.
Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP : off
LinkPolling : off
flow-director-atr : on
veb-stats : off
hw-atr-eviction : off
vf-true-promisc-support: off
to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on
At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic
Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94 Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Tue, 3 May 2016 22:13:11 +0000 (15:13 -0700)]
i40e: Implement the API function for aq_set_switch_config
Add the support code for calling the AdminQ API call aq_set_switch_config
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kevin Scott [Tue, 3 May 2016 22:13:09 +0000 (15:13 -0700)]
i40e: Add support for disabling all link and change bits needed for PHY interactions
Add flag to tell firmware to disable link on all ports.
This patch changes the bits set for telling firmware the PHY needs
to be modified by driver. Without this patch, the setting will only
set that mode for the current port on the device. Because the
MDIO interface is common for the copper device. The command needs to
set the mode for all ports.
Change-ID: I8baa7da91d384291ac95b41ae1a516604f8eb67f Signed-off-by: Kevin Scott <kevin.c.scott@intel.com> Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Sat, 14 May 2016 01:08:24 +0000 (21:08 -0400)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2016-05-13
This series contains updates to e1000e, igb and igbvf.
Steve Shih fixes an issue for disabling auto-negotiation and forcing
speed and duplex settings for non-copper media.
Brian Walsh cleanups some inconsistency in the use of return variables
names to avoid confusion.
Jake cleans up the drivers to use the BIT() macro when it can, which will
future proof the drivers for GCC 6 when it gets released. Cleaned up
dead code which was never being used. Also fixed e1000e, where it was
incorrectly restting the SYSTIM registers every time the ioctl was being
run.
Denys Vlasenko fixes an oversight where incvalue variable holds a 32
bit value so we should declare it as such, instead of 64 bits. Also
fixed an overflow check, where two reads are the same, then it is not
an overflow.
Nathan Sullivan fixes the PTP timestamps for transmit and receive
latency based on the current link speed.
Alexander Duyck adds support for partial GSO segmentation in the case
of tunnels for igb and igbvf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>