Johannes Berg [Wed, 22 Sep 2010 16:02:01 +0000 (18:02 +0200)]
iwlwifi: move agn specific station code there
By duplicating a little bit of code between 3945
and agn, we can move a lot of code into an agn
specific station management file and thus reduce
the amount of code in core that is dead to 3945.
before:
text data bss dec hex filename
212886 3872 96 216854 34f16 iwlcore.ko
620542 10448 304 631294 9a1fe iwlagn.ko
314013 3264 196 317473 4d821 iwl3945.ko
after:
text data bss dec hex filename
202857 3872 92 206821 327e5 iwlcore.ko
629102 10448 308 639858 9c372 iwlagn.ko
314240 3264 196 317700 4d904 iwl3945.ko
Johannes Berg [Wed, 22 Sep 2010 16:01:59 +0000 (18:01 +0200)]
iwlwifi: rename iwl_mac_beacon_update
Rename iwl_mac_beacon_update to iwlcore_beacon_update
and make the calling convention a bit different. The
old name with _mac_ indicated that it was a mac80211
callback, but that's no longer true.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The following commit removed DISABLE_REGWRITE_BUFFER ops. The unnecessary
REGWRITE_BUFFER_FLUSH was not removed properly which is causing failure on
hw reset.
Author: Felix Fietkau <nbd@openwrt.org>
Date: Tue Oct 5 12:03:42 2010 +0200
ath9k_hw: clean up register write buffering
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 7 Oct 2010 11:10:30 +0000 (13:10 +0200)]
nl80211: use new genl helpers for WDS
Bill Jordan's patch to allow setting the WDS
peer crossed with my patch removing all the
boilerplate code in nl80211, and consequently
he didn't make use of it yet. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 7 Oct 2010 10:55:24 +0000 (12:55 +0200)]
mac80211: fix sw scan locking
The recent scan overhaul broke locking
because now we can jump to code that
attempts to unlock, while we don't have
the mutex held. Fix this by holding the
mutex around all the relevant code.
Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Thu, 7 Oct 2010 07:16:42 +0000 (10:16 +0300)]
wl1271: Support FEM autodetection
In the NVS/INI-parameters for the driver/firmware there is the FEM
(front end module) selection option, which may configure the hardware FEM
via autodetection or manual selection. So far, there has been support for
manual selection only.
Add support for FEM autodetection.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This commit relies on commit 5ed3bc7288487bd4f891f420a07319e0b538b4fe
("mac80211: use netif_receive_skb in ieee80211_tx_status callpath")
Unfortunately not all drivers are calling ieee80211_tx_status from a
compatible context, so that commit needs to be reverted in 2.6.36.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 6 Oct 2010 19:18:04 +0000 (21:18 +0200)]
cfg80211: fix BSS double-unlinking
When multiple interfaces are actively trying
to associate with the same BSS, they may both
find that the BSS isn't there and then try to
unlink it. This can cause errors since the
unlinking code can't currently deal with items
that have already been unlinked.
Normally this doesn't happen as most people
don't try to use multiple station interfaces
that associate at the same time too.
Fix this by using the list entry as a flag to
see if the item is still on a list.
Cc: stable@kernel.org Reported-by: Ben Greear <greearb@candelatech.com> Tested-by: Hun-Kyi Wynn <hkwynn@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Wed, 6 Oct 2010 09:34:12 +0000 (18:34 +0900)]
nl80211/mac80211: Add retry and failed transmission count to station info
This information is already available in mac80211, we just need to export it
via cfg80211 and nl80211.
Signed-off-by: Bruno Randolf <br1@einfach.org> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Revert "iwlwifi: do not perferm force reset while doing scan"
This reverts commit 7acc7c683a747689aaaaad4fce1683fc3f85e552. It was
applied to avoid possible warning in ieee80211_restart_hw, however
reason of the warning were races in mac80211, currently hopefully fixed.
Not reseting device when performing scan is bad for two reasons.
When forcing reset from iwl_check_stuck_queue(), in case of fail,
reset will be repeated until scan finish. But since firmware is in bad
shape, scan only finish after scan_check work (about 7s). So we will
delay the reset, what is not good behaviour.
When forcing reset from iwl_recover_from_statistics(), we will not
repeat the reset, so we will not perform reset at all when needed.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: compete scan to cfg80211 if deferred scan fail to start
We nulify local->scan_req on failure in __ieee80211_start_scan, so
__ieee80211_scan_completed will not call cfg80211_scan_done. Fix that.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: do not requeue scan work when not needed
When performing hw scan and not abort it, __ieee80211_scan_completed()
is currently called from scan work, so does not need to reschedule work
to call drv_hw_scan().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cfg80211 request the scan and mac80211 perform some management work,
we defer the scan request. We do not canceling such requests when calling
ieee80211_scan_cancel(), because of SCAN_SW_SCANNING bit check just
before the call. So fix that problem.
Another problem, which commit 85f72bc839705294b32b6c16b491c0422f0a71b3
tries to solve, is we can not cancel HW scan. Hence patch make
ieee80211_scan_cancel() ignore HW scan (see code comments). Keeping
local->mtx lock assures that the deferred scan will not become
"working" HW scan.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: keep lock when calling __ieee80211_scan_completed()
We are taking local->mtx inside __ieee80211_scan_completed(), but just
before call to that function we drop the lock. Dropping/taking lock is not
good, because can lead to hard to understand race conditions.
Patch split scan_completed() code into two functions, first must be called
with local->mtx taken and second without it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: reduce number of __ieee80211_scan_completed calls
Use goto instruction to call __ieee80211_scan_completed only ones in
ieee80211_scan_work. This is prepare for the next patch.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Oct 2010 17:39:30 +0000 (19:39 +0200)]
cfg80211/mac80211: allow per-station GTKs
This adds API to allow adding per-station GTKs,
updates mac80211 to support it, and also allows
drivers to remove a key from hwaccel again when
this may be necessary due to multiple GTKs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Oct 2010 17:37:40 +0000 (19:37 +0200)]
mac80211: avoid transmitting delBA to old AP
When roaming while we have active BA session,
we can end up transmitting delBA frames to
the old AP while we're already on the new AP's
channel, which can cause warnings.
Simply avoid sending those frames, but still
tear down the internal session state, since
they are not really necessary anyway as we
will implicitly disassociate when sending the
association to the new AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 4 Oct 2010 18:09:50 +0000 (20:09 +0200)]
ath9k_hw: merge ath9k_hw_ani_monitor_old and ath9k_hw_ani_monitor_new
After the last rounds of cleanup, these functions are now functionally
equivalent and can thus be merged.
Also get rid of some excessive (and redundant) debug messages.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 4 Oct 2010 18:09:49 +0000 (20:09 +0200)]
ath9k_hw: remove function pointer abstraction for internal ANI ops
The code gets more concise and readable when making the new ANI functions
fall back to the old ones if ANI v2 is disabled. This also makes further code
cleanup easier.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Mon, 4 Oct 2010 18:09:48 +0000 (20:09 +0200)]
ath9k_hw: remove code duplication in phy error counter handling
Split out the PHY error counter update from ath9k_hw_ani_monitor_*, reuse
it in ath9k_hw_proc_mib_event (merged from ath9k_hw_proc_mib_event_old
and ath9k_hw_proc_mib_event_new).
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 5 Oct 2010 10:03:42 +0000 (12:03 +0200)]
ath9k_hw: clean up register write buffering
Throughout the code, DISABLE_REGWRITE_BUFFER is always called right after
REGWRITE_BUFFER_FLUSH. Since that's unlikely to change any time soon, that
makes keeping those ops separate rather pointless, as it only increases
code size and line number counts.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 3 Oct 2010 17:07:17 +0000 (19:07 +0200)]
ath9k_hw: merge codepaths that access the cycle counter registers
The cycle counters are used by ANI to determine the amount of time that the
radio spent not receiving or transmitting. They're also used for debugging
purposes if the baseband watchdog on AR9003 detects a lockup.
In the future, we want to use these counters to determine the medium utilization
and export this information via survey. For that, we need to make sure that
the counter is only accessed from one place, which also ensures that
wraparounds won't occur at inconvenient points in time.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sun, 3 Oct 2010 17:07:16 +0000 (19:07 +0200)]
ath9k_hw: clean up calibration flags
The calibration actual calibration flags are only used by the per chip family
source files, so it makes more sense to define them in those files instead
of globally. That way the code has to test for less flags.
Also instead of using a separate callback for testing whether a particular
calibration type is supported, simply adjust ah->supp_cals in the calibration
init which is called right after the hardware reset, before any of the
calibrations are run.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Oct 2010 19:40:33 +0000 (21:40 +0200)]
mac80211: delete AddBA response timer
We never delete the addBA response timer, which
is typically fine, but if the station it belongs
to is deleted very quickly after starting the BA
session, before the peer had a chance to reply,
the timer may fire after the station struct has
been freed already. Therefore, we need to delete
the timer in a suitable spot -- best when the
session is being stopped (which will happen even
then) in which case the delete will be a no-op
most of the time.
I've reproduced the scenario and tested the fix.
This fixes the crash reported at
http://mid.gmane.org/4CAB6F96.6090701@candelatech.com
Cc: stable@kernel.org Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Wed, 6 Oct 2010 15:10:00 +0000 (08:10 -0700)]
iwlagn: reduce redundant parameter definitions
move paramater definitions to a device paramater structure only
leaving the device name, which antennas are used and what firmware
file to use in the iwl_cfg structure. this will not completely
remove the redundancies but greatly reduce them for devices that
only vary by name or antennas. the parameters that are more
likely to change within a given device family are left in iwl_cfg.
also separate bt param structure added to help reduce more.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Wey-Yi Guy [Wed, 6 Oct 2010 14:42:43 +0000 (07:42 -0700)]
iwlwifi: schedule to deprecate software scan support
Hardware scan is the prefer method for all iwlwifi devices;
especially for dual-mode functions. Schedule to deprecate the
software scan support in kernel 2.6.40
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
mac80211: fix channel assumption for association done work
Be consistent and use the wk->chan instead of the
local->hw.conf.channel for the association done work.
This prevents any possible races against channel changes
while we run this work.
In the case that the race did happen we would be initializing
the bit rates for the new AP under the assumption of a wrong
channel and in the worst case, wrong band. This could lead
to trying to assuming we could use CCK frames on 5 GHz, for
example.
This patch has a fix for kernels >= v2.6.34
Cc: stable@kernel.org Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Tue, 5 Oct 2010 09:32:17 +0000 (11:32 +0200)]
ath9k: get correct tx gain type in ath9k_hw_4k_get_eeprom
The base_eep_header_4k structure contains information that the
device supports high power tx gain table or not. However the
ath9k_hw_4k_get_eeprom function does not return that value when
it is called with EEP_TXGAIN_TYPE. This leads to that the tx gain
initialization will use the init values from the original tx gain
table even if the device inidicates that the high power table
should be used.
Changes-licensed-under: ISC Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: Shu Hwa Shen <shensh@zcomm.com.cn> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Tue, 5 Oct 2010 04:27:17 +0000 (13:27 +0900)]
ath5k: Don't wake internal queues
We should only wake up queues which mac80211 knows about (queues 0-3). We have
another internal queue ("CAB", queue number 6) which we use for power-saved
frames. When transmitted frames are processed from this queue, we have to make
sure we don't bother mac80211 with waking a queue it doesn't know about.
this fixes:
WARNING: at /home/br1/ath/wireless-testing/net/mac80211/util.c:275
__ieee80211_wake_queue+0xd6/0xe0 [mac80211]()
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 5 Oct 2010 08:41:47 +0000 (10:41 +0200)]
mac80211: fix deadlock with multiple interfaces
The locking around ieee80211_recalc_smps is
buggy -- it cannot acquire another interface's
mutex while the iflist mutex is held because
another code path could be holding the iface
mutex and trying to acquire the iflist mutex.
But the locking is also unnecessary, we only
check "ifmgd->associated" as a bool, and don't
use the pointer (in check_mgd_smps).
Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 4 Oct 2010 19:14:03 +0000 (21:14 +0200)]
genetlink: introduce pre_doit/post_doit hooks
Each family may have some amount of boilerplate
locking code that applies to most, or even all,
commands.
This allows a family to handle such things in
a more generic way, by allowing it to
a) include private flags in each operation
b) specify a pre_doit hook that is called,
before an operation's doit() callback and
may return an error directly,
c) specify a post_doit hook that can undo
locking or similar things done by pre_doit,
and finally
d) include two private pointers in each info
struct passed between all these operations
including doit(). (It's two because I'll
need two in nl80211 -- can be extended.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bruno Randolf [Mon, 4 Oct 2010 02:17:30 +0000 (11:17 +0900)]
mac80211: Add WME information element for IBSS
Enable WME QoS in IBSS mode by adding a WME information element to beacons and
probe respones and by checking for it and marking stations as WME capable if it
is present.
Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:34:56 +0000 (11:34 +0200)]
rt2x00: Work around hw aggregation oddity in rt2800
If a frame is not meant to be sent as AMPDU or part of it the hw might
still decide to aggregate this frame if a previous frame started an
AMPDU. However, this will limit the usefulness of the reported tx rate
since the reported rate will be the one specified in the TXWI of the
first frame and thus it is not possible to reliably caculate the
number of retrys by substracting the reported tx rate from the tx rate
in the TXWI.
To fix this issue, only report the successful rate for frames that were
not meant to be aggregated but ended up in an aggregate.
Example:
Frame A (MCS7, AMPDU=1) B (MCS7, AMPDU=1) C (MCS12, AMDPU=0, PROBE_RATE)
Although frame C shoudn't be aggregated the hw might sill put it
into an AMPDU together with A and B. If the transmission succeeds the tx
status will contain MCS7 for all three frames. In that case we should
only report MCS7 as success rate and avoid reporting MCS12-MCS8 as
failed tx attempts as this will affect the future rate control
decisions.
This oddity might strike us in other scenarious as well but the most
common "wrong" report happened for frames used to probe a different tx
rate.
This improves the rate control decisions notable.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:34:26 +0000 (11:34 +0200)]
rt2x00: Improve cooperation between rt2800pci and minstrel
In order to lower the impact of probe rates don't send a frame as AMPDU
if the rate control algorithm sets IEEE80211_TX_CTL_RATE_CTRL_PROBE.
Otherwise a whole aggregate would be send with a probe rate which might
lead to numerous retries.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:34:05 +0000 (11:34 +0200)]
rt2x00: Fix oops caused by error path in rt2x00lib_start
When rt2x00lib_enable_radio fails to enable the radio, rt2x00lib_start
will call rt2x00queue_uninitialize to uninitialize the queues. Since,
the queues are not initialized here but already in rt2x00lib_initialize
we shouldn't uninitialize the queues here. Otherwise, a consecutive call
to rt2x00lib_start will oops (see below) because it assumes the queues
are already initialized.
Reported-by: Joshua Smith <jesmith@kaon.com> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:33:42 +0000 (11:33 +0200)]
rt2x00: Update comment about the AMPDU flag in the TXWI
During testing with AMPDUs it turned out that the rt2800 hw will aggregate
consecutive frames with the same RA and TID when the first frame in a
possible aggregate has set AMPDU=1 in the TXWI. If a following frame has
set AMPDU=0 in its TXWI it might sill end up in the aggregate of the
previous frame. Update the comment accordingly.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:33:17 +0000 (11:33 +0200)]
rt2x00: Enable rx aggregation in rt2800
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 2 Oct 2010 09:32:43 +0000 (11:32 +0200)]
rt2x00: Improve TX status entry validation
The TX_STA_FIFO contains some information for identifying
a outgoing frame, however matching by WCID and ACK status is
not sufficient to 100% identify the macthing queue_entry structure
(containing the SKB buffer) which belongs to the status report.
Within TX_STA_FIFO we have a 4-bit field named PACKETID, which is
currently used to encode the queue id. The queue ID is however
limited to values from 0 to 3, which means 2 bits are sufficient
to encode the value. With the remaining 2 bits we can encode a
partial queue_entry index number. The value of PACKETID is not
allowed to become 0, with the queue ID ranging from 0 to 3, at least
one of the bits for the entry identification must be 1.
That leaves us with 3 possible values we can still encode in the
bits. Altough this doesn't allow 100% accurate matching of the
TX_STA_FIFO queue to a queue_entry structure, it at least improves
the accuracy. This allows us to better detect if we have missed the
TX_STA_FIFO report, which in turn reduces the number of watchdog
warnings regarding the TX status timeout.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:32:16 +0000 (11:32 +0200)]
rt2x00: correctly set max_report_rates in rt61pci and rt2800
rt61pci and rt2800 devices can use up to 7 different rates per tx frame.
However, the device uses a global fallback table. Hence, the rc
algortihm cannot specify multiple rates to try but the device is able to
report multiple rates (based on the retry table). Specify that behavior
by correctly setting max_report_rates and max_rates.
This makes rt2x00 and minstrel play nicer together.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:31:55 +0000 (11:31 +0200)]
mac80211: distinct between max rates and the number of rates the hw can report
Some drivers cannot handle multiple retry rates specified by the rc
algorithm but instead use their own retry table (for example rt2800).
However, if such a device registers itself with a max_rates value of 1
the rc algorithm cannot make use of the extended information the device
can provide about retried rates. On the other hand, if a device
registers itself with a max_rates value > 1 the rc algorithm assumes
that the device can handle multi rate retries.
Fix this issue by introducing another hw parameter max_report_rates that
can be set to a different value then max_rates to indicate if a device
is capable of reporting more rates then specified in max_rates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:31:33 +0000 (11:31 +0200)]
rt2x00: Don't enable broad- and multicast buffering on USB devices
Since rt2x00 USB devices have no chance to know when a beacon was sent
out in AP mode currently all broad- and multicast traffic is buffered in
mac80211 but never sent out at all.
Unfortunately we have no chance in sending the traffic out after a
DTIM beacon due to hw limitations. Hence, instead of never sending the
buffered traffic out better send it out immediately.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Reported-by: Lauri Hintsala <lauri.hintsala@bluegiga.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:31:05 +0000 (11:31 +0200)]
rt2x00: add field definitions for the TBTT_SYNC_CFG register
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:30:42 +0000 (11:30 +0200)]
rt2x00: Add register definition for busy time on secondary channel
Add the register definition CH_BUSY_STA_SEC for reading the busy time
on the secondary channel in HT40 mode. Also update the comments about
channel busy/idle time registers to express the used unit.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:29:59 +0000 (11:29 +0200)]
rt2x00: Allow tx duplication for legacy rates in HT40 mode
Make use of the IEEE80211_TX_RC_DUP_DATA flag to duplicate a
transmission with legacy rates to both 20Mhz channels if set.
Also update the related comment in rt2800.h to describe the
behavior of the BW_40 flag for legacy rates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:29:30 +0000 (11:29 +0200)]
rt2x00: Fix race between dma mapping and clearing rx entries in rt2800pci
During rx, rt2x00lib calls rt2800pci_fill_rxdone to read the RX
descriptor. At that time the skb is already dma unmapped but no new skb
was dma mapped for this entry again. However, rt2800pci_fill_rxdone also
moves the hw rx queue index, marking this entry to be available for
reuse. Since no new skb was dma mapped and also the previous skb was
unmapped this might lead to strange hw behavior.
To fix this issue move the hw rx queue index increment to
rt2800pci_clear_entry where a new skb was already dma mapped and can be
safely used by the hw.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:29:08 +0000 (11:29 +0200)]
rt2x00: Don't initialize MM40 HT protection to RTS/CTS on PCI devices
Since HT protection is now configurable via mac80211 we don't need this
special case for PCI devices anymore. The HT protection config will be
overwritten as soon as mac80211 sends us a HT operation mode. Hence,
bring the HT MM40 protection config in sync with the other HT protection
registers and initialize it to no protection.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:28:34 +0000 (11:28 +0200)]
rt2x00: Implement HT protection for rt2800
Update the HT operation mode when mac80211 sends it to us and set
the different HT protection modes and rates accordingly. For now
only use CTS-to-self with OFDM 24M or CCK 11M when protection is
required.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:28:02 +0000 (11:28 +0200)]
rt2x00: Fix SM PS check
Fix a check for dynamic SM PS mode in the STAs HT caps. Since a
value of 3 means "SM PS disabled" the previous check assumed in
that case that "dynamic SM PS" was enabled and as such prefixed
every MCS>7 frame with a unnecessary RTS/CTS exchange. Also,
the bit shift was done in the wrong direction.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:27:35 +0000 (11:27 +0200)]
rt2x00: rework tx status handling in rt2800pci
This patch changes the way tx status reports are handled by rt2800pci.
Previously rt2800pci would sometimes lose tx status reports as the
TX_STA_FIFO register is a fifo of 16 entries that can overflow in case
we don't read it often/fast enough. Since interrupts are disabled in the
device during the execution of the interrupt thread it happend sometimes
under high network and CPU load that processing took too long and a few
tx status reports were dropped by the hw.
To fix this issue the TX_STA_FIFO register is read directly in the
interrupt handler and stored in a kfifo which is large enough to hold
all status reports of all used tx queues.
To process the status reports a new tasklet txstatus_tasklet is used.
Using the already used interrupt thread is not possible since we don't
want to disable the TX_FIFO_STATUS interrupt while processing them and
it is not possible to schedule the interrupt thread multiple times for
execution. A tasklet instead can be scheduled multiple times which
allows to leave the TX_FIFO_STATUS interrupt enabled while a previously
scheduled tasklet is still executing.
In short: All other interrupts are handled in the interrupt thread as
before. Only the TX_FIFO_STATUS interrupt is partly handled in the
interrupt handler and finished in the according tasklet.
One drawback of this patch is that it duplicates some code from
rt2800lib. However, that can be cleaned up in the future once the
rt2800usb and rt2800pci tx status handling converge more.
Using this patch on a Ralink RT3052 embedded board gives me a reliable
wireless connection even under high CPU and network load. I've
transferred several gigabytes without any queue lockups.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:27:03 +0000 (11:27 +0200)]
rt2x00: Split out parts of the rt2800_txdone function for easier reuse
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Sat, 2 Oct 2010 09:26:17 +0000 (11:26 +0200)]
rt2x00: Don't overwrite beacon buffers in pairwise key setup
rt2800 devices use parts of the pariwise key table to store the beacon
frames for beacon 6 and 7. To not overwrite the beacon frame buffers
limit the number of entries we store in the pairwise key table to 222.
Also add some descriptive comments about this shared memory usage.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 1 Oct 2010 13:02:31 +0000 (16:02 +0300)]
mac80211: Add validity check for beacon_crc value
On association to an AP, after receiving beacons, the beacon_crc value is set.
The beacon_crc value is not reset in disassociation, but the BSS data may be
expired at a later point. When associating again, it's possible that a
beacon for the AP is not received, resulting in the beacon_ies to remain NULL.
After association, further beacons will not update the beacon data, as the
crc value of the beacon has not changed, and the beacon_crc still holds a
value matching the beacon. The beacon_ies will remain forever null.
One of the results of this is that WLAN power save cannot be entered, the STA
will remain foreven in active mode.
Fix this by adding a validation flag for the beacon_crc, which is cleared on
association.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move ieee80211_scan_cancel() and all other related code to
ieee80211_restart_work() as ieee80211_restart_hw() is intended to be
callable from any context.
Fix a bug that RTNL lock is not taken during ieee80211_cancel_scan().
Take local->mtx before WARN(test_bit(SCAN_HW_SCANNING, &local->scanning)
to prevent the race condition with __ieee80211_start_scan() described
here: http://marc.info/?l=linux-wireless&m=128516716810537&w=2
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the ath9k debugging feature 'wiphy' the current channel used by the
station is incorrectly displayed.This is because the channels available
are sequentially mapped from numbers 0 to 37.This mapping cannot be
changed as the channel number is also used as an array index
This fix solves the above problem by calculating the channel
number from center frequency.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Thu, 30 Sep 2010 23:06:53 +0000 (01:06 +0200)]
ath9k: fix channel flag / regd issues with multiple cards
Since the regulatory code touches the channel array, it needs to be
copied for each device instance. That way the original channel array
can also be made const.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org [all] Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 30 Sep 2010 19:21:25 +0000 (21:21 +0200)]
cfg80211: remove spurious __KERNEL__ ifdef
The net/cfg80211.h header file isn't exported to
userspace, so there's no need for any kind of
__KERNEL__ protection in it. If it was exported,
everything else in it would need protection as
well, not just the logging stuff ...
Cc:Joe Perches <joe@perches.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 30 Sep 2010 19:06:09 +0000 (21:06 +0200)]
cfg80211/mac80211: allow management frame TX in AP mode
Enable management frame transmission and subscribing
to management frames through nl80211 in both cfg80211
and mac80211. Also update a few places that I forgot
to update for P2P-client mode previously, and fix a
small bug with non-action frames in this API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: change WARN_ON to IWL_WARN in iwl_mac_add_interface
We can start restarting firmware or RF kill switch can be turned on
during call to iwl_mac_add_interface(). That are normal working
conditions, so do not print call trace, just print simple message
instead.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / karo-tx-linux.git / log