Dave Airlie [Sat, 16 Jul 2016 01:25:11 +0000 (11:25 +1000)]
Merge tag 'drm-vc4-next-2016-07-15' of https://github.com/anholt/linux into drm-next
This pull request brings in vc4 shader validation for branching,
allowing GLSL shaders with non-unrolled loops.
* tag 'drm-vc4-next-2016-07-15' of https://github.com/anholt/linux:
drm/vc4: Fix a "the the" typo in a comment.
drm/vc4: Fix definition of QPU_R_MS_REV_FLAGS
drm/vc4: Add a getparam to signal support for branches.
drm/vc4: Add support for branching in shader validation.
drm/vc4: Add a bitmap of branch targets during shader validation.
drm/vc4: Move validation's current/max ip into the validation struct.
drm/vc4: Add a getparam ioctl for getting the V3D identity regs.
Dave Airlie [Sat, 16 Jul 2016 01:24:29 +0000 (11:24 +1000)]
Merge tag 'drm/panel/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/panel: Changes for v4.8-rc1
This set of changes contains a few cleanups for existing panels as well
as improved handling of certain backlights. In addition there's support
for a few new simple panels.
* tag 'drm/panel/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/panel: simple: Add support for Starry KR122EA0SRA panel
dt-bindings: Add Starry KR122EA0SRA panel binding
dt-bindings: Add vendor prefix for Starry
dt-bindings: display: Add Sharp LQ101K1LY04 panel binding
drm/panel: simple: Add support for Sharp LQ101K1LY04
drm/panel: simple: Add support for LG LP079QX1-SP0V panel
dt-bindings: Add support for LG LP079QX1-SP0V panel
drm/panel: simple: Add support for Sharp LQ123P1JX31 panel
dt-bindings: Add Sharp LQ123P1JX31 panel binding
drm/panel: simple: Add support for Samsung LSN122DL01-C01 panel
dt-bindings: Add Samsung LSN122DL01-C01 panel binding
drm/panel: simple: Add support for LG LP097QX1-SPA1 panel
dt-bindings: Add LG LP097QX1-SPA1 panel binding
drm/panel: simple: Update backlight state property
drm/panel: simple: Remove gratuitous blank line
drm/panel: simple: Fix a couple of physical sizes
Dave Airlie [Sat, 16 Jul 2016 01:23:50 +0000 (11:23 +1000)]
Merge tag 'drm/tegra/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v4.8-rc1
This set of changes contains a bunch of cleanups to the host1x driver as
well as the addition of a pin controller for DPAUX, which is required by
boards to configure the DPAUX pads in AUX mode (for DisplayPort) or I2C
mode (for HDMI and DDC).
Included is also a bit of rework of the SOR driver in preparation to add
DisplayPort support as well as some refactoring and cleanup.
Finally, all output drivers are converted to runtime PM, which greatly
simplifies the handling of clocks and resets.
* tag 'drm/tegra/for-4.8-rc1' of git://anongit.freedesktop.org/tegra/linux: (35 commits)
drm/tegra: sor: Reject HDMI 2.0 modes
drm/tegra: sor: Prepare for generic PM domain support
drm/tegra: dsi: Prepare for generic PM domain support
drm/tegra: sor: Make XBAR configurable per SoC
drm/tegra: sor: Use sor1_src clock to set parent for HDMI
dt-bindings: display: tegra: Add source clock for SOR
drm/tegra: sor: Implement sor1_brick clock
drm/tegra: sor: Implement runtime PM
drm/tegra: hdmi: Implement runtime PM
drm/tegra: dsi: Implement runtime PM
drm/tegra: dc: Implement runtime PM
drm/tegra: hdmi: Enable audio over HDMI
drm/tegra: sor: Do not support deep color modes
drm/tegra: sor: Extract tegra_sor_mode_set()
drm/tegra: sor: Split out tegra_sor_apply_config()
drm/tegra: sor: Rename tegra_sor_calc_config()
drm/tegra: sor: Factor out tegra_sor_set_parent_clock()
drm/tegra: dpaux: Add pinctrl support
dt-bindings: Add bindings for Tegra DPAUX pinctrl driver
drm/tegra: Prepare DPAUX for supporting generic PM domains
...
Dave Airlie [Sat, 16 Jul 2016 01:21:50 +0000 (11:21 +1000)]
Merge branch 'upstream/analogix-dp-20160705' of git://github.com/yakir-Yang/linux into drm-next
Please consider merging this tag, which contains the v4 misc fixes and add RK3399 eDP support patches[0] I sent on 2016-06-29, rebased onto v4.7-rc5.
* 'upstream/analogix-dp-20160705' of git://github.com/yakir-Yang/linux:
dt-bindings: analogix_dp: rockchip: correct the wrong compatible name
drm/rockchip: analogix_dp: introduce the pclk for grf
drm/bridge: analogix_dp: fix no drm hpd event when panel plug in
drm/rockchip: analogix_dp: update the comments about why need to hardcode VOP output mode
drm/rockchip: analogix_dp: correct the connector display color format and bpc
drm/bridge: analogix_dp: passing the connector as an argument in .get_modes()
drm/rockchip: analogix_dp: make panel detect to an optional action
drm/rockchip: analogix_dp: add rk3399 eDP support
drm/bridge: analogix_dp: some rockchip chips need to flip REF_CLK bit setting
drm/bridge: analogix_dp: correct the register bit define error in ANALOGIX_DP_PLL_REG_1
drm/rockchip: analogix_dp: split the lcdc select setting into device data
Dave Airlie [Sat, 16 Jul 2016 01:19:29 +0000 (11:19 +1000)]
Merge tag 'imx-drm-next-2016-07-14' of git://git.pengutronix.de/git/pza/linux into drm-next
imx-drm updates
- atomic mode setting conversion
- replace DMFC FIFO allocation mechanism with a fixed allocation
that is good enough for all cases
- support for external bridges connected to parallel-display
- improved error handling in imx-ldb, imx-tve, and parallel-display
- some code cleanup in imx-tve
* tag 'imx-drm-next-2016-07-14' of git://git.pengutronix.de/git/pza/linux:
drm/imx: parallel-display: add bridge support
drm/imx: parallel-display: check return code from of_get_drm_display_mode()
gpu: ipu-v3: ipu-dc: don't bug out on invalid bus_format
drm/imx: imx-tve: fix the error message
drm/imx: imx-tve: remove unneeded 'or' operation
drm/imx: imx-tve: check the value returned by regulator_set_voltage()
drm/imx: imx-ldb: check return code on panel attach
drm/imx: turn remaining container_of macros into inline functions
drm/imx: store internal bus configuration in crtc state
drm/imx: remove empty mode_set encoder callbacks
drm/imx: atomic phase 3 step 3: Advertise DRIVER_ATOMIC
drm/imx: atomic phase 3 step 2: Legacy callback fixups
drm/bridge: dw-hdmi: Remove the legacy drm_connector_funcs structure
drm/imx: atomic phase 3 step 1: Use atomic configuration
drm/imx: Remove encoders' ->prepare callbacks
drm/imx: atomic phase 2 step 2: Track plane_state->fb correctly in ->page_flip
drm/imx: atomic phase 2 step 1: Wire up state ->reset, ->duplicate and ->destroy
drm/imx: atomic phase 1: Use transitional atomic CRTC and plane helpers
gpu: ipu-v3: ipu-dmfc: Use static DMFC FIFO allocation mechanism
drm/imx: ipuv3 plane: Check different types of plane separately
Eric Anholt [Sat, 2 Jul 2016 21:14:27 +0000 (14:14 -0700)]
drm/vc4: Add a getparam to signal support for branches.
Userspace needs to know if it can create shaders that do branching.
Otherwise, for backwards compatibility with old kernels it needs to
lower if statements to conditional assignments.
Eric Anholt [Sat, 2 Jul 2016 19:17:10 +0000 (12:17 -0700)]
drm/vc4: Add support for branching in shader validation.
We're already checking that branch instructions are between the start
of the shader and the proper PROG_END sequence. The other thing we
need to make branching safe is to verify that the shader doesn't read
past the end of the uniforms stream.
To do that, we require that at any basic block reading uniforms have
the following instructions:
The instructions are generated by userspace, and the kernel verifies
that the load_imm is of the expected offset, and that the add adds it
to a uniform. We track which uniform in the stream that is, and at
draw call time fix up the uniform stream to have the address of the
start of the shader's uniforms at that location.
Eric Anholt [Sat, 2 Jul 2016 17:10:24 +0000 (10:10 -0700)]
drm/vc4: Add a bitmap of branch targets during shader validation.
This isn't used yet, it's just a first step toward loop validation.
During the main parsing of instructions, we need to know when we hit a
new basic block so that we can reset validated state.
v2: Fix a stray semicolon after an if block. (caught by kbuild test).
Dave Airlie [Fri, 15 Jul 2016 04:05:41 +0000 (14:05 +1000)]
Merge branch 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
This pull request adds to the rework patch series for IOMMU
integration to support ARM64bit architecture with DMA-IOMMU
glue code.
With this patch series, Exynos DRM works well on Exynos5433 SoC
with IOMMU enabled.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: iommu: add support for ARM64 specific code for IOMMU glue
drm/exynos: iommu: move ARM specific code to exynos_drm_iommu.h
drm/exynos: iommu: remove unused entries from exynos_drm_private strcuture
drm/exynos: iommu: add a check if all sub-devices have iommu controller
drm/exynos: iommu: move dma_params configuration code to separate functions
Dave Airlie [Fri, 15 Jul 2016 03:56:11 +0000 (13:56 +1000)]
Merge tag 'drm-vc4-next-2016-07-12' of https://github.com/anholt/linux into drm-next
This pull request brings in new vc4 plane formats for Android, precise
vblank timestamping, and a couple of small cleanups.
* tag 'drm-vc4-next-2016-07-12' of https://github.com/anholt/linux:
drm/vc4: remove redundant ret status check
drm/vc4: Implement precise vblank timestamping.
drm/vc4: Bind the HVS before we bind the individual CRTCs.
gpu: drm: vc4_hdmi: add missing of_node_put after calling of_parse_phandle
drm: vc4: enable XBGR8888 and ABGR8888 pixel formats
drm/vc4: clean up error exit path on failed dpi_connector allocation
Dave Airlie [Fri, 15 Jul 2016 03:50:58 +0000 (13:50 +1000)]
Merge tag 'drm-intel-next-2016-07-11' of git://anongit.freedesktop.org/drm-intel into drm-next
- select igt testing depencies for CONFIG_DRM_I915_DEBUG (Chris)
- track outputs in crtc state and clean up all our ad-hoc connector/encoder
walking in modest code (Ville)
- demidlayer drm_device/drm_i915_private (Chris Wilson)
- thundering herd fix from Chris Wilson, with lots of help from Tvrtko Ursulin
- piles of assorted clean and fallout from the thundering herd fix
- documentation and more tuning for waitboosting (Chris)
- pooled EU support on bxt (Arun Siluvery)
- bxt support is no longer considered prelimary!
- ring/engine vfunc cleanup from Tvrtko
- introduce intel_wait_for_register helper (Chris)
- opregion updates (Jani Nukla)
- tuning and fixes for wait_for macros (Tvrkto&Imre)
- more kabylake pci ids (Rodrigo)
- pps cleanup and fixes for bxt (Imre)
- move sink crc support over to atomic state (Maarten)
- fix up async fbdev init ordering (Chris)
- fbc fixes from Paulo and Chris
* tag 'drm-intel-next-2016-07-11' of git://anongit.freedesktop.org/drm-intel: (223 commits)
drm/i915: Update DRIVER_DATE to 20160711
drm/i915: Select DRM_VGEM for igt
drm/i915: Select X86_MSR for igt
drm/i915: Fill unused GGTT with scratch pages for VT-d
drm/i915: Introduce Kabypoint PCH for Kabylake H/DT.
drm/i915:gen9: implement WaMediaPoolStateCmdInWABB
drm/i915: Check for invalid cloning earlier during modeset
drm/i915: Simplify hdmi_12bpc_possible()
drm/i915: Kill has_dsi_encoder
drm/i915: s/INTEL_OUTPUT_DISPLAYPORT/INTEL_OUTPUT_DP/
drm/i915: Replace some open coded intel_crtc_has_dp_encoder()s
drm/i915: Kill has_dp_encoder from pipe_config
drm/i915: Replace manual lvds and sdvo/hdmi counting with intel_crtc_has_type()
drm/i915: Unify intel_pipe_has_type() and intel_pipe_will_have_type()
drm/i915: Add output_types bitmask into the crtc state
drm/i915: Remove encoder type checks from MST suspend/resume
drm/i915: Don't mark eDP encoders as MST capable
drm/i915: avoid wait_for_atomic() in non-atomic host2guc_action()
drm/i915: Group the irq breadcrumb variables into the same cacheline
drm/i915: Wake up the bottom-half if we steal their interrupt
...
Dave Airlie [Fri, 15 Jul 2016 01:01:37 +0000 (11:01 +1000)]
Merge tag 'topic/drm-misc-2016-07-14' of git://anongit.freedesktop.org/drm-intel into drm-next
I recovered dri-devel backlog from my vacation, more misc stuff:
- of_put_node fixes from Peter Chen (not all yet)
- more patches from Gustavo to use kms-native drm_crtc_vblank_* funcs
- docs sphinxification from Lukas Wunner
- bunch of fixes all over from Dan Carpenter
- more follow up work from Chris register/unregister rework in various
places
- vgem dma-buf export (for writing testcases)
- small things all over from tons of different people
* tag 'topic/drm-misc-2016-07-14' of git://anongit.freedesktop.org/drm-intel: (52 commits)
drm: Don't overwrite user ioctl arg unless requested
dma-buf/sync_file: improve Kconfig description for Sync Files
MAINTAINERS: add entry for the Sync File Framework
drm: Resurrect atomic rmfb code
drm/vgem: Use PAGE_KERNEL in place of x86-specific PAGE_KERNEL_IO
qxl: silence uninitialized variable warning
qxl: check for kmap failures
vga_switcheroo: Sphinxify docs
drm: Restore double clflush on the last partial cacheline
gpu: drm: rockchip_drm_drv: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_vtg: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_hqvdp: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_vdo: add missing of_node_put after calling of_parse_phandle
gpu: drm: sti_compositor: add missing of_node_put after calling of_parse_phandle
drm/tilcdc: use drm_crtc_handle_vblank()
drm/rcar-du: use drm_crtc_handle_vblank()
drm/nouveau: use drm_crtc_handle_vblank()
drm/atmel: use drm_crtc_handle_vblank()
drm/armada: use drm_crtc_handle_vblank()
drm: make drm_vblank_count_and_time() static
...
Eric Anholt [Fri, 1 Jul 2016 20:10:38 +0000 (13:10 -0700)]
drm/vc4: Add a getparam ioctl for getting the V3D identity regs.
As I extend the driver to support different V3D revisions, userspace
needs to know what version it's targeting. This is most easily
detected using the V3D identity registers.
v2: Make sure V3D is runtime PM on when reading the registers.
v3: Switch to a 64-bit param value (suggested by Rob Clark in review)
Signed-off-by: Eric Anholt <eric@anholt.net> Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2) Reviewed-by: Rob Clark <robdclark@gmail.com> (v3, over irc)
Jon Hunter [Fri, 1 Jul 2016 13:21:38 +0000 (14:21 +0100)]
drm/tegra: sor: Prepare for generic PM domain support
The SOR driver for Tegra requires the SOR power partition to be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework. However, the sequence for
gating/ungating the SOR power partition requires that the SOR reset is
asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the SOR
driver cannot request the same reset unless we mark the reset as shared.
Sharing resets will not work in this case because we cannot guarantee
that the reset will be asserted/de-asserted at the appropriate time.
Therefore, given that the Tegra generic PM domain code will handle the
resets, do not request the reset in the SOR driver if the SOR device has
a PM domain associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Jon Hunter [Fri, 1 Jul 2016 13:21:37 +0000 (14:21 +0100)]
drm/tegra: dsi: Prepare for generic PM domain support
The DSI driver for Tegra requires the SOR power partition to be enabled.
Now that Tegra supports the generic PM domain framework we manage the
SOR power partition via this framework. However, the sequence for
gating/ungating the SOR power partition requires that the DSI reset is
asserted/de-asserted at the time the SOR power partition is
gated/ungated, respectively. Now that the reset control core assumes
that resets are exclusive, the Tegra generic PM domain code and the DSI
driver cannot request the same reset unless we mark the reset as shared.
Sharing resets will not work in this case because we cannot guarantee
that the reset will be asserted/de-asserted at the appropriate time.
Therefore, given that the Tegra generic PM domain code will handle the
resets, do not request the reset in the DSI driver if the DSI device has
a PM domain associated.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 9 Jun 2016 15:53:57 +0000 (17:53 +0200)]
drm/tegra: sor: Use sor1_src clock to set parent for HDMI
When running in HDMI mode, the sor1 IP block needs to use the sor1_src
as parent clock, and in turn configure the sor1_src to use pll_d2_out0
as its parent.
Thierry Reding [Thu, 23 Jun 2016 10:04:24 +0000 (12:04 +0200)]
dt-bindings: display: tegra: Add source clock for SOR
The SOR clock can have various sources, with the most commonly used
being the sor_safe, pll_d2_out0, pll_dp and sor_brick clocks. These
are configured using a three level mux, of which the first 2 levels
can be treated as one. The direct parents of the SOR clock are the
sor_safe, sor_brick and sor_src clocks, whereas the pll_d2_out0 and
pll_dp clocks can be selected as parents of the sor_src clock via a
second mux.
Previous generations of Tegra have only supported eDP and LVDS with
the SOR, where LVDS was never used on publicly available hardware.
Clocking for this only ever required the first level mux (to select
between sor_safe and sor_brick).
Tegra210 has a new revision of the SOR that supports HDMI and hence
needs to support the second level mux to allow selecting pll_d2_out0
as the SOR clock's parent. This second mux is knows as sor_src, and
operating system software needs a reference to it in order to select
the proper parent.
Thierry Reding [Thu, 1 Oct 2015 12:25:03 +0000 (14:25 +0200)]
drm/tegra: sor: Implement sor1_brick clock
sor1_brick is a clock that can be used as a source for the sor1 clock.
The registers to control the clock output are part of the sor1 IP block
and hence the sor driver is the best place to implement it.
Chris Wilson [Tue, 12 Jul 2016 14:59:50 +0000 (15:59 +0100)]
drm: Don't overwrite user ioctl arg unless requested
Currently, we completely ignore the user when it comes to the in/out
direction of the ioctl argument, as we simply cannot trust userspace.
(For example, they might request a copy of the modified ioctl argument
when the driver is not expecting such and so leak kernel stack.)
However, blindly copying over the target address may also lead to a
spurious EFAULT, and a failure after the ioctl was completed
successfully. This is important in order to avoid an ABI break when
extending an ioctl from IOR to IORW. Similar to how we only copy the
intersection of the kernel arg size and the user arg size, we only want
to copy back the kernel arg data iff both the kernel and userspace
request the copy.
Dave Airlie [Thu, 14 Jul 2016 02:14:49 +0000 (12:14 +1000)]
Merge branch 'linux-4.8' of git://github.com/skeggsb/linux into drm-next
Here's an initial drm-next pull for nouveau 4.8, highlights:
- GK20A/GM20B volt and clock improvements.
- Initial support for GP100/GP104 GPUs, GP104 will not yet support
acceleration due to NVIDIA having not released firmware for them as of yet.
* 'linux-4.8' of git://github.com/skeggsb/linux: (97 commits)
drm/nouveau/bus: remove cpu_coherent flag
drm/nouveau/ttm: remove special handling of coherent objects
drm/nouveau: check for supported chipset before booting fbdev off the hw
drm/nouveau/ce/gp104: initial support
drm/nouveau/fifo/gp104: initial support
drm/nouveau/disp/gp104: initial support
drm/nouveau/dma/gp104: initial support
drm/nouveau/ltc/gp104: initial support
drm/nouveau/ibus/gp104: initial support
drm/nouveau/i2c/gp104: initial support
drm/nouveau/gpio/gp104: initial support
drm/nouveau/fuse/gp104: initial support
drm/nouveau/bus/gp104: initial support
drm/nouveau/bar/gp104: initial support
drm/nouveau/mmu/gp104: initial support
drm/nouveau/fb/gp104: initial support
drm/nouveau/imem/gp104: initial support
drm/nouveau/devinit/gp104: initial support
drm/nouveau/bios/gp104: initial support
drm/nouveau/tmr/gp104: initial support
...
This flag's only remaining function is to ignore the uncached flag for
BOs on coherent architectures.
However the reason for allocating an object uncache on a non-coherent
architecture (namely because the cost of doing explicit flushes/
invalidations is higher than the benefit of caching the data because
accesses are few and far between) should also apply on architectures for
which coherency is maintained implicitly. Thus allocate coherent objects
as uncached on all architectures.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
drm/nouveau/ttm: remove special handling of coherent objects
TTM-allocated coherent objects were populated using the DMA API and
accessed using the mapping it returned to workaround coherency
issues. These issues seem to have been solved, thus remove this extra
case to handle and use the regular kernel mapping functions.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Ben Skeggs [Sat, 9 Jul 2016 00:41:01 +0000 (10:41 +1000)]
drm/nouveau/ltc/gp100: initial support
Due to the GPU preventing us from touching NV_PLTCG_LTCS_LTSS_CBC_BASE,
we cannot provide CBC/ZBC support without signed PMU firmware to handle
the task for us...
Ben Skeggs [Sat, 9 Jul 2016 00:41:01 +0000 (10:41 +1000)]
drm/nouveau/fb/gf100-: allow selection of an alternate big page size
GFxxx/GM1xx support the selection of 64/128KiB big pages globally.
GM2xx supports the same, as well as another mode where the page size
can be selected per-instance.
We default to 128KiB pages (With per-instance for GM200, but the current
code selects 128KiB there already) as the MMU code isn't currently able
to handle otherwise.
Ben Skeggs [Tue, 21 Jun 2016 06:29:03 +0000 (16:29 +1000)]
drm/nouveau/disp/nv50-: fix lookup of udisp table under certain circumstances
Some VBIOS have separate tables for each link of a given output path,
which means we have to specify the specific link we're using instead
of all possible links.
drm/nouveau/secboot: lazy-load firmware and be more resilient
Defer the loading of firmware files to the chip-specific part of secure
boot. This allows implementations to retry loading firmware if the first
attempt failed ; for the GM200 implementation, this happens when trying
to reset a falcon, typically in reaction to GR init.
Firmware loading may fail for a variety of reasons, such as the
filesystem where they reside not being ready at init time. This new
behavior allows GR to be initialized the next time we try to use it if
the firmware has become available.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
drm/nouveau/secboot/gm200: make firmware loading re-callable
Make it possible to call gm20x_secboot_prepare_blobs() several times
after either success or failure without re-building already existing
blobs. The function will now try to load firmware files that have
previously failed before returning success.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Handle and propagate secure boot errors. Failure to do so results in
Nouveau incorrectly believing init has succeeded and a completely
black display during boot. If we propagate the error, GR init will fail
and the user will at least have a working display.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Karol Herbst [Fri, 26 Feb 2016 06:49:08 +0000 (07:49 +0100)]
drm/nouveau/volt: save the voltage range we are able to set
We shouldn't set voltages below the min or above the max voltage the gpu is
able to set, so save the range for future lookups.
Signed-off-by: Karol Herbst <karolherbst@gmail.de> Reviewed-by: Martin Peres <martin.peres@free.fr> Tested-by: Pierre Moreau <pierre.morrow@free.fr> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
drm/nouveau/clk/gm20b: add glitchless and DFS support
This patch adds support for advanced features supported by the
Noise-Aware PLL of Maxwell. Glitchless switch allows the PL field to be
updated without disabling the PLL first if the SYNC_MODE bit of the CFG
register is set.
More significantly, DFS allows the PLL to monitor the actual input
voltage and to dynamically lower the output frequency accordingly. This
allows the clock to be more tolerant of lower voltages.
These improvements are only supported for Tegra speedos >= 1.
Also add the voltage table that is suitable for GM20B's NAPLL. This
change needs to be done atomically for the right voltages to be used by
the clock driver.
v2. Fix build on non-Tegra platforms
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Split the MNP programming function into two functions for the cases
where we allow sliding or not, instead of making it take a parameter for
this. This results in less conditionals in the code and makes it easier
to read.
Also make the MNP programming functions take the PLL parameters as
arguments, and move bits of code to more relevant places (previous
programming tended to be just-in-time, which added more conditionnals in
the code).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
projects / linux-beck.git / log