Jingoo Han [Thu, 10 Oct 2013 07:40:58 +0000 (16:40 +0900)]
ARM: SAMSUNG: Remove unused s5p_device_ehci
Since commit ca91435 "ARM: EXYNOS: Remove unused board files",
s5p_device_ehci is not used anymore. Thus, s5p_device_ehci can
be removed. Also, unnecessary S5P_DEV_USB_EHCI option is removed.
Alan Stern [Fri, 11 Oct 2013 15:29:22 +0000 (11:29 -0400)]
USB: add a private-data pointer to struct usb_tt
For improved scheduling of transfers through a Transaction Translator,
ehci-hcd will need to store a bunch of information associated with the
FS/LS bus on the downstream side of the TT. This patch adds a pointer
for such HCD-private data to the usb_tt structure.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 11 Oct 2013 15:29:13 +0000 (11:29 -0400)]
USB: EHCI: use a bandwidth-allocation table
This patch significantly changes the scheduling code in ehci-hcd.
Instead of calculating the current bandwidth utilization by trudging
through the schedule and adding up the times used by the existing
transfers, we will now maintain a table holding the time used for each
of 64 microframes. This will drastically speed up the bandwidth
computations.
In addition, it eliminates a theoretical bug. An isochronous endpoint
may have bandwidth reserved even at times when it has no transfers
listed in the schedule. The table will keep track of the reserved
bandwidth, whereas adding up entries in the schedule would miss it.
As a corollary, we can keep bandwidth reserved for endpoints even
when they aren't in active use. Eventually the bandwidth will be
reserved when a new alternate setting is installed; for now the
endpoint's reservation takes place when its first URB is submitted.
A drawback of this approach is that transfers with an interval larger
than 64 microframes will have to be charged for bandwidth as though
the interval was 64. In practice this shouldn't matter much;
transfers with longer intervals tend to be rather short anyway (things
like hubs or HID devices).
Another minor drawback is that we will keep track of two different
period and phase values: the actual ones and the ones used for
bandwidth allocation (which are limited to 64). This adds only a
small amount of overhead: 3 bytes for each endpoint.
The patch also adds a new debugfs file named "bandwidth" to display
the information stored in the new table.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 11 Oct 2013 15:29:03 +0000 (11:29 -0400)]
USB: EHCI: create a "periodic schedule info" struct
This patch begins the process of unifying the scheduling parameters
that ehci-hcd uses for interrupt and isochronous transfers. It
creates an ehci_per_sched structure, which will be stored in both
ehci_qh and ehci_iso_stream structures, and will contain the common
scheduling information needed for both.
Initially we merely create the new structure and move some existing
fields into it. Later patches will add more fields and utilize these
structures in improved scheduling algorithms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 11 Oct 2013 15:28:52 +0000 (11:28 -0400)]
USB: EHCI: use consistent NO_FRAME value
ehci-hcd is inconsistent in the sentinel values it uses to indicate
that no frame number has been assigned for a periodic transfer. Some
places it uses NO_FRAME (defined as 65535), other places it uses -1,
and elsewhere it uses 9999.
This patch defines a value for NO_FRAME which can fit in a 16-bit
signed integer, and changes the code to use it everywhere.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 11 Oct 2013 15:28:44 +0000 (11:28 -0400)]
USB: EHCI: change toggle only upon successful reset
ehci-hcd uses a value of 0 in an endpoint's toggle flag to indicate
that the endpoint has been reset (and therefore the Data Toggle bit
needs to be cleared in the endpoint's QH overlay region).
The toggle flag should be set to 0 only when ehci_endpoint_reset()
succeeds. This patch moves the usb_settoggle() call into the
appropriate branch of the "if" statement.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 11 Oct 2013 15:28:31 +0000 (11:28 -0400)]
USB: EHCI: No SSPLIT allowed in uframe 7
The scheduling code in ehci-hcd contains an error. For full-speed
isochronous-OUT transfers, the EHCI spec forbids scheduling
Start-Split transactions in H-microframe 7, but the driver allows it
anyway. This patch adds a check to prevent it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the bandwidth statistics maintained by ehci-hcd show up only
in the /sys/kernel/debug/usb/devices file, they ought to be calculated
correctly. The calculation for full-speed isochronous endpoints is
wrong; it mistakenly yields bytes per microframe instead of bytes per
frame. The "interval" value, which is in frames, should not be
converted to microframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 11 Oct 2013 15:28:12 +0000 (11:28 -0400)]
USB: EHCI: check the right uframes for CSPLIT
The check_intr_schedule() routine in ehci-hcd looks at the wrong
microframes when checking to see if a full-speed or low-speed
interrupt endpoint will fit in the periodic schedule. If the
Start-Split transaction is scheduled for microframe N then the
Complete-Split transactions get scheduled for microframes N+2, N+3, and
N+4. However the code considers N+1, N+2, and N+3 instead.
This patch fixes the limits on the "for" loop and also improves the
use of whitespace.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 11 Oct 2013 15:28:02 +0000 (11:28 -0400)]
USB: NS_TO_US should round up
Host controller drivers use the NS_TO_US macro to convert transaction
times, which are computed in nanoseconds, to microseconds for
scheduling. Periodic scheduling requires worst-case estimates, but
the macro does its conversion using round-to-nearest. This patch
changes it to use round-up, giving a correct worst-case value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Wed, 9 Oct 2013 15:01:41 +0000 (17:01 +0200)]
usb-anchor: Delay usb_wait_anchor_empty_timeout wake up till completion is done
usb_wait_anchor_empty_timeout() should wait till the completion handler
has run. Both the zd1211rw driver and the uas driver (in its task mgmt) depend
on the completion handler having completed when usb_wait_anchor_empty_timeout()
returns, as they read state set by the completion handler after an
usb_wait_anchor_empty_timeout() call.
But __usb_hcd_giveback_urb() calls usb_unanchor_urb before calling the
completion handler. This is necessary as the completion handler may
re-submit and re-anchor the urb. But this introduces a race where the state
these drivers want to read has not been set yet by the completion handler
(this race is easily triggered with the uas task mgmt code).
I've considered adding an anchor_count to struct urb, which would be
incremented on anchor and decremented on unanchor, and then only actually
do the anchor / unanchor on 0 -> 1 and 1 -> 0 transtions, combined with
moving the unanchor call in hcd_giveback_urb to after calling the completion
handler. But this will only work if urb's are only re-anchored to the same
anchor as they were anchored to before the completion handler ran.
And at least one driver re-anchors to another anchor from the completion
handler (rtlwifi).
So I have come up with this patch instead, which adds the ability to
suspend wakeups of usb_wait_anchor_empty_timeout() waiters to the usb_anchor
functionality, and uses this in __usb_hcd_giveback_urb() to delay wake-ups
until the completion handler has run.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Wed, 9 Oct 2013 15:01:40 +0000 (17:01 +0200)]
usb-anchor: Ensure poisened gets initialized to 0
And do so in a way which ensures that any fields added in the future will
also get properly zero-ed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Oliver Neukum <oliver@neukum.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ivan T. Ivanov [Fri, 11 Oct 2013 11:46:10 +0000 (14:46 +0300)]
USB: ehci-msm: Add device tree support and binding information
Allows MSM EHCI controller to be specified via device tree.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Acked-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ivan T. Ivanov [Fri, 11 Oct 2013 11:46:09 +0000 (14:46 +0300)]
ehci-msm: Remove global struct usb_phy variable
Use struct usb_hcd::phy to hold USB PHY instance.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com> Acked-by: David Brown <davidb@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Wed, 9 Oct 2013 06:39:52 +0000 (14:39 +0800)]
usb: chipidea: udc: Fix spinlock recursion during bus reset
After configuration, the host also possible sends bus reset
at any time, at such situation, it will trigger below spinlock
recursion dump. This commit unlocks the spinlock before calling
gadget's disconnect.
BUG: spinlock recursion on CPU#0, swapper/0/0
lock: 0xbf128014, .magic: dead4ead, .owner: swapper/0/0, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-next-20130910+ #106
[<80014e20>] (unwind_backtrace+0x0/0xec) from [<80011a6c>] (show_stack+0x10/0x14)
[<80011a6c>] (show_stack+0x10/0x14) from [<805c143c>] (dump_stack+0x94/0xbc)
[<805c143c>] (dump_stack+0x94/0xbc) from [<80282cf8>] (do_raw_spin_lock+0x16c/0x18c)
[<80282cf8>] (do_raw_spin_lock+0x16c/0x18c) from [<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c)
[<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c) from [<803cff88>] (ep_disable+0x24/0x110)
[<803cff88>] (ep_disable+0x24/0x110) from [<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial])
[<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial]) from [<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm])
[<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm]) from [<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite])
[<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite]) from [<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite])
[<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite]) from [<803d1024>] (udc_irq+0x770/0xce4)
[<803d1024>] (udc_irq+0x770/0xce4) from [<803cdcc0>] (ci_irq+0x98/0x164)
[<803cdcc0>] (ci_irq+0x98/0x164) from [<8007edfc>] (handle_irq_event_percpu+0x50/0x17c)
[<8007edfc>] (handle_irq_event_percpu+0x50/0x17c) from [<8007ef64>] (handle_irq_event+0x3c/0x5c)
[<8007ef64>] (handle_irq_event+0x3c/0x5c) from [<80081e98>] (handle_fasteoi_irq+0x98/0x168)
[<80081e98>] (handle_fasteoi_irq+0x98/0x168) from [<8007e598>] (generic_handle_irq+0x28/0x3c)
[<8007e598>] (generic_handle_irq+0x28/0x3c) from [<8000edf4>] (handle_IRQ+0x4c/0xb4)
[<8000edf4>] (handle_IRQ+0x4c/0xb4) from [<800085bc>] (gic_handle_irq+0x28/0x5c)
[<800085bc>] (gic_handle_irq+0x28/0x5c) from [<800125c0>] (__irq_svc+0x40/0x54)
Exception stack(0x8083bf68 to 0x8083bfb0)
bf60: 81533b8000000000000962348001d7608088e12c00000000
bf80: 8083a0008083a0008084290c805cb414808428ac8083a000000000018083bfb0
bfa0: 8000f1388000f13c60000013ffffffff
[<800125c0>] (__irq_svc+0x40/0x54) from [<8000f13c>] (arch_cpu_idle+0x30/0x3c)
[<8000f13c>] (arch_cpu_idle+0x30/0x3c) from [<8005eb94>] (cpu_startup_entry+0xf4/0x148)
[<8005eb94>] (cpu_startup_entry+0xf4/0x148) from [<807f1a2c>] (start_kernel+0x2c4/0x318)
BUG: spinlock lockup suspected on CPU#0, swapper/0/0
lock: 0xbf128014, .magic: dead4ead, .owner: swapper/0/0, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-next-20130910+ #106
[<80014e20>] (unwind_backtrace+0x0/0xec) from [<80011a6c>] (show_stack+0x10/0x14)
[<80011a6c>] (show_stack+0x10/0x14) from [<805c143c>] (dump_stack+0x94/0xbc)
[<805c143c>] (dump_stack+0x94/0xbc) from [<80282c94>] (do_raw_spin_lock+0x108/0x18c)
[<80282c94>] (do_raw_spin_lock+0x108/0x18c) from [<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c)
[<805c77e0>] (_raw_spin_lock_irqsave+0x50/0x5c) from [<803cff88>] (ep_disable+0x24/0x110)
[<803cff88>] (ep_disable+0x24/0x110) from [<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial])
[<7f015d50>] (gserial_disconnect+0xa0/0x15c [u_serial]) from [<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm])
[<7f01c06c>] (acm_disable+0xc/0x30 [usb_f_acm]) from [<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite])
[<7f001478>] (reset_config.isra.10+0x34/0x5c [libcomposite]) from [<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite])
[<7f0014d4>] (composite_disconnect+0x34/0x5c [libcomposite]) from [<803d1024>] (udc_irq+0x770/0xce4)
[<803d1024>] (udc_irq+0x770/0xce4) from [<803cdcc0>] (ci_irq+0x98/0x164)
[<803cdcc0>] (ci_irq+0x98/0x164) from [<8007edfc>] (handle_irq_event_percpu+0x50/0x17c)
[<8007edfc>] (handle_irq_event_percpu+0x50/0x17c) from [<8007ef64>] (handle_irq_event+0x3c/0x5c)
[<8007ef64>] (handle_irq_event+0x3c/0x5c) from [<80081e98>] (handle_fasteoi_irq+0x98/0x168)
[<80081e98>] (handle_fasteoi_irq+0x98/0x168) from [<8007e598>] (generic_handle_irq+0x28/0x3c)
[<8007e598>] (generic_handle_irq+0x28/0x3c) from [<8000edf4>] (handle_IRQ+0x4c/0xb4)
[<8000edf4>] (handle_IRQ+0x4c/0xb4) from [<800085bc>] (gic_handle_irq+0x28/0x5c)
[<800085bc>] (gic_handle_irq+0x28/0x5c) from [<800125c0>] (__irq_svc+0x40/0x54)
Exception stack(0x8083bf68 to 0x8083bfb0)
bf60: 81533b8000000000000962348001d7608088e12c00000000
bf80: 8083a0008083a0008084290c805cb414808428ac8083a000000000018083bfb0
bfa0: 8000f1388000f13c60000013ffffffff
[<800125c0>] (__irq_svc+0x40/0x54) from [<8000f13c>] (arch_cpu_idle+0x30/0x3c)
[<8000f13c>] (arch_cpu_idle+0x30/0x3c) from [<8005eb94>] (cpu_startup_entry+0xf4/0x148)
[<8005eb94>] (cpu_startup_entry+0xf4/0x148) from [<807f1a2c>] (start_kernel+0x2c4/0x318)
Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deng-Cheng Zhu [Sun, 6 Oct 2013 06:08:17 +0000 (23:08 -0700)]
USB/host: Bugfix: Return length of copied buffer in uhci_hub_control()
In addition to the error statuses -ETIMEDOUT and -EPIPE, uhci_hub_control()
needs to return the length of copied buffer when appropriate, so that the
returned status of ->hub_control() in rh_call_control() in the USB core
HCD can be properly handled.
This patch also removes the OK() macro to make the code more readable.
Reviewed-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target fixes queued up for v3.12-rc4 code.
The highlights include:
- Make vhost/scsi tag percpu_ida_alloc() use GFP_ATOMIC
- Allow sess_cmd_map allocation failure fallback to use vzalloc
- Fix COMPARE_AND_WRITE se_cmd->data_length bug with FILEIO backends
- Fixes for COMPARE_AND_WRITE callback recursive failure OOPs + non
zero scsi_status bug
- Make iscsi-target do acknowledgement tag release from RX context
- Setup iscsi-target with extra (cmdsn_depth / 2) percpu_ida tags
Also included is a iscsi-target patch CC'ed for v3.10+ that avoids
legacy wait_for_task=true release during fast-past StatSN
acknowledgement, and two other SRP target related patches that address
long-standing issues that are CC'ed for v3.3+.
Extra thanks to Thomas Glanzmann for his testing feedback with
COMPARE_AND_WRITE + EXTENDED_COPY VAAI logic"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
iscsi-target: Perform release of acknowledged tags from RX context
iscsi-target: Only perform wait_for_tasks when performing shutdown
target: Fail on non zero scsi_status in compare_and_write_callback
target: Fix recursive COMPARE_AND_WRITE callback failure
target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
ib_srpt: always set response for task management
target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
ib_srpt: Destroy cm_id before destroying QP.
target: Fix xop->dbl assignment in target_xcopy_parse_segdesc_02
Linus Torvalds [Sun, 6 Oct 2013 20:35:15 +0000 (13:35 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the slave dmanegine fixes. We have the fix for deadlock issue
on imx-dma by Michael and Josh's edma config fix along with author
change"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: imx-dma: fix callback path in tasklet
dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
dma/Kconfig: Make TI_EDMA select TI_PRIV_EDMA
edma: Update author email address
Suspend scenario in case of ohci-spear glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-spear suspend scenario.
Calling explicitly the ohci_suspend() routine in
spear_ohci_hcd_drv_suspend() will ensure proper
handling of suspend scenario.
Suspend scenario in case of ohci-sm501 glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly
handle ohci-sm501 suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_sm501_suspend() will ensure proper handling of suspend
scenario.
Suspend scenario in case of ohci-pxa27x glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly
handle ohci-pxa27x suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_hcd_pxa27x_drv_suspend() will ensure proper
handling of suspend scenario.
Suspend scenario in case of ohci-platform glue was not
properly handled as it was not suspending generic part
of ohci controller.Alan Stern suggested, properly handle
ohci-platform suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_platform_suspend() will ensure proper handling of
suspend scenario.
Suspend scenario in case of ohci-omap glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-omap suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_omap_suspend() will ensure proper handling of suspend
scenario.
Suspend scenario in case of ohci-exynos glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-exynos suspend scenario.
Calling explicitly the ohci_suspend() routine in
exynos_ohci_suspend() will ensure proper handling of suspend
scenario.
Suspend scenario in case of ohci-ep93xx glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-ep93xx suspend scenario.
Calling explicitly the ohci_suspend() routine in
ohci_hcd_ep93xx_drv_suspend() will ensure proper handling of
suspend scenario.
Suspend scenario in case of ohci-da8xx glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-da8xx suspend scenario.
Calling explicitly the ohci_suspend()
routine in ohci_da8xx_suspend() will ensure proper
handling of suspend scenario.
Suspend scenario in case of ohci-s3c2410 glue was not
properly handled as it was not suspending generic part
of ohci controller. Alan Stern suggested, properly handle
ohci-s3c2410 suspend scenario.
Calling explicitly the ohci_suspend()
routine in ohci_hcd_s3c2410_drv_suspend() will ensure
proper handling of suspend scenario.
Suspend scenario in case of ohci-at91 glue was not properly handled
as it was not suspending generic part of ohci controller. Alan Stern
suggested, properly handle ohci-at91 suspend scenario.
Calling explicitly the ohci_suspend() routine in ohci_hcd_at91_drv_suspend()
will ensure proper handling of suspend scenario. This task is sugested
by Alan Stern.
David Cohen [Fri, 4 Oct 2013 22:30:21 +0000 (15:30 -0700)]
usb: g_ffs: fix compilation warning
If USB_FUNCTIONFS is selected without USB_FUNCTIONFS_ETH and
USB_FUNCTIONFS_RNIS, u_ether.h won't be included and then
USB_ETHERNET_MODULE_PARAMAETERS macro won't be available causing the
following warning compilation:
drivers/usb/gadget/g_ffs.c:81:1: warning: data definition has no type or
storage class [enabled by default]
drivers/usb/gadget/g_ffs.c:81:1: warning: type defaults to ‘int’ in
declaration of ‘USB_ETHERNET_MODULE_PARAMETERS’ [-Wimplicit-int]
drivers/usb/gadget/g_ffs.c:81:1: warning: function declaration isn’t a
prototype [-Wstrict-prototypes]
This patch fixes the warning by making USB_ETHERNET_MODULE_PARAMETERS to
be used iff u_ether.h is included, otherwise it is not needed.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Pugliese [Fri, 4 Oct 2013 15:40:45 +0000 (10:40 -0500)]
usb: wusbcore: add support for isoc out transfers
This patch adds support for isochronous out transfers to the HWA. The
primary changes are:
1. Add a isoc_pack_desc_urb field to struct wa_seg. This urb is used
to send the isochronous packet info message to the HWA which describes
the isoc data segment(s) that will be sent as the payload of the
transfer request.
2. Use the URB iso_frame_desc field to populate the isochronous packet
info message and data segments sent to the HWA.
3. After the data is sent and transfer result is returned from the
HWA, read the isoc packet status message from the HWA. The contents of
the isoc packet status message are used to set the iso_frame_desc
status and actual_length fields in the original isoc URB. This feature
required the addition of a some state tracking variables in struct wahc
so the dti_urb knows what type of packet it expects to receive next.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 5 Oct 2013 19:17:24 +0000 (12:17 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"This is a small collection of fixes, including a regression fix from
Liu Bo that solves rare crashes with compression on.
I've merged my for-linus up to 3.12-rc3 because the top commit is only
meant for 3.12. The rest of the fixes are also available in my master
branch on top of my last 3.11 based pull"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: Fix crash due to not allocating integrity data for a bioset
Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
Btrfs: eliminate races in worker stopping code
Btrfs: fix crash of compressed writes
Btrfs: fix transid verify errors when recovering log tree
Linus Torvalds [Sat, 5 Oct 2013 19:11:40 +0000 (12:11 -0700)]
Merge tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two patches for the OMAP driver, dealing with setting up IRQs properly
on the device tree boot path"
* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/omap: auto-setup a GPIO when used as an IRQ
gpio/omap: maintain GPIO and IRQ usage separately
Linus Torvalds [Sat, 5 Oct 2013 18:54:10 +0000 (11:54 -0700)]
Merge tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are none fixes for various USB driver problems. The majority are
gadget/musb fixes, but there are some new device ids in here as well"
* tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: add Intel Clovertrail pci id
usb: gadget: s3c-hsotg: fix can_write limit for non-periodic endpoints
usb: gadget: f_fs: fix error handling
usb: musb: dsps: do not bind to "musb-hdrc"
USB: serial: option: Ignore card reader interface on Huawei E1750
usb: musb: gadget: fix otg active status flag
usb: phy: gpio-vbus: fix deferred probe from __init
usb: gadget: pxa25x_udc: fix deferred probe from __init
usb: musb: fix otg default state
Linus Torvalds [Sat, 5 Oct 2013 18:26:19 +0000 (11:26 -0700)]
Merge tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fixes from Greg KH:
"Here are two tty driver fixes for 3.12-rc4.
One fixes the reported regression in the n_tty code that a number of
people found recently, and the other one fixes an issue with xen
consoles that broke in 3.10"
* tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
xen/hvc: allow xenboot console to be used again
tty: Fix pty master read() after slave closes
Darrick J. Wong [Fri, 20 Sep 2013 03:37:07 +0000 (20:37 -0700)]
btrfs: Fix crash due to not allocating integrity data for a bioset
When btrfs creates a bioset, we must also allocate the integrity data pool.
Otherwise btrfs will crash when it tries to submit a bio to a checksumming
disk:
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com> Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Linus Torvalds [Sat, 5 Oct 2013 03:50:16 +0000 (20:50 -0700)]
Merge branch 'for-linus' of git://git.samba.org/sfrench/cifs-2.6
Pull CIFS fixes from Steve French:
"Small set of cifs fixes. Most important is Jeff's fix that works
around disconnection problems which can be caused by simultaneous use
of user space tools (starting a long running smbclient backup then
doing a cifs kernel mount) or multiple cifs mounts through a NAT, and
Jim's fix to deal with reexport of cifs share.
I expect to send two more cifs fixes next week (being tested now) -
fixes to address an SMB2 unmount hang when server dies and a fix for
cifs symlink handling of Windows "NFS" symlinks"
* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
[CIFS] update cifs.ko version
[CIFS] Remove ext2 flags that have been moved to fs.h
[CIFS] Provide sane values for nlink
cifs: stop trying to use virtual circuits
CIFS: FS-Cache: Uncache unread pages in cifs_readpages() before freeing them
Linus Torvalds [Sat, 5 Oct 2013 03:48:20 +0000 (20:48 -0700)]
Merge tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"We merged what was intended to be an MMCONFIG cleanup, but in fact,
for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and it broke all config space for
other domains.
This reverts the change"
* tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "x86/PCI: MMCONFIG: Check earlier for MMCONFIG region at address zero"
07f9b61c was intended to be a cleanup that didn't change anything, but in
fact, for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and all config space for other domains.
Linus Torvalds [Fri, 4 Oct 2013 22:03:42 +0000 (15:03 -0700)]
Merge tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- The resume part of user space driven hibernation (s2disk) is now
broken after the change that moved the creation of memory bitmaps to
after the freezing of tasks, because I forgot that the resume utility
loaded the image before freezing tasks and needed the bitmaps for
that. The fix adds special handling for that case.
- One of recent commits changed the export of acpi_bus_get_device() to
EXPORT_SYMBOL_GPL(), which was technically correct but broke existing
binary modules using that function including one in particularly
widespread use. Change it back to EXPORT_SYMBOL().
- The intel_pstate driver sometimes fails to disable turbo if its
no_turbo sysfs attribute is set. Fix from Srinivas Pandruvada.
- One of recent cpufreq fixes forgot to update a check in cpufreq-cpu0
which still (incorrectly) treats non-NULL as non-error. Fix from
Philipp Zabel.
- The SPEAr cpufreq driver uses a wrong variable type in one place
preventing it from catching errors returned by one of the functions
called by it. Fix from Sachin Kamat.
* tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Use EXPORT_SYMBOL() for acpi_bus_get_device()
intel_pstate: fix no_turbo
cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
cpufreq: SPEAr: Fix incorrect variable type
PM / hibernate: Fix user space driven resume regression
Linus Torvalds [Fri, 4 Oct 2013 21:47:22 +0000 (14:47 -0700)]
Merge tag 'xfs-for-linus-v3.12-rc4' of git://oss.sgi.com/xfs/xfs
Pull xfs bugfixes from Ben Myers:
"There are lockdep annotations for project quotas, a fix for dirent
dtype support on v4 filesystems, a fix for a memory leak in recovery,
and a fix for the build error that resulted from it. D'oh"
* tag 'xfs-for-linus-v3.12-rc4' of git://oss.sgi.com/xfs/xfs:
xfs: Use kmem_free() instead of free()
xfs: fix memory leak in xlog_recover_add_to_trans
xfs: dirent dtype presence is dependent on directory magic numbers
xfs: lockdep needs to know about 3 dquot-deep nesting
Ilya Dryomov [Wed, 2 Oct 2013 17:41:01 +0000 (20:41 +0300)]
Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
free_device rcu callback, scheduled from btrfs_rm_dev_replace_srcdev,
can be processed before btrfs_scratch_superblock is called, which would
result in a use-after-free on btrfs_device contents. Fix this by
zeroing the superblock before the rcu callback is registered.
Cc: Stefan Behrens <sbehrens@giantdisaster.de> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Ilya Dryomov [Wed, 2 Oct 2013 16:39:50 +0000 (19:39 +0300)]
Btrfs: eliminate races in worker stopping code
The current implementation of worker threads in Btrfs has races in
worker stopping code, which cause all kinds of panics and lockups when
running btrfs/011 xfstest in a loop. The problem is that
btrfs_stop_workers is unsynchronized with respect to check_idle_worker,
check_busy_worker and __btrfs_start_workers.
E.g., check_idle_worker race flow:
btrfs_stop_workers(): check_idle_worker(aworker):
- grabs the lock
- splices the idle list into the
working list
- removes the first worker from the
working list
- releases the lock to wait for
its kthread's completion
- grabs the lock
- if aworker is on the working list,
moves aworker from the working list
to the idle list
- releases the lock
- grabs the lock
- puts the worker
- removes the second worker from the
working list
......
btrfs_stop_workers returns, aworker is on the idle list
FS is umounted, memory is freed
......
aworker is waken up, fireworks ensue
With this applied, I wasn't able to trigger the problem in 48 hours,
whereas previously I could reliably reproduce at least one of these
races within an hour.
Reported-by: David Sterba <dsterba@suse.cz> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Liu Bo [Tue, 1 Oct 2013 15:49:49 +0000 (23:49 +0800)]
Btrfs: fix crash of compressed writes
The crash[1] is found by xfstests/generic/208 with "-o compress",
it's not reproduced everytime, but it does panic.
The bug is quite interesting, it's actually introduced by a recent commit
(573aecafca1cf7a974231b759197a1aebcf39c2a,
Btrfs: actually limit the size of delalloc range).
Btrfs implements delay allocation, so during writeback, we
(1) get a page A and lock it
(2) search the state tree for delalloc bytes and lock all pages within the range
(3) process the delalloc range, including find disk space and create
ordered extent and so on.
(4) submit the page A.
It runs well in normal cases, but if we're in a racy case, eg.
buffered compressed writes and aio-dio writes,
sometimes we may fail to lock all pages in the 'delalloc' range,
in which case, we need to fall back to search the state tree again with
a smaller range limit(max_bytes = PAGE_CACHE_SIZE - offset).
The mentioned commit has a side effect, that is, in the fallback case,
we can find delalloc bytes before the index of the page we already have locked,
so we're in the case of (delalloc_end <= *start) and return with (found > 0).
This ends with not locking delalloc pages but making ->writepage still
process them, and the crash happens.
This fixes it by just thinking that we find nothing and returning to caller
as the caller knows how to deal with it properly.
Josef Bacik [Mon, 30 Sep 2013 18:10:43 +0000 (14:10 -0400)]
Btrfs: fix transid verify errors when recovering log tree
If we crash with a log, remount and recover that log, and then crash before we
can commit another transaction we will get transid verify errors on the next
mount. This is because we were not zero'ing out the log when we committed the
transaction after recovery. This is ok as long as we commit another transaction
at some point in the future, but if you abort or something else goes wrong you
can end up in this weird state because the recovery stuff says that the tree log
should have a generation+1 of the super generation, which won't be the case of
the transaction that was started for recovery. Fix this by removing the check
and _always_ zero out the log portion of the super when we commit a transaction.
This fixes the transid verify issues I was seeing with my force errors tests.
Thanks,
Linus Torvalds [Fri, 4 Oct 2013 19:54:11 +0000 (12:54 -0700)]
selinux: remove 'flags' parameter from inode_has_perm
Every single user passes in '0'. I think we had non-zero users back in
some stone age when selinux_inode_permission() was implemented in terms
of inode_has_perm(), but that complicated case got split up into a
totally separate code-path so that we could optimize the much simpler
special cases.
See commit 2e33405785d3 ("SELinux: delay initialization of audit data in
selinux_inode_permission") for example.
Free the memory in error path of xlog_recover_add_to_trans().
Normally this memory is freed in recovery pass2, but is leaked
in the error path.
Signed-off-by: Mark Tinguely <tinguely@sgi.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 519ccb81ac1c8e3e4eed294acf93be00b43dcad6)
Dave Chinner [Sun, 29 Sep 2013 23:37:04 +0000 (09:37 +1000)]
xfs: dirent dtype presence is dependent on directory magic numbers
The determination of whether a directory entry contains a dtype
field originally was dependent on the filesystem having CRCs
enabled. This meant that the format for dtype beign enabled could be
determined by checking the directory block magic number rather than
doing a feature bit check. This was useful in that it meant that we
didn't need to pass a struct xfs_mount around to functions that
were already supplied with a directory block header.
Unfortunately, the introduction of dtype fields into the v4
structure via a feature bit meant this "use the directory block
magic number" method of discriminating the dirent entry sizes is
broken. Hence we need to convert the places that use magic number
checks to use feature bit checks so that they work correctly and not
by chance.
The current code works on v4 filesystems only because the dirent
size roundup covers the extra byte needed by the dtype field in the
places where this problem occurs.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 367993e7c6428cb7617ab7653d61dca54e2fdede)
The lockdep annotation for dquot lock nesting only understands
locking for user and "other" dquots, not user, group and quota
dquots. Fix the annotations to match the locking heirarchy we now
have.
Reported-by: Michael L. Semon <mlsemon35@gmail.com> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Ben Myers <bpm@sgi.com> Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit f112a049712a5c07de25d511c3c6587a2b1a015e)
Linus Torvalds [Fri, 4 Oct 2013 16:06:13 +0000 (09:06 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse bugfixes from Miklos Szeredi:
"This contains two more fixes by Maxim for writeback/truncate races and
fixes for RCU walk in fuse_dentry_revalidate()"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: no RCU mode in fuse_access()
fuse: readdirplus: fix RCU walk
fuse: don't check_submounts_and_drop() in RCU walk
fuse: fix fallocate vs. ftruncate race
fuse: wait for writeback in fuse_file_fallocate()
Linus Torvalds [Fri, 4 Oct 2013 16:05:12 +0000 (09:05 -0700)]
Merge tag 'iommu-fixes-v3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"A couple of fixes from the IOMMU side:
- some small fixes for the new ARM-SMMU driver
- a register offset correction for VT-d
- add MAINTAINERS entry for drivers/iommu
Overall no really big or intrusive changes"
* tag 'iommu-fixes-v3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
x86/iommu: correct ICS register offset
MAINTAINERS: add overall IOMMU section
iommu/arm-smmu: don't enable SMMU device until probing has completed
iommu/arm-smmu: fix iommu_present() test in init
iommu/arm-smmu: fix a signedness bug
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Remove duplicate DEBUG_STACK_USAGE config
arm64: include VIRTIO_{MMIO,BLK} in defconfig
arm64: include EXT4 in defconfig
arm64: fix possible invalid FPSIMD initialization state
arm64: use correct register width when retrieving ASID
arm64: avoid multiple evaluation of ptr in get_user/put_user()
Linus Torvalds [Fri, 4 Oct 2013 16:03:51 +0000 (09:03 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Two small fixes for 3.12 only this week. I have a few more fixes
pending but those are conceptually more complex so will have to wait
for a bit longer"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix forgotten preempt_enable() when CPU has inclusive pcaches
MIPS: Alchemy: MTX-1: fix incorrect placement of __initdata tag
Linus Torvalds [Fri, 4 Oct 2013 16:03:07 +0000 (09:03 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Two simplefb fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/simplefb: Mark framebuffer mem-resources as IORESOURCE_BUSY to avoid bootup warning
x86/simplefb: Fix overflow causing bogus fall-back
We need to free the ld_active list head before jumping into the callback
routine. Otherwise the callback could run into issue_pending and change
our ld_active list head we just going to free. This will run the channel
list into an currupted and undefined state.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
The tasklet and irqhandler are using spin_lock while other routines are
using spin_lock_irqsave/restore. This leads to lockdep issues as
described bellow. This patch is changing the code to use
spinlock_irq_save/restore in both code pathes.
As imxdma_xfer_desc always gets called with spin_lock_irqsave lock held,
this patch also removes the spare call inside the routine to avoid
double locking.
dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
When perparing cyclic_dma buffers by the sound layer, it will dump the
following lockdep trace. The leading snd_pcm_action_single get called
with read_lock_irq called. To fix this, we change the kcalloc call from
GFP_KERNEL to GFP_ATOMIC.
David Vrabel [Tue, 1 Oct 2013 18:00:49 +0000 (19:00 +0100)]
xen/hvc: allow xenboot console to be used again
Commit d0380e6c3c0f6edb986d8798a23acfaf33d5df23 (early_printk:
consolidate random copies of identical code) added in 3.10 introduced
a check for con->index == -1 in early_console_register().
Initialize index to -1 for the xenboot console so earlyprintk=xen
works again.
Roger Quadros [Thu, 3 Oct 2013 15:12:35 +0000 (18:12 +0300)]
usb: phy: omap: get rid of omap_get_control_dev()
This function was preventing us from supporting multiple
instances. Get rid of it. Since we support DT boots only,
users can get the control device phandle from the DT node.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Quadros [Thu, 3 Oct 2013 15:12:34 +0000 (18:12 +0300)]
usb: musb: omap2430: Don't use omap_get_control_dev()
omap_get_control_dev() is being deprecated as it doesn't support
multiple instances. As control device is present only from OMAP4
onwards which supports DT only, we use phandles to get the
reference to the control device.
Also get rid of "ti,has-mailbox" property as it is redundant and
we can determine that from whether "ctrl-module" property is present
or not. Get rid of has_mailbox from musb_hdrc_platform_data as well.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Quadros [Thu, 3 Oct 2013 15:12:33 +0000 (18:12 +0300)]
usb: phy: omap-usb3: Don't use omap_get_control_dev()
omap_get_control_dev() is being deprecated as it doesn't support
multiple instances. As control device is present only from OMAP4
onwards which supports DT only, we use phandles to get the
reference to the control device.
As we don't support non-DT boot, we just bail out on probe
if device node is not present.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Quadros [Thu, 3 Oct 2013 15:12:32 +0000 (18:12 +0300)]
usb: phy: omap-usb2: Don't use omap_get_control_dev()
omap_get_control_dev() is being deprecated as it doesn't support
multiple instances. As control device is present only from OMAP4
onwards which supports DT only, we use phandles to get the
reference to the control device.
As we don't support non-DT boot, we just bail out on probe
if device node is not present.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Quadros [Thu, 3 Oct 2013 15:12:31 +0000 (18:12 +0300)]
usb: phy: omap: Add new device types and remove omap_control_usb3_phy_power()
Add support for new device types and in the process rid of "ti,type"
device tree property. The correct type of device will be determined
from the compatible string instead.
Introduce a compatible string for each device type. At the moment
we support 4 types OTGHS, USB2, PIPE3 (e.g. USB3) and DRA7USB2.
Update DT binding information to reflect these changes.
Also get rid of omap_control_usb3_phy_power(). Just one function
i.e. omap_control_usb_phy_power() will now take care of all PHY types.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds an implementation for hwahc_op_get_frame_number. The
request is fulfulled by forwarding it to the lower hcd. This was done
because the GET_TIME request on the HWA requires sending an URB to the
HWA and waiting for the results which cannot be done in atomic context.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Pugliese [Tue, 1 Oct 2013 15:14:56 +0000 (10:14 -0500)]
usb: wusbcore: avoid stack overflow in URB enqueue error path
This patch modifies wa_urb_enqueue to return an error and not call the
urb completion routine if it failed to enqueue the urb because the HWA
device is gone. This prevents a stack overflow due to infinite
submit/complete recursion when unplugging the HWA while connected to a
HID device.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Huang Rui [Thu, 3 Oct 2013 15:37:13 +0000 (23:37 +0800)]
usb: ohci: use amd_chipset_type to filter for SB800 prefetch
Commit "usb: pci-quirks: refactor AMD quirk to abstract AMD chipset types"
introduced a new AMD chipset type to filter AMD platforms with different
chipsets.
According to a recent thread [1], this patch updates SB800 prefetch routine
in AMD PLL quirk. And make it use the new chipset type to represent SB800
generation.
Huang Rui [Thu, 3 Oct 2013 15:37:12 +0000 (23:37 +0800)]
usb: ehci: use amd_chipset_type to filter for usb subsystem hang bug
Commit "usb: pci-quirks: refactor AMD quirk to abstract AMD chipset types"
introduced a new AMD chipset type to filter AMD platforms with different
chipsets.
According to a recent thread [1], this patch updates USB subsystem hang
symptom quirk which is observed on AMD all SB600 and SB700 revision
0x3a/0x3b. And make it use the new chipset type to represent.
Ian Abbott [Wed, 2 Oct 2013 13:57:51 +0000 (14:57 +0100)]
staging: comedi: ni_65xx: (bug fix) confine insn_bits to one subdevice
The `insn_bits` handler `ni_65xx_dio_insn_bits()` has a `for` loop that
currently writes (optionally) and reads back up to 5 "ports" consisting
of 8 channels each. It reads up to 32 1-bit channels but can only read
and write a whole port at once - it needs to handle up to 5 ports as the
first channel it reads might not be aligned on a port boundary. It
breaks out of the loop early if the next port it handles is beyond the
final port on the card. It also breaks out early on the 5th port in the
loop if the first channel was aligned. Unfortunately, it doesn't check
that the current port it is dealing with belongs to the comedi subdevice
the `insn_bits` handler is acting on. That's a bug.
Redo the `for` loop to terminate after the final port belonging to the
subdevice, changing the loop variable in the process to simplify things
a bit. The `for` loop could now try and handle more than 5 ports if the
subdevice has more than 40 channels, but the test `if (bitshift >= 32)`
ensures it will break out early after 4 or 5 ports (depending on whether
the first channel is aligned on a port boundary). (`bitshift` will be
between -7 and 7 inclusive on the first iteration, increasing by 8 for
each subsequent operation.)
iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
This patch bumps the default number of tags allocated per session by
iscsi-target via transport_alloc_session_tags() -> percpu_ida_init()
by another (tag_num / 2).
This is done to take into account the tags waiting to be acknowledged
and released in iscsit_ack_from_expstatsn(), but who's number are not
directly limited by the CmdSN Window queue_depth being enforced by
the target.
Using a larger value here is also useful to prevent percpu_ida_alloc()
from having to steal tags from other CPUs when no tags are available
on the local CPU, while waiting for unacknowledged tags to be released.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iscsi-target: Perform release of acknowledged tags from RX context
This patch converts iscsit_ack_from_expstatsn() to populate a local
ack_list of commands, and call iscsit_free_cmd() directly from RX
thread context, instead of using iscsit_add_cmd_to_immediate_queue()
to queue the acknowledged commands to be released from TX thread
context.
It is helpful to release the acknowledge commands as quickly as
possible, along with the associated percpu_ida tags, in order to
prevent percpu_ida_alloc() from having to steal tags from other
CPUs while waiting for iscsit_free_cmd() to happen from TX thread
context.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iscsi-target: Only perform wait_for_tasks when performing shutdown
This patch changes transport_generic_free_cmd() to only wait_for_tasks
when shutdown=true is passed to iscsit_free_cmd().
With the advent of >= v3.10 iscsi-target code using se_cmd->cmd_kref,
the extra wait_for_tasks with shutdown=false is unnecessary, and may
end up causing an extra context switch when releasing WRITEs.
Cc: stable@vger.kernel.org # 3.10+ Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
projects / karo-tx-linux.git / log