target/configfs: allocate only 6 slots for dev_cg->default_groups
Only slots 0-5 are used so 6 slots should be enough. I don't see anyone
writting anything else than NULL into ->default_groups[5] so a "late"
initialisation should not happen here.
(nab: Fix up minor apply breakage in for-next)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target/configfs: allocate pointers instead of full struct for default_groups
default_groups is defined as struct config_group **default_groups so
we don't need to allocate a whole struct but only enough space for a
pointer that points there.
(nab: Fix up minor apply breakage in for-next)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Wei Yongjun [Fri, 23 Nov 2012 04:07:39 +0000 (12:07 +0800)]
iscsit: use GFP_ATOMIC under spin lock
The function iscsit_build_conn_drop_async_message() is called
from iscsit_close_connection() with spin lock 'sess->conn_lock'
held, so we should use GFP_ATOMIC instead of GFP_KERNEL.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Cc: stable@vger.kernel.org Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Steve Hodgson [Fri, 16 Nov 2012 16:06:17 +0000 (08:06 -0800)]
qla2xxx: Look up LUN for abort requests
Search through the list of pending commands on the session list to find
the command the initiator is actually aborting, so that we can pass the
correct LUN to the core TMR handling code.
(nab: Allow abort requests to work to LUN=0 with mainline target code)
Signed-off-by: Steve Hodgson <steve@purestorage.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Cc: stable@vger.kernel.org Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
target/iblock: Add WRITE_SAME w/ UNMAP=0 emulation support
This patch adds support for emulation of WRITE_SAME w/ UNMAP=0 within
iblock_execute_write_same() backend code.
The emulation uses a bio_add_page() call for each sector, and by default
enforces a limit of max_write_same_len=0xFFFF (65536) sectors following
what scsi_debug reports per default for MAXIMUM WRITE SAME LENGTH.
It also sets max_write_same_len to the operational default at setup ->
iblock_configure_device() time.
(hch: Move unmap logic into iblock_execute_write_same_unmap + add
check for single sector SGLs in iblock_execute_write_same)
(mkp: Update comment for 0xFFFF magic constant)
(nab: drop left-over max_write_same_len check in iblock_execute_write_same)
Cc: Christoph Hellwig <hch@lst.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new max_write_same_len device attribute for use with
WRITE_SAME w/ UNMAP=0 backend emulation. This can be useful for
lowering the default backend value (IBLOCK uses 0xFFFF).
Also, update block limits VPD emulation code in spc_emulate_evpd_b0() to
report MAXIMUM WRITE SAME LENGTH, and enforce max_write_same_len during
sbc_parse() -> sbc_setup_write_same() CDB sanity checking for all emulated
WRITE_SAME w/ UNMAP=0 cases.
(Robert: Move max_write_same_len check in sbc_setup_write_same() to
check both WRITE_SAME w/ UNMAP=1 and w/ UNMAP=0 cases)
Cc: Christoph Hellwig <hch@lst.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Robert Elliott <Elliott@hp.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target/sbc: Seperate WRITE_SAME based on UNMAP flag in sbc_ops
This patch adds a new sbc_ops->execute_write_same_unmap() caller for use
with WRITE_SAME w/ UNMAP=1, and performs the ->execute_cmd() setup based
this bit within sbc_setup_write_same() code.
Also, makes the changes in sbc_parse_cdb() to handle a sense_reason_t
return from sbc_setup_write_same() on error.
Reported-by: Christoph Hellwig <hch@lst.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Change sbc_emulate_noop to return sense_reason_t
As reported by Fengguang Wu + 0 day build team, the sense_reason_t conversion
in for-next did not catch the recent sbc_emulate_noop() addition in mainline,
producing the following build warning in auto-next:
drivers/target/target_core_sbc.c: In function ‘sbc_parse_cdb’:
drivers/target/target_core_sbc.c:555: warning: assignment from incompatible pointer type
Go ahead and remove duplicate sbc_emulate_verify(), and change VERIFY to
use sbc_emulate_noop() as well.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Kees Cook [Mon, 5 Nov 2012 23:04:34 +0000 (15:04 -0800)]
sbp-target: remove depends on CONFIG_EXPERIMENTAL
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Chris Boot <bootc@bootc.net> CC: "Nicholas A. Bellinger" <nab@linux-iscsi.org> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Roland Dreier [Tue, 6 Nov 2012 02:02:42 +0000 (18:02 -0800)]
iscsi-target: Always send a response before terminating iSCSI connection
There are some cases, for example when the initiator sends an
out-of-bounds ErrorRecoveryLevel value, where the iSCSI target
terminates the connection without sending back any error. Audit the
login path and add appropriate iscsit_tx_login_rsp() calls to make
sure this doesn't happen.
Signed-off-by: Roland Dreier <roland@purestorage.com> Cc: <stable@vger.kernel.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Steve Hodgson [Tue, 6 Nov 2012 02:02:41 +0000 (18:02 -0800)]
iscsi-target: Fix bug in handling of ExpStatSN ACK during u32 wrap-around
This patch fixes a bug in the hanlding of initiator provided ExpStatSN and
individual iscsi_cmd->stat_sn comparision during iscsi_conn->stat_sn
wrap-around within iscsit_ack_from_expstatsn() code.
This bug would manifest itself as iscsi_cmd descriptors not being Acked
by a lower ExpStatSn, causing them to be leaked until an iSCSI connection
or session reinstatement event occurs to release all commands.
Also fix up two other uses of incorrect CmdSN SNA comparison to use wrapper
usage from include/scsi/iscsi_proto.h.
Signed-off-by: Steve Hodgson <steve@purestorage.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Cc: <stable@vger.kernel.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Roland Dreier [Tue, 6 Nov 2012 02:02:40 +0000 (18:02 -0800)]
iscsi-target: Fix potential deadlock on lock taken in timer
We need to disable BHs when taking sess_idr_lock because the
iscsit_handle_time2retain_timeout() timer function takes
se_tpg->session_lock, and iscsit_close_session() nests sess_idr_lock
inside se_tpg->session_lock. So if the timer can run inside
sess_idr_lock, we have a potential AB-BA deadlock.
Fix this by disabling BHs when taking sess_idr_lock. This was found
because of a lockdep warning, but it looks like a real (if highly
theoretical) deadlock. In any case avoiding lockdep spew so that we can
find other issues is a worthy cause.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Fix exception path pr_reg put regression for PR RELEASE
Fix a regression bug in core_scsi3_emulate_pro_release() where
should still be getting released via core_scsi3_put_pr_reg() during
No persistent reservation, with returing GOOD status.
Use goto statement here to follow converted code from hch.
Cc: Christoph Hellwig <hch@lst.de> Cc: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Fix possible TFO->write_pending() sense_reason_t silent WRITE corruption
This patch fixes a possible case in transport_generic_new_cmd() where a
failure from TFO->write_pending() from a fabric module return something
other than -EAGAIN or -ENOMEM would cause a failed WRITE to silently
succeed.
Go ahead and return TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE for this
special case instead of only just making noise with WARN_ON().
(v2: Fix incorrect exception return for all cases)
Cc: Christoph Hellwig <hch@lst.de> Cc: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Fix incorrect inversion of TPGS_EXPLICT_ALUA check
Fix a bug introduced with patch "target: pass sense_reason as a return value"
in for-3.8 code where only target port groups with TPGS_EXPLICT_ALUA set
need to be allowed to perform explictly ALUA.
Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pass the sense reason as an explicit return value from the I/O submission
path instead of storing it in struct se_cmd and using negative return
values. This cleans up a lot of the code pathes, and with the sparse
annotations for the new sense_reason_t type allows for much better
error checking.
(nab: Convert spc_emulate_modesense + spc_emulate_modeselect to use
sense_reason_t with Roland's MODE SELECT changes)
Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
target: Fix incorrect starting offset after MODE_SENSE refactoring
This patch fixes a new off-by-one bug in the hardcoded starting offset of
spc_emulate_modesense() code that causes BLOCK DESCRIPTOR to be incorrectly
written within the MEDIUM TYPE buffer area of the mode parameter header.
According to spc4r30, Section 7.5.4, BLOCK DESCRIPTOR for MODE_SENSE_10
starts at byte 3, and BLOCK_DESCRIPTOR for MODE_SENSE (6) starts at byte 2.
(roland: add MODE DATA LENGTH + MEDIUM TYPE offset comment)
Cc: Roland Dreier <roland@purestorage.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Roland Dreier [Wed, 31 Oct 2012 16:16:50 +0000 (09:16 -0700)]
target: Add emulation for MODE SELECT
This is another thing that compliance tests try, and it's easy to
implement on top of the MODE SENSE refactoring; since we don't claim
to support any changeable values, all we need to do is check that
the page contents sent by the initiator match what we would return.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The Windows SCSI compliance test asks for this mode page, and it's
easy to implement: we can just return all 0s to show we don't support
any of these features.
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Roland Dreier [Wed, 31 Oct 2012 16:16:48 +0000 (09:16 -0700)]
target: Refactor MODE SENSE emulation
Convert spc_emulate_modesense() to use a table of mode pages, rather
than a switch statement. This makes it possible to add more pages
sanely -- in particular we no longer need to make sure we keep the
0x3f (return all mode pages) case in sync.
While we're touching this code, make our MODE SENSE emulation a bit
better in a couple of ways:
- When the initiator passes PC == 1 asking for changeable values,
return all 0s to show we don't support setting anything.
- Return a block descriptor for disk devices.
(nab: fix up device attribute references to use dev->dev_attrib
in for-next code)
Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Roland Dreier [Wed, 31 Oct 2012 16:16:47 +0000 (09:16 -0700)]
iscsi-target: Use list_first_entry() where appropriate
Instead of using the obfuscated pattern of
list_for_each_entry(var, list, ...)
break;
to set var to the first entry of a list, use the straightforward
var = list_first_entry(list, ...);
Reported-by: Joern Engel <joern@logfs.org> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that the reservations and ALUA code have been cleaned up there is no need
for the get_device_rev method, as we only need the standards revision in the
inquiry data, where we can hardcode it.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We always support ALUA for virtual backends, and never for physical ones. Simplify
the code to just deal with these two cases and remove the superflous abstractions.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We do not support host-level reservations for the pscsi backend, and all
virtual backends are newere than SCSI-2, so just make the combined
SPC-3 + SCSI-2 support the only supported variant and kill the switches
for the different implementations, given that this code handles the no-op
version just fine.
Simplify the code a lot by killing the superflous struct se_subsystem_dev.
Instead se_device is allocated early on by the backend driver, which allocates
it as part of its own per-device structure, borrowing the scheme that is for
example used for inode allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds [Sat, 3 Nov 2012 22:27:21 +0000 (15:27 -0700)]
Merge tag 'nfs-for-3.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix a bunch of deadlock situations:
* State recovery can deadlock if we fail to release sequence ids
before scheduling the recovery thread.
* Calling deactivate_super() from an RPC workqueue thread can
deadlock because of the call to rpc_shutdown_client.
- Display the device name correctly in /proc/*/mounts
- Fix a number of incorrect error return values:
* When NFSv3 mounts fail due to a timeout.
* On NFSv4.1 backchannel setup failure
* On NFSv4 open access checks
- pnfs_find_alloc_layout() must check the layout pointer for NULL
- Fix a regression in the legacy DNS resolved
* tag 'nfs-for-3.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS4: nfs4_opendata_access should return errno
NFSv4: Initialise the NFSv4.1 slot table highest_used_slotid correctly
SUNRPC: return proper errno from backchannel_rqst
NFS: add nfs_sb_deactive_async to avoid deadlock
nfs: Show original device name verbatim in /proc/*/mount{s,info}
nfsv3: Make v3 mounts fail with ETIMEDOUTs instead EIO on mountd timeouts
nfs: Check whether a layout pointer is NULL before free it
NFS: fix bug in legacy DNS resolver.
NFSv4: nfs4_locku_done must release the sequence id
NFSv4.1: We must release the sequence id when we fail to get a session slot
NFS: Wait for session recovery to finish before returning
Linus Torvalds [Sat, 3 Nov 2012 22:25:14 +0000 (15:25 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management & ACPI update from Zhang Rui,
Ho humm. Normally these things go through Len. But it's just three
small fixes, I guess I can pull directly too.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
exynos4_tmu_driver_ids should be exynos_tmu_driver_ids.
ACPI video: Ignore errors after _DOD evaluation.
thermal: solve compilation errors in rcar_thermal
Linus Torvalds [Sat, 3 Nov 2012 22:14:54 +0000 (15:14 -0700)]
Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pull i2c embedded fixes from Wolfram Sang:
"Two patches are usual stuff.
The bigger patch is needed to correct a wrong decision made in this
merge window. We hoped to get the PIOQUEUE mode in the mxs driver
working with DMA, but it turned out to be too broken (leading to data
loss), so we now think it is best to remove it entirely and work only
with DMA now. The patch should be in 3.7. IMO, so users never get
the chance to use both modes in parallel."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: tegra: set irq name as device name
i2c-nomadik: Fixup clock handling
i2c: mxs: remove broken PIOQUEUE support
it's slightly bigger than I'd probably like, but nothing looked
dangerous enough to hold off on."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/udl: fix stride issues scanning out stride != width*bpp
drm/radeon: add load detection support for ext DAC on R200 (v2)
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
DRM/Radeon: Clean up code in TV DAC load detection.
drm/radeon: fix ATPX function documentation
drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
DRM/Radeon: Fix Load Detection on legacy primary DAC.
drm: exynos: removed warning due to missing typecast for mixer driver data
drm/exynos: add support for ARCH_MULTIPLATFORM
MAINTAINERS: Add git repository for Exynos DRM
drm/exynos: fix display on issue
drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
drm/i915: be less verbose about inability to provide vendor backlight
drm/i915: clear the entire sdvo infoframe buffer
drm/i915: VGA needs to be on pipe A on i830M
drm/i915: fix overlay on i830M
Pull networking fixes from David Miller:
"First post-Sandy pull request"
1) Fix antenna gain handling and initialization of chan->max_reg_power
in wireless, from Felix Fietkau.
2) Fix nexthop handling in H.232 conntrack helper, from Julian
Anastasov.
3) Only process 80211 mesh config header in certain kinds of frames,
from Javier Cardona.
4) 80211 management frame header length needs to be validated, from
Johannes Berg.
5) Don't access free'd SKBs in ath9k driver, from Felix Fietkay.
6) Test for permanent state correctly in VXLAN driver, from Stephen
Hemminger.
7) BNX2X bug fixes from Yaniv Rosner and Dmitry Kravkov.
8) Fix off by one errors in bonding, from Nikolay ALeksandrov.
9) Fix divide by zero in TCP-Illinois congestion control. From Jesper
Dangaard Brouer.
10) TCP metrics code says "Yo dawg, I heard you like sizeof, so I did a
sizeof of a sizeof, so you can size your size" Fix from Julian
Anastasov.
11) Several drivers do mdiobus_free without first doing an
mdiobus_unregister leading to stray pointer references. Fix from
Peter Senna Tschudin.
12) Fix OOPS in l2tp_eth_create() error path, it's another danling
pointer kinda situation. Fix from Tom Parkin.
13) Hardware driven by the vmxnet driver can't handle larger than 16K
fragments, so split them up when necessary. From Eric Dumazet.
14) Handle zero length data length in tcp_send_rcvq() properly. Fix
from Pavel Emelyanov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tcp-repair: Handle zero-length data put in rcv queue
vmxnet3: must split too big fragments
l2tp: fix oops in l2tp_eth_create() error path
cxgb4: Fix unable to get UP event from the LLD
drivers/net/phy/mdio-bitbang.c: Call mdiobus_unregister before mdiobus_free
drivers/net/ethernet/nxp/lpc_eth.c: Call mdiobus_unregister before mdiobus_free
bnx2x: fix HW initialization using fw 7.8.x
tcp: Fix double sizeof in new tcp_metrics code
net: fix divide by zero in tcp algorithm illinois
net: sctp: Fix typo in net/sctp
bonding: fix second off-by-one error
bonding: fix off-by-one error
bnx2x: Disable FCoE for 57840 since not yet supported by FW
bnx2x: Fix no link on 577xx 10G-baseT
bnx2x: Fix unrecognized SFP+ module after driver is loaded
bnx2x: Fix potential incorrect link speed provision
bnx2x: Restore global registers back to default.
bnx2x: Fix link down in 57712 following LFA
bnx2x: Fix 57810 1G-KR link against certain switches.
ixgbe: PTP get_ts_info missing software support
...
Pavel Emelyanov [Mon, 29 Oct 2012 05:05:33 +0000 (05:05 +0000)]
tcp-repair: Handle zero-length data put in rcv queue
When sending data into a tcp socket in repair state we should check
for the amount of data being 0 explicitly. Otherwise we'll have an skb
with seq == end_seq in rcv queue, but tcp doesn't expect this to happen
(in particular a warn_on in tcp_recvmsg shoots).
Signed-off-by: Pavel Emelyanov <xemul@parallels.com> Reported-by: Giorgos Mavrikas <gmavrikas@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Parkin [Mon, 29 Oct 2012 23:41:48 +0000 (23:41 +0000)]
l2tp: fix oops in l2tp_eth_create() error path
When creating an L2TPv3 Ethernet session, if register_netdev() should fail for
any reason (for example, automatic naming for "l2tpeth%d" interfaces hits the
32k-interface limit), the netdev is freed in the error path. However, the
l2tp_eth_sess structure's dev pointer is left uncleared, and this results in
l2tp_eth_delete() then attempting to unregister the same netdev later in the
session teardown. This results in an oops.
To avoid this, clear the session dev pointer in the error path.
Signed-off-by: Tom Parkin <tparkin@katalix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Murzov [Sat, 13 Oct 2012 00:41:25 +0000 (04:41 +0400)]
ACPI video: Ignore errors after _DOD evaluation.
There are systems where video module known to work fine regardless
of broken _DOD and ignoring returned value here doesn't cause
any issues later. This should fix brightness controls on some laptops.
Devendra Naga [Wed, 31 Oct 2012 08:46:10 +0000 (17:46 +0900)]
thermal: solve compilation errors in rcar_thermal
following were the errors reported
drivers/thermal/rcar_thermal.c: In function ‘rcar_thermal_probe’:
drivers/thermal/rcar_thermal.c:214:10: warning: passing argument 3 of ‘thermal_zone_device_register’ makes integer from pointer without a cast [enabled by default]
include/linux/thermal.h:166:29: note: expected ‘int’ but argument is of type ‘struct rcar_thermal_priv *’
drivers/thermal/rcar_thermal.c:214:10: error: too few arguments to function ‘thermal_zone_device_register’
include/linux/thermal.h:166:29: note: declared here
make[1]: *** [drivers/thermal/rcar_thermal.o] Error 1
make: *** [drivers/thermal/rcar_thermal.o] Error 2
with gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5)
Vipul Pandya [Mon, 29 Oct 2012 02:02:36 +0000 (02:02 +0000)]
cxgb4: Fix unable to get UP event from the LLD
If T4 configuration file gets loaded from the /lib/firmware/cxgb4/ directory
then offload capabilities of the cards were getting disabled during
initialization. Hence ULDs do not get an UP event from the LLD.
Signed-off-by: Jay Hernandez <jay@chelsio.com> Signed-off-by: Vipul Pandya <vipul@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com> Tested-by: Roland Stigge <stigge@antcom.de> Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Kravkov [Sun, 28 Oct 2012 21:59:04 +0000 (21:59 +0000)]
bnx2x: fix HW initialization using fw 7.8.x
Since commit 96bed4b9 (use FW 7.8.2) BRB HW block needs to be
initialized using fw values for all devices.
Otherwise ETS on 57712/578xx will not work.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: Ariel Elior <ariele@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more scsi target fixes from Nicholas Bellinger:
"This series is a second round of target fixes for v3.7-rc4 that have
come into target-devel over the last days, and are important enough to
be applied ASAP.
All are being CC'ed to stable. The most important two are:
- target: Re-add explict zeroing of INQUIRY bounce buffer memory to
fix a regression for handling zero-length payloads, a bug that went
during v3.7-rc1, and hit >= v3.6.3 stable. (nab + paolo)
- iscsi-target: Fix a long-standing missed R2T wakeup race in TX
thread processing when using a single queue slot. (Roland)
Thanks to Roland & PureStorage team for helping to track down this
long standing race with iscsi-target single queue slot operation.
Also, the tcm_fc(FCoE) regression bug that was observed recently with
-rc2 code has also been resolved with the cancel_delayed_work() return
bugfix (commit c0158ca64da5: "workqueue: cancel_delayed_work() should
return %false if work item is idle") now in -rc3. Thanks again to Yi
Zou, MDR, Robert Love @ Intel for helping to track this down."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix incorrect usage of nested IRQ spinlocks in ABORT_TASK path
iscsi-target: Fix missed wakeup race in TX thread
target: Avoid integer overflow in se_dev_align_max_sectors()
target: Don't return success from module_init() if setup fails
target: Re-add explict zeroing of INQUIRY bounce buffer memory
Linus Torvalds [Fri, 2 Nov 2012 20:27:52 +0000 (13:27 -0700)]
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"An e-mail address update, and fix a compile error on SPARC"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: Only include of_match_table with CONFIG_OF_GPIO
hwmon, fam15h_power: Change email address, MAINTAINERS entry
Linus Torvalds [Fri, 2 Nov 2012 20:27:01 +0000 (13:27 -0700)]
Merge tag 'frv-fixes-20121102' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frv
Pull FRV fixes from David Howells:
"A collection of small fixes for the FRV architecture."
* tag 'frv-fixes-20121102' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-frv:
frv: fix the broken preempt
frv: switch to saner kernel_execve() semantics
FRV: Fix the new-style kernel_thread() stuff
FRV: Fix the preemption handling
FRV: gcc-4.1.2 also inlines weak functions
FRV: Don't objcopy the GNU build_id note
FRV: Add missing linux/export.h #inclusions
Linus Torvalds [Fri, 2 Nov 2012 20:26:11 +0000 (13:26 -0700)]
Merge tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Use appropriate macros instead of hand-rolling our own (ARM).
- Fixes if FB/KBD closed unexpectedly.
- Fix memory leak in /dev/gntdev ioctl calls.
- Fix overflow check in xenbus_file_write.
- Document cleanup.
- Performance optimization when migrating guests.
* tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/mmu: Use Xen specific TLB flush instead of the generic one.
xen/arm: use the __HVC macro
xen/xenbus: fix overflow check in xenbus_file_write()
xen-kbdfront: handle backend CLOSED without CLOSING
xen-fbfront: handle backend CLOSED without CLOSING
xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF
x86: remove obsolete comment from asm/xen/hypervisor.h
Sasha Levin [Tue, 30 Oct 2012 18:45:57 +0000 (14:45 -0400)]
hashtable: introduce a small and naive hashtable
This hashtable implementation is using hlist buckets to provide a simple
hashtable to prevent it from getting reimplemented all over the kernel.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
[ Merging this now, so that subsystems can start applying Sasha's
patches that use this - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Fri, 2 Nov 2012 16:05:44 +0000 (12:05 -0400)]
frv: fix the broken preempt
Just get %icc2 into the state we would have after local_irq_disable()
and physical IRQ having happened since then. Then we can simply
use preempt_schedule_irq() and be done with the whole mess.
Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David Howells [Fri, 2 Nov 2012 13:20:43 +0000 (13:20 +0000)]
FRV: Fix the new-style kernel_thread() stuff
The kernel_thread() changes for FRV don't work, and FRV fails to boot,
starting with:
commit 02ce496f152df87be081a64796498942c433a2fd
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Tue Sep 18 22:18:51 2012 -0400
Subject: frv: split ret_from_fork, simplify kernel_thread() a lot
The problem is that the userspace registers are completely cleared when a
kernel thread is created and all subsequent user threads are then copied from
that. Unfortunately, however, the TBR and PSR registers are restored from the
pt_regs and the values they should be set to are clobbered by the memset.
Instead, copy across the old user registers as normal, and then merely alter
GR8 and GR9 in it if we're going to execute a kernel thread.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 2 Nov 2012 13:20:42 +0000 (13:20 +0000)]
FRV: Fix the preemption handling
Fix the preemption handling in FRV code where the PREEMPT_ACTIVE value is
incorrectly loaded into the threadinfo flags rather than the threadinfo
preemption count.
Unfortunately, the code cannot be simply converted to use
preempt_schedule_irq() as is because FRV uses virtual interrupt disablement to
cut down on the cost of actually disabling interrupts and thus
local_irq_enable() doesn't actually enable interrupts.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Al Viro <viro@ZenIV.linux.org.uk>
Wolfram Sang [Fri, 12 Oct 2012 10:55:16 +0000 (11:55 +0100)]
i2c: mxs: remove broken PIOQUEUE support
This I2C master can do DMA and PIOQUEUE (PIO with FIFO). Originally,
only PIOQUEUE was supported and it had issues, then DMA support was added
this cycle. The original intention was to keep PIOQUEUE since it has
less overhead what is nice for small transfers. However, runtime
switching between PIOQEUE and DMA depending on the transfer size never
worked despite a lot of trying. Since PIOQUEUE mode itself was flaky
(polling at places where interrupts failed to work) and the
implementation also imposed a size limit for transfers, it is best to
remove the support, so users don't fall over its limitations. It also
makes the driver a lot cleaner and more robust. If somebody really wants
less overhead, plain PIO mode could still be implemented with the
addidtional advantage that this mode is also available on MX23, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Reviewed-by: Marek Vasut <marex@denx.de>
Linus Torvalds [Fri, 2 Nov 2012 00:48:19 +0000 (17:48 -0700)]
Merge tag 'xtensa-next-20121101' of git://github.com/czankel/xtensa-linux
Pull Xtensa fixes from Chris Zankel:
"Some important bug fixes.
With the change to uapi, there was a bug introduced that results in an
empty syscall table (mult-inclusion bug). Switching to the generic
thread/execve allowed us to fix a bug we had in vfork()."
* tag 'xtensa-next-20121101' of git://github.com/czankel/xtensa-linux:
xtensa: switch to generic sys_execve()
xtensa: switch to generic kernel_execve()
xtensa: switch to generic kernel_thread()
xtensa: reset windowbase/windowstart when cloning the VM
xtensa: use physical addresses for bus addresses
xtensa: allow multi-inclusion for uapi/unistd.h
Dave Airlie [Thu, 1 Nov 2012 03:47:09 +0000 (13:47 +1000)]
drm/udl: fix stride issues scanning out stride != width*bpp
When buffer sharing with the i915 and using a 1680x1050 monitor,
the i915 gives is a 6912 buffer for the 6720 width, the code doesn't
render this properly as it uses one value to set the base address for
reading from the vmap and for where to start on the device.
This fixes it by calculating the values correctly for the device and
for the pixmap. No idea how I haven't seen this before now.
Cc: stable@vger.kernel.org Signed-off-by: Dave Airlie <airlied@redhat.com>
Jamie Lentin [Thu, 1 Nov 2012 23:55:43 +0000 (23:55 +0000)]
hwmon: Only include of_match_table with CONFIG_OF_GPIO
The following fixes build errors on sparc. Without any DT support,
of_match_ptr is NULL and the below is a no-op. However, if just
CONFIG_OF is defined then so is of_match_ptr.
All useful parts of the gpio-fan DT support rely on CONFIG_OF_GPIO
anyway, so of_match_table should too.
Dave Airlie [Fri, 2 Nov 2012 00:30:37 +0000 (10:30 +1000)]
Merge branch 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Inki writes:
"As I posted before, we have added a new git repository for Exynos drm
to MAINTAINERS file so change it to new one like below,
from git://git.infradead.org/users/kmpark/linux-samsung
to git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos
And this pull request includes the following:
- fix display on issue when user requested dpms mode changing.
- add git repository for Exynos drm to MAINTAINERS file.
- add support for ARCH_MULTIPLATFORM.
- and code clean."
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm: exynos: removed warning due to missing typecast for mixer driver data
drm/exynos: add support for ARCH_MULTIPLATFORM
MAINTAINERS: Add git repository for Exynos DRM
drm/exynos: fix display on issue
Dave Airlie [Fri, 2 Nov 2012 00:29:22 +0000 (10:29 +1000)]
Merge branch 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex writes:
"This request is mostly load detection fixes from Egbert and me."
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add load detection support for ext DAC on R200 (v2)
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
DRM/Radeon: Clean up code in TV DAC load detection.
drm/radeon: fix ATPX function documentation
drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
DRM/Radeon: Fix Load Detection on legacy primary DAC.
Dave Airlie [Fri, 2 Nov 2012 00:26:03 +0000 (10:26 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel Vetter writes"
Nothing big at all for -fixes, just small stuff:
- Two patches to fix bugs on i830M
- ums regression fixer due to kicking firmeware fbs (Chris)
- tune down a too loud warning (Jani)
- be more careful with sdvo infoframes, which fixes a long-standing
sdvo-hdmi regression"
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
drm/i915: be less verbose about inability to provide vendor backlight
drm/i915: clear the entire sdvo infoframe buffer
drm/i915: VGA needs to be on pipe A on i830M
drm/i915: fix overlay on i830M
Reading TCP stats when using TCP Illinois congestion control algorithm
can cause a divide by zero kernel oops.
The division by zero occur in tcp_illinois_info() at:
do_div(t, ca->cnt_rtt);
where ca->cnt_rtt can become zero (when rtt_reset is called)
Steps to Reproduce:
1. Register tcp_illinois:
# sysctl -w net.ipv4.tcp_congestion_control=illinois
2. Monitor internal TCP information via command "ss -i"
# watch -d ss -i
3. Establish new TCP conn to machine
Either it fails at the initial conn, or else it needs to wait
for a loss or a reset.
This is only related to reading stats. The function avg_delay() also
performs the same divide, but is guarded with a (ca->cnt_rtt > 0) at its
calling point in update_params(). Thus, simply fix tcp_illinois_info().
Function tcp_illinois_info() / get_info() is called without
socket lock. Thus, eliminate any race condition on ca->cnt_rtt
by using a local stack variable. Simply reuse info.tcpv_rttcnt,
as its already set to ca->cnt_rtt.
Function avg_delay() is not affected by this race condition, as
its called with the socket lock.
Cc: Petr Matousek <pmatouse@redhat.com> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Masanari Iida [Wed, 31 Oct 2012 05:48:19 +0000 (05:48 +0000)]
net: sctp: Fix typo in net/sctp
Correct spelling typo in net/sctp/socket.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.
How to reproduce:
with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/active_slave;
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Note: Sorry for the second patch but I missed this one while checking
the file. You can squash them into one patch. Signed-off-by: David S. Miller <davem@davemloft.net>
Fix off-by-one error because IFNAMSIZ == 16 and when this
code gets executed we stick a NULL byte where we should not.
How to reproduce:
with CONFIG_CC_STACKPROTECTOR=y (otherwise it may pass by silently)
modprobe bonding; echo 1 > /sys/class/net/bond0/bonding/mode;
echo "AAAAAAAAAAAAAAAA" > /sys/class/net/bond0/bonding/primary;
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:57 +0000 (05:46 +0000)]
bnx2x: Fix no link on 577xx 10G-baseT
Since the Warpcore supports various link types, need to set only the correct
supported modes for XFI which is the serdes interface for the 10G-baseT PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:56 +0000 (05:46 +0000)]
bnx2x: Fix unrecognized SFP+ module after driver is loaded
When SFP+ module is plugged in after driver is already loaded, it may not be
recognized, so set SFP module recognition time up to 300ms, without resetting
the module power in the middle.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:55 +0000 (05:46 +0000)]
bnx2x: Fix potential incorrect link speed provision
Fix possible incorrect link speed provision following rapid link speed change.
Clear link speed mask after each link change, and not only after link down.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yaniv Rosner [Wed, 31 Oct 2012 05:46:54 +0000 (05:46 +0000)]
bnx2x: Restore global registers back to default.
Several KR registers were not set correctly back to default after
loopback test, so set those global registers over the global WC lane (zero)
rather than the current lane.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Barak Witkowski <barak@broadcom.com> Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Wed, 31 Oct 2012 22:30:54 +0000 (22:30 +0000)]
ixgbe: PTP get_ts_info missing software support
This patch corrects the ethtool get_ts_info functon which did not state that
software timestamping was supported, even though it is.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> CC: Stable <stable@vger.kernel.org> [3.5] Tested-by: Stephen Ko <stephen.s.ko@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Deucher [Wed, 31 Oct 2012 15:51:03 +0000 (11:51 -0400)]
drm/radeon: add load detection support for ext DAC on R200 (v2)
The R200 asics use an external DAC for the secondary DAC.
The current KMS code tries to use code for the integrated
TV DAC for R200 which leads to unpredictable results since
R200 does not have an integrated TV DAC. This patch ports
the external DAC load detection support from the UMS
driver to KMS.
v2: fix typo in loop break logic
Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Egbert Eich <eich@suse.de>
Egbert Eich [Mon, 29 Oct 2012 12:46:48 +0000 (13:46 +0100)]
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
On all dual CRTC GPUs the CRTC_CRT_ON in the RADEON_CRTC_EXT_CNTL register
controls the CRTC of the primary DAC. Therefore it is set in the DAC DMPS
function.
This is different for GPU's with a single CRTC but a primary and a
TV DAC: here it controls the single CRTC no matter where it is routed.
Therefore we set it here. This avoids an elaborate on/off state tracking
since both primary_dac_dpms() and tv_dac_dpms() functions would have
to touch this bit.
On single CRTC GPUs with just one DAC it's irrelevant where this bit
is handled.
agd5f: fix warning
Signed-off-by: Egbert Eich <eich@suse.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
projects / linux-beck.git / log