Matt Carlson [Tue, 13 Nov 2007 05:10:58 +0000 (21:10 -0800)]
[TG3]: Fix nvram selftest failures
Newer devices contain bootcode in the chip's private ROM area. This
bootcode is called selfboot. Selfboot can be patched in the device's
NVRAM and the patches can have several formats. In one particular
format, the checksum calculation needs to be slightly modified. This
patch adjusts the NVRAM test code for that case, and add support for the
missing formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Tue, 13 Nov 2007 05:10:06 +0000 (21:10 -0800)]
[TG3]: 5784 / 5764 DMA engine lockup fix
5784 and 5764 devices lock up when the link speed is 10Mbps, the CPMU
link speed mode is enabled, and the MAC clock is running at 1.5Mhz. The
fix is to run the MAC clock at faster speeds.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Tue, 13 Nov 2007 05:08:59 +0000 (21:08 -0800)]
[TG3]: APE flag fix
This patch corrects a bug where the ENABLE_APE flag was tested against
the wrong flag variable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Tue, 13 Nov 2007 05:08:03 +0000 (21:08 -0800)]
[TG3]: 5784 / 5764 GPHY power down fix
5784 and 5764 devices fail to link / pass traffic after one load /
unload cycle. This happens because of a hardware bug in the new CPMU.
During normal operation, the MAC depends on the PHY clock being
available. When the PHY is powered down, the clock the MAC depends on
is disabled. The fix is to switch the MAC clock to an alternate source
before powering down the PHY, and to restore the MAC clock to the PHY
source upon device resume.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Tue, 13 Nov 2007 05:07:01 +0000 (21:07 -0800)]
[TG3]: Fix 5761 PXEboot crash
When 5761 devices boot the machine using PXEboot, PXE leaves the device
active when it terminates. The tg3 driver has code to detect this
condition and resets the device during initialization. On 5761 devices,
device resets involve sending a driver state update message to the APE
on the 5761. However, during this initialization stage, communications
to the APE registers have not yet been set up. The driver then
dereferences a NULL pointer and crashes the machine. The fix is to move
the APE register access setup earlier in the initialization code to
cover this condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Trond Myklebust [Tue, 13 Nov 2007 02:10:39 +0000 (18:10 -0800)]
[NET]: Add the helper kernel_sock_shutdown()
...and fix a couple of bugs in the NBD, CIFS and OCFS2 socket handlers.
Looking at the sock->op->shutdown() handlers, it looks as if all of them
take a SHUT_RD/SHUT_WR/SHUT_RDWR argument instead of the
RCV_SHUTDOWN/SEND_SHUTDOWN arguments.
Add a helper, and then define the SHUT_* enum to ensure that kernel users
of shutdown() don't get confused.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com> Acked-by: Mark Fasheh <mark.fasheh@oracle.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 13 Nov 2007 02:09:25 +0000 (18:09 -0800)]
[SUNGEM]: Fix suspend regression due to NAPI changes.
Commit bea3348e (the NAPI changes) made sungem unconditionally enable
NAPI when resuming and unconditionally disable when suspending, this,
however, makes napi_disable() hang when suspending when the interface
was taken down before suspend because taking the interface down also
disables NAPI. This patch makes touching the napi struct in
suspend/resume code paths depend on having the interface up, thereby
fixing the hang on suspend.
The patch also moves the napi_disable() in gem_close() under the lock so
that the NAPI state is always modified atomically together with the
"opened" variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Pierre Ynard [Tue, 13 Nov 2007 01:58:35 +0000 (17:58 -0800)]
[IPV6]: Add ifindex field to ND user option messages.
Userland neighbor discovery options are typically heavily involved with
the interface on which thay are received: add a missing ifindex field to
the original struct. Thanks to Rémi Denis-Courmont.
Signed-off-by: Pierre Ynard <linkfanel@yahoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Roland McGrath [Mon, 12 Nov 2007 23:41:55 +0000 (15:41 -0800)]
sigwait eats blocked default-ignore signals
While a signal is blocked, it must be posted even if its action is
SIG_IGN or is SIG_DFL with the default action to ignore. This works
right most of the time, but is broken when a sigwait (rt_sigtimedwait)
is in progress. This changes the early-discard check to respect
real_blocked. ~blocked is the set to check for "should wake up now",
but ~(blocked|real_blocked) is the set for "blocked" semantics as
defined by POSIX.
This fixes bugzilla entry 9347, see
http://bugzilla.kernel.org/show_bug.cgi?id=9347
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
J. Bruce Fields [Mon, 12 Nov 2007 21:05:03 +0000 (16:05 -0500)]
nfsd4: recheck for secure ports in fh_verify
As with commit 7fc90ec93a5eb71f4b08403baf5ba7176b3ec6b1 ("knfsd: nfsd:
call nfsd_setuser() on fh_compose(), fix nfsd4 permissions problem")
this is a case where we need to redo a security check in fh_verify()
even though the filehandle already has an associated dentry--if the
filehandle was created by fh_compose() in an earlier operation of the
nfsv4 compound, then we may not have done these checks yet.
Without this fix it is possible, for example, to traverse from an export
without the secure ports requirement to one with it in a single
compound, and bypass the secure port check on the new export.
While we're here, fix up some minor style problems and change a printk()
to a dprintk(), to make it harder for random unprivileged users to spam
the logs.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Reviewed-By: NeilBrown <neilb@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
J. Bruce Fields [Mon, 12 Nov 2007 21:05:02 +0000 (16:05 -0500)]
knfsd: fix spurious EINVAL errors on first access of new filesystem
The v2/v3 acl code in nfsd is translating any return from fh_verify() to
nfserr_inval. This is particularly unfortunate in the case of an
nfserr_dropit return, which is an internal error meant to indicate to
callers that this request has been deferred and should just be dropped
pending the results of an upcall to mountd.
Thanks to Roland <devzero@web.de> for bug report and data collection.
Cc: Roland <devzero@web.de> Acked-by: Andreas Gruenbacher <agruen@suse.de> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu> Reviewed-By: NeilBrown <neilb@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Dobriyan reports that it causes huge slowdowns under some loads,
in his case a "mkfs.ext2" on a 30G partition. With the placement bias,
the mkfs took over four minutes, with it reverted it's back to about ten
seconds for Alexey.
Linus Torvalds [Mon, 12 Nov 2007 19:13:54 +0000 (11:13 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: SVM: Intercept the 'invd' and 'wbinvd' instructions
KVM: x86 emulator: invd instruction
KVM: SVM: Defer nmi processing until switch to host state is complete
KVM: SVM: Fix SMP with kernel apic
KVM: x86 emulator: fix 'push imm8' emulation
Linus Torvalds [Mon, 12 Nov 2007 19:13:31 +0000 (11:13 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-virtio
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-virtio:
virtio: Force use of power-of-two for descriptor ring sizes
lguest: Fix lguest virtio-blk backend size computation
virtio: Fix used_idx wrap-around
virtio: more fallout from scatterlist changes.
virtio: fix vring_init for 64 bits
Linus Torvalds [Mon, 12 Nov 2007 19:12:06 +0000 (11:12 -0800)]
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (39 commits)
[INET]: Small possible memory leak in FIB rules
[NETNS]: init dev_base_lock only once
[UNIX]: The unix_nr_socks limit can be exceeded
[AF_UNIX]: Convert socks to unix_socks in scan_inflight, not in callbacks
[AF_UNIX]: Make unix_tot_inflight counter non-atomic
[AF_PACKET]: Allow multicast traffic to be caught by ORIGDEV when bonded
ssb: Fix PCMCIA-host lowlevel bus access
mac80211: fix MAC80211_RCSIMPLE Kconfig
mac80211: make "decrypt failed" messages conditional upon MAC80211_DEBUG
mac80211: use IW_AUTH_PRIVACY_INVOKED rather than IW_AUTH_KEY_MGMT
mac80211: remove unused driver ops
mac80211: remove ieee80211_common.h
softmac: MAINTAINERS update
rfkill: Fix sparse warning
rfkill: Use mutex_lock() at register and add sanity check
iwlwifi: select proper rate control algorithm
mac80211: allow driver to ask for a rate control algorithm
mac80211: don't allow registering the same rate control twice
rfkill: Use subsys_initcall
mac80211: make simple rate control algorithm built-in
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: (21 commits)
[CIFS] fix oops on second mount to same server when null auth is used
[CIFS] Fix stale mode after readdir when cifsacl specified
[CIFS] add mode to acl conversion helper function
[CIFS] Fix incorrect mode when ACL had deny access control entries
[CIFS] Add uid to key description so krb can handle user mounts
[CIFS] Fix walking out end of cifs dacl
[CIFS] Add upcall files for cifs to use spnego/kerberos
[CIFS] add OIDs for KRB5 and MSKRB5 to ASN1 parsing routines
[CIFS] Register and unregister cifs_spnego_key_type on module init/exit
[CIFS] implement upcalls for SPNEGO blob via keyctl API
[CIFS] allow cifs_calc_signature2 to deal with a zero length iovec
[CIFS] If no Access Control Entries, set mode perm bits to zero
[CIFS] when mount helper missing fix slash wrong direction in share
[CIFS] Don't request too much permission when reading an ACL
[CIFS] enable get mode from ACL when cifsacl mount option specified
[CIFS] ACL support part 8
[CIFS] acl support part 7
[CIFS] acl support part 6
[CIFS] acl support part 6
[CIFS] remove unused funtion compile warning when experimental off
...
Siddha, Suresh B [Sun, 11 Nov 2007 19:27:59 +0000 (11:27 -0800)]
x86: fix taking DNA during 64bit sigreturn
restore sigcontext is taking a DNA exception while restoring FP context
from the user stack, during the sigreturn. Appended patch fixes it by
doing clts() if the app doesn't touch FP during the signal handler
execution. This will stop generating a DNA, during the fxrstor in the
sigreturn.
This improves 64-bit lat_sig numbers by ~30% on my core2 platform.
Roland McGrath [Mon, 12 Nov 2007 03:13:43 +0000 (19:13 -0800)]
core dump: remain dumpable
The coredump code always calls set_dumpable(0) when it starts (even
if RLIMIT_CORE prevents any core from being dumped). The effect of
this (via task_dumpable) is to make /proc/pid/* files owned by root
instead of the user, so the user can no longer examine his own
process--in a case where there was never any privileged data to
protect. This affects e.g. auxv, environ, fd; in Fedora (execshield)
kernels, also maps. In practice, you can only notice this when a
debugger has requested PTRACE_EVENT_EXIT tracing.
set_dumpable was only used in do_coredump for synchronization and not
intended for any security purpose. (It doesn't secure anything that wasn't
already unsecured when a process dies by SIGTERM instead of SIGQUIT.)
This changes do_coredump to check the core_waiters count as the means of
synchronization, which is sufficient. Now we leave the "dumpable" bits alone.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesper Juhl [Sun, 11 Nov 2007 22:57:49 +0000 (23:57 +0100)]
Fix memory leak in discard case of sctp_sf_abort_violation()
In net/sctp/sm_statefuns.c::sctp_sf_abort_violation() we may leak
the storage allocated for 'abort' by returning from the function
without using or freeing it. This happens in case
"sctp_auth_recv_cid(SCTP_CID_ABORT, asoc)" is true and we jump to
the 'discard' label.
Spotted by the Coverity checker.
The simple fix is to simply move the creation of the "abort chunk"
to after the possible jump to the 'discard' label. This way we don't
even have to allocate the memory at all in the problem case.
Rusty Russell [Mon, 12 Nov 2007 02:39:18 +0000 (13:39 +1100)]
virtio: Force use of power-of-two for descriptor ring sizes
The virtio descriptor rings of size N-1 were nicely set up to be
aligned to an N-byte boundary. But as Anthony Liguori points out, the
free-running indices used by virtio require that the sizes be a power
of 2, otherwise we get problems on wrap (demonstrated with lguest).
So we replace the clever "2^n-1" scheme with a simple "align to page
boundary" scheme: this means that all virtio rings take at least two
pages, but it's safer than guessing cache alignment.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Anthony Liguori [Wed, 7 Nov 2007 21:49:24 +0000 (15:49 -0600)]
virtio: Fix used_idx wrap-around
The more_used() function compares the vq->vring.used->idx with last_used_idx.
Since vq->vring.used->idx is a 16-bit integer, and last_used_idx is an
unsigned int, this results in unpredictable behavior when vq->vring.used->idx
wraps around.
This patch corrects this by changing last_used_idx to the correct type.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Anthony Liguori [Wed, 7 Nov 2007 05:31:52 +0000 (16:31 +1100)]
virtio: fix vring_init for 64 bits
This patch fixes a typo in vring_init(). This happens to work today in lguest
because the sizeof(struct vring_desc) is 16 and struct vring contains 3
pointers and an unsigned int so on 32-bit
sizeof(struct vring_desc) == sizeof(struct vring). However, this is no longer
true on 64-bit where the bug is exposed.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Denis V. Lunev [Sun, 11 Nov 2007 06:12:03 +0000 (22:12 -0800)]
[INET]: Small possible memory leak in FIB rules
This patch fixes a small memory leak. Default fib rules can be deleted by
the user if the rule does not carry FIB_RULE_PERMANENT flag, f.e. by
ip rule flush
Such a rule will not be freed as the ref-counter has 2 on start and becomes
clearly unreachable after removal.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Sun, 11 Nov 2007 06:08:30 +0000 (22:08 -0800)]
[UNIX]: The unix_nr_socks limit can be exceeded
The unix_nr_socks value is limited with the 2 * get_max_files() value,
as seen from the unix_create1(). However, the check and the actual
increment are separated with the GFP_KERNEL allocation, so this limit
can be exceeded under a memory pressure - task may go to sleep freeing
the pages and some other task will be allowed to allocate a new sock
and so on and so forth.
So make the increment before the check (similar thing is done in the
sock_kmalloc) and go to kmalloc after this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Sun, 11 Nov 2007 06:07:13 +0000 (22:07 -0800)]
[AF_UNIX]: Convert socks to unix_socks in scan_inflight, not in callbacks
The scan_inflight() routine scans through the unix sockets and calls
some passed callback. The fact is that all these callbacks work with
the unix_sock objects, not the sock ones, so make this conversion in
the scan_inflight() before calling the callbacks.
This removes one unneeded variable from the inc_inflight_move_tail().
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[AF_PACKET]: Allow multicast traffic to be caught by ORIGDEV when bonded
The socket option for packet sockets to return the original ifindex instead
of the bonded ifindex will not match multicast traffic. Since this socket
option is the most useful for layer 2 traffic and multicast traffic, make
the option multicast-aware.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211: make "decrypt failed" messages conditional upon MAC80211_DEBUG
Make "decrypt failed" and "have no key" debugging messages compile
conditionally upon CONFIG_MAC80211_DEBUG. They have been useful for
finding certain problems in the past, but in many cases they just
clutter a user's logs.
A typical example is an enviornment where multiple SSIDs are using a
single BSSID but with different protection schemes or different keys
for each SSID. In such an environment these messages are just noise.
Let's just leave them for those interested enough to turn-on debugging.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sat, 3 Nov 2007 13:11:10 +0000 (13:11 +0000)]
mac80211: use IW_AUTH_PRIVACY_INVOKED rather than IW_AUTH_KEY_MGMT
In the long bug-hunt for why dynamic WEP networks didn't work it
turned out that mac80211 incorrectly uses IW_AUTH_KEY_MGMT while
it should use IW_AUTH_PRIVACY_INVOKED to determine whether to
associate to protected networks or not.
This patch changes the behaviour to be that way and clarifies the
existing code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 30 Oct 2007 14:58:18 +0000 (15:58 +0100)]
mac80211: remove unused driver ops
The driver operations set_ieee8021x(), set_port_auth() and
set_privacy_invoked() are not used by any drivers, except
set_privacy_invoked() they aren't even used by mac80211.
Remove them at least until we need to support drivers with
mac80211 that require getting this information.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Mon, 5 Nov 2007 13:32:35 +0000 (14:32 +0100)]
softmac: MAINTAINERS update
This patch marks softmac as obsolete in MAINTAINERS and removes Joe and
myself as maintainers, we're no longer using it nor interested in the
code in any way. Also remove the website reference because I took it
offline. Hopefully the code will go away in 2.6.25.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Joseph Jezak <josejx@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sun, 28 Oct 2007 14:16:50 +0000 (15:16 +0100)]
rfkill: Use mutex_lock() at register and add sanity check
Replace mutex_lock_interruptible() by mutex_lock() in rfkill_register(),
as interruptible doesn't make sense there.
Add a sanity check for rfkill->type, as that's used for an unchecked dereference
in an array and might cause hard to debug crashes if the driver sets this
to an invalid value.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sun, 28 Oct 2007 13:53:36 +0000 (14:53 +0100)]
iwlwifi: select proper rate control algorithm
Prior to this patch, iwlwifi would always use the first
registered rate control algorithm which, depending on system
setup, could be anything. After the mac80211 patch to make
the simple algorithm built-in, it would always be simple.
This has always been a bug in iwlwifi.
This fixes it by requesting that mac80211 selects the right
rate control algorithm.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sun, 28 Oct 2007 13:51:05 +0000 (14:51 +0100)]
mac80211: allow driver to ask for a rate control algorithm
This allows a driver to ask for a specific rate control algorithm.
The rate control algorithm asked for must be registered and be
available as a module or built-in.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sun, 28 Oct 2007 13:49:33 +0000 (14:49 +0100)]
mac80211: don't allow registering the same rate control twice
Previously, mac80211 would allow registering the same rate control
algorithm twice. This is a programming error in the registration
and should not happen; additionally the second version could never
be selected. Disallow this and warn about it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sun, 28 Oct 2007 13:17:44 +0000 (14:17 +0100)]
mac80211: make simple rate control algorithm built-in
Too frequently people do not have module autoloading enabled
or fail to install the rate control module correctly, hence
their hardware probing fails due to no rate control algorithm
being available. This makes the 'simple' algorithm built into
the mac80211 module unless EMBEDDED is enabled in which case
it can be disabled (eg. if the wanted driver requires another
rate control algorithm.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sun, 28 Oct 2007 12:07:54 +0000 (13:07 +0100)]
rfkill: Register LED triggers before registering switch
Registering the switch triggers a LED event, so we must register
LED triggers before the switch.
This has a potential to fix a crash, depending on how the device
driver initializes the rfkill data structure.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sat, 27 Oct 2007 13:14:39 +0000 (15:14 +0200)]
ssb: Fix initcall ordering
ssb must init after PCI but before the ssb drivers.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: Christian Casteyde <casteyde.christian@free.fr>
Fixes-bug: #9219 Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MLME request reason code is host-endian and our passing
it to the low level functions is host-endian as well since
they do the swapping. I noticed that the reason code 768 was
sent (0x300) rather than 3 when wpa_supplicant terminates.
This removes the superfluous cpu_to_le16() call.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radu Rendec [Sun, 11 Nov 2007 05:54:50 +0000 (21:54 -0800)]
[PKT_SCHED] CLS_U32: Use ffs() instead of C code on hash mask to get first set bit.
Computing the rank of the first set bit in the hash mask (for using later
in u32_hash_fold()) was done with plain C code. Using ffs() instead makes
the code more readable and improves performance (since ffs() is better
optimized in assembler).
Using the conditional operator on hash mask before applying ntohl() also
saves one ntohl() call if mask is 0.
Signed-off-by: Radu Rendec <radu.rendec@ines.ro> Signed-off-by: Jarek Poplawski <jarkao2@o2.pl> Acked-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Chuck Lever [Sun, 11 Nov 2007 05:53:30 +0000 (21:53 -0800)]
[NET]: Fix skb_truesize_check() assertion
The intent of the assertion in skb_truesize_check() is to check
for skb->truesize being decremented too much by other code,
resulting in a wraparound below zero.
The type of the right side of the comparison causes the compiler to
promote the left side to an unsigned type, despite the presence of an
explicit type cast. This defeats the check for negativity.
Ensure both sides of the comparison are a signed type to prevent the
implicit type conversion.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Sun, 11 Nov 2007 05:47:39 +0000 (21:47 -0800)]
[INET]: Add missed tunnel64_err handler
The tunnel64_protocol uses the tunnel4_protocol's err_handler and
thus calls the tunnel4_protocol's handlers.
This is not very good, as in case of (icmp) error the wrong error
handlers will be called (e.g. ipip ones instead of sit) and this
won't be noticed at all, because the error is not reported.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Sun, 11 Nov 2007 05:39:26 +0000 (21:39 -0800)]
[IPX]: Use existing sock refcnt debugging infrastructure
Just like in the af_packet.c, the ipx_sock_nr variable is used
for debugging purposes.
Switch to using existing infrastructure. Thanks to Arnaldo for
pointing this out.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Sun, 11 Nov 2007 05:38:48 +0000 (21:38 -0800)]
[PACKET]: Use existing sock refcnt debugging infrastructure
The packet_socks_nr variable is used purely for debugging
the number of sockets.
As Arnaldo pointed out, there's already an infrastructure
for this purposes, so switch to using it.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Sun, 11 Nov 2007 05:24:19 +0000 (21:24 -0800)]
[TCP]: Split SACK FRTO flag clearing (fixes FRTO corner case bug)
In case we run out of mem when fragmenting, the clearing of
FLAG_ONLY_ORIG_SACKED might get missed which then feeds FRTO
with false information. Move clearing outside skb processing
loop so that it will get executed even if the skb loop
terminates prematurely due to out-of-mem.
Besides, now the core of the loop truly deals with a single
skb only, which also enables creation a more self-contained
of tcp_sacktag_one later on.
In addition, small reorganization of if branches was made.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Sun, 11 Nov 2007 05:22:18 +0000 (21:22 -0800)]
[TCP]: Fix reord detection due to snd_una covered holes
Fixes subtle bug like the one with fastpath_cnt_hint happening
due to the way the GSO and hints interact. Because hints are not
reset when just a GSOed skb is partially ACKed, there's no
guarantee that the relevant part of the write queue is going to
be processed in sacktag at all (skbs below snd_una) because
fastpath hint can fast forward the entrypoint.
This was also on the way of future reductions in sacktag's skb
processing. Also future cleanups in sacktag can be made after
this (in 2.6.25).
This may make reordering update in tcp_try_undo_partial
redundant but I'm not too sure so I left it there.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Sun, 11 Nov 2007 05:20:59 +0000 (21:20 -0800)]
[TCP]: Consider GSO while counting reord in sacktag
Reordering detection fails to take account that the reordered
skb may have pcount larger than 1. In such case the lowest of
them had the largest reordering, the old formula used the
highest of them which is pcount - 1 packets less reordered.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Jerome Pinot [Sat, 10 Nov 2007 18:01:10 +0000 (03:01 +0900)]
ACPI: add documentation for deprecated /proc/acpi/battery in ACPI_PROCFS
Add documentation in Kconfig help about the move of /proc/acpi/battery
to /sys/class/power_supply when selecting ACPI_PROCFS. This will impact
a lot of users and should be documented.
Linus Torvalds [Sat, 10 Nov 2007 22:26:04 +0000 (14:26 -0800)]
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Don't fail device revalidation for bad _GTF methods
libata: port and host should be stopped before hardware resources are released
libata: skip 0xff polling for PATA controllers
libata: pata_platform: Support polling-mode configuration.
libata: Support PIO polling-only hosts.
libata sata_qstor conversion to new error handling (EH).
libata sata_qstor workaround for spurious interrupts
libata sata_qstor nuke idle state
nv_hardreset: update dangling reference to bugzilla entry
ata_piix: add SATELLITE PRO U200 to broken suspend list
Francois Romieu [Thu, 8 Nov 2007 22:23:21 +0000 (23:23 +0100)]
r8169: prevent bit sign expansion error in mdio_write
Oops.
The current code does not like being given an u16 with the highest
bit set as an argument to mdio_write. Let's enforce a correct range of
values for both the register address and value (resp. 5 and 16 bits).
The callers are currently left as-is.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Ron Mercer [Wed, 7 Nov 2007 21:59:06 +0000 (13:59 -0800)]
qla3xxx: bugfix: Move link state machine into a worker thread
The link state machine requires access to some resources that
are shared with the iSCSI function on the chip. (See iSCSI
driver at drivers/scsi/qla4xxx) If the interface is being
up/downed at a rapid pace this driver may need to sleep
waiting to get access to the common resources. For this we
are moving the state machine to run as a work thread.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Tue, 6 Nov 2007 21:33:29 +0000 (13:33 -0800)]
bonding: don't validate address at device open
The standard validate_addr handler refuses to accept the all zeroes address
as valid. However, it's common historical practice for the bonding
master to be configured up prior to having any slaves, at which time the
master will have a MAC address of all zeroes.
Resolved by setting the dev->validate_addr to NULL. The master still can't
end up with an invalid address, as the set_mac_address function tests
for validity.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jay Vosburgh [Tue, 6 Nov 2007 21:33:28 +0000 (13:33 -0800)]
bonding: fix rtnl locking merge error
Looks like I incorrectly merged one of the rtnl lock changes,
so that one function, bonding_show_active_slave, held rtnl but didn't
release it, and another, bonding_store_active_slave, never held rtnl but
did release it.
Fixed so the first function doesn't mess with rtnl, and the
second correctly acquires and releases rtnl.
Bug reported by Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Stefano Brivio [Wed, 7 Nov 2007 17:33:37 +0000 (18:33 +0100)]
b43legacy: fix shared IRQ race condition
Fix an IRQ race condition in b43legacy. If we call
b43legacy_wireless_core_stop(), it will set the status of the device to
INITIALIZED and the IRQ handler won't care any longer about IRQs, thus the
kernel will disable the IRQ if it's shared (unless we boot it with the
'irqpoll' option). So we must disable IRQs before changing the device
status.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stefano Brivio [Wed, 7 Nov 2007 17:16:11 +0000 (18:16 +0100)]
b43: fix shared IRQ race condition
Fix an IRQ race condition in b43. If we call b43_stop_wireless_core(), it
will set the status of the device to INITIALIZED and the IRQ handler won't
care any longer about IRQs, thus the kernel will disable the IRQ if it's
shared (unless we boot it with the 'irqpoll' option). So we must disable
IRQs before changing the device status.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stefano Brivio [Tue, 6 Nov 2007 21:48:56 +0000 (22:48 +0100)]
b43legacy: add me as maintainer and fix URLs
As b43legacy is going to be orphaned, add me as a maintainer. Fix URLs for
the related website and fix my e-mail address in MAINTAINERS file.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it> Cc: Larry Finger <larry.finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sat, 3 Nov 2007 13:34:32 +0000 (14:34 +0100)]
b43: Rewrite and fix rfkill init
The rfkill subsystem doesn't like code like that
rfkill_allocate();
rfkill_register();
rfkill_unregister();
rfkill_register(); /* <- This will crash */
This sequence happens with
modprobe b43
ifconfig wlanX up
ifconfig wlanX down
ifconfig wlanX up
Fix this by always re-allocating the rfkill stuff before register.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roel Kluin [Mon, 5 Nov 2007 22:55:02 +0000 (23:55 +0100)]
ipw2100: fix postfix decrement errors
If i reaches zero, the loop ends, but the postfix decrement subtracts it to -1.
Testing for 'i == 0', later in the function, will not fulfill its purpose.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sun, 28 Oct 2007 13:39:52 +0000 (14:39 +0100)]
rt2x00: Block adhoc & master mode
rt2x00 is broken when it comes down to adhoc and master mode.
The main problem is the beaconing, which is completely failing.
Untill a solution has been found, both beacon requiring modes
must be disabled to prevent numerous bug reports.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-beck.git / log