Michael Spang [Fri, 14 Sep 2012 17:05:49 +0000 (13:05 -0400)]
Increase XHCI suspend timeout to 16ms
The Intel XHCI specification says that after clearing the run/stop bit
the controller may take up to 16ms to halt. We've seen a device take
14ms, which with the current timeout of 10ms causes the kernel to
abort the suspend. Increasing the timeout to the recommended value
fixes the problem.
This patch should be backported to kernels as old as 2.6.37, that
contain the commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI:
PCI power management implementation".
Signed-off-by: Michael Spang <spang@chromium.org> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@vger.kernel.org
Commit 6fffb77c (USB: ohci-at91: fix PIO handling in relation with number of
ports) started setting unused pins to EINVAL. But this exposed a bug in the
ohci_hcd_at91_overcurrent_irq function where the gpio was used without being
checked to see if it is valid.
This patches fixed the issue by adding the gpio valid check.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com> Cc: stable <stable@vger.kernel.org> # [3.4+] whereever 6fffb77c went Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The three Pantech devices UML190 (106c:3716), UML290 (106c:3718) and
P4200 (106c:3721) all use the same subclasses to identify vendor
specific functions. Replace the existing device specific entries
with generic vendor matching, adding support for the P4200.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: stable <stable@vger.kernel.org> Cc: Thomas Schäfer <tschaefer@t-online.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Wed, 19 Sep 2012 21:02:29 +0000 (17:02 -0400)]
USB: EHCI: convert warning messages to debug-level
This patch (as1606) converts two warning messages in the ehci-hcd
driver to debug messages, and adds a little extra information to each.
The log messages occur when an EHCI controller takes too long (more
than 20 ms) to turn its async or periodic schedule on or off. If this
happens at all, it's liable to happen quite often and there's no point
spamming the system log with these warnings. Furthermore, there's
nothing much we can do about it when the problem happens.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-and-tested-by: Thomas Voegtle <tv@lio96.de> Cc: stable <stable@vger.kernel.org> # [3.6] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Wed, 19 Sep 2012 21:00:55 +0000 (17:00 -0400)]
USB: EHCI: remove useless test
This patch (as1605) removes a useless test from the EHCI debugfs
code. There's no point checking whether p.qh is non-NULL; we already
know it is and in any case it gets dereferenced aerlier in the
function.
drivers/usb/serial/usb-serial.c:1415:3-51: code aligned with following code on line 1416
vim +1415 drivers/usb/serial/usb-serial.c
1412 /* we only set the reset_resume field if the serial_driver has one */
1413 for (sd = serial_drivers; *sd; ++sd) {
1414 if ((*sd)->reset_resume)
> 1415 udriver->reset_resume = usb_serial_reset_resume;
> 1416 break;
1417 }
Jim Lin [Tue, 18 Sep 2012 08:42:17 +0000 (16:42 +0800)]
USB: EHCI: Tegra: Fix wrong register definition
Fix the issue that EHCI registers, hostpc[0] and usbmode_ex,
are not correctly accessed on Tegra3 platform.
Signed-off-by: Jim Lin <jilin@nvidia.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds new functions to upload firmware to the controller. The
drivers currently using ezusb are adapted to use these new functions.
This also fixes a bug occuring during firmware loading in the
whiteheat-driver:
The driver iterates over an ihex-formatted firmware using ++ on a "const
struct ihex_binrec*" which leads to faulty results, because ihex data is
read as length. The function "ihex_next_binrec(record)" has so be used
to work correctly
Signed-off-by: René Bürgel <rene.buergel@sohard.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This Patch adds support for the newer Cypress FX2LP. It also adapts
three drivers currently using ezusb to the interface change. (whiteheat
and keyspan[_pda])
Signed-off-by: René Bürgel <rene.buergel@sohard.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Beulich [Tue, 18 Sep 2012 11:23:02 +0000 (12:23 +0100)]
USB EHCI/Xen: propagate controller reset information to hypervisor
Just like for the in-tree early console debug port driver, the
hypervisor - when using a debug port based console - also needs to be
told about controller resets, so it can suppress using and then
re-initialize the debug port accordingly.
Other than the in-tree driver, the hypervisor driver actually cares
about doing this only for the device where the debug is port actually
in use, i.e. it needs to be told the coordinates of the device being
reset (quite obviously, leveraging the addition done for that would
likely benefit the in-tree driver too).
Signed-off-by: Jan Beulich <jbeulich@suse.com> Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: ti_usb_3410_5052: fix up noisy printk() usage
The driver should not be sending any printk() messages when it is
loaded, as no other USB serial driver does. This fixes that, and also
removes the useless version number from the driver.
Cc: Johan Hovold <jhovold@gmail.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Adhir Ramjiawan <adhirramjiawan0@gmail.com> Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was calling printk() directly at startup, which is just
noise. Switch over to using pr_info() where needed, and get rid of the
totally useless version number that had never ever been incremented.
Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: kobil_sct: switch 4 remaining printk() calls to use dev_dbg
These somehow got missed previously (as they weren't calling dbg(), but
rather printk() directly), so move over to using dev_dbg() as we never
want to see startup messages unless debugging is enabled.
Cc: Johan Hovold <jhovold@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try
to use it.
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Support Department <support@connecttech.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Adhir Ramjiawan <adhirramjiawan0@gmail.com> CC: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au> CC: Johan Hovold <jhovold@gmail.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Alan Stern <stern@rowland.harvard.edu> CC: "Bjørn Mork" <bjorn@mork.no> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: Wang YanQing <Udknight@gmail.com> CC: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: Mark Ferrell <mferrell@uplogix.com> CC: Donald Lee <donald@asix.com.tw> CC: Tony Zelenoff <antonz@parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au> CC: Johan Hovold <jhovold@gmail.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: "Eric W. Biederman" <ebiederm@xmission.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Matthias Bruestle and Harald Welte <support@reiner-sct.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Johan Hovold <jhovold@gmail.com> CC: Alan Stern <stern@rowland.harvard.edu> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: William Greathouse <wgreathouse@smva.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
Now that all usb-serial modules are only using dev_dbg()
the debug module parameter does not do anything at all, so
remove it to reduce any confusion if someone were to try to
use it.
CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> CC: "Justin P. Mattock" <justinmattock@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: serial: remove debug parameter from usb_serial_debug_data()
We should use dev_dbg() for usb_serial_debug_data() like all of the rest
of the usb-serial drivers use, so remove the debug parameter as it's not
needed.
Here's a driver for the Vizzini USB to serial device.
It looks to be copied from cdc-acm, and probably can be cleaned up a lot
more. Also, there's some odd "try to grab another interface" that is
probably wrong. And, if this really is a cdc-acm device, it probably
should just be a quirk of the cdc-acm device, but I can't figure that
out, and people have been using this driver for a long time now. So
merge it to let people use their hardware and clean it up over time.
Driver written by Rob Duncan but cleaned up and forward ported to the
latest kernel tree by me.
Cc: Rob Duncan <rob.duncan@exar.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull mfd fixes from Samuel Ortiz:
"This is the remaining MFD fixes for 3.6, with 5 pending fixes:
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to
initialize the watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device
addition API in order to prevent silent and potentially harmful
remapping behaviour changes for drivers supporting non-DT
platforms."
* tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: MAX77693: Fix NULL pointer error when initializing irqs
mfd: MAX77693: Fix interrupt handling bug
mfd: core: Push irqdomain mapping out into devices
mfd: lpc_ich: Fix a 3.5 kernel regression for iTCO_wdt driver
mfd: Move tps65217 regulator plat data handling to regulator
Merge tag 'for-3.6-rc6' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm fixes from Thierry Reding:
"While this comes a bit later than I had wished, both patches are
rather minor and touch only new drivers so I think these are still
safe for merging."
* tag 'for-3.6-rc6' of git://gitorious.org/linux-pwm/linux-pwm:
pwm: pwm-tiehrpwm: Fix conflicting channel period setting
pwm: pwm-tiecap: Disable APWM mode after configure
Pull scsi target fixes from Nicholas Bellinger:
"Here is the current set of target-pending fixes headed for v3.6-final
The main parts of this series include bug-fixes from Paolo Bonzini to
address an use-after-free bug in pSCSI sense exception handling, along
with addressing some long-standing bugs wrt the handling of zero-
length SCSI CDB payloads also specific to pSCSI pass-through device
backends."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: go through normal processing for zero-length REQUEST_SENSE
target: support zero allocation length in REQUEST SENSE
target: support zero-size allocation lengths in transport_kmap_data_sg
target: fail REPORT LUNS with less than 16 bytes of payload
target: report too-small parameter lists everywhere
target: go through normal processing for zero-length PSCSI commands
target: fix use-after-free with PSCSI sense data
target: simplify code around transport_get_sense_data
target: move transport_get_sense_data
target: Check idr_get_new return value in iscsi_login_zero_tsih_s1
target: Fix ->data_length re-assignment bug with SCSI overflow
Merge tag 'pm-for-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
"Three ACPI device power management fixes related to checking and
setting device power states."
* tag 'pm-for-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Use KERN_DEBUG when no power resources are found
ACPI / PM: Fix resource_lock dead lock in acpi_power_on_device
ACPI / PM: Infer parent power state from child if unknown, v2
Merge tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull more sound fixes from Takashi Iwai:
"Yet more (a bunch of) small fixes that slipped from the previous pull
request. Most of commits are pending ASoC fixes, all of which are
fairly trivial commits."
* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8904: correct the index
ALSA: hda - Yet another position_fix quirk for ASUS machines
ASoC: tegra: fix maxburst settings in dmaengine code
ASoC: samsung dma - Don't indicate support for pause/resume.
ASoC: mc13783: Remove mono support
ASoC: arizona: Fix typo in 44.1kHz rates
ASoC: spear: correct the check for NULL dma_buffer pointer
sound: tegra_alc5632: remove HP detect GPIO inversion
ASoC: atmel-ssc: include linux/io.h for raw io
ASoC: dapm: Don't force card bias level to be updated
ASoC: dapm: Make sure we update the bias level for CODECs with no op
ASoC: am3517evm: fix error return code
ASoC: ux500_msp_i2s: better use devm functions and fix error return code
ASoC: imx-sgtl5000: fix error return code
Nikolay Ulyanitsky reported thatthe 3.6-rc5 kernel has a 15-20%
performance drop on PostgreSQL 9.2 on his machine (running "pgbench").
Borislav Petkov was able to reproduce this, and bisected it to this
commit 970e178985ca ("sched: Improve scalability via 'CPU buddies' ...")
apparently because the new single-idle-buddy model simply doesn't find
idle CPU's to reschedule on aggressively enough.
Mike Galbraith suspects that it is likely due to the user-mode spinlocks
in PostgreSQL not reacting well to preemption, but we don't really know
the details - I'll just revert the commit for now.
There are hopefully other approaches to improve scheduler scalability
without it causing these kinds of downsides.
Reported-by: Nikolay Ulyanitsky <lystor@gmail.com> Bisected-by: Borislav Petkov <bp@alien8.de> Acked-by: Mike Galbraith <efault@gmx.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chanwoo Choi [Tue, 21 Aug 2012 06:16:23 +0000 (15:16 +0900)]
mfd: MAX77693: Fix NULL pointer error when initializing irqs
This patch initialize register map of MUIC device because mfd driver
of Maxim MAX77693 use regmap-muic instance of MUIC device when irqs of
Maxim MAX77693 is initialized before call max77693-muic probe() function.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Chanwoo Choi [Tue, 21 Aug 2012 06:15:52 +0000 (15:15 +0900)]
mfd: MAX77693: Fix interrupt handling bug
This patch fix bug related to interrupt handling for MAX77693 devices.
- Unmask interrupt masking bit for charger/flash/muic to revolve
that interrupt isn't happened when external connector is attached.
- Fix wrong regmap instance when muic interrupt is happened.
This patch were discussed and confirm discussion about this patch on below url:
http://lkml.org/lkml/2012/7/16/118
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Tue, 11 Sep 2012 07:16:36 +0000 (15:16 +0800)]
mfd: core: Push irqdomain mapping out into devices
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties. This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern. There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.
Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts. The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Merge tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for 3.6
A bigger set of updates than I'm entirely comfortable with - things
backed up a bit due to travel. As ever the majority of these are small,
focused updates for specific drivers though there are a couple of core
changes. There's been good exposure in -next.
Pull GFS2 fixes from Steven Whitehouse:
"Here are three GFS2 fixes for the current kernel tree. These are all
related to the block reservation code which was added at the merge
window. That code will be getting an update at the forthcoming merge
window too. In the mean time though there are a few smaller issues
which should be fixed.
The first patch resolves an issue with write sizes of greater than 32
bits with the size hinting code. The second ensures that the
allocation data structure is initialised when using xattrs and the
third takes into account allocations which may have been made by other
nodes which affect a reservation on the local node."
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Take account of blockages when using reserved blocks
GFS2: Fix missing allocation data for set/remove xattr
GFS2: Make write size hinting code common
Merge branch 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86
Pull x86 platform driver updates from Matthew Garrett:
"A few small updates for 3.6 - a trivial regression fix and a couple of
conformance updates for the gmux driver, plus some tiny fixes for
asus-wmi, eeepc-laptop and thinkpad_acpi."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
thinkpad_acpi: buffer overflow in fan_get_status()
eeepc-laptop: fix device reference count leakage in eeepc_rfkill_hotplug()
platform/x86: fix asus_laptop.wled_type description
asus-laptop: HRWS/HWRS typo
drivers-platform-x86: remove useless #ifdef CONFIG_ACPI_VIDEO
apple-gmux: Fix port address calculation in gmux_pio_write32()
apple-gmux: Fix index read functions
apple-gmux: Obtain version info from indexed gmux
Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pull i2c embedded fixes from Wolfram Sang:
"The last bunch of (typical) i2c-embedded driver fixes for 3.6.
Also update the MAINTAINERS file to point to my tree since people keep
asking where to find their patches."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: algo: pca: Fix mode selection for PCA9665
MAINTAINERS: fix tree for current i2c-embedded development
i2c: mxs: correctly setup speed for non devicetree
i2c: pnx: Fix read transactions of >= 2 bytes
i2c: pnx: Fix bit definitions
Merge tag 'ecryptfs-3.6-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull ecryptfs fixes from Tyler Hicks:
- Fixes a regression, introduced in 3.6-rc1, when a file is closed
before its shared memory mapping is dirtied and unmapped. The lower
file was being released when the eCryptfs file was closed and the
dirtied pages could not be written out.
- Adds a call to the lower filesystem's ->flush() from
ecryptfs_flush().
- Fixes a regression, introduced in 2.6.39, when a file is renamed on
top of another file. The target file's inode was not being evicted
and the space taken by the file was not reclaimed until eCryptfs was
unmounted.
* tag 'ecryptfs-3.6-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: Copy up attributes of the lower target inode after rename
eCryptfs: Call lower ->flush() from ecryptfs_flush()
eCryptfs: Write out all dirty pages just before releasing the lower file
Merge branch 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull one more DMA-mapping fix from Marek Szyprowski:
"This patch fixes very subtle bug (typical off-by-one error) which
might appear in very rare circumstances."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
arm: mm: fix DMA pool affiliation check
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix word size register read and write operations in ina2xx driver, and
initialize uninitialized structure elements in twl4030-madc-hwmon
driver."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ina2xx) Fix word size register read and write operations
hwmon: (twl4030-madc-hwmon) Initialize uninitialized structure elements
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"I realise this a bit bigger than I would want at this point.
Exynos is a large chunk, I got them to half what they wanted already,
and hey its ARM based, so not going to hurt many people.
Radeon has only two fixes, but the PLL fixes were a bit bigger, but
required for a lot of scenarios, the fence fix is really urgent.
vmwgfx: I've pulled in a dumb ioctl support patch that I was going to
shove in later and cc stable, but we need it asap, its mainly to stop
mesa growing a really ugly dependency in userspace to run stuff on
vmware, and if I don't stick it in the kernel now, everyone will have
to ship ugly userspace libs to workaround it.
nouveau: single urgent fix found in F18 testing, causes X to not start
properly when f18 plymouth is used
i915: smattering of fixes and debug quieting
gma500: single regression fix
So as I said a bit large, but its fairly well scattered and its all
stuff I'll be shipping in F18's 3.6 kernel."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (26 commits)
drm/nouveau: fix booting with plymouth + dumb support
drm/radeon: make 64bit fences more robust v3
drm/radeon: rework pll selection (v3)
drm: Drop the NV12M and YUV420M formats
drm/exynos: remove DRM_FORMAT_NV12M from plane module
drm/exynos: fix double call of drm_prime_(init/destroy)_file_private
drm/exynos: add dummy support for dmabuf-mmap
drm/exynos: Add missing braces around sizeof in exynos_mixer.c
drm/exynos: Add missing braces around sizeof in exynos_hdmi.c
drm/exynos: Make g2d_pm_ops static
drm/exynos: Add dependency for G2D in Kconfig
drm/exynos: fixed page align bug.
drm/exynos: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/exynos: Use devm_* functions in exynos_drm_g2d.c file
drm/exynos: Use devm_kzalloc in exynos_drm_hdmi.c file
drm/exynos: Use devm_kzalloc in exynos_drm_vidi.c file
drm/exynos: Remove redundant check in exynos_drm_fimd.c file
drm/exynos: Remove redundant check in exynos_hdmi.c file
vmwgfx: add dumb ioctl support
gma500: Fix regression on Oaktrail devices
...
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"This tree includes various fixes"
Ingo really needs to improve on the whole "explain git pull" part.
"Various fixes" indeed.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/hwpb: Invoke __perf_event_disable() if interrupts are already disabled
perf/x86: Enable Intel Cedarview Atom suppport
perf_event: Switch to internal refcount, fix race with close()
oprofile, s390: Fix uninitialized memory access when writing to oprofilefs
perf/x86: Fix microcode revision check for SNB-PEBS
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Johan Hovold <jhovold@gmail.com> CC: Mark Ferrell <mferrell@uplogix.com> CC: Donald Lee <donald@asix.com.tw> CC: Tony Zelenoff <antonz@parallels.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge tag 'usb-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are a number of USB patches, a bit more than I normally like this
late in the -rc series, but given people's vacations (myself
included), and the kernel summit, it seems to have happened this way.
All are tiny, but they add up. A number of gadget and xhci fixes, and
a few new device ids. All have been tested in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: don't stall endpoint if request list is empty in isr_tr_complete_low
usb: chipidea: cleanup dma_pool if udc_start() fails
usb: chipidea: udc: fix error path in udc_start()
usb: chipidea: udc: add pullup fuction, needed by the uvc gadget
usb: chipidea: udc: fix setup of endpoint maxpacket size
USB: option: replace ZTE K5006-Z entry with vendor class rule
EHCI: Update qTD next pointer in QH overlay region during unlink
USB: cdc-wdm: fix wdm_find_device* return value
USB: ftdi_sio: do not claim CDC ACM function
usb: dwc3: gadget: fix pending isoc handling
usb: renesas_usbhs: fixup DMA transport data alignment
usb: gadget: at91udc: Don't check for ep->ep.desc
usb: gadget: at91udc: don't overwrite driver data
usb: dwc3: core: fix incorrect usage of resource pointer
usb: musb: musbhsdma: fix IRQ check
usb: musb: tusb6010: fix error path in tusb_probe()
usb: musb: host: fix for musb_start_urb Oops
usb: gadget: dummy_hcd: add support for USB_DT_BOS on rh
usb: gadget: dummy_hcd: fixup error probe path
usb: gadget: s3c-hsotg.c: fix error return code
...
Merge tag 'driver-core-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg Kroah-Hartman:
"Here is one fix for 3.6-rc6 for the kobject.h file.
It fixes a reported oops if CONFIG_HOTPLUG is disabled. It's been in
the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: fix oops with "input0: bad kobj_uevent_env content in show_uevent()"
vfs: make O_PATH file descriptors usable for 'fstat()'
We already use them for openat() and friends, but fstat() also wants to
be able to use O_PATH file descriptors. This should make it more
directly comparable to the O_SEARCH of Solaris.
Note that you could already do the same thing with "fstatat()" and an
empty path, but just doing "fstat()" directly is simpler and faster, so
there is no reason not to just allow it directly.
See also commit 332a2e1244bd, which did the same thing for fchdir, for
the same reasons.
Reported-by: ольга крыжановская <olga.kryzhanovska@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: stable@kernel.org # O_PATH introduced in 3.0+ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Alan Stern <stern@rowland.harvard.edu> CC: Rusty Russell <rusty@rustcorp.com.au> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Rusty Russell <rusty@rustcorp.com.au> CC: Alan Stern <stern@rowland.harvard.edu> CC: Mauro Carvalho Chehab <mchehab@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the dbg() macro is no longer being used in the driver,
the debug module parameter doesn't do anything at all. So remove
it so as to not confuse people.
CC: Bill Pemberton <wfp5p@virginia.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / karo-tx-linux.git / log