Ondrej Zary [Tue, 27 Sep 2016 19:00:25 +0000 (21:00 +0200)]
scsi: g_NCR5380: Stop using scsi_module.c
Convert g_NCR5380 to use scsi_add_host instead of scsi_module.c Use
pnp_driver and isa_driver to manage cards.
In order to support multiple cards, new module parameter format is
introduced. The old parameters are kept for compatibility.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ondrej Zary [Tue, 27 Sep 2016 19:00:24 +0000 (21:00 +0200)]
scsi: g_NCR5380: Reduce overrides[] from array to struct
Remove compile-time card type definition GENERIC_NCR5380_OVERRIDE. Then
remove all code iterating the overrides[] array and reduce it to struct
card.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ondrej Zary [Tue, 27 Sep 2016 19:00:23 +0000 (21:00 +0200)]
scsi: g_NCR5380: Remove deprecated __setup
Remove deprecated __setup for parsing command line parameters.
g_NCR5380.* parameters could be used instead.
This might break existing setups with g_NCR5380 built-in (if there are
any). But it has to go in order to remove the overrides[] array.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Lee Duncan [Mon, 26 Sep 2016 22:25:30 +0000 (15:25 -0700)]
MAINTAINERS: Update open-iscsi maintainers
Chris Leech and I are taking over as open-iscsi maintainers.
Signed-off-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: be2iscsi: mark symbols static where possible
We get 6 warnings when building kernel with W=1:
drivers/scsi/be2iscsi/be_main.c:65:1: warning: no previous prototype for 'beiscsi_log_enable_disp' [-Wmissing-prototypes]
drivers/scsi/be2iscsi/be_main.c:78:1: warning: no previous prototype for 'beiscsi_log_enable_change' [-Wmissing-prototypes]
drivers/scsi/be2iscsi/be_main.c:97:1: warning: no previous prototype for 'beiscsi_log_enable_store' [-Wmissing-prototypes]
drivers/scsi/be2iscsi/be_main.c:116:1: warning: no previous prototype for 'beiscsi_log_enable_init' [-Wmissing-prototypes]
drivers/scsi/be2iscsi/be_main.c:4587:5: warning: no previous prototype for 'beiscsi_iotask_v2' [-Wmissing-prototypes]
drivers/scsi/be2iscsi/be_main.c:4976:6: warning: no previous prototype for 'beiscsi_hba_attrs_init' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static. So this
patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Reviewed-by: Jitendra Bhivare <Jitendra.bhivare@broadcom> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get a few warnings when building kernel with W=1:
drivers/scsi/mvsas/mv_sas.c:77:18: warning: no previous prototype for 'mvs_find_dev_mvi' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:105:5: warning: no previous prototype for 'mvs_find_dev_phyno' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1161:20: warning: no previous prototype for 'mvs_alloc_dev' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1178:6: warning: no previous prototype for 'mvs_free_dev' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1188:5: warning: no previous prototype for 'mvs_dev_found_notify' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1244:6: warning: no previous prototype for 'mvs_dev_gone_notify' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1614:6: warning: no previous prototype for 'mvs_set_sense' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_sas.c:1653:6: warning: no previous prototype for 'mvs_fill_ssp_resp_iu' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_64xx.c:139:6: warning: no previous prototype for 'mvs_64xx_clear_srs_irq' [-Wmissing-prototypes]
drivers/scsi/mvsas/mv_64xx.c:566:6: warning: no previous prototype for 'mvs_64xx_make_prd' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static. So this
patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get 2 warnings when building kernel with W=1:
drivers/scsi/pm8001/pm8001_sas.c:530:23: warning: no previous prototype for 'pm8001_alloc_dev' [-Wmissing-prototypes]
drivers/scsi/pm8001/pm8001_hwi.c:4495:5: warning: no previous prototype for 'pm8001_chip_phy_stop_req' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static. So this
patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Acked-by: Lindar Liu <lindar_liu@usish.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do the user_len check first and then the ver_addr allocation so that we
can save us the kfree() on the error path when user_len is >
ARCMSR_API_DATA_BUFLEN.
Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Marco Grassi <marco.gra@gmail.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Tomas Henzl <thenzl@redhat.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: <stable@vger.kernel.org> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Vincent Stehlé [Wed, 21 Sep 2016 20:54:07 +0000 (22:54 +0200)]
scsi: fcoe: fix off by one in eth2fc_speed()
This should be "< ARRAY_SIZE()" instead of "<= ARRAY_SIZE()".
Fixes: 0b924e5505a568e7 ("scsi: fcoe: provide translation table between Ethernet and FC port speeds") Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinicke <hare@suse.de> Acked-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinicke <hare@suse.de> Acked-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinicke <hare@suse.de> Acked-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinicke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinicke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinicke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has not seen any maintainer activity or other work that
wasn't tree wide conversion or clenaups in the entire history of
the git tree.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinicke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get a few warnings when building kernel with W=1:
drivers/scsi/lpfc/lpfc_sli.c:5693:1: warning: no previous prototype for 'lpfc_set_features' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:8972:1: warning: no previous prototype for 'lpfc_sli_calc_ring' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4621:1: warning: no previous prototype for 'lpfc_rdp_res_link_service' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4633:1: warning: no previous prototype for 'lpfc_rdp_res_sfp_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4698:1: warning: no previous prototype for 'lpfc_rdp_res_link_error' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4727:1: warning: no previous prototype for 'lpfc_rdp_res_bbc_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4752:1: warning: no previous prototype for 'lpfc_rdp_res_oed_temp_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4780:1: warning: no previous prototype for 'lpfc_rdp_res_oed_voltage_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4809:1: warning: no previous prototype for 'lpfc_rdp_res_oed_txbias_desc' [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_els.c:4838:1: warning: no previous prototype for 'lpfc_rdp_res_oed_txpower_desc' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static. So this
patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Tue, 20 Sep 2016 20:42:30 +0000 (15:42 -0500)]
scsi: hpsa: correct call to hpsa_do_reset
calling fill_cmd() using a MACRO definition not handled in switch
statement causes BUG() to be called.
Signed-off-by: Don Brace <don.brace@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kiwoong Kim [Thu, 8 Sep 2016 23:22:22 +0000 (08:22 +0900)]
scsi: ufs: Get a TM service response from the correct offset
When any UFS host controller receives a TM(Task Management) response
from a UFS device, UFS driver has been recognize like receiving a
message of "Task Management Function Complete"(00h) in all cases, so
far. That means there is no pending task for a tag of the TM request
sent before in the UFS device. That's because the byte offset 6 in TM
response which has been used to get a TM service response so far
represents just whether or not a TM transmission passes.
Regarding UFS spec, the correct byte offset to get TM service response
is 15, not 6.
I tested that UFS driver responds properly for the TM response from a
UFS device with an reference board with exynos8890, as follow: No
pending task -> Task Management Function Complete (00h) Pending task ->
Task Management Function Succeeded (08h)
[mkp: applied by hand]
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com> Signed-off-by: HeonGwang Chu <hg.chu@samsung.com> Tested-by: : Kiwoong Kim <kwmad.kim@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Brian King [Mon, 19 Sep 2016 13:59:19 +0000 (08:59 -0500)]
scsi: ibmvfc: Fix I/O hang when port is not mapped
If a VFC port gets unmapped in the VIOS, it may not respond with a CRQ
init complete following H_REG_CRQ. If this occurs, we can end up having
called scsi_block_requests and not a resulting unblock until the init
complete happens, which may never occur, and we end up hanging I/O
requests. This patch ensures the host action stay set to
IBMVFC_HOST_ACTION_TGT_DEL so we move all rports into devloss state and
unblock unless we receive an init complete.
Cc: <stable@vger.kernel.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: megaraid_sas: clean function declarations in megaraid_sas_base.c up
We get a few warnings when building kernel with W=1:
drivers/scsi/megaraid/megaraid_sas_fusion.c:281:1: warning: no previous prototype for 'megasas_free_cmds_fusion' [-Wmissing-prototypes]
drivers/scsi/megaraid/megaraid_sas_fusion.c:714:1: warning: no previous prototype for 'megasas_ioc_init_fusion' [-Wmissing-prototypes]
....
In fact, these functions are declared in
drivers/scsi/megaraid/megaraid_sas_base.c, but should be declared in a
header file, thus can be recognized in other file.
So this patch adds the declarations into
drivers/scsi/megaraid/megaraid_sas_fusion.h.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Brian King [Fri, 16 Sep 2016 21:51:37 +0000 (16:51 -0500)]
scsi: ipr: Remove redundant messages at adapter init time
Whenever multiple HRRQs are enabled, which is the default setting now,
we end up seeing the following message logged prior to initialization of
each HRRQ:
Starting IOA initialization sequence
This results in 16 of these messages on most adapters, which serves
little purpose. Change to just log this once.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A 9084 error gets logged by the ipr adapter when adapter raw mode gets
enabled. A bunch of unformatted hex data also gets logged for this
error, which is of little use, so let's avoid logging it by default in
order to avoid the log getting polluted with useless data.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Reviewed-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
kevin Barnett [Fri, 16 Sep 2016 20:01:51 +0000 (15:01 -0500)]
scsi: smartpqi: raid bypass lba calculation fix
In the ioaccel path, the calculation of the starting LBA for
READ(6)/WRITE(6) SCSI commands does not take into account the most
significant 5 bits of the LBA: it only uses the least significant 16
bits of the starting LBA.
Reported-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Missing 5 bits of byte 1 in the LBA issued by SML.
Reported-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dan Carpenter [Thu, 15 Sep 2016 13:44:56 +0000 (16:44 +0300)]
scsi: arcmsr: Buffer overflow in arcmsr_iop_message_xfer()
We need to put an upper bound on "user_len" so the memcpy() doesn't
overflow.
Cc: <stable@vger.kernel.org> Reported-by: Marco Grassi <marco.gra@gmail.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: ibmvscsis: Fix error return code in ibmvscsis_probe()
Fix to return error code -ENOMEM from the dma mapping error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These should go together with the rest of the T10 protection information
defintions.
[mkp: s/T10_DIF/T10_PI/]
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: scsi_debug: Use struct t10_pi_tuple instead of struct sd_dif_tuple
And remove the declaration of the latter in sd.h as scsi_debug was the
only user.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Fri, 9 Sep 2016 21:30:42 +0000 (16:30 -0500)]
scsi: hpsa: Check for null devices in ioaccel submission patch
Reviewed-by: Scott Benesh <scott.benest@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scott Teel [Fri, 9 Sep 2016 21:30:36 +0000 (16:30 -0500)]
scsi: hpsa: Prevent sending bmic commands to externals
Reviewed-by: Scott Benesh <scott.benest@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Scott Teel [Fri, 9 Sep 2016 21:30:29 +0000 (16:30 -0500)]
scsi: hpsa: Check for vpd support before sending
Before using vendor-specific VPD pages for getting raid_level and
device_id, check for page support. If page isn't supported, don't try
to use it. Also, pay attention to return status on hpsa_get_device_id.
[mkp: fix boolean return warnings reported by kbuild test robot]
Reviewed-by: Scott Benesh <scott.benest@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Fri, 9 Sep 2016 21:30:23 +0000 (16:30 -0500)]
scsi: hpsa: Check for null device pointers
A device can be deleted causing NULL pointer issues.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Fri, 9 Sep 2016 21:30:17 +0000 (16:30 -0500)]
scsi: hpsa: Determine device external status earlier
Currently we are checking for external status before we are determining
if a device is an external device.
Reviewed-by: Scott Benesh <scott.benest@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Finn Thain [Wed, 31 Aug 2016 04:44:56 +0000 (14:44 +1000)]
scsi: ncr5380: Improve interrupt latency during PIO tranfers
Large PIO transfers are broken up into chunks to try to avoid disabling
local IRQs for long periods. But IRQs are still disabled for too long
and this causes SCC FIFO overruns during serial port transfers.
This patch reduces the PIO chunk size to reduce interrupt latency to
something on the order of milliseconds, at the expense of additional CPU
overhead from extra iterations of the NCR5380_main() loop.
That CPU overhead is a problem for slow machines (e.g. mac_scsi on 25
MHz 68030) but these machines generally use PDMA not PIO. This patch
doesn't make the overhead any worse on my Mac LC III (because it only
gets about 510 accesses per ms).
This patch decreases disk performance by a fraction of one percent for
dmx3191d on my 333 MHz PowerPC 750. Other affected hardware (such as
g_NCR5380 on x86) was not tested but 5380 ISA cards generally use PDMA
and not PIO.
[mkp: fix whitespace]
Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Reviewed-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Daniel Wagner [Tue, 13 Sep 2016 08:58:50 +0000 (10:58 +0200)]
scsi: virtio_scsi: Use complete() instead complete_all()
There is only one waiter for the completion, therefore there is no need
to use complete_all(). Let's make that clear by using complete() instead
of complete_all().
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Daniel Wagner [Tue, 13 Sep 2016 08:58:49 +0000 (10:58 +0200)]
scsi: sym53c8xx_2: Use complete() instead complete_all()
There is only one waiter for the completion, therefore there is no need
to use complete_all(). Let's make that clear by using complete() instead
of complete_all().
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Daniel Wagner [Tue, 13 Sep 2016 08:58:48 +0000 (10:58 +0200)]
scsi: csiostor: Fix completion usage
The (re)initializing of the completion object should be done before we
trigger the transfer. Doing this after triggering the hardware opens up
a race window. Without the timeout we would problaly even deadlock. Use
also reinit_completion because we initalize the whole data structure in
csio_scscim_init().
There is only one waiter for the completion, therefore there is no need
to use complete_all(). Let's make that clear by using complete() instead
of complete_all().
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Mon, 12 Sep 2016 12:42:12 +0000 (13:42 +0100)]
scsi: megaraid_sas: add in missing white space in error message text
A dev_printk message spans two lines and the literal string is missing a
white space between words. Add the white space.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:25 +0000 (23:36 +0800)]
scsi: hisi_sas: send three identify before phy up
When the v2 hw is attached with many disks through an expander, there
may be OOB reset resulting in a PHY going down after the speed is
negotiated (very low probability).
This issue is resolved by modifying the link control registers to send
three identify frames before the PHY is ready (according to 6.10.3.3.2
in SAS 3.0 spec) and close ready when the PHY is down.
Signed-off-by: NengLong Zhao <zhaonenglong@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:24 +0000 (23:36 +0800)]
scsi: hisi_sas: add missing SATA pending device type to v2 hw
In setup_itct_v2_hw(), SATA device type SAS_SATA_PENDING is missing, so
add it.
Note: The HiSi SAS controller does not support SATA PM, so do not handle
SAS_SATA_PM_PORT or SAS_SATA_PM.
Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:23 +0000 (23:36 +0800)]
scsi: hisi_sas: remove init_id_frame_v1_hw()
Function config_id_frame_v1_hw() is called twice for each PHY during
initialisation, which is unneeded.
So remove init_id_frame_v1_hw(), which only calls
config_id_frame_v1_hw().
We will keep the call to config_id_frame_v1_hw() in start_phy_v1_hw()
since it will be used for PHY reset functions.
Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:22 +0000 (23:36 +0800)]
scsi: hisi_sas: remove init_id_frame_v2_hw()
Function config_id_frame_v2_hw() is called twice for each PHY during
initialisation, which is unneeded.
So remove init_id_frame_v2_hw(), which only calls
config_id_frame_v2_hw().
We will keep the call to config_id_frame_v2_hw() in start_phy_v2_hw()
since it will be used for PHY reset functions.
Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:21 +0000 (23:36 +0800)]
scsi: hisi_sas: fix HBA SAS addr endianness for v1 hw
The endianness for the SAS address in the TX_ID_DWORD registers is set
incorrectly. We see errors like this in the boot log for v2 hw (which
would have the same issue as v1 hw):
[ 7.583284] sas: target proto 0x0 at 50000d1108e7923f:0x1f not handled
This is due to the host SAS addr not matching the PHY SAS addr in the
expander host-attached phy discovery responses.
To fix, we byte swap the SAS addr from BE to LE (which is the endianness
of the SAS controller).
Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:20 +0000 (23:36 +0800)]
scsi: hisi_sas: fix HBA SAS addr endianness for v2 hw
The endianness for the SAS address in the TX_ID_DWORD registers is set
incorrectly. We see errors like this in the boot log:
[ 7.583284] sas: target proto 0x0 at 50000d1108e7923f:0x1f not handled
This is due to the host SAS addr not matching the PHY SAS addr in the
expander host-attached phy discovery responses.
To fix, we byte swap the SAS addr from BE to LE (which is the endianness
of the SAS controller).
Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:19 +0000 (23:36 +0800)]
scsi: hisi_sas: set dma mask before allocate DMA memory
The device DMA mask was being set after the bulk of the DMA allocations
in the driver init, so potentially DMA allocates fail. To resolve,
relocate before allocating the DMA memory when initialising the driver.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:18 +0000 (23:36 +0800)]
scsi: hisi_sas: fix a potential warning for sata disk ejection
If hisi_sas_task_prep() fails for a SATA device due to PHY down, we
return a failure to libata and also call task_done(), which will cause
ata_qc_complete() to be called twice: - first call from
hisi_sas_task_prep(), which will clear flag ATA_QCFLAG_ACTIVE -
ata_qc_complete() called from libata The warning call trace is as
follows:
The issue is resolved by simply returning a failure status code to the
upper layer.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:17 +0000 (23:36 +0800)]
scsi: hisi_sas: fix phy8 linkrate calculation in phy_up_v2_hw()
In function phy_up_v2_hw(), we needlessly recalculate the phy linkrate
for all phys, and the calculation is incorrect for phy8, so remove this
code.
Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:16 +0000 (23:36 +0800)]
scsi: hisi_sas: disable dlvry queues once at reset for v2 hw
The Delivery queue enable register should only be written to once at
reset for v2 hw.
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:15 +0000 (23:36 +0800)]
scsi: hisi_sas: use safe BITS_PER_BYTE for slot tag size calculation
The memory calculation for the tags bitmap should use BITS_PER_BYTE
macro instead of coincidental same value of sizeof(unsigned long).
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:14 +0000 (23:36 +0800)]
scsi: hisi_sas: only zero slot memory when reused
Currently the slot memory is zeroed when it is freed and also when it is
reused, like in hisi_sas_task_prep(). Optimise by avoiding the redundant
zeroing in the free.
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:13 +0000 (23:36 +0800)]
scsi: hisi_sas: keep CHL_INT2 masked for v2 HW
None of the CHL_INT2 interrupts are serviced in the channel irq ISR, so
leave the interrupt source masked. The interrupt mask is initially set
in init_reg_v2_hw().
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:12 +0000 (23:36 +0800)]
scsi: hisi_sas: save delivery queue write pointer
Optimise by saving an avoidable read in the get_free_slot function. The
delivery queue write pointer will only be updated by software, so don't
bother re-reading what was already written in the previous call to
start_delivery function.
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Tue, 6 Sep 2016 15:36:11 +0000 (23:36 +0800)]
scsi: hisi_sas: save completion queue read pointer
Optimise by saving an avoidable read in the cq interrupt. The queue
read pointer will only be updated by software, so don't bother
re-reading what was already written in the previous interrupt.
Signed-off-by: John Garry <john.garry@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Matthew R. Ochs [Fri, 2 Sep 2016 20:40:41 +0000 (15:40 -0500)]
scsi: cxlflash: Fix context reference tracking on detach
Commit 888baf069f49 ("scsi: cxlflash: Add kref to context") introduced a
kref to the context. In particular, the detach routine was updated to
use the kref services for managing the removal and destruction of a
context.
As part of this change, the tracking mechanism internal to the detach
handler was refactored. This introduced a bug that can cause the
tracking state to be lost. This can lead to a situation where exclusive
access to a context is prematurely [and unknowingly] relinquished for
the executing thread.
To remedy, only update the tracking state when the kref operation
indicates the context was removed.
Fixes: 888baf069f49 ("scsi: cxlflash: Add kref to context") Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Matthew R. Ochs [Fri, 2 Sep 2016 20:40:20 +0000 (15:40 -0500)]
scsi: cxlflash: Refactor WWPN setup
Commit 964497b3bf3f ("cxlflash: Remove dual port online dependency")
logically removed the ability for the WWPN setup routine afu_set_wwpn()
to return a non-success value. This routine can safely be made a void to
simplify the code as there is no longer a need to report a failure.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Matthew R. Ochs [Fri, 2 Sep 2016 20:40:03 +0000 (15:40 -0500)]
scsi: cxlflash: Improve EEH recovery time
When an EEH occurs during device initialization, the port timeout logic
can cause excessive delays as MMIO reads will fail. Depending on where
they are experienced, these delays can lead to a prolonged reset,
causing an unnecessary triggering of other timeout logic in the SCSI
stack or user applications.
To expedite recovery, the port timeout logic is updated to decay the
timeout at a much faster rate when in the presence of a likely EEH
frozen event.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Matthew R. Ochs [Fri, 2 Sep 2016 20:39:30 +0000 (15:39 -0500)]
scsi: cxlflash: Fix to avoid EEH and host reset collisions
The EEH reset handler is ignorant to the current state of the driver
when processing a frozen event and initiating a device reset. This can
be an issue if an EEH event occurs while a user or stack initiated reset
is executing. More specifically, if an EEH occurs while the SCSI host
reset handler is active, the reset initiated by the EEH thread will
likely collide with the host reset thread. This can leave the device in
an inconsistent state, or worse, cause a system crash.
As a remedy, the EEH handler is updated to evaluate the device state and
take appropriate action (proceed, wait, or disconnect host). The host
reset handler is also updated to handle situations where an EEH occurred
during a host reset. In such situations, the host reset handler will
delay reporting back a success to give the EEH reset an opportunity to
complete.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Fri, 2 Sep 2016 20:39:16 +0000 (15:39 -0500)]
scsi: cxlflash: Remove the device cleanly in the system shutdown path
Commit 704c4b0ddc03 ("cxlflash: Shutdown notify support for CXL Flash
cards") was recently introduced to notify the AFU when a system is going
down. Due to the position of the cxlflash driver in the device stack,
cxlflash devices are _always_ removed during a reboot/shutdown. This can
lead to a crash if the cxlflash shutdown hook is invoked _after_ the
shutdown hook for the owning virtual PHB. Furthermore, the current
implementation of shutdown/remove hooks for cxlflash are not tolerant to
being invoked when the device is not enabled. This can also lead to a
crash in situations where the remove hook is invoked after the device
has been removed via the vPHBs shutdown hook. An example of this
scenario would be an EEH reset failure while a reboot/shutdown is in
progress.
To solve both problems, the shutdown hook for cxlflash is updated to
simply remove the device. This path already includes the AFU
notification and thus this solution will continue to perform the
original intent. At the same time, the remove hook is updated to protect
against being called when the device is not enabled.
Fixes: 704c4b0ddc03 ("cxlflash: Shutdown notify support for CXL Flash
cards") Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Uma Krishnan [Fri, 2 Sep 2016 20:38:48 +0000 (15:38 -0500)]
scsi: cxlflash: Scan host only after the port is ready for I/O
When a port link is established, the AFU sends a 'link up' interrupt.
After the link is up, corresponding initialization steps are performed
on the card. Following that, when the card is ready for I/O, the AFU
sends 'login succeeded' interrupt. Today, cxlflash invokes
scsi_scan_host() upon receipt of both interrupts.
SCSI commands sent to the port prior to the 'login succeeded' interrupt
will fail with 'port not available' error. This is not desirable.
Moreover, when async_scan is active for the host, subsequent scan calls
are terminated with error. Due to this, the scsi_scan_host() call
performed after 'login succeeded' interrupt could portentially return
error and the devices may not be scanned properly.
To avoid this problem, scsi_scan_host() should be called only after the
'login succeeded' interrupt.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get a few warnings when building kernel with W=1:
drivers/scsi/bnx2fc/bnx2fc_els.c:257:6: warning: no previous prototype for 'bnx2fc_srr_compl' [-Wmissing-prototypes]
drivers/scsi/bnx2fc/bnx2fc_els.c:367:6: warning: no previous prototype for 'bnx2fc_rec_compl' [-Wmissing-prototypes]
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:628:5: warning: no previous prototype for 'bnx2fc_percpu_io_thread' [-Wmissing-prototypes]
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:1413:26: warning: no previous prototype for 'bnx2fc_interface_create' [-Wmissing-prototypes]
drivers/scsi/bnx2fc/bnx2fc_hwi.c:997:21: warning: no previous prototype for 'bnx2fc_alloc_work' [-Wmissing-prototypes]
drivers/scsi/bnx2fc/bnx2fc_io.c:1082:5: warning: no previous prototype for 'bnx2fc_abts_cleanup' [-Wmissing-prototypes]
....
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static. so this
patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We get 1 warning when building kernel with W=1:
drivers/scsi/aacraid/src.c:616:5: warning: no previous prototype for 'aac_src_select_comm' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static. so this patch
marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Dave Carroll <david.carroll@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Baoyou Xie [Mon, 29 Aug 2016 10:19:00 +0000 (18:19 +0800)]
scsi: ufs: Add missing header dependencies for tc-dwc-g210
We get 2 warnings when build kernel with W=1:
drivers/scsi/ufs/tc-dwc-g210.c:261:5: warning: no previous prototype for 'tc_dwc_g210_config_40_bit' [-Wmissing-prototypes]
drivers/scsi/ufs/tc-dwc-g210.c:293:5: warning: no previous prototype for 'tc_dwc_g210_config_20_bit' [-Wmissing-prototypes]
In fact, these functions are declared in ufs/tc-dwc-g210.h, so this
patch add missing header dependencies
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Baoyou Xie [Sat, 27 Aug 2016 15:49:24 +0000 (23:49 +0800)]
scsi: pmcraid: mark symbols static where possible
We get 4 warnings about global functions without a declaration
in the scsi pmcraid driver when building with W=1:
drivers/scsi/pmcraid.c:309:6: warning: no previous prototype for 'pmcraid_init_cmdblk' [-Wmissing-prototypes]
drivers/scsi/pmcraid.c:404:6: warning: no previous prototype for 'pmcraid_return_cmd' [-Wmissing-prototypes]
drivers/scsi/pmcraid.c:1713:6: warning: no previous prototype for 'pmcraid_ioasc_logger' [-Wmissing-prototypes]
drivers/scsi/pmcraid.c:3141:1: warning: no previous prototype for 'pmcraid_init_ioadls' [-Wmissing-prototypes]
In fact, these functions are only used in the file in which it is
declared and don't need a declaration, but can be made static. so this
patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bryant G. Ly [Wed, 31 Aug 2016 16:29:01 +0000 (11:29 -0500)]
scsi: ibmvscsis: Fixed a bug reported by Dan Carpenter
SUPPORTED_FORMATS is 1 << 1 so it's never zero.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bryant G. Ly [Wed, 31 Aug 2016 16:29:00 +0000 (11:29 -0500)]
scsi: ibmvscsis: Code cleanup of print statements
[mkp: applied by hand]
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently doesn't properly deregisters target sessions
completely, so this will address that.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com> Signed-off-by: Michael Cyr <mikecyr@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:55:36 +0000 (14:55 -0500)]
scsi: smartpqi: bump driver version
[mkp: fixed typo]
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don Brace [Wed, 31 Aug 2016 19:55:30 +0000 (14:55 -0500)]
scsi: smartpqi: add smartpqi.txt
added Documentation/scsi/smartpqi.txt
[mkp: applied by hand]
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Don Brace <don.brace@microsemi.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:55:24 +0000 (14:55 -0500)]
scsi: smartpqi: update Kconfig
The aacraid driver will not managage Microsemi smartpqi controllers, but
will still manage older aacraid devices.
Updated help section.
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:55:17 +0000 (14:55 -0500)]
scsi: smartpqi: remove timeout for cache flush operations
Some cache flush operations can take longer than the timeout value. Best
to not impose a time limit to handle all cases.
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:55:11 +0000 (14:55 -0500)]
scsi: smartpqi: scsi queuecommand cleanup
minor cleanup of scsi queue command function
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:55:05 +0000 (14:55 -0500)]
scsi: smartpqi: minor tweaks to update time support
minor tweaks to update time support
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:54:59 +0000 (14:54 -0500)]
scsi: smartpqi: minor function reformating
reformatted pqi_num_elements_free() to match the rest of the driver
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
the driver no longer waits for the firmware to consume
the event ack IU.
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:54:47 +0000 (14:54 -0500)]
scsi: smartpqi: correct controller offline issue
Fixes: 6c223761e 'smartpqi: initial commit of Microsemi smartpqi driver'
Fixed a bug where the driver would not free all of the
controller resources if the controller ever went offline.
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:54:41 +0000 (14:54 -0500)]
scsi: smartpqi: add kdump support
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:54:35 +0000 (14:54 -0500)]
scsi: smartpqi: enhance reset logic
Eliminated timeout from LUN reset logic.
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:54:23 +0000 (14:54 -0500)]
scsi: smartpqi: simplify spanning
Removed the workaround for the transition to spanning.
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:54:17 +0000 (14:54 -0500)]
scsi: smartpqi: change tmf macro names
small change to make code look cleaner
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kevin Barnett [Wed, 31 Aug 2016 19:54:11 +0000 (14:54 -0500)]
scsi: smartpqi: change aio sg processing
Take advantage of controller improvements.
Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The workqueues "ioc->reset_work_q" and "ioc->fw_event_q" queue a single
work item &ioc->fault_reset_work and &fw_event->work, respectively and
hence don't require ordering. Hence, they have been converted to use
alloc_workqueue().
The WQ_MEM_RECLAIM flag has been set to ensure forward progress under
memory pressure since the workqueue belongs to a storage driver which is
being used on a memory reclaim path.
Since there are fixed number of work items, explicit concurrency limit
is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The workqueue "fc_rescan_work_q" queues multiple work items viz
&ioc->fc_rescan_work, &ioc->fc_lsc_work, &ioc->fc_setup_reset_work,
which require strict execution ordering. Hence, an ordered dedicated
workqueue has been used.
WQ_MEM_RECLAIM has been set since the workqueue is belongs to a storage
driver which is being used on a memory reclaim path and hence, requires
forward progress under memory pressure.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Tue, 30 Aug 2016 16:36:16 +0000 (17:36 +0100)]
scsi: bfa: Do not dereference port before it is null checked
Port is deferenced before it is null sanity checked, hence we
potentially have a null pointer dereference bug. Instead, initialise
trl_enabled from port->fcs->bfa after we are sure port is not null.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Baoyou Xie [Mon, 29 Aug 2016 10:46:51 +0000 (18:46 +0800)]
scsi: qla4xxx: Mark symbols static where possible
We get 1 warning when build kernel with W=1:
drivers/scsi/qla4xxx/ql4_nx.c:1846:10: warning: no previous prototype for 'ql4_84xx_ipmdio_rd_reg' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static. This patch marks
this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Acked-by: Nilesh Javali <nilesh.javali@qlogic.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Baoyou Xie [Tue, 30 Aug 2016 11:26:00 +0000 (19:26 +0800)]
scsi: move function declarations to scsi_priv.h
We get 2 warnings about global functions without a declaration in the
scsi driver when building with W=1:
drivers/scsi/scsi_lib.c:467:6: warning: no previous prototype for 'scsi_requeue_run_queue' [-Wmissing-prototypes]
drivers/scsi/scsi_lib.c:2609:6: warning: no previous prototype for 'scsi_evt_thread' [-Wmissing-prototypes]
In fact, both functions are declared in drivers/scsi/scsi_scan.c but
need to move them into scsi_priv.h.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistakes in ql_dbg messages.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
projects / karo-tx-linux.git / log