Alan Stern [Tue, 17 May 2011 18:45:48 +0000 (14:45 -0400)]
usb-storage: fix up the unusual_realtek device list
This patch (as1461) fixes the unusual_devs entries for the Realtek USB
card reader. They should be ordered by PID, and they should not
override the Subclass and Protocol values provided by the device.
Otherwise a notification about unnecessary entries gets printed in the
kernel log during probing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-By: Tony Vroon <tony@linx.net> CC: <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 17 May 2011 14:40:51 +0000 (10:40 -0400)]
EHCI: don't rescan interrupt QHs needlessly
This patch (as1466) speeds up processing of ehci-hcd's periodic list.
The existing code will pointlessly rescan an interrupt endpoint queue
each time it encounters the queue's QH in the periodic list, which can
happen quite a few times if the endpoint's period is low. On some
embedded systems, this useless overhead can waste so much time that
the driver falls hopelessly behind and loses events.
The patch introduces a "periodic_stamp" variable, which gets
incremented each time scan_periodic() runs and each time the scan
advances to a new frame. If the corresponding stamp in an interrupt
QH is equal to the current periodic_stamp, we assume the QH has
already been scanned and skip over it. Otherwise we scan the QH as
usual, and if none of its URBs have completed then we store the
current periodic_stamp in the QH's stamp, preventing it from being
scanned again.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original problem encountered by people using NVIDIA chipsets was
that USB devices were not turning off when the system shut down. For
example, the LED on an optical mouse would remain on, draining a
laptop's battery. The problem was caused by a bug in the chipset; an
OHCI controller in the Reset state would continue to drive a bus reset
signal even after system shutdown. The workaround was to put the
controllers into the Suspend state instead.
It turns out that later NVIDIA chipsets do not suffer from this bug.
Instead some have the opposite bug: If a system is shut down while an
OHCI controller is in the Suspend state, USB devices remain powered!
On other systems, shutting down with a Suspended controller causes the
system to reboot immediately. Thus, working around the original bug
on some machines exposes other bugs on other machines.
The best solution seems to be to limit the workaround to OHCI
controllers with a low-numbered PCI product ID. I don't know exactly
at what point NVIDIA changed their chipsets; the value used here is a
guess. So far it was worked out okay for all the people who have
tested it.
This fixes Bugzilla #35032.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com> Tested-by: Yury Siamashka <yurand2@gmail.com> CC: <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark Brown [Sun, 15 May 2011 16:55:58 +0000 (09:55 -0700)]
USB: OTG: msm: Free VCCCX regulator even if we can't set the voltage
If for some reason we fail to set the voltage range for the VDDCX regulator
when removing it's better to still disable and free the regulator as that
avoids leaking a reference to it and is likely to ensure that it's turned
off completely.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Mark Brown [Sun, 15 May 2011 16:55:57 +0000 (09:55 -0700)]
USB: OTG: msm: Allow the widest possible range for VDDCX when removing
When not active the hardware should be able to tolerate voltages within
the normal operating range so when removing set the maximum voltage we
can use to the maximum rather than minimum of the operating range. This
will improve interoperability in case we end up sharing the supply in
some design.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I am sharing patch to the devices/usb/serial/option.c. This allows
operation of Huawei E353 broadband modem using the “option” driver. The
patch simply adds new constant with proper product ID and an entry to
usb_device_id. I worked on the 2.6.38.6 sources. Tested on Dell inspiron
1764 (i3 core cpu) and brand new Huawei E353 modem, Fedora 15 beta.
Looking at the type of change, i doubt it has potential to introduce
problems in other parts of kernel or the driver itself.
Sarah Sharp [Fri, 13 May 2011 01:06:37 +0000 (18:06 -0700)]
xhci: Fix memory leak bug when dropping endpoints
When the USB core wants to change to an alternate interface setting that
doesn't include an active endpoint, or de-configuring the device, the xHCI
driver needs to issue a Configure Endpoint command to tell the host to
drop some endpoints from the schedule. After the command completes, the
xHCI driver needs to free rings for any endpoints that were dropped.
Unfortunately, the xHCI driver wasn't actually freeing the endpoint rings
for dropped endpoints. The rings would be freed if the endpoint's
information was simply changed (and a new ring was installed), but dropped
endpoints never had their rings freed. This caused errors when the ring
segment DMA pool was freed when the xHCI driver was unloaded:
[ 5582.883995] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff88003371d000 busy
[ 5582.884002] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033716000 busy
[ 5582.884011] xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880033455000 busy
[ 5582.884018] xhci_hcd 0000:06:00.0: Freed segment pool
[ 5582.884026] xhci_hcd 0000:06:00.0: Freed device context pool
[ 5582.884033] xhci_hcd 0000:06:00.0: Freed small stream array pool
[ 5582.884038] xhci_hcd 0000:06:00.0: Freed medium stream array pool
[ 5582.884048] xhci_hcd 0000:06:00.0: xhci_stop completed - status = 1
[ 5582.884061] xhci_hcd 0000:06:00.0: USB bus 3 deregistered
[ 5582.884193] xhci_hcd 0000:06:00.0: PCI INT A disabled
Fix this issue and free endpoint rings when their endpoints are
successfully dropped.
This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@kernel.org
Sarah Sharp [Mon, 16 May 2011 20:09:08 +0000 (13:09 -0700)]
xhci: Fix memory leak in ring cache deallocation.
When an endpoint ring is freed, it is either cached in a per-device ring
cache, or simply freed if the ring cache is full. If the ring was added
to the cache, then virt_dev->num_rings_cached is incremented. The cache
is designed to hold up to 31 endpoint rings, in array indexes 0 to 30.
When the device is freed (when the slot was disabled),
xhci_free_virt_device() is called, it would free the cached rings in
array indexes 0 to virt_dev->num_rings_cached.
Unfortunately, the original code in xhci_free_or_cache_endpoint_ring()
would put the first entry into the ring cache in array index 1, instead of
array index 0. This was caused by the second assignment to rings_cached:
This meant that when the device was freed, cached rings with indexes 0 to
N would be freed, and the last cached ring in index N+1 would not be
freed. When the driver was unloaded, this caused interesting messages
like:
xhci_hcd 0000:06:00.0: dma_pool_destroy xHCI ring segments, ffff880063040000 busy
This should be queued to stable kernels back to 2.6.33.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable@kernel.org
introduced a bug. The USB 2.0 spec says that full speed isochronous endpoints'
bInterval must be decoded as an exponent to a power of two (e.g. interval =
2^(bInterval - 1)). Full speed interrupt endpoints, on the other hand, don't
use exponents, and the interval in frames is encoded straight into bInterval.
Dmitry's patch was supposed to fix up the full speed isochronous to parse
bInterval as an exponent, but instead it changed the *interrupt* endpoint
bInterval decoding. The isochronous endpoint encoding was the same.
This caused full speed devices with interrupt endpoints (including mice, hubs,
and USB to ethernet devices) to fail under NEC 0.96 xHCI host controllers:
[ 100.909818] xhci_hcd 0000:06:00.0: add ep 0x83, slot id 1, new drop flags = 0x0, new add flags = 0x99, new slot info = 0x38100000
[ 100.909821] xhci_hcd 0000:06:00.0: xhci_check_bandwidth called for udev ffff88011f0ea000
...
[ 100.910187] xhci_hcd 0000:06:00.0: ERROR: unexpected command completion code 0x11.
[ 100.910190] xhci_hcd 0000:06:00.0: xhci_reset_bandwidth called for udev ffff88011f0ea000
When the interrupt endpoint was added and a Configure Endpoint command was
issued to the host, the host controller would return a very odd error message
(0x11 means "Slot Not Enabled", which isn't true because the slot was enabled).
Probably the host controller was getting very confused with the bad encoding.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Dmitry Torokhov <dtor@vmware.com> Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com> Tested-by: Thomas Lindroth <thomas.lindroth@gmail.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Merge branch 'for-next' of master.kernel.org:/pub/scm/linux/kernel/git/balbi/usb into usb-next
* 'for-next' of master.kernel.org:/pub/scm/linux/kernel/git/balbi/usb:
MAINTAINERS: tree moved to kernel.org
usb: musb: Calling VBUS pulsing API when SRP is initiated.
usb: otg: TWL6030: OMAP4430: Adding SRP VBUS pulsing API
usb: musb: host: remove duplicate check in musb_ep_program()
usb: musb: export musb_interrupt symbol
usb: musb: allow musb and glue layers to be modules
usb: musb: drop unneeded musb_debug trickery
Felipe Balbi [Fri, 13 May 2011 13:53:48 +0000 (16:53 +0300)]
usb: gadget: rndis: don't test against req->length
composite.c always sets req->length to zero
and expects function driver's setup handlers
to return the amount of bytes to be used
on req->length. If we test against req->length
w_length will always be greater than req->length
thus making us always stall that particular
SEND_ENCAPSULATED_COMMAND request.
Julia Lawall [Fri, 13 May 2011 15:30:46 +0000 (17:30 +0200)]
drivers/usb/serial/opticon.c: Release resources on kmalloc failure
Several resources have been allocated before this kmalloc failure, and thus
they should be released in this error handling code, as done in nearby
error handling code.
The semantic match that finds this problem is:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression urb;
statement S;
position p1,p2;
@@
urb = usb_alloc_urb@p1(...);
... when != urb
if (urb == NULL) S
... when != urb
(
return <+...urb...+>;
|
return@p2 ...;
)
Hema HK [Tue, 22 Mar 2011 11:24:21 +0000 (16:54 +0530)]
usb: otg: TWL6030: OMAP4430: Adding SRP VBUS pulsing API
Implement the start_srp API to generate the VBUS pulsing and assign it to
otg_transciever function pointer. This will be used by the link driver when
there is SRP initiation from user.
Signed-off-by: Hema HK <hemahk@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Sergei Shtylyov [Sat, 7 May 2011 15:44:13 +0000 (19:44 +0400)]
usb: musb: host: remove duplicate check in musb_ep_program()
musb_ep_program() contains obviously duplicate check for 'dma_channel' in its
IN/receive path -- removing it allows to save one level of indentation. While
at it, improve the comment style...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe Balbi [Wed, 11 May 2011 10:02:23 +0000 (13:02 +0300)]
usb: musb: export musb_interrupt symbol
currently that's used by another module
(am35x) which, granted, it shouldn't be
using that, but in order to avoid compile
errors, let's export that symbol temporarily
until re-factoring work is done on that
driver.
Felipe Balbi [Wed, 11 May 2011 09:47:59 +0000 (12:47 +0300)]
usb: musb: allow musb and glue layers to be modules
This in part reverts commit 7a180e70cfc56e131bfe4796773df2acfc7d4180.
(usb: musb: temporarily make it bool) and while
at that we also allow glue layers to be compiled
as modules.
There are still some other changes needed
until we can have a fully functional build
with this setup, but we're getting there.
Felipe Balbi [Wed, 11 May 2011 09:44:08 +0000 (12:44 +0300)]
usb: musb: drop unneeded musb_debug trickery
We have a generic way of enabling/disabling
different debug messages on a driver called
DYNAMIC_PRINTK. Anyone interested in enabling
just part of the debug messages, please read
the documentation under:
Documentation/dynamic-debug-howto.txt
for information on how to use that great
infrastructure.
huajun li [Tue, 3 May 2011 13:11:00 +0000 (21:11 +0800)]
xhci: move the common code to a function to get max ports and port array
There are several functions using same code to get max ports and port array,
this patch moves the common code to a function in order to reuse them easily.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Andy Ross [Wed, 11 May 2011 22:52:38 +0000 (15:52 -0700)]
ehci: workaround for pci quirk timeout on ExoPC
The BIOS handoff for the unused EHCI controller on the ExoPC tablet
hangs for 90 seconds on boot. Detect that device, skip negotiation
and force the handoff.
Signed-off-by: Andy Ross <andy.ross@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Fri, 6 May 2011 02:08:09 +0000 (19:08 -0700)]
xhci: Fix bug in control transfer cancellation.
When the xHCI driver attempts to cancel a transfer, it issues a Stop
Endpoint command and waits for the host controller to indicate which TRB
it was in the middle of processing. The host will put an event TRB with
completion code COMP_STOP on the event ring if it stops on a control
transfer TRB (or other types of transfer TRBs). The ring handling code
is supposed to set ep->stopped_trb to the TRB that the host stopped on
when this happens.
Unfortunately, there is a long-standing bug in the control transfer
completion code. It doesn't actually check to see if COMP_STOP is set
before attempting to process the transfer based on which part of the
control TD completed. So when we get an event on the data phase of the
control TRB with COMP_STOP set, it thinks it's a normal completion of
the transfer and doesn't set ep->stopped_td or ep->stopped_trb.
When the ring handling code goes on to process the completion of the Stop
Endpoint command, it sees that ep->stopped_trb is not a part of the TD
it's trying to cancel. It thinks the hardware has its enqueue pointer
somewhere further up in the ring, and thinks it's safe to turn the control
TRBs into no-op TRBs. Since the hardware was in the middle of the control
TRBs to be cancelled, the proper software behavior is to issue a Set TR
dequeue pointer command.
It turns out that the NEC host controllers can handle active TRBs being
set to no-op TRBs after a stop endpoint command, but other host
controllers have issues with this out-of-spec software behavior. Fix this
behavior.
This patch should be backported to kernels as far back as 2.6.31, but it
may be a bit challenging, since process_ctrl_td() was introduced in some
refactoring done in 2.6.36, and some endian-safe patches added in 2.6.40
that touch the same lines.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: stable@kernel.org
Erik Slagter [Wed, 11 May 2011 10:06:55 +0000 (12:06 +0200)]
USB: cdc_acm: Fix oops when Droids MuIn LCD is connected
The Droids MuIn LCD operates like a serial remote terminal.
Data received are displayed directly on the LCD. This patch
fixes the kernel null pointer oops when it is plugged in.
Add NO_DATA_INTERFACE quirk to tell the driver that "control"
and "data" interfaces are not separated for this device, which
prevents dereferencing a null pointer in the device probe code.
Signed-off-by: Erik Slagter <erik@slagter.name> Signed-off-by: Maxin B. John <maxin.john@gmail.com> Tested-by: Erik Slagter <erik@slagter.name> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Abraham [Sat, 7 May 2011 20:28:04 +0000 (22:28 +0200)]
USB: Gadget: Add Samsung S3C24XX USB High-Speed controller driver
The Samsung's S3C2416, S3C2443 and S3C2450 includes a USB High-Speed
device controller module. This driver enables support for USB high-speed
gadget functionality for the Samsung S3C24xx SoC's that include this
controller.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Signed-off-by: Sangbeom Kim <sbkim73@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Alexander Neumann <alexander@bumpern.de> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Abraham [Sat, 7 May 2011 20:29:16 +0000 (22:29 +0200)]
ARM: S3C2416: Add support for USB 2.0 High-Speed gadget controller
Add support for USB 2.0 High-Speed gadget controller driver for Samsung's
S3C2416 processor.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Signed-off-by: Sangbeom Kim <sbkim73@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Abraham [Sat, 7 May 2011 20:26:53 +0000 (22:26 +0200)]
ARM: S3C24XX: Add plaform device definition for USB High-Speed gadget controller.
S3C2416, S3C2443 and S3C2450 includes a USB High-Speed Gadget controller module.
This patch adds the following for supporting this controller.
1. Definition for USB High-Speed controller base address.
2. Platform device instantiation.
3. Declaration for platform data structure.
4. Functionality to setup platform data for the controller.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Signed-off-by: Sangbeom Kim <sbkim73@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Abraham [Sat, 7 May 2011 20:24:49 +0000 (22:24 +0200)]
ARM: S3C2416: Add USB Phy register definitions
Add register definitions required to configure the USB Phy. The definitions
for PHYCTRL, PHYPWR, URSTCON and UCLKCON registers and corresponding bit
field definitions are added.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Signed-off-by: Sangbeom Kim <sbkim73@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Maxin B John [Sun, 8 May 2011 12:56:17 +0000 (15:56 +0300)]
usb: gadget: Remove the LUN checks which are always true
Comparing an unsigned integer with greater than or equal to zero is
always true. So, it is safe to remove similar checks from
'f_mass_storage.c' and 'file_storage.c'
Signed-off-by: Maxin B. John <maxin.john@gmail.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jingoo Han [Mon, 9 May 2011 06:28:39 +0000 (15:28 +0900)]
USB: ehci-s5p : use __devinit and __devexit macros for probe and remove
The __devinit and __devexit macros were added to probe and remove
functions. The macros move the probe and remove functions to the
devinit and devexit sections
Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roger Quadros [Mon, 9 May 2011 10:08:07 +0000 (13:08 +0300)]
usb: gadget: f_mass_storage: Make us pass USBCV MSC Compliance tests
Defer the SET_CONFIG and SET_INTERFACE control transfer's data/status
stages till we are ready to process new CBW from the host. This way we
ensure that we don't loose any CBW during MSC compliance tests and cause
lock up.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com> Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roger Quadros [Mon, 9 May 2011 10:08:06 +0000 (13:08 +0300)]
usb: gadget: composite: Allow function drivers to pause control transfers
Some USB function drivers (e.g. f_mass_storage.c) need to delay or defer the
data/status stages of standard control requests like SET_CONFIGURATION or
SET_INTERFACE till they are done with their bookkeeping and are actually ready
for accepting new commands to their interface.
They can now achieve this functionality by returning USB_GADGET_DELAYED_STATUS
in their setup handlers (e.g. set_alt()). The composite framework will then
defer completion of the control transfer by not completing the data/status stages.
This ensures that the host does not send new packets to the interface till the
function driver is ready to take them.
When the function driver that requested for USB_GADGET_DELAYED_STATUS is done
with its bookkeeping, it should signal the composite framework to continue with
the data/status stages of the control transfer. It can do so by invoking
the new API usb_composite_setup_continue(). This is where the control transfer's
data/status stages are completed and host can initiate new transfers.
The DELAYED_STATUS mechanism is currently only supported if the expected data phase
is 0 bytes (i.e. w_length == 0). Since SET_CONFIGURATION and SET_INTERFACE are the
only cases that will use this mechanism, this is not a limitation.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Merge branch 'for-usb-next' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
* 'for-usb-next' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
xHCI 1.0: Max Exit Latency Too Large Error
xHCI 1.0: TT_THINK_TIME set
xHCI 1.0: Block Interrupts for Isoch transfer
xHCI 1.0: Isoch endpoint CErr field set
xHCI 1.0: Control endpoint average TRB length field set
xHCI 1.0: Setup Stage TRB Transfer Type flag
Hugh Dickins [Tue, 10 May 2011 00:44:42 +0000 (17:44 -0700)]
vm: fix vm_pgoff wrap in upward expansion
Commit a626ca6a6564 ("vm: fix vm_pgoff wrap in stack expansion") fixed
the case of an expanding mapping causing vm_pgoff wrapping when you had
downward stack expansion. But there was another case where IA64 and
PA-RISC expand mappings: upward expansion.
Linus Torvalds [Mon, 9 May 2011 23:59:51 +0000 (16:59 -0700)]
Merge branch 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915/lvds: Only act on lid notify when the device is on
drm/i915: fix intel_crtc_clock_get pipe reads after "cleanup cleanup"
drm/i915: Only enable the plane after setting the fb base (pre-ILK)
drm/i915/dp: Be paranoid in case we disable a DP before it is attached
drm/i915: Release object along create user fb error path
Mikulas Patocka [Mon, 9 May 2011 11:01:09 +0000 (13:01 +0200)]
Don't lock guardpage if the stack is growing up
Linux kernel excludes guard page when performing mlock on a VMA with
down-growing stack. However, some architectures have up-growing stack
and locking the guard page should be excluded in this case too.
This patch fixes lvm2 on PA-RISC (and possibly other architectures with
up-growing stack). lvm2 calculates number of used pages when locking and
when unlocking and reports an internal error if the numbers mismatch.
[ Patch changed fairly extensively to also fix /proc/<pid>/maps for the
grows-up case, and to move things around a bit to clean it all up and
share the infrstructure with the /proc bits.
Tested on ia64 that has both grow-up and grow-down segments - Linus ]
Linus Torvalds [Mon, 9 May 2011 19:00:49 +0000 (12:00 -0700)]
Merge branch 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
eeepc-laptop: Use ACPI handle to identify rfkill port
[PATCH] sony-laptop: limit brightness range to DSDT provided ones
sony-laptop: report failures on setting LCD brightness
thinkpad-acpi: module autoloading for newer Lenovo ThinkPads.
Alex He [Thu, 5 May 2011 10:14:12 +0000 (18:14 +0800)]
xHCI 1.0: Max Exit Latency Too Large Error
This is a new TRB Completion Code of the xHCI spec 1.0.
Asserted by the Evalute Context Command if the proposed Max Exit Latency would
not allow the periodic endpoints of the Device Slot to be scheduled.
Signed-off-by: Alex He <alex.he@amd.com> Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Andiry Xu [Thu, 5 May 2011 10:14:02 +0000 (18:14 +0800)]
xHCI 1.0: Block Interrupts for Isoch transfer
Currently an isoc URB is divided into multiple TDs, and every TD will
trigger an interrupt when it's processed. However, software can schedule
multiple TDs at a time, and it only needs an interrupt every URB.
xHCI 1.0 introduces the Block Event Interrupt(BEI) flag which allows Normal
and Isoch Transfer TRBs to place an Event TRB on an Event Ring but not
assert an intrrupt to the host, and the interrupt rate is significantly
reduced and the system performance is improved.
Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Andiry Xu [Thu, 5 May 2011 10:13:56 +0000 (18:13 +0800)]
xHCI 1.0: Setup Stage TRB Transfer Type flag
Setup Stage Transfer Type field is added to indicate the presence and the
direction of the Data Stage TD, and determines the direction of the Status
Stage TD so the wLength length field should be ignored by the xHC.
Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Alex Williamson [Thu, 21 Apr 2011 22:08:14 +0000 (16:08 -0600)]
drm/i915/lvds: Only act on lid notify when the device is on
If we're using vga switcheroo, the device may be turned off
and poking it can return random state. This provokes an OOPS fixed
separately by 8ff887c847 (drm/i915/dp: Be paranoid in case we disable a
DP before it is attached). Trying to use and respond to events on a
device that has been turned off by the user is in principle a silly thing
to do.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: stable@kernel.org Signed-off-by: Keith Packard <keithp@keithp.com>
Chris Wilson [Fri, 22 Apr 2011 21:17:21 +0000 (22:17 +0100)]
drm/i915: fix intel_crtc_clock_get pipe reads after "cleanup cleanup"
Despite the fixes in 548f245ba6a31 (drm/i915: fix per-pipe reads after
"cleanup"), we missed one neighbouring read that was mistakenly replaced
with the reg value in 9db4a9c (drm/i915: cleanup per-pipe reg usage).
This was preventing us from correctly determining the mode the BIOS left
the panel in for machines that neither have an OpRegion nor access to
the VBT, (e.g. the EeePC 700).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: stable@kernel.org Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Keith Packard <keithp@keithp.com>
Chris Wilson [Tue, 19 Apr 2011 20:14:14 +0000 (21:14 +0100)]
drm/i915: Only enable the plane after setting the fb base (pre-ILK)
When enabling the plane, it is helpful to have already pointed that
plane to valid memory or else we may incur the wrath of a PGTBL_ER.
This code preserved the behaviour from the bad old days for unknown
reasons...
Found by assert_fb_bound_for_plane().
References: https://bugs.freedesktop.org/show_bug.cgi?id=36246 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Keith Packard <keithp@keithp.com>
Linus Torvalds [Mon, 9 May 2011 16:09:04 +0000 (09:09 -0700)]
Merge branch 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add pci id to acer travelmate quirk for 5730
drm/radeon: fix order of doing things in radeon_crtc_cursor_set
drm: mm: fix debug output
drm/radeon/kms: ATPX switcheroo fixes
drm/nouveau: Fix a crash at card takedown for NV40 and older cards
Linus Torvalds [Mon, 9 May 2011 16:07:55 +0000 (09:07 -0700)]
Merge branch 'hpfs'
* hpfs:
HPFS: Remove unused variable
HPFS: Move declaration up, so that there are no out-of-scope pointers
HPFS: Fix some unaligned accesses
HPFS: Fix endianity. Make hpfs work on big-endian machines
HPFS: Implement fsync for hpfs
HPFS: Fix a bug that filesystem was not marked dirty when remounting it
HPFS: Restrict uid and gid to 16-bit values
HPFS: When marking or clearing the dirty bit, sync the filesystem
HPFS: Use types with defined width
HPFS: Remove mark_inode_dirty
HPFS: Remove CR/LF conversion option
HPFS: Remove remaining locks
HPFS: Introduce a global mutex and lock it on every callback from VFS.
HPFS: Make HPFS compile on preempt and SMP
Matthew Garrett [Mon, 9 May 2011 14:44:01 +0000 (10:44 -0400)]
eeepc-laptop: Use ACPI handle to identify rfkill port
The ACPI notification we get from rfkill events on these machines gives
us all the information we need to identify the port that's changed. Do
so rather than assuming that it's always bus 1.
Mattia Dongili [Mon, 9 May 2011 14:20:29 +0000 (10:20 -0400)]
[PATCH] sony-laptop: limit brightness range to DSDT provided ones
The new style brightness control provides an operating range of 9 values
(seems consistent over a large number of models sharing the same
brightness control methods).
Read and use the minimum and maximum values to limit the backlight
interface between those boundaries.
Signed-off-by: Mattia Dongili <malattia@linux.it> Signed-off-by: Matthew Garrett <mjg@redhat.com>
Manoj Iyer [Sun, 8 May 2011 22:04:29 +0000 (18:04 -0400)]
thinkpad-acpi: module autoloading for newer Lenovo ThinkPads.
The newer Lenovo ThinkPads have HKEY HID of LEN0068 instead
of IBM0068. Added new HID so that thinkpad_acpi module will
auto load on these newer Lenovo ThinkPads.
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Cc: stable@kernel.org Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com> Signed-off-by: Andy Lutomirski <luto@mit.edu> Signed-off-by: Matthew Garrett <mjg@redhat.com>
Ilija Hadzic [Thu, 5 May 2011 00:15:03 +0000 (20:15 -0400)]
drm/radeon: fix order of doing things in radeon_crtc_cursor_set
if object pin or object lookup in radeon_cursor_set fail, the function
could leave inconsistent mouse width and hight values in radeon_crtc
fixed by moving cursor width and height assignments after all
checks have passed
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com> Reviewed-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
Jimmy Rentz [Sun, 17 Apr 2011 20:15:09 +0000 (16:15 -0400)]
drm/nouveau: Fix a crash at card takedown for NV40 and older cards
NV40 and older cards (pre NV50) reserve a vram bo for the vga memory at
card init. This bo is then freed at card shutdown. The problem is that
the ttm bo vram manager was already freed. So a crash occurs when the
vga bo is freed. The fix is to free the vga bo prior to freeing the ttm
bo vram manager. There might be other solutions but this seemed the
simplest to me.
Signed-off-by: Jimmy Rentz <jb17bsome@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Implement good battery algorithm defined in the battery charging V1.2 spec
for detecting different charging ports. USB hardware is put into low power
mode when connected to a dedicated charging port. vbus_draw and set_power
methods are implemented for determining the allowed current from Host in
different states (un-configured/suspend/configured).
The charger block is implemented using vendor specific registers and the
PHY used in MSM8960(28nm PHY) different from older targets like MSM8x60
and MSM7x30(45nm PHY). The PHY vendor and product id registers are not
implemented in the above chipsets. Hence PHY type is passed via platform
data.
Anji jonnala [Wed, 4 May 2011 04:49:46 +0000 (10:19 +0530)]
USB: OTG: msm: vote for dayatona fabric clock
HSUSB core clock is derived from daytona fabric clock and for
HSUSB operational require minimum core clock at 55MHz. Since, HSUSB
cannot tolerate daytona fabric clock change in the middle of HSUSB
operational, vote for maximum Daytona fabric clock
while usb is operational
Jan Andersson [Fri, 6 May 2011 10:00:18 +0000 (12:00 +0200)]
USB: UHCI: Add support for GRLIB GRUSBHC controller
This patch adds support for the UHCI part of the GRLIB GRUSBHC controller
found on some LEON/GRLIB SoCs.
The UHCI HCD previously only supported controllers connected over PCI.
This patch adds support for the first non-PCI UHCI HC. I have tried to
replicate the solution used in ehci-hcd.c.
Tested on GR-LEON4-ITX board (LEON4/GRLIB with GRUSBHC) and x86 with Intel
UHCI HC.
Signed-off-by: Jan Andersson <jan@gaisler.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan Andersson [Fri, 6 May 2011 10:00:17 +0000 (12:00 +0200)]
USB: UHCI: Support non-PCI host controllers
This patch is part of a series that extend the UHCI HCD to support
non-PCI host controllers.
This patch also extends the uhci_{read,write}* functions to allow accesses
to registers not mapped into PCI I/O space. This extension also includes
the addition of a void __iomem pointer to the uhci structure.
A new Kconfig option is added to signal that the system has a non-PCI HC.
If this Kconfig option is set, uhci-hcd.c will include generic reset functions
for systems that do not make use of keyboard and mouse legacy support. PCI
controllers will still always use the reset functions from pci-quirks
This patch is followed by a patch that adds bus glue for the first non-PCI
UHCI HC.
Signed-off-by: Jan Andersson <jan@gaisler.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan Andersson [Fri, 6 May 2011 10:00:16 +0000 (12:00 +0200)]
USB: UHCI: Wrap I/O register accesses
This patch is part of a series that extend the UHCI HCD to support
non-PCI controllers.
This patch replaces in{b,w,l} and out{b,wl} with calls to local inline
functions. This is done so that the register access functions can be
extended to support register areas not mapped in PCI I/O space.
Signed-off-by: Jan Andersson <jan@gaisler.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan Andersson [Fri, 6 May 2011 10:00:14 +0000 (12:00 +0200)]
USB: UHCI: Codingstyle fixes
This patch is part of a series that extend the UHCI HCD to support
non-PCI host controllers.
This patch fixes the following warnings from checkpatch:
ERROR: switch and case should be at the same indent
+ switch (to_pci_dev(uhci_dev(uhci))->vendor) {
+ default:
[...]
+ case PCI_VENDOR_ID_GENESYS:
[...]
+ case PCI_VENDOR_ID_INTEL:
WARNING: static char array declaration should probably be static const char
+ static char bad_Asus_board[] = "A7V8X";
WARNING: Use DEFINE_PCI_DEVICE_TABLE for struct pci_device_id
+static const struct pci_device_id uhci_pci_ids[] = { {
Signed-off-by: Jan Andersson <jan@gaisler.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan Andersson [Fri, 6 May 2011 10:00:13 +0000 (12:00 +0200)]
USB: UHCI: Allow dynamic assignment of bus specific functions
This patch is part of a series that extend the UHCI HCD to support
non-PCI controllers.
This patch changes calls to uhci_reset_hc, uhci_check_and_reset_hc,
configure_hc, resume_detect_interrupts_are_broken and
global_suspend_mode_is_broken so that they are made through pointers
in the uhci hcd struct. This will allow these functions to be replaced
with bus/arch specific functions.
Signed-off-by: Jan Andersson <jan@gaisler.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jan Andersson [Fri, 6 May 2011 10:00:12 +0000 (12:00 +0200)]
USB: UHCI: Remove PCI dependencies from uhci-hub
This patch is part of a series that extend the UHCI HCD to support
non-PCI host controllers.
uhci-hub.c contained two PCI vendor checks for silicon quirks. Move
these checks into uhci-hcd.c and use bits in uhci_hcd structure to
mark that we need to use the quirks.
This patch is followed by other patches that will remove PCI
dependencies from uhci-hcd.c as well.
Signed-off-by: Jan Andersson <jan@gaisler.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ramneek Mehresh [Wed, 4 May 2011 14:11:55 +0000 (19:41 +0530)]
fsl/usb: Unused endpoint failure for USB gadget
Though USB controller works without this most of the time, an issue was faced
where USB was configured as printer device and it was dropping first
packet(64 bytes) in full speed mode due to DATA PID mismatch.
The problem gets resolved once unused endpoints are configured as bulk.
As per P1020 RM (Table17-31, bits 19-18, bits 3-2) "When only one endpoint
(RX or TX, but not both) of an endpoint pair is used, the unused endpoint
should be configured as a bulk type endpoint." So according to the RM,
this patch is initializing TX and RX endpoints as bulk type
projects / karo-tx-linux.git / log