Tom Herbert [Fri, 7 Nov 2014 02:06:01 +0000 (18:06 -0800)]
vxlan: Fix to enable UDP checksums on interface
Add definition to vxlan nla_policy for UDP checksum. This is necessary
to enable UDP checksums on VXLAN.
In some instances, enabling UDP checksums can improve performance on
receive for devices that return legacy checksum-unnecessary for UDP/IP.
Also, UDP checksum provides some protection against VNI corruption.
Testing:
Ran 200 instances of TCP_STREAM and TCP_RR on bnx2x.
TCP_STREAM
IPv4, without UDP checksums
14.41% TX CPU utilization
25.71% RX CPU utilization
9083.4 Mbps
IPv4, with UDP checksums
13.99% TX CPU utilization
13.40% RX CPU utilization
9095.65 Mbps
TCP_RR
IPv4, without UDP checksums
94.08% TX CPU utilization
156/248/462 90/95/99% latencies
1.12743e+06 tps
IPv4, with UDP checksums
94.43% TX CPU utilization
158/250/462 90/95/99% latencies
1.13345e+06 tps
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following series of patches fixes a couple of bugs that slipped
through my last series.
- Free channel structure after freeing the per channel interrupts
- If an skb error allocation occurs during receive processing check
whether more descriptors are associated with the packet or whether
to start on a new packet
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
amd-xgbe: Check for complete packet on skb allocation error
If the skb allocation fails during receive processing, the driver would
continue reading descriptors without first determining if there were
any more descriptors for the current packet. Update the code to check
whether more descriptors are associated with the current packet or
whether to move on to the next descriptor as a new packet.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The channel structure is freed before freeing the per channel
interrupts resulting in a kernel oops. Move the call to free
the channel structure to after the freeing of the per channel
interrupts.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
fixes: a03bb56e67c357980dae886683733dab5583dc14 ("enic: implement rx_copybreak") Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
enic: handle error condition properly in enic_rq_indicate_buf
In case of error in rx path, we free the buf->os_buf but we do not make it NULL.
In next iteration we use the skb which is already freed. This causes the
following crash.
fixes: a03bb56e67c357980dae886683733dab5583dc14 ("enic: implement rx_copybreak") Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Thu, 6 Nov 2014 10:51:22 +0000 (12:51 +0200)]
net/mlx5_core: Fix race on driver load
When events arrive at driver load, the event handler gets called even before
the spinlock and list are initialized. Fix this by moving the initialization
before EQs creation.
Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Thu, 6 Nov 2014 10:51:21 +0000 (12:51 +0200)]
net/mlx5_core: Fix race in create EQ
After the EQ is created, it can possibly generate interrupts and the interrupt
handler is referencing eq->dev. It is therefore required to set eq->dev before
calling request_irq() so if an event is generated before request_irq() returns,
we will have a valid eq->dev field.
Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 6 Nov 2014 20:16:44 +0000 (15:16 -0500)]
Merge branch 'sunvnet-next'
Sowmini Varadhan says:
====================
sunvnet: bug fixes
This patch series has a coding-style fix and a bug fix.
The coding style fix (patch 1) is the extra indentation flagged by
Ben Hutchings:
http://marc.info/?l=linux-netdev&m=141529243409594&w=2
The bugfix (patch 2) is the following:
when vnet_event_napi() is called as part of napi_resume
(i.e., continuation of a previous NAPI read that was truncated
due to budget constraints), and then finds no more packets to read,
the code was trying to avoid an additional trip through ldc_rx
as an optimization. However, when this corner case happens, we would
need to reset a number of dring state bits such as rcv_nxt carefully,
which quickly becomes complex and hacky. The cleaner solution
is to just roll back to vnet_poll, re-enable interrupts and set up
dring state as was done in the pre-NAPI version of the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
sunvnet: Return from vnet_napi_event() if no packets to read
vnet_event_napi() may be called as part of the NAPI ->poll,
to resume reading descriptor rings. When no data is available,
descriptor ring state (e.g., rcv_nxt) needs to be reset
carefully to stay in lock-step with ldc_read(). In the interest
of simplicity, the best way to do this is to return from
vnet_event_napi() when there are no more packets to read.
The next trip through ldc_rx will correctly set up the dring state.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Tested-by: David Stevens <david.stevens@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 5 Nov 2014 18:47:28 +0000 (19:47 +0100)]
net: dsa: slave: Fix autoneg for phys on switch MDIO bus
When the ports phys are connected to the switches internal MDIO bus,
we need to connect the phy to the slave netdev, otherwise
auto-negotiation etc, does not work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Wed, 5 Nov 2014 19:51:51 +0000 (20:51 +0100)]
sched: fix act file names in header comment
Fixes: 4bba3925 ("[PKT_SCHED]: Prefix tc actions with act_") Signed-off-by: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N [Wed, 5 Nov 2014 13:03:31 +0000 (18:33 +0530)]
drivers: net: cpsw: remove cpsw_ale_stop from cpsw_ale_destroy
when cpsw is build as modulea and simple insert and removal of module
creates a deadlock, due to delete timer. the timer is created and destroyed
in cpsw_ale_start and cpsw_ale_stop which are from device open and close.
root@am437x-evm:~# modprobe -r ti_cpsw
[ 158.505333] INFO: trying to register non-static key.
[ 158.510623] the code is fine but needs lockdep annotation.
[ 158.516448] turning off the locking correctness validator.
[ 158.522282] CPU: 0 PID: 1339 Comm: modprobe Not tainted 3.14.23-00445-gd41c88f #44
[ 158.530359] [<c0015380>] (unwind_backtrace) from [<c0012088>] (show_stack+0x10/0x14)
[ 158.538603] [<c0012088>] (show_stack) from [<c054ad70>] (dump_stack+0x78/0x94)
[ 158.546295] [<c054ad70>] (dump_stack) from [<c0088008>] (__lock_acquire+0x176c/0x1b74)
[ 158.554711] [<c0088008>] (__lock_acquire) from [<c0088944>] (lock_acquire+0x9c/0x104)
[ 158.563043] [<c0088944>] (lock_acquire) from [<c004e520>] (del_timer_sync+0x44/0xd8)
[ 158.571289] [<c004e520>] (del_timer_sync) from [<bf2eac1c>] (cpsw_ale_destroy+0x10/0x3c [ti_cpsw])
[ 158.580821] [<bf2eac1c>] (cpsw_ale_destroy [ti_cpsw]) from [<bf2eb268>] (cpsw_remove+0x30/0xa0 [ti_cpsw])
[ 158.591000] [<bf2eb268>] (cpsw_remove [ti_cpsw]) from [<c035ef44>] (platform_drv_remove+0x18/0x1c)
[ 158.600527] [<c035ef44>] (platform_drv_remove) from [<c035d8bc>] (__device_release_driver+0x70/0xc8)
[ 158.610236] [<c035d8bc>] (__device_release_driver) from [<c035e0d4>] (driver_detach+0xb4/0xb8)
[ 158.619386] [<c035e0d4>] (driver_detach) from [<c035d6e4>] (bus_remove_driver+0x4c/0x90)
[ 158.627988] [<c035d6e4>] (bus_remove_driver) from [<c00af2a8>] (SyS_delete_module+0x10c/0x198)
[ 158.637144] [<c00af2a8>] (SyS_delete_module) from [<c000e580>] (ret_fast_syscall+0x0/0x48)
[ 179.524727] INFO: rcu_sched detected stalls on CPUs/tasks: {} (detected by 0, t=2102 jiffies, g=1487, c=1486, q=6)
[ 179.535741] INFO: Stall ended before state dump start
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Karl Beldan [Wed, 5 Nov 2014 14:32:59 +0000 (15:32 +0100)]
net: mv643xx_eth: reclaim TX skbs only when released by the HW
ATM, txq_reclaim will dequeue and free an skb for each tx desc released
by the hw that has TX_LAST_DESC set. However, in case of TSO, each
hw desc embedding the last part of a segment has TX_LAST_DESC set,
losing the one-to-one 'last skb frag'/'TX_LAST_DESC set' correspondance,
which causes data corruption.
Fix this by checking TX_ENABLE_INTERRUPT instead of TX_LAST_DESC, and
warn when trying to dequeue from an empty txq (which can be symptomatic
of releasing skbs prematurely).
Fixes: 3ae8f4e0b98 ('net: mv643xx_eth: Implement software TSO') Reported-by: Slawomir Gajzner <slawomir.gajzner@gmail.com> Reported-by: Julien D'Ascenzio <jdascenzio@yahoo.fr> Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com> Cc: Ian Campbell <ijc@hellion.org.uk> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
xen-netback: remove unconditional __pskb_pull_tail() in guest Tx path
Unconditionally pulling 128 bytes into the linear area is not required
for:
- security: Every protocol demux starts with pskb_may_pull() to pull
frag data into the linear area, if necessary, before looking at
headers.
- performance: Netback has already grant copied up-to 128 bytes from
the first slot of a packet into the linear area. The first slot
normally contain all the IPv4/IPv6 and TCP/UDP headers.
The unconditional pull would often copy frag data unnecessarily. This
is a performance problem when running on a version of Xen where grant
unmap avoids TLB flushes for pages which are not accessed. TLB
flushes can now be avoided for > 99% of unmaps (it was 0% before).
Grant unmap TLB flush avoidance will be available in a future version
of Xen (probably 4.6).
Signed-off-by: Malcolm Crossley <malcolm.crossley@citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Acked-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Wed, 5 Nov 2014 09:45:32 +0000 (11:45 +0200)]
stmmac: fix sparse warnings
This patch fixes the following sparse warnings.
drivers/net/ethernet/stmicro/stmmac/enh_desc.c:381:30: warning: symbol 'enh_desc_ops' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:253:30: warning: symbol 'ndesc_ops' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c:141:33: warning: symbol 'stmmac_ptp' was not declared. Should it be static?
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Giuseppe CAVALLARO <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_tunnel: Add support for wildcard tunnel endpoints.
This patch adds support for tunnels with local or
remote wildcard endpoints. With this we get a
NBMA tunnel mode like we have it for ipv4 and
sit tunnels.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6: Allow sending packets through tunnels with wildcard endpoints
Currently we need the IP6_TNL_F_CAP_XMIT capabiltiy to transmit
packets through an ipv6 tunnel. This capability is set when the
tunnel gets configured, based on the tunnel endpoint addresses.
On tunnels with wildcard tunnel endpoints, we need to do the
capabiltiy checking on a per packet basis like it is done in
the receive path.
This patch extends ip6_tnl_xmit_ctl() to take local and remote
addresses as parameters to allow for per packet capabiltiy
checking.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Sun, 19 Oct 2014 19:03:40 +0000 (12:03 -0700)]
openvswitch: Avoid NULL mask check while building mask
OVS does mask validation even if it does not need to convert
netlink mask attributes to mask structure. ovs_nla_get_match()
caller can pass NULL mask structure pointer if the caller does
not need mask. Therefore NULL check is required in SW_FLOW_KEY*
macros. Following patch does not convert mask netlink attributes
if mask pointer is NULL, so we do not need these checks in
SW_FLOW_KEY* macro.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Daniele Di Proietto <ddiproietto@vmware.com> Acked-by: Andy Zhou <azhou@nicira.com>
Pravin B Shelar [Sun, 19 Oct 2014 18:19:51 +0000 (11:19 -0700)]
openvswitch: Refactor action alloc and copy api.
There are two separate API to allocate and copy actions list. Anytime
OVS needs to copy action list, it needs to call both functions.
Following patch moves action allocation to copy function to avoid
code duplication.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com> Acked-by: Jarno Rajahalme <jrajahalme@nicira.com>
Chunhe Li [Mon, 8 Sep 2014 20:17:21 +0000 (13:17 -0700)]
openvswitch: Drop packets when interdev is not up
If the internal device is not up, it should drop received
packets. Sometimes it receive the broadcast or multicast
packets, and the ip protocol stack will casue more cpu
usage wasted.
Signed-off-by: Chunhe Li <lichunhe@huawei.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Joe Stringer [Mon, 8 Sep 2014 20:09:37 +0000 (13:09 -0700)]
openvswitch: Refactor ovs_flow_cmd_fill_info().
Split up ovs_flow_cmd_fill_info() to make it easier to cache parts of a
dump reply. This will be used to streamline flow_dump in a future patch.
Signed-off-by: Joe Stringer <joestringer@nicira.com> Acked-by: Thomas Graf <tgraf@noironetworks.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Andy Zhou [Mon, 8 Sep 2014 07:35:02 +0000 (00:35 -0700)]
openvswitch: refactor do_output() to move NULL check out of fast path
skb_clone() NULL check is implemented in do_output(), as past of the
common (fast) path. Refactoring so that NULL check is done in the
slow path, immediately after skb_clone() is called.
Besides optimization, this change also improves code readability by
making the skb_clone() NULL check consistent within OVS datapath
module.
Signed-off-by: Andy Zhou <azhou@nicira.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Jesse Gross [Mon, 6 Oct 2014 12:08:38 +0000 (05:08 -0700)]
openvswitch: Additional logging for -EINVAL on flow setups.
There are many possible ways that a flow can be invalid so we've
added logging for most of them. This adds logs for the remaining
possible cases so there isn't any ambiguity while debugging.
CC: Federico Iezzi <fiezzi@enter.it> Signed-off-by: Jesse Gross <jesse@nicira.com> Acked-by: Thomas Graf <tgraf@noironetworks.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Simon Horman [Mon, 6 Oct 2014 12:05:13 +0000 (05:05 -0700)]
openvswitch: Add basic MPLS support to kernel
Allow datapath to recognize and extract MPLS labels into flow keys
and execute actions which push, pop, and set labels on packets.
Based heavily on work by Leo Alterman, Ravi K, Isaku Yamahata and Joe Stringer.
Cc: Ravi K <rkerur@gmail.com> Cc: Leo Alterman <lalterman@nicira.com> Cc: Isaku Yamahata <yamahata@valinux.co.jp> Cc: Joe Stringer <joe@wand.net.nz> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Jesse Gross <jesse@nicira.com> Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Pravin B Shelar [Wed, 5 Nov 2014 23:27:48 +0000 (15:27 -0800)]
net: Remove MPLS GSO feature.
Device can export MPLS GSO support in dev->mpls_features same way
it export vlan features in dev->vlan_features. So it is safe to
remove NETIF_F_GSO_MPLS redundant flag.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
hayeswang [Wed, 5 Nov 2014 02:17:02 +0000 (10:17 +0800)]
r8152: disable the tasklet by default
Let the tasklet only be enabled after open(), and be disabled for
the other situation. The tasklet is only necessary after open() for
tx/rx, so it could be disabled by default.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 5 Nov 2014 19:27:38 +0000 (20:27 +0100)]
ipv6: mld: fix add_grhead skb_over_panic for devs with large MTUs
It has been reported that generating an MLD listener report on
devices with large MTUs (e.g. 9000) and a high number of IPv6
addresses can trigger a skb_over_panic():
mld_newpack() skb allocations are usually requested with dev->mtu
in size, since commit 72e09ad107e7 ("ipv6: avoid high order allocations")
we have changed the limit in order to be less likely to fail.
However, in MLD/IGMP code, we have some rather ugly AVAILABLE(skb)
macros, which determine if we may end up doing an skb_put() for
adding another record. To avoid possible fragmentation, we check
the skb's tailroom as skb->dev->mtu - skb->len, which is a wrong
assumption as the actual max allocation size can be much smaller.
The IGMP case doesn't have this issue as commit 57e1ab6eaddc
("igmp: refine skb allocations") stores the allocation size in
the cb[].
Set a reserved_tailroom to make it fit into the MTU and use
skb_availroom() helper instead. This also allows to get rid of
igmp_skb_size().
Reported-by: Wei Liu <lw1a2.jing@gmail.com> Fixes: 72e09ad107e7 ("ipv6: avoid high order allocations") Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: David L Stevens <david.stevens@oracle.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
By default the arch_fast_hash hashing function pointers are initialized
to jhash(2). If during boot-up a CPU with SSE4.2 is detected they get
updated to the CRC32 ones. This dispatching scheme incurs a function
pointer lookup and indirect call for every hashing operation.
rhashtable as a user of arch_fast_hash e.g. stores pointers to hashing
functions in its structure, too, causing two indirect branches per
hashing operation.
Using alternative_call we can get away with one of those indirect branches.
Acked-by: Daniel Borkmann <dborkman@redhat.com> Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The following series of patches includes functional updates to the
driver as well as some trivial changes for function renaming and
spelling fixes.
- Move channel and ring structure allocation into the device open path
- Rename the pre_xmit function to dev_xmit
- Explicitly use the u32 data type for the device descriptors
- Use page allocation for the receive buffers
- Add support for split header/payload receive
- Add support for per DMA channel interrupts
- Add support for receive side scaling (RSS)
- Add support for ethtool receive side scaling commands
- Fix the spelling of descriptors
- After a PCS reset, sync the PCS and PHY modes
- Add dependency on HAS_IOMEM to both the amd-xgbe and amd-xgbe-phy
drivers
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to sync the states of the PCS and the PHY
after a reset is performed. If the PCS and the PHY are not in the
same state after reset an extra mode change would be performed. This
extra mode change might not be needed if the PCS and the PHY are
synced up after reset.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
amd-xgbe: Provide support for receive side scaling
This patch provides support for receive side scaling (RSS). RSS allows
for spreading incoming network packets across the Rx queues. When used
in conjunction with the per DMA channel interrupt support, this allows
the receive processing to be spread across multiple processors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
amd-xgbe: Add support for per DMA channel interrupts
This patch provides support for interrupts that are generated by the
Tx/Rx DMA channel pairs of the device. This allows for Tx and Rx
processing to run across multiple processsors.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Provide support for splitting IP packets so that the header and
payload can be sent to different DMA addresses. This will allow
the IP header to be put into the linear part of the skb while the
payload can be added as frags.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The pre_xmit function name implies that it performs operations prior
to transmitting the packet when in fact it is responsible for setting
up the descriptors and initiating the transmit. Rename this to
function from pre_xmit to dev_xmit, which is consistent with the name
used during receive processing - dev_read.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Move the channel and ring tracking structures allocation to device
open. This will allow for future support to vary the number of Tx/Rx
queues without unloading the module.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory Fong [Tue, 4 Nov 2014 19:21:21 +0000 (11:21 -0800)]
bridge: include in6.h in if_bridge.h for struct in6_addr
if_bridge.h uses struct in6_addr ip6, but wasn't including the in6.h
header. Thomas Backlund originally sent a patch to do this, but this
revealed a redefinition issue: https://lkml.org/lkml/2013/1/13/116
Reported-by: Colin Guthrie <colin@mageia.org> Reported-by: Christiaan Welvaart <cjw@daneel.dyndns.org> Reported-by: Thomas Backlund <tmb@mageia.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Leitner [Tue, 4 Nov 2014 19:15:08 +0000 (17:15 -0200)]
tcp: zero retrans_stamp if all retrans were acked
Ueki Kohei reported that when we are using NewReno with connections that
have a very low traffic, we may timeout the connection too early if a
second loss occurs after the first one was successfully acked but no
data was transfered later. Below is his description of it:
When SACK is disabled, and a socket suffers multiple separate TCP
retransmissions, that socket's ETIMEDOUT value is calculated from the
time of the *first* retransmission instead of the *latest*
retransmission.
This happens because the tcp_sock's retrans_stamp is set once then never
cleared.
(*1) One data packet sent.
(*2) Because no ACK packet is received, the packet is retransmitted.
(*3) The ACK packet is received. The transmitted packet is acknowledged.
At this point the first "retransmission event" has passed and been
recovered from. Any future retransmission is a completely new "event".
(*4) After 16 minutes (to correspond with retries2=15), a new data
packet is sent. Note: No data is transmitted between (*3) and (*4).
The socket's timeout SHOULD be calculated from this point in time, but
instead it's calculated from the prior "event" 16 minutes ago.
(*5) Because no ACK packet is received, the packet is retransmitted.
(*6) At the time of the 2nd retransmission, the socket returns
ETIMEDOUT.
Therefore, now we clear retrans_stamp as soon as all data during the
loss window is fully acked.
Reported-by: Ueki Kohei Cc: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Acked-by: Neal Cardwell <ncardwell@google.com> Tested-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 5 Nov 2014 21:34:47 +0000 (16:34 -0500)]
Merge branch 'gue-next'
Tom Herbert says:
====================
gue: Remote checksum offload
This patch set implements remote checksum offload for
GUE, which is a mechanism that provides checksum offload of
encapsulated packets using rudimentary offload capabilities found in
most Network Interface Card (NIC) devices. The outer header checksum
for UDP is enabled in packets and, with some additional meta
information in the GUE header, a receiver is able to deduce the
checksum to be set for an inner encapsulated packet. Effectively this
offloads the computation of the inner checksum. Enabling the outer
checksum in encapsulation has the additional advantage that it covers
more of the packet than the inner checksum including the encapsulation
headers.
Remote checksum offload is described in:
http://tools.ietf.org/html/draft-herbert-remotecsumoffload-01
The GUE transmit and receive paths are modified to support the
remote checksum offload option. The option contains a checksum
offset and checksum start which are directly derived from values
set in stack when doing CHECKSUM_PARTIAL. On receipt of the option, the
operation is to calculate the packet checksum from "start" to end of
the packet (normally derived for checksum complete), and then set
the resultant value at checksum "offset" (the checksum field has
already been primed with the pseudo header). This emulates a NIC
that implements NETIF_F_HW_CSUM.
The primary purpose of this feature is to eliminate cost of performing
checksum calculation over a packet when encpasulating.
In this patch set:
- Move fou_build_header into fou.c and split it into a couple of
functions
- Enable offloading of outer UDP checksum in encapsulation
- Change udp_offload to support remote checksum offload, includes
new GSO type and ensuring encapsulated layers (TCP) doesn't try to
set a checksum covered by RCO
- TX support for RCO with GUE. This is configured through ip_tunnel
and set the option on transmit when packet being encapsulated is
CHECKSUM_PARTIAL
- RX support for RCO with GUE for normal and GRO paths. Includes
resolving the offloaded checksum
v2:
Address comments from davem: Move accounting for private option
field in gue_encap_hlen to patch in which we add the remote checksum
offload option.
Testing:
I ran performance numbers using netperf TCP_STREAM and TCP_RR with 200
streams, comparing GUE with and without remote checksum offload (doing
checksum-unnecessary to complete conversion in both cases). These
were run on mlnx4 and bnx2x. Some mlnx4 results are below.
GRE/GUE
TCP_STREAM
IPv4, with remote checksum offload
9.71% TX CPU utilization
7.42% RX CPU utilization
36380 Mbps
IPv4, without remote checksum offload
12.40% TX CPU utilization
7.36% RX CPU utilization
36591 Mbps
TCP_RR
IPv4, with remote checksum offload
77.79% CPU utilization
91/144/216 90/95/99% latencies
1.95127e+06 tps
IPv4, without remote checksum offload
78.70% CPU utilization
89/152/297 90/95/99% latencies
1.95458e+06 tps
IPIP/GUE
TCP_STREAM
With remote checksum offload
10.30% TX CPU utilization
7.43% RX CPU utilization
36486 Mbps
Without remote checksum offload
12.47% TX CPU utilization
7.49% RX CPU utilization
36694 Mbps
TCP_RR
With remote checksum offload
77.80% CPU utilization
87/153/270 90/95/99% latencies
1.98735e+06 tps
Without remote checksum offload
77.98% CPU utilization
87/150/287 90/95/99% latencies
1.98737e+06 tps
SIT/GUE
TCP_STREAM
With remote checksum offload
9.68% TX CPU utilization
7.36% RX CPU utilization
35971 Mbps
Without remote checksum offload
12.95% TX CPU utilization
8.04% RX CPU utilization
36177 Mbps
TCP_RR
With remote checksum offload
79.32% CPU utilization
94/158/295 90/95/99% latencies
1.88842e+06 tps
Without remote checksum offload
80.23% CPU utilization
94/149/226 90/95/99% latencies
1.90338e+06 tps
VXLAN
TCP_STREAM
35.03% TX CPU utilization
20.85% RX CPU utilization
36230 Mbps
TCP_RR
77.36% CPU utilization
84/146/270 90/95/99% latencies
2.08063e+06 tps
We can also look at CPU time in csum_partial using perf (with bnx2x
setup). For GRE with TCP_STREAM I see:
With remote checksum offload
0.33% TX
1.81% RX
Without remote checksum offload
6.00% TX
0.51% RX
I suspect the fact that time in csum_partial noticably increases
with remote checksum offload for RX is due to taking the cache miss on
the encapsulated header in that function. By similar reasoning, if on
the TX side the packet were not in cache (say we did a splice from a
file whose data was never touched by the CPU) the CPU savings for TX
would probably be more pronounced.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 4 Nov 2014 17:06:57 +0000 (09:06 -0800)]
gue: Receive side of remote checksum offload
Add processing of the remote checksum offload option in both the normal
path as well as the GRO path. The implements patching the affected
checksum to derive the offloaded checksum.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 4 Nov 2014 17:06:56 +0000 (09:06 -0800)]
gue: TX support for using remote checksum offload option
Add if_tunnel flag TUNNEL_ENCAP_FLAG_REMCSUM to configure
remote checksum offload on an IP tunnel. Add logic in gue_build_header
to insert remote checksum offload option.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 4 Nov 2014 17:06:54 +0000 (09:06 -0800)]
udp: Changes to udp_offload to support remote checksum offload
Add a new GSO type, SKB_GSO_TUNNEL_REMCSUM, which indicates remote
checksum offload being done (in this case inner checksum must not
be offloaded to the NIC).
Added logic in __skb_udp_tunnel_segment to handle remote checksum
offload case.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 4 Nov 2014 17:06:53 +0000 (09:06 -0800)]
gue: Add infrastructure for flags and options
Add functions and basic definitions for processing standard flags,
private flags, and control messages. This includes definitions
to compute length of optional fields corresponding to a set of flags.
Flag validation is in validate_gue_flags function. This checks for
unknown flags, and that length of optional fields is <= length
in guehdr hlen.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 4 Nov 2014 17:06:52 +0000 (09:06 -0800)]
udp: Offload outer UDP tunnel csum if available
In __skb_udp_tunnel_segment if outer UDP checksums are enabled and
ip_summed is not already CHECKSUM_PARTIAL, set up checksum offload
if device features allow it.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Tue, 4 Nov 2014 17:06:51 +0000 (09:06 -0800)]
net: Move fou_build_header into fou.c and refactor
Move fou_build_header out of ip_tunnel.c and into fou.c splitting
it up into fou_build_header, gue_build_header, and fou_build_udp.
This allows for other users for TX of FOU or GUE. Change ip_tunnel_encap
to call fou_build_header or gue_build_header based on the tunnel
encapsulation type. Similarly, added fou_encap_hlen and gue_encap_hlen
functions which are called by ip_encap_hlen. New net/fou.h has
prototypes and defines for this.
Added NET_FOU_IP_TUNNELS configuration. When this is set, IP tunnels
can use FOU/GUE and fou module is also selected.
Signed-off-by: Tom Herbert <therbert@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 5 Nov 2014 21:23:09 +0000 (16:23 -0500)]
Merge branch 'stmmac-net'
Giuseppe Cavallaro says:
====================
stmmac: review and fix lock and atomicity
Recently some issues have been reported for the driver for locking mechanism
and atomicity.
In fact, enabling DEBUG support to prove lock and to verify if sleeping while
atomic context some warnings occur at runtime. I have reproduced all on STi
platforms.
Concerning the tx path, I had provided a patch time ago but
I discarded the idea to completely remove locks; in this patch-set we can have
some useful fixes instead of.
This patch-set is to fix the atomicity in the PM stuff where I tried to collect
all the points and advice reported in the past weeks.
As final result, on my side no warnings and no problem when suspend/resume the
driver on STi boxes.
I also added a patch that fixes the locks for the EEE.
As pointed in some thread there was a design problem behind the eee
initialization and I have tried to fix that before.
As final result no issues when proving locks too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the atomicity when suspend and resume the
driver. The clk api have been changed (as reported by Hao Liang)
and the skb allocation is done out of the hw setup function and
taking care about the GFP flags.
Reported-by: Hao Liang <hliang1025@gmail.com> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Hao Liang <hliang1025@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The patch removes the stmmac_eee_init call inside the stmmac_hw_setup
that is unnecessary. It is sufficient to call it in the adjust_link to
always guarantee that EEE is always configured at mac level too.
Fixing the lock protection now it is covered another case (not
considered before). The stmmac_eee_init could be called by the ethtool
so critical sections must be protected inside this function too.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
so the patch just removes the lock protection in the stmmac_set_rx_mode
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Emilio Lopez <emilio@elopez.com.ar> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabrice Gasnier [Tue, 4 Nov 2014 16:08:06 +0000 (17:08 +0100)]
stmmac: release tx lock, in case of dma mapping error.
Add missing spin_unlock when tx frames gets dropped.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fabrice Gasnier [Tue, 4 Nov 2014 16:08:05 +0000 (17:08 +0100)]
stmmac: fix stmmac_tx_avail should be called with TX locked
stmmac_tx_avail() may lie if used unprotected. It's using cur_tx
and dirty_tx index. These index may be already in use by tx_clean
when entering xmit routine. So, this should be called locked.
This can cause transmit queue to be stuck, with following message:
NETDEV WATCHDOG: eth0 (stmmaceth): transmit queue 0 timed out
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Recently many Koption options have been added to have new glue logic on several
platforms.
The main goal behind this work is to guarantee that the driver built
fine on all the branches where it is present independently of which
glue logic is selected.
IMHO, it is better to remove all the not necessary Koption(s) that can hide
build problems when something changes in the driver and especially when
the DT compatibility allows us to manage all the platform data.
I compiled the driver w/o any issue on net-next Git for:
x86, arm and sh4.
In case of there are build problems on some repos now it will be
easy to catch them and cherry-pick patches from mainstream.
For sure, do not hesitate to contact me in case of issue.
Also this set removes STMMAC_DEBUG_FS and BUS_MODE_DA. The latter is useless
and the former can be replaced by DEBUG_FS (always to make safe the build).
V2: patch-set re-based on top of the latest updates for net-next
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a very old and often unused option to configure
a bit in a register inside the DMA. This support should
not stay under Koption and should be extended for new chips too.
This will be do later maybe via device-tree parameters.
Also no performance impact when remove this setting on STi platforms.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
the STMMAC_DEBUG_FS Koption is now removed from the
driver configuration and this support will be built
by default when DEBUG_FS is present. This can also be
useful on building driver verification.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac: remove specific SoC Koption from platform.
This patch removes all the Koptions added to build the glue-logic files
for all different architectures: DWMAC_MESON, DWMAC_SUNXI, DWMAC_STI ...
Nowadays the stmmac needs to be compiled on several platforms; in some
case it very convenient to guarantee that its build is always completed
with success on all the branches where the driver is present.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Microblaze is a fpga soft core, it can be customized easily, which may
cause many various hardware version strings.
So the original fix patch based on hard-coded compatible version strings
is not a good idea (although it is correct for current issue). For it,
there will be a new solving way soon (which based on the device tree).
The original issue is related with qemu, so can only change the hardware
version string in qemu for it, then keep the original driver no touch (
qemu is for virtualization which has much easier life than real world).
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross [Tue, 4 Nov 2014 03:38:38 +0000 (19:38 -0800)]
geneve: Unregister pernet subsys on module unload.
The pernet ops aren't ever unregistered, which causes a memory
leak and an OOPs if the module is ever reinserted.
Fixes: 0b5e8b8eeae4 ("net: Add Geneve tunneling protocol driver") CC: Andy Zhou <azhou@nicira.com> Signed-off-by: Jesse Gross <jesse@nicira.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-beck.git / log