Mike Dunn [Wed, 25 Apr 2012 19:06:07 +0000 (12:06 -0700)]
mtd: expose ecc_strength through sysfs
ecc_strength element of struct mtd_info is exposed as a read-only variable in
sysfs.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Dunn [Wed, 25 Apr 2012 19:06:06 +0000 (12:06 -0700)]
mtd: nand: fix incorrect ecc strength values
This fixes a couple of ecc strength values for which I earlier made conservative
guesses, but whose correct values were later determined¹ (thanks Ivan). Also
sets strength for fsl_ifc_nand, which was merged to mainline after the original
patch that set the strength for all drivers.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Dunn [Wed, 25 Apr 2012 19:06:05 +0000 (12:06 -0700)]
mtd: ecc_strength is at ecc step granularity
ecc_strength element of mtd_info will be the strength of one ecc step, not of
the entire writesize, as was previously planned. This is the appropriate way
because, as was pointed out¹, bit errors in excess of the strength of one
step can cause a hard error if they all occur within the same ecc region.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd: nand: Add a NAND_CMD_STATUS when using write verification
To make sure the NAND chip is properly programmed we need a status
command before each page write. When CONFIG_MTD_NAND_VERIFY_WRITE=y this
assumption is broken when writing multiple pages consecutively. This
patch fixes this.
Xi Wang [Wed, 25 Apr 2012 18:45:22 +0000 (14:45 -0400)]
jffs2: validate symlink size in jffs2_do_read_inode_internal()
`csize' is read from disk and thus needs validation. Otherwise a bogus
value 0xffffffff would turn the subsequent kmalloc(csize + 1, ...) into
kmalloc(0, ...), leading to out-of-bounds write.
This patch limits `csize' to JFFS2_MAX_NAME_LEN, which is also used
in jffs2_symlink().
Artem: we actually validate csize by checking CRC, so this 0xFFs cannot
come from empty flash region. But I guess an attacker could feed JFFS2
an image with random csize value, including 0xFFs.
Signed-off-by: Xi Wang <xi.wang@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jonas Gorski [Thu, 19 Apr 2012 11:15:57 +0000 (13:15 +0200)]
mtd: bcm63xxpart: handle Broadcom partition order
The original Broadcom partition order has the root fs in front of the
kernel, which resulted in miscalculated partition sizes.
Detect when such an image is on the flash and also reorder the partitions
accordingly.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Ivan Djelic [Tue, 17 Apr 2012 11:11:53 +0000 (13:11 +0200)]
mtd: nand: omap: fix race condition in omap_wait()
If a context switch occurs in function omap_wait() just before the
while loop is entered, then upon return from context switch the
timeout may already have elapsed: in that case, status is never
read from NAND device, and omap_wait() returns an error.
This failure has been experimentally observed during stress tests.
This patch ensures a NAND status read is always performed before
returning, as in the generic nand_wait() function.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
Randy Dunlap [Mon, 16 Apr 2012 19:50:37 +0000 (12:50 -0700)]
mtd: fix scb2_flash build when PCI is not enabled
scb2_flash.c is a PCI driver, but its build fails when CONFIG_PCI
is not enabled, so make it depend on PCI.
drivers/mtd/maps/scb2_flash.c:237:1: warning: data definition has no type or storage class
drivers/mtd/maps/scb2_flash.c:237:1: warning: type defaults to 'int' in declaration of 'module_pci_driver'
drivers/mtd/maps/scb2_flash.c:237:1: warning: parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Daniel Drake [Tue, 10 Apr 2012 21:22:35 +0000 (22:22 +0100)]
JFFS2: Add parameter to reserve disk space for root
Add a new rp_size= parameter which creates a "reserved pool" of disk
space which can only be used by root. Other users are not permitted
to write to disk when the available space is less than the pool size.
Based on original code by Artem Bityutskiy in
https://dev.laptop.org/ticket/5317
[dwmw2: use capable(CAP_SYS_RESOURCE) not uid/gid check, fix debug prints] Signed-off-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd: print out the page size and oob size after parsing out the nand
Some not-supported nand chips may pass the current parsing code,
and get the wrong page size and oob size. Sometimes, it's hard to notice
that you get the wrong values, because there is no warning or error.
So it's useful to print out the page size and oob size in the end of
the parsing function. We can check these values with the datasheet of the nand
chip as soon as possible.
Axel Lin [Tue, 3 Apr 2012 01:59:44 +0000 (09:59 +0800)]
mtd: use module_pci_driver
This patch converts the drivers in drivers/mtd/* to use module_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Uwe Kleine-König [Thu, 29 Mar 2012 21:12:32 +0000 (23:12 +0200)]
mtd: mark const init data with __initconst instead of __initdata
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Use the default partition parser, cmdlinepart, provided by the plat_nand driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Alexander Clouter <alex@digriz.org.uk> Acked-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Linus Torvalds [Sun, 13 May 2012 18:33:09 +0000 (11:33 -0700)]
Merge tag 'for-linus-3.4-20120513' of git://git.infradead.org/linux-mtd
Pull three MTD fixes from David Woodhouse:
- Fix a lock ordering deadlock in JFFS2
- Fix an oops in the dataflash driver, triggered by a dummy call to test
whether it has OTP functionality.
- Fix request_mem_region() failure on amsdelta NAND driver.
* tag 'for-linus-3.4-20120513' of git://git.infradead.org/linux-mtd:
mtd: ams-delta: fix request_mem_region() failure
jffs2: Fix lock acquisition order bug in gc path
mtd: fix oops in dataflash driver
Linus Torvalds [Sun, 13 May 2012 00:27:41 +0000 (17:27 -0700)]
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM: SoC fixes from Olof Johansson:
"I was hoping to be done with fixes for 3.4 but we got two branches
from subarch maintainers the last couple of days. So here is one
last(?) pull request for arm-soc containing 7 patches:
- Five of them are for shmobile dealing with SMP setup and compile
failures
- The remaining two are for regressions on the Samsung platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
Linus Torvalds [Sun, 13 May 2012 00:24:29 +0000 (17:24 -0700)]
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull a few more GPIO bug fixes from Grant Likely:
"Oops, missed a couple. Here's an updated pull req for GPIO"
A set of PCH bug fixes, and one patch to fix up compile warnings
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
gpio: pch9: Use proper flow type handlers
Olof Johansson [Sat, 12 May 2012 22:41:22 +0000 (15:41 -0700)]
Merge branch 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.4-samsung-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: fix ctrlbit for exynos5_clk_pdma1
ARM: EXYNOS: use s5p-timer for UniversalC210 board
Marek Szyprowski [Fri, 11 May 2012 21:17:59 +0000 (06:17 +0900)]
ARM: EXYNOS: use s5p-timer for UniversalC210 board
Commit 069d4e743 ("ARM: EXYNOS4: Remove clock event timers using
ARM private timers") removed support for local timers and forced
to use MCT as event source. However MCT is not operating properly
on early revision of EXYNOS4 SoCs. All UniversalC210 boards are
based on it, so that commit broke support for it. This patch
provides a workaround that enables UniversalC210 boards to boot
again. s5p-timer is used as an event source, it works only for
non-SMP builds.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Olof Johansson [Sat, 12 May 2012 22:40:56 +0000 (15:40 -0700)]
Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas into fixes
By Guennadi Liakhovetski (2) and others via Rafael J. Wysocki:
"[...] urgent fixes for Renesas ARM-based platforms. Four of these
commits are fixes of regressions new in 3.4-rc and the last one is
necessary for SMP to work on those systems in general."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM / mach-shmobile: Invalidate caches when booting secondary cores
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
Magnus Damm [Wed, 9 May 2012 07:24:59 +0000 (16:24 +0900)]
ARM / mach-shmobile: Invalidate caches when booting secondary cores
Make sure L1 caches are invalidated when booting secondary
cores. Needed to boot all mach-shmobile SMP systems that
are using Cortex-A9 including sh73a0, r8a7779 and EMEV2.
Thanks to imx and tegra guys for actual code.
Signed-off-by: Magnus Damm <damm@opensource.se> Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
ARM / mach-shmobile: sh73a0 SMP TWD boot regression fix
Fix SMP TWD boot regression on sh73a0 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
sh73a0 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on sh73a0 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
This patch removed shmobile_twd_init() which is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Magnus Damm <damm@opensource.se> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Magnus Damm [Thu, 10 May 2012 05:57:22 +0000 (14:57 +0900)]
ARM / mach-shmobile: r8a7779 SMP TWD boot regression fix
Fix SMP TWD boot regression on r8a7779 based platforms caused by:
4200b16 ARM: shmobile: convert to twd_local_timer_register() interface
After the merge of the above commit it has been impossible to boot
r8a7779 based SoCs with SMP enabled and CONFIG_HAVE_ARM_TWD=y. The
kernel crashes at smp_init_cpus() timing which is before the console
has been initialized, so to the user this looks like a kernel lock up
without any particular error message.
This patch fixes the regression on r8a7779 by moving the TWD
registration code from smp_init_cpus() to sys_timer->init() time.
Signed-off-by: Magnus Damm <damm@opensource.se> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
ARM: mach-shmobile: convert ag5evm to use the generic MMC GPIO hotplug helper
This also fixes the following modular mmc build failure:
arch/arm/mach-shmobile/built-in.o: In function `mackerel_sdhi0_gpio_cd':
pfc-sh7372.c:(.text+0x1138): undefined reference to `mmc_detect_change'
on this platform by eliminating the use of an inline function, which
calls into the mmc core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Reviewed-by: Simon Horman <horms@verge.net.au> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
ARM: mach-shmobile: convert mackerel to use the generic MMC GPIO hotplug helper
This also fixes the following modular mmc build failure:
arch/arm/mach-shmobile/built-in.o: In function `ag5evm_sdhi0_gpio_cd':
pfc-sh73a0.c:(.text+0x7c0): undefined reference to `mmc_detect_change'
on this platform by eliminating the use of an inline function, which
calls into the mmc core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Tested-by: Simon Horman <horms@verge.net.au> Acked-by: Magnus Damm <damm@opensource.se> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Linus Torvalds [Sat, 12 May 2012 20:02:31 +0000 (13:02 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of minor qla and virto fixes plus one major regression
fix (oops in all legacy host drivers)."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] virtio_scsi: fix TMF use-after-free
[SCSI] fix oops in all legacy host adapters caused by 6f381fa
[SCSI] qla2xxx: Update version number to 8.04.00.03-k.
[SCSI] qla2xxx: Properly check for current state after the fabric-login request.
[SCSI] qla2xxx: Proper completion to scsi-ml for scsi status task_set_full and busy.
[SCSI] qla2xxx: Block flash access from application when device is initialized for ISP82xx.
[SCSI] qla2xxx: Fix reset time out as qla2xxx not ack to reset request.
1) Since we do RCU lookups on ipv4 FIB entries, we have to test if the
entry is dead before returning it to our caller.
2) openvswitch locking and packet validation fixes from Ansis Atteka,
Jesse Gross, and Pravin B Shelar.
3) Fix PM resume locking in IGB driver, from Benjamin Poirier.
4) Fix VLAN header handling in vhost-net and macvtap, from Basil Gor.
5) Revert a bogus network namespace isolation change that was causing
regressions on S390 networking devices.
6) If bonding decides to process and handle a LACPDU frame, we
shouldn't bump the rx_dropped counter. From Jiri Bohac.
7) Fix mis-calculation of available TX space in r8169 driver when doing
TSO, which can lead to crashes and/or hung device. From Julien
Ducourthial.
8) SCTP does not validate cached routes properly in all cases, from
Nicolas Dichtel.
9) Link status interrupt needs to be handled in ks8851 driver, from
Stephen Boyd.
10) Use capable(), not cap_raised(), in connector/userns netlink code.
From Eric W. Biederman via Andrew Morton.
11) Fix pktgen OOPS on module unload, from Eric Dumazet.
12) iwlwifi under-estimates SKB truesizes, also from Eric Dumazet.
13) Cure division by zero in SFC driver, from Ben Hutchings.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
ks8851: Update link status during link change interrupt
macvtap: restore vlan header on user read
vhost-net: fix handle_rx buffer size
bonding: don't increase rx_dropped after processing LACPDUs
connector/userns: replace netlink uses of cap_raised() with capable()
sctp: check cached dst before using it
pktgen: fix crash at module unload
Revert "net: maintain namespace isolation between vlan and real device"
ehea: fix losing of NEQ events when one event occurred early
igb: fix rtnl race in PM resume path
ipv4: Do not use dead fib_info entries.
r8169: fix unsigned int wraparound with TSO
sfc: Fix division by zero when using one RX channel and no SR-IOV
openvswitch: Validation of IPv6 set port action uses IPv4 header
net: compare_ether_addr[_64bits]() has no ordering
cdc_ether: Ignore bogus union descriptor for RNDIS devices
bnx2x: bug fix when loading after SAN boot
e1000: Silence sparse warnings by correcting type
igb, ixgbe: netdev_tx_reset_queue incorrectly called from tx init path
openvswitch: Release rtnl_lock if ovs_vport_cmd_build_info() failed.
...
Linus Torvalds [Sat, 12 May 2012 19:56:08 +0000 (12:56 -0700)]
Merge tag 'dm-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper fixes from Alasdair G Kergon:
"Fix a couple of serious memory leaks in device-mapper thin
provisioning and tidy its MODULE_DESCRIPTION.
Mitigate occasional reported hangs associated with multipath scsi_dh
module loading."
* tag 'dm-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm mpath: check if scsi_dh module already loaded before trying to load
dm thin: correct module description
dm thin: fix unprotected use of prepared_discards list
dm thin: reinstate missing mempool_free in cell_release_singleton
Since cpufreq has no official maintainer at the moment, I'm willing
to maintain it along some other power management core code I've been
maintaining already.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Snitzer [Sat, 12 May 2012 00:43:21 +0000 (01:43 +0100)]
dm mpath: check if scsi_dh module already loaded before trying to load
If the requested scsi_dh module is already loaded then skip
request_module().
Multipath table loads can hang in an unnecessary __request_module.
Reported-by: Ben Marzinski <bmarzins@redhat.com> Cc: stable@kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mike Snitzer [Sat, 12 May 2012 00:43:16 +0000 (01:43 +0100)]
dm thin: fix unprotected use of prepared_discards list
Fix two places in commit 104655fd4dce ("dm thin: support discards") that
didn't use pool->lock to protect against concurrent changes to the
prepared_discards list.
Without this fix, thin_endio() can race with process_discard(), leading
to concurrent list_add()s that result in the processes locking up with
an error like the following:
Mike Snitzer [Sat, 12 May 2012 00:43:12 +0000 (01:43 +0100)]
dm thin: reinstate missing mempool_free in cell_release_singleton
Fix a significant memory leak inadvertently introduced during
simplification of cell_release_singleton() in commit 6f94a4c45a6f744383f9f695dde019998db3df55 ("dm thin: fix stacked bi_next
usage").
A cell's hlist_del() must be accompanied by a mempool_free().
Use __cell_release() to do this, like before.
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
gpio/exynos: Fix compiler warnings when non-exynos machines are selected
Fixes the following compiler warnings:
drivers/gpio/gpio-samsung.c: In function ‘samsung_gpiolib_init’:
drivers/gpio/gpio-samsung.c:2980:1: warning: label ‘err_ioremap1’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2978:1: warning: label ‘err_ioremap2’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2976:1: warning: label ‘err_ioremap3’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2974:1: warning: label ‘err_ioremap4’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2722:55: warning: unused variable ‘gpio_base4’ [-Wunused-variable]
drivers/gpio/gpio-samsung.c:455:32: warning: ‘exynos_gpio_cfg’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2126:33: warning: ‘exynos4_gpios_1’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2228:33: warning: ‘exynos4_gpios_2’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2373:33: warning: ‘exynos4_gpios_3’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Thomas Gleixner [Sat, 28 Apr 2012 08:13:45 +0000 (10:13 +0200)]
gpio: pch9: Use proper flow type handlers
Jean-Francois Dagenais reported:
Configuring a gpio pin with the gpio-pch driver with
"IRQF_TRIGGER_LOW | IRQF_ONESHOT" generates an interrupt storm for
threaded ISR until the ISR thread actually gets to physically clear
the interrupt on the triggering chip!! The immediate observable
symptom is the high CPU usage for my ISR thread task and the
interrupt count in /proc/interrupts incrementing radically.
The driver is wrong in several ways:
1) Using handle_simple_irq() does not provide proper flow control
handling. In the case of oneshot threaded handlers for the
demultiplexed interrupts this results in an interrupt storm because
the simple handler does not deal with masking/unmasking. Even
without threaded oneshot handlers an interrupt storm for level type
interrupts can easily be triggered when the interrupt is disabled
and the interrupt line is activated from the device.
2) Acknowlegding the demultiplexed interrupt before calling the
handler is wrong for level type interrupts.
3) The set_type function unconditionally enables the interrupt. It's
supposed to set the type and nothing else. The unmasking is done by
the core code.
Move the acknowledge code into a separate function and add it to the
demux irqchip callbacks.
Remove the unconditional enabling from the set_type() callback and set
the proper flow handlers depending on the selected type (level/edge).
Reported-and-tested-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Linus Torvalds [Fri, 11 May 2012 23:58:14 +0000 (16:58 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull another powerpc irq fix from Benjamin Herrenschmidt:
"It looks like my previous fix for the lazy irq masking problem wasn't
quite enough. There was another problem related to performance
monitor interrupts acting as NMIs leaving the flags in an incorrect
state. Here's a fix that finally seems to make perf solid again."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/irq: Fix another case of lazy IRQ state getting out of sync
Linus Torvalds [Fri, 11 May 2012 23:49:09 +0000 (16:49 -0700)]
Merge branch '3.4-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull target fix from Nicholas Bellinger:
"This patch removes some incorrect legacy code to free se_lun_acl
memory in the NodeACL release path that could potentially trigger an
OOPS during shutdown once dynamic -> explicit initiator NodeACL
conversion has occurred.
That said, we've been able to trigger an OOPS in v4.0 code for this
special case when the associated MappedLUNs had not also been made
explicit based on active TPG LUN layout during the conversion, so it
really makes senses to go ahead and drop this extra cruft to avoid any
possible issues here.
This ends up only effecting iscsi-target module code (it's the only
user) and is CC'ed to stable."
* '3.4-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Drop incorrect se_lun_acl release for dynamic -> explict ACL conversion
powerpc/irq: Fix another case of lazy IRQ state getting out of sync
So we have another case of paca->irq_happened getting out of
sync with the HW irq state. This can happen when a perfmon
interrupt occurs while soft disabled, as it will return to a
soft disabled but hard enabled context while leaving a stale
PACA_IRQ_HARD_DIS flag set.
This patch fixes it, and also adds a test for the condition
of those flags being out of sync in arch_local_irq_restore()
when CONFIG_TRACE_IRQFLAGS is enabled.
This helps catching those gremlins faster (and so far I
can't seem see any anymore, so that's good news).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Stephen Boyd [Thu, 10 May 2012 12:51:30 +0000 (12:51 +0000)]
ks8851: Update link status during link change interrupt
If a link change interrupt comes in we just clear the interrupt
and continue along without notifying the upper networking layers
that the link has changed. Use the mii_check_link() function to
update the link status whenever a link change interrupt occurs.
Cc: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Basil Gor [Thu, 3 May 2012 22:55:24 +0000 (22:55 +0000)]
macvtap: restore vlan header on user read
Ethernet vlan header is not on the packet and kept in the skb->vlan_tci
when it comes from lower dev. This patch inserts vlan header in user
buffer during skb copy on user read.
Signed-off-by: Basil Gor <basil.gor@gmail.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
target: Drop incorrect se_lun_acl release for dynamic -> explict ACL conversion
This patch removes some potentially problematic legacy code within
core_clear_initiator_node_from_tpg() that was originally intended to
release left over se_lun_acl setup during dynamic NodeACL+MappedLUN
generate when running with TPG demo-mode operation.
Since we now only ever expect to allocate and release se_lun_acl from
within target_core_fabric_configfs.c:target_fabric_make_mappedlun() and
target_fabric_drop_mappedlun() context respectively, this code for
demo-mode release is incorrect and needs to be removed.
Cc: Christoph Hellwig <hch@lst.de> Cc: Andy Grover <agrover@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Linus Torvalds [Fri, 11 May 2012 16:28:35 +0000 (09:28 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull a m68knommu fix from Greg Ungerer:
"It contains a single fix for including the ColdFire QSPI interface
setup code when enabled as a module. This was broken in the
consolidation of the ColdFire SoC device tables in the 3.4 merge
window."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: enable qspi support when SPI_COLDFIRE_QSPI = m
Hugh Dickins [Fri, 11 May 2012 08:00:07 +0000 (01:00 -0700)]
mm: raise MemFree by reverting percpu_pagelist_fraction to 0
Why is there less MemFree than there used to be? It perturbed a test,
so I've just been bisecting linux-next, and now find the offender went
upstream yesterday.
Commit 93278814d359 "mm: fix division by 0 in percpu_pagelist_fraction()"
mistakenly initialized percpu_pagelist_fraction to the sysctl's minimum 8,
which leaves 1/8th of memory on percpu lists (on each cpu??); but most of
us expect it to be left unset at 0 (and it's not then used as a divisor).
MemTotal: 8061476kB 8061476kB 8061476kB 8061476kB 8061476kB 8061476kB
Repetitive test with percpu_pagelist_fraction 8:
MemFree: 6948420kB 6237172kB 6949696kB 6840692kB 6949048kB 6862984kB
Same test with percpu_pagelist_fraction back to 0:
MemFree: 7945000kB 7944908kB 7948568kB 7949060kB 7948796kB 7948812kB
Signed-off-by: Hugh Dickins <hughd@google.com>
[ We really should fix the crazy sysctl interface too, but that's a
separate thing - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Bohac [Wed, 9 May 2012 01:01:40 +0000 (01:01 +0000)]
bonding: don't increase rx_dropped after processing LACPDUs
Since commit 3aba891d, bonding processes LACP frames (802.3ad
mode) with bond_handle_frame(). Currently a copy of the skb is
made and the original is left to be processed by other
rx_handlers and the rest of the network stack by returning
RX_HANDLER_ANOTHER. As there is no protocol handler for
PKT_TYPE_LACPDU, the frame is dropped and dev->rx_dropped
increased.
Fix this by making bond_handle_frame() return RX_HANDLER_CONSUMED
if bonding has processed the LACP frame.
Signed-off-by: Jiri Bohac <jbohac@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
connector/userns: replace netlink uses of cap_raised() with capable()
In 2009 Philip Reiser notied that a few users of netlink connector
interface needed a capability check and added the idiom
cap_raised(nsp->eff_cap, CAP_SYS_ADMIN) to a few of them, on the premise
that netlink was asynchronous.
In 2011 Patrick McHardy noticed we were being silly because netlink is
synchronous and removed eff_cap from the netlink_skb_params and changed
the idiom to cap_raised(current_cap(), CAP_SYS_ADMIN).
Looking at those spots with a fresh eye we should be calling
capable(CAP_SYS_ADMIN). The only reason I can see for not calling capable
is that it once appeared we were not in the same task as the caller which
would have made calling capable() impossible.
In the initial user_namespace the only difference between between
cap_raised(current_cap(), CAP_SYS_ADMIN) and capable(CAP_SYS_ADMIN) are a
few sanity checks and the fact that capable(CAP_SYS_ADMIN) sets
PF_SUPERPRIV if we use the capability.
Since we are going to be using root privilege setting PF_SUPERPRIV seems
the right thing to do.
The motivation for this that patch is that in a child user namespace
cap_raised(current_cap(),...) tests your capabilities with respect to that
child user namespace not capabilities in the initial user namespace and
thus will allow processes that should be unprivielged to use the kernel
services that are only protected with cap_raised(current_cap(),..).
To fix possible user_namespace issues and to just clean up the code
replace cap_raised(current_cap(), CAP_SYS_ADMIN) with
capable(CAP_SYS_ADMIN).
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Patrick McHardy <kaber@trash.net> Cc: Philipp Reisner <philipp.reisner@linbit.com> Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com> Acked-by: Andrew G. Morgan <morgan@kernel.org> Cc: Vasiliy Kulikov <segoon@openwall.com> Cc: David Howells <dhowells@redhat.com> Reviewed-by: James Morris <james.l.morris@oracle.com> Cc: David Miller <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Fri, 4 May 2012 05:24:54 +0000 (05:24 +0000)]
sctp: check cached dst before using it
dst_check() will take care of SA (and obsolete field), hence
IPsec rekeying scenario is taken into account.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Vlad Yaseivch <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
ehea: fix losing of NEQ events when one event occurred early
The NEQ interrupt is only triggered when there was no previous pending
interrupt. If we request irq handling after an interrupt has occurred,
we will never get an interrupt until we call H_RESET_EVENTS.
Events seem to be cleared when we first register the NEQ. So, when we
requested irq handling right after registering it, a possible race with
an interrupt was much less likely. Now, there is a chance we may lose
this race and never get any events.
The fix here is to poll and acknowledge any events that might have
happened right after registering the irq handler.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Poirier [Thu, 10 May 2012 15:38:37 +0000 (15:38 +0000)]
igb: fix rtnl race in PM resume path
Since the caller (PM resume code) is not the one holding rtnl, when taking the
'else' branch rtnl may be released at any moment, thereby defeating the whole
purpose of this code block.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 10 May 2012 22:18:41 +0000 (15:18 -0700)]
Merge branch 'parisc' (PA-RISC compile fixes)
Merge PA-RISC compile fixes from Rolf Eike Beer:
"Since commit d66acc39c7ce ("bitops: Optimise get_order()") getorder.h
includes log2.h which leads to an include loop on PA-RISC, bringing a
bunch of other breakage to light. This patchset fixes the compilation
of the current state of 3.4 on HPPA.
Unchanged against the first version, just added an Ack by Grant."
* emailed from Rolf Eike Beer <eike-kernel@sf-tec.de>: (5 patches)
parisc: move definition of PAGE0 to asm/page.h
parisc: add missing include of asm/page.h to asm/pgtable.h
parisc: drop include of asm/pdc.h from asm/hardware.h
parisc: add missing forward declarations in asm/hardware.h
parisc: add missing includes in asm/spinlock.h
Linus Torvalds [Thu, 10 May 2012 22:17:24 +0000 (15:17 -0700)]
Merge branch 'akpm' (Andrew's patch-bomb)
Merge misc fixes from Andrew Morton.
* emailed from Andrew Morton <akpm@linux-foundation.org>: (8 patches)
MAINTAINERS: add maintainer for LED subsystem
mm: nobootmem: fix sign extend problem in __free_pages_memory()
drivers/leds: correct __devexit annotations
memcg: free spare array to avoid memory leak
namespaces, pid_ns: fix leakage on fork() failure
hugetlb: prevent BUG_ON in hugetlb_fault() -> hugetlb_cow()
mm: fix division by 0 in percpu_pagelist_fraction()
proc/pid/pagemap: correctly report non-present ptes and holes between vmas
This was defined in asm/pdc.h which needs to include asm/page.h for
__PAGE_OFFSET. This leads to an include loop so that page.h eventually will
include pdc.h again. While this is no problem because of header guards, it is
a problem because some symbols may be undefined. Such an error is this:
In file included from include/linux/bitops.h:35:0,
from include/asm-generic/getorder.h:7,
from arch/parisc/include/asm/page.h:162,
from arch/parisc/include/asm/pdc.h:346,
from arch/parisc/include/asm/processor.h:16,
from arch/parisc/include/asm/spinlock.h:6,
from arch/parisc/include/asm/atomic.h:20,
from include/linux/atomic.h:4,
from include/linux/sysfs.h:20,
from include/linux/kobject.h:21,
from include/linux/device.h:17,
from include/linux/eisa.h:5,
from arch/parisc/kernel/pci.c:11:
arch/parisc/include/asm/bitops.h: In function ‘set_bit’:
arch/parisc/include/asm/bitops.h:82:2: error: implicit declaration of function ‘_atomic_spin_lock_irqsave’ [-Werror=implicit-function-declaration]
arch/parisc/include/asm/bitops.h:84:2: error: implicit declaration of function ‘_atomic_spin_unlock_irqrestore’ [-Werror=implicit-function-declaration]
parisc: add missing include of asm/page.h to asm/pgtable.h
Fixes these errors:
In file included from arch/parisc/include/asm/io.h:5:0,
from include/linux/io.h:22,
from include/linux/pci.h:54,
from arch/parisc/kernel/setup.c:35:
arch/parisc/include/asm/pgtable.h:92:6: warning: "PAGE_SHIFT" is not defined [-Wundef]
arch/parisc/include/asm/pgtable.h:92:6: warning: "PAGE_SHIFT" is not defined [-Wundef]
arch/parisc/include/asm/pgtable.h:92:6: warning: "BITS_PER_PTE_ENTRY" is not defined [-Wundef]
parisc: drop include of asm/pdc.h from asm/hardware.h
It seems none of the symbols defined by pdc.h is needed, but it introduces an
include loop causing compile errors:
In file included from arch/parisc/include/asm/spinlock.h:4:0,
from arch/parisc/include/asm/atomic.h:20,
from include/linux/atomic.h:4,
from arch/parisc/include/asm/bitops.h:56,
from include/linux/bitops.h:35,
from include/asm-generic/getorder.h:7,
from arch/parisc/include/asm/page.h:162,
from arch/parisc/include/asm/pdc.h:346,
from arch/parisc/include/asm/hardware.h:5,
from arch/parisc/kernel/hardware.c:30:
arch/parisc/include/asm/processor.h:74:16: error: field ‘cpu_type’ has incomplete type
arch/parisc/include/asm/processor.h:77:20: error: field ‘model’ has incomplete type
arch/parisc/include/asm/processor.h: In function ‘parisc_requires_coherency’:
arch/parisc/include/asm/processor.h:349:36: error: ‘mako’ undeclared (first use in this function)
arch/parisc/include/asm/processor.h:349:36: note: each undeclared identifier is reported only once for each function it appears in
arch/parisc/include/asm/processor.h:350:30: error: ‘mako2’ undeclared (first use in this function)
parisc: add missing forward declarations in asm/hardware.h
Fixes this warnings:
In file included from arch/parisc/include/asm/processor.h:15:0,
from arch/parisc/include/asm/spinlock.h:4,
from arch/parisc/include/asm/atomic.h:20,
from include/linux/atomic.h:4,
from arch/parisc/include/asm/bitops.h:11,
from include/linux/bitops.h:22,
from include/linux/kernel.h:19,
from include/linux/sched.h:55,
from arch/parisc/kernel/asm-offsets.c:31:
arch/parisc/include/asm/hardware.h:106:10: warning: ‘struct hardware_path’ declared inside parameter list [enabled by default]
arch/parisc/include/asm/hardware.h:106:10: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
arch/parisc/include/asm/hardware.h:116:59: warning: ‘struct hardware_path’ declared inside parameter list [enabled by default]
arch/parisc/include/asm/hardware.h:118:47: warning: ‘struct hardware_path’ declared inside parameter list [enabled by default]
arch/parisc/include/asm/hardware.h:119:57: warning: ‘struct hardware_path’ declared inside parameter list [enabled by default]
In file included from arch/parisc/include/asm/atomic.h:20:0,
from include/linux/atomic.h:4,
from arch/parisc/include/asm/bitops.h:56,
from include/linux/bitops.h:22,
from include/linux/kernel.h:19,
from include/linux/sched.h:55,
from arch/parisc/kernel/asm-offsets.c:31:
arch/parisc/include/asm/spinlock.h: In function ‘arch_spin_is_locked’:
arch/parisc/include/asm/spinlock.h:9:2: error: implicit declaration of function ‘__ldcw_align’ [-Werror=implicit-function-declaration]
arch/parisc/include/asm/spinlock.h:9:29: warning: initialization makes pointer from integer without a cast [enabled by default]
arch/parisc/include/asm/spinlock.h: In function ‘arch_spin_lock_flags’:
arch/parisc/include/asm/spinlock.h:22:2: error: implicit declaration of function ‘mb’ [-Werror=implicit-function-declaration]
arch/parisc/include/asm/spinlock.h:23:4: warning: assignment makes pointer from integer without a cast [enabled by default]
arch/parisc/include/asm/spinlock.h:24:2: error: implicit declaration of function ‘__ldcw’ [-Werror=implicit-function-declaration]
Russ Anderson [Thu, 10 May 2012 20:01:46 +0000 (13:01 -0700)]
mm: nobootmem: fix sign extend problem in __free_pages_memory()
Systems with 8 TBytes of memory or greater can hit a problem where only
the the first 8 TB of memory shows up. This is due to "int i" being
smaller than "unsigned long start_aligned", causing the high bits to be
dropped.
The fix is to change `i' to unsigned long to match start_aligned
and end_aligned.
Thanks to Jack Steiner for assistance tracking this down.
Signed-off-by: Russ Anderson <rja@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Tejun Heo <tj@kernel.org> Cc: David S. Miller <davem@davemloft.net> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Gavin Shan <shangw@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Thu, 10 May 2012 20:01:46 +0000 (13:01 -0700)]
drivers/leds: correct __devexit annotations
__devexit functions are discarded without CONFIG_HOTPLUG, so they need
to be referenced carefully. A __devexit function may also not be called
from a __devinit function.
Mike Galbraith [Thu, 10 May 2012 20:01:45 +0000 (13:01 -0700)]
namespaces, pid_ns: fix leakage on fork() failure
Fork() failure post namespace creation for a child cloned with
CLONE_NEWPID leaks pid_namespace/mnt_cache due to proc being mounted
during creation, but not unmounted during cleanup. Call
pid_ns_release_proc() during cleanup.
Signed-off-by: Mike Galbraith <efault@gmx.de> Acked-by: Oleg Nesterov <oleg@redhat.com> Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Louis Rilling <louis.rilling@kerlabs.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Metcalf [Thu, 10 May 2012 20:01:44 +0000 (13:01 -0700)]
hugetlb: prevent BUG_ON in hugetlb_fault() -> hugetlb_cow()
Commit 66aebce747eaf ("hugetlb: fix race condition in hugetlb_fault()")
added code to avoid a race condition by elevating the page refcount in
hugetlb_fault() while calling hugetlb_cow().
However, one code path in hugetlb_cow() includes an assertion that the
page count is 1, whereas it may now also have the value 2 in this path.
The consensus is that this BUG_ON has served its purpose, so rather than
extending it to cover both cases, we just remove it.
Sasha Levin [Thu, 10 May 2012 20:01:44 +0000 (13:01 -0700)]
mm: fix division by 0 in percpu_pagelist_fraction()
percpu_pagelist_fraction_sysctl_handler() has only considered -EINVAL as
a possible error from proc_dointvec_minmax().
If any other error is returned, it would proceed to divide by zero since
percpu_pagelist_fraction wasn't getting initialized at any point. For
example, writing 0 bytes into the proc file would trigger the issue.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com> Reviewed-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 10 May 2012 21:59:50 +0000 (14:59 -0700)]
Merge branch 'for-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu fixes from Tejun Heo:
"This pull request contains two patches. One is kmemleak annotation
fix which isn't critical. The other is kinda serious.
Depending on NUMA topology, percpu allocator may end up assigning
overlapping regions for the static percpu areas for different CPUs.
While critical, the bug has been there for a very long time and only
few configurations seem to be affected (NUMA configurations w/ no
memory nodes for example) - so, while it's critical, it isn't exactly
urgent."
* 'for-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
kmemleak: Fix the kmemleak tracking of the percpu areas with !SMP
percpu: pcpu_embed_first_chunk() should free unused parts after all allocs are complete
David S. Miller [Thu, 10 May 2012 18:00:46 +0000 (11:00 -0700)]
sparc64: Do not clobber %g2 in xcall_fetch_glob_regs().
%g2 is meant to hold the CPUID number throughout this routine, since
at the very beginning, and at the very end, we use %g2 to calculate
indexes into per-cpu arrays.
However we erroneously clobber it in order to hold the %cwp register
value mid-stream.
Fix this code to use %g3 for the %cwp read and related calulcations
instead.
Reported-by: Meelis Roos <mroos@linux.ee> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 10 May 2012 17:05:19 +0000 (10:05 -0700)]
Merge tag 'nfs-for-3.4-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull a NFS client bugfix from Trond Myklebust:
"Fix for the NFSv4 security negotiation: ensure that the security
negotiation tries all registered security flavours"
* tag 'nfs-for-3.4-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
auth_gss: the list of pseudoflavors not being parsed correctly
Linus Torvalds [Thu, 10 May 2012 16:26:58 +0000 (09:26 -0700)]
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Slightly more than expected as rc7, but all are reasonablly small
fixes. A few additions of HD-audio fixup entries, a couple of other
regression fixes including a revert, and a few other trivial
oneliners."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: sh: fix migor.c compilation
ALSA: HDA: Lessen CPU usage when waiting for chip to respond
Revert "ALSA: hda - Set codec to D3 forcibly even if not used"
ALSA: hda/realtek - Call alc_auto_parse_customize_define() always after fixup
ALSA: hdsp - Provide ioctl_compat
ALSA: hda/realtek - Add missing CD-input pin for MSI-7350 mobo
ALSA: hda/realtek - Add a fixup for Acer Aspire 5739G
ALSA: echoaudio: Remove incorrect part of assertion
Jan Kiszka [Thu, 10 May 2012 13:04:36 +0000 (10:04 -0300)]
compat: Fix RT signal mask corruption via sigprocmask
compat_sys_sigprocmask reads a smaller signal mask from userspace than
sigprogmask accepts for setting. So the high word of blocked.sig[0]
will be cleared, releasing any potentially blocked RT signal.
This was discovered via userspace code that relies on get/setcontext.
glibc's i386 versions of those functions use sigprogmask instead of
rt_sigprogmask to save/restore signal mask and caused RT signal
unblocking this way.
As suggested by Linus, this replaces the sys_sigprocmask based compat
version with one that open-codes the required logic, including the merge
of the existing blocked set with the new one provided on SIG_SETMASK.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / karo-tx-linux.git / log