tomas petr [Wed, 20 May 2009 08:28:05 +0000 (05:28 -0300)]
V4L/DVB (11830): dib0700: add support for Leadtek WinFast DTV Dongle H
"Leadtek WinFast DTV Dongle H" is a hybrid digital/analog USB-stick TV
receiver. The code below allows the digital part to work with dvb_usb
in linux.
Signed-off-by: tomas petr <tom-petr@seznam.cz> Signed-off-by: Patrick Boettcher <pb@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (11810): em28xx: properly set packet size based on the device's eeprom configuration.
The em28xx actually has a register that tells the driver what the maximum
packet size is (based on a value programmed into the eeprom). Make use of
that register instead of assuming a hardcoded value of 564 (since 564 is not
correct for devices that do QAM such as the KWorld 340u).
Note that for now the em2874 code isn't there, falling back to the 564 value,
however this is not a problem since there are not any em2874 based devices in
the current v4l-dvb tree).
Thanks to Jarod Wilson for detecting the initial problem and figuring out that
the isoc configuration was wrong for his device.
V4L/DVB (11808): au0828: get rid of debug printk that was causing compile failures
Remove a debug printk() line I added which is no longer needed, and happened
to be causing compile failures on some earlier kernels in Han's daily
compile report.
V4L/DVB (11807): cx88: remove xc5000 reset for Pinnacle 800i
According to the engineer at PCTV Systems, the xc5000 reset pin is supposed
to be on GPIO12. However, despite three nights of effort, pulling that GPIO
low didn't reset the xc5000. While pulling MO_SRST_IO low does reset the
xc5000, this also resets in the s5h1409 being reset as well. This causes
tuning to always fail since the internal state of the s5h1409 does not match
the driver's state.
Given that the only two conditions in which the driver performs a reset is
during firmware load and powering down the chip, I am taking out the reset.
We know that the chip is being reset when the cx88 comes online, and not being
able to do power management for this board is better than not having any
tuning at all.
Problem discovered when implementing proper power management for the xc5000,
which results in calls to the reset callback *after* s5h1409 is initialized.
V4L/DVB (11804): xc5000: poll at 5ms interval for register write command completion
Instead of polling at 100ms intervals for register writes, poll at 5ms
intervals. This is consistent with the xc5000 specification, and improves
tuning time by up to 500 ms on devices that such as the au0828 which do not
properly implement i2c clock stretching (since the five register writes that
occur for a tuning request often do not complete immediately but do complete
far before 100ms has gone by).
The net amount of time we wait before timing out is unchanged (500ms).
V4L/DVB (11802): xc5000: switch to new xc5000 firmware 1.6.114 with redistribution rights
Xceive has graciously allowed us to now freely redistribute the xc5000
firmware, which eliminates the need for users to manually extract the blob
from the Hauppauge driver.
Thanks to Brian Mathews <bmathews@xceive.com> for providing this code
V4L/DVB (11799): xc5000: don't load firmware until a tuning request is made
Defer loading of the xc5000 firmware until it is actually needed. This helps
on distros that have hald, which results in the device not being available
for use for around ten seconds in cases where the i2c bus is slow (such as
the HVR-950Q). Also, the firmware load isn't really useful since we
immediately put the device to sleep afterward, which means a firmware reload
will be required anyway.
Provide for the ability for a user to disable putting the tuner to sleep, in
case he doesn't want to incur the cost of reloading the firmware when starting
up his/her application. The module options are intentionally identical to
xc3028.
Make it a little more obvious in the dmesg output what is going on during
firmware upload. This is more important for boards like the HVR-950q that
take nearly seven seconds to do the upload.
V4L/DVB (11796): xc5000: start using the newer "finerfreq" tuning command
Starting in firmware version 1.1.44, Xceive recommends using the FINERFREQ for
all normal tuning (the doc indicates reg 0x03 should only be used for fast
scanning for channel lock)
V4L/DVB (11794): au0828: reduce reset time for xc5000 to 10ms
The xc5000 datasheet indicates that the reset pin only needs to be held low
for 10ms. Reduce the value accordingly, which speeds up the firmware load
time a bit.
V4L/DVB (11793): xc5000: Properly support power down for newer firmware
Xceive got rid of the XREG_POWER_DOWN register in later firmware revisions.
Their technical support informed me that the correct way to put the tuner
to sleep is to pull the reset pin (but don't reload the firmware).
V4L/DVB (11792): xc5000: switch to new version of Xceive firmware
This switches to a new version of the xc5000 firmware, extracted from the
latest Hauppauge driver. It includes the support for the XREG_BUSY register
(a lack of which was causing tuning to take 3200ms instead of around 300ms).
Bring back the code that puts the xc5000 to sleep. For the Pinnacle 801e
this results in power consumption at idle dropping from 325ma to 124ma.
If there are *actually* any devices that don't work in this configuration,
they should set dvb_frontend.ops.tuner_ops.sleep to NULL (per mkrufky's
suggestion)
Also, had to make sure we were making sure the firmware was loaded in the
digital version of set_params, or else we end up get i2c errors if the
device is asleep
Steven Toth [Sat, 2 May 2009 14:39:46 +0000 (11:39 -0300)]
V4L/DVB (11767): cx23885: Add preliminary support for the HVR1270
The patch means the board will be recognised, and the parts brought
out of reset correctly. This patches depends on the centralized GPIO
patch to be merged. What's missing before the HVR-1270 will function
for DTV? The model# needs to be added to avoid 'unknown model'
output and the LG3305/Tuner need to be attached in cx23885-dvb.c
Signed-off-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steven Toth [Sat, 2 May 2009 14:29:50 +0000 (11:29 -0300)]
V4L/DVB (11765): cx23885: Add generic functions for driving GPIO's
The GPIO's on the product can be in one of three places. To date we've
mainly used the GPIO's on the bridge itself, and once on the encoder.
Rather than having the complexity of multiple GPIO writes/reads from
isolated placed in the driver we'll route them through this function,
so we can make intelligent decisions about 1) Where the GPIO lives
and 2) Whether it conflicts (based on board) with some other function
to avoid bugs.
Signed-off-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Steven Toth [Tue, 5 May 2009 22:30:27 +0000 (19:30 -0300)]
V4L/DVB (11700): tda10048: Added option to block i2c gate control from other drivers.
Currently, DVB-T is broken and this fixes it.
The PVRUSB2 has an odd I2C bus configuration where opening the i2c gate
on the digital and analog demod causes the tuner to fail. This needs
to be protected against for the PVRUSB2.
Signed-off-by: Steven Toth <stoth@linuxtv.org> Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andy Walls [Sat, 9 May 2009 03:43:40 +0000 (00:43 -0300)]
V4L/DVB (11753): tveeprom: Point the TCL MNM05-4 tuner entry to an actual tuner definition
The TCL MNM05-04 is used on some HVR-1600 models. It appears to be
similar to the TCL MFMN05-4 but without FM radio. The
TUNER_PHILIPS_FM1236_MK3 tuner definition appears to be the proper existing
tuner definition to use for this tuner.
Reported-by: Matt Beadon <matt.beadon@gmail.com> Tested-by: Matt Beadon <matt.beadon@gmail.com> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Sat, 2 May 2009 03:22:27 +0000 (00:22 -0300)]
V4L/DVB (11748): pvrusb2: Don't use the internal i2c client list
The i2c core used to maintain a list of client for each adapter. This
is a duplication of what the driver core already does, so this list
will be removed as part of a future cleanup. Anyone using this list
must stop doing so.
For pvrusb2, I propose the following change, which should lead to an
equally informative output. The only difference is that i2c clients
which are not a v4l2 subdev won't show up, but I guess this case is
not supposed to happen anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 2 May 2009 03:04:35 +0000 (00:04 -0300)]
V4L/DVB (11747): pvrusb2: Bump up version advertised through v4l interface
Kick up the pvrusb2 version number advertised through the v4l
interface. This value really has almost no meaning because I don't
make a serious attempt to version the driver in this manner (otherwise
this one line becomes a nasty hotspot of changes and merge
conflicts). The value that is here is really a historical thing.
However Hans Verkuil thought it might be a good idea to bump up the
number anyway right now since the driver's mechanism for communicating
with the v4l core has pretty much completely changed. Sending out a
Mike Isely [Sat, 2 May 2009 01:33:16 +0000 (22:33 -0300)]
V4L/DVB (11746): pvrusb2: Set ir_video autoloading to default disabled
This sets the disable_autoload_ir_video module option to being set,
which disables any attempt by the driver to autoload IR support. This
changes preserves previous behavior, for now. This change can be set
back concurrent with other changes that finally update i2c-kbd-i2c to
use the new i2c binding model.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Sat, 2 May 2009 01:23:39 +0000 (22:23 -0300)]
V4L/DVB (11745): pvrusb2: Update to work with upcoming ir_video changes in v4l-dvb core
The ir-kbd-i2c module is about to be updated to match the new style
i2c binding model. These pvrusb2 changes maintain compatibility with
that change. Note that this does not actually break anything even
without the expected ir-kbd-i2c changes yet because previously the
pvrusb2 didn't autoload ir-kbd-i2c anyway.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mike Isely [Mon, 6 Apr 2009 04:51:38 +0000 (01:51 -0300)]
V4L/DVB (11744): pvrusb2: Select, track, and report IR scheme in use with the device
This change defines all possible "IR schemes" related to the pvrusb2
driver, on a per-device basis. That information is then set according
to the hardware in use. The idea here is to make possible a more
intelligent future decision on which, if any, IR receiver driver might
be loaded during initialization.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chaithrika U S [Thu, 7 May 2009 12:30:01 +0000 (09:30 -0300)]
V4L/DVB (11743): Analog Devices ADV7343 video encoder driver
Add ADV7343 I2C based video encoder driver. This follows the
v4l2-subdev framework. This driver has been tested on TI DM646x EVM. It
has been tested for Composite and Component outputs.
Updates as per review by Mauro Chehab, added support for more standards
supported by the encoder. Also adding the missed out signed-offs.Tested
only NTSC and PAL standards.
[hverkuil@xs4all.nl: s_routing API changed, updated driver to use new API] Signed-off-by: Manjunath Hadli <mrh@ti.com> Signed-off-by: Brijesh Jadav <brijesh.j@ti.com> Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Chaithrika U S [Thu, 7 May 2009 12:29:25 +0000 (09:29 -0300)]
V4L/DVB (11742): TI THS7303 video amplifier driver code
This patch adds driver for TI THS7303 video amplifier. This driver is
implemented as a v4l2 sub device. Tested on TI DM646x EVM.
This version has updates based on review comments by Mauro Chehab.
Signed-off-by: Chaithrika U S <chaithrika@ti.com> Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (11739): remove driver_data direct access of struct device
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Németh Márton [Wed, 29 Apr 2009 18:57:24 +0000 (15:57 -0300)]
V4L/DVB (11736): videobuf: modify return value of VIDIOC_REQBUFS ioctl
The V4L2 ioctls usually return 0 when the operation was successful
and -1 in case of error. Currently VIDIOC_REQBUFS returns the
number of buffers which is redundant because this information is
available in count field of struct v4l2_requestbuffers. The
V4L2 API specification, revision 0.24 [1] explicitly specifies for
VIDIOC_REQBUFS that the return value shall be 0 on success.
The patch was tested with v4l-test 0.13 [2] with vivi driver.
References:
[1] V4L2 API specification, revision 0.24
http://v4l2spec.bytesex.org/spec/r13696.htm
[2] v4l-test: Test environment for Video For Linux Two API
http://v4l-test.sourceforge.net/
Signed-off-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (11735): Enables the Winfast TV2000 XP Global TV IR
Adds support to the remote control of the Winfast TV2000 XP Global TV
capture card. A case statement was added in order to initialize the
GPIO data structures as well as a case statement for handling the keys
correctly when pressed.
Thanks to Hermann and Mauro for all the help
Signed-off-by: Pieter C van Schaik <vansterpc@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dmitri Belimov [Tue, 28 Apr 2009 09:46:15 +0000 (06:46 -0300)]
V4L/DVB (11734): remove hw reset of MPEG encoder when lost/found seq.
When we capture signal from composite input offen lost and found syncro
sequence. In this case the MPEG coder hardware reset after each
lost/found event. The image has a lot of artefactes. This patch remove
hardware reset of MPEG encoder.
Remove the videobuf-dma-contig sync operation. Sync is only needed
for noncoherent buffers, and since videobuf-dma-contig is built on
coherent memory allocators the memory is by definition always in sync.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com> Signed-off-by: Magnus Damm <damm@igel.co.jp> Reviewed-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean Delvare [Sun, 26 Apr 2009 08:43:59 +0000 (05:43 -0300)]
V4L/DVB (11723): Link firmware to physical device
Use the physical device rather than the i2c adapter as the reference
device when loading firmwares. This will prevent the sysfs name
collision with i2c-dev that has been reported many times.
I may have missed other drivers which need the same fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (11711): gspca - main: Fix a crash when no bandwidth available
When the bandwidth is not wide enough, the transfer endpoint may be set to
the one of the alternate setting 0. This one may be null and this causes a
divide by 0 oops.
Reported-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L/DVB (11705): soc-camera: prepare for the platform driver conversion
Add a platform driver to soc_camera.c. This way we preserve backwards
compatibility with existing platforms and can start converting them one by one
to the new platform-device soc-camera interface.
Andy Walls [Sun, 3 May 2009 21:01:57 +0000 (18:01 -0300)]
V4L/DVB (11703): cx18: Have audio decoder drive SIF gain control, and rework AFE config
Ensure the variable gain amplifier gain for SIF is driven by the audio deocder
and not the video decoder. This forced rework of the analog front end (AFE)
configuration to not rely on autoconfiguration, but instead set up the AFE mux,
AFE parameters, and ADC1 & ADC2 configurations explicitly.
Reported-by: Helen Buus <mythtv@hbuus.com> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
projects / linux-beck.git / log