Grant Grundler [Tue, 15 Nov 2011 07:12:42 +0000 (07:12 +0000)]
net-next:asix: V2 more fixes for ax88178 phy init sequence
Now works on Samsung Series 5 (chromebook)
Two fixes here:
o use 0x7F mask for phymode
o read phyid *AFTER* phy is powered up (via GPIOs)
Signed-off-by: Allan Chou <allan@asix.com.tw> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Grant Grundler [Tue, 15 Nov 2011 07:12:41 +0000 (07:12 +0000)]
net-next:asix: reduce AX88772 init time by about 2 seconds
ax88772_reset takes about 2 seconds and is called twice.
Once from ax88772_bind() directly and again indirectly from usbnet_open().
Reset the USB FW/Phy enough to blink the LEDs when inserted.
Signed-off-by: Allan Chou <allan@asix.com.tw> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Grant Grundler [Tue, 15 Nov 2011 07:12:40 +0000 (07:12 +0000)]
net-next:asix:poll in asix_get_phyid in case phy not ready
Sometimes the phy isn't ready after reset...poll and pray it will be soon.
Signed-off-by: Freddy Xin <freddy@asix.com.tw> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 15 Nov 2011 20:57:00 +0000 (12:57 -0800)]
sparc: Stash orig_i0 into %g6 instead of %g2
As per the comments added by this commit, %g2 turns out to not be a
usable place to save away orig_i0 for syscall restart handling.
In fact all of %g2, %g3, %g4, and %g5 are assumed to be saved across
a system call by various bits of code in glibc.
%g1 can't be used because that holds the syscall number, which would
need to be saved and restored for syscall restart handling too, and
that would only compound our problems :-)
This leaves us with %g6 and %g7 which are for "system use". %g7 is
used as the "thread register" by glibc, but %g6 is used as a compiler
and assembler temporary scratch register. And in no instance is %g6
used to hold a value across a system call.
Therefore %g6 is safe for storing away orig_i0, at least for now.
Signed-off-by: David S. Miller <davem@davemloft.net>
RS485: fix inconsistencies in the meaning of some variables
The crisv10.c and the atmel_serial.c serial drivers intepret the fields of the
serial_rs485 structure in a different way.
In particular, crisv10.c uses SER_RS485_RTS_AFTER_SEND and
SER_RS485_RTS_ON_SEND for the voltage of the RTS pin; atmel_serial.c,
instead, uses these values to know if a delay must be set before and
after sending. This patch makes the usage of these variables consistent
across all drivers and fixes the Documentation as well.
From now on, SER_RS485_RTS_AFTER_SEND and SER_RS485_RTS_ON_SEND will be
used to set the voltage of the RTS pin (as in the crisv10.c driver); the
delay will be understood by looking only at the value of
delay_rts_before_send and delay_rts_after_send.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com> Signed-off-by: Darron Black <darron@griffin.net> Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CAUSE:
Changing mode using setserial command, ".startup" function which gets DMA
channel is called before ".verify_port" function which sets
dma-flag(use_dma/use_dma_flag) as 1.
PIO->DMA
.startup: Since dma-flag is 0, DMA channel is not requested.
.verify_port: dma-flag is set as 1.
.shutdown: N/A
DMA->PIO
.startup: Since dma-flag is 1, DMA channel is requested.
.verify_port: dma-flag is set as 0.
.shutdown: Since dma-flag is 0, DMA channel is not released.
This means DMA channel resource leak occurs.
Next time, this driver can't get DMA channel resource forever.
MODIFICATION:
Currently, when release DMA channel resource, this driver checks dma-flag.
However, this specification occurs the above issue.
This driver must check whether dma_request_channel is executed or not.
The values are saved in private data variable "chan_tx/chan_tx".
These variables mean if the value is NULL, DMA channel is not requested,
if not NULL, DMA channel is requested.
Alan Cox [Thu, 10 Nov 2011 13:17:55 +0000 (13:17 +0000)]
serial,mfd: Fix CMSPAR setup
This is referenced the wrong way. Mika Westerberg added some checks to the
tty to support multiple console, but the real problem is simply referencing the
termios object via the wrong path.
Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doug Anderson [Wed, 12 Oct 2011 00:05:43 +0000 (17:05 -0700)]
tty/serial: Prevent drop of DCD on suspend for Tegra UARTs
On Tegra UARTs (except UART1), the DTR / DCD / DSR lines are not
externally accessible. Instead, the DTR line internally appears to be
looped back to be the input to the DCD and DSR lines. The net effect
of this is that when we drop DTR (like when we suspend), we'll see DCD
drop too. ...and when we see DCD drop, we treat that as a hangup.
In order to prevent this hangup from occurring at every sleep, we need
to force DTR to remain high on Tegra UARTs.
This patch uses the mcr_mask / mcr_force fields, which were originally
added for the kludge ALPHA_KLUDGE_MCR. Using these fields does not
prevent us from removing ALPHA_KLUDGE_MCR--we can just remove the "if"
tests I have added and always init mcr_mask / mcr_force from the
serial8250_config.
NOTE: If we have people that are using UARTA on a Tegra and need to
control DTR, we'll need to either add a separate port type for UARTA
or we'll need to add some tegra-specific code to detect whether the
DTR needs to be left high.
Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stephen Boyd [Wed, 26 Oct 2011 02:19:43 +0000 (19:19 -0700)]
tty: hvc_dcc: Fix duplicate character inputs
Reading from the DCC grabs a character from the buffer and
clears the status bit. Since this is a context-changing
operation, instructions following the character read that rely on
the status bit being accurate need to be synchronized with an
ISB.
In this case, the status bit check needs to execute after the
character read otherwise we run the risk of reading the character
and checking the status bit before the read can clear the status
bit in the first place. When this happens, the user will see the
same character they typed twice, instead of once.
Add an ISB after the read and the write, so that the status check
is synchronized with the read/write operations.
Fix warning of make xmldocs of documention of the struct member iommu_ops from struct bus_type.
Signed-off-by: Marcos Paulo de Souza <marcos.mage@gmail.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tomoya MORINAGA [Fri, 11 Nov 2011 01:12:18 +0000 (10:12 +0900)]
pch_phub: Fix MAC address writing issue for LAPIS ML7831
ISSUE:
Using ML7831, MAC address writing doesn't work well.
CAUSE:
ML7831 and EG20T have the same register map for MAC address access.
However, this driver processes the writing the same as ML7223.
This is not true.
This driver must process the writing the same as EG20T.
This patch fixes the issue.
Tomoya MORINAGA [Fri, 11 Nov 2011 01:12:17 +0000 (10:12 +0900)]
pch_phub: Improve ADE(Address Decode Enable) control
Currently, external ROM access is enabled/disabled in probe()/remove().
So, when a buggy software access unanticipated memory area,
in case of enabling this ADE bit,
external ROM memory area can be broken.
This patch enables the ADE bit only accessing external ROM area.
Felipe Balbi [Tue, 15 Nov 2011 07:23:26 +0000 (09:23 +0200)]
USB: storage: ene_ub6250: fix compile warnings
Fix the following compile warning:
| drivers/usb/storage/ene_ub6250.c: In function ‘ms_scsi_write’:
| drivers/usb/storage/ene_ub6250.c:1728:6: warning: ‘result’ may \
| be used uninitialized in this function [-Wuninitialized]
| drivers/usb/storage/ene_ub6250.c:1795:77: warning: ‘offset’ may \
| be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
wangyanqing [Thu, 10 Nov 2011 06:04:08 +0000 (14:04 +0800)]
USB: serial: pl2303: rm duplicate id
I get report from customer that his usb-serial
converter doesn't work well,it sometimes work,
but sometimes it doesn't.
The usb-serial converter's id:
vendor_id product_id
0x4348 0x5523
Then I search the usb-serial codes, and there are
two drivers announce support this device, pl2303
and ch341, commit 026dfaf1 cause it. Through many
times to test, ch341 works well with this device,
and pl2303 doesn't work quite often(it just work quite little).
ch341 works well with this device, so we doesn't
need pl2303 to support.I try to revert 026dfaf1 first,
but it failed. So I prepare this patch by hand to revert it.
Linus Torvalds [Tue, 15 Nov 2011 16:48:51 +0000 (14:48 -0200)]
Merge branch 'fixes' of git://git.linaro.org/people/triad/linux-pinctrl
* 'fixes' of git://git.linaro.org/people/triad/linux-pinctrl:
pinctrl: hide subsystem from the populace
pinctrl: fix "warning: 'struct pinctrl_dev' declared inside parameter list"
Linus Torvalds [Tue, 15 Nov 2011 16:45:50 +0000 (14:45 -0200)]
Merge branch 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio: pca953x: propagate the errno from the chip_init functions
gpio: pca953x: remove unneeded check for chip type
gpio/omap: check return value from irq_alloc_generic_chip
gpio/omap: replace MOD_REG_BIT macro with static inline
Linus Torvalds [Tue, 15 Nov 2011 16:31:12 +0000 (14:31 -0200)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
blackfin: Fixup export.h includes
Blackfin: add serial TX IRQ in individual platform resource
Jesper Juhl [Sun, 13 Nov 2011 21:14:32 +0000 (22:14 +0100)]
Net, libertas: Resolve memory leak in if_spi_host_to_card()
If we hit the default case in the switch in if_spi_host_to_card() we'll leak
the memory we allocated for 'packet'. This patch resolves the leak by freeing
the allocated memory in that case.
Signed-off-by: Jesper Juhl <jj@chaosbits.net> Acked-by: Dan Williams <dcbw@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00: Fix sleep-while-atomic bug in powersaving code.
The generic powersaving code that determines after reception of a frame
whether the device should go back to sleep or whether is could stay
awake was calling rt2x00lib_config directly from RX tasklet context.
On a number of the devices this call can actually sleep, due to having
to confirm that the sleeping commands have been executed successfully.
Fix this by moving the call to rt2x00lib_config to a workqueue call.
This fixes bug https://bugzilla.redhat.com/show_bug.cgi?id=731672
Tested-by: Tomas Trnka <tomastrnka@gmx.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Cc: <stable@vger.kernel.org> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Teika Kazura <teika@lavabit.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Tue, 15 Nov 2011 04:32:16 +0000 (20:32 -0800)]
sparc: Fix handling of orig_i0 wrt. debugging when restarting syscalls.
Although we provide a proper way for a debugger to control whether
syscall restart occurs, we run into problems because orig_i0 is not
saved and restored properly.
Luckily we can solve this problem without having to make debuggers
aware of the issue. Across system calls, several registers are
considered volatile and can be safely clobbered.
Therefore we use the pt_regs save area of one of those registers, %g2,
as a place to save and restore orig_i0.
Debuggers transparently will do the right thing because they save and
restore this register already.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Stern [Tue, 25 Oct 2011 14:50:58 +0000 (10:50 -0400)]
usb-storage: Accept 8020i-protocol commands longer than 12 bytes
The 8020i protocol (also 8070i and QIC-157) uses 12-byte commands;
shorter commands must be padded. Simon Detheridge reports that his
3-TB USB disk drive claims to use the 8020i protocol (which is
normally meant for ATAPI devices like CD drives), and because of its
large size, the disk drive requires the use of 16-byte commands.
However the usb_stor_pad12_command() routine in usb-storage always
sets the command length to 12, making the drive impossible to use.
Since the SFF-8020i specification allows for 16-byte commands in
future extensions, we may as well accept them. This patch (as1490)
changes usb_stor_pad12_command() to leave commands larger than 12
bytes alone rather than truncating them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Simon Detheridge <simon@widgit.com> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
these codes work in 32-bit, but in 64-bit, use u32 to type cast the address
of ioremap is not right, and accessing members of 'usb_sys_regs' will cause
call trace, so use (void *) for both 32-bit and 64-bit.
There's a race between the USB disconnect handler and the TTY close
handler which may cause the acm object to be freed while it's still
being used. This may lead to things like
This is the simplest fix I could come up with. Holding on to open_mutex
while closing the TTY device prevents acm_disconnect() from freeing the
acm object between acm->port.count drops to 0 and the TTY side of the
cleanups are finalized.
Thomas Poussevin [Thu, 27 Oct 2011 16:46:48 +0000 (18:46 +0200)]
USB: EHCI: fix HUB TT scheduling issue with iso transfer
The current TT scheduling doesn't allow to play and then record on a
full-speed device connected to a high speed hub.
The IN iso stream can only start on the first uframe (0-2 for a 165 us)
because of CSPLIT transactions.
For the OUT iso stream there no such restriction. uframe 0-5 are possible.
The idea of this patch is that the first uframe are precious (for IN TT iso
stream) and we should allocate the last uframes first if possible.
For that we reverse the order of uframe allocation (last uframe first).
Alan Stern [Thu, 3 Nov 2011 15:37:10 +0000 (11:37 -0400)]
USB: XHCI: resume root hubs when the controller resumes
This patch (as1494) fixes a problem in xhci-hcd's resume routine.
When the controller is runtime-resumed, this can only mean that one of
the two root hubs has made a wakeup request and therefore needs to be
resumed as well. Rather than try to determine which root hub requires
attention (which might be difficult in the case where a new
non-SuperSpeed device has been plugged in), the patch simply resumes
both root hubs.
Without this change, there is a race: The controller might be put back
to sleep before it can activate its IRQ line, and the wakeup condition
might never get handled.
The patch also simplifies the logic in xhci_resume a little, combining
some repeated flag settings into a single pair of statements.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@vger.kernel.org> Tested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 27 Oct 2011 15:20:21 +0000 (11:20 -0400)]
USB: workaround for bug in old version of GCC
This patch (as1491) works around a bug in GCC-3.4.6, which is still
supposed to be supported. The number of microseconds in the udelay()
call in quirk_usb_disable_ehci() is fixed at 100, but the compiler
doesn't understand this and generates a link-time error. So we
replace the otherwise unused variable "delta" with a simple constant
100. This same pattern is already used in other delay loops in that
source file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Konrad Rzepecki <krzepecki@dentonet.pl> Tested-by: Konrad Rzepecki <krzepecki@dentonet.pl> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bart Hartgers [Wed, 26 Oct 2011 11:29:42 +0000 (13:29 +0200)]
USB: ark3116 initialisation fix
This patch for the usb serial ark3116 driver fixes an initialisation
ordering bug that gets triggered on hotplug when using at least recent
debian/ubuntu userspace. Without it, ark3116 serial cables don't work.
Felipe Balbi [Thu, 10 Nov 2011 07:58:04 +0000 (09:58 +0200)]
usb: musb: fix compilation breakage introduced by de47725
commit de47725 (include: replace linux/module.h
with "struct module" wherever possible) introduced
a compilation breaked when it removed <linux/module.h>
from <linux/device.h> which musb glue layers were
(mistakenly) relying on.
Include that header to fix the compile error.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this the gadget will never be able to allocate a stream capable
endpoint. The manual says that the stream id is a 16bit id. It does not
talk about an upper limit in any other way. So I think 15 is a
reasonable limit :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / karo-tx-linux.git / log