If we take the "try_again" goto, due to a checksum error,
the 'len' has already been truncated. So we won't compute
the same values as the original code did.
Reported-by: paul bilke <fsmail@conspiracy.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'for-usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
* 'for-usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci:
Revert "xHCI: reset-on-resume quirk for NEC uPD720200"
xHCI: fix bug in xhci_clear_command_ring()
bridge: master device stuck in no-carrier state forever when in user-stp mode
When in user-stp mode, bridge master do not follow state of its slaves, so
after the following sequence of events it can stuck forever in no-carrier
state:
1) turn stp off
2) put all slaves down - master device will follow their state and also go in
no-carrier state
3) turn stp on with bridge-stp script returning 0 (go to the user-stp mode)
Now bridge master won't follow slaves' state and will never reach running
state.
This patch solves the problem by making user-stp and kernel-stp behavior
similar regarding master following slaves' states.
Signed-off-by: Vitalii Demianets <vitas@nppfactor.kiev.ua> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The commit added a reset-on-resume quirk because the NEC chipset stopped
responding to commands about 30 minutes after a system resume from
suspend. We thought it was a chipset issue, but it turns out that the
xHCI driver was zeroing out the link TRB after a successful context
restore during resume. The host controller would fall off the command
ring sometime later, causing it to not respond to new commands.
The link TRB issue has been fixed with commit 158886cd2cf4599e04f9b7e10cb767f5f39b14f1 "xHCI: fix bug in
xhci_clear_command_ring()", so revert the reset-on-resume quirk, as it's
not necessary.
Commit df711fc9962b9491af2b92bd0d21ecbfefe4e5fa was marked for stable
trees back to 2.6.37, but according to my mail, it has not made it into
Linus' tree or the stable trees yet.
Andiry Xu [Wed, 30 Nov 2011 08:37:41 +0000 (16:37 +0800)]
xHCI: fix bug in xhci_clear_command_ring()
When system enters suspend, xHCI driver clears command ring by writing zero
to all the TRBs. However, this also writes zero to the Link TRB, and the ring
is mangled. This may cause driver accesses wrong memory address and the
result is unpredicted.
When clear the command ring, keep the last Link TRB intact, only clear its
cycle bit. This should fix the "command ring full" issue reported by Oliver
Neukum.
This should be backported to stable kernels as old as 2.6.37, since the
commit 89821320 "xhci: Fix command ring replay after resume" is merged.
Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Reported-by: Oliver Neukum <oneukum@suse.de>
Linus Torvalds [Thu, 1 Dec 2011 16:28:53 +0000 (08:28 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix meta data raid-repair merge problem
Btrfs: skip allocation attempt from empty cluster
Btrfs: skip block groups without enough space for a cluster
Btrfs: start search for new cluster at the beginning
Btrfs: reset cluster's max_size when creating bitmap
Btrfs: initialize new bitmaps' list
Btrfs: fix oops when calling statfs on readonly device
Btrfs: Don't error on resizing FS to same size
Btrfs: fix deadlock on metadata reservation when evicting a inode
Fix URL of btrfs-progs git repository in docs
btrfs scrub: handle -ENOMEM from init_ipath()
Jan Schmidt [Thu, 1 Dec 2011 14:30:36 +0000 (09:30 -0500)]
Btrfs: fix meta data raid-repair merge problem
Commit 4a54c8c16 introduced raid-repair, killing the individual
readpage_io_failed_hook entries from inode.c and disk-io.c. Commit 4bb31e92 introduced new readahead code, adding a readpage_io_failed_hook to
disk-io.c.
The raid-repair commit had logic to disable raid-repair, if
readpage_io_failed_hook is set. Thus, the readahead commit effectively
disabled raid-repair for meta data.
This commit changes the logic to always attempt raid-repair when needed and
call the readpage_io_failed_hook in case raid-repair fails. This is much
more straight forward and should have been like that from the beginning.
Signed-off-by: Jan Schmidt <list.btrfs@jan-o-sch.net> Reported-by: Stefan Behrens <sbehrens@giantdisaster.de> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Charles Chin [Thu, 1 Dec 2011 10:21:00 +0000 (11:21 +0100)]
ALSA: hda - Fix S3/S4 problem on machines with VREF-pin mute-LED
The verb command in stac92xx_post_suspend caused the audio to stop
working after resuming from S3 mode on HP laptops with the VREF-pin
mute-LED control. Removing relevant post_suspend registering.
Although removing D3 on AFG is no optimal solution, the impact should
be small in comparison with the broken S3/S4.
Signed-off-by: Charles Chin <Charles.Chin@idt.com> Cc: <stable@kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Russell King [Sat, 5 Nov 2011 21:30:00 +0000 (21:30 +0000)]
ARM: restart: remove the now empty arch_reset()
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sat, 5 Nov 2011 12:36:40 +0000 (12:36 +0000)]
ARM: restart: remove comments about adding code to arch_reset()
arch_reset() is deprecated; systems should hook into system restart via
the 'restart' method in the platforms machine description record.
Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Jamie Iles <jamie@jamieiles.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 3 Nov 2011 09:53:29 +0000 (09:53 +0000)]
ARM: restart: at91: use new restart hook
Rather than using a private function pointer, use the existing
arm_pm_restart function pointer instead. We no longer need to enable
the I-cache in at91sam9_alt_reset() as the caches will now be on when
this function is called.
Update the function names to use the 'restart' terminology rather than
the 'reboot' terminology.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 3 Nov 2011 09:14:07 +0000 (09:14 +0000)]
ARM: restart: remove s3c24xx restart handler
Remove the s3c24xx restart handler, which is trying to work around
a chip bug by keeping caches on but flushed. As we now only disable
caches when performing a soft reboot, there doesn't need to be a
work-around to do that.
Acked-by: Kukjin Kim <kgene.kim@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
RongQing.Li [Thu, 1 Dec 2011 04:43:07 +0000 (23:43 -0500)]
net/core: fix rollback handler in register_netdevice_notifier
Within nested statements, the break statement terminates only the
do, for, switch, or while statement that immediately encloses it,
So replace the break with goto.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 30 Nov 2011 12:10:53 +0000 (12:10 +0000)]
sch_red: fix red_calc_qavg_from_idle_time
Since commit a4a710c4a7490587 (pkt_sched: Change PSCHED_SHIFT from 10 to
6) it seems RED/GRED are broken.
red_calc_qavg_from_idle_time() computes a delay in us units, but this
delay is now 16 times bigger than real delay, so the final qavg result
smaller than expected.
Use standard kernel time services since there is no need to obfuscate
them.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Only use the primary address of the bond device
for master_ip. This will prevent changing the ARP source
address in Active-Backup mode whenever a secondry address
is added to the bond device.
Signed-off-by: Henrik Saavedra Persson <henrik.e.persson@ericsson.com> Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@drr.davemloft.net>
Linus Torvalds [Thu, 1 Dec 2011 00:24:24 +0000 (16:24 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: twl: fix twl4030 support for smps regulators
regulator: fix use after free bug
regulator: aat2870: Fix the logic of checking if no id is matched in aat2870_get_regulator
ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below
The SWP instruction is deprecated on ARMv6 and with ARMv7 it will be
UNDEFINED when CONFIG_SWP_EMULATE is selected. In this case, probing a
SWP instruction will cause an oops when the kprobes emulation code
executes an undefined instruction.
As the SWP instruction should be rare or non-existent in kernels for
ARMv6 and later, we can simply avoid these problems by not allowing
probing of these.
Reported-by: Leif Lindholm <leif.lindholm@arm.com> Tested-by: Leif Lindholm <leif.lindholm@arm.com> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Jon Medhurst <tixy@yxit.co.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction
There is a kprobes testcase for the instruction "strd r2, [r3], r4".
This has unpredictable behaviour as it uses r3 for register writeback
addressing and also stores it to memory.
On a cortex A9, this testcase would fail because the instruction writes
the updated value of r3 to memory, whereas the kprobes emulation code
writes the original value.
Fix this by changing testcase to used r5 instead of r3.
Reported-by: Leif Lindholm <leif.lindholm@arm.com> Tested-by: Leif Lindholm <leif.lindholm@arm.com> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Signed-off-by: Jon Medhurst <tixy@yxit.co.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Dumazet [Tue, 29 Nov 2011 20:05:55 +0000 (20:05 +0000)]
ipv4: fix lockdep splat in rt_cache_seq_show
After commit f2c31e32b378 (fix NULL dereferences in check_peer_redir()),
dst_get_neighbour() should be guarded by rcu_read_lock() /
rcu_read_unlock() section.
Reported-by: Miles Lane <miles.lane@gmail.com> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Wunderlich [Wed, 30 Nov 2011 15:56:30 +0000 (16:56 +0100)]
mac80211: fill rate filter for internal scan requests
The rates bitmap for internal scan requests shoud be filled,
otherwise there will be probe requests with zero rates supported.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de> Cc: stable@vger.kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes' patch for "cfg80211: fix regulatory NULL dereference"
broke user regulaotry hints and it did not address the fact that
last_request was left populated even if the previous regulatory
hint was stale due to the wiphy disappearing.
Fix user reguluatory hints by only bailing out if for those
regulatory hints where a request_wiphy is expected. The stale last_request
considerations are addressed through the previous fixes on last_request
where we reset the last_request to a static world regdom request upon
reset_regdomains(). In this case though we further enhance the effect
by simply restoring reguluatory settings completely.
Cc: stable@vger.kernel.org Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211: fix race on init and driver registration
There is a theoretical race that if hit will trigger
a crash. The race is between when we issue the first
regulatory hint, regulatory_hint_core(), gets processed
by the workqueue and between when the first device
gets registered to the wireless core. This is not easy
to reproduce but it was easy to do so through the
regulatory simulator I have been working on. This
is a port of the fix I implemented there [1].
Cc: stable@vger.kernel.org Cc: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexandre Oliva [Wed, 30 Nov 2011 18:43:00 +0000 (13:43 -0500)]
Btrfs: skip block groups without enough space for a cluster
We test whether a block group has enough free space to hold the
requested block, but when we're doing clustered allocation, we can
save some cycles by testing whether it has enough room for the cluster
upfront, otherwise we end up attempting to set up a cluster and
failing. Only in the NO_EMPTY_SIZE loop do we attempt an unclustered
allocation, and by then we'll have zeroed the cluster size, so this
patch won't stop us from using the block group as a last resort.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Alexandre Oliva [Wed, 30 Nov 2011 18:43:00 +0000 (13:43 -0500)]
Btrfs: start search for new cluster at the beginning
Instead of starting at zero (offset is always zero), request a cluster
starting at search_start, that denotes the beginning of the current
block group.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Alexandre Oliva [Wed, 30 Nov 2011 18:43:00 +0000 (13:43 -0500)]
Btrfs: reset cluster's max_size when creating bitmap
The field that indicates the size of the largest contiguous chunk of
free space in the cluster is not initialized when setting up bitmaps,
it's only increased when we find a larger contiguous chunk. We end up
retaining a larger value than appropriate for highly-fragmented
clusters, which may cause pointless searches for large contiguous
groups, and even cause clusters that do not meet the density
requirements to be set up.
Signed-off-by: Alexandre Oliva <oliva@lsd.ic.unicamp.br> Signed-off-by: Chris Mason <chris.mason@oracle.com>
Alexandre Oliva [Mon, 28 Nov 2011 14:04:43 +0000 (12:04 -0200)]
Btrfs: initialize new bitmaps' list
We're failing to create clusters with bitmaps because
setup_cluster_no_bitmap checks that the list is empty before inserting
the bitmap entry in the list for setup_cluster_bitmap, but the list
field is only initialized when it is restored from the on-disk free
space cache, or when it is written out to disk.
Besides a potential race condition due to the multiple use of the list
field, filesystem performance severely degrades over time: as we use
up all non-bitmap free extents, the try-to-set-up-cluster dance is
done at every metadata block allocation. For every block group, we
fail to set up a cluster, and after failing on them all up to twice,
we fall back to the much slower unclustered allocation.
To make matters worse, before the unclustered allocation, we try to
create new block groups until we reach the 1% threshold, which
introduces additional bitmaps and thus block groups that we'll iterate
over at each metadata block request.
Mike Fleetwood [Fri, 18 Nov 2011 18:55:01 +0000 (18:55 +0000)]
Btrfs: Don't error on resizing FS to same size
It seems overly harsh to fail a resize of a btrfs file system to the
same size when a shrink or grow would succeed. User app GParted trips
over this error. Allow it by bypassing the shrink or grow operation.
Signed-off-by: Mike Fleetwood <mike.fleetwood@googlemail.com>
Miao Xie [Fri, 18 Nov 2011 09:43:00 +0000 (17:43 +0800)]
Btrfs: fix deadlock on metadata reservation when evicting a inode
When I ran the xfstests, I found the test tasks was blocked on meta-data
reservation.
By debugging, I found the reason of this bug:
start transaction
|
v
reserve meta-data space
|
v
flush delay allocation -> iput inode -> evict inode
^ |
| v
wait for delay allocation flush <- reserve meta-data space
And besides that, the flush on evicting inode will block the thread, which
is reclaiming the memory, and make oom happen easily.
Fix this bug by skipping the flush step when evicting inode.
Linus Torvalds [Tue, 29 Nov 2011 22:43:22 +0000 (14:43 -0800)]
Merge branch 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Update comments describing device power management callbacks
PM / Sleep: Update documentation related to system wakeup
PM / Runtime: Make documentation follow the new behavior of irq_safe
PM / Sleep: Correct inaccurate information in devices.txt
PM / Domains: Document how PM domains are used by the PM core
PM / Hibernate: Do not leak memory in error/test code paths
Paul Moore [Tue, 29 Nov 2011 10:10:54 +0000 (10:10 +0000)]
netlabel: Fix build problems when IPv6 is not enabled
A recent fix to the the NetLabel code caused build problem with
configurations that did not have IPv6 enabled; see below:
netlabel_kapi.c: In function 'netlbl_cfg_unlbl_map_add':
netlabel_kapi.c:165:4:
error: implicit declaration of function 'netlbl_af6list_add'
This patch fixes this problem by making the IPv6 specific code conditional
on the IPv6 configuration flags as we done in the rest of NetLabel and the
network stack as a whole. We have to move some variable declarations
around as a result so things may not be quite as pretty, but at least it
builds cleanly now.
Some additional IPv6 conditionals were added to the NetLabel code as well
for the sake of consistency.
Reported-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Paul Moore <pmoore@redhat.com> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / karo-tx-linux.git / log