ALSA: hda - Terminate the recursive connection search properly
The recursive search of widget connections in snd_hda_get_conn_index()
must be terminated at the pin and the audio-out widgets. Otherwise
you'll get "too deep connection" warnings unnecessarily.
Reported-by: Francis Moreau <francis.moro@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA: usb: refine delay information with USB frame counter
Existing code only updates the audio delay when URBs were
submitted/retired. This can introduce an uncertainty of 8ms
on the number of samples played out with the default settings,
and a lot more when URBs convey more packets to reduce the
interrupt rate and power consumption.
This patch relies on the USB frame counter to reduce the
uncertainty to less than 2ms worst-case. The delay information
essentially becomes independent of the URB size and number of
packets. This should help applications like PulseAudio which
require accurate audio timing. Clemens Ladisch reported
a decrease of mplayer's A-V difference from nrpacks down to at
most 1ms.
Thanks to Clemens for also pointing out that the implementation
of frame counters varies between different HCDs. Only the
8 lowest-bits are used to estimate the delay.
ASoC: ad193x: Setup regmap read and write flag masks for SPI
Currently register read-back for the ad193x is broken, because it expects bit 0
of the upper byte to be set to indicate a read operation, while the regmap
default for SPI is to use bit 7.
This patch also addresses another oddity of the device. There are SPI and I2C
versions of this codec. In both cases the registers are 8-bit wide and numbered
from 0x0 to 0x10, but in the SPI case there is also a so called
'global address' which is prefixed in-front of the register address. The global
address mimics I2C behaviour and includes a static device address the and the
read/write flag. This basically extends the register address to an 16-bit value
numbered from 0x800 to 0x810. These are the register numbers which are
currently used by the driver. This works, because I2C will ignore the upper
8 bits of the register, but it is still a bit confusing, as there are no such
register numbers in the I2C case.
The approach taken by this patch is to number the registers from 0x00 to 0x10
and encode the global address for SPI mode into the read and write flag masks.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Mon, 5 Sep 2011 18:46:32 +0000 (20:46 +0200)]
regmap: Provide device read and write map interface for merging
Add the externally visible interface introduced by Lars-Peter's commit
6f3064 (regmap: Add support for device specific write and read flag
masks) separately in order to allow merge into other subsystems for
integration with drivers. Drivers relying on this feature will not be
functional until they are merged with the implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lu Guanqun [Tue, 6 Sep 2011 07:21:43 +0000 (15:21 +0800)]
ASoC: sst_platform: fix memory leak
snd_pcm_hw_constraint_integer() could return -1, in this case, sst platform is
not opened successfully. However the corresponding close callback isn't able
to be called later on to release these two allocated memories, thus resulting
in memory leak.
This patch moves the check for hardware contraints earlier, thus resolving this
issue.
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com> Acked-by: Vinod Koul <vinod.koul@intel.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sun, 4 Sep 2011 16:35:47 +0000 (09:35 -0700)]
ASoC: Check that WM8996 FLL started even if we don't have the IRQ
We can directly read the FLL lock status on WM8996 so even if we don't
have an interrupt wired up we can still verify that the FLL started
successfully.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com>
Axel Lin [Fri, 2 Sep 2011 13:47:41 +0000 (21:47 +0800)]
ASoC: Add missing platform_device_put in raumfeld_audio_init error path
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Daniel Mack <zonque@gmail.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Sun, 4 Sep 2011 15:18:18 +0000 (08:18 -0700)]
ASoC: Fix reporting of partial jack updates
We need to report the entire jack state to the core jack code, not just
the bits that were being updated by the caller, otherwise the status
reported by other detection methods will be omitted from the state seen
by userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com> Cc: stable@kernel.org
Axel Lin [Sat, 3 Sep 2011 05:41:47 +0000 (13:41 +0800)]
ASoC: sn95031: Fix the logic to find free channel
In the case of no free channel available,
current implementation returns 0 instead of negative errno.
This patch fixes the logic to return -EINVAL if no free channel available.
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Vinod Koul <vinod.koul@linux.intel.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown [Wed, 24 Aug 2011 19:09:01 +0000 (20:09 +0100)]
ASoC: Allow source specification for CODEC level sysclk
Similarly to PLLs/FLLs some modern CODECs provide selectable system clock
sources. When the clock is the clock for a DAI we do not usually need to
identify which clock is being configured so can use clk_id for the source
clock but with CODEC wide system clocks we will need to specify both the
clock being configured and the source.
Add a source argument to the CODEC driver set_sysclk() operation to
reflect this. As this operation is not as widely used as the DAI
set_sysclk() operation the change is not very invasive. We probably
ought to go and make the same alternation for DAIs at some point.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fabio Estevam [Tue, 30 Aug 2011 03:28:42 +0000 (00:28 -0300)]
ASoC: imx: Fix build warning of unused 'card' variable
Fixes the following warning:
CC sound/soc/imx/imx-pcm-fiq.o
sound/soc/imx/imx-pcm-fiq.c: In function 'imx_pcm_fiq_new':
sound/soc/imx/imx-pcm-fiq.c:243: warning: unused variable 'card'
CC sound/soc/imx/imx-pcm-dma-mx2.o
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the condition for these WARN_ONs is reversed and they are placed
before the actual check whether we are going to write to that register. So if
the codec implements the register_writable callback we'll get a warning for each
writable register when syncing the register cache.
While we are at it change the check to use snd_soc_codec_writable_register
instead of open-coding it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC: snd_soc_codec_{readable,writable}_register change default to true
Change the default return value of snd_soc_codec_{readable,writable}_register to
true when no codec specific callback for this function is given. Otherwise all
registers of that codec will neither be readable nor writable, which is most
certainly not what we want.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Wolfram Sang [Thu, 25 Aug 2011 13:54:55 +0000 (15:54 +0200)]
ASoC: imx-ssi: use dma_writecombine consistently
If the channel is allocated as writecombine, then mmaping it should also
use writecombine. Also, add a proper device for the call. Ported from a
similar fix for mach-mxs.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
susan gao [Fri, 26 Aug 2011 19:14:14 +0000 (12:14 -0700)]
ASoC: Add 3D stereo support for wm8996
My first patch to ASoC ever! If I did something wrong, blame Ian.
Signed-off-by: Susan Gao <sgao@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ben Gardiner [Fri, 26 Aug 2011 16:02:44 +0000 (12:02 -0400)]
ASoC: davinci-mcasp: add support for unsigned PCM formats
Although the McASP supports sign-extending samples in RX or TX [1]; the
davinci-mcasp driver does not touch the {R,X}PBIT or {R,X}PAD field of the
{R,X}FMT registers meaning that the McASP will serialize the bytes it is given
regardless of their signedness. So supporting unsigned formats is as simple
as adding them to the metadata of the davinci-mcasp driver.
Update the FMTBITs reported in the snd_soc_dai_driver and also update the case
statements in davinci-mcasp's hw_params() function so that the McASP can be
connected to CODECs that use unsigned values.
[1] http://www.ti.com/lit/ug/sprufm1/sprufm1.pdf
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALSA: hda: Conexant: Allow different output types to share DAC
Headphones has stopped working for the original reported (a regression
compared to 2.6.38). This is because Speaker and Headphones share the
same DAC, in which case no Headphones volume control was created.
This patch fixes so that both Speaker and Headphones volume
controls are created in such scenario.
BugLink: http://bugs.launchpad.net/bugs/817943 Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Timur Tabi [Tue, 23 Aug 2011 21:48:26 +0000 (16:48 -0500)]
ASoC: MPC5200: replace of_device with platform_device
'struct of_device' no longer exists, and its functionality has been merged
into platform_device. Update the MPC5200 audio DMA driver (mpc5200_dma)
accordingly. This fixes a build break.
Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
Takashi Iwai [Wed, 24 Aug 2011 15:57:44 +0000 (17:57 +0200)]
ALSA: hda - Prefer multi-io to speakers for realtek auto-parser
When the multi-io jacks are available, parse them first and assign DACs
before parsing speakers and headphones. This allows a better chance of
surround I/O in some desktops and laptops with limited DACs.
Takashi Iwai [Wed, 24 Aug 2011 15:27:52 +0000 (17:27 +0200)]
ALSA: hda - Fix Center/LFE mixer element creations for Realtek
The commit 23c09b00900c3fa6672148738cad29d6fc6ded7c
ALSA: hda - Support multiple speakers by Realtek auto-parser
changes the return value from alc_get_line_out_pfx(), and it breaks
the center/LFE mixer split check. The caller must test with a string
"CLFE" now.
Takashi Iwai [Wed, 24 Aug 2011 14:22:21 +0000 (16:22 +0200)]
ALSA: hda - Rewrite Lenovo X200 quirk with pincfg-fix using auto-parser
Introduce the pincfg table to patch_conexant.c for fixing up the extra
pin-configuration for auto-parser. As an example, Lenovo X200 model is
replaced with this new mechanism. (This also fixes the wrong mixer
elements for docking-station I/O in the previous model quirk
automagically.)
Stephen Warren [Tue, 23 Aug 2011 17:16:28 +0000 (11:16 -0600)]
ASoC: Tegra: wm8903 machine driver: Drop Ventana support
Board file support for Ventana is not yet mainlined, and probably won't
ever be given the move to Device-Tree. Consequently, the Ventana entry
is being removed from arch/arm/tools/mach-types in the next merge window,
since it was registered over a year ago.
This will also remove function machine_is_ventana(), which is used by
the ASoC Tegra WM8903 machine driver. This will cause compilation
failures. Drop Ventana support to resolve this.
Hopefully, in the not-too-distant future, tegra_wm8903.c will be able to
configure itself from Device-Tree, and hence we'll be able to re-instate
Ventana support just by creating a .dts file for the board.
Also note that Aebl support is in a similar boat. However, that board
isn't scheduled for deprecation for at least another 5 months, and
perhaps we will have completely removed non-Device-Tree support from
tegra_wm8903.c by then and/or adjusted mach-types policy.
Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Joseph Pentland [Tue, 23 Aug 2011 09:41:50 +0000 (10:41 +0100)]
ASoC: Add Springbank I/O card to Speyside Kconfig
Signed-off-by: Joseph Pentland <jp@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are references in the code to 256 sources, so I tested it with 256 aplays,
of which the first and last with real data and the rest playing /dev/zero .
Also increase amount of page tables, so the default aplay size works.
Lu Guanqun [Wed, 24 Aug 2011 06:45:10 +0000 (14:45 +0800)]
ALSA: core: release the constraint check for replace ops
Suppose the ALSA card already has a number of MAX_USER_CONTROLS controls, and
the user wants to replace one, it should not fail at this condition check.
Signed-off-by: Lu Guanqun <guanqun.lu@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Tue, 23 Aug 2011 16:27:14 +0000 (18:27 +0200)]
ALSA: hda - Rewrite ALC662 asus-mode* models with fixups
Re-implement the asus-mode[1-8] quirks with the pin-config tables.
They are provided in case where BIOS is broken on the device, so it's
not enabled in PCI SSID lookup table. User needs to specify it via model
option explicitly if the driver doesn't work with the BIOS setup as is.
Takashi Iwai [Tue, 23 Aug 2011 16:16:13 +0000 (18:16 +0200)]
ALSA: hda - Add multi-headphone NIDs in multiout struct
For supporting both the multiple headphones and the multiple speakers,
add the new field in struct hda_multi_out, and evaluate in the standard
setup functions.
Takashi Iwai [Tue, 23 Aug 2011 15:28:55 +0000 (17:28 +0200)]
ALSA: hda - Restore VREF50 setup for ALC861-VD dallas/hp models
During the cleanup by commit 6727b12669f255dbf65b3d63c32cce1e3e967398,
the specific setups for dallas and hp models, using VREF50 for mic pins,
were lost. Fixed now.
Takashi Iwai [Tue, 23 Aug 2011 12:57:08 +0000 (14:57 +0200)]
ALSA: hda - Fix double-headphone/speaker paths for Cxt auto-parser
When multiple headphones or speakers are assigned but no individual
DACs are available, the driver should take the first HP/SPK DAC instead
of another primary output. The patch adds a bit-flag to dac field of
struct pin_dac_pair indicating that it's a slave DAC.
Takashi Iwai [Tue, 23 Aug 2011 10:41:09 +0000 (12:41 +0200)]
ALSA: hda - Update jack-sense info even when no automute is set
The internal states, jack_present and line_jack_present should be
updated upon unsolicited events even if no automute is set.
Otherwise the wrong state is referred when the automute behavior is
changed by the mixer control.
Takashi Iwai [Tue, 23 Aug 2011 10:36:28 +0000 (12:36 +0200)]
ALSA: hda - Fix output-path initialization for Realtek auto-parser
When the headphone or speaker output has no own DAC, initialize the path
using the primary DAC. Otherwise the path won't be set properly and
can result in the silence.
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Dong Aisheng <b29396@freescale.com> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dong Aisheng [Sun, 21 Aug 2011 15:45:40 +0000 (23:45 +0800)]
ASoC: mxs-saif: clear clk gate first before register setting
Saif needs clear clk gate first before writing registers or the write
will not success.
The original xx_get_mclk function clear clk gate after mclk setting
that may cause the former mclk setting unwork, then the real output
mclk maybe inaccurate.
Placing the clear before setting mclk to avoid such an issue.
We also have to clear clk gate in startup instead of in prepare function.
Signed-off-by: Dong Aisheng <b29396@freescale.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The first change is to add an of_node_put, since codec_np has previously
been allocated. The rest of the patch reorganizes the error handling code
so the only code executed is that which is needed.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
(
if (...) { ... when != of_node_put(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
of_node_put(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Timur Tabi <timur@freescale.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
(
if (...) { ... when != of_node_put(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
of_node_put(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
(
if (...) { ... when != kfree(x)
when != x = E3
when != E3 = x
* return ...;
}
... when != x = E2
when != I(...,x,...) S
if (...) { ... when != x = E4
kfree(x); ... return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Alexander Sverdlin <subaparts@yandex.ru> Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: Liam Girdwood <lrg@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>