Andreas Bießmann [Fri, 31 Aug 2012 11:35:42 +0000 (13:35 +0200)]
mtd: omap2: fix module loading
Unloading the omap2 nand driver missed to release the memory region which will
result in not being able to request it again if one want to load the driver
later on.
This patch fixes following error when loading omap2 module after unloading:
---8<---
~ $ rmmod omap2
~ $ modprobe omap2
[ 37.420928] omap2-nand: probe of omap2-nand.0 failed with error -16
~ $
--->8---
Andreas Bießmann [Fri, 31 Aug 2012 11:35:41 +0000 (13:35 +0200)]
mtd: omap2: fix omap_nand_remove segfault
Do not kfree() the mtd_info; it is handled in the mtd subsystem and
already freed by nand_release(). Instead kfree() the struct
omap_nand_info allocated in omap_nand_probe which was not freed before.
This patch fixes following error when unloading the omap2 module:
Stefan Roese [Tue, 28 Aug 2012 09:34:13 +0000 (11:34 +0200)]
mtd: cfi_cmdset_0001: Fix problem with unlocking timeout
Unlocking may take up to 1.4 seconds on some Intel flashes. So
lets use a max. of 1.5 seconds (1500ms) as timeout.
See "Clear Block Lock-Bits Time" on page 40 in
"3 Volt Intel StrataFlash Memory" 28F128J3,28F640J3,28F320J3 manual
from February 2003
This patch also fixes some other problems with this timeout:
- Don't use HZ in timeout "calculation"!
While testing we noticed that an unlocking timeout occured with
HZ=1000 and didn't occur with HZ=300. This was because the
timeout parameter was calculated differently depending on the
HZ value. Now a fixed value of 1500ms is used.
- The last parameter of WAIT_TIMEOUT (defined to
inval_cache_and_wait_for_operation) has to be passed in
micro-seconds. So multiply the ms value with 1000 and not 100
to calculate this value.
- Use variable name "mdelay" instead of misleading "udelay".
Signed-off-by: Stefan Roese <sr@denx.de> Tested-by: Stephan Gatzka <stephan@gatzka.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Jeff Westfahl [Mon, 13 Aug 2012 21:35:30 +0000 (16:35 -0500)]
mtd: nand: Added a device flag for subpage read support
Added a NAND device flag for subpage read support. Previously this was
hard coded based on large page and soft ECC.
Updated base NAND driver to use the new subpage read flag if the NAND is
large page and soft ECC.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com> Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Thomas Petazzoni [Mon, 27 Aug 2012 23:35:28 +0000 (01:35 +0200)]
mtd: orion_nand: remove <mach/hardware.h> include
Commit abcda1dc ('arm: plat-orion: introduce PLAT_ORION_LEGACY hidden
config option') currently pending in linux-next will make the ARCH_MVEBU
platform select PLAT_ORION, which means that now all Orion drivers can
be enabled on ARCH_MVEBU. This works fine for most drivers, except for
orion_nand, because it includes <mach/hardware.h>, but mach-mvebu does
not have a mach/hardware.h header (it is considered as a deprecated
practice).
It turns out that the <mach/hardware.h> include in orion_nand is not
necessary: the driver builds perfectly fine without it, so we simply
get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Roland Stigge [Fri, 24 Aug 2012 13:06:52 +0000 (15:06 +0200)]
mtd: lpc32xx_mlc: Cleanup after DT-only conversion
The LPC32xx's DT-only conversion of the MLC NAND driver makes NAND config via
platform_data obsolete. Dropped by this patch.
Further, the driver really needs CONFIG_OF, which is already reflected by the
dependency on ARCH_LPC32XX which depends on CONFIG_OF. So also dropping
CONFIG_OF ifdefs.
There is still platform_data necessary to supply the dma_filter callback for
the dma engine. This is a completely different data structure than the old
platform_data for NAND config, so renaming some old "pdata" variable to "ncfg"
to prevent confusion with the new platform data.
Signed-off-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Roland Stigge [Fri, 24 Aug 2012 13:06:51 +0000 (15:06 +0200)]
mtd: lpc32xx_slc: Cleanup after DT-only conversion
The LPC32xx's DT-only conversion of the SLC NAND driver makes NAND config via
platform_data obsolete. Dropped by this patch.
Further, the driver really needs CONFIG_OF, which is already reflected by the
dependency on ARCH_LPC32XX which depends on CONFIG_OF. So also dropping
CONFIG_OF ifdefs.
There is still platform_data necessary to supply the dma_filter callback for
the dma engine. This is a completely different data structure than the old
platform_data for NAND config, so renaming some old "pdata" variable to "ncfg"
to prevent confusion with the new platform data.
Signed-off-by: Roland Stigge <stigge@antcom.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Shmulik Ladkani [Mon, 20 Aug 2012 13:29:15 +0000 (16:29 +0300)]
mtd: nand: rename create_bbt()'s 'len' variable to 'numpages'
Rename 'len' variable of create_bbt/scan_block_fast/scan_block_full to
'numpages', since it really means number of pages to scan when
searching for the BBM (and not the byte length of the scan).
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Sachin Kamat [Tue, 21 Aug 2012 08:54:10 +0000 (14:24 +0530)]
mtd: s3c2410: Fix compiler warnings
Fixes the following warnings:
‘s3c2410_nand_correct_data’ defined but not used [-Wunused-function]
‘s3c2410_nand_enable_hwecc’ defined but not used [-Wunused-function]
‘s3c2412_nand_enable_hwecc’ defined but not used [-Wunused-function]
‘s3c2440_nand_enable_hwecc’ defined but not used [-Wunused-function]
‘s3c2410_nand_calculate_ecc’ defined but not used [-Wunused-function]
‘s3c2412_nand_calculate_ecc’ defined but not used [-Wunused-function]
‘s3c2440_nand_calculate_ecc’ defined but not used [-Wunused-function]
The above functions are called only when CONFIG_MTD_NAND_S3C2410_HWECC
is defined. Thus making them conditional.
Sachin Kamat [Tue, 21 Aug 2012 08:54:09 +0000 (14:24 +0530)]
mtd: s3c2410: Use devm_* functions
devm_* functions are device managed functions and make cleanup code
simpler and smaller.
devm_kzalloc, devm_clk_get and devm_request_and_ioremap functions
are used.
Huang Shijie [Sat, 18 Aug 2012 17:07:41 +0000 (13:07 -0400)]
mtd: mtdpart: break it as soon as we parse out the partitions
We may cause a memory leak when the @types has more then one parser.
Take the `default_mtd_part_types` for example. The default_mtd_part_types has
two parsers now: `cmdlinepart` and `ofpart`.
Assume the following case:
The kernel command line sets the partitions like:
#gpmi-nand:20m(boot),20m(kernel),1g(rootfs),-(user)
But the devicetree file(such as arch/arm/boot/dts/imx28-evk.dts) also sets
the same partitions as the kernel command line does.
In the current code, the partitions parsed out by the `ofpart` will
overwrite the @pparts which has already set by the `cmdlinepart` parser,
and the the partitions parsed out by the `cmdlinepart` is missed.
A memory leak occurs.
So we should break the code as soon as we parse out the partitions,
In actually, this patch makes a priority order between the parsers.
If one parser has already parsed out the partitions successfully,
it's no need to use another parser anymore.
On some platforms (e.g. MPC5200) a direct 1:1 mapping may cause
problems with JFFS2 usage, as the local bus (LPB) doesn't support
unaligned accesses as implemented in the JFFS2 code via memcpy().
By defining "no-unaligned-direct-access", the flash will not be
exposed directly to the MTD users (e.g. JFFS2) any more.
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Julia Lawall [Sat, 4 Aug 2012 20:36:38 +0000 (22:36 +0200)]
mtd: spear_smi: use devm_ functions consistently
Use devm_kzalloc for all calls to kzalloc and not just the first. Use devm
functions for other allocations as well.
Move the call to platform_get_resource(pdev, IORESOURCE_MEM, 0) closer to
where its result is passed to devm_request_and_ioremap to make the lack of
need for a NULL test more evident.
The semantic match that finds the inconsistency is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
*devm_kzalloc(...)
...
*kzalloc(...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
John Crispin [Thu, 23 Aug 2012 18:28:32 +0000 (20:28 +0200)]
mtd: lantiq: Add NAND support on Lantiq XWAY SoC.
The driver uses plat_nand. As the platform_device is loaded from DT, we need
to lookup the node and attach our xway specific "struct platform_nand_data"
to it.
Signed-off-by: John Crispin <blogic@openwrt.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Huang Shijie [Wed, 15 Aug 2012 02:38:45 +0000 (22:38 -0400)]
mtd: kill MTD_NAND_VERIFY_WRITE
Just as Artem suggested:
"Both UBI and JFFS2 are able to read verify what they wrote already.
There are also MTD tests which do this verification. So I think there
is no reason to keep this in the NAND layer, let alone wasting RAM in
the driver to support this feature. Besides, it does not work for sub-pages
and many drivers have it broken. It hurts more than it provides benefits."
Wolfram Sang [Sat, 11 Aug 2012 08:58:43 +0000 (10:58 +0200)]
mtd: maps: pci: remove dead code
Removes disabled printk (which should be dev_dbg these days) as well
as #if 0 blocks (which are trivial to reimplement if ever needed) to
meet basic CodingStyle guidelines.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Artem Bityutskiy [Thu, 23 Aug 2012 07:10:07 +0000 (10:10 +0300)]
JFFS2: fix unmount regression
This patch fixes regression introduced by
"8bdc81c jffs2: get rid of jffs2_sync_super". We submit a delayed work in order
to make sure the write-buffer is synchronized at some point. But we do not
flush it when we unmount, which causes an oops when we unmount the file-system
and then the delayed work is executed.
This patch fixes the issue by adding a "cancel_delayed_work_sync()" infocation
in the '->sync_fs()' handler. This will make sure the delayed work is canceled
on sync, unmount and re-mount. And because VFS always callse 'sync_fs()' before
unmounting or remounting, this fixes the issue.
mtd: allow uclinux map driver to be used on any ColdFire CPU platform
The uclinux.c map driver has traditionally been used only on non-MMU based
systems. But there is no fundamental reason it can't be used on systems
running with virtual memory.
Some ColdFire CPU based systems now have full paged MMU hardware and can use
the uclinux.c mapping driver, so making the uclinux.c driver configuration
depend on !CONFIG_MMU doesn't make sense now. Allow the CONFIG_MTD_UCLINUX
option to be enabled if CONFIG_COLDFIRE is enabled. (I have chosen not to
just more generally allow uclinux.c for any MMU type to keep this option
hidden for most systems that are not interested in setting it).
mtd: fix wrong usage of ioremap_nocache() in uclinux.c map driver
The uclinux.c mapping driver uses ioremap_nocache() to map its physical
mapping address to a system virtual address. Problem is that the region
it is mapping is not device memory. It is ordinary system RAM. On most
non-MMU systems this doesn't matter, and the mapping is always a 1:1
translation of the address. On paged memory systems on some architectures
the page table mappings are not compatible between normal RAM and device
memory.
If we want to use the uclinux.c mapping driver on real MMU enabled systems
we should be using the kernel virtual address that the mapping is at. For
architectures that support the traditional initrd they use phys_to_virt or
__va to convert the physical start initrd address to a kernel usable virtual
address. The uclinux filesystem mapping is even more restrictive than the
typical initrd, it always follows the kernels own bss section (so always in
directly mapped memory). Therefore we can use the usual phys_to_virt to
translate the physical start address to a virtual address.
Alexander Shiyan [Wed, 15 Aug 2012 16:28:06 +0000 (20:28 +0400)]
mtd: autcpu12-nvram: Convert driver to platform_device
Because we can have a single kernel to support multiple machines, we
need to make loading specific drivers for the target platform only.
For this, driver is converted to the platform driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Alexander Shiyan [Wed, 15 Aug 2012 16:28:05 +0000 (20:28 +0400)]
mtd: autcpu12-nvram: Fix compile breakage
Update driver autcpu12-nvram.c so it compiles; map_read32/map_write32
no longer exist in the kernel so the driver is totally broken.
Additionally, map_info name passed to simple_map_init is incorrect.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Arnd Bergmann <arnd@arndb.de> Cc: stable@vger.kernel.org Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Fri, 13 Jul 2012 16:28:24 +0000 (09:28 -0700)]
mtd: nand: allow NAND_NO_SUBPAGE_WRITE to be set from driver
The NAND_CHIPOPTIONS_MSK has limited utility and is causing real bugs. It
silently masks off at least one flag that might be set by the driver
(NAND_NO_SUBPAGE_WRITE). This breaks the GPMI NAND driver and possibly
others.
Really, as long as driver writers exercise a small amount of care with
NAND_* options, this mask is not necessary at all; it was only here to
prevent certain options from accidentally being set by the driver. But the
original thought turns out to be a bad idea occasionally. Thus, kill it.
Note, this patch fixes some major gpmi-nand breakage.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Tested-by: Huang Shijie <shijie8@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mike Dunn [Wed, 11 Jul 2012 18:08:19 +0000 (11:08 -0700)]
mtd: docg4: fix oob reads
This patch does two closely related things:
(1) Currently the ecc.read_page() method does not fill the nand->oob_poi buffer
with the oob data, but instead reads oob into a local buffer. Fix this by
filling the oob_poi buffer instead of a local buffer. The 'oob_required'
argument is quietly ignored; the device must always read oob after the page
data, and it is presumed that there's no harm in filling oob_poi, even when not
explicitly requested.
(2) Always read oob from the device in ecc.read_oob(), instead of copying it
from a local buffer under some circumstances.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Artem Bityutskiy [Fri, 17 Aug 2012 10:05:41 +0000 (13:05 +0300)]
mtd: spear_smi: fix compilation warning
drivers/mtd/devices/spear_smi.c: In function 'spear_smi_probe':
drivers/mtd/devices/spear_smi.c:984:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Fri, 22 Jun 2012 23:35:42 +0000 (16:35 -0700)]
mtd: nand: rename '_raw' BBT scan functions
None of these scanning functions use MTD_OPS_RAW mode any more, so there's
really nothing 'raw' about them. Rename them to (hopefully) make the code
a little clearer.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Fri, 22 Jun 2012 23:35:45 +0000 (16:35 -0700)]
mtd: nand: use ECC, if present, when scanning OOB
scan_read_raw_oob() is used in only in places where the MTD_OPS_PLACE_OOB mode
is preferable to MTD_OPS_RAW mode, so use MTD_OPS_PLACE_OOB instead.
MTD_OPS_PLACE_OOB provides the same functionality with the potential[1] added
bonus of error correction.
This brings scan_block_full() in line with scan_block_fast() so that they
both read bad block markers with MTD_OPS_PLACE_OOB. This can help in
preventing 0xff markers (in good blocks) from being interpreted as bad
block indicators in the presence of a single bitflip.
Note that ECC error codes (EUCLEAN or EBADMSG) are already silently
ignored in all users of scan_read_raw_oob().
[1] Few drivers perform proper error correction on OOB data. In those
cases, the use of MTD_OPS_RAW vs. MTD_OPS_PLACE_OOB is not
significant.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Brian Norris [Fri, 22 Jun 2012 23:35:39 +0000 (16:35 -0700)]
mtd: check for max_bitflips in mtd_read_oob()
mtd_read_oob() has some unexpected similarities to mtd_read(). For
instance, when ops->datbuf != NULL, nand_base.c might return max_bitflips;
however, when ops->datbuf == NULL, nand_base's code potentially could
return -EUCLEAN (no in-tree drivers do this yet). In any case where the
driver might return max_bitflips, we should translate this into an
appropriate return code using the bitflip_threshold.
Essentially, mtd_read_oob() duplicates the logic from mtd_read().
This prevents users of mtd_read_oob() from receiving a positive return
value (i.e., from max_bitflips) and interpreting it as an unknown error.
Artem: amend comments.
Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Mike Dunn <mikedunn@newsguy.com> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The gpmi nand driver may needs several clocks(MX6Q needs five clocks).
In the old clock framework, all these clocks are chained together,
all you need is to manipulate the first clock.
But the kernel uses the common clk framework now, which forces us to
get the clocks one by one. When we use them, we have to enable them
one by one too.
Ian Kent [Mon, 6 Aug 2012 01:37:47 +0000 (09:37 +0800)]
autofs4 - fix get_next_positive_subdir()
Following a report of a crash during an automount expire I found that
the locking in fs/autofs4/expire.c:get_next_positive_subdir() was wrong.
Not only is the locking wrong but the function is more complex than it
needs to be.
The function is meant to calculate (and dget) the next entry in the list
of directories contained in the root of an autofs mount point (an autofs
indirect mount to be precise). The main problem was that the d_lock of
the owner of the list was not being taken when walking the list, which
lead to list corruption under load. The only other lock that needs to
be taken is against the next dentry candidate so it can be checked for
usability.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 16 Aug 2012 18:47:42 +0000 (11:47 -0700)]
Merge tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO fix from Alex Williamson:
"Just a trivial patch to include vfio.h in the installed headers so we
can complete userspace integration into QEMU."
* tag 'vfio-for-v3.6-rc1' of git://github.com/awilliam/linux-vfio:
vfio: Include vfio.h in installed headers
Linus Torvalds [Thu, 16 Aug 2012 18:31:59 +0000 (11:31 -0700)]
Merge tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fix from Konrad Rzeszutek Wilk:
"Way back in v3.5 we added a mechanism to populate back pages that were
released (they overlapped with MMIO regions), but neglected to reserve
the proper amount of virtual space for extend_brk to work properly.
Coincidentally some other commit aligned the _brk space to larger area
so I didn't trigger this until it was run on a machine with more than
2GB of MMIO space."
* On machines with large MMIO/PCI E820 spaces we fail to boot b/c
we failed to pre-allocate large enough virtual space for extend_brk.
* tag 'stable/for-linus-3.6-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m: Reserve 8MB of _brk space for P2M leafs when populating back.
Linus Torvalds [Thu, 16 Aug 2012 18:13:16 +0000 (11:13 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull two slave-dmaengine fixes from Vinod Koul:
"One fixes the correct use of clock API in imx driver and the other
enables clock for tegra driver, which is used for other tegra driver
conversion to dmanegine in -next."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: enable/disable dma clock
dma: imx-dma: Fix kernel crash due to missing clock conversion
Linus Torvalds [Thu, 16 Aug 2012 18:08:32 +0000 (11:08 -0700)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull more drm fixes from Dave Airlie:
"Just some intel and nouveau ones this time, intel has more edp panel
fixes for macbooks and nouveau has a suspend/resume regression fix in
there."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
drm/nve0/fifo: add support for the flip completion swmthd
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Be less verbose during vmemmap population.
sparc64: do not clobber personality flags in sys_sparc64_personality()
Dave Airlie [Wed, 15 Aug 2012 10:31:22 +0000 (20:31 +1000)]
Merge branch 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/nve0/fifo: add support for the flip completion swmthd
Dave Airlie [Wed, 15 Aug 2012 10:27:51 +0000 (20:27 +1000)]
Merge branch 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel Vetter writes:
"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a
Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power). It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
David S. Miller [Wed, 15 Aug 2012 07:37:29 +0000 (00:37 -0700)]
sparc64: Be less verbose during vmemmap population.
On a 2-node machine with 256GB of ram we get 512 lines of
console output, which is just too much.
This mimicks Yinghai Lu's x86 commit c2b91e2eec9678dbda274e906cc32ea8f711da3b
(x86_64/mm: check and print vmemmap allocation continuous) except that
we aren't ever going to get contiguous block pointers in between calls
so just print when the virtual address or node changes.
This decreases the output by an order of 16.
Also demote this to KERN_DEBUG.
Signed-off-by: David S. Miller <davem@davemloft.net>
drm/i915: Only apply the SNB pipe control w/a to gen6
Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).
Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322 Acked-by: Ben Widawsky <ben@bwidawsk.net> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.] Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm/i915: enable vdd when switching off the eDP panel
But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.
Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.
For reference the old bug, which hopefully doesn't get broken by this:
https://bugzilla.kernel.org/show_bug.cgi?id=43163
In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.
v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.
v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671 Tested-by: Roberto Romer <sildurin@gmail.com> Tested-by: Daniel Wagner <wagi@monom.org> Tested-by: Keith Packard <keithp@keithp.com> Cc: stable@vger.kernel.org Cc: Keith Packard <keithp@keithp.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Linus Torvalds [Tue, 14 Aug 2012 04:58:59 +0000 (07:58 +0300)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"Included are bug fixes and a patch to enable system call filtering
with BPF."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/compat: fix mmap compat system calls
s390/compat: fix compat wrappers for process_vm system calls
s390: do not clobber personality flags in sys_32_personality()
s390/seccomp: add support for system call filtering using BPF
s390/sclp_sdias: Add missing break and "fall through"
s390/mm: remove MAX_PHYSADDR_BITS define
Linus Torvalds [Tue, 14 Aug 2012 04:52:41 +0000 (07:52 +0300)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Radeon and intel fixes mostly, one fix to the mgag200 driver to not
hang on certain server variants."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (32 commits)
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
drm/mgag200: fix G200ER pll picking algorithm
drm/edid: Fix potential memory leak in edid_load()
drm/udl: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/radeon/kms: allow "invalid" DB formats as a means to disable DB
...
Arnd Bergmann [Mon, 13 Aug 2012 14:36:10 +0000 (14:36 +0000)]
GPIO: gpio-pxa: fix building without CONFIG_OF
Commit 7212157267 ("GPIO: gpio-pxa: fix devicetree functions") added an
"xlate" function pointer to the irq_domain_ops, but this function is nor
declared or defined anywhere when CONFIG_OF is disabled, causing the
build error:
drivers/gpio/gpio-pxa.c:532:11: error: 'irq_domain_xlate_twocell' undeclared here (not in a function)
Extending the DT-only code section to cover the irq_domain_ops and the
pxa_gpio_dt_ids solves this problem and makes it clearer which code is
actually used without DT.
Ben Skeggs [Fri, 27 Jul 2012 04:18:03 +0000 (14:18 +1000)]
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
At least partially fixes DP output detection on W530. Not sure if more
issues remain, or if my adaptor is just behaving weirdly (it does that
sometimes).
Dave Airlie [Mon, 13 Aug 2012 23:25:01 +0000 (09:25 +1000)]
Merge branch 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Alex Deucher writes:
This is the current set of radeon fixes for 3.6. Nothing too major.
Highlights:
- various display fixes
- some SI fixes
- new SI pci ids
- major VM fix
- CS checker support for MSAA
I've tested on a number of cards across generations and noticed no problems.
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
Jani Nikula [Mon, 13 Aug 2012 14:33:02 +0000 (17:33 +0300)]
drm/i915: ensure i2c adapter is all set before adding it
i2c_add_adapter() may do i2c transfers on the bus to detect supported
devices. Therefore the adapter needs to be all set before adding it. This
was not the case for the bit-banging fallback, resulting in an oops if the
device detection GMBUS transfers timed out. Fix the issue by calling
i2c_add_adapter() only after intel_gpio_setup().
LKML-Reference: <5021F00B.7000503@ionic.de> Tested-by: Mihai Moldovan <ionic@ionic.de> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jerome Glisse [Mon, 6 Aug 2012 16:32:21 +0000 (12:32 -0400)]
drm/radeon: fence virtual address and free it once idle v4
Virtual address need to be fenced to know when we can safely remove it.
This patch also properly clear the pagetable. Previously it was
serouisly broken.
Kernel 3.5/3.4 need a similar patch but adapted for difference in mutex locking.
v2: For to update pagetable when unbinding bo (don't bailout if
bo_va->valid is true).
v3: Add kernel 3.5/3.4 comment.
v4: Fix compilation warnings.
Signed-off-by: Jerome Glisse <jglisse@redhat.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
drm/radeon: do not reenable crtc after moving vram start address
It seems we can not update the crtc scanout address. After disabling
crtc, update to base address do not take effect after crtc being
reenable leading to at least frame being scanout from the old crtc
base address. Disabling crtc display request lead to same behavior.
So after changing the vram address if we don't keep crtc disabled
we will have the GPU trying to read some random system memory address
with some iommu this will broke the crtc engine and will lead to
broken display and iommu error message.
So to avoid this, disable crtc. For flicker less boot we will need
to avoid moving the vram start address.
projects / linux-beck.git / log